but there are very small diffs in register definitions. For that, add
new options SSCOM_S3C{2800,2410,2400} and include appropriate
s3c*reg.h.
SSCOM_S3C2410 is also needed for interrupt controller differences.
The new code maintains two variables 'current_spl_level' and
'hardware_spl_level'. Variable hardware_spl_level reflects actual
priority level at the hardware's point of view. hardware_spl_level is
always synchronized to hardware.
splraise() just increases current_spl_level. splx() sets
current_spl_level. If (and only if) hardware_spl_level and
current_spl_level is not same, splx() synchronizes interrupt mask
register and hardware_spl_level to current_spl_level.
In most case, splraise() raises current_spl_level and splx() restores
only current_spl_level.
When an interrupt occurs, hardware_spl_level and interrupt mask
register are synchronized to current_spl_level.
In this implementation, during a higher priority interrupt handler is
running, lower priority interrupts never cause intr_dispatch() to run.
It will avoid some race condition.
config write with the device number specified in AD[15:11]. If
we don't set this field when issuing a Type 0 cycle, each device
could end of thinking it is at device 0, which can cause a number
of problems. Doing this unconditionally should be OK when only
PCI devices are present.
be inserted into ktrace records. The general change has been to replace
"struct proc *" with "struct lwp *" in various function prototypes, pass
the lwp through and use l_proc to get the process pointer when needed.
Bump the kernel rev up to 1.6V
the test as spl0 is actually a macro for splx(0). The code now calls
splx(0)
(note building with the #ifdef fixed, caused the build to fail on a
GENERIC acorn32 kernel.)
enabled on amd64). Add a dmat64 field to various PCI attach structures,
and pass it down where needed. Implement a simple new function called
pci_dma64_available(pa) to test if 64bit DMA addresses may be used.
This returns 1 iff _PCI_HAVE_DMA64 is defined in <machine/pci_machdep.h>,
and there is more than 4G of memory.
with a more generic "devmap" structure that can also handle mappings
made with large and small pages. Add new pmap routines to enter these
mappings during bootstrap (and "remember" the devmap), and routines to
look up the static mappings once the kernel is running.
child drivers such as interrupt and gpio controllers.
- Add a function to probe SDRAM size at boot time.
- Add a function to configure the Clock Manager's CKEN settings.
- Add an INTC driver.
- Add a GPIO driver.
- Add attach glue for the PXA2x0's "almost" 16550-compatible uarts.
- Tweak the LCD driver to use the GPIO driver's services for setting
up GPIO pin function.
to both the EEPROM *and* the PHY on the Ethernet interface now, at least,
though it is still not completely working.
Many thanks to Stephen Goadhouse at ADI for some hints.
directly. The old code was totally bogus for the new pmap. New code
lifted from SH5 port.
Fixes panics in ffs_balloc_ufs2() seen while stress-testing a file
system on an XScale-based server platform.
IST_EDGE_{FALLING,RISING,BOTH}, or IST_LEVEL_{LOW,HIGH}. This
argument is valid only for GPIO interrupts (IRQ0..7).
+ Don't clear interrupt pending bits for IIC in interrupt handler.
Since clearing these bits starts next IIC transmission immediately,
IIC driver should handle these.
http://mail-index.netbsd.org/source-changes/2003/05/08/0068.html
There were some side-effects that I didn't anticipate, and fixing them
is proving to be more difficult than I thought, do just eject for now.
Maybe one day we can look at this again.
Fixes PR kern/21517.
isa_dmamap_create() calls to their open/close entrypoints. This worked
with some luck, but broke on i386 when _bus_dmamap_create started
to allocate bounce buffers upfront, since memory below 16M may well
not be available when the sound devices is opened for the Nth time.
To fix this, create a new simple interface, isa_drq_alloc/isa_drq_free,
wrappers around already existing bitmask macros. These are expected
to be used before an isa_dmamap_create call, and after an
isa_dmamap_destroy call, respectively. For the sb and ad1848 drivers,
they're deferred until open/close.
