Move the utility function extended_addresses_enabled() into
internals.h; we're going to need to call it from op_helper.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement support for setting QEMU watchpoints based on the
values the guest writes to the ARM architected watchpoint
registers. (We do not yet report the firing of the watchpoints
to the guest, so they will just be ignored.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a single misindented line in arm_cpu_reset().
Signed-off-by: Martin Galvan <martin.galvan@tallertechnologies.com>
[PMM: split this out from the previous commit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When calling qemu_system_reset after startup on a Cortex-M
CPU, the initial values of PC, MSP and the Thumb bit weren't being set
correctly if the vector table was in ROM. In particular, since Thumb was 0, a
Usage Fault would arise immediately after trying to execute any instruction
on a Cortex-M.
Signed-off-by: Martin Galvan <martin.galvan@tallertechnologies.com>
Message-id: CAOKbPbaLt-LJsAKkQdOE0cs9Xx4OWrUfpDhATXPSdtuNw2xu_A@mail.gmail.com
[PMM: removed an incorrect comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the function that is called when writing to the
PMCCFILTR_EL0 register
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 73da3da6404855b17d5ae82975a32ff3a4dcae3d.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the old PMCCNTR code and replace it with calls to the new
pmccntr_sync() and arm_ccnt_enabled() functions.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 693a6e437d915c2195fd3dc7303f384ca538b7bf.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is used to synchronise the PMCCNTR counter and swap its
state between enabled and disabled if required. It must always
be called twice, both before and after any logic that could
change the state of the PMCCNTR counter.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 62811d4c0f7b1384f7aab62ea2fcfda3dcb0db50.1409025949.git.peter.crosthwaite@xilinx.com
[PMM: fixed minor typos in pmccntr_sync doc comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Include a helper function to determine if the CCNT counter
is enabled.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: e1a64f17a756e06c8bda8238ad4826d705049f7a.1409025949.git.peter.crosthwaite@xilinx.com
[ PC changes
* Remove EL based checks
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for the ARMv8 version of the PMCCNTR and
related registers. It also starts to implement the PMCCFILTR_EL0
register.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: b5d1094764a5416363ee95216799b394ecd011e8.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The register is now 64bit, however a 32 bit write to the register
should leave the higher bits unchanged. The open coded write handler
does not implement this, so we need to read-modify-write accordingly.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Alistair Francis <alistair23@gmail.com>
Message-id: ec350573424bb2adc1701c3b9278d26598e2f2d1.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This makes the PMCCNTR register 64-bit to allow for the
64-bit ARMv8 version.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 6c5bac5fd0ea54963b1fc0e7f9464909f2e19a73.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We implement the crypto extensions but were incorrectly reporting
ID register values for the Cortex-A57 which did not advertise
crypto. Use the correct values as described in the TRM.
With this fix Linux correctly detects presence of the crypto
features and advertises them in /proc/cpuinfo.
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1408718660-7295-1-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 2c7ffc414 added support for honouring the CPACR coprocessor
access control register bits which may disable access to VFP
and Neon instructions. However it failed to account for the
fact that the CPACR is only present starting from the ARMv6
architecture version, so it accidentally disabled VFP completely
for ARMv5 CPUs like the ARM926. Linux would detect this as
"no VFP present" and probably fall back to its own emulation,
but other guest OSes might crash or misbehave.
This fixes bug LP:1359930.
Reported-by: Jakub Jermar <jakub@jermar.eu>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1408714940-7192-1-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For A9, The cache associativity is 4 and the lines size is 32B.
Self identify in CCSIDR accordingly. Cache size remains at 16k.
QEMU doesn't emulate caches, but we should still report the correct
cache-line size to the guest. Some guests (like u-boot) complain if
the cache-line size mismatches a requested flush or invalidate
operation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1de6bd40155a1d2f2e93e24b1b1d1d677a432641.1408346233.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current code supplies the PSCI v0.1 function IDs in the DT even when
KVM uses PSCI v0.2.
This will break guest kernels that only support PSCI v0.1 as they will
use the IDs provided in the DT. Guest kernels with PSCI v0.2 support
are not affected by this patch, because they ignore the function IDs in
the device tree and rely on the architecture definition.
Define QEMU versions of the constants and check that they correspond to
the Linux defines on Linux build hosts. After this patch, both guest
kernels with PSCI v0.1 support and guest kernels with PSCI v0.2 should
work.
Tested on TC2 for 32-bit and APM Mustang for 64-bit (aarch64 guest
only). Both cases tested with 3.14 and linus/master and verified I
could bring up 2 cpus with both guest kernels. Also tested 32-bit with
a 3.14 host kernel with only PSCI v0.1 and both guests booted here as
well.
Cc: qemu-stable@nongnu.org
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function IDs for PSCI v0.1 are exported by KVM and defined as
KVM_PSCI_FN_<something>. To build using these defines in non-KVM code,
QEMU defines these IDs locally and check their correctness against the
KVM headers when those are available.
However, the naming scheme used for QEMU (almost) clashes with the PSCI
v0.2 definitions from Linux so to avoid unfortunate naming when we
introduce local PSCI v0.2 defines, rename the current local defines with
QEMU_ prependend and clearly identify the PSCI version as v0.1 in the
defines.
Cc: qemu-stable@nongnu.org
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that all the new code to support single-stepping is in
place, wire up the guest-visible MDSCR_EL1, so the guest
can enable single-stepping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
ARMv8 single-stepping requires the exception level that controls
the single-stepping to be in AArch64 execution state, but the
code being stepped may be in AArch64 or AArch32. Implement the
necessary support code for single-stepping AArch32 code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Implement ARMv8 software single-step handling for A64 code:
correctly update the single-step state machine and generate
debug exceptions when stepping A64 code.
This patch has no behavioural change since MDSCR_EL1.SS can't
be set by the guest yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
If gen_goto_tb() decides not to link the two TBs, then the
fallback path generates unnecessary code:
* if singlestep is enabled then we generate unreachable code
after the gen_exception_internal(EXCP_DEBUG)
* if singlestep is disabled then we will generate exit_tb(0)
twice, once in gen_goto_tb() and once coming out of the
main loop with is_jmp set to DISAS_JUMP
Correct these deficiencies by only emitting exit_tb() in the
non-singlestep case, in which case we can use DISAS_TB_JUMP
to suppress the main-loop exit_tb().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Set the PSTATE.SS bit correctly on exception returns from AArch64,
as required by the debug single-step functionality.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
When an exception is taken to AArch32, we must clear the PSTATE.SS
bit for the exception handler, and must also ensure that the SS bit
is not set in the value saved to SPSR_<mode>. Achieve both of these
aims by clearing the bit in uncached_cpsr before saving it to the SPSR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
The CPSR has a new-in-v8 execution state bit (IL), and
also some state which has effects in AArch32 but appears
only in the SPSR format (SS) but is RES0 in the CPSR.
