On reset only a single L2 cache way is enabled, the others are exposed
as memory that can be used by early boot firmware. This L2 region is
generally disabled using the WayEnable register at a later stage in the
boot process. To allow firmware to target QEMU and the HiFive Unleashed
let's add the L2 LIM (LooselyIntegrated Memory).
Ideally we would want to adjust the size of this chunk of memory as the
L2 Cache Controller WayEnable register is incremented. Unfortunately I
don't see a nice way to handle reducing or blocking out the L2 LIM while
still allowing it be re returned to all enabled from a reset.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
U-Boot expects this alias to be in place in order to fix up the mac
address of the ethernet node.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133033/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The "clock-frequency" property of cpu nodes isn't required. Drop it.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133031/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates model and compatible strings to use the same strings
as used in the Linux kernel device tree (hifive-unleashed-a00.dts).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In the past we did not have a model for PRCI, hence two handcrafted
clock nodes ("/soc/ethclk" and "/soc/uartclk") were created for the
purpose of supplying hard-coded clock frequencies. But now since we
have added the PRCI support in QEMU, we don't need them any more.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds an OTP memory with a given serial number to the sifive_u
machine. With such support, the upstream U-Boot for sifive_fu540
boots out of the box on the sifive_u machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This implements a simple model for SiFive FU540 OTP (One-Time
Programmable) Memory interface, primarily for reading out the
stored serial number from the first 1 KiB of the 16 KiB OTP
memory reserved by SiFive for internal use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating
chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will
use this information to locate the serial node and probe its driver.
However currently we generate the UART node name as "/soc/uart@...",
causing U-Boot fail to find the serial node in DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates the UART base address and IRQs to match the hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Now that we have added a PRCI node, update existing UART and ethernet
nodes to reference PRCI as their clock sources, to keep in sync with
the Linux kernel device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add PRCI mmio base address and size mappings to sifive_u machine,
and generate the corresponding device tree node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
To keep in sync with Linux kernel device tree, generate hfclk and
rtcclk nodes in the device tree, to be referenced by PRCI node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a simple PRCI model for FU540 (sifive_u). It has different
register layout from the existing PRCI model for FE310 (sifive_e).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
With heterogeneous harts config, the PLIC hart topology configuration
string are "M,MS,.." because of the monitor hart #0.
Suggested-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54
RISC-V cores. Currently the sifive_u machine only populates 4 U54
cores. Update the max cpu number to 5 to reflect the real hardware,
by creating 2 CPU clusters as containers for RISC-V hart arrays to
populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It is not useful if we only have one management CPU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[Palmer: Set default CPUs to 2]
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present each hart's hartid in a RISC-V hart array is assigned
the same value of its index in the hart array. But for a system
that has multiple hart arrays, this is not the case any more.
Add a new "hartid-base" property so that hartid number can be
assigned based on the property value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently riscv_harts_realize() creates all harts based on the
same cpu type given in the hart array property. With current
implementation it can only create homogeneous harts. Exact the
hart realize to a separate routine in preparation for supporting
multiple hart arrays.
Note the file header says the RISC-V hart array holds the state
of a heterogeneous array of RISC-V harts, which is not true.
Update the comment to mention homogeneous array of RISC-V harts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use create_unimplemented_device() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently the PRCI register block size is set to 0x8000, but in fact
0x1000 is enough, which is also what the manual says.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For hfxosccfg register programming, SIFIVE_E_PRCI_HFXOSCCFG_RDY and
SIFIVE_E_PRCI_HFXOSCCFG_EN should be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Current SiFive PRCI model only works with sifive_e machine, as it
only emulates registers or PRCI block in the FE310 SoC.
Rename the file name to make it clear that it is for sifive_e.
