The Linux spi-imx driver does not work on QEMU. The reason is that the
state of m25p80 loops in STATE_READING_DATA state after receiving
RDSR command, the new command is ignored. Before sending a new command,
CS line should be pulled high to make the state of m25p80 back to IDLE.
Currently the SPI flash CS line is connected to the SPI controller, but
on the real board, it's connected to GPIO3_19. This matches the ecspi1
device node in the board dts.
ecspi1 node in imx6qdl-sabrelite.dtsi:
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash: m25p80@0 {
compatible = "sst,sst25vf016b", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
Should connect the SSI_GPIO_CS to GPIO3_19 when adding a spi-nor to
spi1 on sabrelite machine.
Verified this patch on Linux v5.14.
Logs:
# echo "01234567899876543210" > test
# mtd_debug erase /dev/mtd0 0x0 0x1000
Erased 4096 bytes from address 0x00000000 in flash
# mtd_debug write /dev/mtdblock0 0x0 20 test
Copied 20 bytes from test to address 0x00000000 in flash
# mtd_debug read /dev/mtdblock0 0x0 20 test_out
Copied 20 bytes from address 0x00000000 in flash to test_out
# cat test_out
01234567899876543210#
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210927142825.491-1-xchengl.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for ZynqMP eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=3,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 768 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-9-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Xilinx ZynqMP Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=2,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-8-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=1,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 3072 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-7-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=0,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-6-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 SoC uses Cortex-A7 cores which support virtualization.
However, today we are configuring QEMU to use HVC as PSCI conduit.
That means HVC calls get trapped into QEMU instead of the guest's own
emulated CPU and thus break the guest's ability to execute virtualization.
Fix this by moving to SMC as conduit, freeing up HYP completely to the VM.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20210920203931.66527-1-agraf@csgraf.de
Fixes: 740dafc0ba ("hw/arm: add Allwinner H3 System-on-Chip")
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The various MPS2 boards implemented in mps2.c have multiple I2C
buses: a bus dedicated to the audio configuration, one for the LCD
touchscreen controller, and two which are connected to the external
Shield expansion connector. Mark the buses which are used only for
board-internal devices as 'full' so that if the user creates i2c
devices on the commandline without specifying a bus name then they
will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-5-peter.maydell@linaro.org
The various MPS2 boards have multiple I2C buses: typically a bus
dedicated to the audio configuration, one for the LCD touchscreen
controller, one for a DDR4 EEPROM, and two which are connected to the
external Shield expansion connector. Mark the buses which are used
only for board-internal devices as 'full' so that if the user creates
i2c devices on the commandline without specifying a bus name then
they will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-4-peter.maydell@linaro.org
The mps2-tz boards use a data-driven structure to create the devices
that sit behind peripheral protection controllers. Currently the
functions which create these devices are passed an 'opaque' pointer
which is always the address within the machine struct of the device
to create, and some "all devices need this" information like irqs and
addresses.
If a specific device needs more information than this, it is
currently not possible to pass that through from the PPCInfo
data structure. Add support for passing an extra data parameter,
so that we can more flexibly handle the needs of specific
device types. To provide some type-safety we make this extra
parameter a pointer to a union (which initially has no members).
In particular, we would like to be able to indicate which of the
i2c controllers are for on-board devices only and which are
connected to the external 'shield' expansion port; a subsequent
patch will use this mechanism for that purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-3-peter.maydell@linaro.org
Included creation of ITS as part of virt platform GIC
initialization. This Emulated ITS model now co-exists with kvm
ITS and is enabled in absence of kvm irq kernel support in a
platform.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-9-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All the devices that used to use system_clock_scale have now been
converted to use Clock inputs instead, so the global is no longer
needed; remove it and all the code that sets it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210812093356.1946-26-peter.maydell@linaro.org
The stellaris-gptm timer currently uses system_clock_scale for one of
its timer modes where the timer runs at the CPU clock rate. Make it
use a Clock input instead.
We don't try to make the timer handle changes in the clock frequency
while the downcounter is running. This is not a change in behaviour
from the previous system_clock_scale implementation -- we will pick
up the new frequency only when the downcounter hits zero. Handling
dynamic clock changes when the counter is running would require state
that the current gptm implementation doesn't have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-25-peter.maydell@linaro.org
The implementation of the Stellaris general purpose timer module
device stellaris-gptm is currently in the same source file as the
board model. Split it out into its own source file in hw/timer.
Apart from the new file comment headers and the Kconfig and
meson.build changes, this is just code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-24-peter.maydell@linaro.org
Fix the code style issues in the Stellaris general purpose timer
module code, so that when we move it to a different file in a
following patch checkpatch doesn't complain.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-23-peter.maydell@linaro.org
Wire up the refclk for the msf2 SoC. This SoC runs the refclk at a
frequency which is programmably either /4, /8, /16 or /32 of the main
CPU clock. We don't currently model the register which allows the
guest to set the divisor, so implement the refclk as a fixed /32 of
the CPU clock (which is the value of the divisor at reset).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-21-peter.maydell@linaro.org
Instead of passing the MSF2 SoC an integer property specifying the
CPU clock rate, pass it a Clock instead. This lets us wire that
clock up to the armv7m object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-20-peter.maydell@linaro.org
In the realize method of the msf2-soc SoC object, we call g_new() to
create new MemoryRegion objects for the nvm, nvm_alias, and sram.
This is unnecessary; make these MemoryRegions member fields of the
device state struct instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-19-peter.maydell@linaro.org
Connect the sysclk to the armv7m object. This board's SoC does not
connect up the systick reference clock, so we don't need to connect a
refclk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-18-peter.maydell@linaro.org
Currently the stellaris_sys_init() function creates the
TYPE_STELLARIS_SYS object, sets its properties, realizes it, maps its
MMIO region and connects its IRQ. In order to support wiring the
sysclk up to the armv7m object, we need to split this function apart,
because to connect the clock output of the STELLARIS_SYS object to
the armv7m object we need to create the STELLARIS_SYS object before
the armv7m object, but we can't wire up the IRQ until after we've
created the armv7m object.
Remove the stellaris_sys_init() function, and instead put the
create/configure/realize parts before we create the armv7m object and
the mmio/irq connection parts afterwards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-17-peter.maydell@linaro.org
Wire up the sysclk input to the armv7m object.
Strictly this SoC should not have a systick device at all, but our
armv7m container object doesn't currently support disabling the
systick device. For the moment, add a TODO comment, but note that
this is why we aren't wiring up a refclk (no need for one).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-16-peter.maydell@linaro.org
Delete the trailing blank line at the end of the source file.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-15-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f405 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the netduinoplus2 board where the
systick reference clock was running at 1MHz rather than 21MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-14-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f205 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the netduino2 board where the systick
reference clock was running at 1MHz rather than 15MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-13-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f100 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the stm32vldiscovery board where the
systick reference clock was running at 1MHz rather than 3MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-12-peter.maydell@linaro.org
In the realize methods of the stm32f100 and stm32f205 SoC objects, we
call g_new() to create new MemoryRegion objects for the sram, flash,
and flash_alias. This is unnecessary (and leaves open the
possibility of leaking the allocations if we exit from realize with
an error). Make these MemoryRegions member fields of the device
state struct instead, as stm32f405 already does.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-11-peter.maydell@linaro.org
Connect up the armv7m clocks on the mps2-an385/386/500/511.
Connect up the armv7m object's clocks on the MPS boards defined in
mps2.c. The documentation for these FPGA images doesn't specify what
systick reference clock is used (if any), so for the moment we
provide a 1MHz refclock, which will result in no behavioural change
from the current hardwired 1MHz clock implemented in
armv7m_systick.c:systick_scale().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-9-peter.maydell@linaro.org
Wire up the cpuclk for the systick devices to the SSE object's
existing mainclk clock.
We do not wire up the refclk because the SSE subsystems do not
provide a refclk. (This is documented in the IoTKit and SSE-200
TRMs; the SSE-300 TRM doesn't mention it but we assume it follows the
same approach.) When we update the systick device later to honour "no
refclk connected" this will fix a minor emulation inaccuracy for the
SSE-based boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-8-peter.maydell@linaro.org
Create input clocks on the armv7m container object which pass through
to the systick timers, so that users of the armv7m object can specify
the clocks being used.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-7-peter.maydell@linaro.org
Instead of having the NVIC device provide a single sysbus memory
region covering the whole of the "System PPB" space, which implements
the default behaviour for unimplemented ranges and provides the NS
alias window to the sysregs as well as the main sysreg MR, move this
handling to the container armv7m device. The NVIC now provides a
single memory region which just implements the system registers.
