AST2600 Display Port MCU introduces 0x18000000~0x1803FFFF as it's memory
and io address. If guest machine try to access DPMCU memory, it will
cause a fatal error.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20211210083034.726610-1-troy_lee@aspeedtech.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the enums to match the naming style used by QAPI, and to
use "32" and "64" instead of "20" and "31". This will allow us
to more easily move the enum to the QAPI schema later.
About the naming choice: "SMBIOS 2.1 entry point"/"SMBIOS 3.0
entry point" and "32-bit entry point"/"64-bit entry point" are
synonymous in the SMBIOS specification. However, the phrases
"32-bit entry point" and "64-bit entry point" are used more often.
The new names also avoid confusion between the entry point format
and the actual SMBIOS version reported in the entry point
structure. For example: currently the 32-bit entry point
actually report SMBIOS 2.8 support, not 2.1.
Based on portions of a patch submitted by Daniel P. Berrangé.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-2-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 7.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211217143948.289995-1-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
The aspeed machines connects backends with drive_get_next() in several
counting loops, one of them in a helper function, and a conditional.
Change it to use drive_get() directly. This makes the unit numbers
explicit in the code.
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-13-armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-zcu102" connects backends with drive_get_next() in two
counting loops, one of them in a helper function. Change it to use
drive_get() directly. This makes the unit numbers explicit in the
code.
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-12-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-zcu102" connects backends with drive_get_next() in
several counting loops. Change it to use drive_get() directly. This
makes the unit numbers explicit in the code.
Cc: Alistair Francis <alistair@alistair23.me>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-11-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To propagate errors to the caller of the pre_plug callback, use the
object_poperty_set*() functions directly instead of the qdev_prop_set*()
helpers.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-5-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We do not support instantiating multiple IOMMUs. Before adding a
virtio-iommu, check that no other IOMMU is present. This will detect
both "iommu=smmuv3" machine parameter and another virtio-iommu instance.
Fixes: 70e89132c9 ("hw/arm/virt: Add the virtio-iommu device tree mappings")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio-iommu is now supported with ACPI VIOT as well as device tree.
Remove the restriction that prevents from instantiating a virtio-iommu
device under ACPI.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a virtio-iommu is instantiated, describe it using the ACPI VIOT
table.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A lot of C files in hw/arm include qemu-common.h when they don't
need anything from it. Drop the include lines.
omap1.c, pxa2xx.c and strongarm.c retain the include because they
use it for the prototype of qemu_get_timedate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-id: 20211129200510.1233037-5-peter.maydell@linaro.org
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-versal-virt" connects backends with drive_get_next() in
a counting loop. Change it to use drive_get() directly. This makes
the unit numbers explicit in the code.
Cc: Alistair Francis <alistair@alistair23.me>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-9-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "mcimx7d-sabre" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-8-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "mcimx6ul-evk" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-7-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "imx25-pdk" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-6-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
The versatile and vexpress machines ("versatileab", "versatilepb",
"vexpress-a9", "vexpress-a15") connect just one or two backends of a
type with drive_get_next(). Change them to use drive_get() directly.
This makes the unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-5-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "quanta-gbs-bmc" connects just one backend with
drive_get_next(), but with a helper function. Change it to use
drive_get() directly. This makes the unit numbers explicit in the
code.
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Tyrone Ting <kfting@nuvoton.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-4-armbru@redhat.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
A number of machines connect just one backend with drive_get_next().
Change them to use drive_get() directly. This makes the (zero) unit
number explicit in the code.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Cc: Niek Linnenbank <nieklinnenbank@gmail.com>
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-3-armbru@redhat.com>
ssi_sd_realize() creates an "sd-card" device. This is inappropriate,
and marked FIXME.
Move it to the boards that create these devices. Prior art: commit
eb4f566bbb for device "generic-sdhci", and commit 26c607b86b for
device "pl181".
The device remains not user-creatable, because its users should (and
do) wire up its GPIO chip-select line.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The virt machine has properties to enable MTE and Nested Virtualization
support. However, its check to ensure the backing accel implementation
supports it today only looks for KVM and bails out if it finds it.
Extend the checks to HVF as well as it does not support either today.
This will cause QEMU to print a useful error message rather than
silently ignoring the attempt by the user to enable either MTE or
the Virtualization extensions.
Reported-by: saar amar <saaramar5@gmail.com>
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20211123122859.22452-1-agraf@csgraf.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit d8fb7d0969 ("vl: switch -M parsing to keyval"), machine
parameter definitions cannot use underscores, because keyval_dashify()
transforms them to dashes and the parser doesn't find the parameter.
This affects option default_bus_bypass_iommu which was introduced in the
same release:
$ qemu-system-aarch64 -M virt,default_bus_bypass_iommu=on
qemu-system-aarch64: Property 'virt-6.1-machine.default-bus-bypass-iommu' not found
Rename the parameter to "default-bus-bypass-iommu". Passing
"default_bus_bypass_iommu" is still valid since the underscore are
transformed automatically.
Fixes: 6d7a85483a ("hw/arm/virt: Add default_bus_bypass_iommu machine option")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211026093733.2144161-1-jean-philippe@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* New fp5280g2-bmc board (John)
* Small cleanup in Aspeed SMC model (Cedric)
-----BEGIN PGP SIGNATURE-----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=qbBN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/clg/tags/pull-aspeed-20211022' into staging
Aspeed patches :
* New fp5280g2-bmc board (John)
* Small cleanup in Aspeed SMC model (Cedric)
# gpg: Signature made Fri 22 Oct 2021 12:55:18 AM PDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/clg/tags/pull-aspeed-20211022:
speed/sdhci: Add trace events
aspeed/smc: Use a container for the flash mmio address space
aspeed: Add support for the fp5280g2-bmc board
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The fp5280g2-bmc is supported by OpenBMC, It's
based on the following device tree
https://github.com/openbmc/linux/blob/dev-5.10/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
Signed-off-by: John Wang <wangzhiqiang02@inspur.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211014064548.934799-1-wangzhiqiang02@inspur.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generate the Processor Properties Topology Table (PPTT) for ARM
virt machines supporting it (>= 6.2).
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20211020142125.7516-8-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Support device tree CPU topology descriptions.
In accordance with the Devicetree Specification, the Linux Doc
"arm/cpus.yaml" requires that cpus and cpu nodes in the DT are
present. And we have already met the requirement by generating
/cpus/cpu@* nodes for members within ms->smp.cpus. Accordingly,
we should also create subnodes in cpu-map for the present cpus,
each of which relates to an unique cpu node.
The Linux Doc "cpu/cpu-topology.txt" states that the hierarchy
of CPUs in a SMP system is defined through four entities and
they are socket/cluster/core/thread. It is also required that
a socket node's child nodes must be one or more cluster nodes.
Given that currently we are only provided with information of
socket/core/thread, we assume there is one cluster child node
in each socket node when creating cpu-map.
Co-developed-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211020142125.7516-4-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
On existing older machine types, without cpu topology described
in ACPI or DT, the guest will populate one by default. With the
topology described, it will read the information and set up its
topology as instructed, but that may not be the same as what was
getting used by default. It's possible that an user application
has a dependency on the default topology and if the default one
gets changed it will probably behave differently.
