It is now unused.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-16-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the P9 Processor, the thread interrupt context registers of a CPU
can be accessed "directly" when by load/store from the CPU or
"indirectly" by the IC through an indirect TIMA page. This requires to
configure first the PC_TCTXT_INDIRx registers.
Today, we rely on the get_tctx() handler to deduce from the CPU PIR
the chip from which the TIMA access is being done. By handling the
TIMA memory ops under the interrupt controller model of each machine,
we can uniformize the TIMA direct and indirect ops under PowerNV. We
can also check that the CPUs have been enabled in the XIVE controller.
This prepares ground for the future versions of XIVE.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA region gives access to the thread interrupt context registers
of a CPU. It is mapped at the same address on all chips and can be
accessed by any CPU of the system. To identify the chip from which the
access is being done, the PowerBUS uses a 'chip' field in the
load/store messages. QEMU does not model these messages, instead, we
extract the chip id from the CPU PIR and do a lookup at the machine
level to fetch the targeted interrupt controller.
Introduce pnv_get_chip() and pnv_xive_tm_get_xive() helpers to clarify
this process in pnv_xive_get_tctx(). The latter will be removed in the
subsequent patches but the same principle will be kept.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE KVM devices now has an attribute to configure the number of
interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9
KVM.
The XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance
to provide a hint to the user.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478679392.67101.7843580591407950866.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICS-on-XIVE KVM devices now has an attribute to configure the number
of interrupt servers. This allows to greatly optimize the usage of the VP
space in the XIVE HW, and thus to start a lot more VMs.
Only set this attribute if available in order to support older POWER9 KVM
and pre-POWER9 XICS KVM devices.
The XICS-on-XIVE KVM device now reports the exhaustion of VPs upon the
connection of the first VCPU. Check that in order to have a chance to
provide a hint to the user.
`
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678846.67101.9660531022460517710.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE and XICS-on-XIVE KVM devices on POWER9 hosts can greatly reduce
their consumption of some scarce HW resources, namely Virtual Presenter
identifiers, if they know the maximum number of vCPUs that may run in the
VM.
Prepare ground for this by passing the value down to xics_kvm_connect()
and kvmppc_xive_connect(). This is purely mechanical, no functional
change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157478678301.67101.2717368060417156338.stgit@bahia.tlslab.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TIMA operations are performed on behalf of the XIVE IVPE sub-engine
(Presenter) on the thread interrupt context registers. The current
operations supported by the model are simple and do not require access
to the controller but more complex operations will need access to the
controller NVT table and to its configuration.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the machines have handlers implementing the XiveFabric and
XivePresenter interfaces, remove xive_presenter_match() and make use
of the 'match_nvt' handler of the machine.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveFabric QOM interface acts as the PowerBUS interface between
the interrupt controller and the system and should be implemented by
the QEMU machine. On HW, the XIVE sub-engine is responsible for the
communication with the other chip is the Common Queue (CQ) bridge
unit.
This interface offers a 'match_nvt' handler to perform the CAM line
matching when looking for a XIVE Presenter with a dispatched NVT.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the TIMA of a CPU needs to be accessed from the indirect page,
the thread id of the target CPU is first stored in the PC_TCTXT_INDIR0
register. This thread id is relative to the chip and not to the system.
Introduce a helper routine to look for a CPU of a given PIR and fix
pnv_xive_get_indirect_tctx() to scan only the threads of the local
chip and not the whole machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
and use this helper to exclude CPUs which are not enabled in the XIVE
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
CPU_FOREACH() loops on all the CPUs of the machine which is incorrect.
Each XIVE Presenter should scan only the HW threads of the chip it
belongs to.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each XIVE Router model, sPAPR and PowerNV, now implements the 'match_nvt'
handler of the XivePresenter QOM interface. This is simply moving code
and taking into account the new API.
To be noted that the xive_router_get_tctx() helper is not used anymore
when doing CAM matching and will be removed later on after other changes.
The XIVE presenter model is still too simple for the PowerNV machine
and the CAM matching algo is not correct on multichip system. Subsequent
patches will introduce more changes to scan all chips of the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the XIVE IVRE sub-engine (XiveRouter) looks for a Notification
Virtual Target (NVT) to notify, it broadcasts a message on the
PowerBUS to find an XIVE IVPE sub-engine (Presenter) with the NVT
dispatched on one of its HW threads, and then forwards the
notification if any response was received.
