The -bios option is silently ignored if used in combination with -enable-kvm.
The reason is that the machine starts in S-Mode, and the bios typically runs in
M-Mode.
Better exit in that case to not confuse the user.
Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <20220401121842.2791796-1-ralf.ramsauer@oth-regensburg.de>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch updates the SPI_DEVICE, SPI_HOST0, SPI_HOST1
base addresses. Also adds these as unimplemented devices.
The address references can be found [1].
[1] 6c317992fb/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h (L107)
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220218063839.405082-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To facilitate software development of RISC-V systems with large number
of HARTs, we increase the maximum number of allowed CPUs to 512 (2^9).
We also add a detailed source level comments about limit defines which
impact the physical address space utilization.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-6-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate AIA APLIC devices only when
"aia=aplic" parameter is passed along with machine name in QEMU
command-line. When "aia=none" or not specified then we fallback
to original PLIC device emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-2-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We should use the AIA INTC compatible string in the CPU INTC
DT nodes when the CPUs support AIA feature. This will allow
Linux INTC driver to use AIA local interrupt CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-17-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following change was made to rectify incorrectly set stride length
on the PLIC [1]. Where it should be 32bit and not 24bit (0x18). This was
discovered whilst attempting to fix a bug where a timer_interrupt was
not serviced on TockOS-OpenTitan.
[1] https://docs.opentitan.org/hw/top_earlgrey/ip_autogen/rv_plic/doc/
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20220111071025.4169189-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When realising the SoC use error_fatal instead of error_abort as the
process can fail and report useful information to the user.
Currently a user can see this:
$ ../qemu/bld/qemu-system-riscv64 -M sifive_u -S -monitor stdio -display none -drive if=pflash
QEMU 6.1.93 monitor - type 'help' for more information
(qemu) Unexpected error in sifive_u_otp_realize() at ../hw/misc/sifive_u_otp.c:229:
qemu-system-riscv64: OTP drive size < 16K
Aborted (core dumped)
Which this patch addresses
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-8-alistair.francis@opensource.wdc.com>
The original BBL boot method had the kernel embedded as an opaque blob
that was blindly jumped to, which OpenSBI implemented as fw_payload.
OpenSBI then implemented fw_jump, which allows the payload to be loaded
elsewhere, but still blindly jumps to a fixed address at which the
kernel is to be loaded. Finally, OpenSBI introduced fw_dynamic, which
allows the previous stage to inform it where to jump to, rather than
having to blindly guess like fw_jump, or embed the payload as part of
the build like fw_payload. When used with an opaque binary (i.e. the
output of objcopy -O binary), it matches the behaviour of the previous
methods. However, when used with an ELF, QEMU currently passes on the
ELF's entry point address, which causes a discrepancy compared with all
the other boot methods if that entry point is not the first instruction
in the binary.
This difference specific to fw_dynamic with an ELF is not apparent when
booting Linux, since its entry point is the first instruction in the
binary. However, FreeBSD has a separate ELF entry point, following the
calling convention used by its bootloader, that differs from the first
instruction in the binary, used for the legacy SBI entry point, and so
the specific combination of QEMU's default fw_dynamic firmware with
booting FreeBSD as an ELF rather than a raw binary does not work.
Thus, align the behaviour when loading an ELF with the behaviour when
loading a raw binary; namely, use the base address of the loaded kernel
in place of the entry point.
The uImage code is left as-is in using the U-Boot header's entry point,
since the calling convention for that entry point is the same as the SBI
one and it mirrors what U-Boot will do.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211214032456.70203-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
A number of machines connect just one backend with drive_get_next().
Change them to use drive_get() directly. This makes the (zero) unit
number explicit in the code.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Cc: Niek Linnenbank <nieklinnenbank@gmail.com>
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-3-armbru@redhat.com>
ssi_sd_realize() creates an "sd-card" device. This is inappropriate,
and marked FIXME.
Move it to the boards that create these devices. Prior art: commit
eb4f566bbb for device "generic-sdhci", and commit 26c607b86b for
device "pl181".