Add the IL bit to CPSR_EXEC, and enforce that guest direct
reads and writes to CPSR can't read or write the RES0
bits, so the guest can't get at the SS bit which we store
in uncached_cpsr. This includes not permitting exception
returns to copy reserved bits from an SPSR into CPSR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Allow each CPU type to specify the value for the debug ID
registers, by putting them in the ARMCPU struct, and use
the resulting information to only expose the correct number
of watchpoint and breakpoint registers for the CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Bring the 32 bit and 64 bit views of the debug registers into
line by providing the same set of registers in both cases.
(This still isn't a complete set, but it is consistent.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Currently the STATE_BOTH shorthand for allowing a single reginfo struct
to define handling for both AArch32 and AArch64 views of a register
only permits this where the AArch32 view is in cp15. It turns out that
the debug registers in cp14 also have neatly lined up encodings;
allow these also to share reginfo structs by permitting a STATE_BOTH
reginfo to specify the .cp field (and continue to default to 15 if
it is not specified).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
At the moment we have a mixed set of mostly dummy register
definitions for various debug related registers which have
been added piecemeal in order to get Linux kernels to boot.
In preparation for actually implementing debug support,
bring them all together into one place.
This commit doesn't change behaviour: we still expose
exactly the same registers and behaviour to the guest
in all configurations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
When we take an exception resulting from a BRK instruction,
the architecture requires that the "preferred return address"
reported to the exception handler is the address of the BRK
itself, not the following instruction (like undefined
insns, and in contrast with SVC, HVC and SMC). Follow this,
rather than incorrectly reporting the address of the following
insn.
(We do get this correct for the A32/T32 BKPT insns.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
According to the ARM ARM we weren't correctly flushing the TLB entries
where bits 63:56 didn't match bit 55 of the virtual address. This
exposed a problem when we switched QEMU's internal TARGET_PAGE_BITS to
12 for aarch64.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1406733627-24255-3-git-send-email-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Otherwise we break quickly when we change TARGET_PAGE_SIZE.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1406733627-24255-2-git-send-email-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Static code analyzers complain about a dubious & operation used for a
boolean value. The code does not test the PSTATE_SP bit as it should.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1406359601-25583-1-git-send-email-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-7-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-6-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change.
Prepares for future additions of the EL2 and 3 versions of this reg.
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1402994746-8328-5-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Break out code to save/restore AArch64 SP into functions.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1402994746-8328-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement kvm_arm_vcpu_init() as a simple call to arm_arm_vcpu_init()
(which uses the KVM_ARM_VCPU_INIT vcpu ioctl to tell the kernel
to re-initialize the vCPU), rather than via the complicated code
which saves a copy of the register state on first init and then
writes it back to the kernel. This is much simpler and brings the
32-bit KVM code into line with the 64-bit code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1403802973-20841-1-git-send-email-peter.maydell@linaro.org
We require to know the PSCI version available to given CPU at
potentially many places. Currently, we need to know PSCI version
when generating DTB for virt machine.
This patch introduce per-CPU 32bit field representing the PSCI
version available to the CPU. The encoding of this 32bit field
is same as described in PSCI v0.2 spec.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-8-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To implement kvm_arch_reset_vcpu(), we simply re-init the VCPU
using kvm_arm_vcpu_init() so that all registers of VCPU are set
to their reset values by in-kernel KVM code.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-7-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Latest linux kernel supports in-kernel emulation of PSCI v0.2 but
to enable it we need to select KVM_ARM_VCPU_PSCI_0_2 feature using
KVM_ARM_VCPU_INIT ioctl.
Also, we can use KVM_ARM_VCPU_PSCI_0_2 feature for VCPU only when
linux kernel has KVM_CAP_ARM_PSCI_0_2 capability.
This patch updates kvm_arch_init_vcpu() to enable KVM_ARM_VCPU_PSCI_0_2
feature for VCPU when KVM ARM/ARM64 has KVM_CAP_ARM_PSCI_0_2 capability.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-6-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a common kvm_arm_vcpu_init() for doing KVM_ARM_VCPU_INIT
ioctl in KVM ARM and KVM ARM64. This also helps us factor-out few
common code lines from kvm_arch_init_vcpu() for KVM ARM/ARM64.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-5-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In handle_simd_shift_fpint_conv(), the combination of is_double == true,
is_scalar == false and is_q == false is an unallocated encoding; the
'both parts false' case of the nested ?: expression for calculating
maxpass is therefore unreachable and can be removed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1402171881-14343-4-git-send-email-peter.maydell@linaro.org
In disas_simd_3same_int(), none of the instructions permit is_q
to be false with size == 3 (this would be a vector operation with
a one-element vector, and the instruction set encodes those as
scalar operations). Replace the always-true ?: check with an
assert.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1402171881-14343-3-git-send-email-peter.maydell@linaro.org
The maximum block size for AArch64 address translation is 2GB. This means
that we need a ULL suffix on our shift to avoid shifting into the sign
bit of a signed 32 bit integer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1402171881-14343-2-git-send-email-peter.maydell@linaro.org
Corrected handling of writes to TTBCR for ARMv8 (previously UNK/SBZP
bits are not RES0) and ARMv7 (new bits PD0/PD1 for CPUs with Security
Extensions).
Bits PD0/PD1 are now respected in get_phys_addr_v6/v5() and
get_level1_table_address.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Message-id: 1402409556-18574-1-git-send-email-aggelerf@ethz.ch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch refactors the ARM cryptographic instructions to use the
(newly) added common tables from include/qemu/aes.h.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The iwmmxt_msadb helper and its corresponding gen function are unused;
delete them. (This function appears to have never been used right back
to the initial implementation of iwMMXt; it is identical to iwmmxt_madduq,
and is presumably an accidental remnant from the initial development.)
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401822125-1822-1-git-send-email-peter.maydell@linaro.org
The code for handling writes to the generic timer control registers
had several bugs:
* ISTATUS (bit 2) is read-only but we forced it to zero on any write
* the check for "was IMASK (bit 1) toggled?" incorrectly used '&' where
it should be '^'
* the handling of IMASK was inverted: we should set the IRQ if
ISTATUS is set and IMASK is clear, not if both are set
The combination of these bugs meant that when running a Linux guest
that uses the generic timers we would fairly quickly end up either
forgetting that the timer output should be asserted, or failing to
set the IRQ when the timer was unmasked. The result is that the guest
never gets any more timer interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401803208-1281-1-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Bring the 32-bit CRC helper functions into line with the A64 ones,
by masking the high bytes of the value in the calling code rather
than the helper. This is more efficient since we can determine the
mask at translation time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401458125-27977-7-git-send-email-peter.maydell@linaro.org
VFPv4 implies the presence of the half-precision floating point
extension (which is optional in VFPv3). Add this implied rule
to arm_cpu_realizefn() and remove some no-longer-needed explicit
setting of the bit in initfns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401458125-27977-5-git-send-email-peter.maydell@linaro.org
CRC and crypto are both optional v8 extensions, so FEATURE_V8
should not imply them. Instead we should set these bits in the
initfns for the 32-bit and 64-bit "cpu any" and for the Cortex-A57.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401458125-27977-4-git-send-email-peter.maydell@linaro.org
FEATURE_V8 implies both FEATURE_V7MP and FEATURE_ARM_DIV, so
we don't need to set them explicitly in initfns which set the
V8 feature bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401458125-27977-3-git-send-email-peter.maydell@linaro.org
The arm_any_initfn() is used only for the 32-bit linux-user "cpu any",
so it only gets called in builds where TARGET_AARCH64 is not defined.