Based on above consideration we'd better only describe topology
information to the guest on 6.2 and later machine types.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20211020142125.7516-2-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
ARM SBBR specification mandates DBG2 table (Debug Port Table 2)
since v1.0 (ARM DEN0044F 8.3.1.7 DBG2).
The DBG2 table allows to describe one or more debug ports.
Generate an DBG2 table featuring a single debug port, the PL011.
The DBG2 specification can be found at
"Microsoft Debug Port Table 2 (DBG2)"
https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/acpi-debug-port-table?redirectedfrom=MSDN
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20211019080037.930641-3-eric.auger@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The empty NUMA node, where no memory resides, are allowed. For
example, the following command line specifies two empty NUMA nodes.
With this, QEMU fails to boot because of the conflicting device-tree
node names, as the following error message indicates.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host \
-cpu host -smp 4,sockets=2,cores=2,threads=1 \
-m 1024M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-numa node,nodeid=0,cpus=0-1,memdev=mem0 \
-numa node,nodeid=1,cpus=2-3,memdev=mem1 \
-numa node,nodeid=2 \
-numa node,nodeid=3
:
qemu-system-aarch64: FDT: Failed to create subnode /memory@80000000: FDT_ERR_EXISTS
As specified by linux device-tree binding document, the device-tree
nodes for these empty NUMA nodes shouldn't be generated. However,
the corresponding NUMA node IDs should be included in the distance
map. The memory hotplug through device-tree on ARM64 isn't existing
so far and it's not necessary to require the user to provide a distance
map. Furthermore, the default distance map Linux generates may even be
sufficient. So this simply skips populating the device-tree nodes for
these empty NUMA nodes to avoid the error, so that QEMU can be started
successfully.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20211015124246.23073-1-gshan@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Upgrade the IORT table from B to E.b specification
revision (ARM DEN 0049E.b).
The SMMUv3 and root complex node have additional
fields. Also unique IORT node identifiers are
introduced: they are generated in sequential order.
They are not cross-referenced though.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20211014115643.756977-3-eric.auger@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
DeviceState.id is a pointer to a string that is stored in the QemuOpts
object DeviceState.opts and freed together with it. We want to create
devices without going through QemuOpts in the future, so make this a
separately allocated string.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211008133442.141332-9-kwolf@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AspeedSMCFlash::size is only used to compute the initial size of the
boot_rom region. Not very useful, so directly call memory_region_size()
instead.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no need to keep a reference of the flash qdev in the AspeedSMCFlash
state: the SPI bus takes ownership and will release its resources. Remove
AspeedSMCFlash::flash.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The characteristics of the Aspeed controllers are described in a
AspeedSMCController structure which is redundant with the
AspeedSMCClass. Move all attributes under the class and adapt the code
to use class attributes instead.
This is a large change but it is functionally equivalent.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-33-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
PS:
Spec is Microsoft hosted, however 1.02 is no where to be found
(MS lists only the current revision) and the current revision is 1.07,
so bring comments in line with 1.07 as this is the only available spec.
There is no content change between originally implemented 1.02
(using QEMU code as reference) and 1.07. The only change is renaming
'Reserved2' field to 'Language', with the same 0 value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-32-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
implicit cast to structure uint8_t member didn't raise error when
assigning value from incorrect enum, but when using build_append_gas()
(next patch) it will error out with (clang):
implicit conversion from enumeration type 'AmlRegionSpace'
to different enumeration type 'AmlAddressSpace'
fix cast error by using correct AML_AS_SYSTEM_MEMORY enum
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-31-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building IORT table use endian agnostic build_append_int_noprefix()
API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210924122802.1455362-30-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-29-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-28-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building MADT table for arm/x86 and use endian agnostic
build_append_int_noprefix() API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-26-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-22-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building SRAT tables for arm/x86 and use endian agnostic
build_append_int_noprefix() API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-18-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
While at it switch to build_append_int_noprefix() to build
table entries (which also removes some manual offset
calculations)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-17-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we have a common structure SMPCompatProps used to store information
about SMP compatibility stuff, so we can also move smp_prefer_sockets
there for cleaner code.
No functional change intended.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-15-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the real SMP hardware topology world, it's much more likely that
we have high cores-per-socket counts and few sockets totally. While
the current preference of sockets over cores in smp parsing results
in a virtual cpu topology with low cores-per-sockets counts and a
large number of sockets, which is just contrary to the real world.
Given that it is better to make the virtual cpu topology be more
reflective of the real world and also for the sake of compatibility,
we start to prefer cores over sockets over threads in smp parsing
since machine type 6.2 for different arches.
In this patch, a boolean "smp_prefer_sockets" is added, and we only
enable the old preference on older machines and enable the new one
since type 6.2 for all arches by using the machine compat mechanism.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-10-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Linux spi-imx driver does not work on QEMU. The reason is that the
state of m25p80 loops in STATE_READING_DATA state after receiving
RDSR command, the new command is ignored. Before sending a new command,
CS line should be pulled high to make the state of m25p80 back to IDLE.
Currently the SPI flash CS line is connected to the SPI controller, but
on the real board, it's connected to GPIO3_19. This matches the ecspi1
device node in the board dts.
ecspi1 node in imx6qdl-sabrelite.dtsi:
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash: m25p80@0 {
compatible = "sst,sst25vf016b", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
Should connect the SSI_GPIO_CS to GPIO3_19 when adding a spi-nor to
spi1 on sabrelite machine.
Verified this patch on Linux v5.14.
Logs:
# echo "01234567899876543210" > test
# mtd_debug erase /dev/mtd0 0x0 0x1000
Erased 4096 bytes from address 0x00000000 in flash
# mtd_debug write /dev/mtdblock0 0x0 20 test
Copied 20 bytes from test to address 0x00000000 in flash
# mtd_debug read /dev/mtdblock0 0x0 20 test_out
Copied 20 bytes from address 0x00000000 in flash to test_out
# cat test_out
01234567899876543210#
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210927142825.491-1-xchengl.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for ZynqMP eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=3,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 768 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-9-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Xilinx ZynqMP Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=2,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-8-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=1,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 3072 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-7-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=0,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-6-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 SoC uses Cortex-A7 cores which support virtualization.
However, today we are configuring QEMU to use HVC as PSCI conduit.
That means HVC calls get trapped into QEMU instead of the guest's own
emulated CPU and thus break the guest's ability to execute virtualization.
Fix this by moving to SMC as conduit, freeing up HYP completely to the VM.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20210920203931.66527-1-agraf@csgraf.de
Fixes: 740dafc0ba ("hw/arm: add Allwinner H3 System-on-Chip")
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The various MPS2 boards implemented in mps2.c have multiple I2C
buses: a bus dedicated to the audio configuration, one for the LCD
touchscreen controller, and two which are connected to the external
Shield expansion connector. Mark the buses which are used only for
board-internal devices as 'full' so that if the user creates i2c
devices on the commandline without specifying a bus name then they
will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-5-peter.maydell@linaro.org
The various MPS2 boards have multiple I2C buses: typically a bus
dedicated to the audio configuration, one for the LCD touchscreen
controller, one for a DDR4 EEPROM, and two which are connected to the
external Shield expansion connector. Mark the buses which are used
only for board-internal devices as 'full' so that if the user creates
i2c devices on the commandline without specifying a bus name then
they will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-4-peter.maydell@linaro.org
The mps2-tz boards use a data-driven structure to create the devices
that sit behind peripheral protection controllers. Currently the
functions which create these devices are passed an 'opaque' pointer
which is always the address within the machine struct of the device
to create, and some "all devices need this" information like irqs and
addresses.
