VRCPSS, VRSQRTSS and VCVTSx2Sx have a 32-bit or 64-bit memory operand,
which is represented in the decoding tables by X86_VEX_REPScalar. Add it
to the tables, and make validate_vex() handle the case of an instruction
that is in exception type 4 without the REP prefix and exception type 5
with it; this is the cas of VRCP and VRSQRT.
Reported-by: yongwoo <https://gitlab.com/yongwoo36>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1377
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When in 64-bit mode, IDT entiries are 16 bytes, so `intno * 16` is used
for base/limit/offset calculations. However, even in 64-bit mode, the
exception error code still uses bits [3,16) for the invlaid interrupt
index.
This means the error code should still be `intno * 8 + 2` even in 64-bit
mode.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1382
Signed-off-by: Joe Richey <joerichey@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In get_physical_address, the canonical address check failed to
set TranslateFault.stage2, which resulted in an uninitialized
read from the struct when reporting the fault in x86_cpu_tlb_fill.
Adjust all error paths to use structure assignment so that the
entire struct is always initialized.
Reported-by: Daniel Hoffman <dhoff749@gmail.com>
Fixes: 9bbcf37219 ("target/i386: Reorg GET_HPHYS")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221201074522.178498-1-richard.henderson@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1324
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMX state is saved/restored by FSAVE/FRSTOR so the instructions are
not illegal opcodes even if CR4.OSFXSR=0. Make sure that validate_vex
takes into account the prefix and only checks HF_OSFXSR_MASK in the
presence of an SSE instruction.
Fixes: 20581aadec ("target/i386: validate VEX prefixes via the instructions' exception classes", 2022-10-18)
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1350
Reported-by: Helge Konetzka (@hejko on gitlab.com)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When translating code that is using LAHF and SAHF in combination with the
REX prefix, the instructions should not use any other register than AH;
however, QEMU selects SPL (SP being register 4, just like AH) if the
REX prefix is present. To fix this, use deposit directly without
going through gen_op_mov_v_reg and gen_op_mov_reg_v.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/130
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Unlike the memory case, where "the destination operand receives a write
cycle without regard to the result of the comparison", rm must not be
touched altogether if the write fails, including not zero-extending
it on 64-bit processors. This is not how the movcond currently works,
because it is always followed by a gen_op_mov_reg_v to rm.
To fix it, introduce a new function that is similar to gen_op_mov_reg_v
but writes to a TCG temporary.
Considering that gen_extu(ot, oldv) is not needed in the memory case
either, the two cases for register and memory destinations are different
enough that one might as well fuse the two "if (mod == 3)" into one.
So do that too.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/508
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[rth: Add a test case ]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
If CR0.PG is unset, pg_mode will be zero, but it will also be zero
for non-PAE/non-PSE page tables with CR0.WP=0. Restore the
correct test for paging enabled.
Fixes: 98281984a3 ("target/i386: Add MMU_PHYS_IDX and MMU_NESTED_IDX")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1269
Reported-by: Andreas Gustafsson <gson@gson.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221102091232.1092552-1-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The helpers for reset_rf, cli, sti, clac, stac are
completely trivial; implement them inline.
Drop some nearby #if 0 code.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The value passed is always true, and if the target's
synchronize_from_tb hook is non-trivial, not exiting
may be erroneous.
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The only issue with FMA instructions is that there are _a lot_ of them (30
opcodes, each of which comes in up to 4 versions depending on VEX.W and
VEX.L; a total of 96 possibilities). However, they can be implement with
only 6 helpers, two for scalar operations and four for packed operations.
(Scalar versions do not do any merging; they only affect the bottom 32
or 64 bits of the output operand. Therefore, there is no separate XMM
and YMM of the scalar helpers).
First, we can reduce the number of helpers to one third by passing four
operands (one output and three inputs); the reordering of which operands
go to the multiply and which go to the add is done in emit.c.
Second, the different instructions also dispatch to the same softfloat
function, so the flags for float32_muladd and float64_muladd are passed
in the helper as int arguments, with a little extra complication to
handle FMADDSUB and FMSUBADD.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
F16C only consists of two instructions, which are a bit peculiar
nevertheless.
First, they access only the low half of an YMM or XMM register for the
packed-half operand; the exact size still depends on the VEX.L flag.
This is similar to the existing avx_movx flag, but not exactly because
avx_movx is hardcoded to affect operand 2. To this end I added a "ph"
format name; it's possible to reuse this approach for the VPMOVSX and
VPMOVZX instructions, though that would also require adding two more
formats for the low-quarter and low-eighth of an operand.
Second, VCVTPS2PH is somewhat weird because it *stores* the result of
the instruction into memory rather than loading it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VROUND, FSTCW and STMXCSR all have to perform the same conversion from
x86 rounding modes to softfloat constants. Since the ISA is consistent
on the meaning of the two-bit rounding modes, extract the common code
into a wrapper for set_float_rounding_mode.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the destination is a memory register, op->n is -1. Going through
tcg_gen_gvec_dup_imm path is both useless (the value has been stored
by the gen_* function already) and wrong because of the out-of-bounds
access.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With all SSE (and AVX!) instructions now implemented in disas_insn_new,
it's possible to remove gen_sse, as well as the helpers for instructions
that now use gvec.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds another kind of weirdness when you thought you had seen it all:
an opcode byte that comes _after_ the address, not before. It's not
worth adding a new X86_SPECIAL_* constant for it, but it's actually
not unlike VCMP; so, forgive me for exploiting the similarity and just
deciding to dispatch to the right gen_helper_* call in a single code
generation function.
In fact, the old decoder had a bug where s->rip_offset should have
been set to 1 for 3DNow! instructions, and it's fixed now.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are exactly the same as the non-VEX version, but one has to be careful
that only VEX.L=0 is allowed.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here the code is a bit uglier due to the truncation and extension
of registers to and from 32-bit. There is also a mistake in the
manual with respect to the size of the memory operand of CVTPS2PI
and CVTTPS2PI, reported by Ricky Zhou.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are mostly moves, and yet are a total pain. The main issue
is that:
1) some instructions are selected by mod==11 (register operand)
vs. mod=00/01/10 (memory operand)
2) stores to memory are two-operand operations, while the 3-register
and load-from-memory versions operate on the entire contents of the
destination; this makes it easier to separate the gen_* function for
the store case
3) it's inefficient to load into xmm_T0 only to move the value out
again, so the gen_* function for the load case is separated too
The manual also has various mistakes in the operands here, for example
the store case of MOVHPS operates on a 128-bit source (albeit discarding
the bottom 64 bits) and therefore should be Mq,Vdq rather than Mq,Vq.