Remove the unreachable line which sets ARM_FEATURE_AARCH64.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401458125-27977-2-git-send-email-peter.maydell@linaro.org
Now that we have a separate ARM_FEATURE_V8_PMULL bit, use it for
the A64 PMULL, not the AES feature bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the VMULL.P64 polynomial 64x64 to 128 bit multiplication
instruction in the A32/T32 instruction sets; this is part of the v8
Crypto Extensions.
To do this we have to move the neon_pmull_64_{lo,hi} helpers from
helper-a64.c into neon_helper.c so they can be used by the AArch32
translator.
Inspired-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401386724-26529-4-git-send-email-peter.maydell@linaro.org
The current undefreq field in the neon_3reg_wide handling allows us
to encode "UNDEF if size != 0" and "UNDEF if size == 0". This is
no longer sufficient with the advent of 64-bit polynomial VMULL,
which means we want to UNDEF if size == 1. Change the undefreq
encoding to use separate bits for all of "UNDEF if size == 0",
"UNDEF if size == 1" and "UNDEF if size == 2".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401386724-26529-3-git-send-email-peter.maydell@linaro.org
This adds support for the SHA1 and SHA256 instructions that are available
on some v8 implementations of Aarch32.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1401386724-26529-2-git-send-email-peter.maydell@linaro.org
[PMM:
* rebase
* fix bad indent
* add a missing UNDEF check for Q!=1 in the 3-reg SHA1/SHA256 case
* use g_assert_not_reached()
* don't re-extract bit 6 for the 2-reg-misc encodings
* set the ELF HWCAP2 bits for the new features
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In v8 page tables bit 54 in the PTE is UXN in the EL0/EL1 translation regimes
and XN elsewhere. In v7 the bit is always XN. Since we only emulate EL0/EL1 we
can just treat this bit as UXN whenever we are in v8 mode.
Also correctly extract the upper attributes from the PTE entry, the v8 version
tried to avoid extracting the CONTIG bit and ended up with the upper bits being
off-by-one. Instead behave the same as v7 and extract (but ignore) the CONTIG
bit.
This fixes "Bad mode in Synchronous Abort handler detected, code 0x8400000f"
seen when modprobing modules under Linux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Claudio Fontana <claudio.fontana@huawei.com>
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch changes some readfns/writefns to use raw_write
and raw_read functions, which use the fieldoffset specified
in ARMCPRegInfo instead of directly accessing the field.
This will simplify patches for EL3 & Security Extensions.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Message-id: 1401962428-14749-1-git-send-email-aggelerf@ethz.ch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cpu64.c contains a reginfo list for the impdef registers on
the Cortex-A57; however we forgot to actually call define_arm_cp_regs(),
so it was sitting there doing nothing. Remedy this omission.
Message-id: 1401226259-23121-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will collect all load and store helpers soon. For now
it is just a replacement for softmmu_exec.h, which this patch
stops including directly, but we also include it where this will
be necessary in order to simplify the next patch.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These will soon require cpu_ldst.h, so move them out of cpu.h.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They do not need to be in op_helper.c. Because cputlb.c now includes
softmmu_template.h twice for each size, io_readX must be elided the
second time through.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than include helper.h with N values of GEN_HELPER, include a
secondary file that sets up the macros to include helper.h. This
minimizes the files that must be rebuilt when changing the macros
for file N.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-24-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-23-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-22-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-21-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds support for ERET to and from AArch64 EL2 and 3.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-20-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-19-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-18-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-17-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-16-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-15-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-14-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add aarch64_banked_spsr_index(), used to map an Exception Level
to an index in the banked_spsr array.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-13-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-12-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-11-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-10-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change.
Preparation for adding EL2 and 3 versions of this reg.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-9-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change.
Prepares for future addtion of EL2 and 3 versions of this reg.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-8-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change.
Prepares for future additions of the EL2 and 3 versions of this reg.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1400980132-25949-7-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid using IS_USER directly as the MMU-idx to simplify future
changes to the MMU layout.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1400980132-25949-5-git-send-email-edgar.iglesias@gmail.com
Message-id: 1400805738-11889-6-git-send-email-edgar.iglesias@gmail.com
[PMM: parts relating to LDRT/STRT moved into earlier patches]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRS instruction was using a hardcoded 0 for the memory
accesses. This happens to be OK since the SRS instruction is
UNPREDICTABLE in User and System modes, but is awkward if we
want to rearrange the MMU index uses. Switch to using
get_mem_index() like all the other accesses.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1400980132-25949-4-git-send-email-edgar.iglesias@gmail.com
Clean up the mmu index handling for ldrt/strt insns: instead
of a flag 'user' indicating whether to treat the store as user
mode or not, use 'memidx' to indicate the correct memory index to use.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1400980132-25949-3-git-send-email-edgar.iglesias@gmail.com
In ARMv7 the CPACR register allows to control access rights to
coprocessor 0-13 interfaces. Bits corresponding to unimplemented
coprocessors should be RAZ/WI. Bits ASEDIS, D32DIS, TRCDIS are
UNK/SBZP if VFP is not implemented and RAO/WI in some cases.
Treating TRCDIS as RAZ/WI since we neither implement a trace
macrocell nor a CP14 interface to the trace macrocell registers.
Since CPACR bits for VFP/Neon access are honoured with the CPACR_FPEN
bit in the TB flags, flushing the TLB is not necessary anymore.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Message-id: 1400532968-30668-1-git-send-email-aggelerf@ethz.ch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 50a2c6e55f introduced a bug where QEMU would segfault on startup
when using KVM on ARM hosts, because kvm_arm_reset_cpu() accesses
cpu->cpreg_reset_values, which is not allocated before
kvm_arch_init_vcpu(). Fix this by not calling cpu_reset() until after
qemu_init_vcpu().
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1401194263-13010-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux makes a habit of writing the same value to the SCTLR that it
already holds. In a sample boot of the kernel to a shell prompt
it wrote the SCTLR with the value it already held 325465 times,
and wrote different values just 3 times.
Skip flushing the TLB if the SCTLR value isn't actually being changed;
this speeds up my sample boot by 3-5%.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1399560029-19007-1-git-send-email-peter.maydell@linaro.org
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we have a CPU object with a reset method, it is better to
keep the KVM reset close to the CPU reset. Using qemu_register_reset
as we do now keeps them far apart.
With this patch, PPC no longer calls the kvm_arch_ function, so
it can get removed there. Other arches call it from their CPU
reset handler, and the function gets an ARMCPU/X86CPU/S390CPU.