The device remains not user-creatable, because its users should (and
do) wire up its GPIO chip-select line.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Fixup the PLIC context address to correctly support the threshold and
claim register.
Fixes: ef63100648 ("hw/riscv: opentitan: Update to the latest build")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211025040657.262696-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-5-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-4-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-3-alistair.francis@opensource.wdc.com
Add a generic function that can create the PLIC strings.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-2-alistair.francis@opensource.wdc.com
Using a macro for the PLIC configuration doesn't make the code any
easier to read. Instead it makes it harder to figure out what is going
on, so let's remove it.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20211022060133.3045020-1-alistair.francis@opensource.wdc.com
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
While at it add check for user supplied RAM size and error out if it
mismatches board expected value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
While at it add check for user supplied RAM size and error out if it
mismatches board expected value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Shortly, the set of supported XL will not be just 32 and 64,
and representing that properly using the enumeration will be
imperative.
Two places, booting and gdb, intentionally use misa_mxl_max
to emphasize the use of the reset value of misa.mxl, and not
the current cpu state.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-5-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If default main_mem is used to be registered as the system memory,
other memory cannot be initialized. Therefore, the system memory
should be initialized to the machine->ram, which consists of the
default main_mem and other possible memory required by applications,
such as shared hugepage memory in DPDK.
Also, the mc->defaul_ram_id should be set to the default main_mem,
such as "riscv_virt_board.ram" for the virt machine.
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211016030908.40480-1-limingwang@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Mark the shakti_c machine as not user creatable.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/639
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <c617a04d4e3dd041a3427b47a1b1d5ab475a2edd.1632871759.git.alistair.francis@wdc.com>
We extend virt machine to emulate ACLINT devices only when "aclint=on"
parameter is passed along with machine name in QEMU command-line.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-5-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We re-factor and break the FDT generation into smaller functions
so that it is easier to modify FDT generation for different
configurations of virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-4-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V ACLINT is more modular and backward compatible with
original SiFive CLINT so instead of duplicating the original
SiFive CLINT implementation we upgrade the current SiFive CLINT
implementation to RISC-V ACLINT implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-3-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We will be upgrading SiFive CLINT implementation into RISC-V ACLINT
implementation so let's first rename the sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 84d5b1d5783d2e79eee69a2f7ac480cc0c070db3.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 0364190bfa935058a845c0fa1ecf650328840ad5.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 0a76946981852f5bd15f0c37ab35b253371027a8.1630301632.git.alistair.francis@wdc.com
In the riscv virt machine init function, We assemble a string
plic_hart_config which is a comma-separated list of N copies of the
VIRT_PLIC_HART_CONFIG string. The code that does this has a
misunderstanding of the strncat() length argument. If the source
string is too large strncat() will write a maximum of length+1 bytes
(length bytes from the source string plus a trailing NUL), but the
code here assumes that it will write only length bytes at most.
This isn't an actual bug because the code has correctly precalculated
the amount of memory it needs to allocate so that it will never be
too small (i.e. we could have used plain old strcat()), but it does
mean that the code looks like it has a guard against accidental
overrun when it doesn't.
Rewrite the string handling here to use the glib g_strjoinv()
function, which means we don't need to do careful accountancy of
string lengths, and makes it clearer that what we're doing is
"create a comma-separated string".
Fixes: Coverity 1460752
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210812144647.10516-1-peter.maydell@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The flash is not inside the SoC, so it's inappropriate to put it
under the /soc node. Move it to root instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210807035641.22449-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use a dedicated UART config(CONFIG_SHAKTI_UART) to select
shakti uart.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210731190229.137483-1-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
arch_init.h only defines the QEMU_ARCH_* enumeration and the
arch_type global. Don't include it in files that don't use those.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210730105947.28215-8-peter.maydell@linaro.org
Only the Virt and Spike machines use NUMA. Add a RISCV_NUMA Kconfig
symbol and only have these machines select it. Adapt the Meson file
to only built it if required.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-8-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Coverity reports that we don't check the error result of fdt_pack(), so
let's save the result and assert that it is 0.