If a specific device needs more information than this, it is
currently not possible to pass that through from the PPCInfo
data structure. Add support for passing an extra data parameter,
so that we can more flexibly handle the needs of specific
device types. To provide some type-safety we make this extra
parameter a pointer to a union (which initially has no members).
In particular, we would like to be able to indicate which of the
i2c controllers are for on-board devices only and which are
connected to the external 'shield' expansion port; a subsequent
patch will use this mechanism for that purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-3-peter.maydell@linaro.org
Included creation of ITS as part of virt platform GIC
initialization. This Emulated ITS model now co-exists with kvm
ITS and is enabled in absence of kvm irq kernel support in a
platform.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-9-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All the devices that used to use system_clock_scale have now been
converted to use Clock inputs instead, so the global is no longer
needed; remove it and all the code that sets it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210812093356.1946-26-peter.maydell@linaro.org
The stellaris-gptm timer currently uses system_clock_scale for one of
its timer modes where the timer runs at the CPU clock rate. Make it
use a Clock input instead.
We don't try to make the timer handle changes in the clock frequency
while the downcounter is running. This is not a change in behaviour
from the previous system_clock_scale implementation -- we will pick
up the new frequency only when the downcounter hits zero. Handling
dynamic clock changes when the counter is running would require state
that the current gptm implementation doesn't have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-25-peter.maydell@linaro.org
The implementation of the Stellaris general purpose timer module
device stellaris-gptm is currently in the same source file as the
board model. Split it out into its own source file in hw/timer.
Apart from the new file comment headers and the Kconfig and
meson.build changes, this is just code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-24-peter.maydell@linaro.org
Fix the code style issues in the Stellaris general purpose timer
module code, so that when we move it to a different file in a
following patch checkpatch doesn't complain.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-23-peter.maydell@linaro.org
Wire up the refclk for the msf2 SoC. This SoC runs the refclk at a
frequency which is programmably either /4, /8, /16 or /32 of the main
CPU clock. We don't currently model the register which allows the
guest to set the divisor, so implement the refclk as a fixed /32 of
the CPU clock (which is the value of the divisor at reset).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-21-peter.maydell@linaro.org
Instead of passing the MSF2 SoC an integer property specifying the
CPU clock rate, pass it a Clock instead. This lets us wire that
clock up to the armv7m object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-20-peter.maydell@linaro.org
In the realize method of the msf2-soc SoC object, we call g_new() to
create new MemoryRegion objects for the nvm, nvm_alias, and sram.
This is unnecessary; make these MemoryRegions member fields of the
device state struct instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-19-peter.maydell@linaro.org
Connect the sysclk to the armv7m object. This board's SoC does not
connect up the systick reference clock, so we don't need to connect a
refclk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-18-peter.maydell@linaro.org
Currently the stellaris_sys_init() function creates the
TYPE_STELLARIS_SYS object, sets its properties, realizes it, maps its
MMIO region and connects its IRQ. In order to support wiring the
sysclk up to the armv7m object, we need to split this function apart,
because to connect the clock output of the STELLARIS_SYS object to
the armv7m object we need to create the STELLARIS_SYS object before
the armv7m object, but we can't wire up the IRQ until after we've
created the armv7m object.
Remove the stellaris_sys_init() function, and instead put the
create/configure/realize parts before we create the armv7m object and
the mmio/irq connection parts afterwards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-17-peter.maydell@linaro.org
Wire up the sysclk input to the armv7m object.
Strictly this SoC should not have a systick device at all, but our
armv7m container object doesn't currently support disabling the
systick device. For the moment, add a TODO comment, but note that
this is why we aren't wiring up a refclk (no need for one).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Message-id: 20210812093356.1946-16-peter.maydell@linaro.org
Delete the trailing blank line at the end of the source file.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-15-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f405 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the netduinoplus2 board where the
systick reference clock was running at 1MHz rather than 21MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-14-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f205 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the netduino2 board where the systick
reference clock was running at 1MHz rather than 15MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-13-peter.maydell@linaro.org
Wire up the sysclk and refclk for the stm32f100 SoC. This SoC always
runs the systick refclk at 1/8 the frequency of the main CPU clock,
so the board code only needs to provide a single sysclk clock.
Because there is only one board using this SoC, we convert the SoC
and the board together, rather than splitting it into "add clock to
SoC; connect clock in board; add error check in SoC code that clock
is wired up".
When the systick device starts honouring its clock inputs, this will
fix an emulation inaccuracy in the stm32vldiscovery board where the
systick reference clock was running at 1MHz rather than 3MHz.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-12-peter.maydell@linaro.org
In the realize methods of the stm32f100 and stm32f205 SoC objects, we
call g_new() to create new MemoryRegion objects for the sram, flash,
and flash_alias. This is unnecessary (and leaves open the
possibility of leaking the allocations if we exit from realize with
an error). Make these MemoryRegions member fields of the device
state struct instead, as stm32f405 already does.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-11-peter.maydell@linaro.org
Connect up the armv7m clocks on the mps2-an385/386/500/511.
Connect up the armv7m object's clocks on the MPS boards defined in
mps2.c. The documentation for these FPGA images doesn't specify what
systick reference clock is used (if any), so for the moment we
provide a 1MHz refclock, which will result in no behavioural change
from the current hardwired 1MHz clock implemented in
armv7m_systick.c:systick_scale().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-9-peter.maydell@linaro.org
Wire up the cpuclk for the systick devices to the SSE object's
existing mainclk clock.
We do not wire up the refclk because the SSE subsystems do not
provide a refclk. (This is documented in the IoTKit and SSE-200
TRMs; the SSE-300 TRM doesn't mention it but we assume it follows the
same approach.) When we update the systick device later to honour "no
refclk connected" this will fix a minor emulation inaccuracy for the
SSE-based boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-8-peter.maydell@linaro.org
Create input clocks on the armv7m container object which pass through
to the systick timers, so that users of the armv7m object can specify
the clocks being used.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-7-peter.maydell@linaro.org
Instead of having the NVIC device provide a single sysbus memory
region covering the whole of the "System PPB" space, which implements
the default behaviour for unimplemented ranges and provides the NS
alias window to the sysregs as well as the main sysreg MR, move this
handling to the container armv7m device. The NVIC now provides a
single memory region which just implements the system registers.
This consolidates all the handling of "map various devices in the
PPB" into the armv7m container where it belongs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-4-peter.maydell@linaro.org
There's no particular reason why the NVIC should be owning the
SysTick device objects; move them into the ARMv7M container object
instead, as part of consolidating the "create the devices which are
built into an M-profile CPU and map them into their architected
locations in the address space" work into one place.