Note that ARM- and s390-specific functions are called kvm_arm_*
and kvm_s390_*, while x86-specific functions are called kvm_arch_*.
That follows the convention used by the different architectures.
Changing that is the topic of a separate patch.
Reviewed-by: Gleb Natapov <gnatapov@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As the macro verifies the value is positive, rename it
to make the function clearer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Harmless typo as opc1 defaults to zero and opc2 gets
re-declared to its correct value.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1398926097-28097-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For linked branches, updates to the link register happen
conceptually after the read of the branch target register.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Cc: qemu-stable@nongnu.org
Message-id: 1398926097-28097-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1398926097-28097-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Like was done for AArch32 for WFE, implement both WFE and YIELD as a
yield operation. This speeds up multi-core system emulation.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Message-id: 1397588401-20366-1-git-send-email-robherring2@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
XScale defines some implementation-specific coprocessor registers
for doing cache lockdown operations. Since QEMU doesn't model a
cache no proper implementation is possible, but NOP out the
registers so that guest code like u-boot that tries to use them
doesn't crash.
Reported-by: <prqek@centrum.cz>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The test for the U bit was incorrectly inverted in the scalar case of SQXTUN.
This doesn't affect the vector case as the U bit is used to select XTN(2).
Reported-by: Hao Liu <hao.liu@arm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The smlald (and probably smlsld) instruction was doing incorrect sign
extensions of the operands amongst 64bit result calculation. The
instruction psuedo-code is:
operand2 = if m_swap then ROR(R[m],16) else R[m];
product1 = SInt(R[n]<15:0>) * SInt(operand2<15:0>);
product2 = SInt(R[n]<31:16>) * SInt(operand2<31:16>);
result = product1 + product2 + SInt(R[dHi]:R[dLo]);
R[dHi] = result<63:32>;
R[dLo] = result<31:0>;
The result calculation should be done in 64 bit arithmetic, and hence
product1 and product2 should be sign extended to 64b before calculation.
The current implementation was adding product1 and product2 together
then sign-extending the intermediate result leading to false negatives.
E.G. if product1 = product2 = 0x4000000, their sum = 0x80000000, which
will be incorrectly interpreted as -ve on sign extension.
We fix by doing the 64b extensions on both product1 and product2 before
any addition/subtraction happens.
We also fix where we were possibly incorrectly setting the Q saturation
flag for SMLSLD, which the ARM ARM specifically says is not set.
Reported-by: Christina Smith <christina.smith@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2cddb6f5a15be4ab8d2160f3499d128ae93d304d.1397704570.git.peter.crosthwaite@xilinx.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up useless 'break' statement after 'return' statement.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For system mode, we may have a 64 bit CPU which is currently executing
in AArch32 state; if we're dumping CPU state to the logs we should
therefore show the correct state for the current execution state,
rather than hardwiring it based on the type of the CPU. For consistency
with how we handle translation, we leave the 32 bit dump function
as the default, and have it hand off control to the 64 bit dump code
if we're in AArch64 mode.
Reported-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AArch64 implementation of the set_pc method needs to be updated to
handle the possibility that the CPU is in AArch32 mode; otherwise there
are weird crashes when doing interprocessing in system emulation mode
when an interrupt occurs and we fail to resynchronize the 32-bit PC
with the TB we need to execute next.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The Cortex-A15's CBAR register is actually read-only (unlike that
of the Cortex-A9). Correct our model to match the hardware.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The Cortex-A57, like most of the other ARM cores, has a CBAR
register which defines the base address of the per-CPU
peripherals. However it has a 64-bit view as well as a
32-bit view; expand the QOM reset-cbar property from UINT32
to UINT64 so this can be specified, and implement the
32-bit and 64-bit views of a 64-bit CBAR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement a subset of the Cortex-A57's implementation defined system
registers. We provide RAZ/WI or reads-as-constant/writes-ignored
implementations of the various control and syndrome reigsters.
We do not implement registers which provide direct access to and
manipulation of the L1 cache, since QEMU doesn't implement caches.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 RVBAR register, which indicates the reset
address. Since the reset address is implementation defined and
usually configurable by setting config signals in hardware, we
also provide a QOM property so it can be set at board level if
necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 address translation operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the auxiliary fault status registers AFSR0_EL1 and
AFSR1_EL1. These are present on v7 and later, and have IMPDEF
behaviour; we choose to RAZ/WI for all cores.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Many of the reginfo definitions in cp_reginfo[] use CP_ANY wildcards.
This is for a combination of reasons:
* early ARM implementations really did underdecode
* earlier versions of QEMU underdecoded and we can't tighten
this up because we don't know if guests really require this or not
* implementation convenience
For ARMv8 the architecture has tightened things up and system and
coprocessor registers are always specifically decoded. We take
advantage of this opportunity for a clean break by restricting
our CP_ANY wildcarded reginfo to pre-v8 CPUs, and providing
specifically decoded versions where necessary for v8 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
In ARMv8 the 32 bit coprocessor ID register space is tidied up to
remove the wildcarded aliases of the MIDR and the RAZ behaviour
for the unassigned space where crm = 3..7. Make sure we don't
expose thes wildcards for v8 cores. This means we need to have
a specific implementation for REVIDR, an IMPDEF register which
may be the same as the MIDR (and which we always implement as such).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The AArch64 usermode 'any' CPU type was accidentally specified
with the ARM_FEATURE_THUMB2EE bit set. This is incorrect since
ARMv8 removes Thumb2EE completely. Since we never implemented
Thumb2EE anyway having the feature bit set was fairly harmless
for user-mode, but the correct thing is to not set it at all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the ISR_EL1 register. This is actually present in
ARMv7 as well but was previously unimplemented. It is a
read-only register that indicates whether interrupts are
currently pending.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the ACTLR (auxiliary control
register). Note that QEMU internally tends to call this
AUXCR for historical reasons.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement AArch64 view of the CONTEXTIDR register.
We tighten up the condition when we flush the TLB on a CONTEXTIDR
write to avoid needlessly flushing the TLB every time on a 64
bit system (and also on a 32 bit system using LPAE, as a bonus).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
All the AArch32 ID registers are visible from AArch64
(in addition to the AArch64-specific ID_AA64* registers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For ARMv8 there are two changes to the MVFR media feature registers:
* there is a new MVFR2 which is accessible from 32 bit code
* 64 bit code accesses these via the usual sysreg instructions
rather than with a floating-point specific instruction
Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement exception handling for AArch64 EL1. Exceptions from AArch64 or
AArch32 EL0 are supported.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: fixed minor style nits; updated to match changes in
previous patches; added some of the simpler cases of
illegal-exception-return support]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Move arm_log_exception() into internals.h so we can use it from
helper-a64.c for the AArch64 exception entry code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 SPSR_EL1. For compatibility with how KVM
handles SPSRs and with the architectural mapping between AArch32
and AArch64, we put this in the banked_spsr[] array in the slot
that is used for SVC in AArch32. This means we need to extend the
array from uint32_t to uint64_t, which requires some reworking
of the 32 bit KVM save/restore code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement handling for the AArch64 SP_EL0 system register.