All isa_dmamap_create calls can now use BUS_DMA_ALLOCNOW and be done
at attach time.
space is advertised to UVM by making virtual_avail and virtual_end
first-class exported variables by UVM. Machine-dependent code is
responsible for initializing them before main() is called. Anything
that steals KVA must adjust these variables accordingly.
This reduces the number of instances of this info from 3 to 1, and
simplifies the pmap(9) interface by removing the pmap_virtual_space()
function call, and removing two arguments from pmap_steal_memory().
This also eliminates some kludges such as having to burn kernel_map
entries on space used by the kernel and stolen KVA.
This also eliminates use of VM_{MIN,MAX}_KERNEL_ADDRESS from MI code,
this giving MD code greater flexibility over the bounds of the managed
kernel virtual address space if a given port's specific platforms can
vary in this regard (this is especially true of the evb* ports).
Also in the ARM32_PMAP_NEW case, reclaim the USPACE-bytes of wasted space
at the top of the user address that hasn't been needed for a very very
long time.
for L2 allocation. This avoids potential recursive calls into
uvm_km_kmemalloc() via the pool allocator.
Bug spotted by Allen Briggs while trying to boot on a machine with 512MB
of memory.
breakpoint address before it's used. Currently a no-op on all but sh5.
This is useful on sh5, for example, to mask off the instruction
type encoding in the bottom two address bits, and makes it possible
to do "db> break $rXX" instead of manually munging the address.
by the application, all NetBSD interfaces are made visible, even
if some other feature-test macro (like _POSIX_C_SOURCE) is defined.
<sys/featuretest.h> defined _NETBSD_SOURCE if none of _ANSI_SOURCE,
_POSIX_C_SOURCE and _XOPEN_SOURCE is defined, so as to preserve
existing behaviour.
This has two major advantages:
+ Programs that require non-POSIX facilities but define _POSIX_C_SOURCE
can trivially be overruled by putting -D_NETBSD_SOURCE in their CFLAGS.
+ It makes most of the #ifs simpler, in that they're all now ORs of the
various macros, rather than having checks for (!defined(_ANSI_SOURCE) ||
!defined(_POSIX_C_SOURCE) || !defined(_XOPEN_SOURCE)) all over the place.
I've tried not to change the semantics of the headers in any case where
_NETBSD_SOURCE wasn't defined, but there were some places where the
current semantics were clearly mad, and retaining them was harder than
correcting them. In particular, I've mostly normalised things so that
_ANSI_SOURCE gets you the smallest set of stuff, then _POSIX_C_SOURCE,
_XOPEN_SOURCE and _NETBSD_SOURCE in that order.
Tested by building for vax, encouraged by thorpej, and uncontested in
tech-userlevel for a week.
* Define a new "MMU type", ARM_MMU_SA1. While the SA-1's MMU is basically
compatible with the generic, the SA-1 cache does not have a write-through
mode, and it is useful to know have an indication of this.
* Add a new PMAP_NEEDS_PTE_SYNC indicator, and try to evaluate it at
compile time. We evaluate it like so:
- If SA-1-style MMU is the only type configured -> 1
- If SA-1-style MMU is not configured -> 0
- Otherwise, defer to a run-time variable.
If PMAP_NEEDS_PTE_SYNC might evaluate to true (SA-1 only or run-time
check), then we also define PMAP_INCLUDE_PTE_SYNC so that e.g. assembly
code can include the necessary run-time support. PMAP_INCLUDE_PTE_SYNC
largely replaces the ARM32_PMAP_NEEDS_PTE_SYNC manual setting Steve
included with the original new pmap.
* In the new pmap, make pmap_pte_init_generic() check to see if the CPU
has a write-back cache. If so, init the PT cache mode to C=1,B=0 to get
write-through mode. Otherwise, init the PT cache mode to C=1,B=1.
* Add a new pmap_pte_init_arm8(). Old pmap, same as generic. New pmap,
sets page table cacheability to 0 (ARM8 has a write-back cache, but
flushing it is quite expensive).