This involves temporarily creating a duplicate copy of the
nvic_sysreg_ns_ops struct and its read/write functions (renamed as
v7m_sysreg_ns_*), but we will delete the NVIC's copy of this code in
a subsequent patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-3-peter.maydell@linaro.org
Currently we implement the RAS register block within the NVIC device.
It isn't really very tightly coupled with the NVIC proper, so instead
move it out into a sysbus device of its own and have the top level
ARMv7M container create it and map it into memory at the right
address.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-2-peter.maydell@linaro.org
Add -cpu a64fx to use A64FX processor when -machine virt option is
specified. In addition, add a64fx to the Supported guest CPU types
in the virt.rst document.
Signed-off-by: Shuuichirou Ishii <ishii.shuuichir@fujitsu.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 6.2 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the raspi2/raspi3 machine aliases,
deprecated since commit 155e1c82ed.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210827060815.2384760-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the CPU realize function will fail cleanly if we ask for EL3
when KVM is enabled, we don't need to check for errors explicitly in
the virt board code. The reported message is slightly different;
it is now:
qemu-system-aarch64: Cannot enable KVM when guest CPU has EL3 enabled
instead of:
qemu-system-aarch64: mach-virt: KVM does not support Security extensions
We don't delete the MTE check because there the logic is more
complex; deleting the check would work but makes the error message
less helpful, as it would read:
qemu-system-aarch64: MTE requested, but not supported by the guest CPU
instead of:
qemu-system-aarch64: mach-virt: KVM does not support providing MTE to the guest CPU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210816135842.25302-4-peter.maydell@linaro.org
The SoC realize can fail for legitimate reasons, because it propagates
errors up from CPU realize, which in turn can be provoked by user
error in setting commandline options. Use error_fatal so we report
the error message to the user and exit, rather than asserting
via error_abort.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210816135842.25302-2-peter.maydell@linaro.org
Since commit
36b79e3219 ("hw/acpi/Kconfig: Add missing Kconfig dependencies (build error)"),
ACPI_MEMORY_HOTPLUG and ACPI_NVDIMM is implicitly turned on when
ACPI_HW_REDUCED is selected. ACPI_HW_REDUCED is already enabled. No need to
turn on ACPI_MEMORY_HOTPLUG or ACPI_NVDIMM explicitly. This is a minor cleanup.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210819162637.518507-1-ani@anisinha.ca
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simplify by always passing a MemoryRegion property to the device.
Doing so we can move the AddressSpace field to the device struct,
removing need for heap allocation.
Update the Xilinx ZynqMP / Versal SoC models to pass the default
system memory instead of a NULL value.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210819163422.2863447-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Simplify by always passing a MemoryRegion property to the device.
Doing so we can move the AddressSpace field to the device struct,
removing need for heap allocation.
Update the Xilinx ZynqMP SoC model to pass the default system
memory instead of a NULL value.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210819163422.2863447-4-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we link QOM object (a) as a property of QOM object (b),
we must set the property *before* (b) is realized.
Move QSPI realization *after* QSPI DMA.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210819163422.2863447-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SBSA_GWDT enum value conflicts with the SBSA_GWDT() QOM type
checking helper, preventing us from using a OBJECT_DEFINE* or
DEFINE_INSTANCE_CHECKER macro for the SBSA_GWDT() wrapper.
If I understand the SBSA 6.0 specification correctly, the signal
being connected to IRQ 16 is the WS0 output signal from the
Generic Watchdog. Rename the enum value to SBSA_GWDT_WS0 to be
more explicit and avoid the name conflict.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20210806023119.431680-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add property memory region which can connect with IOMMU region to support SMMU translate.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 4C23C17B8E87E74E906A25A3254A03F4FA1FEC31@SHASXM03.verisilicon.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate SAI1/2/3 and ASRC as unimplemented devices to avoid random
Linux kernel crashes, such as
Unhandled fault: external abort on non-linefetch (0x808) at 0xd1580010
pgd = (ptrval)
[d1580010] *pgd=8231b811, *pte=02034653, *ppte=02034453
Internal error: : 808 [#1] SMP ARM
...
[<c095e974>] (regmap_mmio_write32le) from [<c095eb48>] (regmap_mmio_write+0x3c/0x54)
[<c095eb48>] (regmap_mmio_write) from [<c09580f4>] (_regmap_write+0x4c/0x1f0)
[<c09580f4>] (_regmap_write) from [<c095837c>] (_regmap_update_bits+0xe4/0xec)
[<c095837c>] (_regmap_update_bits) from [<c09599b4>] (regmap_update_bits_base+0x50/0x74)
[<c09599b4>] (regmap_update_bits_base) from [<c0d3e9e4>] (fsl_asrc_runtime_resume+0x1e4/0x21c)
[<c0d3e9e4>] (fsl_asrc_runtime_resume) from [<c0942464>] (__rpm_callback+0x3c/0x108)
[<c0942464>] (__rpm_callback) from [<c0942590>] (rpm_callback+0x60/0x64)
[<c0942590>] (rpm_callback) from [<c0942b60>] (rpm_resume+0x5cc/0x808)
[<c0942b60>] (rpm_resume) from [<c0942dfc>] (__pm_runtime_resume+0x60/0xa0)
[<c0942dfc>] (__pm_runtime_resume) from [<c0d3ecc4>] (fsl_asrc_probe+0x2a8/0x708)
[<c0d3ecc4>] (fsl_asrc_probe) from [<c0935b08>] (platform_probe+0x58/0xb8)
[<c0935b08>] (platform_probe) from [<c0933264>] (really_probe.part.0+0x9c/0x334)
[<c0933264>] (really_probe.part.0) from [<c093359c>] (__driver_probe_device+0xa0/0x138)
[<c093359c>] (__driver_probe_device) from [<c0933664>] (driver_probe_device+0x30/0xc8)
[<c0933664>] (driver_probe_device) from [<c0933c88>] (__driver_attach+0x90/0x130)
[<c0933c88>] (__driver_attach) from [<c0931060>] (bus_for_each_dev+0x78/0xb8)
[<c0931060>] (bus_for_each_dev) from [<c093254c>] (bus_add_driver+0xf0/0x1d8)
[<c093254c>] (bus_add_driver) from [<c0934a30>] (driver_register+0x88/0x118)
[<c0934a30>] (driver_register) from [<c01022c0>] (do_one_initcall+0x7c/0x3a4)
[<c01022c0>] (do_one_initcall) from [<c1601204>] (kernel_init_freeable+0x198/0x22c)
[<c1601204>] (kernel_init_freeable) from [<c0f5ff2c>] (kernel_init+0x10/0x128)
[<c0f5ff2c>] (kernel_init) from [<c010013c>] (ret_from_fork+0x14/0x38)
or
Unhandled fault: external abort on non-linefetch (0x808) at 0xd19b0000
pgd = (ptrval)
[d19b0000] *pgd=82711811, *pte=308a0653, *ppte=308a0453
Internal error: : 808 [#1] SMP ARM
...