Fixes: Coverity CID 1458136
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 07325315b49d5555269f76094e4bc5296e0643b9.1626303527.git.alistair.francis@wdc.com
Currently the firmware dynamic info (fw_dyn) is put right after
the reset vector, which is not 8-byte aligned on RV64. OpenSBI
fw_dynamic uses ld to read contents from 'struct fw_dynamic_info',
which expects fw_dyn to be on the 8-byte boundary, otherwise the
misaligned load exception may happen. Fortunately this does not
cause any issue on QEMU, as QEMU does support misaligned load.
RV32 does not have any issue as it is 4-byte aligned already.
Change to make sure it is 8-byte aligned which works for both
RV32 and RV64.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210708143319.10441-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timebase frequency is set to 10MHz on sifive_u,
but on the real hardware the timebase frequency is 1Mhz.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210706102616.1922469-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect the Ibex timer to the OpenTitan machine. The timer can trigger
the RISC-V MIE interrupt as well as a custom device interrupt.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 5e7f4e9b4537f863bcb8db1264b840b56ef2a929.1624001156.git.alistair.francis@wdc.com
At present the Microchip Icicle Kit machine only supports using
'-bios' to load the HSS, and does not support '-kernel' for direct
kernel booting just like other RISC-V machines do. One has to use
U-Boot which is chain-loaded by HSS, to load a kernel for testing.
This is not so convenient.
Adding '-kernel' support together with the existing '-bios', we
follow the following table to select which payload we execute:
-bios | -kernel | payload
------+------------+--------
N | N | HSS
Y | don't care | HSS
N | Y | kernel
This ensures backwards compatibility with how we used to expose
'-bios' to users. When '-kernel' is used for direct boot, '-dtb'
must be present to provide a valid device tree for the board,
as we don't generate device tree.
When direct kernel boot is used, the OpenSBI fw_dynamic BIOS image
is used to boot a payload like U-Boot or OS kernel directly.
Documentation is updated to describe the direct kernel boot. Note
as of today there is still no PolarFire SoC support in the upstream
Linux kernel hence the document does not include instructions for
that. It will be updated in the future.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-8-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The OpenSBI BIOS image names are used by many RISC-V machines.
Let's define macros for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The official DT bindings of PLIC uses "sifive,plic-1.0.0" as the
compatible string in the upstream Linux kernel. "riscv,plic0" is
now legacy and has to be kept for backward compatibility of legacy
systems.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux kernel commit a2770b57d083 ("dt-bindings: timer: Add CLINT bindings")
adds the official DT bindings for CLINT, which uses "sifive,clint0"
as the compatible string. "riscv,clint0" is now legacy and has to
be kept for backward compatibility of legacy systems.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since commit 78da6a1bca ("device_tree: add qemu_fdt_setprop_string_array helper"),
we can use the new helper to set the compatible strings for the
SiFive test device node.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since commit 78da6a1bca ("device_tree: add qemu_fdt_setprop_string_array helper"),
we can use the new helper to set the clock name for the ethernet
controller node.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
imply VIRTIO_VGA for the virt machine, this fixes the following error
when specifying `-vga virtio` as a command line argument:
qemu-system-riscv64: Virtio VGA not available
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 7ac26fafee8bd59d2a0640f3233f8ad1ab270e1e.1617367317.git.alistair.francis@wdc.com
Update the OpenTitan interrupt layout to match the latest OpenTitan
bitstreams. This involves changing the Ibex PLIC memory layout and the
UART interrupts.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: e92b696f1809c9fa4410da2e9f23c414db5a6960.1617202791.git.alistair.francis@wdc.com
Connect one shakti uart to the shakti_c machine.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-5-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was accidentally dropped before. Add it back.