This also prefix "sifive_e"/"SIFIVE_E" for all macros, variables
and functions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
sifive_u machine does not use PRCI as of today. Remove the prci
header inclusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The inclusion of "target/riscv/cpu.h" is unnecessary in various
sifive model drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Replace the call to hw_error() with qemu_log_mask(LOG_GUEST_ERROR,...)
in various sifive models.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
There is no need to return fdt at the end of create_fdt() because
it's already saved in s->fdt.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This removes "reg-names" and "riscv,max-priority" properties of the
PLIC node from device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Some of the properties only have 1 cell so we should use
qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
"linux,phandle" property is optional. Remove all instances in the
sifive_u, virt and spike machine device trees.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Commit a27bd6c779 ("Include hw/qdev-properties.h less") wrongly
added "hw/hw.h" to sifive_prci.c and sifive_test.c.
Another inclusion of "hw/hw.h" was later added via
commit 650d103d3e ("Include hw/hw.h exactly where needed"), that
resulted in duplicated inclusion of "hw/hw.h".
Fixes: a27bd6c779 ("Include hw/qdev-properties.h less")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a reset opcode for sifive_test device to trigger a system
reset for testing purpose.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present when "-bios image" is supplied, we just use the straight
path without searching for the configured data directories. Like
"-bios default", we add the same logic so that "-L" actually works.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a helper routine for finding firmware. It is currently
used only for "-bios default" case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The correct property name is clock-names, not clocks-names.
Without this patch, the Ethernet driver fails to instantiate with
the following error.
macb 100900fc.ethernet: failed to get macb_clk (-2)
macb: probe of 100900fc.ethernet failed with error -2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The riscv uart needs valid clocks. This requires a refereence
to the clock node. Since the SOC clock is not emulated by qemu,
add a reference to a fixed clock instead. The clock-frequency
entry in the uart node does not seem to be necessary, so drop it.
In addition to a reference to the clock, the driver also needs
an aliases entry for the serial node. Add it as well.
Without this patch, the serial driver fails to instantiate with
the following error message.
sifive-serial 10013000.uart: unable to find controller clock
sifive-serial: probe of 10013000.uart failed with error -2
when trying to boot Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add support for loading initrd with "-initrd <filename>"
to the sifive_u machine. This lets us boot into Linux without
disk drive.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
hw/boards.h pulls in almost 60 headers. The less we include it into
headers, the better. As a first step, drop superfluous inclusions,
and downgrade some more to what's actually needed. Gets rid of just
one inclusion into a header.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
Fix a typo in the warning message displayed to users, don't print the
message when running inside qtest and don't mention a specific QEMU
version for the deprecation.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
If the user hasn't specified a firmware to load (with -bios) or
specified no bios (with -bios none) then load OpenSBI by default. This
allows users to boot a RISC-V kernel with just -kernel.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The global smp variables in riscv are replaced with smp machine properties.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190518205428.90532-6-like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[ehabkost: fix spike_board_init()]
[ehabkost: fix riscv_sifive_e_soc_init()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Extend the RISC-V kernel loader to support Image and uImage files.
A Linux kernel can now be booted with:
qemu-system-riscv64 -machine virt -bios fw_jump.bin -kernel Image
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add support for loading a firmware file for the virt machine and the
SiFive U. This can be run with the following command:
qemu-system-riscv64 -machine virt -bios fw_jump.bin -kernel vmlinux
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Split the common RISC-V boot functions into a seperate file. This allows
us to share the common code.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the PLIC is instantiated to support only one hart, while
the machine allows at most 4 harts to be created. When more than 1
hart is configured, PLIC needs to instantiated to support multicore,
otherwise an SMP OS does not work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the cpu, plic and ethclk nodes' phandles are hard-coded
to 1/2/3 in DT. If we configure more than 1 cpu for the machine,
all cpu nodes' phandles conflict with each other as they are all 1.
Fix it by removing the hardcode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently, there is no cpu topology defined in RISC-V.
Define a device tree node that clearly describes the
entire topology. This saves the trouble of scanning individual
cache to figure out the topology.