[<c095e974>] (regmap_mmio_write32le) from [<c095eb48>] (regmap_mmio_write+0x3c/0x54)
[<c095eb48>] (regmap_mmio_write) from [<c09580f4>] (_regmap_write+0x4c/0x1f0)
[<c09580f4>] (_regmap_write) from [<c0959b28>] (regmap_write+0x3c/0x60)
[<c0959b28>] (regmap_write) from [<c0d41130>] (fsl_sai_runtime_resume+0x9c/0x1ec)
[<c0d41130>] (fsl_sai_runtime_resume) from [<c0942464>] (__rpm_callback+0x3c/0x108)
[<c0942464>] (__rpm_callback) from [<c0942590>] (rpm_callback+0x60/0x64)
[<c0942590>] (rpm_callback) from [<c0942b60>] (rpm_resume+0x5cc/0x808)
[<c0942b60>] (rpm_resume) from [<c0942dfc>] (__pm_runtime_resume+0x60/0xa0)
[<c0942dfc>] (__pm_runtime_resume) from [<c0d4231c>] (fsl_sai_probe+0x2b8/0x65c)
[<c0d4231c>] (fsl_sai_probe) from [<c0935b08>] (platform_probe+0x58/0xb8)
[<c0935b08>] (platform_probe) from [<c0933264>] (really_probe.part.0+0x9c/0x334)
[<c0933264>] (really_probe.part.0) from [<c093359c>] (__driver_probe_device+0xa0/0x138)
[<c093359c>] (__driver_probe_device) from [<c0933664>] (driver_probe_device+0x30/0xc8)
[<c0933664>] (driver_probe_device) from [<c0933c88>] (__driver_attach+0x90/0x130)
[<c0933c88>] (__driver_attach) from [<c0931060>] (bus_for_each_dev+0x78/0xb8)
[<c0931060>] (bus_for_each_dev) from [<c093254c>] (bus_add_driver+0xf0/0x1d8)
[<c093254c>] (bus_add_driver) from [<c0934a30>] (driver_register+0x88/0x118)
[<c0934a30>] (driver_register) from [<c01022c0>] (do_one_initcall+0x7c/0x3a4)
[<c01022c0>] (do_one_initcall) from [<c1601204>] (kernel_init_freeable+0x198/0x22c)
[<c1601204>] (kernel_init_freeable) from [<c0f5ff2c>] (kernel_init+0x10/0x128)
[<c0f5ff2c>] (kernel_init) from [<c010013c>] (ret_from_fork+0x14/0x38)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20210810160318.87376-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the user provides both a BIOS/firmware image and also a guest
kernel filename, arm_setup_firmware_boot() will pass the
kernel image to the firmware via the fw_cfg device. However we
weren't checking whether there really was a fw_cfg device present,
and if there wasn't we would crash.
This crash can be provoked with a command line such as
qemu-system-aarch64 -M raspi3 -kernel /dev/null -bios /dev/null -display none
It is currently only possible on the raspi3 machine, because unless
the machine sets info->firmware_loaded we won't call
arm_setup_firmware_boot(), and the only machines which set that are:
* virt (has a fw-cfg device)
* sbsa-ref (checks itself for kernel_filename && firmware_loaded)
* raspi3 (crashes)
But this is an unfortunate beartrap to leave for future machine
model implementors, so we should handle this situation in boot.c.
Check in arm_setup_firmware_boot() whether the fw-cfg device exists
before trying to load files into it, and if it doesn't exist then
exit with a hopefully helpful error message.
Because we now handle this check in a machine-agnostic way, we
can remove the check from sbsa-ref.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/503
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210726163351.32086-1-peter.maydell@linaro.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210726150953.1218690-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bit to see if a CD is valid is the last bit of the first word of the CD.
Signed-off-by: Joe Komlodi <joe.komlodi@xilinx.com>
Message-id: 1626728232-134665-2-git-send-email-joe.komlodi@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
added a dependency on the TYPE_IMX_USDHC model, but forgot to add
the Kconfig selector. Fix that to solve when built stand-alone:
$ qemu-system-arm -M imx25-pdk
qemu-system-arm: missing object type 'imx-usdhc'
Aborted (core dumped)
Fixes: bfae1772c4 ("hw/arm/fsl-imx25: Wire up eSDHC controllers")
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-6-philmd@redhat.com>
In commit c4f00daa5b ("imx25-pdk: create ds1338 for qtest inside
the test") we removed the DS1338 device from the i.MX25 machine
but forgot to remove it in the machine Kconfig definitions, do
it now.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-5-philmd@redhat.com>
The TYPE_NPCM7XX_SMBUS device model exposes an SMBus, but
this isn't advertised with proper Kconfig symbol, leading
to an early build failure when building NPCM7XX machines
standalone:
The following clauses were found for AT24C
config AT24C depends on I2C
select AT24C if NPCM7XX
Fix by adding SMBUS to NPCM7XX.
Fixes: 94e7787939 ("hw/i2c: Implement NPCM7XX SMBus Module Single Mode")
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-4-philmd@redhat.com>
When we build IORT table with SMMUv3 and bypass iommu feature enabled,
we can no longer setup one map from RC to SMMUv3 covering the whole RIDs.
We need to walk the PCI bus and check whether the root bus will bypass
iommu, setup RC -> SMMUv3 -> ITS map for RC which will not bypass iommu.
When a SMMUv3 node exist, we setup the idmap from SMMUv3 to ITS
covering the whole RIDs, and only modify the map from RC to SMMUv3.
We build RC -> SMMUv3 -> ITS map for root bus with bypass_iommu
disabled, and build idmap from RC to ITS directly for the rest of
the whole RID space.
For example we run qemu with command line:
qemu/build/aarch64-softmmu/qemu-system-aarch64 \
-kernel arch/arm64/boot/Image \
-enable-kvm \
-cpu host \
-m 8G \
-smp 8,sockets=2,cores=4,threads=1 \
-machine virt,kernel_irqchip=on,gic-version=3,iommu=smmuv3,default_bus_bypass_iommu=true \
-drive file=./QEMU_EFI-pflash.raw,if=pflash,format=raw,unit=0,readonly=on \
-device pxb-pcie,bus_nr=0x10,id=pci.10,bus=pcie.0,addr=0x3.0x1 \
-device pxb-pcie,bus_nr=0x20,id=pci.20,bus=pcie.0,addr=0x3.0x2,bypass_iommu=true \
-device pcie-root-port,port=0x20,chassis=1,id=pci.1,bus=pcie.0,addr=0x2 \
-device pcie-root-port,port=0x20,chassis=11,id=pci.11,bus=pci.10,addr=0x1 \
-device pcie-root-port,port=0x20,chassis=21,id=pci.21,bus=pci.20,addr=0x1 \
-device virtio-scsi-pci,id=scsi0,bus=pci.1,addr=0x1 \
-device virtio-scsi-pci,id=scsi1,bus=pci.11,addr=0x1 \
-device virtio-scsi-pci,id=scsi2,bus=pci.21,addr=0x1 \
-initrd /mnt/davinci/wxg/kill-linux/rootfs/mfs.cpio.gz \
-nographic \
-append "rdinit=init console=ttyAMA0 earlycon=pl011,0x9000000 nokaslr" \
And we get guest configuration:
-+-[0000:20]---01.0-[21]--
+-[0000:10]---01.0-[11]--
\-[0000:00]-+-00.0 Device 1b36:0008
+-01.0 Device 1af4:1000
\-02.0-[01]--
With bypass_iommu enabled, the attached devices will bypass iommu.
