Soren S. Jorvang <soren@t.dk>, with a lower match level.
Display the other accented characters which are not present in the IBM
character set by their non-accented equivalents, with an even lower
match level.
* Macroize hardware and software descriptor access (much easier to read).
* Simplify and optimize the transmit loop a bit, and use IFF_OACTIVE as
appropriate.
* Fix a potential race condition in the transmit loop. This change has
made the driver significantly more stable (almost completely eliminated
the "device timeout" errors that have plagued this driver).
* Implement transmit interrupt pacing.
* Add missing bus_dmamap_sync() calls (on transmit and receive descriptors
and fraglists). (Draining the write buffer when accessing these structures
may have also contributed to the increased stability of this driver on
the Alpha.)
Use fast memory timing NVRAM parameter. Clean up and fix establishment
of default target parameters. Don't use NVRAM if are flagged as not to
do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC
mode but disabled disconnect/reconnect and wide!!). Fix delays after
resets. BUS resets not done in isp_init anymore- relegated to OS
specific outer layers. Fix a buglet where you can get in a loop for
a NULL xs in the completion list in isp_intr. Add in some defines that
can disable fast posting. Add in code for Loop Up/Loop Down events that
call into the outer layers as to what to do.
define. Add a new config flag param (ISP_CFG_NONVRAM) whose intent it is
to cause NVRAM to be ignored. Add ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP
isp_async enums.
(we get LOOP DOWN events, and we'll hang on that at this time).
Add other isp_async cases- ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP. DOWN
will cause internal queuing until UP, whereupon a timeout will fire up
any pending xfers. It doesn't really keep commands from getting destroyed
by loop down events, but at least minimizes the damage. This was much
easier to implement with CAM.
the disk is ready to transfer data, and in ATA-5 the DSC has been obsoleted.
So only wait for DRQ to transfer data. This can be made conditional on the
ATA version if it's proven to break with some drives (worked with all the
drives I have access to).
While I'm there correct a few typos.
* Move the printf() delay to just after the printf(), where it actually makes
sense.
* Use zstty_stint() and zstty_softint() from zsparam(), to force an immediate
update of the carrier and flow control status. Abuse this in the attach and
open functions to defer all of that work. This insures that we don't lose
any status updates.
* Don't screw with register 1 when closing the console.
* Fix bugs in TIOCM??? (stay semicolon, clearing DTR while transmitting).
* Add comments in a couple of places.
the startup code. Implement a call to outer framework function so that
asynchronous events can be handled (e.g., speed negotiation, target mode).
Roll internal release tags.
Thanks to Scott for pointing this out to me (I got his mail and figured out
this change before seeing the discussion on tech-kern) and to Charles for
the initial explanation.
In wdc_probe_caps() add code to guess the ATA revision supported (if
ATA4 if Ultra-DMA, ATA2 if PIO mode > 2). We can't rely on param.atap_ata_major
here, at last one Ultra-DMA drive claims to support only ATA-3.
Use the ATA version in ata_perror(), and to try a flush cache command
in a shutdown hook for IDE drives.
calls
-support use of 2 fonts simultanously; this costs the ability to
"highlight", ie to use the upper 8 colours
-define screen types "80x25bf" and "80x50bf" which use this ability
-add conditional code to deal with the weird mapping of pcvt's
supplemental fonts
reported by Matthias Scheler <tron@lyssa.owl.de> in PR kern/6772.
- After receiving, check whether the receive DMA pointer became 0
what obviously happens if the list runs out of entries. Simply reinit
in this case. This fixes receive lockups after DDB use observed
by myself.
Unstall the receive engine if the ELINK_UPPKTSTATUS indicates that it
was stalled. (Don't know when this might happen. FreeBSD does so.)
+ Enable FIFO bursts, but also detect bogus 1040A with busted FIFO.
+ Use new MEMZERO crossplatform define.
+ Handle RQCS_QUEUE_FULL status case and let upper layer parse SCSI ststus
byte if nonzero (should be 0x28- Queue Full status)
+ Fold ISP_NVRAM_FIFO_THRESHOLD_128 into isp_fifo_threshold tag.
for FC HB based upon a SCCLUN define (15 for normal- 255 out of a possible
65535 for SCCLUN). Propagate loopid as adapter_target.
