On SiFive FU540 SoC, the value stored at physical address 0x1000
stores the MSEL pin state that is used to control the next boot
location that ROM codes jump to.
Add a new property msel to sifive_u machine for this.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-12-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In prepration to add more properties to this machine, rename the
existing serial property get/set functions to a generic name.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-11-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The HiFive Unleashed board wires GPIO pin#10 to the input of the
system reset signal. Let's set up the GPIO pin#10 and insert a
"gpio-restart" device tree node so that reboot is now functional
with QEMU 'sifive_u' machine.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-10-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the GPIO output IRQs are triggered each time any GPIO
register is written. However this is not correct. We should only
trigger the output IRQ when the pin is configured as output enable.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-9-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a GPIO controller with 16 GPIO lines.
This hooks the exsiting SiFive GPIO model to the SoC, and adds its
device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-8-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a new property to represent the number of GPIO pins supported
by the GPIO controller.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-7-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Do various minor clean-ups to the exisiting codes for:
- coding convention conformance
- remove unnecessary blank lines
- spell SiFive correctly
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-6-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Upstream U-Boot v2020.07 codes switch to access SiFive FU540 OTP
based on device tree information. Let's generate the device tree
node for OTP.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-5-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is no need to retrieve all PLIC IRQ information in order to
just connect the GEM IRQ. Use qdev_get_gpio_in() directly like
what is done for other peripherals.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-4-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but opentitan codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-3-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was done in the virt & sifive_u codes, but sifive_e codes were
missed. Remove the riscv_ prefix of the machine* and soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1591625864-31494-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1591625864-31494-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is the initial commit of the Ibex UART device. Serial TX is
working, while RX has been implemeneted but untested.
This is based on the documentation from:
https://docs.opentitan.org/hw/ip/uart/doc/
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
This is the same transformation as in the previous commit, except
sysbus_init_child_obj() and realize are too separated for the commit's
Coccinelle script to handle, typically because sysbus_init_child_obj()
is in a device's instance_init() method, and the matching realize is
in its realize() method.
Perhaps a Coccinelle wizard could make it transform that pattern, but
I'm just a bungler, and the best I can do is transforming the two
separate parts separately:
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(OBJECT(child), true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression errp;
expression child;
symbol true;
@@
- object_property_set_bool(child, true, "realized", errp);
+ sysbus_realize(SYS_BUS_DEVICE(child), errp);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
@@
- qdev_init_nofail(DEVICE(child));
+ sysbus_realize(SYS_BUS_DEVICE(child), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
expression dev;
@@
dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression child;
identifier dev;
@@
DeviceState *dev = DEVICE(child);
...
- qdev_init_nofail(dev);
+ sysbus_realize(SYS_BUS_DEVICE(dev), &error_fatal);
// only correct with a matching sysbus_init_child_obj() transformation!
@@
expression parent, name, size, type;
expression child;
symbol true;
@@
- sysbus_init_child_obj(parent, name, child, size, type);
+ sysbus_init_child_XXX(parent, name, child, size, type);
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, child, sizeof(*child), type)
+ object_initialize_child(parent, propname, child, type)
@@
expression parent, propname, type;
expression child;
@@
- sysbus_init_child_XXX(parent, propname, &child, sizeof(child), type)
+ object_initialize_child(parent, propname, &child, type)
This script is *unsound*: we need to manually verify init and realize
conversions are properly paired.
This commit has only the pairs where object_initialize_child()'s
@child and sysbus_realize()'s @dev argument text match exactly within
the same source file.
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-49-armbru@redhat.com>
The callers of object_initialize_child() commonly pass either
&child, sizeof(child), or pchild, sizeof(*pchild). Tidy up the few
that don't, mostly to keep the next commit simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-36-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is somewhere between
not worthwhile and infeasible (at least for me).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-11-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
riscv_sifive_e_soc_init(), riscv_sifive_u_soc_init(),
spike_board_init(), spike_v1_10_0_board_init(),
spike_v1_09_1_board_init(), and riscv_virt_board_init() create
"riscv-hart_array" sysbus devices in a way that leaves them unplugged.