Likewise for the destination and source of MOVHLPS.
VUNPCK?PS and VUNPCK?PD are the same as VUNPCK?DQ and VUNPCK?QDQ,
but encoded as prefixes rather than separate operands. The helpers
can be reused however.
For MOVSLDUP, MOVSHDUP and MOVDDUP I chose to reimplement them as
helpers. I named the helper for MOVDDUP "movdldup" in preparation
for possible future introduction of MOVDHDUP and to clarify the
similarity with MOVSLDUP.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nothing special going on here, for once.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several special cases here:
1) extending moves have different widths for the helpers vs. for the
memory loads, and the width for memory loads depends on VEX.L too.
This is represented by X86_SPECIAL_AVXExtMov.
2) some instructions, such as variable-width shifts, select the vector element
size via REX.W.
3) VSIB instructions (VGATHERxPy, VPGATHERxy) are also part of this group,
and they have (among other things) two output operands.
3) the macros for 4-operand blends (which are under 0x0f 0x3a) have to be
extended to support 2-operand blends. The 2-operand variant actually
came a few years earlier, but it is clearer to implement them in the
opposite order.
X86_TYPE_WM, introduced earlier for unaligned loads, is reused for helpers
that accept a Reg* but have a M argument.
These three-byte opcodes also include AVX new instructions, for which
the helpers were originally implemented by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As pmovmskb is used by strlen et al, this is the third
highest overhead sse operation at %0.8.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[Reorganize to generate code for any vector size. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The more complicated operations here are insertions and extractions.
Otherwise, there are just more entries than usual because the PS/PD/SS/SD
variations are encoded in the opcode rater than in the prefixes.
These three-byte opcodes also include AVX new instructions, whose
implementation in the helpers was originally done by Paul Brook
<paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The more complicated ones here are d6-d7, e6-e7, f7. The others
are trivial.
For LDDQU, using gen_load_sse directly might corrupt the register if
the second part of the load fails. Therefore, add a custom X86_TYPE_WM
value; like X86_TYPE_W it does call gen_load(), but it also rejects a
value of 11 in the ModRM field like X86_TYPE_M.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This includes shifts by immediate, which use bits 3-5 of the ModRM byte
as an opcode extension. With the exception of 128-bit shifts, they are
implemented using gvec.
This also covers VZEROALL and VZEROUPPER, which use the same opcode
as EMMS. If we were wanting to optimize out gen_clear_ymmh then this
would be one of the starting points. The implementation of the VZEROALL
and VZEROUPPER helpers is by Paul Brook.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are a mixed batch, including the first two horizontal
(66 and F2 only) operations, more moves, and SSE4a extract/insert.
Because SSE4a is pretty rare, I chose to leave the helper as they are,
but it is possible to unify them by loading index and length from the
source XMM register and generating deposit or extract TCG ops.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are mostly floating-point SSE operations. The odd ones out
are MOVMSK and CVTxx2yy, the others are straightforward.
Unary operations are a bit special in AVX because they have 2 operands
for PD/PS operands (VEX.vvvv must be 1111b), and 3 operands for SD/SS.
They are handled using X86_OP_GROUP3 for compactness.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are more simple integer instructions present in both MMX and SSE/AVX,
with no holes that were later occupied by newer instructions.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are both MMX and SSE/AVX instructions, except for vmovdqu. In both
cases the inputs and output is in s->ptr{0,1,2}, so the only difference
between MMX, SSE, and AVX is which helper to call.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new implementation of SSE will cover AVX from the get go, because
all the work for the helper functions is already done. We just need to
build them.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Compared to Paul's implementation, the new decoder will use a different approach
to implement AVX's merging of dst with src1 on scalar operations. Adjust the
old SSE decoder to be compatible with new-style helpers.
The affected instructions are CVTSx2Sx, ROUNDSx, RSQRTSx, SQRTSx, RCPSx.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add to the helpers all the operands that are needed to implement AVX.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Message-Id: <20220424220204.2493824-26-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because these are the only VEX instructions that QEMU supports, the
new decoder is entered on the first byte of a valid VEX prefix, and VEX
decoding only needs to be done in decode-new.c.inc.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many SSE and AVX instructions are only valid with specific prefixes
(none, 66, F3, F2). Introduce a direct way to encode this in the
decoding table to avoid using decode groups too much.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new hflag bit to determine whether AVX instructions are allowed
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-4-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
TCG will shortly implement VAES instructions, so add the relevant feature
word to the DisasContext.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add generic code generation that takes care of preparing operands
around calls to decode.e.gen in a table-driven manner, so that ALU
operations need not take care of that.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new decoder is based on three principles:
- use mostly table-driven decoding, using tables derived as much as possible
from the Intel manual. Centralizing the decode the operands makes it
more homogeneous, for example all immediates are signed. All modrm
handling is in one function, and can be shared between SSE and ALU
instructions (including XMM<->GPR instructions). The SSE/AVX decoder
will also not have duplicated code between the 0F, 0F38 and 0F3A tables.
- keep the code as "non-branchy" as possible. Generally, the code for
the new decoder is more verbose, but the control flow is simpler.
Conditionals are not nested and have small bodies. All instruction
groups are resolved even before operands are decoded, and code
generation is separated as much as possible within small functions
that only handle one instruction each.
- keep address generation and (for ALU operands) memory loads and writeback
as much in common code as possible. All ALU operations for example
are implemented as T0=f(T0,T1). For non-ALU instructions,
read-modify-write memory operations are rare, but registers do not
have TCGv equivalents: therefore, the common logic sets up pointer
temporaries with the operands, while load and writeback are handled
by gvec or by helpers.
These principles make future code review and extensibility simpler, at
the cost of having a relatively large amount of code in the form of this
patch. Even EVEX should not be _too_ hard to implement (it's just a crazy
large amount of possibilities).
This patch introduces the main decoder flow, and integrates the old
decoder with the new one. The old decoder takes care of parsing
prefixes and then optionally drops to the new one. The changes to the
old decoder are minimal and allow it to be replaced incrementally with
the new one.
There is a debugging mechanism through a "LIMIT" environment variable.