Roll minor platform version. Roll core version number.
Update mailbox definitions with cleaner target mode structure definitions.
Clean up some ENDIAN stuff. Correct botched ISP2100_NVRAM_HARDLOOPID offset.
- keep the modes supported by the drive in struct ata_drive_datas (will be
later used for downgrading the DMA/PIO mode on error)
- use config flags to force/disable PIO/DMA/UDMA modes
- For the CMD PCI0643/6 setup DMA mode to DMA Read multiple.
- When doing a first open, don't enable receive & status interupts before
the MD layer has had a chance to set things up.
- Enable logic to only enable DCD/CTS interupts if we are looking for/
expecting interupts on those pins. Disable otherwise.
- in zs_param, only pass up the state of ZSRR0_DCD if we have enabled
interupts on that pin.
Henry Hotz (<hotz@jpl.nasa.gov>) and Greg walsh <gwalsh@artec.com> have
tried these changes to get certain printers from hanging at boot. They
work in a 1.3.2 kernel for Greg.
an array of fixed-sized channel_softc elements. This way IDE controllers
which more than 1 channel (pciide) can extend the channel data easily
for private needs.
To avoid the double dereference at runtime, change the argument of
wdcstart() to the channel data pointer instead of the array index.
- Deactivate the card on removal and queue a REMOVAL event for the socket's
event thread to finish the detach.
- Queue an INSERTION event for the socket's event thread on insertion.
Implement a few missing infrastructure pieces to support this.
Hot swapping of PCMCIA cards now "works". (Not quite; things like network
devices need changes for their respestive subsystems. These changes are
coming soon...)
if the chip is reset while transmitting.
XXX
This occurs at boot time because the SIOCADDMULTI always resets the interface
when adding the `all hosts groups' -- usually while the ARP packet is being
transmitted. All drivers should be fixed to not reset the interface when
changing the multicast filter, if possible.
we can't use up all of the remaining sc->txslot[chan].bfree free
bytes) because that would cause the circular buffer read pointer
to become equal to the write pointer, thus signaling 'empty buffer'
to the hardware and stopping the transmitter. spotted and fixed
by Kenjiro Cho <kjc@csl.sony.co.jp>
in the printing of DMA mode (piix3/4 only)
others: set the debug_mask to 0, so that debug messages are turned off by
default but can be easily turned on.
Reset drive_flags to 0 for unconfigured devices, so that they are ignored
later. For configured devices, reset state to 0 after probe/attach.
struct scsipi_adapter; they were not used.
Add a scsipi_ioctl entry point to struct scsipi_adapter. This will be
used to issue ioctl commands to the host adapters.
Inspired by PR #6090, from Matt Jacob.
This bus space tag and handle is used for 32 bit data transfers i.e.
when WDC_CAPABILITY_DATA32 is enabled as the 32 bit data register may
not be part of the standard drive registers.
a slightly different fibre startup (print ALPA now too). Change
the way that return values from dma setup is done. Make debug messages
out of some queue overflow situations. Turn PORT LOGGED OUT into
Selection Timeout equivlaent. On isp_restart actions don't blow off
the commands with HBA_BOTCH (XS_DRIVER_STUFFUP) - set them with HBA_BUSRESET
(which is defined as XS_DRIVER_STUFFUP until someone decides whether
the suggested change to the midlayer NetBSD is worthy of inclusion).
use PIO (or equivalent) code to do asynchronous transfers: In
ncr5380_scsi_cmd(), test to see if the request has been completed after
the call to ncr5380_sched(), and return COMPLETE if so. This avoids
going into an infinite loop in scsipi_execute_xs() while waiting for an
interrupt to trigger completion of the transfer... which, of course,
never happens, since it's already done.
- machine independent chip driver, in dev/ic/smc90cx6.c/...reg.h,...var.h,
using bus_space methods
- ZBUS frontend in arch/amiga/dev/if_bah_zbus.c
- added IPL_SOFTNET to arch/amiga/include/intr.h, for this
Implementing the ISA bus frontend is left as an exercise to the reader.
in epsetmedia() if full-duplex is selected (new feature on these cards!)