Fixes: 732612856a ("hw/riscv: Drop 'struct MemmapEntry'")
Reported-by: Emmanuel Blot <eblot.ml@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210331103612.654261-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a mechanical change to make the fdt available through
MachineState.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-3-alex.bennee@linaro.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
`link_up` is never used in gpex_pcie_init(). Drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the RISC-V defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210220144807.819-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
SIFIVE_U_CPU is conditionally set to SIFIVE_U34 or SIFIVE_U54, hence
there is no need to use #idef to set the mc->default_cpu_type.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210109143637.29645-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we place the DTB at 2MB from 4GB or end of DRAM which ever is
lesser. However, Linux kernel can address only 1GB of memory for RV32.
Thus, it can not map anything beyond 3GB (assuming 2GB is the starting address).
As a result, it can not process DT and panic if opensbi dynamic firmware
is used. While at it, place the DTB further away to avoid in memory placement
issues in future.
Fix this by placing the DTB at 16MB from 3GB or end of DRAM whichever is lower.
Fixes: 66b1205bc5 ("RISC-V: Copy the fdt in dram instead of ROM")
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Message-id: 20210107091127.3407870-1-atish.patra@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of using string compares to determine if a RISC-V machine is
using 32-bit or 64-bit CPUs we can use the initalised CPUs. This avoids
us having to maintain a list of CPU names to compare against.
This commit also fixes the name of the function to match the
riscv_cpu_is_32bit() function.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 8ab7614e5df93ab5267788b73dcd75f9f5615e82.1608142916.git.alistair.francis@wdc.com
Currently the riscv_is_32_bit() function only supports the generic rv32
CPUs. Extend the function to support the SiFive and LowRISC CPUs as
well.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-id: 9a13764115ba78688ba61b56526c6de65fc3ef42.1608142916.git.alistair.francis@wdc.com
The sifive_u machine emulates two UARTs but we have only UART0 DT
node in the generated DTB so this patch adds UART1 DT node in the
generated DTB.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201111094725.3768755-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Machine options can be retrieved as properties of the machine object.
Encourage that by removing the "easy" accessor to machine options.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Somehow HSS needs to access address 0 [1] for the DDR calibration data
which is in the chipset's reserved memory. Let's map it.
[1] See the config_copy() calls in various places in ddr_setup() in
the HSS source codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-9-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
It is not easy to find out the memory map for a specific component
in the PolarFire SoC as the information is scattered in different
documents. Add some comments so that people can know where to get
such information from the Microchip website.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend virt machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
to virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend sifive_u machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
or Linux SiFive DTB to sifive_u machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of loading the kernel at a hardcoded start address, let's load
the kernel at the next aligned address after the end of the firmware.
This should have no impact for current users of OpenSBI, but will
allow loading a noMMU kernel at the start of memory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 46c00c4f15b42feb792090e3d74359e180a6d954.1602634524.git.alistair.francis@wdc.com
Instead of returning the unused entry address from riscv_load_firmware()
instead return the end address. Also return the end address from
riscv_find_and_load_firmware().
This tells the caller if a firmware was loaded and how big it is. This
can be used to determine the load address of the next image (usually the
kernel).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 558cf67162342d65a23262248b040563716628b2.1602634524.git.alistair.francis@wdc.com
Allow the user to specify the main application CPU for the sifive_u
machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: b8412086c8aea0eff30fb7a17f0acf2943381b6a.1602634524.git.alistair.francis@wdc.com
Several callers of load_elf() pass pointers for lowaddr and highaddr
parameters which are then not used for anything. This may stem from a
misunderstanding that load_elf need a value here but in fact it can
take NULL to ignore these values. Remove such unused variables and
pass NULL instead from callers that don't need these.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20200705174020.BDD0174633F@zero.eik.bme.hu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200921221045.699690-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200921221045.699690-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (SIFIVE_U_OTP, SIFIVE_U_PRCI). This needs to be addressed
to allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_U_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with a QOM type check
macro (SIFIVE_E_PRCI). This needs to be addressed to allow us to
transform the QOM type check macros into functions generated by
OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_E_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
At present the Kconfig file is in disorder. Let's sort the options.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The name SIFIVE is too vague to convey the required component of
MSI_NONBROKEN. Let's drop the option, and select MSI_NONBROKEN in
each machine instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Every RISC-V machine needs riscv_hart hence there is no need to
have a dedicated Kconfig option for it. Drop the Kconfig option
and always build riscv_hart.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timestamp is using a hard-coded timebase
frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be
true for all boards.