Create them the common way that puts them into the main system bus.
Affects machines sifive_e, sifive_u, spike, spike_v1.10, spike_v1.9.1,
and virt. Visible in "info qtree", here's the change for sifive_e:
bus: main-system-bus
type System
+ dev: riscv.hart_array, id ""
+ num-harts = 1 (0x1)
+ hartid-base = 0 (0x0)
+ cpu-type = "sifive-e31-riscv-cpu"
dev: sifive_soc.gpio, id ""
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200609122339.937862-20-armbru@redhat.com>
This adds a barebone OpenTitan machine to QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The ISA specific Spike machines have been deprecated in QEMU since 4.1,
let's finally remove them.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Remove the riscv_ prefix of the machine* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1590072147-13035-2-git-send-email-bmeng.cn@gmail.com
Message-Id: <1590072147-13035-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To keep consistency with the machine* functions, remove the riscv_
prefix of the soc* functions.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1590072147-13035-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1590072147-13035-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per QEMU deprecated doc, QEMU 4.1 introduced support for the -bios
option in QEMU for RISC-V for the virt machine and sifive_u machine.
The default behavior has been that QEMU does not automatically load
any firmware if no -bios option is included.
Now 2 releases passed, it's time to change the default behavior to
load the default OpenSBI firmware automatically. The firmware is
included with the QEMU release and no user interaction is required.
All a user needs to do is specify the kernel they want to boot with
the -kernel option.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1588335545-649-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1588335545-649-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We only ship plain binary bios images in the QEMU source. With Spike
machine that uses ELF images as the default bios, running QEMU test
will complain hence let's suppress the error report for QEMU testing.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <1588348254-7241-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use the QEMU_IS_ALIGNED() macro to verify the flash block size
is properly aligned. It is quicker to process when reviewing.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200511205246.24621-1-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
object_property_set_description() and
object_class_property_set_description() fail only when property @name
is not found.
There are 85 calls of object_property_set_description() and
object_class_property_set_description(). None of them can fail:
* 84 immediately follow the creation of the property.
* The one in spapr_rng_instance_init() refers to a property created in
spapr_rng_class_init(), from spapr_rng_properties[].
Every one of them still gets to decide what to pass for @errp.
51 calls pass &error_abort, 32 calls pass NULL, one receives the error
and propagates it to &error_abort, and one propagates it to
&error_fatal. I'm actually surprised none of them violates the Error
API.
What are we gaining by letting callers handle the "property not found"
error? Use when the property is not known to exist is simpler: you
don't have to guard the call with a check. We haven't found such a
use in 5+ years. Until we do, let's make life a bit simpler and drop
the @errp parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-8-armbru@redhat.com>
[One semantic rebase conflict resolved]
Currently, the upstream Spike ISA simulator allows more than
one CPUs so we update QEMU Spike machine on similar lines to
allow more than one CPUs.
The maximum number of CPUs for QEMU Spike machine is kept
same as QEMU Virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200427080644.168461-4-anup.patel@wdc.com
Message-Id: <20200427080644.168461-4-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_firmware() which provides the possibility to access
the symbol table during kernel loading.
The pointer is ignored, if supplied with flat (non-elf) firmware image.
The Spike board requires it locate the HTIF symbols from firmware ELF
passed via "-bios" option.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200427080644.168461-2-anup.patel@wdc.com
Message-Id: <20200427080644.168461-2-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Allows the CPU to be changed from the default via the -cpu command
line option.
Signed-off-by: Corey Wharton <coreyw7@fb.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200313193429.8035-2-coreyw7@fb.com
Message-Id: <20200313193429.8035-2-coreyw7@fb.com>
[ Changes by AF:
- Set "cpu-type" from the machine and not SoC
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
32-bit machine should have its CPU's "mmu-type" set to "riscv,sv32".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1583585319-26603-1-git-send-email-bmeng.cn@gmail.com
Message-Id: <1583585319-26603-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the board serial number is hard-coded to 1, and passed
to OTP model during initialization. Firmware (FSBL, U-Boot) uses
the serial number to generate a unique MAC address for the on-chip
ethernet controller. When multiple QEMU 'sifive_u' instances are
created and connected to the same subnet, they all have the same
MAC address hence it creates a unusable network.