On MII Boomerangs, set the full-duplex bit in MAC CONTROL in the statchg
callback from the MII layer. Should fix full-duplex on these cards.
* Improve the midisyn layer a little.
* Add a driver for the Yamaha OPL[23] FM synths.
The opl driver is not finished yet; it sounds pretty awful.
For some strange reason I cannot get any FM sound from my SB64 cards,
but a regular SB16 works fine.
No DMA is wired up, it has a shared memory interface, and a FIFO buffer
which can be used to speed up PIO transfers. (The latter two are
PCMCIA-specific speed hacks to deal hide the performance lossage from
using a PCMCIA->PCI bridge internally.)
the 3Com 3c905-TX and 3c905-T4. Fix handling of the MII on the
3c595-MII and 3c597-MII (can't talk to the PHYs on these cards; just
use "manual" for the external MII port).
Fixes kern/4782 (Chris Demetriou).
The attach routine calls zsparam if we're setting up the console, and
zsparam needs this field to tell which zstty to set up. Otherwise, we
set up zstty0 even if it's not the console!
a "fast scroll" by setting the display start in memory.
(Only implemented for "scroll up" because this is more used. "scroll down"
is easy to add.)
This moves the semantics of "copyrows" to something like "moverows";
the contents of the new visible lines at the bottom is undefined.
The emulations can live without the original "copy" semantics.
clock source. Now, when my EtherPower II locks up, it eventually recovers!
(Geez, I'd like to know why it does this, and only apparently in 10mb/s mode).
tty structures, and on some machines (namely the DraCo internal lpt, and some
multi-i/o boards for Amigas and DraCos), tying spltty to the pretty high printer
interupt level would hurt serial performance.
On all affected ports but Amiga, spllpt() has been defined in machine/intr.h
to be spltty(), thus preserving old behaviour. Portmasters are encouraged to
change is, if they feel something else is better (e.g., one of its own were
possible).
us to call isp_reset/isp_init internally with impunity.
Rename isp_phoenix to isp_restart and make it global. Clean it up a tad.
If we get an ASYNC_SYSTEM_ERROR code in isp_intr, call isp_restart and
return- the f/w is toasted at this point (usually), so we have to bring
things back to a known state.
In isp_mboxcmd, when we don't see the HOST_INT bit go clear, try and
find out if the isp is trying to tell us something and try again. This
may avoid a potential deadlock where the previous mailbox command hasn't
been cleared by the ISP.
In isp_init don't try and get device parameters if we already have them-
this typically doesn't work if we're in the middle of an isp_restart.
There is one change of note- build a list of completing commands in
ispintr and then say you're done- this avoids some re-entrancy issues
that had surfaced.
as with user-land programs, include files are installed by each directory
in the tree that has includes to install. (This allows more flexibility
as to what gets installed, makes 'partial installs' easier, and gives us
more options as to which machines' includes get installed at any given
time.) The old SYS_INCLUDES={symlinks,copies} behaviours are _both_
still supported, though at least one bug in the 'symlinks' case is
fixed by this change. Include files can't be build before installation,
so directories that have includes as targets (e.g. dev/pci) have to move
those targets into a different Makefile.
used in the SMC EtherPower II.
Media control isn't yet supported, due to some MII infrastructure
problems which I hope to address soon. This isn't a huge deal, since
the PHY defaults to auto-negotiate mode.
Also, the device just programs the multicast hash table to accept all
multicast, to avoid a hardware bug that causes the multicast address
filter to lose in 10Mb/s mode. This bug will be fixed in a more sane
way once the media control issues are dealt with.
The graphics device driver passes a "default attribute" for normal text
output to the wscons framework. If the emulation module needs more
attributes (for different "renditions") it can allocate them via a
callback.
For now, only the "sun" emulation makes use of it.
it implemented under the label `shortcut:' and only use it in these
cases: (1) after successful re-relection, (2) after receiving command-complete
status, and (3) during message-in handshake.
for front-ends to override the allocation to avoid alignment
handling in their DMA engines. Note that that ncr53c9x_msgout()
can request a 1 byte DMA transfer that would be difficult to break up.
Cute buglet: you can end up with zero CCBs if there were no targets
seen by the adapter. Always leave a minimum so the adapter can
finish attaching- it may be there w/o targets for a reason.
the capacity based on the c/h/s numbers. In fact, don't use the c/h/s
numbers for much of anything.