In user-mode emulation, the variable is the number of instructions
decoded by the new decoder before permanently switching to the old one.
In system emulation, the variable is the highest opcode that is decoded
by the new decoder (this is less friendly, but it's the best that can
be done without requiring deterministic execution).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
REX.W can be used even in 32-bit mode by AVX instructions, where it is retroactively
renamed to VEX.W. Make the field available even in 32-bit mode but keep the REX_W()
macro as it was; this way, that the handling of dflag does not use it by mistake and
the AVX code more clearly points at the special VEX behavior of the bit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ldq takes a pointer to the first byte to load the 64-bit word in;
ldo takes a pointer to the first byte of the ZMMReg. Make them
consistent, which will be useful in the new SSE decoder's
load/writeback routines.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than recurse directly on mmu_translate, go through the
same softmmu lookup that we did for the page table walk.
This centralizes all knowledge of MMU_NESTED_IDX, with respect
to setup of TranslationParams, to get_physical_address.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-10-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use probe_access_full in order to resolve to a host address,
which then lets us use a host cmpxchg to update the pte.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/279
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-9-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We don't need one variable set per translation level,
which requires copying into pte/pte_addr for huge pages.
Standardize on pte/pte_addr for all levels.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-8-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use MMU_NESTED_IDX for each memory access, rather than
just a single translation to physical. Adjust svm_save_seg
and svm_load_seg to pass in mmu_idx.
This removes the last use of get_hphys so remove it.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-7-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These new mmu indexes will be helpful for improving
paging and code throughout the target.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-6-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace with PTE_HPHYS for the page table walk, and a direct call
to mmu_translate for the final stage2 translation. Hoist the check
for HF2_NPT_MASK out to get_physical_address, which avoids the
recursive call when stage2 is disabled.
We can now return all the way out to x86_cpu_tlb_fill before raising
an exception, which means probe works.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-5-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create TranslateParams for inputs, TranslateResults for successful
outputs, and TranslateFault for error outputs; return true on success.
Move stage1 error paths from handle_mmu_fault to x86_cpu_tlb_fill;
reorg the rest of handle_mmu_fault into get_physical_address.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-4-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a boolean to control the call to get_hphys instead
of passing a null function pointer.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-3-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace int is_write1 and magic numbers with the proper
MMUAccessType access_type and enumerators.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221002172956.265735-2-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Restore pc_save while undoing any state change that may have
happened while decoding the instruction. Leave a TODO about
removing all of that when the table-based decoder is complete.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221016222303.288551-1-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for saving/restoring extended save states when signals
are delivered. This allows using AVX, MPX or PKRU registers in
signal handlers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel CPUs starting with Haswell-E implement a new MSR called
MSR_CORE_THREAD_COUNT which exposes the number of threads and cores
inside of a package.
This MSR is used by XNU to populate internal data structures and not
implementing it prevents virtual machines with more than 1 vCPU from
booting if the emulated CPU generation is at least Haswell-E.
This patch propagates the existing hvf logic from patch 027ac0cb51
("target/i386/hvf: add rdmsr 35H MSR_CORE_THREAD_COUNT") to TCG.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-Id: <20221004225643.65036-2-agraf@csgraf.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-27-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expand this function at each of its callers.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-26-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create a tcg global temp for this, and use it instead of explicit stores.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-25-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-24-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These functions have only one caller, and the logic is more
obvious this way.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-23-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These functions are always passed aflag, so we might as well
read it from DisasContext directly. While we're at it, use
a common subroutine for these two functions.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-22-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With gen_jmp_rel, we may chain between two translation blocks
which may only be separated because of TB size limits.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-21-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-20-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With gen_jmp_rel, we may chain to the next tb instead of merely
writing to eip and exiting. For repz, subtract cur_insn_len to
restart the current insn.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-19-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create a common helper for pc-relative branches. The jmp jb insn
was missing a mask for CODE32. In all cases the CODE64 check was
incorrectly placed, allowing PREFIX_DATA to truncate %rip to 16 bits.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-18-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can set is_jmp early, using only one if, and let that
be overwritten by gen_rep*'s calls to gen_jmp_tb.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-17-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create helpers for loading the address of the next insn.
Use tcg_constant_* in adjacent code where convenient.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-16-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use i32 not int or tl for eip and cs arguments.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-15-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the unused dest argument to gen_jr().
Remove most of the calls to gen_jr, and use DISAS_JUMP.
Remove some unused loads of eip for lcall and ljmp.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-14-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers pass s->base.pc_next and s->pc, which we can just
as well compute within the functions. Pull out common helpers
and reduce the amount of code under macros.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-13-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create common routines for computing the length of the insn.
Use tcg_constant_i32 in the new function, while we're at it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-12-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace lone calls to gen_eob() with the new enumerator.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-11-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace sequences of gen_update_cc_op, gen_update_eip_next,
and gen_eob with the new is_jmp enumerator.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-10-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set is_jmp properly in gen_movl_seg_T0, so that the callers
need to nothing special.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-9-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a few DISAS_TARGET_* aliases to reduce the number of
calls to gen_eob() and gen_eob_inhibit_irq(). So far,
only update i386_tr_translate_insn for exiting the block
because of single-step or previous inhibit irq.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-8-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sync EIP before exiting a translation block.
Replace all gen_jmp_im that use s->pc.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-7-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like gen_update_cc_op, sync EIP before doing something
that could raise an exception. Replace all gen_jmp_im
that use s->base.pc_next.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-6-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers pass s->base.pc_next and s->pc, which we can just as
well compute within the function. Adjust to use tcg_constant_i32
while we're at it.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-5-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers pass s->base.pc_next - s->cs_base, which we can just
as well compute within the function. Note the special case of
EXCP_VSYSCALL in which s->cs_base wasn't subtracted, but cs_base
is always zero in 64-bit mode, when vsyscall is used.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-4-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of returning the new pc, which is present in
DisasContext, return true if an insn was translated.
This is false when we detect a page crossing and must
undo the insn under translation.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221001140935.465607-3-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The DisasContext member and the disas_insn local variable of
the same name are identical to DisasContextBase.pc_next.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221001140935.465607-2-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The availability of tb->pc will shortly be conditional.
Introduce accessor functions to minimize ifdefs.