A new "serial" property is introduced to specify the board serial
number. When not given, the default serial number 1 is used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1573916930-19068-1-git-send-email-bmeng.cn@gmail.com>
[ Changed by AF:
- Use the SoC's serial property to pass the info to the SoC
- Fixup commit title
- Rebase on file restructuring
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the board serial number is hard-coded to 1, and passed
to OTP model during initialization. Firmware (FSBL, U-Boot) uses
the serial number to generate a unique MAC address for the on-chip
ethernet controller. When multiple QEMU 'sifive_u' instances are
created and connected to the same subnet, they all have the same
MAC address hence it creates a unusable network.
A new "serial" property is introduced to the sifive_u SoC to specify
the board serial number. When not given, the default serial number
1 is used.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Split the file into clear machine and SoC sections.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes the following coccinelle warnings:
$ spatch --sp-file --verbose-parsing ... \
scripts/coccinelle/remove_local_err.cocci
...
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5213
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5261
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:166
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:167
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:169
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:170
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:171
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:173
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5787
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5789
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5800
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5801
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5802
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5804
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5805
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5806
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:6329
SUSPICIOUS: a \ character appears outside of a #define at ./hw/sd/sdhci.c:1133
SUSPICIOUS: a \ character appears outside of a #define at ./hw/scsi/scsi-disk.c:3081
SUSPICIOUS: a \ character appears outside of a #define at ./hw/net/virtio-net.c:1529
SUSPICIOUS: a \ character appears outside of a #define at ./hw/riscv/sifive_u.c:468
SUSPICIOUS: a \ character appears outside of a #define at ./dump/dump.c:1895
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2209
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2215
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2221
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2222
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:173
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200412223619.11284-2-f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
* get/set_uint cleanups (Felipe)
* Lock guard support (Stefan)
* MemoryRegion ownership cleanup (Philippe)
* AVX512 optimization for buffer_is_zero (Robert)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJecOZiAAoJEL/70l94x66DgGkH/jpY4IgqlSAAWCgaxfe1n1vg
ahSzSLrC8wiJq2Jxbmxn+5BbH6BxQ9ibflsY5bvCY/sTb7UlOFCPkFhQ2iUgplkw
ciB5UfgCA6OHpKEhpHhXtzlybtNOlxXNWYJ1SrcVXbRES8f7XdhMKs15mnJJuOOE
k/tuZo/44yZRJl0Cv+nkvIFcCVgyu1q0Lln/1MMPngY2r9gt893cY9feTBSSWgnp
+7HZr5TXI7mcIytczFKzbdujlG4391DGejKX66IIxGcWg9vXS7TwAStzH1vSKVfJ
73SKZBoCU5gpHHHC+dqVyouMerV+UE+WQPNtF+LCsNgJBw/2NXc1ZgDrtz1OI2c=
=+LRX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Bugfixes all over the place
* get/set_uint cleanups (Felipe)
* Lock guard support (Stefan)
* MemoryRegion ownership cleanup (Philippe)
* AVX512 optimization for buffer_is_zero (Robert)
# gpg: Signature made Tue 17 Mar 2020 15:01:54 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (62 commits)
hw/arm: Let devices own the MemoryRegion they create
hw/arm: Remove unnecessary memory_region_set_readonly() on ROM alias
hw/ppc/ppc405: Use memory_region_init_rom() with read-only regions
hw/arm/stm32: Use memory_region_init_rom() with read-only regions
hw/char: Let devices own the MemoryRegion they create
hw/riscv: Let devices own the MemoryRegion they create
hw/dma: Let devices own the MemoryRegion they create
hw/display: Let devices own the MemoryRegion they create
hw/core: Let devices own the MemoryRegion they create
scripts/cocci: Patch to let devices own their MemoryRegions
scripts/cocci: Patch to remove unnecessary memory_region_set_readonly()
scripts/cocci: Patch to detect potential use of memory_region_init_rom
hw/sparc: Use memory_region_init_rom() with read-only regions
hw/sh4: Use memory_region_init_rom() with read-only regions
hw/riscv: Use memory_region_init_rom() with read-only regions
hw/ppc: Use memory_region_init_rom() with read-only regions
hw/pci-host: Use memory_region_init_rom() with read-only regions
hw/net: Use memory_region_init_rom() with read-only regions
hw/m68k: Use memory_region_init_rom() with read-only regions
hw/display: Use memory_region_init_rom() with read-only regions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid orphan memory regions being added in the /unattached QOM
container.