Add a new 'timebase-freq' property to the CLINT device, and
update various functions to accept this as a parameter.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-16-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems
enough to create unimplemented devices to cover their register
spaces at this point.
With this commit, QEMU can boot to U-Boot (2nd stage bootloader)
all the way to the Linux shell login prompt, with a modified HSS
(1st stage bootloader).
For detailed instructions on how to create images for the Icicle
Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-15-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 2 Candence GEMs to provide
IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.
On the Icicle Kit board, GEM0 connects to a PHY at address 8 while
GEM1 connects to a PHY at address 9.
The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we
must specify 2 '-nic' options from the command line in order to get
a working ethernet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-14-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates one Cadence SDHCI controller.
On the Icicle Kit board, one eMMC chip and an external SD card
connect to this controller depending on different configuration.
As QEMU does not support eMMC yet, we just emulate the SD card
configuration. To test this, the Hart Software Services (HSS)
should choose the SD card configuration:
$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es
The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp
Note the generated SD card image should be resized before use:
$ qemu-img resize /path/to/sdcard.img 4G
Launch QEMU with the following command:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board
wires 4 of them out. Let's connect all 5 MMUARTs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that we have the newly introduced 'resetvec' property in the
RISC-V CPU and HART, instead of hard-coding the reset vector addr
in the CPU's instance_init(), move that to riscv_cpu_realize()
based on the configured property value from the RISC-V machines.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V machines do not instantiate RISC-V CPUs directly, instead
they do that via the hart array. Add a new property for the reset
vector address to allow the value to be passed to the CPU, before
CPU is realized.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
All Meson executables should specify their dependencies explicitly, either
directly or indirectly via declare_dependency. Makefiles instead did
not propagate dependencies correctly from static libraries, for example.
Therefore, flags for dependencies need not be included in QEMU_CFLAGS.
LIBS is not used at all, so drop that one as well.
In a few cases the dependencies were not yet specified, so add them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (IBEX_PLIC, IBEX_UART). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to IBEX_DEV_*, to avoid conflicts.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We extend RISC-V virt machine to allow creating a multi-socket
machine. Each RISC-V virt machine socket is a NUMA node having
a set of HARTs, a memory instance, a CLINT instance, and a PLIC
instance. Other devices are shared between all sockets. We also
update the generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V virt
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V virt machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-6-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend RISC-V spike machine to allow creating a multi-socket
machine. Each RISC-V spike machine socket is a NUMA node having
a set of HARTs, a memory instance, and a CLINT instance. Other
devices are shared between all sockets. We also update the
generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V spike
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V spike machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-5-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We add common helper routines which can be shared by RISC-V
multi-socket NUMA machines.
We have two types of helpers:
1. riscv_socket_xyz() - These helper assist managing multiple
sockets irrespective whether QEMU NUMA is enabled/disabled
2. riscv_numa_xyz() - These helpers assist in providing
necessary QEMU machine callbacks for QEMU NUMA emulation
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-4-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend PLIC emulation to allow multiple instances of PLIC in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from PLIC emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200616032229.766089-3-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend CLINT emulation to allow multiple instances of CLINT in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from CLINT emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-Id: <20200616032229.766089-2-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To keep sync with other RISC-V machines, change the default bios to
use generic platform fw_dynamic.elf image.
While we are here, add some comments to mention that using ELF files
for the Spike machine was intentional.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1596439832-29238-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Update virt and sifive_u machines to use the opensbi fw_dynamic bios
image built for the generic FDT platform.
Remove the out-of-date no longer used bios images.