This consolidates all the handling of "map various devices in the
PPB" into the armv7m container where it belongs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-4-peter.maydell@linaro.org
There's no particular reason why the NVIC should be owning the
SysTick device objects; move them into the ARMv7M container object
instead, as part of consolidating the "create the devices which are
built into an M-profile CPU and map them into their architected
locations in the address space" work into one place.
This involves temporarily creating a duplicate copy of the
nvic_sysreg_ns_ops struct and its read/write functions (renamed as
v7m_sysreg_ns_*), but we will delete the NVIC's copy of this code in
a subsequent patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-3-peter.maydell@linaro.org
Currently we implement the RAS register block within the NVIC device.
It isn't really very tightly coupled with the NVIC proper, so instead
move it out into a sysbus device of its own and have the top level
ARMv7M container create it and map it into memory at the right
address.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-2-peter.maydell@linaro.org
Add -cpu a64fx to use A64FX processor when -machine virt option is
specified. In addition, add a64fx to the Supported guest CPU types
in the virt.rst document.
Signed-off-by: Shuuichirou Ishii <ishii.shuuichir@fujitsu.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 6.2 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the raspi2/raspi3 machine aliases,
deprecated since commit 155e1c82ed.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210827060815.2384760-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the CPU realize function will fail cleanly if we ask for EL3
when KVM is enabled, we don't need to check for errors explicitly in
the virt board code. The reported message is slightly different;
it is now:
qemu-system-aarch64: Cannot enable KVM when guest CPU has EL3 enabled
instead of:
qemu-system-aarch64: mach-virt: KVM does not support Security extensions
We don't delete the MTE check because there the logic is more
complex; deleting the check would work but makes the error message
less helpful, as it would read:
qemu-system-aarch64: MTE requested, but not supported by the guest CPU
instead of:
qemu-system-aarch64: mach-virt: KVM does not support providing MTE to the guest CPU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210816135842.25302-4-peter.maydell@linaro.org
The SoC realize can fail for legitimate reasons, because it propagates
errors up from CPU realize, which in turn can be provoked by user
error in setting commandline options. Use error_fatal so we report
the error message to the user and exit, rather than asserting
via error_abort.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210816135842.25302-2-peter.maydell@linaro.org
Since commit
36b79e3219 ("hw/acpi/Kconfig: Add missing Kconfig dependencies (build error)"),
ACPI_MEMORY_HOTPLUG and ACPI_NVDIMM is implicitly turned on when
ACPI_HW_REDUCED is selected. ACPI_HW_REDUCED is already enabled. No need to
turn on ACPI_MEMORY_HOTPLUG or ACPI_NVDIMM explicitly. This is a minor cleanup.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210819162637.518507-1-ani@anisinha.ca
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simplify by always passing a MemoryRegion property to the device.
Doing so we can move the AddressSpace field to the device struct,
removing need for heap allocation.
Update the Xilinx ZynqMP / Versal SoC models to pass the default
system memory instead of a NULL value.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210819163422.2863447-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simplify by always passing a MemoryRegion property to the device.
Doing so we can move the AddressSpace field to the device struct,
removing need for heap allocation.
Update the Xilinx ZynqMP SoC model to pass the default system
memory instead of a NULL value.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210819163422.2863447-4-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we link QOM object (a) as a property of QOM object (b),
we must set the property *before* (b) is realized.
Move QSPI realization *after* QSPI DMA.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210819163422.2863447-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SBSA_GWDT enum value conflicts with the SBSA_GWDT() QOM type
checking helper, preventing us from using a OBJECT_DEFINE* or
DEFINE_INSTANCE_CHECKER macro for the SBSA_GWDT() wrapper.
If I understand the SBSA 6.0 specification correctly, the signal
being connected to IRQ 16 is the WS0 output signal from the
Generic Watchdog. Rename the enum value to SBSA_GWDT_WS0 to be
more explicit and avoid the name conflict.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20210806023119.431680-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add property memory region which can connect with IOMMU region to support SMMU translate.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 4C23C17B8E87E74E906A25A3254A03F4FA1FEC31@SHASXM03.verisilicon.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate SAI1/2/3 and ASRC as unimplemented devices to avoid random
Linux kernel crashes, such as
Unhandled fault: external abort on non-linefetch (0x808) at 0xd1580010
pgd = (ptrval)
[d1580010] *pgd=8231b811, *pte=02034653, *ppte=02034453
Internal error: : 808 [#1] SMP ARM
...
[<c095e974>] (regmap_mmio_write32le) from [<c095eb48>] (regmap_mmio_write+0x3c/0x54)
[<c095eb48>] (regmap_mmio_write) from [<c09580f4>] (_regmap_write+0x4c/0x1f0)
[<c09580f4>] (_regmap_write) from [<c095837c>] (_regmap_update_bits+0xe4/0xec)
[<c095837c>] (_regmap_update_bits) from [<c09599b4>] (regmap_update_bits_base+0x50/0x74)
[<c09599b4>] (regmap_update_bits_base) from [<c0d3e9e4>] (fsl_asrc_runtime_resume+0x1e4/0x21c)
[<c0d3e9e4>] (fsl_asrc_runtime_resume) from [<c0942464>] (__rpm_callback+0x3c/0x108)
[<c0942464>] (__rpm_callback) from [<c0942590>] (rpm_callback+0x60/0x64)
[<c0942590>] (rpm_callback) from [<c0942b60>] (rpm_resume+0x5cc/0x808)
[<c0942b60>] (rpm_resume) from [<c0942dfc>] (__pm_runtime_resume+0x60/0xa0)
[<c0942dfc>] (__pm_runtime_resume) from [<c0d3ecc4>] (fsl_asrc_probe+0x2a8/0x708)
[<c0d3ecc4>] (fsl_asrc_probe) from [<c0935b08>] (platform_probe+0x58/0xb8)
[<c0935b08>] (platform_probe) from [<c0933264>] (really_probe.part.0+0x9c/0x334)
[<c0933264>] (really_probe.part.0) from [<c093359c>] (__driver_probe_device+0xa0/0x138)
[<c093359c>] (__driver_probe_device) from [<c0933664>] (driver_probe_device+0x30/0xc8)
[<c0933664>] (driver_probe_device) from [<c0933c88>] (__driver_attach+0x90/0x130)
[<c0933c88>] (__driver_attach) from [<c0931060>] (bus_for_each_dev+0x78/0xb8)
[<c0931060>] (bus_for_each_dev) from [<c093254c>] (bus_add_driver+0xf0/0x1d8)
[<c093254c>] (bus_add_driver) from [<c0934a30>] (driver_register+0x88/0x118)
[<c0934a30>] (driver_register) from [<c01022c0>] (do_one_initcall+0x7c/0x3a4)
[<c01022c0>] (do_one_initcall) from [<c1601204>] (kernel_init_freeable+0x198/0x22c)
[<c1601204>] (kernel_init_freeable) from [<c0f5ff2c>] (kernel_init+0x10/0x128)
[<c0f5ff2c>] (kernel_init) from [<c010013c>] (ret_from_fork+0x14/0x38)
or
Unhandled fault: external abort on non-linefetch (0x808) at 0xd19b0000
pgd = (ptrval)
[d19b0000] *pgd=82711811, *pte=308a0653, *ppte=308a0453
Internal error: : 808 [#1] SMP ARM
...
[<c095e974>] (regmap_mmio_write32le) from [<c095eb48>] (regmap_mmio_write+0x3c/0x54)
[<c095eb48>] (regmap_mmio_write) from [<c09580f4>] (_regmap_write+0x4c/0x1f0)
[<c09580f4>] (_regmap_write) from [<c0959b28>] (regmap_write+0x3c/0x60)
[<c0959b28>] (regmap_write) from [<c0d41130>] (fsl_sai_runtime_resume+0x9c/0x1ec)
[<c0d41130>] (fsl_sai_runtime_resume) from [<c0942464>] (__rpm_callback+0x3c/0x108)
[<c0942464>] (__rpm_callback) from [<c0942590>] (rpm_callback+0x60/0x64)
[<c0942590>] (rpm_callback) from [<c0942b60>] (rpm_resume+0x5cc/0x808)
[<c0942b60>] (rpm_resume) from [<c0942dfc>] (__pm_runtime_resume+0x60/0xa0)
[<c0942dfc>] (__pm_runtime_resume) from [<c0d4231c>] (fsl_sai_probe+0x2b8/0x65c)
[<c0d4231c>] (fsl_sai_probe) from [<c0935b08>] (platform_probe+0x58/0xb8)
[<c0935b08>] (platform_probe) from [<c0933264>] (really_probe.part.0+0x9c/0x334)
[<c0933264>] (really_probe.part.0) from [<c093359c>] (__driver_probe_device+0xa0/0x138)
[<c093359c>] (__driver_probe_device) from [<c0933664>] (driver_probe_device+0x30/0xc8)
[<c0933664>] (driver_probe_device) from [<c0933c88>] (__driver_attach+0x90/0x130)
[<c0933c88>] (__driver_attach) from [<c0931060>] (bus_for_each_dev+0x78/0xb8)
[<c0931060>] (bus_for_each_dev) from [<c093254c>] (bus_add_driver+0xf0/0x1d8)
[<c093254c>] (bus_add_driver) from [<c0934a30>] (driver_register+0x88/0x118)
[<c0934a30>] (driver_register) from [<c01022c0>] (do_one_initcall+0x7c/0x3a4)
[<c01022c0>] (do_one_initcall) from [<c1601204>] (kernel_init_freeable+0x198/0x22c)
[<c1601204>] (kernel_init_freeable) from [<c0f5ff2c>] (kernel_init+0x10/0x128)
[<c0f5ff2c>] (kernel_init) from [<c010013c>] (ret_from_fork+0x14/0x38)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20210810160318.87376-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the user provides both a BIOS/firmware image and also a guest
kernel filename, arm_setup_firmware_boot() will pass the
kernel image to the firmware via the fw_cfg device. However we
weren't checking whether there really was a fw_cfg device present,
and if there wasn't we would crash.