The current XIVE presenter model is sufficient for the pseries machine
because it has a single interrupt controller device, but the PowerNV
machine can have multiple chips each having its own interrupt
controller. In this case, the XIVE presenter model is too simple and
the CAM line matching should scan all chips of the system.
To start fixing this issue, we first extend the XIVE Router model with
a new XivePresenter QOM interface representing the XIVE IVPE
sub-engine. This interface exposes a 'match_nvt' handler which the
sPAPR and PowerNV XIVE Router models will need to implement to perform
the CAM line matching.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191125065820.927-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A context should be 'valid' when pulled from the thread interrupt
context registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OS CAM line has a special encoding exploited by the HW. Provide
helper routines to hide the details to the TIMA command handlers. This
also clarifies the endianness of different variables : 'qw1w2' is
big-endian and 'cam' is native.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When dumping the END and NVT tables, the error logging is too noisy.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When using the XIVE KVM device, the trigger page is directly accessible
in QEMU. Unlike with XICS, no need to ask KVM to fire the interrupt. A
simple store on the trigger page does the job.
Just call xive_esb_trigger().
This may improve performance of emulated devices that go through
qemu_set_irq(), eg. virtio devices created with ioeventfd=off or
configured by the guest to use LSI interrupts, which aren't really
recommended setups.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157408992731.494439.3405812941731584740.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
pnv_xive_vst_size() tries to compute the size of a VSD table from the
information given by FW. The number of entries of the table are
deduced from the result and the MMIO regions of the ESBs and the END
ESBs are then resized accordingly with the computed value. This
reduces the number of elements that can be addressed by the ESB pages.
The maximum number of elements of a direct table can contain is simply:
Table size / sizeof(XIVE structure)
An indirect table is a one page array of VSDs pointing to subpages
containing XIVE virtual structures and the maximum number of elements
an indirect table can contain :
(PAGE_SIZE / sizeof(vsd)) * (PAGE_SIZE / sizeof(XIVE structure))
which gives us 16M for XiveENDs, 8M for XiveNVTs. That's more than the
associated VC and PC BARS can address.
The result returned by pnv_xive_vst_size() for indirect tables is
incorrect and can not be used to reduce the size of the MMIO region of
a XIVE resource using an indirect table, such as ENDs in skiboot.
Remove pnv_xive_vst_size() and use a simpler form for direct tables
only. Keep the resizing of the MMIO region for direct tables only as
this is still useful for the ESB MMIO window.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When an interrupt can not be presented to a vCPU, because it is not
running on any of the HW treads, the XIVE presenter updates the
Interrupt Pending Buffer register of the associated XIVE NVT
structure. This is only done if backlog is activated in the END but
this is generally the case.
The current code assumes that the fields of the NVT structure is
architected with the same layout of the thread interrupt context
registers. Fix this assumption and define an offset for the IPB
register backup value in the NVT.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191115162436.30548-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICP object has both a pointer and an ICP_PROP_CPU property pointing
to the cpu. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitly sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403284709.409804.16142099083325945141.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICP object has both a pointer and an ICP_PROP_XICS property pointing
to the XICS fabric. Confusing bugs could arise if these ever go out of
sync.
Change the property definition so that it explicitly sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403284152.409804.17114564311521923733.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object has both a pointer and an ICS_PROP_XICS property pointing
to the XICS fabric. Confusing bugs could arise if these ever go out of
sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157403283596.409804.17347207690271971987.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE object has both a pointer and a "chip" property pointing to the
chip object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383336564.165747.10250365296928442882.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The END source object has both a pointer and a "xive" property pointing to
the router object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333784.165747.5298512574054268786.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source object has both a pointer and a "xive" property pointing to the
notifier object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
The property isn't optional : not being able to set the link is a bug
and QEMU should rather abort than exit in this case.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383333227.165747.12901571295951957951.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The TCTX object has both a pointer and a "cpu" property pointing to the
vCPU object. Confusing bugs could arise if these ever go out of sync.
Change the property definition so that it explicitely sets the pointer.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157383332669.165747.2484056603605646820.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
exynos4210_gic_realize() prints the number of cpus into some temporary
buffers, but it only allows 3 bytes space for it. That's plenty:
existing machines will only ever set this value to EXYNOS4210_NCPUS
(2). But the compiler can't always figure that out, so some[*] gcc9
versions emit -Wformat-truncation warnings.