Note:
1. To test 32-bit Linux kernel on QEMU 'sifive_u' 32-bit machine,
the following patch is needed:
http://lists.infradead.org/pipermail/linux-riscv/2020-July/001213.html
2. To test 64-bit Linux 5.3 kernel on QEMU 'virt' or 'sifive_u' 64-bit
machines, the following commit should be cherry-picked to 5.3:
commit 922b0375fc93fb1a20c5617e37c389c26bbccb70
Author: Albert Ou <aou@eecs.berkeley.edu>
Date: Fri Sep 27 16:14:18 2019 -0700
riscv: Fix memblock reservation for device tree blob
Linux 5.4 or above already contains this commit/fix.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1596439832-29238-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
It is enough to simply map the SiFive FU540 L2 cache controller
into the MMIO space using create_unimplemented_device(), with an
FDT fragment generated, to make the latest upstream U-Boot happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1595227748-24720-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Each architecture's sourceset is placed in an hw_arch dictionary, and picked up
from there when building the per-emulator static_library.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently the debug region size is set to 0x100, but according to
FE310-G000 and FE310-G002 manuals:
FE310-G000: 0x100 - 0xFFF
FE310-G002: 0x0 - 0xFFF
Change the size to 0x1000 that applies to both.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1594891856-15474-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
nd_table[] contains NIC configuration for boards to pick up. Device
code has no business looking there. Several devices do it anyway.
Two of them already have a suitable FIXME comment: "allwinner-a10" and
"msf2-soc". Copy it to the others: "allwinner-h3", "xlnx-versal",
"xlnx,zynqmp", "sparc32-ledma", "riscv.sifive.u.soc".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200715140440.3540942-3-armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
At present the size of Mask ROM for sifive_u / spike / virt machines
is set to 0x11000, which ends at an unusual address. This changes the
size to 0xf000 so that it ends at 0x10000.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1594289144-24723-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Even though the start address in ROM code is declared as a 64 bit address
for RV64, it can't be used as upper bits are set to zero in ROM code.
Update the ROM code correctly to reflect the 64bit value.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-5-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
OpenSBI is the default firmware in Qemu and has various firmware loading
options. Currently, qemu loader uses fw_jump which has a compile time
pre-defined address where fdt & kernel image must reside. This puts a
constraint on image size of the Linux kernel depending on the fdt location
and available memory. However, fw_dynamic allows the loader to specify
the next stage location (i.e. Linux kernel/U-Boot) in memory and other
configurable boot options available in OpenSBI.
Add support for OpenSBI dynamic firmware loading support. This doesn't
break existing setup and fw_jump will continue to work as it is. Any
other firmware will continue to work without any issues as long as it
doesn't expect anything specific from loader in "a2" register.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-4-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the fdt is copied to the ROM after the reset vector. The firmware
has to copy it to DRAM. Instead of this, directly copy the device tree to a
pre-computed dram address. The device tree load address should be as far as
possible from kernel and initrd images. That's why it is kept at the end of
the DRAM or 4GB whichever is lesser.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-3-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, all riscv machines except sifive_u have identical reset vector
code implementations with memory addresses being different for all machines.
They can be easily combined into a single function in common code.
Move it to common function and let all the machines use the common function.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20200701183949.398134-2-atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adjust the PCIe memory maps to follow the order.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1593746511-19517-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
Commit 5d971f9e67
"memory: Revert "memory: accept mismatching sizes in
memory_region_access_valid"" broke most RISC-V boards as they do 64 bit
accesses to the CLINT and QEMU would trigger a fault. Fix this failure
by allowing 8 byte accesses.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
Message-Id: <122b78825b077e4dfd39b444d3a46fe894a7804c.1593547870.git.alistair.francis@wdc.com>
Claiming an interrupt and changing the source priority both potentially
affect whether an interrupt is pending, thus we must re-compute xEIP.
Note that we don't put the sifive_plic_update inside sifive_plic_claim
so that the logging of a claim (and the resulting IRQ) happens before
the state update, making the causal effect clear, and that we drop the
explicit call to sifive_plic_print_state when claiming since
sifive_plic_update already does that automatically at the end for us.