This commit was produced with the Coccinelle script
scripts/coccinelle/memory-region-housekeeping.cocci.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This commit was produced with the Coccinelle script
scripts/coccinelle/memory-region-housekeeping.cocci.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Update BIOS_FILENAME to consider 32-bit bios image file name.
Tested booting Linux v5.5 32-bit image (built from rv32_defconfig
plus CONFIG_SOC_SIFIVE) with the default 32-bit bios image.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This pull request is almost entirely an implementation of the draft hypervisor
extension. This extension is still in draft and is expected to have
incompatible changes before being frozen, but we've had good luck managing
other RISC-V draft extensions in QEMU so far.
Additionally, there's a fix to PCI addressing and some improvements to the
M-mode timer.
This boots linux and passes make check for me.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAl5do3gTHHBhbG1lckBk
YWJiZWx0LmNvbQAKCRAuExnzX7sYiXhlD/9gtiGUT9QxnwygSAck2rLYJHN0rWLC
7FRUar9egPDQ9rtwYKYM5H9fqFzfAxoWc2CTGPPxm75fS49gmEU06p6jBM3gdnNf
WGXPdwefeBhWHxuS0LoQodoLybNmB1H+prrZA6LjoQFbp6BHEdOzSeGBvrUvoYuZ
MCX++mA39h3gRvuXQdMYdPec2DdP07cMRirpXUgzlGtQ5WYUK8fNMDYDNkc0vKQc
aDFDnL7KHRgKt74Fs9LnlEUuZg5r8vEsf4h80SWwBxqDLbSUf9Sh/F8K1abxDUEo
tAm/45mPwTXEbFtEGG9f7uHD6ul0GyoTnybCf/1EQgWUtrm6yhw9b69UUdziOW7/
LVFNjuX4zI175PP6pANb9QnPJnr+VRaCaBg+rXeju3OypkFNsQi6EwefkZFnn1Ye
9hteMOKNaiuYY5qcNXqskJ3j/lnoPTzNpsZKbDinyXARr/tslRqZdn1MU8J9FVUS
M+w0qVgrHPHojmFAbzwKQIONExApiKBkhrV+K5tkbxNNnp3tYBqoLXW8HYpu4MWh
PavscLRVdLzzBJ7AQHnSNmJVlgiAz/VwJh/v0KNhfwrQzE0XAxcCyUQ/1NMLTkjY
CGP3jxV3Wnxf6BQObqrUEUKG0UOOwWmGhYe28suVt8ni4c8eDvZ/z6P+yxFj/v9q
cn03WY6J3beQlw==
=5W7J
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-5.0-sf3' into staging
RISC-V Patches for the 5.0 Soft Freeze, Part 3
This pull request is almost entirely an implementation of the draft hypervisor
extension. This extension is still in draft and is expected to have
incompatible changes before being frozen, but we've had good luck managing
other RISC-V draft extensions in QEMU so far.
Additionally, there's a fix to PCI addressing and some improvements to the
M-mode timer.
This boots linux and passes make check for me.