Here is the linux kernel patch series that enables topology
for RISC-V.
http://lists.infradead.org/pipermail/linux-riscv/2019-June/005072.html
CPU topology after applying this patch in QEMU & above series in kernel
/ # cat /sys/devices/system/cpu/cpu2/topology/thread_siblings_list
2
/ # cat /sys/devices/system/cpu/cpu2/topology/physical_package_id
0
/ # cat /sys/devices/system/cpu/cpu2/topology/core_siblings_list
0-7
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Coverity pointed out a memory leak in riscv_sifive_e_soc_realize(),
where a pair of recently added MemoryRegion instances would not be freed
if there were errors elsewhere in the function. The fix here is to
simply not use dynamic allocation for these instances: there's always
one of each in SiFiveESoCState, so instead we just include them within
the struct.
Fixes: 30efbf330a ("SiFive RISC-V GPIO Device")
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The largest pci bus number should be calculated from ECAM size,
instead of its base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Writes to the SiFive PRCI registers are preserved while leaving the
ready bits set for the HFX/HFR oscillators and the lock bit set for the
PLL.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a generic spike machine (not tied to a version) and deprecate the
spike mahines that are tied to a specific version. As we can now specify
the CPU via the command line we no londer need specific versions of the
spike machines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
QEMU model of the GPIO device on the SiFive E300 series SOCs.
The pins are not used by a board definition yet, however this
implementation can already be used to trigger GPIO interrupts from the
software by configuring a pin as both output and input.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using error_report() to print guest errors let's use
qemu_log_mask(LOG_GUEST_ERROR,...) to log the error.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch fixes four different things, to maintain bisectability they
have been merged into a single patch. The following fixes are below:
sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the
past as the priority_base offset has also been set incorrectly. We are
about to fix the priority_base offset so first first the irq
calculation.
sifive_u: Fix PLIC priority base offset and numbering
According to the FU540 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00. The same manual also specifies that the
PLIC only has 53 source priorities. Fix these two incorrect header
files.
We also need to over extend the plic_gpios[] array as the PLIC sources
count from 1 and not 0.
riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00.
riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E
offsets.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The UART0's interrupt vector is wrongly set to 1 in the device tree.
Use SIFIVE_U_UART0_IRQ instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the sifive uart model only generates RX interrupt. This
updates it to generate TX interrupt so that it is more useful.
Note the TX fifo is still unimplemented.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We can't allow the supervisor to control SEIP as this would allow the
supervisor to clear a pending external interrupt which will result in
lost a interrupt in the case a PLIC is attached. The SEIP bit must be
hardware controlled when a PLIC is attached.
This logic was previously hard-coded so SEIP was always masked even
if no PLIC was attached. This patch adds riscv_cpu_claim_interrupts
so that the PLIC can register control of SEIP. In the case of models
without a PLIC (spike), the SEIP bit remains software controlled.
This interface allows for hardware control of supervisor timer and
software interrupts by other interrupt controller models.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The mode variable only uses the lower 4-bits (M,H,S,U) so
replace the GCC specific __builtin_popcount with ctpop8.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set msi_nonbroken as true for the PLIC.
According to the comment located here:
https://git.qemu.org/?p=qemu.git;a=blob;f=hw/pci/msi.c;h=47d2b0f33c664533b8dbd5cb17faa8e6a01afe1f;hb=HEAD#l38
the msi_nonbroken variable should be set to true even if they don't
support MSI. In this case that is what we are doing as we don't support
MSI.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reported-by: Andrea Bolognani <abologna@redhat.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Message-Id: <256afbb2da005dc62c159b0f4a4fc0d95c050660.1552679970.git.alistair.francis@wdc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-enable PCI_DEVICES for RISC-V.
The patch is based on other <arch>/Kconfig.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: 82a230d5a3 ("riscv-softmmu.mak: replace CONFIG_* with Kconfig "select" directives")
Message-Id: <20190311091256.18385-1-david.abdurachmanov@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cast the kernel start address to the target bit length.