This crash can be provoked with a command line such as
qemu-system-aarch64 -M raspi3 -kernel /dev/null -bios /dev/null -display none
It is currently only possible on the raspi3 machine, because unless
the machine sets info->firmware_loaded we won't call
arm_setup_firmware_boot(), and the only machines which set that are:
* virt (has a fw-cfg device)
* sbsa-ref (checks itself for kernel_filename && firmware_loaded)
* raspi3 (crashes)
But this is an unfortunate beartrap to leave for future machine
model implementors, so we should handle this situation in boot.c.
Check in arm_setup_firmware_boot() whether the fw-cfg device exists
before trying to load files into it, and if it doesn't exist then
exit with a hopefully helpful error message.
Because we now handle this check in a machine-agnostic way, we
can remove the check from sbsa-ref.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/503
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210726163351.32086-1-peter.maydell@linaro.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210726150953.1218690-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bit to see if a CD is valid is the last bit of the first word of the CD.
Signed-off-by: Joe Komlodi <joe.komlodi@xilinx.com>
Message-id: 1626728232-134665-2-git-send-email-joe.komlodi@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
added a dependency on the TYPE_IMX_USDHC model, but forgot to add
the Kconfig selector. Fix that to solve when built stand-alone:
$ qemu-system-arm -M imx25-pdk
qemu-system-arm: missing object type 'imx-usdhc'
Aborted (core dumped)
Fixes: bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-6-philmd@redhat.com>
In commit c4f00daa5b ("imx25-pdk: create ds1338 for qtest inside
the test") we removed the DS1338 device from the i.MX25 machine
but forgot to remove it in the machine Kconfig definitions, do
it now.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-5-philmd@redhat.com>
The TYPE_NPCM7XX_SMBUS device model exposes an SMBus, but
this isn't advertised with proper Kconfig symbol, leading
to an early build failure when building NPCM7XX machines
standalone:
The following clauses were found for AT24C
config AT24C depends on I2C
select AT24C if NPCM7XX
Fix by adding SMBUS to NPCM7XX.
Fixes: 94e7787939 ("hw/i2c: Implement NPCM7XX SMBus Module Single Mode")
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-4-philmd@redhat.com>
When we build IORT table with SMMUv3 and bypass iommu feature enabled,
we can no longer setup one map from RC to SMMUv3 covering the whole RIDs.
We need to walk the PCI bus and check whether the root bus will bypass
iommu, setup RC -> SMMUv3 -> ITS map for RC which will not bypass iommu.
When a SMMUv3 node exist, we setup the idmap from SMMUv3 to ITS
covering the whole RIDs, and only modify the map from RC to SMMUv3.
We build RC -> SMMUv3 -> ITS map for root bus with bypass_iommu
disabled, and build idmap from RC to ITS directly for the rest of
the whole RID space.
For example we run qemu with command line:
qemu/build/aarch64-softmmu/qemu-system-aarch64 \
-kernel arch/arm64/boot/Image \
-enable-kvm \
-cpu host \
-m 8G \
-smp 8,sockets=2,cores=4,threads=1 \
-machine virt,kernel_irqchip=on,gic-version=3,iommu=smmuv3,default_bus_bypass_iommu=true \
-drive file=./QEMU_EFI-pflash.raw,if=pflash,format=raw,unit=0,readonly=on \
-device pxb-pcie,bus_nr=0x10,id=pci.10,bus=pcie.0,addr=0x3.0x1 \
-device pxb-pcie,bus_nr=0x20,id=pci.20,bus=pcie.0,addr=0x3.0x2,bypass_iommu=true \
-device pcie-root-port,port=0x20,chassis=1,id=pci.1,bus=pcie.0,addr=0x2 \
-device pcie-root-port,port=0x20,chassis=11,id=pci.11,bus=pci.10,addr=0x1 \
-device pcie-root-port,port=0x20,chassis=21,id=pci.21,bus=pci.20,addr=0x1 \
-device virtio-scsi-pci,id=scsi0,bus=pci.1,addr=0x1 \
-device virtio-scsi-pci,id=scsi1,bus=pci.11,addr=0x1 \
-device virtio-scsi-pci,id=scsi2,bus=pci.21,addr=0x1 \
-initrd /mnt/davinci/wxg/kill-linux/rootfs/mfs.cpio.gz \
-nographic \
-append "rdinit=init console=ttyAMA0 earlycon=pl011,0x9000000 nokaslr" \
And we get guest configuration:
-+-[0000:20]---01.0-[21]--
+-[0000:10]---01.0-[11]--
\-[0000:00]-+-00.0 Device 1b36:0008
+-01.0 Device 1af4:1000
\-02.0-[01]--
With bypass_iommu enabled, the attached devices will bypass iommu.
/sys/class/iommu/smmu3.0x0000000009050000/
|-- device -> ../../../arm-smmu-v3.0.auto
|-- devices
| `-- 0000:10:01.0 -> ../../../../../pci0000:10/0000:10:01.0
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1625748919-52456-7-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a default_bus_bypass_iommu machine option to enable/disable
bypass_iommu for default root bus. The option is disabled by
default and can be enabled with:
$QEMU -machine virt,iommu=smmuv3,default_bus_bypass_iommu=true
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1625748919-52456-4-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
-----BEGIN PGP SIGNATURE-----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=8708
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging
Some qemu updates for IPMI and I2C
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently select CONFIG_V7M for a bunch of our m-profile devices.
The last sticking point is translate.c which cannot be compiled
without expecting v7m support. Express this dependency in Kconfig
rather than in default devices as a stepping stone to a fully
configurable translate.c.
While we are at it we also need to select ARM_COMPATIBLE_SEMIHOSTING
as that is implied for M profile machines.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210707131744.26027-4-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need this functionality due to:
/* XRAM IRQs get ORed into a single line. */
object_initialize_child(OBJECT(s), "xram-irq-orgate",
&s->lpd.xram.irq_orgate, TYPE_OR_IRQ);
Fixes: a55b441b2c ("hw/arm: versal: Add support for the XRAMs")
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707131744.26027-3-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The stellaris board doesn't emulate the handling of the OLED
chipselect line correctly. Expand the comment describing this,
including a sketch of the theoretical correct way to do it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the virt board we have two PL061 devices -- one for NonSecure which
is inputs only, and one for Secure which is outputs only. For the former,
we don't care whether its outputs are pulled low or high when the line is
configured as an input, because we don't connect them. For the latter,
we do care, because we wire the lines up to the gpio-pwr device, which
assumes that level 1 means "do the action" and 1 means "do nothing".
For consistency in case we add more outputs in future, configure both
PL061s to pull GPIO lines down to 0.
Reported-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Define TYPE_LM8323 in the public "hw/input/lm832x.h"
header and use it in hw/arm/nseries.c.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
lm832x_key_event() is specific go LM832x devices, not to the
I2C bus API. Move it out of "i2c.h" to a new header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This is just enough to make reboot and poweroff work. Works for
linux, u-boot, and the arm trusted firmware. Not tested, but should
work for plan9, and bare-metal/hobby OSes, since they seem to generally
do what linux does for reset.
The watchdog timer functionality is not yet implemented.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/64
Signed-off-by: Nolan Leake <nolan@sigbus.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210625210209.1870217-1-nolan@sigbus.net
[PMM: tweaked commit title; fixed region size to 0x200;
moved header file to include/]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of this are expected to be coming in, create a directory for them.
Also move the tmp105.h file into the include directory where it
should be.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
It's an adc, put it where it belongs.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's an ADC, put it where it belongs.
