Given that now we have nvme-subsys device supported, we can manage
namespace allocated, but not attached: detached. This patch introduced
a parameter for nvme-ns device named 'detached'. This parameter
indicates whether the given namespace device is detached from
a entire NVMe subsystem('subsys' given case, shared namespace) or a
controller('bus' given case, private namespace).
- Allocated namespace
1) Shared ns in the subsystem 'subsys0':
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,subsys=subsys0,detached=true
2) Private ns for the controller 'nvme0' of the subsystem 'subsys0':
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,bus=nvme0,detached=true
3) (Invalid case) Controller 'nvme0' has no subsystem to manage ns:
-device nvme,serial=foo,id=nvme0
-device nvme-ns,id=ns1,drive=blknvme0,nsid=1,bus=nvme0,detached=true
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The nvme_dma function doesn't just do DMA (QEMUSGList-based) memory transfers;
it also handles QEMUIOVector copies.
Introduce the NvmeTxDirection enum and rename to nvme_tx. Remove mapping
of PRPs/SGLs from nvme_tx and instead assert that they have been mapped
previously. This allows more fine-grained use in subsequent patches.
Add new (better named) helpers, nvme_{c2h,h2c}, that does both PRP/SGL
mapping and transfer.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The PRP and SGL mapping functions does not have any particular need for
the entire NvmeRequest as a parameter. Clean it up.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Introduce NvmeSg and try to deal with that pesky qsg/iov duality that
haunts all the memory-related functions.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
A Write Zeroes commands should not be counted in either the 'Data Units
Written' or in 'Host Write Commands' SMART/Health Information Log page.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The 'len' member of the nvme_compare_ctx struct is redundant since the
same information is available in the 'iov' member.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Dataset Management is not subject to MDTS, but exceeded a certain size
per range causes internal looping. Report this limit (DMRSL) in the NVM
command set specific identify controller data structure.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a trace event for the offline zone condition when checking zone
read.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
assert may be compiled to a noop and we could end up returning an
uninitialized status.
Fix this by always returning Internal Device Error as a fallback.
Note that, as pointed out by Philippe, per commit 262a69f428 ("osdep.h:
Prohibit disabling assert() in supported builds") this shouldn't be
possible. But clean it up so we don't worry about it again.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: split commit]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add a trace event for the Identify command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Remove an unnecessary le_to_cpu conversion in Identify.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
ZASL (Zone Append Size Limit) is defined exactly like MDTS (Maximum Data
Transfer Size), that is, it is a value in units of the minimum memory
page size (CAP.MPSMIN) and is reported as a power of two.
The 'mdts' nvme device parameter is specified as in the spec, but the
'zoned.append_size_limit' parameter is specified in bytes. This is
suboptimal for a number of reasons:
1. It is just plain confusing wrt. the definition of mdts.
2. There is a lot of complexity involved in validating the value; it
must be a power of two, it should be larger than 4k, if it is zero
we set it internally to mdts, but still report it as zero.
3. While "hw/block/nvme: improve invalid zasl value reporting"
slightly improved the handling of the parameter, the validation is
still wrong; it does not depend on CC.MPS, it depends on
CAP.MPSMIN. And we are not even checking that it is actually less
than or equal to MDTS, which is kinda the *one* condition it must
satisfy.
Fix this by defining zasl exactly like mdts and checking the one thing
that it must satisfy (that it is less than or equal to mdts). Also,
change the default value from 128KiB to 0 (aka, whatever mdts is).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 6eb7a07129 ("hw/block/nvme: change controller pci id") changed
the controller to use a Red Hat assigned PCI Device and Vendor ID, but
did not change the IEEE OUI away from the Intel IEEE OUI.
Fix that and use the locally assigned QEMU IEEE OUI instead if the
`use-intel-id` parameter is not explicitly set. Also reverse the Intel
IEEE OUI bytes.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The Zone Append Size Limit (ZASL) must be at least 4096 bytes, so
improve the user experience by adding an early parameter check in
nvme_check_constraints.
When ZASL is still too small due to the host configuring the device for
an even larger page size, convert the trace point in nvme_start_ctrl to
an NVME_GUEST_ERR such that this is logged by QEMU instead of only
traced.
Reported-by: Corne <info@dantalion.nl>
Cc: Dmitry Fomichev <Dmitry.Fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Firstly, if zoned.max_active is non-zero, zoned.max_open must be less
than or equal to zoned.max_active.
Secondly, if only zones.max_active is set, we have to explicitly set
zones.max_open or we end up with an invalid MAR/MOR configuration. This
is an artifact of the parameters not being zeroes-based like in the
spec.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reported-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and Explicitly Open zones can be closed by Close Zone
management function. This got broken by a recent commit ("hw/block/nvme:
refactor zone resource management") and now such commands fail with
Invalid Zone State Transition status.
Modify nvm_zrm_close() function to make Close Zone work correctly.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for TP 4065a ("Simple Copy Command"), v2020.05.04
("Ratified").
The implementation uses a bounce buffer to first read in the source
logical blocks, then issue a write of that bounce buffer. The default
maximum number of source logical blocks is 128, translating to 512 KiB
for 4k logical blocks which aligns with the default value of MDTS.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
In preparation for Simple Copy, pull write pointer advancement into a
separate function that is independent off an NvmeRequest.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Zone transition handling and resource management is open coded (and
semi-duplicated in the case of open, close and finish).