This ensures that we calculate the initrd offset to a valid address for
the architecture.
Steps to reproduce the original problem (reported by Alex):
Build U-Boot for the virt machine for riscv32. Then run it with
$ qemu-system-riscv32 -M virt -kernel u-boot -nographic -initrd <a file>
You can find the initrd address with
U-Boot# fdt addr $fdtcontroladdr
U-Boot# fdt ls /chosen
Then take a peek at that address:
U-Boot# md.b <addr>
and you will see that there is nothing there without this patch. The
reason is that the binary was loaded to a negative address.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Reported-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add the new configs to default-configs/riscv*-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-19-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The watermark bits are set in the interrupt pending register according
to the configuration of txcnt and rxcnt in the txctrl and rxctrl
registers.
Since the UART TX does not implement a FIFO, the txwm bit is set as long
as the TX watermark level is greater than zero.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Previously the second UARTs on the sifive_e and sifive_u machines
where disabled due to check-qtest-riscv32 and check-qtest-riscv64
failures. Recent changes in the QEMU core serial code have
resolved these failures so the second UARTs can be instantiated.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The address calculation for the pending bitfield had
a copy paste bug. This bug went unnoticed because the Linux
PLIC driver does not read the pending bitfield, rather it
reads pending interrupt numbers from the claim register
and writes acknowledgements back to the claim register.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Reported-by: Vincent Siles <vincent.siles@ens-lyon.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
A missing shift made updates to the low order bits
of timecmp erroneously copy the old low order bits
into the high order bits of the 64-bit timecmp
register. Add the missing shift and rename timecmp
local variables to timecmp_hi and timecmp_lo.
This bug didn't show up as the low order bits are
usually written first followed by the high order
bits meaning the high order bits contained an invalid
value between the timecmp_lo and timecmp_hi update.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Co-Authored-by: Johannes Haring <johannes.haring@gmx.net>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The 'clock-frequency' DT property is required by U-Boot to compute
the divider value. This patch sets the 'clock-frequency' DT property
of the SiFive UART device tree node (similar to virt machine).
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Connect the gpex PCIe device based on the device tree included in the
HiFive Unleashed ROM.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Coverity caught a malloc() call that was never freed. This patch ensures
that we free the memory but also updates the allocation to use
g_strdup_printf() instead of malloc().
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Change the API of riscv_set_local_interrupt to take a
write mask and value to allow setting and clearing of
multiple local interrupts atomically in a single call.
Rename the new function to riscv_cpu_update_mip.
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
error_report and friends already add a "qemu-system-xxx" prefix
to the string, so a "qemu:" prefix is redundant in the string.
Just drop it.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1537495530-580-1-git-send-email-maozhongyi@cmss.chinamobile.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
To allow Linux to enumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Set the interrupt-controller ndev to the correct number taken from the
HiFive Unleashed board.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
To allow Linux to ennumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Create a SiFive Unleashed U54 SoC and use that in the sifive_u machine.
We leave the SoC, RAM, device tree and reset/fdt loading as part of the
machine. All the other device creation has been moved to the SoC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Message-Id: <20180625124238.25339-17-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWvLKRQAKCRBr8dezV+8+
TyOrAKCBiArCoNOD0lIvSdgu8Dv7dKOUaQCeMfS/FkM9wSTOnZgOPKPEZ3xreLY=
=wUet
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3' into staging
RISC-V: QEMU 2.13 Minor Fixes
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
# gpg: Signature made Wed 09 May 2018 11:15:33 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3:
riscv: requires libfdt
riscv: htif: increase the priority of the htif subregion
riscv: spike: allow base == 0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sanity check on base doesn't allow htif to be mapped @0. Check if the
symbol exists instead so we can map it where we want.