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Adds the pca954x muxes expected.
Tested: Booted quanta-q71l image to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20210608202522.2677850-4-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds comments to the board init to identify missing i2c devices.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20210608202522.2677850-2-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a comment and i2c method that describes the board layout.
Tested: firmware booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Brandon Kim <brandonkim@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210608193605.2611114-3-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210614191335.1968807-3-stefanb@linux.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The official punctuation for Arm CPU names uses a hyphen, like
"Cortex-A9". We mostly follow this, but in a few places usage
without the hyphen has crept in. Fix those so we consistently
use the same way of writing the CPU name.
This commit was created with:
git grep -z -l 'Cortex ' | xargs -0 sed -i 's/Cortex /Cortex-/'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210527095152.10968-1-peter.maydell@linaro.org
Currently we allow board models to specify the initial value of the
Secure VTOR register, using an init-svtor property on the TYPE_ARMV7M
object which is plumbed through to the CPU. Allow board models to
also specify the initial value of the Non-secure VTOR via a similar
init-nsvtor property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210520152840.24453-10-peter.maydell@linaro.org
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Per the kconfig.rst:
A device should be listed [...] ``imply`` if (depending on
the QEMU command line) the board may or may not be started
without it.
This is the case with the NVDIMM device, so use the 'imply'
weak reverse dependency to select the symbol.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210511155354.3069141-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SSE-300 has an ITCM at 0x0000_0000 and a DTCM at 0x2000_0000.
Currently we model these in the AN547 board, but this is conceptually
wrong, because they are a part of the SSE-300 itself. Move the
modelling of the TCMs out of mps2-tz.c into sse300.c.
This has no guest-visible effects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-7-peter.maydell@linaro.org
Currently we model the ITCM in the AN547's RAMInfo list. This is incorrect
because this RAM is really a part of the SSE-300. We can't just delete
it from the RAMInfo list, though, because this would make boot_ram_size()
assert because it wouldn't be able to find an entry in the list covering
guest address 0.
Allow a board to specify a boot RAM size manually if it doesn't have
any RAM itself at address 0 and is relying on the SSE for that, and
set the correct value for the AN547. The other boards can continue
to use the "look it up from the RAMInfo list" logic.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-6-peter.maydell@linaro.org
Convert armsse_realize() to use ERRP_GUARD(), following
the rules in include/qapi/error.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-5-peter.maydell@linaro.org
The SSE-300 was not correctly modelling its internal SRAMs:
* the SRAM address width default is 18
* the SRAM is mapped at 0x2100_0000, not 0x2000_0000 like
the SSE-200 and IoTKit
The default address width is no longer guest-visible since
our only SSE-300 board sets it explicitly to a non-default
value, but following the hardware's default will help for
any future boards we need to model.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-4-peter.maydell@linaro.org
The AN547 sets the SRAM_ADDR_WIDTH for the SSE-300 to 21;
since this is not the default value for the SSE-300, model this
in mps2-tz.c as a per-board value.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-3-peter.maydell@linaro.org
The SRAM at 0x2000_0000 is part of the SSE-200 itself, and we model
it that way in hw/arm/armsse.c (along with the associated MPCs). We
incorrectly also added an entry to the RAMInfo array for the AN524 in
hw/arm/mps2-tz.c, which was pointless because the CPU would never see
it. Delete it.
The bug had no guest-visible effect because devices in the SSE-200
take priority over those in the board model (armsse.c maps
s->board_memory at priority -2).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-2-peter.maydell@linaro.org
6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
failed to completely fix misalignment issues with range
invalidation. For instance invalidations patterns like "invalidate 32
4kB pages starting from 0xff395000 are not correctly handled" due
to the fact the previous fix only made sure the number of invalidated
pages were a power of 2 but did not properly handle the start
address was not aligned with the range. This can be noticed when
boothing a fedora 33 with protected virtio-blk-pci.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmCeiMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpqsIH/A49Av5Bv8huL75lf9GzCx3E1a/z2W9Fphik
OcQ1ahR+7CRDARub+vTG40MBmZBVefIWjLAj3BwBWzFGPX0DZq0zeI102VzlEVKY
OeUx8ixuiKOSLcS+QxE7ZXIBL2Pn7l+MFUi4nLMYKti7c/kola7zlB57qsmXh+VD
AOQ7Utj6NWoi6QocWJsMSCyHCh3Fk9QzcStLlr6/MkSJa1zqv8l22+8oWH07Fk2M
wZfhrm9k094on28iSejsFYL5e4ROeXUajbOdfyMIxWvAB7boC9Jxk/e0oAbuSB4y
2f71Gfk3mU6irS7PvrxcKbk6BVD2zxM2WumOchZJgxFAujDO6yg=
=fvkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: bugfixes, improvements
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 14 May 2021 15:27:13 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Fix build with 64 bits time_t
vhost-vdpa: Make vhost_vdpa_get_device_id() static
hw/virtio: enable ioeventfd configuring for mmio
hw/smbios: support for type 41 (onboard devices extended information)
checkpatch: Fix use of uninitialized value
virtio-scsi: Configure all host notifiers in a single MR transaction
virtio-scsi: Set host notifiers and callbacks separately
virtio-blk: Configure all host notifiers in a single MR transaction
virtio-blk: Fix rollback path in virtio_blk_data_plane_start()
pc-dimm: remove unnecessary get_vmstate_memory_region() method
amd_iommu: fix wrong MMIO operations
virtio-net: Constify VirtIOFeature feature_sizes[]
virtio-blk: Constify VirtIOFeature feature_sizes[]
hw/virtio: Pass virtio_feature_get_config_size() a const argument
x86: acpi: use offset instead of pointer when using build_header()
amd_iommu: Fix pte_override_page_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/virt.c
Type 41 defines the attributes of devices that are onboard. The
original intent was to imply the BIOS had some level of control over
the enablement of the associated devices.
If network devices are present in this table, by default, udev will
name the corresponding interfaces enoX, X being the instance number.
Without such information, udev will fallback to using the PCI ID and
this usually gives ens3 or ens4. This can be a bit annoying as the
name of the network card may depend on the order of options and may
change if a new PCI device is added earlier on the commande line.
Being able to provide SMBIOS type 41 entry ensure the name of the
interface won't change and helps the user guess the right name without
booting a first time.
This can be invoked with:
$QEMU -netdev user,id=internet
-device virtio-net-pci,mac=50:54:00:00:00:42,netdev=internet,id=internet-dev \
-smbios type=41,designation='Onboard LAN',instance=1,kind=ethernet,pcidev=internet-dev
The PCI segment is assumed to be 0. This should hold true for most
cases.
$ dmidecode -t 41
# dmidecode 3.3
Getting SMBIOS data from sysfs.
SMBIOS 2.8 present.
Handle 0x2900, DMI type 41, 11 bytes
Onboard Device
Reference Designation: Onboard LAN
Type: Ethernet
Status: Enabled
Type Instance: 1
Bus Address: 0000:00:09.0
$ ip -brief a
lo UNKNOWN 127.0.0.1/8 ::1/128
eno1 UP 10.0.2.14/24 fec0::5254:ff:fe00:42/64 fe80::5254:ff:fe00:42/64
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Message-Id: <20210401171138.62970-1-vincent@bernat.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit dfc388797c ("hw/arm: xlnx: Set all boards' GEM 'phy-addr'
property value to 23") configured the PHY address for xilinx-zynq-a9
to 23. When trying to boot xilinx-zynq-a9 with zynq-zc702.dtb or
zynq-zc706.dtb, this results in the following error message when
trying to use the Ethernet interface.
macb e000b000.ethernet eth0: Could not attach PHY (-19)
The devicetree files for ZC702 and ZC706 configure PHY address 7. The
documentation for the ZC702 and ZC706 evaluation boards suggest that the
PHY address is 7, not 23. Other boards use PHY address 0, 1, 3, or 7.
I was unable to find a documentation or a devicetree file suggesting
or using PHY address 23. The Ethernet interface starts working with
zynq-zc702.dtb and zynq-zc706.dtb when setting the PHY address to 7,
so let's use it.
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210504124140.1100346-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AN524 FPGA image supports two memory maps, which differ in where
the QSPI and BRAM are. In the default map, the BRAM is at
0x0000_0000, and the QSPI at 0x2800_0000. In the second map, they
are the other way around.
In hardware, the initial mapping can be selected by the user by
writing either "REMAP: BRAM" (the default) or "REMAP: QSPI" in the
board configuration file. The board config file is acted on by the
"Motherboard Configuration Controller", which is an entirely separate
microcontroller on the dev board but outside the FPGA.
The guest can also dynamically change the mapping via the SCC
CFG_REG0 register.