# gpg: Signature made Tue 03 Mar 2020 00:23:20 GMT
# gpg: using RSA key 2B3C3747446843B24A943A7A2E1319F35FBB1889
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmerdabbelt@google.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
# Subkey fingerprint: 2B3C 3747 4468 43B2 4A94 3A7A 2E13 19F3 5FBB 1889
* remotes/palmer/tags/riscv-for-master-5.0-sf3: (38 commits)
hw/riscv: Provide rdtime callback for TCG in CLINT emulation
target/riscv: Emulate TIME CSRs for privileged mode
riscv: virt: Allow PCI address 0
target/riscv: Allow enabling the Hypervisor extension
target/riscv: Add the MSTATUS_MPV_ISSET helper macro
target/riscv: Add support for the 32-bit MSTATUSH CSR
target/riscv: Set htval and mtval2 on execptions
target/riscv: Raise the new execptions when 2nd stage translation fails
target/riscv: Implement second stage MMU
target/riscv: Allow specifying MMU stage
target/riscv: Respect MPRV and SPRV for floating point ops
target/riscv: Mark both sstatus and msstatus_hs as dirty
target/riscv: Disable guest FP support based on virtual status
target/riscv: Only set TB flags with FP status if enabled
target/riscv: Remove the hret instruction
target/riscv: Add hfence instructions
target/riscv: Add Hypervisor trap return support
target/riscv: Add hypvervisor trap support
target/riscv: Generate illegal instruction on WFI when V=1
target/ricsv: Flush the TLB on virtulisation mode changes
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There's no good reason for it to be type int, change it to bool.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200207161948.15972-3-philmd@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This patch extends CLINT emulation to provide rdtime callback for
TCG. This rdtime callback will be called wheneven TIME CSRs are
read in privileged modes.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When testing e1000 with the virt machine, e1000's I/O space cannot
be accessed. Debugging shows that the I/O BAR (BAR1) is correctly
written with address 0 plus I/O enable bit, but QEMU's "info pci"
shows that:
Bus 0, device 1, function 0:
Ethernet controller: PCI device 8086:100e
...
BAR1: I/O at 0xffffffffffffffff [0x003e].
...
It turns out we should set pci_allow_0_address to true to allow 0
PCI address, otherwise pci_bar_address() treats such address as
PCI_BAR_UNMAPPED.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We extend QEMU RISC-V virt machine by adding Goldfish RTC device
to it. This will allow Guest Linux to sync it's local date/time
with Host date/time via RTC device.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The SiFive test device found on virt machine can be used by
generic syscon reboot and poweroff drivers available in Linux
kernel.
This patch updates FDT generation in virt machine so that
Linux kernel can probe and use generic syscon drivers.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeK1CXAAoJEL/70l94x66DXtkIAI6W5wEY0Yme4M9Q5mGc0RV8
uscPLg0wsg88u6xne8ucCiGymvDREym2ii/aVI0Hi5ish84ZMdCrdck9cd+llpMf
+a3slL26AKlOW8WtYSuyAE1RdLFXngeXdwal5KtWPEExJorkDUPTbwhBzQduQK1a
myoHHcbwdd/96v7FvKnfG8jM6KZtHPQQ0i6+6fX4PN44jaULQNjze8GIrRBEwqw5
uCKJFQPBXiVcxKjH5/kzI1vl2hLJbF2ZGVEzX/U8OPZwyGPHIkWquURo8lvUTPfb
ySlNTUTV2CyrN65TBRXQp/mJi44WvME5Jxlf5rNLBaYXPpL0zhmILKn5X5ya4U0=
=TD0Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Register qdev properties as class properties (Marc-André)
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
# gpg: Signature made Fri 24 Jan 2020 20:16:23 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (58 commits)
build-sys: clean up flags included in the linker command line
target/i386: Add the 'model-id' for Skylake -v3 CPU models
qdev: use object_property_help()
qapi/qmp: add ObjectPropertyInfo.default-value
qom: introduce object_property_help()
qom: simplify qmp_device_list_properties()
vl: print default value in object help
qdev: register properties as class properties
qdev: move instance properties to class properties
qdev: rename DeviceClass.props
qdev: set properties with device_class_set_props()
object: return self in object_ref()
object: release all props
object: add object_class_property_add_link()
object: express const link with link property
object: add direct link flag
object: rename link "child" to "target"
object: check strong flag with &
object: do not free class properties
object: add object_property_set_default
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a minor memory leak in riscv_sifive_u_soc_realize()
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The Chardev events are listed in the QEMUChrEvent enum.