This holds the EL0 stack pointer, and is only accessible when
it's not being used as the stack pointer, ie when we're in EL1
and EL1 is using its own stack pointer. We also provide a
definition of the SP_EL1 register; this isn't guest visible
as a system register for an implementation like QEMU which
doesn't provide EL2 or EL3; however it is useful for ensuring
the underlying state is migrated.
We need to update the state fields in the CPU state whenever
we switch stack pointers; this happens when we take an exception
and also when SPSEL is used to change the bit in PSTATE which
indicates which stack pointer EL1 should use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Add the AArch64 ELR_EL1 register.
Note that this does not live in env->cp15: for KVM migration
compatibility we need to migrate it separately rather than
as part of the system registers, because the KVM-to-userspace
interface puts it in the struct kvm_regs rather than making
them visible via the ONE_REG ioctls.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement AArch64 views of ESR_EL1 and FAR_EL1, and make the 32 bit
DFSR, DFAR, IFAR share state with them as architecturally specified.
The IFSR doesn't share state with any AArch64 register visible at EL1,
so just rename the state field without widening it to 64 bits.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: Minor tweaks; fix some bugs involving inconsistencies between
use of offsetof() or offsetoflow32() and struct field width]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The ARM946 model currently uses the c5_data and c5_insn fields in the CPU
state struct to store the contents of its access permission registers.
This is confusing and a good source of bugs because for all the MMU-based
CPUs those fields are fault status and fault address registers, which
behave completely differently; they just happen to use the same cpreg
encoding. Split them out to use their own fields instead.
These registers are only present in PMSAv5 MPU systems (of which the
ARM946 is our only current example); PMSAv6 and PMSAv7 (which we have
no implementations of) handle access permissions differently. We name
the new state fields accordingly.
Note that this change fixes a bug where a data abort or prefetch abort
on the ARM946 would accidentally corrupt the access permission registers
because the interrupt handling code assumed the c5_data and c5_insn
fields were always fault status registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the DC ZVA instruction, which clears a block of memory.
The fast path obtains a pointer to the underlying RAM via the TCG TLB
data structure so we can do a direct memset(), with fallback to a
simple byte-store loop in the slow path.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Suppress the ID_AA64DFR0_EL1 PMUVer field, even if the CPU specific
value claims that it exists. QEMU doesn't currently implement it,
and not advertising it prevents the guest from trying to use it
and getting UNDEFs on unimplemented registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
---
This is arguably a hack, but otherwise Linux tries to prod
half a dozen PMU sysregs.
Add support for v8 page table walks. This supports stage 1 translations
for 4KB, 16KB and 64KB page sizes starting with 0 or 1 level.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: fix style nits, fold in 16/64K page support patch, use
arm_el_is_aa64() to decide whether to do 64 bit page table walk]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The current A32/T32 decoder bases its "is VFP/Neon enabled?" check
on the FPSCR.EN bit. This is correct if EL1 is AArch32, but for
an AArch64 EL1 the logic is different: it must act as if FPSCR.EN
is always set. Instead, trapping must happen according to CPACR
bits for cp10/cp11; these cover all of FP/Neon, including the
FPSCR/FPSID/MVFR register accesses which FPSCR.EN does not affect.
Add support for CPACR checks (which are also required for ARMv7,
but were unimplemented because Linux happens not to use them)
and make sure they generate exceptions with the correct syndrome.
We actually return incorrect syndrome information for cases
where FP is disabled but the specific instruction bit pattern
is unallocated: strictly these should be the Uncategorized
exception, not a "SIMD disabled" exception. This should be
mostly harmless, and the structure of the A32/T32 VFP/Neon
decoder makes it painful to put the 'FP disabled?' checks in
the right places.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Because unallocated encodings generate different exception syndrome
information from traps due to FP being disabled, we can't do a single
"is fp access disabled" check at a high level in the decode tree.
To help in catching bugs where the access check was forgotten in some
code path, we set this flag when the access check is done, and assert
that it is set at the point where we actually touch the FP regs.
This requires us to pass the DisasContext to the vec_reg_offset
and fp_reg_offset functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For the A64 instruction set, the only FP/Neon disable trap
is the CPACR FPEN bits, which may indicate "enabled", "disabled"
or "disabled for EL0". Add a bit to the AArch64 tb flags indicating
whether FP/Neon access is currently enabled and make the decoder
emit code to raise exceptions on use of FP/Neon insns if it is not.
We use a new flag in DisasContext rather than borrowing the
existing vfp_enabled flag because the A32/T32 decoder is going
to need both.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
---
I'm aware this is a rather hard to review patch; sorry.
I have done an exhaustive check that we have fp access checks
in all code paths with the aid of the assertions added in the
next patch plus the code-coverage hack patch I posted to the
list earlier.
This patch is correct as of
09e037354 target-arm: A64: Add saturating accumulate ops (USQADD/SUQADD)
which was the last of the Neon insns to be added, so assuming
no refactoring of the code it should be fine.
Set up the required syndrome information when we detect an MMU fault.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: split out from exception handling patch, tweaked to bring
in line with how we create other kinds of syndrome information]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Add new helpers exception_with_syndrome (for generating an exception
with syndrome information) and exception_uncategorized (for generating
an exception with "Unknown or Uncategorized Reason", which have a syndrome
register value of zero), and use them to generate the correct syndrome
information for exceptions which are raised directly from generated code.
This patch includes moving the A32/T32 gen_exception_insn functions
further up in the source file; they will be needed for "VFP/Neon disabled"
exception generation later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For exceptions taken to AArch64, if a coprocessor/system register
access fails due to a trap or enable bit then the syndrome information
must include details of the failing instruction (crn/crm/opc1/opc2
fields, etc). Make the decoder construct the syndrome information
at translate time so it can be passed at runtime to the access-check
helper function and used as required.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For AArch32 exceptions, the only information provided about
the cause of an exception is the individual exception type (data
abort, undef, etc), which we store in cs->exception_index. For
AArch64, the CPU provides much more detail about the cause of
the exception, which can be found in the syndrome register.
Create a set of fields in CPUARMState which must be filled in
whenever an exception is raised, so that exception entry can
correctly fill in the syndrome register for the guest.
This includes the information which in AArch32 appears in
the DFAR and IFAR (fault address registers) and the DFSR
and IFSR (fault status registers) for data aborts and
prefetch aborts, since if we end up taking the MMU fault
to AArch64 rather than AArch32 this will need to end up
in different system registers.
This patch does a refactoring which moves the setting of the
AArch32 DFAR/DFSR/IFAR/IFSR from the point where the exception
is raised to the point where it is taken. (This is no change
for cores with an MMU, retains the existing clearly incorrect
behaviour for ARM946 of trashing the MP access permissions
registers which share the c5_data and c5_insn state fields,
and has no effect for v7M because we don't implement its
MPU fault status or address registers.)