Implement this functionality for QEMU, using a machine property
"remap" with valid values "BRAM" and "QSPI" to allow the user to set
the initial mapping, in the same way they can on the FPGA, and
wiring up the bit from the SCC register to also switch the mapping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-4-peter.maydell@linaro.org
The i.MX25 PDK board has 2 banks for SDRAM, each can
address up to 256 MiB. So the total RAM usable for this
board is 512M. When we ask for more we get a misleading
error message:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: Invalid RAM size, should be 128 MiB
Update the error message to better match the reality:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: RAM size more than 512 MiB is not supported
Fixes: bf350daae0 ("arm/imx25_pdk: drop RAM size fixup")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20210407225608.1882855-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
-----BEGIN PGP SIGNATURE-----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=N5Us
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210503' into staging
Aspeed patches :
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
# gpg: Signature made Mon 03 May 2021 06:23:36 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210503:
aspeed: Add support for the quanta-q7l1-bmc board
hw/block: m25p80: Add support for mt25ql02g and mt25qu02g
aspeed: Add support for the rainier-bmc board
aspeed: Deprecate the swift-bmc machine
tests/qtest: Rename m25p80 test in aspeed_smc test
aspeed/smc: Add extra controls to request DMA
aspeed/smc: Add a 'features' attribute to the object class
hw/misc/aspeed_xdma: Add AST2600 support
tests/acceptance: Test ast2600 machine
tests/acceptance: Test ast2400 and ast2500 machines
tests/qtest: Add test for Aspeed HACE
aspeed: Integrate HACE
hw: Model ASPEED's Hash and Crypto Engine
hw/arm/aspeed: Do not sysbus-map mmio flash region directly, use alias
aspeed/i2c: Rename DMA address space
aspeed/i2c: Fix DMA address mask
aspeed/smc: Remove unused "sdram-base" property
aspeed/smc: Use the RAM memory region for DMAs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/sysbus.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210327082804.2259480-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Intel XScale PXA chipsets provide a PCMCIA controller,
which expose a PCMCIA bus. Express this dependency using
the Kconfig 'select' expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-2-f4bug@amsat.org>
[lv: remove "(IDE)"]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Quanta-Q71l BMC board is a board supported by OpenBMC.
Tested: Booted quanta-q71l firmware.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210416162426.3217033-1-venture@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Rainier BMC board is a board for the middle range POWER10 IBM systems.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-19-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SWIFT machine never came out of the lab and we already have enough
AST2500 based OpenPower machines.
Cc: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When we introduced support for the AST2600 SoC, the XDMA controller
was forgotten. It went unnoticed because it's not used under emulation.
But the register layout being different, the reset procedure is bogus
and this breaks kexec.
Add a AspeedXDMAClass to take into account the register differences.
Cc: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Message-Id: <20210407171637.777743-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the hash and crypto engine model to the Aspeed socs.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210409000253.1475587-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instead of passing the memory address space region, simply use the RAM
memory region instead. This simplifies RAM accesses.
This patch breaks migration compatibility.
Fixes: c4e1f0b483 ("aspeed/smc: Add support for DMAs")
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The driver can query some bits in SMMUv3 IDR5 to learn which
translation granules are supported. Arm recommends that SMMUv3
implementations support at least 4K and 64K granules. But in
the vSMMUv3, there seems to be no reason not to support 16K
translation granule. In addition, if 16K is not supported,
vSVA will failed to be enabled in the future for 16K guest
kernel. So it'd better to support it.
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-300 has a Cortex-M55 (which was the whole reason for us
modelling it), but we forgot to actually update the code to let it
have a different CPU type from the IoTKit and SSE-200. Add CPU type
as a field for ARMSSEInfo instead of hardcoding it to always use a
Cortex-M33.
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416104010.13228-1-peter.maydell@linaro.org
SSE-300 currently shares the SSE-200 Property array. This is
bad principally because the default values of the CPU0_FPU
and CPU0_DSP properties disable the FPU and DSP on the CPU.
That is correct for the SSE-200 but not the SSE-300.
Give the SSE-300 its own Property array with the correct
SSE-300 specific settings:
* SSE-300 has only one CPU, so no CPU1* properties
* SSE-300 CPU has FPU and DSP
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210415182353.8173-1-peter.maydell@linaro.org
Each board in mps2-tz.c specifies a RAMInfo[] array providing
information about each RAM in the board. The .mpc field of the
RAMInfo struct specifies which MPC, if any, the RAM is attached to.
We already assert if the array doesn't have any entry for an MPC, but
we don't diagnose the error of using the same MPC number twice (which
is quite easy to do by accident if copy-and-pasting structure
entries).
Enhance find_raminfo_for_mpc() so that it detects multiple entries
for the MPC as well as missing entries.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-3-peter.maydell@linaro.org
The AN524 has three MPCs: one for the BRAM, one for the QSPI flash,
and one for the DDR. We incorrectly set the .mpc field in the
RAMInfo struct for the SRAM block to 1, giving it the same MPC we are
using for the QSPI. The effect of this was that the QSPI didn't get
mapped into the system address space at all, via an MPC or otherwise,
and guest programs which tried to read from the QSPI would get a bus
error. Correct the SRAM RAMInfo to indicate that it does not have an
associated MPC.
Fixes: 25ff112a8c ("hw/arm/mps2-tz: Add new mps3-an524 board")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-2-peter.maydell@linaro.org
In emulation of the CFGI_STE_RANGE command, we now take StreamID as the
start of the invalidation range, regardless of whatever the Range is,
whilst the spec clearly states that
- "Invalidation is performed for an *aligned* range of 2^(Range+1)
StreamIDs."
- "The bottom Range+1 bits of the StreamID parameter are IGNORED,
aligning the range to its size."
Take CFGI_ALL (where Range == 31) as an example, if there are some random
bits in the StreamID field, we'll fail to perform the full invalidation but
get a strange range (e.g., SMMUSIDRange={.start=1, .end=0}) instead. Rework
the emulation a bit to get rid of the discrepancy with the spec.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402100449.528-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV values in SMMUv3 IORT node are not correct as they don't match
the SMMUIrq enumeration, which describes the IRQ<->PIN mapping used by
our emulated vSMMU.
Fixes: a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402084731.93-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine device plug callback currently calls
platform_bus_link_device() for any sysbus device. This is overly
broad, because platform_bus_link_device() will unconditionally grab
the IRQs and MMIOs of the device it is passed, whether it was
intended for the platform bus or not. Restrict hotpluggability of
sysbus devices to only those devices on the dynamic sysbus
allowlist.
We were mostly getting away with this because the board creates the
platform bus as the last device it creates, and so the hotplug
callback did not do anything for all the sysbus devices created by
the board itself. However if the user plugged in a device which
itself uses a sysbus device internally we would have mishandled this
and probably asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-4-peter.maydell@linaro.org
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They were introduced in commit 9bde7f0674 ("hw/arm/smmuv3: Implement
translate callback") but never actually used. Drop them.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325142702.790-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine already checks KVM_CAP_ARM_VM_IPA_SIZE to get the
upper bound of the IPA size. If that bound is lower than the highest
possible GPA for the machine, then QEMU will error out. However, the
IPA is set to 40 when the highest GPA is less than or equal to 40,
even when KVM may support an IPA limit as low as 32. This means KVM
may fail the VM creation unnecessarily. Additionally, 40 is selected
with the value 0, which means use the default, and that gets around
a check in some versions of KVM, causing a difficult to debug fail.
Always use the IPA size that corresponds to the highest possible GPA,
unless it's lower than 32, in which case use 32. Also, we must still
use 0 when KVM only supports the legacy fixed 40 bit IPA.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Message-id: 20210310135218.255205-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all sid printouts to sid=0x%x.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the whole SID range (32b) is invalidated (SMMU_CMD_CFGI_ALL),
@end overflows and we fail to handle the command properly.
Once this gets fixed, the current code really is awkward in the
sense it loops over the whole range instead of removing the
currently cached configs through a hash table lookup.
Fix both the overflow and the lookup.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210309102742.30442-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, the driver can invalidate a number of pages that is
not a power of 2. However IOTLB unmap notifications and internal
IOTLB invalidations work with masks leading to erroneous
invalidations.
In case the range is not a power of 2, split invalidations into
power of 2 invalidations.
When looking for a single page entry in the vSMMU internal IOTLB,
let's make sure that if the entry is not found using a
g_hash_table_remove() we iterate over all the entries to find a
potential range that overlaps it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the asid is not set, do not attempt to locate the key directly
as all inserted keys have a valid asid.