In preparation for Simple Copy command support (which also needs to open
zones for writing), consolidate into a set of 'nvme_zrm' functions and
in the process fix a bug with the controller not closing an open zone to
allow another zone to be explicitly opened.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Remove the unused NvmeCtrl parameter in nvme_check_zone_write.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
nvme-ns device is registered to a nvme controller device during the
initialization in nvme_register_namespace() in case that 'bus' property
is given which means it's mapped to a single controller.
This patch introduced a new property 'subsys' just like the controller
device instance did to map a namespace to a NVMe subsystem.
If 'subsys' property is given to the nvme-ns device, it will belong to
the specified subsystem and will be attached to all controllers in that
subsystem by enabling shared namespace capability in NMIC(Namespace
Multi-path I/O and Namespace Capabilities) in Identify Namespace.
Usage:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
-device nvme,serial=bar,id=nvme1,subsys=subsys0
-device nvme,serial=baz,id=nvme2,subsys=subsys0
-device nvme-ns,id=ns1,drive=<drv>,nsid=1,subsys=subsys0 # Shared
-device nvme-ns,id=ns2,drive=<drv>,nsid=2,bus=nvme2 # Non-shared
In the above example, 'ns1' will be shared to 'nvme0' and 'nvme1' in
the same subsystem. On the other hand, 'ns2' will be attached to the
'nvme2' only as a private namespace in that subsystem.
All the namespace with 'subsys' parameter will attach all controllers in
the subsystem to the namespace by default.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
We have nvme-subsys and nvme devices mapped together. To support
multi-controller scheme to this setup, controller identifier(id) has to
be managed. Earlier, cntlid(controller id) used to be always 0 because
we didn't have any subsystem scheme that controller id matters.
This patch introduced 'cntlid' attribute to the nvme controller
instance(NvmeCtrl) and make it allocated by the nvme-subsys device
mapped to the controller. If nvme-subsys is not given to the
controller, then it will always be 0 as it was.
Added 'ctrls' array in the nvme-subsys instance to manage attached
controllers to the subsystem with a limit(32). This patch didn't take
list for the controllers to make it seamless with nvme-ns device.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme controller(nvme) can be mapped to a NVMe subsystem(nvme-subsys).
This patch maps a controller to a subsystem by adding a parameter
'subsys' to the nvme device.
To map a controller to a subsystem, we need to put nvme-subsys first and
then maps the subsystem to the controller:
-device nvme-subsys,id=subsys0
-device nvme,serial=foo,id=nvme0,subsys=subsys0
If 'subsys' property is not given to the nvme controller, then subsystem
NQN will be created with serial (e.g., 'foo' in above example),
Otherwise, it will be based on subsys id (e.g., 'subsys0' in above
example).
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
To support multi-path in QEMU NVMe device model, We need to have NVMe
subsystem hierarchy to map controllers and namespaces to a NVMe
subsystem.
This patch introduced a simple nvme-subsys device model. The subsystem
will be prepared with subsystem NQN with <subsys_id> provided in
nvme-subsys device:
ex) -device nvme-subsys,id=subsys0: nqn.2019-08.org.qemu:subsys0
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
[k.jensen: added 'nqn' device parameter per request]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ZynqMP QSPI supports SPI transfer using DMA mode, but currently this
is unimplemented. When QSPI is programmed to use DMA mode, QEMU will
crash. This is observed when testing VxWorks 7.
This adds a Xilinx CSU DMA model and the implementation is based on
https://github.com/Xilinx/qemu/blob/master/hw/dma/csu_stream_dma.c.
The DST part of the model is verified along with ZynqMP GQSPI model.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
Implement the minor changes required to the SCC block for AN547 images:
* CFG2 and CFG5 exist (like AN524)
* CFG3 is reserved (like AN524)
* CFG0 bit 1 is CPU_WAIT; we don't implement it, but note this
in the TODO comment
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-40-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
We've already broken migration compatibility for all the MPS
boards, so we might as well take advantage of this to simplify
the vmstate for the FPGAIO device by folding the counters
subsection into the main vmstate description.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-38-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-200 and SSE-300 have different PID register values from the
IoTKit for the sysctl register block. We incorrectly implemented the
SSE-200 with the same PID values as IoTKit. Fix the SSE-200 bug and
report these register values for SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-19-peter.maydell@linaro.org
The sysctl PDCM_PD_*_SENSE registers control various power domains in
the system and allow the guest to configure which conditions keep a
power domain awake and what power state to use when the domain is in
a low power state. QEMU doesn't model power domains, so for us these
registers are dummy reads-as-written implementations.
The SSE-300 has a different power domain setup, so the set of
registers is slightly different:
Offset SSE-200 SSE-300
---------------------------------------------------
0x200 PDCM_PD_SYS_SENSE PDCM_PD_SYS_SENSE
0x204 reserved PDCM_PD_CPU0_SENSE
0x208 reserved reserved
0x20c PDCM_PD_SRAM0_SENSE reserved
0x210 PDCM_PD_SRAM1_SENSE reserved
0x214 PDCM_PD_SRAM2_SENSE PDCM_PD_VMR0_SENSE
0x218 PDCM_PD_SRAM3_SENSE PDCM_PD_VMR1_SENSE
Offsets 0x200 and 0x208 are the same for both, so handled in a
previous commit; here we deal with 0x204, 0x20c, 0x210, 0x214, 0x218.