Pass around a known pc to places like tcg_gen_code,
where the caller must already have the value.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The "O" operand type in the Intel SDM needs to load an 8- to 64-bit
unsigned value, while insn_get is limited to 32 bits. Extract the code
out of disas_insn and into a separate function.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The later prefix wins if both are present, make it show in s->prefix too.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
INSERTQ is defined to not modify any bits in the lower 64 bits of the
destination, other than the ones being replaced with bits from the
source operand. QEMU instead is using unshifted bits from the source
for those bits.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many instructions which load/store 128-bit values are supposed to
raise #GP when the memory operand isn't 16-byte aligned. This includes:
- Instructions explicitly requiring memory alignment (Exceptions Type 1
in the "AVX and SSE Instruction Exception Specification" section of
the SDM)
- Legacy SSE instructions that load/store 128-bit values (Exceptions
Types 2 and 4).
This change sets MO_ALIGN_16 on 128-bit memory accesses that require
16-byte alignment. It adds cpu_record_sigbus and cpu_do_unaligned_access
hooks that simulate a #GP exception in qemu-user and qemu-system,
respectively.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/217
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ricky Zhou <ricky@rzhou.org>
Message-Id: <20220830034816.57091-2-ricky@rzhou.org>
[Do not bother checking PREFIX_VEX, since AVX is not supported. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now translator stops right *after* the end of a page, which
breaks reporting of fault locations when the last instruction of a
multi-insn translation block crosses a page boundary.
An implementation, like the one arm and s390x have, would require an
i386 length disassembler, which is burdensome to maintain. Another
alternative would be to single-step at the end of a guest page, but
this may come with a performance impact.
Fix by snapshotting disassembly state and restoring it after we figure
out we crossed a page boundary. This includes rolling back cc_op
updates and emitted ops.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1143
Message-Id: <20220817150506.592862-4-iii@linux.ibm.com>
[rth: Simplify end-of-insn cross-page checks.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Pass these along to translator_loop -- pc may be used instead
of tb->pc, and host_pc is currently unused. Adjust all targets
at one time.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The only user can easily use translator_lduw and
adjust the type to signed during the return.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
AVX includes an additional set of comparison predicates, some of which
our softfloat implementation does not expose as separate functions.
Rewrite the helpers in terms of floatN_compare for future extensibility.
Signed-off-by: Paul Brook <paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220424220204.2493824-24-paul@nowt.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a union to store the various possible kinds of function pointers, and
access the correct one based on the flags.
SSEOpHelper_table6 and SSEOpHelper_table7 right now only have one case,
but this would change with AVX's 3- and 4-argument operations. Use
unions there too, to keep the code more similar for the three tables.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For AVX we're going to need both 128 bit (xmm) and 256 bit (ymm) variants of
floating point helpers. Add the register type suffix to the existing
*PS and *PD helpers (SS and SD variants are only valid on 128 bit vectors)
No functional changes.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-15-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Put more flags to work to avoid hardcoding lists of opcodes. The op7 case
for SSE_OPF_CMP is included for homogeneity and because AVX needs it, but
it is never used by SSE or MMX.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle 3DNOW instructions early to avoid complicating the MMX/SSE logic.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-25-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a flags field each row in sse_op_table6 and sse_op_table7.
Initially this is only used as a replacement for the magic SSE41_SPECIAL
pointer. The other flags are mostly relevant for the AVX implementation
but can be applied to SSE as well.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-6-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a flags field to each row in sse_op_table1.
Initially this is only used as a replacement for the magic
SSE_SPECIAL and SSE_DUMMY pointers, the other flags are mostly
relevant for the AVX implementation but can be applied to SSE as well.
Signed-off-by: Paul Brook <paul@nowt.org>
Message-Id: <20220424220204.2493824-5-paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a convenience macro to get the address of an xmm_regs element within
CPUX86State.
This was originally going to be the basis of an implementation that broke
operations into 128 bit chunks. I scrapped that idea, so this is now a purely
cosmetic change. But I think a worthwhile one - it reduces the number of
function calls that need to be split over multiple lines.
No functional changes.
Signed-off-by: Paul Brook <paul@nowt.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220424220204.2493824-9-paul@nowt.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Write down explicitly the load/store sequence.
Extracted from a patch by Paul Brook <paul@nowt.org>.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The correct A20 masking is done if paging is enabled (protected mode) but it
seems to have been forgotten in real mode. For example from the AMD64 APM Vol. 2
section 1.2.4:
> If the sum of the segment base and effective address carries over into bit 20,
> that bit can be optionally truncated to mimic the 20-bit address wrapping of the
> 8086 processor by using the A20M# input signal to mask the A20 address bit.
Most BIOSes will enable the A20 line on boot, but I found by disabling the A20 line
afterwards, the correct wrapping wasn't taking place.
`handle_mmu_fault' in target/i386/tcg/sysemu/excp_helper.c seems to be the culprit.
In real mode, it fills the TLB with the raw unmasked address. However, for the
protected mode, the `mmu_translate' function does the correct A20 masking.
The fix then should be to just apply the A20 mask in the first branch of the if
statement.
Signed-off-by: Stephen Michael Jothen <sjothen@gmail.com>
Message-Id: <Yo5MUMSz80jXtvt9@air-old.local>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Coverity warns that 14 << data32 may overflow with respect
to the target_ulong to which it is subsequently added.
We know this wasn't true because data32 is in [1,2],
but the suggested fix is perfectly fine.
Fixes: Coverity CID 1487135, 1487256
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-Id: <20220401184635.327423-1-richard.henderson@linaro.org>
G_NORETURN was introduced in glib 2.68, fallback to G_GNUC_NORETURN in
glib-compat.
Note that this attribute must be placed before the function declaration
(bringing a bit of consistency in qemu codebase usage).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20220420132624.2439741-20-marcandre.lureau@redhat.com>
We have fetched and locked the logfile in translator_loop.
Pass the filepointer down to the disas_log hook so that it
need not be fetched and locked again.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-13-richard.henderson@linaro.org>
Inside qemu_log, we perform qemu_log_trylock/unlock, which need
not be done if we have already performed the lock beforehand.
Always check the result of qemu_log_trylock -- only checking
qemu_loglevel_mask races with the acquisition of the lock on
the logfile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-10-richard.henderson@linaro.org>
This function can fail, which makes it more like ftrylockfile
or pthread_mutex_trylock than flockfile or pthread_mutex_lock,
so rename it.