For ATA-4 drives or later, always use LBA mode, since it's now required.
Collectively, this allows >8GB disks (like the 12GB Bigfoot) to work.
Compute the disk block addr at command queing time rather than exec time.
This fix a bug which could lead to data corruption on disk: when a command
was reexecuted after an error condition (from wdcunwedge), the partition
offset was re-added to the block addr, leading to a transfert at the wrong
disk block.
This should fix the problem reported by some laptop's users, where the
first disk read after a suspend/resume returned garbage.
to compile. I made the changes that seemed to make sense tracking the
shift from TS_WOPEN to tp->t_wopen- but they may be wrong. I wasn't
subscribed to tech-kern so I missed the discussion, and C. Hannum
was not particularly enlightening. Sorry if this isn't quite right.
two SCC channels, and can get stuck in an infinite loop. This change
stops after flushing 4 bytes. Might need upping to 8 bytes if we support
85230 ESCC's.
Idea bounced off of scottr & gwr
- In the console getc routine, block until a character becomes ready
(no, really, we mean it). This routine should _never_ time out.
- In the console putc routine, if the UART has trouble, do NOT proceed
to print a diagnostic message, which would recursively invoke the
console putc routine ad nauseum.
UVM was written by chuck cranor <chuck@maria.wustl.edu>, with some
minor portions derived from the old Mach code. i provided some help
getting swap and paging working, and other bug fixes/ideas. chuck
silvers <chuq@chuq.com> also provided some other fixes.
this is the rest of the MI portion changes.
this will be KNF'd shortly. :-)
the "stream" busification functions.
In the architecture as the BeBox(CPU is big endian, have ISA bus),
These methods would be used where "raw" data needs to {read,write,set}
unchanged.
Add #ifndef __BUS_SPACE_NEED_STREAM_METHODS (define that on NetBSD/bebox),
if not define __BUS_SPACE_NEED_STREAM_METHODS,
define "stream" busification functions to normal busification functions.
This is useful in the case where an attachment's probe routine
verifies that there is indeed hardware present but something goes
"wrong" in the attach causing the device to be unusable. (Without
keeping track of this, in that case incorrect ports could be
accessed or uninitted pointers could be deferenced on open or at
other times.)
an initiator/target nexus and thus mark the correct queue (if any) a
command is on.
* If a disconnected command times out, just leave it on the nexus queue
and do nothing (for now). I need yet to decide on the strategy to
follow in this case. Note: we used to move the command to the `ready'
queue and then do nothing, which is worse.
the target still is in MSG OUT phase. We still send a message (a NO_OP)
in this case and the chip will remove ATN at the appropriate time.
Using the RSTATN command here induces a "illegal command" in some
chip revisions.
This situation only occurs if the target rejects a previous (multi-byte)
message early (by switching to MESSAGE IN and sending a MESSAGE REJECT)
before the chip has completed the entire MSG OUT transfer. ATN will
remain asserted, and the target returns to MESSAGE OUT phase.
* Account for the events above when reporting "DMA not completed"
diagnostic messages.
* Stream-line the selection code a bit, and make the DMA setup code
more like the MSG OUT & DATA XFER setup.
* Fix bug in wdc that would overflow ATAPI transfer length.
* Improve wdc probe code so that 'wdc' is probed in if present
even if there are no drives attached, and so that it works
properly even if the only device is an ATAPI slave.
* bus_space-ify.
* split the ISA attachment from the wdc driver, and remove
ISA dependencies from non-ISA files.
* claim that wd and wdc are now machine-independent (probably not
completely true, but mostly so; they at least work on arm32 and
i386).
* Various other minor fixups and cleanups, some of which were pointed
out by Kazuki Sakamoto.
- "out of resource" errors cause receive buffer chain corruption
- resets can confuse the interrupt handler
- multi-cast setup causes receive buffer chain corruption
- shared memory setup incomplete
* Enhance effiency by avoiding unnecessary shared memory access,
improved handling of receive frame & buffer descriptors, and
introducing an `asynchronous' option when issuing 82586 commands.