(We can safely add new lines to the SSE300 vmstate because no board
uses this device in an SSE300 yet.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-18-peter.maydell@linaro.org
The SSE-300 has a new PWRCTRL register at offset 0x1fc (previously
reserved). This register controls accessibility of some registers
in the Power Policy Units (PPUs). Since QEMU doesn't implement
the PPUs, we don't need to implement any real behaviour for this
register, so we just handle the UNLOCK bit which controls whether
writes to the register itself are permitted and otherwise make it
be reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-17-peter.maydell@linaro.org
The SSE-300 has only one CPU and so no INITSVTOR1. It does
have INITSVTOR0, but unlike the SSE-200 this register now
has a LOCK bit which can be set to 1 to prevent any further
writes to the register. Implement these differences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-16-peter.maydell@linaro.org
In the SSE-300 the CPU_WAIT and NMI_ENABLE registers have
moved offsets, so they are now where the SSE-200's WICCTRL
and EWCTRL were. The SSE-300 does not have WICCTLR or EWCTRL
at all, and the old offsets are reserved:
Offset SSE-200 SSE-300
-----------------------------------
0x118 CPUWAIT reserved
0x118 NMI_ENABLE reserved
0x120 WICCTRL CPUWAIT
0x124 EWCTRL NMI_ENABLE
Handle this reshuffle, and the fact that SSE-300 has only
one CPU and so only one active bit in CPUWAIT.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-15-peter.maydell@linaro.org
The SSE-300's iokit-sysctl device is similar to the SSE-200, but
some registers have moved address or have different behaviours.
In this commit we add case statements for the registers where
the SSE-300 and SSE-200 have the same behaviour. Some registers
are the same on all SSE versions and so need no code change at all.
Putting both of these categories together covers:
0x0 SECDBGSTAT
0x4 SECDBGSET
0x8 SECDBGCLR
0xc SCSECCTRL
0x10 CLK_CFG0 -- this is like SSE-200 FCLK_DIV but with a
different set of clocks being controlled; our implementation
is a dummy reads-as-written anyway
0x14 CLK_CFG1 -- similar to SSE-200 SYSCLK_DIV; our implementation
is a dummy
0x18 CLK_FORCE -- similar to SSE-200 but different bit allocations;
we have a dummy implementation
0x100 RESET_SYNDROME -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x104 RESET_MASK -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x108 SWRESET
0x10c GRETREG
0x200 PDCM_PD_SYS_SENSE -- some bit allocations differ, but our
implementation is a dummy
We also need to migrate the state of these registers which are shared
between the SSE-200 and SSE-300, so update the vmstate 'needed'
function to do this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-14-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
Remove the is_sse200 flag in favour of just directly testing the new
sse_version field.
Since some of these registers exist in the SSE-300 but some do not or
have different behaviour, we expand out the if() statements in the
read and write functions into switch()es, so we have an easy place to
put SSE-300 specific behaviour.
(Until we do add the SSE-300 behaviour, the thing preventing us
reaching the "unreachable" default cases is that armsse.c doesn't
yet pass us an ARMSSE_SSE300 version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-7-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Use the new clock_ns_to_ticks() function in npcm7xx_timer where
appropriate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-5-peter.maydell@linaro.org
Add a new callback event type ClockPreUpdate, which is called on
period changes before the period is updated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-3-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Treat the num_queues field as virtio-endian. On big-endian hosts the
vhost-user-blk num_queues field was in the wrong endianness.
Move the blkcfg.num_queues store operation from realize to
vhost_user_blk_update_config() so feature negotiation has finished and
we know the endianness of the device. VIRTIO 1.0 devices are
little-endian, but in case someone wants to use legacy VIRTIO we support
all endianness cases.
Cc: qemu-stable@nongnu.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210223144653.811468-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
-----BEGIN PGP SIGNATURE-----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=nphT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210308' into staging
target-arm queue:
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
# gpg: Signature made Mon 08 Mar 2021 11:56:24 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210308: (49 commits)
hw/arm/mps2: Update old infocenter.arm.com URLs
docs/system/arm/mps2.rst: Document the new mps3-an524 board
hw/arm/mps2-tz: Provide PL031 RTC on mps3-an524
hw/arm/mps2-tz: Stub out USB controller for mps3-an524
hw/arm/mps2-tz: Add new mps3-an524 board
hw/arm/mps2-tz: Get armv7m_load_kernel() size argument from RAMInfo
hw/arm/mps2-tz: Support ROMs as well as RAMs
hw/arm/mps2-tz: Set MachineClass default_ram info from RAMInfo data
hw/arm/mps2-tz: Make RAM arrangement board-specific
hw/arm/mps2-tz: Allow boards to have different PPCInfo data
hw/arm/mps2-tz: Size the uart-irq-orgate based on the number of UARTs
hw/arm/mps2-tz: Move device IRQ info to data structures
hw/arm/mps2-tz: Allow PPCPortInfo structures to specify device interrupts
hw/arm/mps2-tz: Correct wrong interrupt numbers for DMA and SPI
hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524
hw/arm/mps2-tz: Make number of IRQs board-specific
hw/arm/mps2-tz: Condition IRQ splitting on number of CPUs, not board type
hw/arm/mps2-tz: Make FPGAIO switch and LED config per-board
hw/misc/mps2-fpgaio: Support SWITCH register
hw/misc/mps2-fpgaio: Make number of LEDs configurable by board
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
When the MacOS toolbox ROM transfers data from a target device to an unaligned
memory address, the first/last byte of a 16-bit transfer needs to be handled
separately. This means that the first byte is preloaded into the FIFO before
the transfer, or the last byte remains in the FIFO after the transfer.