To closer match the other trylock functions, release rcu_read_lock
along the failure path, so that qemu_log_unlock need not be called
on failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-8-richard.henderson@linaro.org>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
High bits in the immediate operand of SSE comparisons are ignored, they
do not result in an undefined opcode exception. This is mentioned
explicitly in the Intel documentation.
Reported-by: sonicadvance1@gmail.com
Closes: https://gitlab.com/qemu-project/qemu/-/issues/184
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The instruction description says "It is loaded without rounding
errors." which implies we should have the widest rounding mode
possible.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/888
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220315121251.2280317-4-alex.bennee@linaro.org>
Loading a non-canonical address into rsp when handling an interrupt or
performing a far call should raise a #SS not a #GP.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/870
Signed-off-by: Gareth Webb <gareth.webb@umbralsoftware.co.uk>
Message-Id: <164529651121.25406.15337137068584246397-0@git.sr.ht>
[Move get_pg_mode to seg_helper.c for user-mode emulators. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LA57/PKE/PKS is only relevant in 64-bit mode, and NXE is only relevant if
PAE is in use. Since there is code that checks PG_MODE_LA57 to determine
the canonicality of addresses, make sure that the bit is not set by
mistake in 32-bit mode. While it would not be a problem because 32-bit
addresses by definition fit in both 48-bit and 57-bit address spaces,
it is nicer if get_pg_mode() actually returns whether a feature is enabled,
and it allows a few simplifications in the page table walker.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
excp_helper.c requires "exec/exec-all.h" for tlb_set_page_with_attrs()
and misc_helper.c for tlb_flush().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-8-f4bug@amsat.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I think these have been wrong since f193c7979c (do not depend on
thunk.h - more log items). Fix them so as not to confuse other
debugging.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220204204335.1689602-26-alex.bennee@linaro.org>
Renaming defines for quad in their various forms so that their signedness is
now explicit.
Done using git grep as suggested by Philippe, with a bit of hand edition to
keep assignments aligned.
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220106210108.138226-2-frederic.petrot@univ-grenoble-alpes.fr
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In the SSE decode function gen_sse(), we combine a byte
'b' and a value 'b1' which can be [0..3], and switch on them:
b |= (b1 << 8);
switch (b) {
...
default:
unknown_op:
gen_unknown_opcode(env, s);
return;
}
In three cases inside this switch, we were then also checking for
"if (b1 >= 2) { goto unknown_op; }".
However, this can never happen, because the 'case' values in each place
are 0x0nn or 0x1nn and the switch will have directed the b1 == (2, 3)
cases to the default already.
This check was added in commit c045af25a5 in 2010; the added code
was unnecessary then as well, and was apparently intended only to
ensure that we never accidentally ended up indexing off the end
of an sse_op_table with only 2 entries as a result of future bugs
in the decode logic.
Change the checks to assert() instead, and make sure they're always
immediately before the array access they are protecting.
Fixes: Coverity CID 1460207
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
mmu_translate is supposed to return an error code for page faults; it is
not able to handle other exceptions. The #GP case for noncanonical
virtual addresses is not handled correctly, and incorrectly raised as
a page fault with error code 1. Since it cannot happen for nested
page tables, move it directly to handle_mmu_fault, even before the
invocation of mmu_translate.
Fixes: #676
Fixes: 661ff4879e ("target/i386: extract mmu_translate", 2021-05-11)
Cc: qemu-stable@nongnu.org
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Correctly look up the paging mode of the hypervisor when it is using 64-bit
mode but the guest is not.
Fixes: 68746930ae ("target/i386: use mmu_translate for NPT walk", 2021-05-11)
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Record cr2, error_code, and exception_index. That last means
that we must exit to cpu_loop ourselves, instead of letting
exception_index being overwritten.
Use the maperr parameter to properly set PG_ERROR_P_MASK.
Reviewed by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We were using singlestep_enabled as a proxy for whether
translator_use_goto_tb would always return false.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We're about to move this out of tcg.h, so rename it
as we did when moving MemOp.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Following the logic of commit 30493a030f ("i386: split seg_helper
into user-only and sysemu parts"), move x86_cpu_exec_interrupt()
under sysemu/seg_helper.c.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-By: Warner Losh <imp@bsdimp.com>
Message-Id: <20210911165434.531552-12-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Restrict cpu_exec_interrupt() and its callees to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-11-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
do_interrupt() is sysemu specific. However due to some X86
specific hack, it is also used in user-mode emulation, which
is why it couldn't be restricted to CONFIG_SOFTMMU (see the
comment around added in commit 7827168471: "cpu: tcg_ops:
move to tcg-cpu-ops.h, keep a pointer in CPUClass").
Keep the hack but rename the handler as fake_user_interrupt()
and restrict do_interrupt() to sysemu.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-6-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Merge two TARGET_X86_64 consecutive blocks.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210911165434.531552-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
[rth: Split out of a larger patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The feature allows the VMSAVE and VMLOAD instructions to execute in guest mode without
causing a VMEXIT. (APM2 15.33.1)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Writes to cr8 affect v_tpr. This could set or unset an interrupt
request as the priority might have changed.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APM2 states that if V_IGN_TPR is nonzero, the current
virtual interrupt ignores the (virtual) TPR.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VGIF provides masking capability for when virtual interrupts
are taken. (APM2)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Moved int_ctl into the CPUX86State structure. It removes some
unnecessary stores and loads, and prepares for tracking the vIRQ
state even when it is masked due to vGIF.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VGIF allows STGI and CLGI to execute in guest mode and control virtual
interrupts in guest mode.
When the VGIF feature is enabled then:
* executing STGI in the guest sets bit 9 of the VMCB offset 60h.
* executing CLGI in the guest clears bit 9 of the VMCB offset 60h.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210730070742.9674-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
APM2 requires that VMRUN and VMLOAD canonicalize (sign extend to 63
from 48/57) all base addresses in the segment registers that have been
respectively loaded.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210804113058.45186-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
~0UL has 64 bits on Linux and 32 bits on Windows.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/512
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210812111056.26926-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The shift constant was incorrect, causing int_prio to always be zero.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
[Rewritten commit message since v1 had already been included. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMRUN exits with SVM_EXIT_ERR if either:
* The event injected has a reserved type.
* When the event injected is of type 3 (exception), and the vector that
has been specified does not correspond to an exception.
This does not fix the entire exc_inj test in kvm-unit-tests.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210725090855.19713-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some cpu properties have to be set only for cpu models in builtin_x86_defs,
registered with x86_register_cpu_model_type, and not for
cpu models "base", "max", and the subclass "host".