By using the enum in the IOEventHandler typedef we:
- make the IOEventHandler type more explicit (this handler
process out-of-band information, while the IOReadHandler
is in-band),
- help static code analyzers.
This patch was produced with the following spatch script:
@match@
expression backend, opaque, context, set_open;
identifier fd_can_read, fd_read, fd_event, be_change;
@@
qemu_chr_fe_set_handlers(backend, fd_can_read, fd_read, fd_event,
be_change, opaque, context, set_open);
@depends on match@
identifier opaque, event;
identifier match.fd_event;
@@
static
-void fd_event(void *opaque, int event)
+void fd_event(void *opaque, QEMUChrEvent event)
{
...
}
Then the typedef was modified manually in
include/chardev/char-fe.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191218172009.8868-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_kernel() which provides the possibility to access the symbol
table during kernel loading.
The pointer is ignored, if supplied with Image or uImage file.
The Spike board requires the access to locate the HTIF symbols.
Fixes: 0ac24d56c5 ("hw/riscv: Split out the boot functions")
Buglink: https://bugs.launchpad.net/qemu/+bug/1835827
Signed-off-by: Siwei Zhuang <siwei.zhuang@data61.csiro.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The test finisher implements the reset command, which means it's a
"sifive,test1" device. This is a backwards compatible change, so it's
also a "sifive,test0" device. I copied the odd idiom for adding a
two-string compatible field from the ARM virt board.
Fixes: 9a2551ed6f ("riscv: sifive_test: Add reset functionality")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Coreboot developers have requested that they have at least 32MB of flash
to load binaries. We currently have 32MB of flash, but it is split in
two to allow loading two flash binaries. Let's increase the flash size
from 32MB to 64MB to ensure we have a single region that is 32MB.
No QEMU release has include flash in the RISC-V virt machine, so this
isn't a breaking change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Coverity (CID 1405786) thinks that there is a possible memory leak as
we don't guarantee that the memory allocated from riscv_find_firmware()
is freed. This is a false positive, but let's tidy up the code to fix
the warning.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
If the user supplied pflash to QEMU then change the reset code to jump
to the pflash base address instead of the DRAM base address.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add the CFI01 PFlash to the RISC-V virt board. This is the same PFlash
from the ARM Virt board and the implementation is based on the ARM Virt
board. This allows users to specify flash files from the command line.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to use the machine object to create
RISCVVirtState. This is required to add children and aliases to the
machine.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a property that when set to true QEMU will jump from the ROM code to
the start of flash memory instead of DRAM which is the default
behaviour.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to specify machine properties.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The HiFive Unleashed uses is25wp256 SPI NOR flash. There is currently no
model of this in QEMU, so to allow boot firmware developers to use QEMU
to target the Unleashed let's add a chunk of memory to represent the QSPI0
memory mapped flash. This can be targeted using QEMU's -device loader
command line option.
In the future we can look at adding a model for the is25wp256 flash.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On reset only a single L2 cache way is enabled, the others are exposed
as memory that can be used by early boot firmware. This L2 region is
generally disabled using the WayEnable register at a later stage in the
boot process. To allow firmware to target QEMU and the HiFive Unleashed
let's add the L2 LIM (LooselyIntegrated Memory).