The result of this is that the PDMA routines must be updated so that the FIFO
is loaded/unloaded if the last 16-bit word is used (rather than the last byte)
and any remaining byte from a FIFO wraparound is handled correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-43-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM uses non-DMA TI commands to handle the first/last byte
of an unaligned 16-bit transfer to memory.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-42-mark.cave-ayland@ilande.co.uk>
The bottom 5 bits contain the number of bytes remaining in the FIFO which is
trivial to implement with Fifo8 (the remaining bits are unimplemented and left
as 0 for now).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-41-mark.cave-ayland@ilande.co.uk>
Rename ESP_CMDBUF_SZ to ESP_CMDFIFO_SZ and cmdbuf_cdb_offset to cmdfifo_cdb_offset
to indicate that the command buffer type has changed from an array to a Fifo8.
This also enables us to remove the ESPState field cmdlen since the command length
is now simply the number of elements used in cmdfifo.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-40-mark.cave-ayland@ilande.co.uk>
Rename TI_BUFSZ to ESP_FIFO_SZ since this constant is really describing the size
of the FIFO and is not directly related to the TI size.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-39-mark.cave-ayland@ilande.co.uk>
The SCSI bus should remain in the message out phase after the SATN and stop
command rather than transitioning to the command phase. A new ESPState variable
cmdbuf_cdb_offset is added which stores the offset of the CDB from the start
of cmdbuf when accumulating extended message out phase data.
Currently any extended message out data is discarded in do_cmd() before the CDB
is processed in do_busid_cmd().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-38-mark.cave-ayland@ilande.co.uk>
Some guests use a mixture of DMA and non-DMA transfers in combination with the
SATN and stop command to transfer message out phase and command phase bytes to
the target. Prepare for the next commit by adding a maxlen parameter to
get_cmd() to allow partial transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-37-mark.cave-ayland@ilande.co.uk>
This matches the description in the datasheet and is required as support for
non-DMA transfers is added.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-36-mark.cave-ayland@ilande.co.uk>
Commit ea84a44250 "scsi: esp: Defer command completion until previous interrupts
have been handled" provided a mechanism to delay the command completion interrupt
until ESP_RINTR is read after the command has completed.
With the previous fixes for latching the ESP_RINTR bits and deferring the setting
of the command completion interrupt for incoming data to the SCSI callback, this
workaround is no longer required and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-35-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM issues a command to the ESP controller as part of its
"FAST" SCSI routines and then proceeds to read the incoming data soon after
receiving the command completion interrupt.
Unfortunately due to SCSI block transfers being asynchronous the incoming data
may not yet be present causing an underflow error. Resolve this by waiting for
the SCSI subsystem transfer_data callback before raising the command completion
interrupt.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-34-mark.cave-ayland@ilande.co.uk>
Currently the ESP_RINTR register is set to a specific value as required within
the ESP state machine. In order to implement the upcoming deferred interrupt
functionality it is necessary to set individual bits within ESP_RINTR so that
a deferred interrupt will not overwrite the value of any other interrupt bits.
This also requires fixing up a few locations where the ESP_RINTR and ESP_RSEQ
registers are set/reset unexpectedly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-33-mark.cave-ayland@ilande.co.uk>
At this point it is now possible to properly implement the FIFO flush command
without causing guest errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-32-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM performs 4 byte reads/writes when transferring data to
and from the target. Since the SCSI bus is 16-bits wide, use the memory API
to split a 4 byte access into 2 x 2 byte accesses.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-31-mark.cave-ayland@ilande.co.uk>
Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
PDMA as implemented on the Quadra 800 uses DREQ to load data into the FIFO
up to a maximum of 16 bytes at a time. The MacOS toolbox ROM requires this
because it mixes FIFO and PDMA transfers whilst checking the FIFO status
and counter registers to ensure success.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-29-mark.cave-ayland@ilande.co.uk>
Currently the target selection for PDMA is done after the SCSI command has been
delivered which is not correct. Perform target selection as part of the initial
get_cmd() call when the command is submitted: if no target is present, don't
raise DRQ.
If the target is present then switch to the command phase since the MacOS toolbox
ROM checks for this before attempting to submit the SCSI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-28-mark.cave-ayland@ilande.co.uk>
This better describes the purpose of the function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-27-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Here the updates to async_len and ti_size are moved into the corresponding
esp_pdma_read()/esp_pdma_write() function to eliminate the reference to
pdma_cur in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-23-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf and buflen
parameters from get_cmd() since these always reference cmdbuf and ESP_CMDBUF_SZ
respectively.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-21-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf parameter
from do_cmd() since this always points to cmdbuf.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-20-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
This file is borrowed from the RTEMS source code, which comes
with a GPL-2.0-or-later license with a header exception.