These properties are the ones set by function x86_cpu_apply_props,
(also including kvm_default_props, tcg_default_props),
and the "vendor" property for the KVM and HVF accelerators.
After recent refactoring of cpu, which also affected these properties,
they were instead set unconditionally for all x86 cpus.
This has been detected as a bug with Nested on AMD with cpu "host",
as svm was not turned on by default, due to the wrongful setting of
kvm_default_props via x86_cpu_apply_props, which set svm to "off".
Rectify the bug introduced in commit "i386: split cpu accelerators"
and document the functions that are builtin_x86_defs-only.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: f5cc5a5c ("i386: split cpu accelerators from cpu.c,"...)
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/477
Message-Id: <20210723112921.12637-1-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All MBZ in CR3 must be zero (APM2 15.5)
Added checks in both helper_vmrun and helper_write_crN.
When EFER.LMA is zero the upper 32 bits needs to be zeroed.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210723112740.45962-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EFER.SVME has to be set, and EFER reserved bits must
be zero.
In addition the combinations
* EFER.LMA or EFER.LME is non-zero and the processor does not support LM
* non-zero EFER.LME and CR0.PG and zero CR4.PAE
* non-zero EFER.LME and CR0.PG and zero CR0.PE
* non-zero EFER.LME, CR0.PG, CR4.PAE, CS.L and CS.D
are all invalid.
(AMD64 Architecture Programmer's Manual, V2, 15.5)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-3-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All MBZ bits in CR4 must be zero. (APM2 15.5)
Added reserved bitmask and added checks in both
helper_vmrun and helper_write_crN.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-2-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APM2 states that The processor takes a virtual INTR interrupt
if V_IRQ and V_INTR_PRIO indicate that there is a virtual interrupt pending
whose priority is greater than the value in V_TPR.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210721152651.14683-1-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The hook is now unused, with breakpoints checked outside translation.
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Return false for RF set, as we do in i386_tr_breakpoint_check.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Always provide the atomic interface using TCGMemOpIdx oi
and uintptr_t retaddr. Rename from helper_* to cpu_* so
as to (mostly) match the exec/cpu_ldst.h functions, and
to emphasize that they are not callable from TCG directly.
Tested-by: Cole Robinson <crobinso@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Update FCS:FIP and FDS:FDP according to the Intel Manual Vol.1 8.1.8.
Note that CPUID.(EAX=07H,ECX=0H):EBX[bit 13] is not implemented by
design in this patch and will be added along with TCG features flag
in a separate patch later.
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Message-Id: <20210530150112.74411-2-ziqiaokong@gmail.com>
[rth: Push FDS/FDP handling down into mod != 3 case; free last_addr.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Do not call helper_fninit directly from helper_xrstor.
Do call the new helper from do_fsave.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A new pair of braces has to be added to declare variables in the case block.
The code style is also fixed according to the transalte.c itself during the
code motion.
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Message-Id: <20210530150112.74411-1-ziqiaokong@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since cpu_breakpoint and cpu_watchpoint are in a union,
the code should access only one of them.
Signed-off-by: Dmitry Voronetskiy <davoronetskiy@gmail.com>
Message-Id: <20210613180838.21349-1-davoronetskiy@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The loop is performing a simple boolean test for the existence
of a BP_CPU breakpoint at EIP. Plus it gets the iteration wrong,
if we happen to have a BP_GDB breakpoint at the same address.
We have a function for this: cpu_breakpoint_test.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20210620062317.1399034-1-richard.henderson@linaro.org>
Just use translator_use_goto_tb directly at the one call site,
rather than maintaining a local wrapper.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The root trace-events only declares a single TCG event:
$ git grep -w tcg trace-events
trace-events:115:# tcg/tcg-op.c
trace-events:137:vcpu tcg guest_mem_before(TCGv vaddr, uint16_t info) "info=%d", "vaddr=0x%016"PRIx64" info=%d"
and only a tcg/tcg-op.c uses it:
$ git grep -l trace_guest_mem_before_tcg
tcg/tcg-op.c
therefore it is pointless to include "trace-tcg.h" in each target
(because it is not used). Remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210629050935.2570721-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use raise_exception_ra (without error code) when raising the illegal
opcode operation; raise #GP when setting bits 63:32 of DR6 or DR7.
Move helper_get_dr to sysemu/ since it is a privileged instruction
that is not needed on user-mode emulators.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR6[63:32] and DR7[63:32] are reserved and need to be zero.
(AMD64 Architecture Programmer's Manual, V2, 15.5)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210705081802.18960-3-laramglazier@gmail.com>
[Ignore for 32-bit builds. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The address of the last entry in the MSRPM and
in the IOPM must be smaller than the largest physical address.
(APM2 15.10-15.11)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210705081802.18960-2-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Given that TCG is now the only consumer of X86XSaveArea, move the
structure definition and associated offset declarations and checks to a
TCG specific header.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210705104632.2902400-9-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than relying on the X86XSaveArea structure definition,
determine the offset of XSAVE state areas using CPUID leaf 0xd where
possible (KVM and HVF).
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20210705104632.2902400-8-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a break instead of an ifdefed else.
There's no need to move the values through s->T0.
Remove TCG_BSWAP_IZ and the preceding zero-extension.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Implement the new semantics in the fallback expansion.
Change all callers to supply the flags that keep the
semantics unchanged locally.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When the selective CR0 write intercept is set, all writes to bits in
CR0 other than CR0.TS or CR0.MP cause a VMEXIT.
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210616123907.17765-5-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The combination of unset CD and set NW bit in CR0 is illegal.
CR0[63:32] are also reserved and need to be zero.
(AMD64 Architecture Programmer's Manual, V2, 15.5)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210616123907.17765-4-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Zero VMRUN intercept and ASID should cause an immediate VMEXIT
during the consistency checks performed by VMRUN.
(AMD64 Architecture Programmer's Manual, V2, 15.5)
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210616123907.17765-3-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added cpu_svm_has_intercept to reduce duplication when checking the
corresponding intercept bit outside of cpu_svm_check_intercept_param
Signed-off-by: Lara Lazier <laramglazier@gmail.com>
Message-Id: <20210616123907.17765-2-laramglazier@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A recent cleanup did not recognize that there are two ways
to encode cr8: one via the LOCK and the other via REX.