This can result in both spurious interrupt storms if you fail to
complete an IRQ before enabling interrupts (and no other actions occur
that result in a call to sifive_plic_update), but also more importantly
lost interrupts if a disabled interrupt is pending and then becomes
enabled.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200618210649.22451-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The source priorities can be used to order sources with respect to other
sources, not just as a way to enable/disable them based off a threshold.
We must therefore always claim the highest-priority source, rather than
the first source we find.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200618202343.20455-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
riscv_harts_realize() is wrong that way: it passes @errp to
riscv_hart_realize() in a loop. I can't tell offhand whether this can
fail.
Fix by checking for failure in each iteration.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630090351.1247703-19-armbru@redhat.com>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
sifive_u_soc_realize() is wrong that way: it passes &err to
sysbus_realize() four times before checking it. Harmless, because the
first three can't actually fail (I think).
Fix by checking for failure right away.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630090351.1247703-18-armbru@redhat.com>
It is enough to simply map the SiFive FU540 DDR memory controller
into the MMIO space using create_unimplemented_device(), to make
the upstream U-Boot v2020.07 DDR memory initialization codes happy.
Note we do not generate device tree fragment for the DDR memory
controller. Since the controller data in device tree consumes a
very large space (see fu540-hifive-unleashed-a00-ddr.dtsi in the
U-Boot source), and it is only needed by U-Boot SPL but not any
operating system, we choose not to generate the fragment here.
This also means when testing with U-Boot SPL, the device tree has
to come from U-Boot SPL itself, but not the one generated by QEMU
on the fly. The memory has to be set to 8GiB to match the real
HiFive Unleashed board when invoking QEMU (-m 8G).
With this commit, QEMU can boot U-Boot SPL built for SiFive FU540
all the way up to loading U-Boot proper from MMC:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -m 8G -bios u-boot-spl.bin
U-Boot SPL 2020.07-rc3-00208-g88bd5b1 (Jun 08 2020 - 20:16:10 +0800)
Trying to boot from MMC1
Unhandled exception: Load access fault
EPC: 0000000008009be6 TVAL: 0000000010050014
The above exception is expected because QSPI is unsupported yet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-6-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the flash and DRAM to the end of the SoC memmap table.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-5-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC supports booting from several sources, which are
controlled using the Mode Select (MSEL[3:0]) pins on the chip.
Typically, the boot process runs through several stages before it
begins execution of user-provided programs.
The SoC supports booting from memory-mapped QSPI flash, which is
how start_in_flash property is used for at present. This matches
MSEL = 1 configuration (QSPI0).
Typical booting flows involve the Zeroth Stage Boot Loader (ZSBL).
It's not necessary for QEMU to implement the full ZSBL ROM codes,
because we know ZSBL downloads the next stage program into the L2
LIM at address 0x8000000 and executes from there. We can bypass
the whole ZSBL execution and use "-bios" to load the next stage
program directly if MSEL indicates a ZSBL booting flow.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-4-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per the SiFive manual, all E/U series CPU cores' reset vector is
at 0x1004. Update our codes to match the hardware.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1592268641-7478-3-git-send-email-bmeng.cn@gmail.com
Message-Id: <1592268641-7478-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On SiFive FU540 SoC, the value stored at physical address 0x1000
stores the MSEL pin state that is used to control the next boot
location that ROM codes jump to.
Add a new property msel to sifive_u machine for this.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-12-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In prepration to add more properties to this machine, rename the
existing serial property get/set functions to a generic name.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-11-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The HiFive Unleashed board wires GPIO pin#10 to the input of the
system reset signal. Let's set up the GPIO pin#10 and insert a
"gpio-restart" device tree node so that reboot is now functional
with QEMU 'sifive_u' machine.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-10-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the GPIO output IRQs are triggered each time any GPIO
register is written. However this is not correct. We should only
trigger the output IRQ when the pin is configured as output enable.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-9-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a GPIO controller with 16 GPIO lines.