We can fix that by hinting the constraint to the compiler with a
suitably placed assert().
[*] The bizarre thing here, is that I've long gotten these warnings
compiling in a 32-bit x86 container as host - Fedora 30 with
gcc-9.2.1-1.fc30.i686 - but it compiles just fine on my normal
x86_64 host - Fedora 30 with and gcc-9.2.1-1.fc30.x86_64.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: deleted stray blank line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CPU_FOREACH() can race with vCPU hotplug/unplug on sPAPR machines, ie.
we may try to print out info about a vCPU with a NULL presenter pointer.
Check that in order to prevent QEMU from crashing.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192725327.3146912.12047076483178652551.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
When a VCPU gets connected to the XIVE interrupt controller, we add a
const link targetting the CPU object to the TCTX object. Similar links
are added to the ICP object when using the XICS interrupt controller.
As explained in <qom/object.h>:
* The caller must ensure that @target stays alive as long as
* this property exists. In the case @target is a child of @obj,
* this will be the case. Otherwise, the caller is responsible for
* taking a reference.
We're in the latter case for both XICS and XIVE. Add the missing
calls to object_ref() and object_unref().
This doesn't fix any known issue because the life cycle of the TCTX or
ICP happens to be shorter than the one of the CPU or XICS fabric, but
better safe than sorry.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <157192724770.3146912.15400869269097231255.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
These devices implemented their load_state_old() handler 10 years
ago, previous to QEMU v0.12.
Since commit cc425b5ddf removed the pc-0.10 and pc-0.11 machines,
we can drop this code.
Note: the mips_r4k machine started to use the i8254 device just
after QEMU v0.5.0, but the MIPS machine types are not versioned,
so there is no migration compatibility issue removing this handler.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
There are three page size in qemu:
real host page size
host page size
target page size
All of them have dedicate variable to represent. For the last two, we
use the same form in the whole qemu project, while for the first one we
use two forms: qemu_real_host_page_size and getpagesize().
qemu_real_host_page_size is defined to be a replacement of
getpagesize(), so let it serve the role.
[Note] Not fully tested for some arch or device.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Continue setting, but not relying upon, env->hflags.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191023150057.25731-22-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a Virtual Processor is scheduled to run on a HW thread, the
hypervisor pushes its identifier in the OS CAM line. When running with
kernel_irqchip=off, QEMU needs to emulate the same behavior.
Set the OS CAM line when the interrupt presenter of the sPAPR core is
reset. This will also cover the case of hot-plugged CPUs.
This change also has the benefit to remove the use of CPU_FOREACH()
which can be unsafe.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the sPAPR machine and PowerNV machine, the interrupt presenters are
created by a machine handler at the core level and are reset
independently. This is not consistent and it raises issues when it
comes to handle hot-plugged CPUs. In that case, the presenters are not
reset. This is less of an issue in XICS, although a zero MFFR could
be a concern, but in XIVE, the OS CAM line is not set and this breaks
the presenting algorithm. The current code has workarounds which need
a global cleanup.
Extend the sPAPR IRQ backend and the PowerNV Chip class with a new
cpu_intc_reset() handler called by the CPU reset handler and remove
the XiveTCTX reset handler which is now redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The remaining logic in the post_load hook really belongs to the interrupt
controller backends, and just needs to be called on the active controller
(after the active controller is set to the right thing based on the
incoming migration in the generic spapr_irq_post_load() logic).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It turns out that all the logic in the SpaprIrq::reset hooks (and some in
the SpaprIrq::post_load hooks) isn't really related to resetting the irq
backend (that's handled by the backends' own reset routines). Rather its
about getting the backend ready to be the active interrupt controller or
stopping being the active interrupt controller - reset (and post_load) is
just the only time that changes at present.
To make this flow clearer, move the logic into the explicit backend
activate and deactivate hooks.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Both XICS and XIVE have routines to connect and disconnect KVM with
similar but not identical signatures. This adjusts them to match
exactly, which will be useful for further cleanups later.
While we're there, we add an explicit return value to the connect path
to streamline error reporting in the callers. We remove error
reporting the disconnect path. In the XICS case this wasn't used at
all. In the XIVE case the only error case was if the KVM device was
set up, but KVM didn't have the capability to do so which is pretty
obviously impossible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly through
that, rather than dispatching via SpaprIrq with the dual version having
to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
These methods, like cpu_intc_create, really belong to the interrupt
controller, but need to be called on all possible intcs.