Fixes: 7eff2e7c
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/380
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210602035511.96834-1-richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The format of the task state segment is governed by bit 3 in the
descriptor type field. On a task switch, the format for saving
is given by the current value of TR's type field, while the
format for loading is given by the new descriptor.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the manual, the high 16-bit of the registers are preserved
when switching to a 16-bit task. Implement this in switch_tss_ra.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TSS offsets in the manuals have only 2-byte slots for the
segment registers. QEMU incorrectly uses 4-byte slots, so
that SS overlaps the LDT selector.
Resolves: #382
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use an enumeration instead of raw 32/64/80 values.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We no longer have any runtime modifications to this struct,
so declare them all const.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20210227232519.222663-3-richard.henderson@linaro.org>
tb_gen_code() assumes that tb->size must never be zero, otherwise it
may produce spurious exceptions. For x86_64 this may happen when
creating a translation block for the vsyscall page.
Fix by pretending that vsyscall translation blocks have at least one
instruction.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210519045738.1335210-2-iii@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
With the previous patch for check_io, we now have enough for
the compiler to dead-code eliminate all of the i/o helpers.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-51-richard.henderson@linaro.org>
The we never allow i/o from user-only, and the tss check
that helper_check_io does will always fail. Use an ifdef
within gen_check_io and return false, indicating that an
exception is known to be raised.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-50-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Drop helper_check_io[bwl] and expose their common
subroutine to tcg directly.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210514151342.384376-49-richard.henderson@linaro.org>
Pass in a pre-truncated TCGv_i32 value. We were doing the
truncation of EDX in multiple places, now only once per insn.
While all callers use s->tmp2_i32, for cleanliness of the
subroutine, use a parameter anyway.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-48-richard.henderson@linaro.org>
Get cur_eip from DisasContext. Do not require the caller
to use svm_is_rep; get prefix from DisasContext. Use the
proper symbolic constants for SVM_IOIO_*.
While we're touching all call sites, return bool in
preparation for gen_check_io raising #GP.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-47-richard.henderson@linaro.org>
At minimum, wrmsr can change efer, which affects HF_LMA.
Cc: qemu-stable@nongnu.org
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-46-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-45-richard.henderson@linaro.org>
The user-version is a no-op. This lets us completely
remove tcg/user/svm_stubs.c.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-44-richard.henderson@linaro.org>
Use a single helper, flush_page, to do the work.
Use gen_svm_check_intercept.
Perform the zero-extension for invlpga inline.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-43-richard.henderson@linaro.org>
These instructions are all privileged.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-42-richard.henderson@linaro.org>
Having the callers upcast to X86CPU is a waste, since we
don't need it. We even have to recover env in do_hlt.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-41-richard.henderson@linaro.org>
Pull the svm intercept check into the translator.
Pull the entire implementation of lmsw into the translator.
Push the check for CR8LEG into the regno validation switch.
Unify the gen_io_start check between read/write.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210514151342.384376-40-richard.henderson@linaro.org>
This function is only called from tcg/sysemu/.
There is no need for a stub in tcg/user/.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-39-richard.henderson@linaro.org>
When exiting helper_svm_check_intercept via exception, cpu_vmexit
calls cpu_restore_state, which will recover eip and cc_op via unwind.
Therefore we do not need to store eip or cc_op before the call.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-38-richard.henderson@linaro.org>
The param argument to helper_svm_check_intercept_param is always 0;
eliminate it and rename to helper_svm_check_intercept. Fold
gen_svm_check_intercept_param into gen_svm_check_intercept.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-37-richard.henderson@linaro.org>
Both invocations pass the start of the current instruction,
which is available as s->base.pc_next. The function sets
is_jmp, so we can eliminate a second setting.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-36-richard.henderson@linaro.org>
Any helper that always raises an exception or interrupt,
or simply exits to the main loop, can be so marked.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-35-richard.henderson@linaro.org>
Use STUB_HELPER to ensure that such calls are always eliminated.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-34-richard.henderson@linaro.org>
Our sysemu implementation is a stub. We can already intercept
instructions for vmexit, and raising #UD is trivial.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-33-richard.henderson@linaro.org>
For user-only, we do not need to check for VMM intercept.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-32-richard.henderson@linaro.org>
Most of the VMM instructions are already disabled for user-only,
by being usable only from ring 0.
The spec is intentionally loose for VMMCALL, allowing the VMM to
define syscalls for user-only. However, we're not emulating any
VMM, so VMMCALL can just raise #UD unconditionally.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210514151342.384376-31-richard.henderson@linaro.org>
This removes an ifdef from the middle of disas_insn,
and ensures that the branch is not reachable.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-30-richard.henderson@linaro.org>
Sort all of the single-byte members to the same area
of the structure, eliminating 8 bytes of padding.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-29-richard.henderson@linaro.org>
After fixing a typo in the comment, fixup for CODING_STYLE.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210514151342.384376-28-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-27-richard.henderson@linaro.org>
It's just as easy to clear the flag with AND than assignment.
In two cases the test for the bit can be folded together with
the test for HF_INHIBIT_IRQ_MASK.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-26-richard.henderson@linaro.org>
Both of these fields store the size of a single memory access,
so the range of values is 0-8.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-25-richard.henderson@linaro.org>
Currently, vex_l is either {0,1}; if in the future we implement
AVX-512, the max value will be 2. In vex_v we store a register
number. This is 0-15 for SSE, and 0-31 for AVX-512.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-24-richard.henderson@linaro.org>
The highest bit in this set is 0x40 (PREFIX_REX).
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-23-richard.henderson@linaro.org>
The range of values is -1 (none) to 5 (R_GS).
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-22-richard.henderson@linaro.org>
The value comes from tb->flags, which is uint32_t.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-21-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-20-richard.henderson@linaro.org>
Treat this flag exactly like we treat the other rex bits.
The -1 initialization is unused; the two tests are > 0 and == 1,
so the value can be reduced to a bool.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-19-richard.henderson@linaro.org>
Treat this flag exactly like we treat rex_b and rex_x.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-18-richard.henderson@linaro.org>
Change the storage from int to uint8_t since the value is in {0,8}.
For x86_64 add 0 in the macros to (1) promote the type back to int,
and (2) make the macro an rvalue.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-17-richard.henderson@linaro.org>
The existing flag, x86_64_hregs, does not accurately describe
its setting. It is true if and only if a REX prefix has been
seen. Yes, that affects the "h" regs, but that's secondary.