Reviewed-by: Michael Clark <mjc@sifive.com>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Message-Id: <1525360636-18229-2-git-send-email-frederic.konrad@adacore.com>
The sifive_u machine already marks its ROM readonly however
it has the wrong base address for its mask ROM. This patch
fixes the sifive_u mask ROM base address.
This commit makes all other boards consistently use mask_rom
as the variable name for their ROMs. Boards that use device
tree now check that that the device tree fits in the assigned
ROM space using the new qemu_fdt_totalsize(void *fdt)
interface, adding a bounds check and error message. This
can detect truncation.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <Alistair.Francis@wdc.com>
Removes a whole lot of unnecessary boilerplate code. Machines
don't need to be objects. The expansion of the SOC object model
for the RISC-V machines will happen in the future as SiFive
plans to add their FE310 and FU540 SOCs to QEMU. However, it
seems that this present boilerplate is complete unnecessary.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
When load_elf is called with NULL as an argument to the
address translate callback, it does an identity translation.
This commit removes the redundant identity_translate callback.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Another case of replacing hard coded constants, this time
referring to the definition in the virt machine's memmap.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
This makes 'qemu-system-riscv64 -machine help' output more tidy
and consistent.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V device-tree code has a number of hard-coded
constants and this change moves them into header enums.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Change all the uses of serial_hds[] to go via the new
serial_hd() function. Code change produced with:
find hw -name '*.[ch]' | xargs sed -i -e 's/serial_hds\[\([^]]*\)\]/serial_hd(\1)/g'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-8-peter.maydell@linaro.org
This adds RISC-V into the build system enabling the following targets:
- riscv32-softmmu
- riscv64-softmmu
- riscv32-linux-user
- riscv64-linux-user
This adds defaults configs for RISC-V, enables the build for the RISC-V
CPU core, hardware, and Linux User Emulation. The 'qemu-binfmt-conf.sh'
script is updated to add the RISC-V ELF magic.
Expected checkpatch errors for consistency reasons:
ERROR: line over 90 characters
FILE: scripts/qemu-binfmt-conf.sh
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
This provides a RISC-V Board compatible with the the SiFive Freedom U SDK.
The following machine is implemented:
- 'sifive_u'; CLINT, PLIC, UART, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
This provides a RISC-V Board compatible with the the SiFive Freedom E SDK.
The following machine is implemented:
- 'sifive_e'; CLINT, PLIC, UART, AON, GPIO, QSPI, PWM
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Simple model of the PRCI (Power, Reset, Clock, Interrupt) to emulate
register reads made by the SDK BSP.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
QEMU model of the UART on the SiFive E300 and U500 series SOCs.
BBL supports the SiFive UART for early console access via the SBI
(Supervisor Binary Interface) and the linux kernel SBI console.
The SiFive UART implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machine with device-tree, 16550a UART and VirtIO MMIO.
The following machine is implemented:
- 'virt'; CLINT, PLIC, 16550A UART, VirtIO MMIO, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Test finisher memory mapped device used to exit simulation.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machines compatble with Spike aka riscv-isa-sim, the RISC-V
Instruction Set Simulator. The following machines are implemented:
- 'spike_v1.9.1'; HTIF console, config-string, Privileged ISA Version 1.9.1
- 'spike_v1.10'; HTIF console, device-tree, Privileged ISA Version 1.10
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
The PLIC (Platform Level Interrupt Controller) device provides a
parameterizable interrupt controller based on SiFive's PLIC specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
The CLINT (Core Local Interruptor) device provides real-time clock, timer
and interprocessor interrupts based on SiFive's CLINT specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Holds the state of a heterogenous array of RISC-V hardware threads.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
HTIF (Host Target Interface) provides console emulation for QEMU. HTIF
allows identical copies of BBL (Berkeley Boot Loader) and linux to run
on both Spike and QEMU. BBL provides HTIF console access via the
SBI (Supervisor Binary Interface) and the linux kernel SBI console.
The HTIT chardev implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