Expand the GPL-2.0-or-later license in place to not be dependent
on a 3rd party website. This also fix the misleading comment "The
license and distribution terms for this file may be found in the
file LICENSE in this distribution" referring to the RTEMS distribution
and not to the QEMU one.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210222185605.2714192-1-f4bug@amsat.org>
As replaced the generic CONFIG_SH4 by more fine-grained
selectors, we can remove this now unused config variable.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-9-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_PCI selector for the SH4 PCI controller.
Move the file with the other PCI host devices in hw/pci-host
and add its missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-8-f4bug@amsat.org>
Add more fine-grained selection by adding a CONFIG_TC58128
selector for the TC58128 eeprom.
As this device is only used by the Shix machine, add an entry
to the proper section in MAINTAINERS.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-7-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_TIMER selector for the SH4 timer control unit.
Add the missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-6-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_SCI selector for the SH4 serial controller.
Add the missing MAINTAINERS entries.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-5-f4bug@amsat.org>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_INTC selector for the SH4 interrupt controller.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-4-f4bug@amsat.org>
r2d_init() calls sh7750_init() so depends on SH7750.Harmless
at the moment because nothing actually uses CONFIG_SH7750
(hw/sh4/meson.build always compiles sh7750.c and sh7750_regnames.c
unconditionally).
Fixes: 7ab58d4c84 ("sh4-softmmu.mak: express dependencies with Kconfig")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-3-f4bug@amsat.org>
This code was introduced in commit 27c7ca7e77,
("SHIX board emulation (Samuel Tardieu)"). Use
the same license.
Cc: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-2-f4bug@amsat.org>
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
The AN505 and AN521 don't have any read-only memory, but the AN524
does; add a flag to ROMInfo to mark a region as ROM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-19-peter.maydell@linaro.org
Instead of hardcoding the MachineClass default_ram_size and
default_ram_id fields, set them on class creation by finding the
entry in the RAMInfo array which is marked as being the QEMU system
RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-18-peter.maydell@linaro.org
The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
The AN524 has a different SYSCLK frequency from the AN505 and AN521;
make the SYSCLK frequency a field in the MPS2TZMachineClass rather
than a compile-time constant so we can support the AN524.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-2-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel, RGB. The TCX code already
assumes 32bpp, but it still has some checks of is_surface_bgr()
in an attempt to support 32bpp BGR. is_surface_bgr() will always
return false for the qemu_console_surface(), unless the display
device itself has deliberately created an alternate-format
surface via a function like qemu_create_displaysurface_from().
Drop the never-used BGR-handling code, and assert that we have
a 32-bit surface rather than just doing nothing if it isn't.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215102149.20513-1-peter.maydell@linaro.org
The macro draw_line_func is used only once; just expand it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-10-peter.maydell@linaro.org
We only include the template header once, so just inline it into the
source file for the device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-9-peter.maydell@linaro.org
Fix some minor coding style issues in the template header,
so checkpatch doesn't complain when we move the code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-8-peter.maydell@linaro.org
The draw_line16_32() function in the omap_lcdc template header
includes an ifdef for the case where HOST_WORDS_BIGENDIAN matches
TARGET_WORDS_BIGENDIAN. This is trying to optimise for "source
bitmap and destination bitmap format match", but it is broken,
because in this function the formats don't match: the source is
16-bit colour and the destination is 32-bit colour, so a memcpy()
will produce corrupted graphics output. Drop the bogus ifdef.
This bug was introduced in commit ea644cf343, when we dropped
support for DEPTH values other than 32 from the template header.
The old #if line was
#if DEPTH == 16 && defined(HOST_WORDS_BIGENDIAN) == defined(TARGET_WORDS_BIGENDIAN)
and this was mistakenly changed to
#if defined(HOST_WORDS_BIGENDIAN) == defined(TARGET_WORDS_BIGENDIAN)
rather than deleting the #if as now having an always-false condition.
Fixes: ea644cf343
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-7-peter.maydell@linaro.org
The omap_lcdc template header is already only included once, for
DEPTH==32, but it still has all the macro-driven parameterization
for other depths. Expand out all the macros in the header.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-6-peter.maydell@linaro.org
The function tc6393xb_draw_graphic32() is called in exactly one place,
so just inline the function body at its callsite. This allows us to
drop the template header entirely.
The code move includes a single added space after 'for' to fix
the coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210215103215.4944-5-peter.maydell@linaro.org
Now the template header is included only for BITS==32, expand
out all the macros that depended on the BITS setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-4-peter.maydell@linaro.org
Some SCSI drivers like virtio have an internal mapping for the
host_status. This patch moves the host_status translation into
the SCSI drivers to allow those drivers to set up the correct
values.
Signed-off-by: Hannes Reinecke <hare@suse.de>.
[Added default handling to avoid touching all drivers. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently sg_io_sense_from_errno() converts the two input parameters
'errno' and 'io_hdr' into sense code and SCSI status. Having
split the function off into scsi_sense_from_errno() and
scsi_sense_from_host_status(), both of which are available generically,
we now inline the logic in the callers so that scsi-disk and
scsi-generic will be able to pass host_status to the HBA.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-7-hare@suse.de>
[Put together from "scsi-disk: Add sg_io callback to evaluate status"
and what remains of "scsi: split sg_io_sense_from_errno() in two functions",
with many other fixes. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a READ CAPACITY command would fail, for example s->qdev.blocksize would be
set to zero and cause a division by zero on the next use.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When loading the PVH start address from a 32 bit ELF note, extract
only the appropriate number of bytes.