As a side effect of the cleanup we fix a bug in the AArch64
linux-user mode code where we were passing a 64 bit fault
address through the 32 bit c6_data/c6_insn fields: it now
goes via the always-64-bit exception.vaddress.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the DAIF system register which is a view of the
DAIF bits in PSTATE. To avoid needing a readfn, we widen
the daif field in CPUARMState to uint64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Currently cpu.h defines a mixture of functions and types needed by
the rest of QEMU and those needed only by files within target-arm/.
Split the latter out into a new header so they aren't needlessly
exposed further than required.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
This fixes a warning from the static code analysis (smatch).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The order of operands for the accumulate step in disas_simd_3same_int()
was reversed. This only affected the MLS instruction, since all the
other accumulating instructions in this category perform an addition
rather than a subtraction.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the saturating accumulate operations USQADD and SUQADD
to the A64 instruction set. This completes coverage of A64 Neon.
These operations (which are unsigned + signed -> signed and
signed + unsigned -> unsigned) don't exist in the A32/T32
instruction set, so require a complete new set of helper functions.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This mostly re-uses the existing NEON helpers with an additional two for
the 64 bit case. I also took the opportunity to add TCG_CALL_NO_RWG
options to the helpers as they don't modify globals (saturation flags
are in the CPU Environment).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This adds support for [UF]RSQRTE instructions. It utilises the existing
NEON helpers with some changes. The changes include an explicit passing
of fpstatus (so the correct one is used between arm32 and aarch64),
denormilzation, more correct error handling and also proper scaling of
the fraction going into the estimate.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-25-git-send-email-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the FCVTXN operation, which does a narrowing fp precision
conversion using the "round to odd" (von Neumann) mode. This can
conveniently be implemented as "do operation using round to zero;
then set the LSB of the mantissa to 1 if the Inexact flag was set".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-24-git-send-email-peter.maydell@linaro.org
This completes the set of integer narrowing saturating ops including:
SQXTN, SQXTN2
SQXTUN, SQXTUN2
UQXTN, UQXTN2
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-23-git-send-email-peter.maydell@linaro.org
Move the handle_2misc_narrow() function up the file so that it can
be called from disas_simd_scalar_two_reg_misc().
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-22-git-send-email-peter.maydell@linaro.org
Implement URECPE and FRECPE instructions in both scalar and vector forms.
The actual reciprocal estimate function is shared with the A32/T32 Neon
code. However in A64 we aren't using the Neon "standard FPSCR value"
so extra checks are necessary to handle non-squashed denormal inputs
which can never happen for A32/T32. Calling conventions for the helpers
are thus modified to pass the fpst directly; we mark the helpers as
TCG_CALL_NO_RWG since we're changing the declarations anyway.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-21-git-send-email-peter.maydell@linaro.org
Implement FCVTZS and FCVTZU in the shift-imm and scalar-shift-imm
categories; this completes the implementation of those two groups.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-19-git-send-email-peter.maydell@linaro.org
Implement the saturating left shift instructions SQSHL, SQSHLU
and UQSHL for the scalar-shift-imm and shift-imm categories.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-18-git-send-email-peter.maydell@linaro.org
Implement the FRINT* round-to-integral operations from
the 2-reg-misc category.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-16-git-send-email-peter.maydell@linaro.org
These are fairly simple exponent only estimation functions using helpers.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-14-git-send-email-peter.maydell@linaro.org
Add the remaining unsupported opcodes to the decode switches
for the shift-imm and scalar shift-imm categories so we can
see what is still to be implemented.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-13-git-send-email-peter.maydell@linaro.org
Implement FCVTL, the only instruction in the 2-reg-misc group
which widens from size to 2*size elements.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-12-git-send-email-peter.maydell@linaro.org
Implement FCVTN (narrowing fp-to-fp conversions) from the SIMD
2-reg-misc category.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-11-git-send-email-peter.maydell@linaro.org
Implement the floating-point-to-integer conversion instructions
FCVT[NMAPZ][SU] in the 2-reg-misc and scalar-2-reg-misc
categories.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-10-git-send-email-peter.maydell@linaro.org
Implement the SHLL and SHLL2 instructions from the 2-reg-misc
category.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-9-git-send-email-peter.maydell@linaro.org
Implement the SADDLP, UADDLP, SADALP and UADALP instructions
in the SIMD 2-reg misc category.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-8-git-send-email-peter.maydell@linaro.org
This implements the remaining [US][Q][R]SHR[U][N][2] opcodes, which are
saturating and narrowing shift right operations. These are used in
things like libav. Note signed shifts can have an "unsigned" saturating
narrow operation which will floor negative values.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1394822294-14837-7-git-send-email-peter.maydell@linaro.org
[PMM: Added the scalar encodings, style tweaks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the CLS, CLZ operations in the 2-reg-misc category.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-6-git-send-email-peter.maydell@linaro.org
Implement FSQRT in the two-reg-misc category.
GCC uses this instruction form.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-5-git-send-email-peter.maydell@linaro.org
This adds the remaining [US]CVTF operations to the SIMD
shift-immediate, scalar-shift-immediate, two-reg-misc and
scalar-two-reg-misc groups of opcodes.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1394822294-14837-4-git-send-email-peter.maydell@linaro.org
[PMM: added scalar 2-misc and scalar-shift-imm encodings]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
rn == 31 always means SP (not XZR) whether an add_sub_ext
instruction is setting the flags or not; only rd has behaviour
dependent on whether we are setting flags.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-3-git-send-email-peter.maydell@linaro.org
Implement the PMULL instruction; this is the last unimplemented insn
in the three-reg-diff group.
Note that PMULL with size 3 is considered part of the AES part
of the crypto extensions (see the ID_AA64ISAR0_EL1 register definition
in the v8 ARM ARM), so it isn't necessary to burn an extra feature
bit on it, even though we're using more feature bits than a single
"crypto extension present/not present" toggle.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394822294-14837-2-git-send-email-peter.maydell@linaro.org
Now that the PMCR writefn makes timer accesses, its reginfo needs
the ARM_CP_IO flag, so that icount mode works correctly. (Fixes
the bug accidentally introduced in commit 7c2cb42b).
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1394908291-16546-1-git-send-email-peter.maydell@linaro.org
Codespell found and fixed these new typos:
* doesnt -> doesn't
* funtion -> function
* perfomance -> performance
* remaing -> remaining
A coding style issue (line too long) was fixed manually.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Most targets were using offsetof(CPUFooState, breakpoints) to determine
how much of CPUFooState to clear on reset. Use the next field after
CPU_COMMON instead, if any, or sizeof(CPUFooState) otherwise.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
All targets using it gain the ability to set -cpu name,key=value,...
options via the default TYPE_CPU CPUClass::parse_features() implementation.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Default to false.
Tidy variable naming and inline cast uses while at it.
Tested-by: Jia Liu <proljc@gmail.com> (or32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commits ab1da85791,
fdfba1a298,
2c17449b30 added usages of ENV_GET_CPU()
macro to target-specific code.
Use arm_env_get_cpu() instead and enforce separating variable
declarations.