Ideally we would want to adjust the size of this chunk of memory as the
L2 Cache Controller WayEnable register is incremented. Unfortunately I
don't see a nice way to handle reducing or blocking out the L2 LIM while
still allowing it be re returned to all enabled from a reset.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
U-Boot expects this alias to be in place in order to fix up the mac
address of the ethernet node.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133033/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The "clock-frequency" property of cpu nodes isn't required. Drop it.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133031/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates model and compatible strings to use the same strings
as used in the Linux kernel device tree (hifive-unleashed-a00.dts).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In the past we did not have a model for PRCI, hence two handcrafted
clock nodes ("/soc/ethclk" and "/soc/uartclk") were created for the
purpose of supplying hard-coded clock frequencies. But now since we
have added the PRCI support in QEMU, we don't need them any more.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds an OTP memory with a given serial number to the sifive_u
machine. With such support, the upstream U-Boot for sifive_fu540
boots out of the box on the sifive_u machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This implements a simple model for SiFive FU540 OTP (One-Time
Programmable) Memory interface, primarily for reading out the
stored serial number from the first 1 KiB of the 16 KiB OTP
memory reserved by SiFive for internal use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating
chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will
use this information to locate the serial node and probe its driver.
However currently we generate the UART node name as "/soc/uart@...",
causing U-Boot fail to find the serial node in DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates the UART base address and IRQs to match the hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Now that we have added a PRCI node, update existing UART and ethernet
nodes to reference PRCI as their clock sources, to keep in sync with
the Linux kernel device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add PRCI mmio base address and size mappings to sifive_u machine,
and generate the corresponding device tree node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
To keep in sync with Linux kernel device tree, generate hfclk and
rtcclk nodes in the device tree, to be referenced by PRCI node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a simple PRCI model for FU540 (sifive_u). It has different
register layout from the existing PRCI model for FE310 (sifive_e).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
With heterogeneous harts config, the PLIC hart topology configuration
string are "M,MS,.." because of the monitor hart #0.
Suggested-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54
RISC-V cores. Currently the sifive_u machine only populates 4 U54
cores. Update the max cpu number to 5 to reflect the real hardware,
by creating 2 CPU clusters as containers for RISC-V hart arrays to
populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It is not useful if we only have one management CPU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[Palmer: Set default CPUs to 2]
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present each hart's hartid in a RISC-V hart array is assigned
the same value of its index in the hart array. But for a system
that has multiple hart arrays, this is not the case any more.
Add a new "hartid-base" property so that hartid number can be
assigned based on the property value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently riscv_harts_realize() creates all harts based on the
same cpu type given in the hart array property. With current
implementation it can only create homogeneous harts. Exact the
hart realize to a separate routine in preparation for supporting
multiple hart arrays.
Note the file header says the RISC-V hart array holds the state
of a heterogeneous array of RISC-V harts, which is not true.
Update the comment to mention homogeneous array of RISC-V harts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use create_unimplemented_device() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently the PRCI register block size is set to 0x8000, but in fact
0x1000 is enough, which is also what the manual says.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For hfxosccfg register programming, SIFIVE_E_PRCI_HFXOSCCFG_RDY and
SIFIVE_E_PRCI_HFXOSCCFG_EN should be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Current SiFive PRCI model only works with sifive_e machine, as it
only emulates registers or PRCI block in the FE310 SoC.
Rename the file name to make it clear that it is for sifive_e.
This also prefix "sifive_e"/"SIFIVE_E" for all macros, variables
and functions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
sifive_u machine does not use PRCI as of today. Remove the prci
header inclusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The inclusion of "target/riscv/cpu.h" is unnecessary in various
sifive model drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Replace the call to hw_error() with qemu_log_mask(LOG_GUEST_ERROR,...)
in various sifive models.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
There is no need to return fdt at the end of create_fdt() because
it's already saved in s->fdt.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This removes "reg-names" and "riscv,max-priority" properties of the
PLIC node from device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Some of the properties only have 1 cell so we should use
qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
"linux,phandle" property is optional. Remove all instances in the
sifive_u, virt and spike machine device trees.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Commit a27bd6c779 ("Include hw/qdev-properties.h less") wrongly
added "hw/hw.h" to sifive_prci.c and sifive_test.c.
Another inclusion of "hw/hw.h" was later added via
commit 650d103d3e ("Include hw/hw.h exactly where needed"), that
resulted in duplicated inclusion of "hw/hw.h".
Fixes: a27bd6c779 ("Include hw/qdev-properties.h less")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