Use g_hash_table_foreach_remove instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-5-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
The AN505 and AN521 don't have any read-only memory, but the AN524
does; add a flag to ROMInfo to mark a region as ROM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-19-peter.maydell@linaro.org
Instead of hardcoding the MachineClass default_ram_size and
default_ram_id fields, set them on class creation by finding the
entry in the RAMInfo array which is marked as being the QEMU system
RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-18-peter.maydell@linaro.org
The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
The AN524 has a different SYSCLK frequency from the AN505 and AN521;
make the SYSCLK frequency a field in the MPS2TZMachineClass rather
than a compile-time constant so we can support the AN524.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-2-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the milkymist display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-2-peter.maydell@linaro.org
We hint the 'has_rpu' property is no longer required since commit
6908ec448b ("xlnx-zynqmp: Properly support the smp command line
option") which was released in QEMU v2.11.0.
Beside, this device is marked 'user_creatable = false', so the
only thing that could be setting the property is the board code
that creates the device.
Since the property is not user-facing, we can remove it without
going through the deprecation process.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144350.1979905-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-3-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let add 'max' cpu while work goes on adding newer CPU types than
Cortex-A72. This allows us to check SVE etc support.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Acked-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210216150122.3830863-3-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use nr_apu_cpus in favor of hard coding 2.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
NPCM7XX GPIO devices have been implemented in hw/gpio/npcm7xx-gpio.c. So
we removed them from the unimplemented devices list.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu<wuhaotsh@google.com>
Message-id: 20210129005845.416272-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gcc is not smart enough to figure out length was validated before use as
strncpy limit, resulting in this warning:
inlined from ‘virt_set_oem_table_id’ at ../../hw/arm/virt.c:2197:5:
/usr/include/aarch64-linux-gnu/bits/string_fortified.h:106:10: error:
‘__builtin_strncpy’ specified bound depends on the length of the
source argument [-Werror=stringop-overflow=]
Simplify things by using a constant limit instead.
Fixes: 97fc5d507fca ("acpi: Permit OEM ID and OEM table ID fields to be changed")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Qemu's ACPI table generation sets the fields OEM ID and OEM table ID
to "BOCHS " and "BXPCxxxx" where "xxxx" is replaced by the ACPI
table name.
Some games like Red Dead Redemption 2 seem to check the ACPI OEM ID
and OEM table ID for the strings "BOCHS" and "BXPC" and if they are
found, the game crashes(this may be an intentional detection
mechanism to prevent playing the game in a virtualized environment).
This patch allows you to override these default values.
The feature can be used in this manner:
qemu -machine oem-id=ABCDEF,oem-table-id=GHIJKLMN
The oem-id string can be up to 6 bytes in size, and the
oem-table-id string can be up to 8 bytes in size. If the string are
smaller than their respective sizes they will be padded with space.
If either of these parameters is not set, the current default values
will be used for the one missing.
Note that the the OEM Table ID field will not be extended with the
name of the table, but will use either the default name or the user
provided one.
This does not affect the -acpitable option (for user-defined ACPI
tables), which has precedence over -machine option.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210119003216.17637-3-posteuca@mutex.one>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previous work on dev-iotlb message broke vhost on either SMMU or virtio-iommu
since dev-iotlb (or PCIe ATS) is not yet supported for those archs.
An initial idea is that we can let IOMMU to export this information to vhost so
that vhost would know whether the vIOMMU would support dev-iotlb, then vhost
can conditionally register to dev-iotlb or the old iotlb way. We can work
based on some previous patch to introduce PCIIOMMUOps as Yi Liu proposed [1].
However it's not as easy as I thought since vhost_iommu_region_add() does not
have a PCIDevice context at all since it's completely a backend. It seems
non-trivial to pass over a PCI device to the backend during init. E.g. when
the IOMMU notifier registered hdev->vdev is still NULL.
To make the fix smaller and easier, this patch goes the other way to leverage
the flag_changed() hook of vIOMMUs so that SMMU and virtio-iommu can trap the
dev-iotlb registration and fail it. Then vhost could try the fallback solution
as using UNMAP invalidation for it's translations.
[1] https://lore.kernel.org/qemu-devel/1599735398-6829-4-git-send-email-yi.l.liu@intel.com/
Reported-by: Eric Auger <eric.auger@redhat.com>
Fixes: b68ba1ca57
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210204191228.187550-1-peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Most of ARM machines display their CPU when QEMU list the available
machines (-M help). Some machines do not. Fix to unify the help
output.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Versal SoC instantiates the TYPE_XLNX_ZYNQMP_RTC object in
versal_create_rtc()(). Select CONFIG_XLNX_ZYNQMP to fix:
$ make check-qtest-aarch64
...
Running test qtest-aarch64/qom-test
qemu-system-aarch64: missing object type 'xlnx-zynmp.rtc'
Broken pipe
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Versal SoC instantiates the TYPE_XLNX_ZDMA object in
versal_create_admas(). Introduce the XLNX_ZDMA configuration
and select it to fix:
$ qemu-system-aarch64 -M xlnx-versal-virt ...
qemu-system-aarch64: missing object type 'xlnx.zdma'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exynos4210 SoC uses an OR gate on the PL330 IRQ lines.
Fixes: dab15fbe2a ("hw/arm/exynos4210: Fix DMA initialization")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210131184449.382425-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STM32F405 SoC uses an OR gate on its ADC IRQs.
Fixes: 529fc5fd3e ("hw/arm: Add the STM32F4xx SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210131184449.382425-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When handling guest range-based IOTLB invalidation, we should decode the TG
field into the corresponding translation granule size so that we can pass
the correct invalidation range to backend. Set @granule to (tg * 2 + 10) to
properly emulate the architecture.
Fixes: d52915616c ("hw/arm/smmuv3: Get prepared for range invalidation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210130043220.1345-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the watchdog device uses its Clock input rather than being
passed the value of system_clock_scale at creation time, we can
remove the hack where we reset the STELLARIS_SYS at board creation
time to force it to set system_clock_scale. Instead it will be reset
at the usual point in startup and will inform the watchdog of the
clock frequency at that point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-26-peter.maydell@linaro.org
Message-id: 20210121190622.22000-26-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now no users are setting the frq properties on the CMSDK timer,
dualtimer, watchdog or ARMSSE SoC devices, we can remove the
properties and the struct fields that back them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-25-peter.maydell@linaro.org
Message-id: 20210121190622.22000-25-peter.maydell@linaro.org
Remove all the code that sets frequency properties on the CMSDK
timer, dualtimer and watchdog devices and on the ARMSSE SoC device:
these properties are unused now that the devices rely on their Clock
inputs instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-24-peter.maydell@linaro.org
Message-id: 20210121190622.22000-24-peter.maydell@linaro.org
Use the MAINCLK Clock input to set the system_clock_scale variable
rather than using the mainclk_frq property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210128114145.20536-23-peter.maydell@linaro.org
Message-id: 20210121190622.22000-23-peter.maydell@linaro.org
Create and connect the Clock input for the watchdog device on the
Stellaris boards. Because the Stellaris boards model the ability to
change the clock rate by programming PLL registers, we have to create
an output Clock on the ssys_state device and wire it up to the
watchdog.
Note that the old comment on ssys_calculate_system_clock() got the
units wrong -- system_clock_scale is in nanoseconds, not
milliseconds. Improve the commentary to clarify how we are
calculating the period.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-18-peter.maydell@linaro.org
Message-id: 20210121190622.22000-18-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Convert the SSYS code in the Stellaris boards (which encapsulates the
system registers) to a proper QOM device. This will provide us with
somewhere to put the output Clock whose frequency depends on the
setting of the PLL configuration registers.
This is a migration compatibility break for lm3s811evb, lm3s6965evb.
We use 3-phase reset here because the Clock will need to propagate
its value in the hold phase.
For the moment we reset the device during the board creation so that
the system_clock_scale global gets set; this will be removed in a
subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-17-peter.maydell@linaro.org
Message-id: 20210121190622.22000-17-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Create a fixed-frequency Clock object to be the SYSCLK, and wire it
up to the devices that require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-14-peter.maydell@linaro.org
Message-id: 20210121190622.22000-14-peter.maydell@linaro.org
The old-style convenience function cmsdk_apb_timer_create() for
creating CMSDK_APB_TIMER objects is used in only two places in
mps2.c. Most of the rest of the code in that file uses the new
"initialize in place" coding style.
We want to connect up a Clock object which should be done between the
object creation and realization; rather than adding a Clock* argument
to the convenience function, convert the timer creation code in
mps2.c to the same style as is used already for the watchdog,
dualtimer and other devices, and delete the now-unused convenience
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-13-peter.maydell@linaro.org
Message-id: 20210121190622.22000-13-peter.maydell@linaro.org
Create two input clocks on the ARMSSE devices, one for the normal
MAINCLK, and one for the 32KHz S32KCLK, and wire these up to the
appropriate devices. The old property-based clock frequency setting
will remain in place until conversion is complete.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-12-peter.maydell@linaro.org
Message-id: 20210121190622.22000-12-peter.maydell@linaro.org
While we transition the ARMSSE code from integer properties
specifying clock frequencies to Clock objects, we want to have the
device provide both at once. We want the final name of the main
input Clock to be "MAINCLK", following the hardware name.