Fixes: ab969087da ("pvh: Boot uncompressed kernel using direct boot ABI")
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210302090315.3031492-3-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PCI_DEVICE has overwritten DeviceState::unrealize (pci_qdev_unrealize).
However, LSI53C895A, which is a subclass of PCI_DEVICE, overwrites it
again and doesn't save the parent's implementation so the PCI_DEVICE's
implementation of DeviceState::unrealize will never be called when
unrealize a LSI53C895A device. And it will lead to memory leak and
unplug failure.
For a PCI device, it's better to implement PCIDevice::exit instead of
DeviceState::unrealize. So let's change to use PCIDevice::exit.
Fixes: a8632434c7 ("lsi: implement I/O memory space for Memory Move instructions")
Cc: qemu-stable@nongnu.org
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Message-Id: <20210302133016.1221081-1-liangpeng10@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The userspace local APIC is basically untested and does not support many
features such as TSC deadline timer, x2APIC or PV spinlocks. On the
other hand, the PIT and IOAPIC are okay as they are not tied to
the processor and are tested with -M kernel-irqchip=split.
Therefore, deprecate the local APIC and, with it, limit
-M kernel-irqchip=off to the ISA PC machine type, which does not
have a local APIC at all.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the tc6393xb display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-3-peter.maydell@linaro.org
For a long time now the UI layer has guaranteed that the console
surface is always 32 bits per pixel RGB. Remove the legacy dead
code from the milkymist display device which was handling the
possibility that the console surface was some other format.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215103215.4944-2-peter.maydell@linaro.org
At the moment the following QEMU command line triggers an assertion
failure On xlnx-versal SOC:
qemu-system-aarch64 \
-machine xlnx-versal-virt -nographic -smp 2 -m 128 \
-fsdev local,id=shareid,path=${HOME}/work,security_model=none \
-device virtio-9p-device,fsdev=shareid,mount_tag=share \
-fsdev local,id=shareid1,path=${HOME}/Music,security_model=none \
-device virtio-9p-device,fsdev=shareid1,mount_tag=share1
qemu-system-aarch64: ../migration/savevm.c:860:
vmstate_register_with_alias_id:
Assertion `!se->compat || se->instance_id == 0' failed.
This problem was fixed on arm virt platform in commit f58b39d2d5
("virtio-mmio: format transport base address in BusClass.get_dev_path")
It works perfectly on arm virt platform. but there is still there on
xlnx-versal SOC.
The main difference between arm virt and xlnx-versal is they use
different way to create virtio-mmio qdev. on arm virt, it calls
sysbus_create_simple("virtio-mmio", base, pic[irq]); which will call
sysbus_mmio_map internally and assign base address to subsys device
mmio correctly. but xlnx-versal's implements won't do this.
However, xlnx-versal can't switch to sysbus_create_simple() to create
virtio-mmio device. It's because xlnx-versal's cpu use
VersalVirt.soc.fpd.apu.mr as it's memory. which is subregion of
system_memory. sysbus_create_simple will add virtio to system_memory,
which can't be accessed by cpu.
Besides, xlnx-versal can't add sysbus_mmio_map api call too, because
this will add memory region to system_memory, and it can't be added
to VersalVirt.soc.fpd.apu.mr again.
We can solve this by assign correct base address offset on dev_path.
This path was test on aarch64 virt & xlnx-versal platform.
Signed-off-by: schspa <schspa@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STATUS register will be reset to IDLE in
cnpcm7xx_smbus_enter_reset(), no need to preset
it in instance_init().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210228224813.312532-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We hint the 'has_rpu' property is no longer required since commit
6908ec448b ("xlnx-zynqmp: Properly support the smp command line
option") which was released in QEMU v2.11.0.
Beside, this device is marked 'user_creatable = false', so the
only thing that could be setting the property is the board code
that creates the device.
Since the property is not user-facing, we can remove it without
going through the deprecation process.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144350.1979905-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-3-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-2-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let add 'max' cpu while work goes on adding newer CPU types than
Cortex-A72. This allows us to check SVE etc support.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Acked-by: Leif Lindholm <leif@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210216150122.3830863-3-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
-----BEGIN PGP SIGNATURE-----
iQEyBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBA8k8ACgkQIeENKd+X
cFRRMgf41R7Zn1ZSB9GHL3WgLDTPqpT4FAMpTnYRD7wPdspawl1SsHWBgaLNmJWk
dwSLhvHMM44pOVCQRqdkiRrp5t5fDEm6gdRKyNn5uzWFMn7ibYIjmg7OE+79onbN
VES4yTJwuskD/7JRNcrW6RytKRgzKs2au8NxxgtgXprSF0nM9wCu70z4T9XkLfjQ
cpJUUaUCw628uUic/nObTxMnaiEmq/C0qU9SRRKPYVRp7jceCsHMVRazqOgdM6uf
foNHi/uCNKy6I841+D8Po7h57s51LtT78JDRRVRPfWY+SRQyC5l8Eq3UtRPyg39p
7hhkiAKhG4rs8iCXKvMvTz0S//Cx
=BVLq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210304' into staging
RISC-V PR for 6.0
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
# gpg: Signature made Thu 04 Mar 2021 14:44:31 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210304:
hw/riscv: virt: Map high mmio for PCIe
hw/riscv: virt: Limit RAM size in a 32-bit system
hw/riscv: virt: Drop the 'link_up' parameter of gpex_pcie_init()
hw/riscv: Drop 'struct MemmapEntry'
MAINTAINERS: Add a SiFive machine section
goldfish_rtc: re-arm the alarm after migration
docs/system: riscv: Add documentation for sifive_u machine
docs/system: Add RISC-V documentation
docs/system: Sort targets in alphabetical order
hw/riscv: sifive_u: Change SIFIVE_U_GEM_IRQ to decimal value
hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
hw/riscv: sifive_u: Add QSPI0 controller and connect a flash
hw/ssi: Add SiFive SPI controller support
hw/block: m25p80: Add various ISSI flash information
hw/block: m25p80: Add ISSI SPI flash support
target-riscv: support QMP dump-guest-memory
roms/opensbi: Upgrade from v0.8 to v0.9
hw/misc: sifive_u_otp: Use error_report() when block operation fails
target/riscv: Declare csr_ops[] with a known size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
`link_up` is never used in gpex_pcie_init(). Drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the RISC-V defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210220144807.819-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
After a migration the clock offset is updated, but we also
need to re-arm the alarm if needed.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201220112615.933036-7-laurent@vivier.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the SiFive SPI controller model for the FU540 SoC.