Cc: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Implement WFE to yield our timeslice to the next CPU.
This avoids slowdowns in multicore configurations caused
by one core busy-waiting on a spinlock which can't possibly
be unlocked until the other core has an opportunity to run.
This speeds up my test case A15 dual-core boot by a factor
of three (though it is still four or five times slower than
a single-core boot).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1393339545-22111-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tested-by: Rob Herring <rob.herring@linaro.org>
Fixes a build error when these are different, e.g. x32.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1394043257-4800-1-git-send-email-rth@twiddle.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 4cc35614a moved the exception mask bits out of env->uncached_cpsr
and into env->daif. However the env->daif contents are AArch64 style
mask bits, which include not just the AArch32 AIF bits but also the
new D bit (masks debug exceptions). This means that when reconstructing
the AArch32 CPSR value we must not allow the D bit in env->daif to get
into the CPSR, because the corresponding bit in the CPSR is E, the
endianness bit.
This bug didn't affect execution under TCG because we don't implement
endianness-swapping and so simply ignored the E bit; however it meant
that kernel booting under KVM failed, because KVM does honour the E bit.
Reported-by: Alexey Ignatov <lexszero@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for AArch32 CRC32 and CRC32C instructions added in ARMv8
and add a CPU feature flag to enable these instructions.
The CRC32-C implementation used is the built-in qemu implementation
and The CRC-32 implementation is from zlib. This requires adding zlib
to LIBS to ensure it is linked for the linux-user binary.
Signed-off-by: Will Newton <will.newton@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1393411566-24104-3-git-send-email-will.newton@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are various situations where we need to behave differently
depending on whether a given exception level is in AArch64 or
AArch32 state. The state of the current exception level is stored
in env->aarch64, but there's no equivalent guest-visible architected
state bits for the status of the exception levels "above" the
current one which may still affect execution. At the moment we
only support EL1 (ie no EL2 or EL3) and insist that AArch64
capable CPUs run with EL1 in AArch64 state, but these may change
in the future, so abstract out the "what state is this?" check
into a utility function which can be enhanced later if necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the CPACR. The AArch64
CPACR is defined to have a lot of RES0 bits, but since
the architecture defines that RES0 bits may be implemented
as reads-as-written and we know that a v8 CPU will have
no registered coprocessors for cp0..cp13 we can safely
implement the whole register this way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the MSR (immediate) instructions, which can update the
PSTATE SP and DAIF fields.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
To avoid complication in code that otherwise would not need to
care about whether EL1 is AArch32 or AArch64, we should store
the interrupt mask bits (CPSR.AIF in AArch32 and PSTATE.DAIF
in AArch64) in one place consistently regardless of EL1's mode.
Since AArch64 has an extra enable bit (D for debug exceptions)
which isn't visible in AArch32, this means we need to keep
the enables in env->pstate. (This is also consistent with the
general approach we're taking that we handle 32 bit CPUs as
being like AArch64/ARMv8 CPUs but which only run in 32 bit mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the WFI instruction for A64; this just involves wiring
up the instruction, and adding a gen_a64_set_pc_im() which was
accidentally omitted from the A64 decoder top loop.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Emit the correct MMU index information for loads and stores from
A64 code, rather than hardwiring it to "always kernel mode",
by storing the exception level in the TB flags, and make
cpu_mmu_index() return the right answer when the CPU is in
AArch64 mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Define a dummy version of the AArch64 OSLAR_EL1 system register
which just ignores writes. Linux will always write to this (it
is the OS lock used for debugging), but we don't support debug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
In AArch64 the breakpoint and watchpoint registers are mandatory, so the
kernel always accesses them on bootup. Implement dummy versions, which
read as written but have no actual effect.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64-specific ID and feature registers. Although
many of these are currently not used by the architecture (and so
always zero for all implementations), we define the full set of
fields in the ARMCPU struct for symmetry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 MPIDR system register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TTBR* registers. For v7 these were already 64 bits
to handle LPAE, but implemented as two separate uint32_t fields.
Combine them into a single uint64_t which can be used for all purposes.
Since this requires touching every use, take the opportunity to rename
the field to the architectural name.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the A64 view of the VBAR system register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TCR_EL1, which is the 64 bit view of
the AArch32 TTBCR. (The uses of the bits in the register are
completely different, but in any given situation the CPU will
always interpret them one way or the other. In fact for QEMU EL1
is always 64 bit, but we share the state field because this
is the correct mapping to permit a future implementation of EL2.)
We also make the AArch64 view the 'master' as far as migration
and reset is concerned.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the system control register SCTLR_EL1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 memory attribute registers. Since QEMU doesn't
model caches it does not need to care about memory attributes at all,
and we can simply make these read-as-written.
We did not previously implement the AArch32 versions of the MAIR
registers, which went unnoticed because of the overbroad TLB_LOCKDOWN
reginfo definition; provide them now to keep the 64<->32 register
relationship clear.
We already provided AMAIR registers for 32 bit as simple RAZ/WI;
extend that to provide a 64 bit RAZ/WI AMAIR_EL1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
We don't support letting the guest do debug, but Linux prods the
monitor debug system control register anyway, so implement a dummy
RAZ/WI version.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 TLB invalidate operations. This is
the full set of TLBI ops defined for a CPU which doesn't
implement EL2 or EL3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement all the AArch64 cache invalidate and clean ops
(which are all NOPs since QEMU doesn't emulate the cache).
The only remaining unimplemented cache op is DC ZVA.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 view of the MIDR system register
(for AArch64 it is a simple constant, unlike the complicated
mess that TI925 imposes on the 32-bit view).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Make the cache ID system registers (CLIDR, CSSELR, CCSIDR, CTR)
visible to AArch64. These are mostly simple 64-bit extensions of the
existing 32 bit system registers and so can share reginfo definitions.
CTR needs to have a split definition, but we can clean up the
temporary user-mode implementation in favour of using the CPU-specified
reset value, and implement the system-mode-required semantics of
restricting its EL0 accessibility if SCTLR.UCT is not set.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The raw read and write functions were using the ARM_CP_64BIT flag in
ri->type to determine whether to treat the register's state field as
uint32_t or uint64_t; however AArch64 register info structs don't use
that flag. Abstract out the "how big is the field?" test into a
function and fix it to work for AArch64 registers. For this to work
we must ensure that the reginfo structs put into the hashtable have
the correct state field for their use, not the placeholder STATE_BOTH.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support creating the ARM vgic device through the device control API and
setting the base address for the distributor and cpu interfaces in KVM
VMs using this API.
Because the older KVM_CREATE_IRQCHIP interface needs the irq chip to be
created prior to creating the VCPUs, we first test if we can use the
device control API in kvm_arch_irqchip_create (using the test flag from
the device control API). If we cannot, it means we have to fall back to
KVM_CREATE_IRQCHIP and use the older ioctl at this point in time. If
however, we can use the device control API, we don't do anything and
wait until the arm_gic_kvm driver initializes and let that use the
device control API.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-5-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In ARMv5 level 2 page table descriptors, each 4K or 64K page is split into
four subpages, each of which can have different access permission settings,
which are specified by four two-bit fields in the l2 descriptor. A
long-standing cut-and-paste error meant we were using the wrong bits in
the virtual address to select the access-permission field for 4K pages.