/sys/class/iommu/smmu3.0x0000000009050000/
|-- device -> ../../../arm-smmu-v3.0.auto
|-- devices
| `-- 0000:10:01.0 -> ../../../../../pci0000:10/0000:10:01.0
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1625748919-52456-7-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a default_bus_bypass_iommu machine option to enable/disable
bypass_iommu for default root bus. The option is disabled by
default and can be enabled with:
$QEMU -machine virt,iommu=smmuv3,default_bus_bypass_iommu=true
Signed-off-by: Xingang Wang <wangxingang5@huawei.com>
Message-Id: <1625748919-52456-4-git-send-email-wangxingang5@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
-----BEGIN PGP SIGNATURE-----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=8708
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging
Some qemu updates for IPMI and I2C
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently select CONFIG_V7M for a bunch of our m-profile devices.
The last sticking point is translate.c which cannot be compiled
without expecting v7m support. Express this dependency in Kconfig
rather than in default devices as a stepping stone to a fully
configurable translate.c.
While we are at it we also need to select ARM_COMPATIBLE_SEMIHOSTING
as that is implied for M profile machines.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210707131744.26027-4-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need this functionality due to:
/* XRAM IRQs get ORed into a single line. */
object_initialize_child(OBJECT(s), "xram-irq-orgate",
&s->lpd.xram.irq_orgate, TYPE_OR_IRQ);
Fixes: a55b441b2c ("hw/arm: versal: Add support for the XRAMs")
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707131744.26027-3-alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The stellaris board doesn't emulate the handling of the OLED
chipselect line correctly. Expand the comment describing this,
including a sketch of the theoretical correct way to do it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the virt board we have two PL061 devices -- one for NonSecure which
is inputs only, and one for Secure which is outputs only. For the former,
we don't care whether its outputs are pulled low or high when the line is
configured as an input, because we don't connect them. For the latter,
we do care, because we wire the lines up to the gpio-pwr device, which
assumes that level 1 means "do the action" and 1 means "do nothing".
For consistency in case we add more outputs in future, configure both
PL061s to pull GPIO lines down to 0.
Reported-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Define TYPE_LM8323 in the public "hw/input/lm832x.h"
header and use it in hw/arm/nseries.c.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
lm832x_key_event() is specific go LM832x devices, not to the
I2C bus API. Move it out of "i2c.h" to a new header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This is just enough to make reboot and poweroff work. Works for
linux, u-boot, and the arm trusted firmware. Not tested, but should
work for plan9, and bare-metal/hobby OSes, since they seem to generally
do what linux does for reset.
The watchdog timer functionality is not yet implemented.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/64
Signed-off-by: Nolan Leake <nolan@sigbus.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210625210209.1870217-1-nolan@sigbus.net
[PMM: tweaked commit title; fixed region size to 0x200;
moved header file to include/]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Lots of this are expected to be coming in, create a directory for them.
Also move the tmp105.h file into the include directory where it
should be.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
It's an adc, put it where it belongs.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's an ADC, put it where it belongs.
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Adds the pca954x muxes expected.
Tested: Booted quanta-q71l image to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20210608202522.2677850-4-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds comments to the board init to identify missing i2c devices.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20210608202522.2677850-2-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a comment and i2c method that describes the board layout.
Tested: firmware booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Brandon Kim <brandonkim@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210608193605.2611114-3-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210614191335.1968807-3-stefanb@linux.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The official punctuation for Arm CPU names uses a hyphen, like
"Cortex-A9". We mostly follow this, but in a few places usage
without the hyphen has crept in. Fix those so we consistently
use the same way of writing the CPU name.
This commit was created with:
git grep -z -l 'Cortex ' | xargs -0 sed -i 's/Cortex /Cortex-/'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210527095152.10968-1-peter.maydell@linaro.org
Currently we allow board models to specify the initial value of the
Secure VTOR register, using an init-svtor property on the TYPE_ARMV7M
object which is plumbed through to the CPU. Allow board models to
also specify the initial value of the Non-secure VTOR via a similar
init-nsvtor property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210520152840.24453-10-peter.maydell@linaro.org
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Per the kconfig.rst:
A device should be listed [...] ``imply`` if (depending on
the QEMU command line) the board may or may not be started
without it.
This is the case with the NVDIMM device, so use the 'imply'
weak reverse dependency to select the symbol.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210511155354.3069141-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SSE-300 has an ITCM at 0x0000_0000 and a DTCM at 0x2000_0000.
Currently we model these in the AN547 board, but this is conceptually
wrong, because they are a part of the SSE-300 itself. Move the
modelling of the TCMs out of mps2-tz.c into sse300.c.
This has no guest-visible effects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-7-peter.maydell@linaro.org
Currently we model the ITCM in the AN547's RAMInfo list. This is incorrect
because this RAM is really a part of the SSE-300. We can't just delete
it from the RAMInfo list, though, because this would make boot_ram_size()
assert because it wouldn't be able to find an entry in the list covering
guest address 0.
Allow a board to specify a boot RAM size manually if it doesn't have
any RAM itself at address 0 and is relying on the SSE for that, and
set the correct value for the AN547. The other boards can continue
to use the "look it up from the RAMInfo list" logic.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-6-peter.maydell@linaro.org
Convert armsse_realize() to use ERRP_GUARD(), following
the rules in include/qapi/error.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-5-peter.maydell@linaro.org
The SSE-300 was not correctly modelling its internal SRAMs:
* the SRAM address width default is 18
* the SRAM is mapped at 0x2100_0000, not 0x2000_0000 like
the SSE-200 and IoTKit
The default address width is no longer guest-visible since
our only SSE-300 board sets it explicitly to a non-default
value, but following the hardware's default will help for
any future boards we need to model.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-4-peter.maydell@linaro.org
The AN547 sets the SRAM_ADDR_WIDTH for the SSE-300 to 21;
since this is not the default value for the SSE-300, model this
in mps2-tz.c as a per-board value.
Reported-by: Devaraj Ranganna <devaraj.ranganna@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-3-peter.maydell@linaro.org
The SRAM at 0x2000_0000 is part of the SSE-200 itself, and we model
it that way in hw/arm/armsse.c (along with the associated MPCs). We
incorrectly also added an entry to the RAMInfo array for the AN524 in
hw/arm/mps2-tz.c, which was pointless because the CPU would never see
it. Delete it.