Unfortunately creating an input Clock with a name X creates an
under-the-hood QOM property X; for "MAINCLK" this clashes with the
existing UINT32 property of that name.
Rename the UINT32 property to MAINCLK_FRQ so it can coexist with the
MAINCLK Clock; once the transition is complete MAINCLK_FRQ will be
deleted.
Commit created with:
perl -p -i -e 's/MAINCLK/MAINCLK_FRQ/g' hw/arm/{armsse,mps2-tz,musca}.c include/hw/arm/armsse.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-11-peter.maydell@linaro.org
Message-id: 20210121190622.22000-11-peter.maydell@linaro.org
Add secure pl061 for reset/power down machine from
the secure world (Arm Trusted Firmware). Connect it
with gpio-pwr driver.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
[PMM: Added mention of the new device to the documentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No functional change. Just refactor code to better
support secure and normal world gpios.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The properties to attach a CANBUS object to the xlnx-zcu102 machine have
a period in them. We want to use periods in properties for compound QAPI types,
and besides the "xlnx-zcu102." prefix is both unnecessary and different
from any other machine property name. Remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210118162537.779542-1-pbonzini@redhat.com
Reviewed-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A device shouldn't access its parent object which is QOM internal.
Instead it should use type cast for this purporse. This patch fixes this
issue for all NPCM7XX Devices.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210108190945.949196-7-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two
identical PWM modules. Each module contains 4 PWM entries. Each PWM has
two outputs: frequency and duty_cycle. Both are computed using inputs
from software side.
This module does not model detail pulse signals since it is expensive.
It also does not model interrupts and watchdogs that are dependant on
the detail models. The interfaces for these are left in the module so
that anyone in need for these functionalities can implement on their
own.
The user can read the duty cycle and frequency using qom-get command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-5-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ADC is part of NPCM7XX Module. Its behavior is controled by the
ADC_CON register. It converts one of the eight analog inputs into a
digital input and stores it in the ADC_DATA register when enabled.
Users can alter input value by using qom-set QMP command.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-4-wuhaotsh@google.com
[PMM: Added missing hw/adc/trace.h file]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch makes NPCM7XX Timer to use a the timer clock generated by the
CLK module instead of the magic number TIMER_REF_HZ.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present, when booting U-Boot on QEMU sabrelite, we see:
Net: Board Net Initialization Failed
No ethernet found.
U-Boot scans PHY at address 4/5/6/7 (see board_eth_init() in the
U-Boot source: board/boundary/nitrogen6x/nitrogen6x.c). On the real
board, the Ethernet PHY is at address 6. Adjust this by updating the
"fec-phy-num" property of the fsl_imx6 SoC object.
With this change, U-Boot sees the PHY but complains MAC address:
Net: using phy at 6
FEC [PRIME]
Error: FEC address not set.
This is due to U-Boot tries to read the MAC address from the fuse,
which QEMU does not have any valid content filled in. However this
does not prevent the Ethernet from working in QEMU. We just need to
set up the MAC address later in the U-Boot command shell, by:
=> setenv ethaddr 00:11:22:33:44:55
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210106063504.10841-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running device-introspect-test, a memory leak occurred in the
mv88w8618_pit_init function, so use ptimer_free() in the finalize function to
avoid it.
ASAN shows memory leak stack:
Indirect leak of 192 byte(s) in 4 object(s) allocated from:
#0 0xffffab97e1f0 in __interceptor_calloc (/lib64/libasan.so.5+0xee1f0)
#1 0xffffab256800 in g_malloc0 (/lib64/libglib-2.0.so.0+0x56800)
#2 0xaaabf555db84 in timer_new_full /qemu/include/qemu/timer.h:523
#3 0xaaabf555db84 in timer_new /qemu/include/qemu/timer.h:544
#4 0xaaabf555db84 in timer_new_ns /qemu/include/qemu/timer.h:562
#5 0xaaabf555db84 in ptimer_init /qemu/hw/core/ptimer.c:433
#6 0xaaabf5bb2290 in mv88w8618_timer_init /qemu/hw/arm/musicpal.c:862
#7 0xaaabf5bb2290 in mv88w8618_pit_init /qemu/hw/arm/musicpal.c:954
#8 0xaaabf6339f6c in object_initialize_with_type /qemu/qom/object.c:515
#9 0xaaabf633a1e0 in object_new_with_type /qemu/qom/object.c:729
#10 0xaaabf6375e40 in qmp_device_list_properties /qemu/qom/qom-qmp-cmds.c:153
#11 0xaaabf5a95540 in qdev_device_help /qemu/softmmu/qdev-monitor.c:283
#12 0xaaabf5a96940 in qmp_device_add /qemu/softmmu/qdev-monitor.c:801
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support for running KVM on 32-bit Arm hosts was removed in commit
82bf7ae84c. You can still run a 32-bit guest on a 64-bit Arm
host CPU, but because Arm KVM requires the host and guest CPU types
to match, it is not possible to run a guest that requires a Cortex-A9
or Cortex-A15 CPU there. That means that the code in the
highbank/midway board models to support KVM is no longer used, and we
can delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201215144215.28482-1-peter.maydell@linaro.org
virt machine's 'smp_cpus' and machine->smp.cpus must always have the
same value. And, anywhere we have virt machine state we have machine
state. So let's remove the redundancy. Also, to make it easier to see
that machine->smp is the true source for "smp_cpus" and "max_cpus",
avoid passing them in function parameters, preferring instead to get
them from the state.
No functional change intended.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Ying Fang <fangying1@huawei.com>
Message-id: 20201215174815.51520-1-drjones@redhat.com
[PMM: minor formatting tweak to smp_cpus variable declaration]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already have a generic PCI_DEVFN() macro in "hw/pci/pci.h"
to pack the PCI slot/function identifiers, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20201012124506.3406909-6-philmd@redhat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201231224911.1467352-4-f4bug@amsat.org>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Machine options can be retrieved as properties of the machine object.
Encourage that by removing the "easy" accessor to machine options.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
-----BEGIN PGP SIGNATURE-----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=lHZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201215' into staging
target-arm queue:
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
# gpg: Signature made Tue 15 Dec 2020 13:59:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201215:
hw/block/m25p80: Fix Numonyx fast read dummy cycle count
hw/block/m25p80: Check SPI mode before running some Numonyx commands
hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
hw/block/m25p80: Make Numonyx config field names more accurate
hw/misc/zynq_slcr: Avoid #DIV/0! error
arm: xlnx-versal: Connect usb to virt-versal
usb: xlnx-usb-subsystem: Add xilinx usb subsystem
usb: Add DWC3 model
usb: Add versal-usb2-ctrl-regs module
elf_ops.h: Be more verbose with ROM blob names
elf_ops.h: Don't truncate name of the ROM blobs we create
hw/core/loader.c: Improve reporting of ROM overlap errors
hw/core/loader.c: Track last-seen ROM in rom_check_and_register_reset()
target/nios2: Use deposit32() to update ipending register
target/nios2: Move nios2_check_interrupts() into target/nios2
target/nios2: Move IIC code into CPU object proper
target/openrisc: Move pic_cpu code into CPU object proper
hw/openrisc/openrisc_sim: Abstract out "get IRQ x of CPU y"
hw/openrisc/openrisc_sim: Use IRQ splitter when connecting IRQ to multiple CPUs
gdbstub: Correct misparsing of vCont C/S requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Note: "its" is currently registered conditionally, but this makes
the feature be registered unconditionally. The only side effect
is that it will be now possible to set its=on on virt-2.7 and
older.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-7-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Connect VersalUsb2 subsystem to xlnx-versal SOC, its placed
in iou of lpd domain and configure it as dual port host controller.
Add the respective guest dts nodes for "xlnx-versal-virt" machine.