The error has presumably not been noticed before because most guests don't
make use of the ability to set the access permissions differently for
each 1K subpage: if the guest gives the whole page the same access
permissions it doesn't matter which of the 4 AP fields we select.
(The whole issue is irrelevant for ARMv7 CPUs anyway because subpages
aren't supported there.)
Reported-by: Vivek Rai <Vivek.Rai@emulex.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1392667690-8731-1-git-send-email-peter.maydell@linaro.org
Correct some obviously nonsensical bit manipulation spotted by Coverity
when constructing the short-form PAR value for ATS operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1392659525-8335-1-git-send-email-peter.maydell@linaro.org
Implement the unprivileged load and store instructions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement the narrowing three-reg-diff operations: ADDHN,
RADDHN, SUBHN and RSUBHN.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement the wide three-reg-different operations:
SADDW, UADDW, SSUBW and USUBW.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Add the remainder of the 64x64->128 operations in the three-reg-diff
category except for PMULL, PMULL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The opcode switch in disas_simd_three_reg_diff() is missing the
customary comments indicating which cases correspond to which
instructions. Add them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
System mode store-exclusive use a different code path to usermode ones;
implement this missing code, in a similar way to the 32 bit version.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The write_raw_cp_reg's value argument should be a uint64_t, since
that's what all its callers hand it and what all the functions it
calls take. A (harmless) typo meant we were accidentally declaring
it as int64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The read_raw_cp_reg and write_raw_cp_reg functions can now never
fail (in fact they should never have failed previously unless
there was a bug in a reginfo that meant no raw accessor was
provided for a might-trap register). This allows us to clean up
their prototypes so the write function returns void and the
read function returns the value read, which in turn lets us
simplify the callers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Now that cpreg read and write functions can't fail and throw an
exception, we can remove the code from the translator that synchronises
the guest PC in case an exception is thrown.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All cpreg read and write functions now return 0, so we can clean up
their prototypes:
* write functions return void
* read functions return the value rather than taking a pointer
to write the value to
This is a fairly mechanical change which makes only the bare
minimum set of changes to the callers of read and write functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Convert the remaining miscellaneous cases of reginfo read/write
functions returning EXCP_UDEF to use an accessfn instead:
TEEHBR, and the ATS address-translation operations.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the reginfo structs for the generic timer registers
to use access functions rather than returning EXCP_UDEF from
their read handlers. In some cases this allows us to remove
a read handler completely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Convert the performance monitor reginfo definitions to use
an accessfn rather than returning EXCP_UDEF from read and
write functions. This also allows us to fix a couple of XXX
cases where we weren't imposing the access restrictions on
RAZ/WI or constant registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several of the system registers handled via the ARMCPRegInfo
mechanism have access trap control bits controlling whether the
registers are accessible to lower privilege levels. Replace
the existing mechanism (allowing the read and write functions
to return EXCP_UDEF if access is denied) with a dedicated
"check access rights" function pointer in the ARMCPRegInfo.
This will allow us to simplify some of the register definitions,
which no longer need read/write functions purely to handle
the access checks.
We take the opportunity to define the return value from the
access checking function in a way that allows us to set the
correct exception syndrome information for exceptions taken
to AArch64 (which may need to distinguish access failures due
to a configurable trap or enable from other kinds of access
failure).
This commit defines the new mechanism but does not move any
of the registers across to use it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The ARM946 has 8 PRBS (protection region base and size) registers.
Currently we implement these with a CP_ANY reginfo; however this
underdecodes (since there are 16 possible values of CRm but only
8 registers) and we catch the invalid values in the read and
write functions. However this causes issues with migration since
we only migrate the first of a wildcard register set, so we only
migrate c6_region[0]. It also makes it awkward to pull reginfo
access checks out into their own function.
Avoid all these problems by just defining separate reginfo structs
for each of the 8 registers; this also lets us avoid having any
read or write functions and will result in more efficient direct
field accesses from generated code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Log guest attempts to access unimplemented system registers via
the LOG_UNIMP reporting mechanism (for both the 32 bit and 64 bit
instruction sets). This is particularly useful for debugging
problems where the guest is trying to use a system register that
QEMU doesn't implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Remove the 'struct sr' from ARMCPUState -- it isn't actually used and is
a hangover from the original separate system register implementation used
by the SuSE linux-user-mode-only AArch64 target.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The SCTLR bits S and R (8 and 9) only exist in ARMv6 and earlier.
In ARMv7 these bits RAZ, and in ARMv8 they are reassigned. Guard
the use of them in check_ap() so that we don't get incorrect results
for ARMv8 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
The SCTLR is full of bits for enabling or disabling various things, and so
there are many places in the code which check if certain bits are set.
Define some named constants for the SCTLR bits so these checks are easier
to read.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend the set of CPUs for which we provide a QEMU_KVM_ARM_TARGET_*
constant to include all the ones currently supported by the kernel
headers we are using.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the remaining instructions in the SIMD 3-reg-same
and scalar-3-reg-same groups: FMULX, FRECPS, FRSQRTS, FACGE,
FACGT, FMLA and FMLS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Add support for the floating-point pairwise operations
FADDP, FMAXP, FMAXNMP, FMINP and FMINNMP. To do this we use the
code which was previously handling only integer pairwise operations,
and push the integer-specific decode and handling of unallocated
cases up one level in the call tree, so we can also call it from
the floating-point section of the decoder.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This adds all forms of the SIMD floating point and set instructions:
FCM(GT|GE|EQ|LE|LT)
Most of the heavy lifting is done by either the existing neon helpers or
some new helpers for the 64bit double cases. Most of the code paths are
common although the 2misc versions are a little special as they compare
against zero.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
[PMM: fixed some minor bugs, added the 2-misc-scalar encoding]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement the scalar three different instruction group:
it only has three instructions in it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement the SIMD scalar indexed instructions. The encoding
here is nearly identical to the vector indexed grouping, so
we combine the two.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement the 'long' operations in the vector x indexed
element category.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Implement all the SIMD vector x indexed element instructions
in the subcategory which are not 'long' ops.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Use libvixl to implement disassembly output in debug
logs for A64, for use with both AArch64 hosts and targets.
Signed-off-by: Claudio Fontana <claudio.fontana@linaro.org>
[PMM:
* added support for target disassembly
* switched to custom QEMUDisassembler so the output format
matches what QEMU expects
* make sure we correctly fall back to "just print hex"
if we didn't build the AArch64 disassembler because of
lack of a C++ compiler
* rename from 'aarch64' to 'arm-a64' because this is a
disassembler for the A64 instruction set
* merge aarch64.c and aarch64-cxx.cc into one C++ file
* simplify the aarch64.c<->aarch64-cxx.cc interface]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