This hooks the exsiting SiFive GPIO model to the SoC, and adds its
device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-8-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a new property to represent the number of GPIO pins supported
by the GPIO controller.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-7-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Do various minor clean-ups to the exisiting codes for:
- coding convention conformance
- remove unnecessary blank lines
- spell SiFive correctly
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-6-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Upstream U-Boot v2020.07 codes switch to access SiFive FU540 OTP
based on device tree information. Let's generate the device tree
node for OTP.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-5-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to retrieve all PLIC IRQ information in order to
just connect the GEM IRQ. Use qdev_get_gpio_in() directly like
what is done for other peripherals.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-4-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but opentitan codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-3-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but sifive_e codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is the initial commit of the Ibex UART device. Serial TX is
working, while RX has been implemeneted but untested.
This is based on the documentation from:
https://docs.opentitan.org/hw/ip/uart/doc/
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
This is the same transformation as in the previous commit, except
sysbus_init_child_obj() and realize are too separated for the commit's
Coccinelle script to handle, typically because sysbus_init_child_obj()
is in a device's instance_init() method, and the matching realize is
in its realize() method.
Perhaps a Coccinelle wizard could make it transform that pattern, but
I'm just a bungler, and the best I can do is transforming the two
separate parts separately:
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(OBJECT(child), true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(child, true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
@@
- qdev_init_nofail(DEVICE(child));
+ sysbus_realize(SYS_BUS_DEVICE(child), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
expression dev;
@@
dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
identifier dev;
@@
DeviceState *dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression parent, name, size, type;
expression child;
symbol true;
@@
- sysbus_init_child_obj(parent, name, child, size, type);
+ sysbus_init_child_XXX(parent, name, child, size, type);
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, child, sizeof(*child), type)
+ object_initialize_child(parent, propname, child, type)
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, &child, sizeof(child), type)
+ object_initialize_child(parent, propname, &child, type)
This script is *unsound*: we need to manually verify init and realize
conversions are properly paired.
This commit has only the pairs where object_initialize_child()'s
@child and sysbus_realize()'s @dev argument text match exactly within
the same source file.
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-49-armbru@redhat.com>
The callers of object_initialize_child() commonly pass either
&child, sizeof(child), or pchild, sizeof(*pchild). Tidy up the few
that don't, mostly to keep the next commit simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-36-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is somewhere between
not worthwhile and infeasible (at least for me).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-11-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
riscv_sifive_e_soc_init(), riscv_sifive_u_soc_init(),
spike_board_init(), spike_v1_10_0_board_init(),
spike_v1_09_1_board_init(), and riscv_virt_board_init() create
"riscv-hart_array" sysbus devices in a way that leaves them unplugged.
Create them the common way that puts them into the main system bus.
Affects machines sifive_e, sifive_u, spike, spike_v1.10, spike_v1.9.1,
and virt. Visible in "info qtree", here's the change for sifive_e:
bus: main-system-bus
type System
+ dev: riscv.hart_array, id ""
+ num-harts = 1 (0x1)
+ hartid-base = 0 (0x0)
+ cpu-type = "sifive-e31-riscv-cpu"
dev: sifive_soc.gpio, id ""
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200609122339.937862-20-armbru@redhat.com>
This adds a barebone OpenTitan machine to QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The ISA specific Spike machines have been deprecated in QEMU since 4.1,
let's finally remove them.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Remove the riscv_ prefix of the machine* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1590072147-13035-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1590072147-13035-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To keep consistency with the machine* functions, remove the riscv_
prefix of the soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1590072147-13035-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1590072147-13035-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per QEMU deprecated doc, QEMU 4.1 introduced support for the -bios
option in QEMU for RISC-V for the virt machine and sifive_u machine.
The default behavior has been that QEMU does not automatically load
any firmware if no -bios option is included.
Now 2 releases passed, it's time to change the default behavior to
load the default OpenSBI firmware automatically. The firmware is
included with the QEMU release and no user interaction is required.
All a user needs to do is specify the kernel they want to boot with
the -kernel option.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1588335545-649-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1588335545-649-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