Add PREFIX_REX and include this bit in s->prefix. Add REX_PREFIX
so that the check folds away when x86_64 is compiled out.
Fold away the reg >= 8 check, because bit 3 of the register
number comes from the REX prefix in the first place.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-16-richard.henderson@linaro.org>
LMA disables traditional segmentation, exposing a flat address space.
This means that ADDSEG is off.
Since we're adding an accessor macro, pull the value directly out
of flags otherwise.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-15-richard.henderson@linaro.org>
LMA is a pre-requisite for CODE64, so there is no way to disable it
for x86_64-linux-user, and there is no way to enable it for i386.
Since we're adding an accessor macro, pull the value directly out
of flags when we're not assuming a constant.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-14-richard.henderson@linaro.org>
For x86_64 user-only, there is no way to leave 64-bit mode.
Without x86_64, there is no way to enter 64-bit mode. There is
an existing macro to aid with that; simply place it in the right
place in the ifdef chain.
Since we're adding an accessor macro, pull the value directly out
of flags when we're not assuming a constant.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-13-richard.henderson@linaro.org>
For user-only, SS32 == !VM86, because we are never in
real-mode. Since we cannot enter vm86 mode for x86_64
user-only, SS32 is always set.
Since we're adding an accessor macro, pull the value
directly out of flags otherwise.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-12-richard.henderson@linaro.org>
For user-only, CODE32 == !VM86, because we are never in real-mode.
Since we cannot enter vm86 mode for x86_64 user-only, CODE32 is
always set.
Since we're adding an accessor macro, pull the value directly out
of flags otherwise.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-11-richard.henderson@linaro.org>
For i386-linux-user, we can enter vm86 mode via the vm86(2) syscall.
That syscall explicitly returns to 32-bit mode, and the syscall does
not exist for a 64-bit x86_64 executable.
Since we're adding an accessor macro, pull the value directly out of
flags otherwise.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-10-richard.henderson@linaro.org>
On real hardware, the linux kernel has the iopl(2) syscall which
can set IOPL to 3, to allow e.g. the xserver to briefly disable
interrupts while programming the graphics card.
However, QEMU cannot and does not implement this syscall, so the
IOPL is never changed from 0. Which means that all of the checks
vs CPL <= IOPL are false for user-only.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-9-richard.henderson@linaro.org>
A user-mode executable always runs in ring 3.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-8-richard.henderson@linaro.org>
A user-mode executable is never in real-mode. Since we're adding
an accessor macro, pull the value directly out of flags for sysemu.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-7-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-6-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-5-richard.henderson@linaro.org>
In vm86 mode, we use the same helper as real-mode, but with
an extra check for IOPL. All non-exceptional paths set EFLAGS.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-4-richard.henderson@linaro.org>
Split out the check for CPL != 0 and the raising of #GP.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-3-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210514151342.384376-2-richard.henderson@linaro.org>
Unify the duplicate code between get_hphys and mmu_translate, by simply
making get_hphys call mmu_translate. This also fixes the support for
5-level nested page tables.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to unify the two stages of page table lookup, we need
mmu_translate to use either the host CR0/EFER/CR4 or the guest's.
To do so, make mmu_translate use the same pg_mode constants that
were used for the NPT lookup.
This also prepares for adding 5-level NPT support, which however does
not work yet.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the page table lookup out of handle_mmu_fault, which only has
to invoke mmu_translate and either fill the TLB or deliver the page
fault.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will reuse the page walker for both SVM and regular accesses. To do
so we will build a function that receives the currently active paging
mode; start by including in cpu.h the constants and the function to go
from cr4/hflags/efer to the paging mode.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
while on x86 all CPU classes can use the same set of TCGCPUOps,
on ARM the right accel behavior depends on the type of the CPU.
So we need a way to specialize the accel behavior according to
the CPU. Therefore, add a second initialization, after the
accel_cpu->cpu_class_init, that allows to do this.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210322132800.7470-24-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For now we just copy over the previous user stubs, but really,
everything that requires s->cpl == 0 should be impossible
to trigger from user-mode emulation.
Later on we should add a check that asserts this easily f.e.:
static bool check_cpl0(DisasContext *s)
{
int cpl = s->cpl;
#ifdef CONFIG_USER_ONLY
assert(cpl == 3);
#endif
if (cpl != 0) {
gen_exception(s, EXCP0D_GPF, s->pc_start - s->cs_base);
return false;
}
return true;
}
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-17-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
create a separate tcg/sysemu/fpu_helper.c for the sysemu-only parts.
For user mode, some small #ifdefs remain in tcg/fpu_helper.c
which do not seem worth splitting into their own user-mode module.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-16-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
for user-mode, assert that the hidden IOBPT flags are not set
while attempting to generate io_bpt helpers.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-14-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
smm is only really useful for sysemu, split in two modules
around the CONFIG_USER_ONLY, in order to remove the ifdef
and use the build system instead.
add cpu_abort() when detecting attempts to enter SMM mode via
SMI interrupt in user-mode, and assert that the cpu is not
in SMM mode while translating RSM instructions.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-12-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
overall, all devices' realize functions take an Error **errp, but return void.
hw/core/qdev.c code, which realizes devices, therefore does:
local_err = NULL;
dc->realize(dev, &local_err);
if (local_err != NULL) {
goto fail;
}
However, we can improve at least accel_cpu to return a meaningful bool value.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210322132800.7470-9-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
i386 is the first user of AccelCPUClass, allowing to split
cpu.c into:
cpu.c cpuid and common x86 cpu functionality
host-cpu.c host x86 cpu functions and "host" cpu type
kvm/kvm-cpu.c KVM x86 AccelCPUClass
hvf/hvf-cpu.c HVF x86 AccelCPUClass
tcg/tcg-cpu.c TCG x86 AccelCPUClass
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[claudio]:
Rebased on commit b8184135 ("target/i386: allow modifying TCG phys-addr-bits")
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210322132800.7470-5-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The helper_* functions must use GETPC() to unwind from TCG.
The cpu_x86_* functions cannot, and directly calling the
helper_* functions is a bug. Split out new functions that
perform the work and can be used by both.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Tested-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210322132800.7470-4-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change the prefix from "helper" to "do". The former should be
reserved for those functions that are called from TCG; the latter
is in use within the file already for those functions that are
called from the helper functions, adding a "retaddr" argument.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Tested-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210322132800.7470-3-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