Like cpu_intc_create, therefore, make them methods on the intc and
always call it for all existing intcs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method essentially represents code which belongs to the interrupt
controller, but needs to be called on all possible intcs, rather than
just the currently active one. The "dual" version therefore calls
into the xics and xive versions confusingly.
Handle this more directly, by making it instead a method on the intc
backend, and always calling it on every backend that exists.
While we're there, streamline the error reporting a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The SpaprIrq structure is used to represent ths spapr machine's irq
backend. Except that it kind of conflates two concepts: one is the
backend proper - a specific interrupt controller that we might or
might not be using, the other is the irq configuration which covers
the layout of irq space and which interrupt controllers are allowed.
This leads to some pretty confusing code paths for the "dual"
configuration where its hooks redirect to other SpaprIrq structures
depending on the currently active irq controller.
To clean this up, we start by introducing a new
SpaprInterruptController QOM interface to represent strictly an
interrupt controller backend, not counting anything configuration
related. We implement this interface in the XICs and XIVE interrupt
controllers, and in future we'll move relevant methods from SpaprIrq
into it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The trigger data is used for both triggers of a HW source interrupts,
PHB, PSI, and triggers for rerouting interrupts between interrupt
controllers.
When an interrupt is rerouted, the trigger data follows an "END
trigger" format. In that case, the remote IC needs EAS containing an
END index to perform a lookup of an END.
An END trigger, bit0 of word0 set to '1', is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 E=1 |1P--|BLOC| END IDX |
W1 E=1 |M | END DATA |
An EAS is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 |V---|BLOC| END IDX |
W1 |M | END DATA |
The END trigger adds an extra 'PQ' bit, bit1 of word0 set to '1',
signaling that the PQ bits have been checked. That bit is unused in
the initial EAS definition.
When a HW device performs the trigger, the trigger data follows an
"EAS trigger" format because the trigger data in that case contains an
EAS index which the IC needs to look for.
An EAS trigger, bit0 of word0 set to '0', is defined as :
|0123|4567|0123|4567|0123|4567|0123|4567|
W0 E=0 |0P--|---- ---- ---- ---- ---- ---- ----|
W1 E=0 |BLOC| EAS INDEX |
There is also a 'PQ' bit, bit1 of word0 to '1', signaling that the
PQ bits have been checked.
Introduce these new trigger bits and rename the XIVE_SRCNO macros in
XIVE_EAS to reflect better the nature of the data.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191007084102.29776-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some device types of the XICS model are exposed to the QEMU command
line:
$ ppc64-softmmu/qemu-system-ppc64 -device help | grep ic[sp]
name "icp"
name "ics"
name "ics-spapr"
name "pnv-icp", desc "PowerNV ICP"
These are internal devices that shouldn't be instantiable by the
user. By the way, they can't be because their respective realize
functions expect link properties that can't be set from the command
line:
qemu-system-ppc64: -device icp: required link 'xics' not found:
Property '.xics' not found
qemu-system-ppc64: -device ics: required link 'xics' not found:
Property '.xics' not found
qemu-system-ppc64: -device ics-spapr: required link 'xics' not found:
Property '.xics' not found
qemu-system-ppc64: -device pnv-icp: required link 'xics' not found:
Property '.xics' not found
Hide them by setting dc->user_creatable to false in the base class
"icp" and "ics" init functions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157017826724.337875.14822177178282524024.stgit@bahia.lan>
Message-Id: <157045578962.865784.8551555523533955113.stgit@bahia.lan>
[dwg: Folded reason comment into base patch]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some device types of the XIVE model are exposed to the QEMU command
line:
$ ppc64-softmmu/qemu-system-ppc64 -device help | grep xive
name "xive-end-source", desc "XIVE END Source"
name "xive-source", desc "XIVE Interrupt Source"
name "xive-tctx", desc "XIVE Interrupt Thread Context"
These are internal devices that shouldn't be instantiable by the
user. By the way, they can't be because their respective realize
functions expect link properties that can't be set from the command
line:
qemu-system-ppc64: -device xive-source: required link 'xive' not found:
Property '.xive' not found
qemu-system-ppc64: -device xive-end-source: required link 'xive' not found:
Property '.xive' not found
qemu-system-ppc64: -device xive-tctx: required link 'cpu' not found:
Property '.cpu' not found
Hide them by setting dc->user_creatable to false in their respective
class init functions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157017473006.331610.2983143972519884544.stgit@bahia.lan>
Message-Id: <157045578401.865784.6058183726552779559.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded comment update into base patch]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In apic_accept_pic_intr(), reject PIC interruptions if a i8259 PIC has
not been instantiated (isa_pic == NULL).