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1607023357-5096-5-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201111183823.283752-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ads7846 is a touch-screen controller that is an input device rather
than a display device, so move it to the hw/input folder.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201115123503.1110665-1-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Pull defaults to digic4_board_init so that a MachineState is available.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get the firmware name from the MachineState object.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-4-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
-----BEGIN PGP SIGNATURE-----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=abAb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20201210' into staging
Aspeed patches :
* New device model for EMC1413/EMC1414 temperature sensors (I2C)
* New g220a-bmc Aspeed machine
* couple of Aspeed cleanups
# gpg: Signature made Thu 10 Dec 2020 11:58:10 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20201210:
aspeed: g220a-bmc: Add an FRU
aspeed/smc: Add support for address lane disablement
ast2600: SRAM is 89KB
aspeed: Add support for the g220a-bmc board
hw/misc: add an EMC141{3,4} device model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct a typo in the name we give the NVIC object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-28-peter.maydell@linaro.org
For M-profile CPUs, the range from 0xe0000000 to 0xe00fffff is the
Private Peripheral Bus range, which includes all of the memory mapped
devices and registers that are part of the CPU itself, including the
NVIC, systick timer, and debug and trace components like the Data
Watchpoint and Trace unit (DWT). Within this large region, the range
0xe000e000 to 0xe000efff is the System Control Space (NVIC, system
registers, systick) and 0xe002e000 to 0exe002efff is its Non-secure
alias.
The architecture is clear that within the SCS unimplemented registers
should be RES0 for privileged accesses and generate BusFault for
unprivileged accesses, and we currently implement this.
It is less clear about how to handle accesses to unimplemented
regions of the wider PPB. Unprivileged accesses should definitely
cause BusFaults (R_DQQS), but the behaviour of privileged accesses is
not given as a general rule. However, the register definitions of
individual registers for components like the DWT all state that they
are RES0 if the relevant component is not implemented, so the
simplest way to provide that is to provide RAZ/WI for the whole range
for privileged accesses. (The v7M Arm ARM does say that reserved
registers should be UNK/SBZP.)
Expand the container MemoryRegion that the NVIC exposes so that
it covers the whole PPB space. This means:
* moving the address that the ARMV7M device maps it to down by
0xe000 bytes
* moving the off and the offsets within the container of all the
subregions forward by 0xe000 bytes
* adding a new default MemoryRegion that covers the whole container
at a lower priority than anything else and which provides the
RAZWI/BusFault behaviour
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-2-peter.maydell@linaro.org
Trusted Firmware now supports A72 on sbsa-ref by default [1] so enable
it for QEMU as well. A53 was already enabled there.
1. https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7117
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201120141705.246690-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CAN0 and CAN1 on the ZynqMP.
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Vikram Garhwal <fnu.vikram@xilinx.com>
Message-id: 1605728926-352690-3-git-send-email-fnu.vikram@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Accroding to the SMMUv3 spec, the SPAN field of Level1 Stream Table
Descriptor is 5 bits([4:0]).
Fixes: 9bde7f0674f(hw/arm/smmuv3: Implement translate callback)
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Message-id: 20201124023711.1184-1-jiangkunkun@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an eeprom device and fill it with fru
information
$ ipmitool fru print 0
Product Manufacturer : Bytedance
Product Name : G220A
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201210103607.556-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On the AST2600A1, the SRAM size was increased to 89KB.
Fixes: 7582591ae7 ("aspeed: Support AST2600A1 silicon revision")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201112012113.835858-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
G220A is a 2 socket x86 motherboard supported by OpenBMC.
Strapping configuration was obtained from hardware.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20201122105134.671-2-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Largely inspired by the TMP421 temperature sensor, here is a model for
the EMC1413/EMC1414 temperature sensors.
Specs can be found here :
http://ww1.microchip.com/downloads/en/DeviceDoc/20005274A.pdf
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201122105134.671-1-wangzhiqiang.bj@bytedance.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If table size is changed between virt_acpi_build and
virt_acpi_build_update, the table size would not be updated to
UEFI, therefore, just align the size to 128kb, which is enough
and same with x86. It would warn if 64k is not enough and the
align size should be updated.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-7-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resources of pxbs are obtained by crs_build and the resources
used by pxbs would be moved from the resources defined for host-bridge.
The resources for pxb are composed of following two parts:
1. The bar space of the pci-bridge/pcie-root-port behined it
2. The config space of devices behind it.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add bus property to virt machine for primary PCI root bus and use it to add
extra pci roots behind it.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This way we can tell between regular IOMMUTLBEntry (entry of IOMMU
hardware) and notifications.
In the notifications, we set explicitly if it is a MAPs or an UNMAP,
instead of trusting in entry permissions to differentiate them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Previous name didn't reflect the iommu operation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We should use printf format specifier "%u" instead of "%i" for
argument of type "unsigned int".
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Message-id: 5F9FD78B.8000300@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The removal of the selection of A15MPCORE from ARM_VIRT also
removed what A15MPCORE selects, ARM_GIC. We still need ARM_GIC.
Fixes: bec3c97e0c ("hw/arm/virt: Remove dependency on Cortex-A15 MPCore peripherals")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201111143440.112763-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nseries machines have a codepath that allows them to load a
secondary bootloader. This code wasn't checking that the
load_image_targphys() succeeded. Check the return value and report
the error to the user.
While we're in the vicinity, fix the comment style of the
comment documenting what this image load is doing.
Fixes: Coverity CID 1192904
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201103114918.11807-1-peter.maydell@linaro.org
We don't need to fill the full pic[] array if we only use
few of the interrupt lines. Directly call qdev_get_gpio_in()
when necessary.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MusicPal board code connects both of the IRQ outputs of the UART
to the same INTC qemu_irq. Connecting two qemu_irqs outputs directly
to the same input is not valid as it produces subtly wrong behaviour
(for instance if both the IRQ lines are high, and then one goes
low, the INTC input will see this as a high-to-low transition
even though the second IRQ line should still be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
omap2420_mpu_init() introduced in commit 827df9f3c5 ("Add basic
OMAP2 chip support") takes care of creating the 3 UARTs.
Then commit 58a26b477e ("Emulate a serial bluetooth HCI with H4+
extensions and attach to n8x0's UART") added n8x0_uart_setup()
which create the UART and connects it to an IRQ output,
overwritting the existing peripheral and its IRQ connection.
This is incorrect.
Fortunately we don't need to fix this, because commit 6da68df7f9
("hw/arm/nseries: Replace the bluetooth chardev with a "null"
chardev") removed the use of this peripheral. We can simply
remove the code.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The system configuration controller (SYSCFG) doesn't have
any output IRQ (and the INTC input #71 belongs to the UART6).
Remove the invalid code.
Fixes: db635521a0 ("stm32f205: Add the stm32f205 SoC")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can use one MPC per SRAM bank, but we currently only wire the
IRQ from the first expansion MPC to the IRQ splitter. Fix that.
Fixes: bb75e16d5e ("hw/arm/iotkit: Wire up MPC interrupt lines")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using a Cortex-A15, the Virt machine does not use any
MPCore peripherals. Remove the dependency.
Fixes: 7951c7b7c0 ("hw/arm: Express dependencies of the virt machine with Kconfig")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201107114852.271922-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 32bd322a01 ("hw/timer/armv7m_systick: Rewrite to use ptimers")
changed armv7m_systick to build on ptimers. Make sure we have ptimers
in the build when building armv7m_systick.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201104103343.30392-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting a CPU with EL3 using the -kernel flag, set up CPTR_EL3 so
that SVE will not trap to EL3.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030151541.11976-1-remi@remlab.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BIT_ULL() macro to ensure we use 64-bit arithmetic.
This fixes the following Coverity issue (OVERFLOW_BEFORE_WIDEN):
CID 1432363 (#1 of 1): Unintentional integer overflow:
overflow_before_widen:
Potentially overflowing expression 1 << scale with type int
(32 bits, signed) is evaluated using 32-bit arithmetic, and
then used in a context that expects an expression of type
hwaddr (64 bits, unsigned).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201030144617.1535064-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
-----BEGIN PGP SIGNATURE-----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=igPS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20201028' into staging
ppc patch queue 2020-10-28
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
# gpg: Signature made Tue 27 Oct 2020 14:13:21 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20201028:
ppc/: fix some comment spelling errors
spapr: Improve spapr_reallocate_hpt() error reporting
target/ppc: Fix kvmppc_load_htab_chunk() error reporting
spapr: Use error_append_hint() in spapr_reallocate_hpt()
spapr: Simplify error handling in spapr_memory_plug()
spapr: Pass &error_abort when getting some PC DIMM properties
spapr: Use appropriate getter for PC_DIMM_SLOT_PROP
spapr: Use appropriate getter for PC_DIMM_ADDR_PROP
pc-dimm: Drop @errp argument of pc_dimm_plug()
spapr: Simplify spapr_cpu_core_realize() and spapr_cpu_core_unrealize()
spapr: Make spapr_cpu_core_unrealize() idempotent
spapr: Drop spapr_delete_vcpu() unused argument
spapr: Unrealize vCPUs with qdev_unrealize()
spapr: Fix leak of CPU machine specific data
spapr: Move spapr_create_nvdimm_dr_connectors() to core machine code
hw/net: move allocation to the heap due to very large stack frame
ppc/spapr: re-assert IRQs during event-scan if there are pending
spapr: Clarify why DR connectors aren't user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