* Exclusively use offsets relative to the bus handle representing the shared
memory area to formulate accesses to the chip's data-structures. The
front-ends provide glue functions that cater to the chip's endian-
sensitivity, to perform the actual device access (note: single-byte
accesses are done here using `bus_space_{read,write}_1()').
This concludes the transformation into a bus-independent driver module.
* Abolish C structures to access chip data-structures; instead use macros
that take indices and offsets relative to the bus handle representing
the chip's resources.
* Include the old version of this file wholesale, until all drivers
have been updated to use the MI 82586 code.
- allow get/set of enums SUNAUDIO_SOURCE and SUNAUDIO_OUTPUT rather
than returning EINVAL
- add missing SUNAUDIO_MONITOR_CLASS case in query_devinfo
- convert SUNAUDIO_MONITOR case from a MIXER_CLASS to a MIXER_VALUE
like it is supposed to be
- the labels for outputs/record class were swapped: fix it
this patch allows "mixerctl" to work properly on a sparc
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
* Carrier detect (TS_CARR_ON) is based on the actual DCD bit, even if it's
being ignored.
* Set TS_WOPEN early on in zsopen().
* Don't disable interrupts on the console during close if we have DDB.
Inert changes:
* Don't handle ZS_HWFLAG_NO_DCD here; the frontend does it.
* Deprecate `register'.
* Use SET(), CLR(), and ISSET().
More performance changes:
* Rototill receive handling; use a backpressure mechanism to prevent livelock.
* Output silo/ibuf overflow warnings at most once per minute, from a callout.
* When we exhaust the current transmit run, turn off transmit interrupts in
zstty_txint(), so we're fairly sure we don't get another one.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
control any more, and the speed of changing DTR isn't really an issue. Also,
the old code created a bug where zsparam() might have failed to set some
registers.
Change the interface to zs_hwiflow(); just have it use zst_rx_blocked.
Make zs_modem() a tiny bit faster.
Do RTS updates immediately; do not allow them to be held.
Stop output as fast as possible when DCD is deasserted.
Do *not* automatically drop DTR when DCD is deasserted.
Only check for rr0 bits that we care about (DTR and DCD).
Make sure we turn on DTR and/or RTS as appropriate during open.
Rearrange close sequence so the tty is flushed before turning off interrupts.
Deal with `softcar' and the console device by silently asserting CLOCAL and
|HUPCL, as in com driver.
Do *not* fiddle with DTR when changing the line speed.
Make sure we update the tty's carrier status when CLOCAL or MDMBUF is changed.
Only change rr1 when we actually need to turn on or off TIE.
things happen if we are the console.
Restore to the prevoius value (not to hardwired 8N1) because this
could be set by the serial console initialization.
Closed PR kern/4373 (Dave Huang)
in the ISR (from the ISA "ed" driver's generic 8390 probe routine).
Also, add a big comment describing exactly what we're checking when
probing for the dp8390 (also lifted from the ISA "ed" driver).
The RST check should help weed-out non-matches before they get to the
fairly invasive memory check.
should creation/initialization of a mscp fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one mscp what we can grab, and continue to hobble along.
Also, fix the mscp freelist fencepost error, similar to aha.c and bha.c
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
shoud creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Adjust the number of ccbs allocated during initialization.
Every ccb could potentially lock 64k of memory for dma buffers if bounce
buffers are used. Instead of BHA_CCB_MAX ccbs using 2MByte, only
sc_link.openings ccbs per device are allocated. Thus we now use only
256KByte per device present.
(hannken)
Fix a couple of errors in bha_create_ccbs():
- Don't ever let the number of CCBs be creater than BHA_CCB_MAX.
- Fix a fencepost that caused the last CCB allocated to never be put
on the freelist.
(thorpej)
- at end of attach, explicitely select an existing drive. This fixes hangs
some users reported (such as the one reported in port-i386/4247).
- Some atapi cdrom drives (e.g. Nec 24x) don't enables their registers before
a controller reset is issued. The controller probe routine is changed as
follow: issue a controller reset. If fail, test atapi signature on slave.
If fail, wait 5s and retry a reset. If the second reset fail, return(0).
If the first reset succeed, test presence of a master drive:
atapi signature, and if this fail RO/RW registers test. If no master, test
atapi signature on slave. If no slave, return 0.