The bug had no guest-visible effect because devices in the SSE-200
take priority over those in the board model (armsse.c maps
s->board_memory at priority -2).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510190844.17799-2-peter.maydell@linaro.org
6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
failed to completely fix misalignment issues with range
invalidation. For instance invalidations patterns like "invalidate 32
4kB pages starting from 0xff395000 are not correctly handled" due
to the fact the previous fix only made sure the number of invalidated
pages were a power of 2 but did not properly handle the start
address was not aligned with the range. This can be noticed when
boothing a fedora 33 with protected virtio-blk-pci.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Fixes: 6d9cd115b9 ("hw/arm/smmuv3: Enforce invalidation on a power of two range")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmCeiMEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpqsIH/A49Av5Bv8huL75lf9GzCx3E1a/z2W9Fphik
OcQ1ahR+7CRDARub+vTG40MBmZBVefIWjLAj3BwBWzFGPX0DZq0zeI102VzlEVKY
OeUx8ixuiKOSLcS+QxE7ZXIBL2Pn7l+MFUi4nLMYKti7c/kola7zlB57qsmXh+VD
AOQ7Utj6NWoi6QocWJsMSCyHCh3Fk9QzcStLlr6/MkSJa1zqv8l22+8oWH07Fk2M
wZfhrm9k094on28iSejsFYL5e4ROeXUajbOdfyMIxWvAB7boC9Jxk/e0oAbuSB4y
2f71Gfk3mU6irS7PvrxcKbk6BVD2zxM2WumOchZJgxFAujDO6yg=
=fvkT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: bugfixes, improvements
Fixes all over the place. Faster boot for virtio. ioeventfd support for
mmio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 14 May 2021 15:27:13 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
Fix build with 64 bits time_t
vhost-vdpa: Make vhost_vdpa_get_device_id() static
hw/virtio: enable ioeventfd configuring for mmio
hw/smbios: support for type 41 (onboard devices extended information)
checkpatch: Fix use of uninitialized value
virtio-scsi: Configure all host notifiers in a single MR transaction
virtio-scsi: Set host notifiers and callbacks separately
virtio-blk: Configure all host notifiers in a single MR transaction
virtio-blk: Fix rollback path in virtio_blk_data_plane_start()
pc-dimm: remove unnecessary get_vmstate_memory_region() method
amd_iommu: fix wrong MMIO operations
virtio-net: Constify VirtIOFeature feature_sizes[]
virtio-blk: Constify VirtIOFeature feature_sizes[]
hw/virtio: Pass virtio_feature_get_config_size() a const argument
x86: acpi: use offset instead of pointer when using build_header()
amd_iommu: Fix pte_override_page_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/arm/virt.c
Type 41 defines the attributes of devices that are onboard. The
original intent was to imply the BIOS had some level of control over
the enablement of the associated devices.
If network devices are present in this table, by default, udev will
name the corresponding interfaces enoX, X being the instance number.
Without such information, udev will fallback to using the PCI ID and
this usually gives ens3 or ens4. This can be a bit annoying as the
name of the network card may depend on the order of options and may
change if a new PCI device is added earlier on the commande line.
Being able to provide SMBIOS type 41 entry ensure the name of the
interface won't change and helps the user guess the right name without
booting a first time.
This can be invoked with:
$QEMU -netdev user,id=internet
-device virtio-net-pci,mac=50:54:00:00:00:42,netdev=internet,id=internet-dev \
-smbios type=41,designation='Onboard LAN',instance=1,kind=ethernet,pcidev=internet-dev
The PCI segment is assumed to be 0. This should hold true for most
cases.
$ dmidecode -t 41
# dmidecode 3.3
Getting SMBIOS data from sysfs.
SMBIOS 2.8 present.
Handle 0x2900, DMI type 41, 11 bytes
Onboard Device
Reference Designation: Onboard LAN
Type: Ethernet
Status: Enabled
Type Instance: 1
Bus Address: 0000:00:09.0
$ ip -brief a
lo UNKNOWN 127.0.0.1/8 ::1/128
eno1 UP 10.0.2.14/24 fec0::5254:ff:fe00:42/64 fe80::5254:ff:fe00:42/64
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Message-Id: <20210401171138.62970-1-vincent@bernat.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit dfc388797c ("hw/arm: xlnx: Set all boards' GEM 'phy-addr'
property value to 23") configured the PHY address for xilinx-zynq-a9
to 23. When trying to boot xilinx-zynq-a9 with zynq-zc702.dtb or
zynq-zc706.dtb, this results in the following error message when
trying to use the Ethernet interface.
macb e000b000.ethernet eth0: Could not attach PHY (-19)
The devicetree files for ZC702 and ZC706 configure PHY address 7. The
documentation for the ZC702 and ZC706 evaluation boards suggest that the
PHY address is 7, not 23. Other boards use PHY address 0, 1, 3, or 7.
I was unable to find a documentation or a devicetree file suggesting
or using PHY address 23. The Ethernet interface starts working with
zynq-zc702.dtb and zynq-zc706.dtb when setting the PHY address to 7,
so let's use it.
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210504124140.1100346-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AN524 FPGA image supports two memory maps, which differ in where
the QSPI and BRAM are. In the default map, the BRAM is at
0x0000_0000, and the QSPI at 0x2800_0000. In the second map, they
are the other way around.
In hardware, the initial mapping can be selected by the user by
writing either "REMAP: BRAM" (the default) or "REMAP: QSPI" in the
board configuration file. The board config file is acted on by the
"Motherboard Configuration Controller", which is an entirely separate
microcontroller on the dev board but outside the FPGA.
The guest can also dynamically change the mapping via the SCC
CFG_REG0 register.
Implement this functionality for QEMU, using a machine property
"remap" with valid values "BRAM" and "QSPI" to allow the user to set
the initial mapping, in the same way they can on the FPGA, and
wiring up the bit from the SCC register to also switch the mapping.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-4-peter.maydell@linaro.org
The i.MX25 PDK board has 2 banks for SDRAM, each can
address up to 256 MiB. So the total RAM usable for this
board is 512M. When we ask for more we get a misleading
error message:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: Invalid RAM size, should be 128 MiB
Update the error message to better match the reality:
$ qemu-system-arm -M imx25-pdk -m 513M
qemu-system-arm: RAM size more than 512 MiB is not supported
Fixes: bf350daae0 ("arm/imx25_pdk: drop RAM size fixup")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20210407225608.1882855-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
-----BEGIN PGP SIGNATURE-----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=N5Us
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210503' into staging
Aspeed patches :
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
# gpg: Signature made Mon 03 May 2021 06:23:36 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210503:
aspeed: Add support for the quanta-q7l1-bmc board
hw/block: m25p80: Add support for mt25ql02g and mt25qu02g
aspeed: Add support for the rainier-bmc board
aspeed: Deprecate the swift-bmc machine
tests/qtest: Rename m25p80 test in aspeed_smc test
aspeed/smc: Add extra controls to request DMA
aspeed/smc: Add a 'features' attribute to the object class
hw/misc/aspeed_xdma: Add AST2600 support
tests/acceptance: Test ast2600 machine
tests/acceptance: Test ast2400 and ast2500 machines
tests/qtest: Add test for Aspeed HACE
aspeed: Integrate HACE
hw: Model ASPEED's Hash and Crypto Engine
hw/arm/aspeed: Do not sysbus-map mmio flash region directly, use alias
aspeed/i2c: Rename DMA address space
aspeed/i2c: Fix DMA address mask
aspeed/smc: Remove unused "sdram-base" property
aspeed/smc: Use the RAM memory region for DMAs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/sysbus.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210327082804.2259480-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Intel XScale PXA chipsets provide a PCMCIA controller,
which expose a PCMCIA bus. Express this dependency using
the Kconfig 'select' expression.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210424222057.3434459-2-f4bug@amsat.org>
[lv: remove "(IDE)"]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Quanta-Q71l BMC board is a board supported by OpenBMC.