* In the new pmap, make pmap_pte_init_arm9() reset the PT cache mode to
C=1,B=0, since the write-back check in generic gets it wrong for ARM9,
since we use write-through mode all the time on ARM9 right now. (What
this really tells me is that the test for write-through cache is less
than perfect, but we can fix that later.)
* Add a new pmap_pte_init_sa1(). Old pmap, same as generic. New pmap,
does generic initialization, then resets page table cache mode to
C=1,B=1, since C=1,B=0 does not produce write-through on the SA-1.
was checked in:
* It was not actually disabling the MMU, and so jumping to the
reset vector would happily cause a panic(), since it would be
the kernel's reset vector, not the ROM's.
* In the event the system was using high vectors, VECRELOC was not
getting cleared, which has the potential to wreak havoc when re-entering
the ROM.
* It was totally broken for CPUs < ARMv4; you still need to disable
the MMU on those, just need to skip the ARMv4 TLB flush.
* The code that was checked in would only work if the kernel is mapped
VA==PA. For systems where the kernel is NOT mapped VA==PA, you only
get the prefetch depth # of insns (2) after the MMU is turned off before
you have fix the PC.
Backing out the change fixes rebooting on several evbarm platforms.
requires that the CPU control vector be properly readable. I believe that
all CPUs that have high vector support have a readable CPU control register,
but if we ever encounter one that does not, then we'll have to adjust this
code.
Some features of the new pmap are:
- It allows L1 descriptor tables to be shared efficiently between
multiple processes. A typical "maxusers 32" kernel, where NPROC is set
to 532, requires 35 L1s. A "maxusers 2" kernel runs quite happily
with just 4 L1s. This completely solves the problem of running out
of contiguous physical memory for allocating new L1s at runtime on a
busy system.
- Much improved cache/TLB management "smarts". This change ripples
out to encompass the low-level context switch code, which is also
much smarter about when to flush the cache/TLB, and when not to.
- Faster allocation of L2 page tables and associated metadata thanks,
in part, to the pool_cache enhancements recently contributed to
NetBSD by Wasabi Systems.
- Faster VM space teardown due to accurate referenced tracking of L2
page tables.
- Better/faster cache-alias tracking.
The new pmap is enabled by adding options ARM32_PMAP_NEW to the kernel
config file, and making the necessary changes to the port-specific
initarm() function. Several ports have already been converted and will
be committed shortly.
page: -1 for error, 0 for EOF, 1 otherwise. Inspired by an OpenBSD commit
message, pointed out by Miod Vallat in private mail.
vax/mba/hp.c: check return value <= 0, not < 0 to be concistent with how
other places handle return values from bounds_check_with_label().
to extract the physical address from the virtual.
On the ARM, also use the "read-only at MMU" indication to avoid a
redundant cache clean operation.
Other platforms should use these two as examples of how to use these
new pool/mbuf features to improve network performance. Note this requires
a platform to provide a working POOL_VTOPHYS().
Part 3 in a series of simple patches contributed by Wasabi Systems
to improve network performance.
objects. Clients of the pool_cache API must consistently use
the "paddr" variants or not, otherwise behavior is undefined.
Enable this on Alpha, ARM, MIPS, and x86. Other platforms must
define POOL_VTOPHYS() in the appropriate manner in order to enable
the feature.
Part 1 of a series of simple patches contributed by Wasabi Systems
to improve network performance.
cache based on CPU id. write-through on PXA2[15]0 B2 stepping and
earlier. write-back on C0 and C1 stepping (a.k.a PXA2[15]5 A0)
options XSCALE_CACHE_WRITE_{THROUGH,BACK} can override it.
for other XScale CPUs than PXA2xx, XSCALE_CACHE_WRITE_THROUGH works
same as before.
* The offset format was wrong.
* There is no post-increment or index register update.
* It wasn't even matching because the mask was wrong.
Also touch up ldr/str disassembly slightly.
too many bits (including some reserved ones) and was writing the wrong value
for the TLB flush.
Also, if the flag is off, don't write the control register!
indirect configuration (because the BECC is a soft-core, it could
have a variety of peripherals in the FPGA). Also add support for
local untranslated DMA.
rearnsha