"A sequence step of 0 after a select with ATN can be a selection
timeout, or it can also indicate the target did not respond with
a message out phase. The latter will occur on very old SCSI
devices which do not respond to the ATN signal and go directly to
the command phase".
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
options RND_COM
in your kernel config file (along with the
pseudo-device rnd
line) to enable this. If results are positive, I will make this enabled
by default.
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
> revision 1.1.2.4
> date: 1997/10/15 01:01:57; author: enami; state: Exp; lines: +10 -8
> Use bus_space_write_1() directly instead of NIC_PUT(), since
> - same io port is accessed by bus_space_read_1() in the same function, and
> - can bypass sc_reg_map[].
The isa attachment code is in isa/lpt_isa.c now, which attaches to the
already created ic/lpt* files.
You don't need to change your config files, but you need to re-"config" if
using lpt at isa.
XXX The "lpt" device definition should be in sys/conf/files instead, but to
my knowledge, there are some ports which have private copies of lpt, and would
choke on that. No need to make people unhappy 7 days before release branching.
pseudo-device rnd # /dev/random and in-kernel generator
in config files.
o Add declaration to all architectures.
o Clean up copyright message in rnd.c, rnd.h, and rndpool.c to include
that this code is derived in part from Ted Tyso's linux code.
[1] add EN_ENIDMAFIX - the byte-aligner on the ENI version of the card
appears to lose under heavy load so avoid using it. see comment
in midway.c for full details.
note that the Adaptec version of the card works properly under
load.
detected by Kenjiro Cho <kjc@csl.sony.co.jp> [confirmed by chuck]
fix by chuck & kjc
[2] update some freebsd specific code [from kjc]
[3] for circular buffers: ensure there is always one free slot so
that we can easily tell the difference between a full and
empty list. re-structure a few loops to reflect this.
fixes a problem with mbufs being free'd while still in DMA,
and makes drive a bit more robust.
detected and fixed by kjc
* support chip clocks != COM_FREQ, by introducing sc_frequency (for the
mainline code) and adding a frequency parameter right after the rate
parameter to comcnattach() and com_kgdb_attach().
- Make com_isa and com_multi initialize sc_frequency to COM_FREQ.
- Make i386/machdep.c and alpha/dec_xxx.c call com*attach() with the freq.
parameter.
* supio_attach_args get two more fields: a sc_ipl and a sc_arg, both ints.
- com_supio uses the first for interupt establishment (all childs will, as
soon as they exist) and the 2nd for sc_frequency.
- drsupio passes sc_ipl alway as 5, and for the "com"s, sc_arg as 16*115200
- hyper will pass sc_ipl as 6, and sc_arg as 16 * 460800
be probed several times. This fixes the "ATAPI CD probed as wd drive" problem.
Thanks to Geoff Wing <mason@primenet.com.au> for testing this on his hardware.
I also made inclusion of LPRINTF() dependent solely on the symbol
LPTDEBUG, initialized lptdebug variable to 0 instead of 1, and
matched arguments to format strings in LPRINTF() calls.
looking what's the autoconfig do on strange harware, and ATAPI_DEBUG2 is
for debuging data transfers (and is really verbose once the machine has booted
from an IDE disk).
(currently only CD-ROM drives on i386). The sys/dev/scsipi system provides 2
busses to which devices can attach (scsibus and atapibus). This needed to
change some include files and structure names in the low level scsi drivers.
at the same time instead by using two different calls. This enables
it to check more easily if the combined mode is all right.
- Improve the error checking in audio.c.
- Add a new audio property, AUDIO_PROP_INDEPENDENT, show if the
play and record settings are independent.
- Fix some buglets in audio.c.
-put all early console / KGDB initialization into 1 exported function
(com_*_attach()) each, dont use global variables anymore
-use the passed tcflag_t for port settings instead of hardwiring 8N1
-at autoconfiguration attach time, decide if the attaching device is
already console / KGDB by comparing bus tag and base addr (cgd's wish)
-export a function "com_is_console()" for use by driver frontends for
this comparision
-delay setting of cn_tab->cn_dev until autoconfiguration attach
to get the minor number right
-delete unused comcnprobe() and comcninit()