Tested: Booted quanta-q71l firmware.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210416162426.3217033-1-venture@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Rainier BMC board is a board for the middle range POWER10 IBM systems.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-19-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The SWIFT machine never came out of the lab and we already have enough
AST2500 based OpenPower machines.
Cc: Adriana Kobylak <anoo@us.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When we introduced support for the AST2600 SoC, the XDMA controller
was forgotten. It went unnoticed because it's not used under emulation.
But the register layout being different, the reset procedure is bogus
and this breaks kexec.
Add a AspeedXDMAClass to take into account the register differences.
Cc: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Message-Id: <20210407171637.777743-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the hash and crypto engine model to the Aspeed socs.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210409000253.1475587-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instead of passing the memory address space region, simply use the RAM
memory region instead. This simplifies RAM accesses.
This patch breaks migration compatibility.
Fixes: c4e1f0b483 ("aspeed/smc: Add support for DMAs")
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The driver can query some bits in SMMUv3 IDR5 to learn which
translation granules are supported. Arm recommends that SMMUv3
implementations support at least 4K and 64K granules. But in
the vSMMUv3, there seems to be no reason not to support 16K
translation granule. In addition, if 16K is not supported,
vSVA will failed to be enabled in the future for 16K guest
kernel. So it'd better to support it.
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-300 has a Cortex-M55 (which was the whole reason for us
modelling it), but we forgot to actually update the code to let it
have a different CPU type from the IoTKit and SSE-200. Add CPU type
as a field for ARMSSEInfo instead of hardcoding it to always use a
Cortex-M33.
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416104010.13228-1-peter.maydell@linaro.org
SSE-300 currently shares the SSE-200 Property array. This is
bad principally because the default values of the CPU0_FPU
and CPU0_DSP properties disable the FPU and DSP on the CPU.
That is correct for the SSE-200 but not the SSE-300.
Give the SSE-300 its own Property array with the correct
SSE-300 specific settings:
* SSE-300 has only one CPU, so no CPU1* properties
* SSE-300 CPU has FPU and DSP
Buglink: https://bugs.launchpad.net/qemu/+bug/1923861
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210415182353.8173-1-peter.maydell@linaro.org
Each board in mps2-tz.c specifies a RAMInfo[] array providing
information about each RAM in the board. The .mpc field of the
RAMInfo struct specifies which MPC, if any, the RAM is attached to.
We already assert if the array doesn't have any entry for an MPC, but
we don't diagnose the error of using the same MPC number twice (which
is quite easy to do by accident if copy-and-pasting structure
entries).
Enhance find_raminfo_for_mpc() so that it detects multiple entries
for the MPC as well as missing entries.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-3-peter.maydell@linaro.org
The AN524 has three MPCs: one for the BRAM, one for the QSPI flash,
and one for the DDR. We incorrectly set the .mpc field in the
RAMInfo struct for the SRAM block to 1, giving it the same MPC we are
using for the QSPI. The effect of this was that the QSPI didn't get
mapped into the system address space at all, via an MPC or otherwise,
and guest programs which tried to read from the QSPI would get a bus
error. Correct the SRAM RAMInfo to indicate that it does not have an
associated MPC.
Fixes: 25ff112a8c ("hw/arm/mps2-tz: Add new mps3-an524 board")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210409150527.15053-2-peter.maydell@linaro.org
In emulation of the CFGI_STE_RANGE command, we now take StreamID as the
start of the invalidation range, regardless of whatever the Range is,
whilst the spec clearly states that
- "Invalidation is performed for an *aligned* range of 2^(Range+1)
StreamIDs."
- "The bottom Range+1 bits of the StreamID parameter are IGNORED,
aligning the range to its size."
Take CFGI_ALL (where Range == 31) as an example, if there are some random
bits in the StreamID field, we'll fail to perform the full invalidation but
get a strange range (e.g., SMMUSIDRange={.start=1, .end=0}) instead. Rework
the emulation a bit to get rid of the discrepancy with the spec.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402100449.528-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV values in SMMUv3 IORT node are not correct as they don't match
the SMMUIrq enumeration, which describes the IRQ<->PIN mapping used by
our emulated vSMMU.
Fixes: a703b4f6c1 ("hw/arm/virt-acpi-build: Add smmuv3 node in IORT table")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210402084731.93-1-yuzenghui@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine device plug callback currently calls
platform_bus_link_device() for any sysbus device. This is overly
broad, because platform_bus_link_device() will unconditionally grab
the IRQs and MMIOs of the device it is passed, whether it was
intended for the platform bus or not. Restrict hotpluggability of
sysbus devices to only those devices on the dynamic sysbus
allowlist.
We were mostly getting away with this because the board creates the
platform bus as the last device it creates, and so the hotplug
callback did not do anything for all the sysbus devices created by
the board itself. However if the user plugged in a device which
itself uses a sysbus device internally we would have mishandled this
and probably asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-4-peter.maydell@linaro.org
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They were introduced in commit 9bde7f0674 ("hw/arm/smmuv3: Implement
translate callback") but never actually used. Drop them.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325142702.790-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine already checks KVM_CAP_ARM_VM_IPA_SIZE to get the
upper bound of the IPA size. If that bound is lower than the highest
possible GPA for the machine, then QEMU will error out. However, the
IPA is set to 40 when the highest GPA is less than or equal to 40,
even when KVM may support an IPA limit as low as 32. This means KVM
may fail the VM creation unnecessarily. Additionally, 40 is selected
with the value 0, which means use the default, and that gets around
a check in some versions of KVM, causing a difficult to debug fail.
Always use the IPA size that corresponds to the highest possible GPA,
unless it's lower than 32, in which case use 32. Also, we must still
use 0 when KVM only supports the legacy fixed 40 bit IPA.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Message-id: 20210310135218.255205-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all sid printouts to sid=0x%x.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the whole SID range (32b) is invalidated (SMMU_CMD_CFGI_ALL),
@end overflows and we fail to handle the command properly.
Once this gets fixed, the current code really is awkward in the
sense it loops over the whole range instead of removing the
currently cached configs through a hash table lookup.
Fix both the overflow and the lookup.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210309102742.30442-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, the driver can invalidate a number of pages that is
not a power of 2. However IOTLB unmap notifications and internal
IOTLB invalidations work with masks leading to erroneous
invalidations.
In case the range is not a power of 2, split invalidations into
power of 2 invalidations.
When looking for a single page entry in the vSMMU internal IOTLB,
let's make sure that if the entry is not found using a
g_hash_table_remove() we iterate over all the entries to find a
potential range that overlaps it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the asid is not set, do not attempt to locate the key directly
as all inserted keys have a valid asid.
Use g_hash_table_foreach_remove instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-5-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