The direct memory-mapped SPI flash mode is unsupported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This updates the flash information table to include various ISSI
flashes that are supported by upstream U-Boot and Linux kernel.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present when blk_pread() / blk_pwrite() fails, a guest error
is logged, but this is not really a guest error. Change to use
error_report() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1611026585-29971-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
A pwrite() call returns the number of bytes written (or -1 on error),
and vfio-ccw compares this number with the size of the region to
determine if an error had occurred or not.
If they are not equal, this is a failure and the errno is used to
determine exactly how things failed. An errno of zero is possible
(though unlikely) in this situation and would be translated to a
successful operation.
If they ARE equal, the ret_code field is read from the region to
determine how to proceed. While the kernel sets the ret_code field
as necessary, the region and thus this field is not "written back"
to the user. So the value can only be what it was initialized to,
which is zero.
So, let's convert an unexpected length with errno of zero to a
return code of -EFAULT, and explicitly set an expected length to
a return code of zero. This will be a little safer and clearer.
Suggested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210303160739.2179378-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The virtio standard specifies that any non-transitional device must
reject commands prior to revision setting (which we do). Devices
that are transitional need to assume revision 0 (legacy) if the
driver sends a non-revision-setting command first in order to
support legacy drivers. We neglected to do the latter.
Fortunately, nearly everything worked as intended anyway; the only
problem was not properly rejecting revision setting after some other
command had been issued. Easy to fix by setting revision to 0 if
we see a non-revision command on a legacy-capable revision-less
device.
Found by code inspection, not observed in the wild.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210216111830.1087847-1-cohuck@redhat.com>
Some CLP response data was accidentally dropped when fixing endianness
issues with the Query PCI Function CLP response. All of these values are
sent as 0s to the guest for emulated devices, so the impact is only
observed on passthrough devices.
Fixes: a4e2fff1b1 ("s390x/pci: fix endianness issues")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <1613681609-9349-1-git-send-email-mjrosato@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Commit 2c44220d05 ("meson: convert hw/arch*"), which migrated the old
Makefile.objs to meson.build accidentally excluded virtio-ccw-9p.c and
thus the virtio-9p-ccw device from the build (and potentially also
included the file virtio-ccw-blk.c twice in the source set). And since
CONFIG_VIRTFS can't be used the way it was used here (see commit
2c9dce0196 ("meson: do not use CONFIG_VIRTFS")), the preconditions have
to be written differently.
Let's fix this!
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 2c44220d05 ("meson: convert hw/arch*")
Reported-by: Jakob Naucke <jakob.naucke@ibm.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210218034059.1096078-1-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In the past, virtio-gpu set NULL as the surface for the secondary
consoles to hide its window. The distinction is now handled in
ui/console and the display backends and virtio-gpu does no longer
have to do that.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20210225101316.83940-3-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The surfaces created with former qemu_create_message_surface
did not display the content from the guest and always contained
simple messages describing the reason.