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Split up PCMachineState and PCMachineClass and derive X86MachineState
and X86MachineClass from them. This allows sharing code with non-PC
x86 machine types.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Various logging improvements as once:
- Use 0x prefix for hex numbers
- Display value written during write accesses
- Move some logs from GUEST_ERROR to UNIMP
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-id: 20190926173428.10713-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Host kernels that expose the KVM_CAP_ARM_IRQ_LINE_LAYOUT_2 capability
allow injection of interrupts along with vcpu ids larger than 255.
Let's encode the vpcu id on 12 bits according to the upgraded KVM_IRQ_LINE
ABI when needed.
Given that we have two callsites that need to assemble
the value for kvm_set_irq(), a new helper routine, kvm_arm_set_irq
is introduced.
Without that patch qemu exits with "kvm_set_irq: Invalid argument"
message.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-id: 20191003154640.22451-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
spapr_xive_irq_claim() returns a bool to indicate if it succeeded.
But most of the callers and one callee use int return values and/or an
Error * with more information instead. In any case, ints are a more
common idiom for success/failure states than bools (one never knows
what sense they'll be in).
So instead change to an int return value to indicate presence of error
+ an Error * to describe the details through that call chain.
It also didn't actually check if the irq was already claimed, which is
one of the primary purposes of the claim path, so do that.
spapr_xive_irq_free() also returned a bool... which no callers checked
and was always true, so just drop it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The irq claim and free paths for both XICS and XIVE check for some
validity conditions. Some of these represent genuine runtime failures,
however others - particularly checking that the basic irq number is in a
sane range - could only fail in the case of bugs in the callin code.
Therefore use assert()s instead of runtime failures for those.
In addition the non backend-specific part of the claim/free paths should
only be used for PAPR external irqs, that is in the range SPAPR_XIRQ_BASE
to the maximum irq number. Put assert()s for that into the top level
dispatchers as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
This method is used to determine the name of the irq backend's node in the
device tree, so that we can find its phandle (after SLOF may have modified
it from the phandle we initially gave it).
But, in the two cases the only difference between the node name is the
presence of a unit address. Searching for a node name without considering
unit address is standard practice for the device tree, and
fdt_subnode_offset() will do exactly that, making this method unecessary.
While we're there, remove the XICS_NODENAME define. The name
"interrupt-controller" is required by PAPR (and IEEE1275), and a bunch of
places assume it already.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
We create a subtype of TYPE_ICS specifically for sPAPR. For now all this
does is move the setup of the PAPR specific hcalls and RTAS calls to
the realize() function for this, rather than requiring the PAPR code to
explicitly call xics_spapr_init(). In future it will have some more
function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
TYPE_ICS_SIMPLE is the only subtype of TYPE_ICS_BASE that's ever
instantiated. The existence of different classes is mostly a hang
over from when we (misguidedly) had separate subtypes for the KVM and
non-KVM version of the device.
There could be some call for an abstract base type for ICS variants
that use a different representation of their state (PowerNV PHB3 might
want this). The current split isn't really in the right place for
that though. If we need this in future, we can re-implement it more
in line with what we actually need.
So, collapse the two classes together into just TYPE_ICS.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently TYPE_XICS_BASE and TYPE_XICS_SIMPLE have their own reset methods,
using the standard technique for having the subtype call the supertype's
methods before doing its own thing.
But TYPE_XICS_SIMPLE is the only subtype of TYPE_XICS_BASE ever
instantiated, so there's no point having the split here. Merge them
together into just an ics_reset() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
There are a number of ics_simple_*() functions that aren't actually
specific to TYPE_XICS_SIMPLE at all, and are equally valid on
TYPE_XICS_BASE. Rename them to ics_*() accordingly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently ics_reject(), ics_resend() and ics_eoi() indirect through
class methods. But there's only one implementation of each method,
the one in TYPE_ICS_SIMPLE. TYPE_ICS_BASE has no implementation, but
it's never instantiated, and has no other subtypes.