A display backend may want to hide the window showing such a
surface. This change renames the function to
qemu_create_placeholder_surface, and adds "placeholder" flag; the
display can check the flag to decide to do anything special like
hiding the window.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20210225101316.83940-1-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmA+SYcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpUAAIALa9WkjdxjZhb4FzP1OLBSTEISLEfrPE4Zk/
s5yY1wEDvH83D6fxTHv1B8tISwJ3RJn8ZhsP0c0Mb6stT7D33m7YfMFtNXBEfENX
gMgwdC2QxGMZXKGR+dIpxtYghjvuzAVN+e9w27C+s855JJ8y+chghtLuDJIbqpAk
QopftjiZix2bPYmrxlVw/A7inXL2jseJyYsgGAzIACmsGC70jK4Rk1vxrAF+2n15
D4qKOG3QLJXrfIVa8iDz/ojlVUmLWl8jnoE+oY+rjtckQHJKqodlJi5yeJxGEa3/
G7db+AIzEBge78dq7LBSJOTjoUFoQ+6Hv1QtKk2GcMKdEnsj0ng=
=NGys
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,virtio,pci: bug fixes
Fixes all over the place. Specifically this fixes
a bug which made windows guests lose device config
(such as the configured fixed IP) after upgrading
to the new QEMU.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 02 Mar 2021 14:19:51 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
vhost: simplify vhost_dev_init() fail_busyloop label
hw/pci: Have safer pcie_bus_realize() by checking error path
virtio-net: handle zero mac for a vdpa peer
i386/acpi: restore device paths for pre-5.1 vms
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmA3tzQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMsngf+OkbgTDouxq3qnn1K89n6j2wKlAj0
qPP+57o1sv5u5MjX0BkawXCMJfvTKJaOt/Cs8S0FaPTehfR5H0T2tL76KZBEdlEP
/+V3EC0Qmd1S47LKIOuDkV15szvnccyjpgwaL7Osjb0Eh0SxeXd4pBTc3yYtkacu
zb/srZ63U2iJZr93QwGmEJjuW57WNym6QWXF3Mrg9PFXybkXFTGumB2vZMlQc+MN
RWPTUKZKAiIr/HfdvpIETXY+HzJhylvIQ8OVWtM3XDorl48OWcOat/jyeNEVYgG3
o+gxIRnfvIL+42GkmUFbOKLzT5SV6p9EYYGLTuE1kU7nc6HWoD0CdPxA3A==
=UBVO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging
* fix --enable-fuzzing linker failures (Alexander)
* target/i386: Add bus lock debug exception support (Chenyi)
* update documentation for preferred boolean option syntax (Daniel)
* make SCSI io_timeout configurable (Hannes)
* fix handling of guest recoverable SCSI errors (myself)
* misc fixes (Pavel, Zheng Zhan Liang, Zihao)
* fix installation of binaries with entitlements (Akihiko)
# gpg: Signature made Thu 25 Feb 2021 14:41:56 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini-gitlab/tags/for-upstream: (29 commits)
tcg/i386: rdpmc: fix the the condtions
chardev: do not use short form boolean options in non-QemuOpts character device descriptions
vl: deprecate -writeconfig
target/i386: Add bus lock debug exception support
qom/object.c: Fix typo
target/i386: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -cpu
docs: update to show preferred boolean syntax for -vnc
docs: update to show preferred boolean syntax for -chardev
qemu-options: update to show preferred boolean syntax for -vnc
qemu-options: update to show preferred boolean syntax for -incoming
qemu-options: update to show preferred boolean syntax for -netdev
qemu-options: update to show preferred boolean syntax for -spice
qemu-options: update to show preferred boolean syntax for -chardev
gdbstub: use preferred boolean option syntax
char: don't fail when client is not connected
scsi: drop 'result' argument from command_complete callback
scsi-disk: pass guest recoverable errors through even for rerror=stop
scsi-disk: pass SCSI status to scsi_handle_rw_error
scsi: introduce scsi_sense_from_errno()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Requiring a conditional for every goto is tedious:
if (busyloop_timeout) {
goto fail_busyloop;
} else {
goto fail;
}
Move the conditional to into the fail_busyloop label so that it's safe
to jump to this label unconditionally.
This change makes the migrate_add_blocker() error case more consistent.
It jumped to fail_busyloop unconditionally whereas the memslots limits
error case was conditional.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210222114931.272308-1-stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While pci_bus_realize() currently does not use the Error* argument,
it would be an error to leave pcie_bus_realize() setting bus->flags
if pci_bus_realize() had failed.
Fix by using a local Error* and return early (propagating the error)
if pci_bus_realize() failed.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210201153700.618946-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some mlx vdpa devices with kernels at least up to 5.11 currently present
0 as their MAC address. This is because they have not been
pre-configured with a MAC: they have a learning bridge and only learn
the MAC once guest is up. Kernel patches and tools to allow programming
the MAC from host are being developed. For now - since these
combinations exist in the field - let's detect zero mac and just try to
proceed with the mac from the qemu command line.
This makes the guest use this MAC to send packets in turn teaching
the MAC to the card, and things work.
TODO:
report the actual MAC from QEMU commad line in the info message.
TODO:
detect that a (non-zero) hardware MAC does not match QEMU command line
and fail init.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20210225165506.18321-2-lulu@redhat.com>
mst: rewritten code comments, message printed and the commit log.
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Tested-by: Adrian Moreno <amorenoz@redhat.com>
Tested-by: Sean Mooney <smooney@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After fixing the _UID value for the primary PCI root bridge in
af1b80ae it was discovered that this change updates Windows
configuration in an incompatible way causing network configuration
failure unless DHCP is used. More details provided on the list:
https://lists.gnu.org/archive/html/qemu-devel/2021-02/msg08484.html
This change reverts the _UID update from 1 to 0 for q35 and i440fx
VMs before version 5.2 to maintain the original behaviour when
upgrading.
Cc: qemu-stable@nongnu.org
Cc: qemu-devel@nongnu.org
Reported-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vitaly Cheptsov <cheptsov@ispras.ru>
Message-Id: <20210301195919.9333-1-cheptsov@ispras.ru>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: af1b80ae56 ("i386/acpi: fix inconsistent QEMU/OVMF device paths")
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, recoverable sense values are only passed directly to the
guest only for rerror=report. However, when rerror/werror are 'stop'
we still don't want the host to be involved on every UNIT ATTENTION
(especially considered that the QMP event will not have enough information
to act on the report).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