So clean up by eliminating the method and just having ics_reject(),
ics_resend() and ics_eoi() contain the logic directly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
When vCPUs are hotplugged, they are added to the QEMU CPU list before
being fully realized. This can crash the XIVE presenter because the
'tctx' pointer is not necessarily initialized when looking for a
matching target.
These vCPUs are not valid targets for the presenter. Skip them.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191001085722.32755-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
A typical pseries VM with 16 vCPUs, one disk, one network adapater
uses less than 100 interrupts but the whole IRQ number space of the
QEMU machine is allocated at reset time and it is 8K wide. This is
wasting a considerable amount of interrupt numbers in the global IRQ
space which has 1M interrupts per socket on a POWER9.
To optimise the HW resources, only request at the KVM level interrupts
which have been claimed by the guest. This will help to increase the
maximum number of VMs per system and also help supporting nested guests
using the XIVE interrupt mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190911133937.2716-3-clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156942766014.1274533.10792048853177121231.stgit@bahia.lan>
[dwg: Folded in fix up from Greg Kurz]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since QEMU v2.10, the KVM acceleration does not work on older kernels
anymore since the code accidentally requires the KVM_CAP_DEVICE_CTRL
capability now - it should have been optional instead.
Instead of fixing the bug, we asked in the ChangeLog of QEMU 2.11 - 3.0
that people should speak up if they still need support of QEMU running
with KVM on older kernels, but seems like nobody really complained.
Thus let's make this official now and turn it into a proper error
message, telling the users to use at least kernel 3.15 now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190913091443.27565-1-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Preparation for collapsing the two byte swaps adjust_endianness and
handle_bswap into the former.
Call memory_region_dispatch_{read|write} with endianness encoded into
the "MemOp op" operand.
This patch does not change any behaviour as
memory_region_dispatch_{read|write} is yet to handle the endianness.
Once it does handle endianness, callers with byte swaps can collapse
them into adjust_endianness.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Message-Id: <8066ab3eb037c0388dfadfe53c5118429dd1de3a.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The memory_region_dispatch_{read|write} operand "unsigned size" is
being converted into a "MemOp op".
Convert interfaces by using no-op size_memop.
After all interfaces are converted, size_memop will be implemented
and the memory_region_dispatch_{read|write} operand "unsigned size"
will be converted into a "MemOp op".
As size_memop is a no-op, this patch does not change any behaviour.
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <21113bae2f54b45176701e0bf595937031368ae6.1566466906.git.tony.nguyen@bt.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
If an IRQ is allocated and not configured, such as a MSI requested by
a PCI driver, it can be saved in its default state and possibly later
on restored using the same state. If not initially MASKED, KVM will
try to find a matching priority/target tuple for the interrupt and
fail to restore the VM because 0/0 is not a valid target.
When allocating a IRQ number, the EAS should be set to a sane default :
VALID and MASKED.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190813164420.9829-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a better output of the XIVE END structures including the
escalation information and extend the PowerNV machine 'info pic'
command with a dump of the END EAS table used for escalations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the 's' bit is set the escalation is said to be 'silent' or
'silent/gather'. In such configuration, the notification sequence is
skipped and only the escalation sequence is performed. This is used to
configure all the EQs of a vCPU to escalate on a single EQ which will
then target the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the 'u' bit is set the escalation is said to be 'unconditional'
which means that the ESe PQ bits are not used. Introduce a
xive_router_end_es_notify() routine to share code with the ESn
notification.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If the XIVE presenter can not find the NVT dispatched on any of the HW
threads, it can not deliver the interrupt. XIVE offers an escalation
mechanism to handle such scenarios and inform the hypervisor that an
action should be taken.
Escalation is configured by setting the 'e' bit and the EAS in word 4
& 5 to let the HW look for the escalation END on which to trigger a
new event.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If backlog is activated ('b' bit) on the END, the pending priority of
a missed event is recorded in the IPB field of the NVT for a later
resend.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a vCPU is not dispatched anymore on a HW thread, the Hypervisor
(KVM on Linux) invalidates the OS interrupt context of a vCPU with
this special command. It returns the OS CAM line value and resets the
VO bit.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190718115420.19919-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Xilinx I/O Module Interrupt Controller is only used by the
MicroBlaze PMU, not by the AArch64 machine.
Move it from the generic ZynqMP object list to the PMU specific.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427141459.19728-3-philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing migration/qemu-file-types.h
triggers a recompile of some 2600 out of 6600 objects (not counting
tests and objects that don't depend on qemu/osdep.h).
The culprit is again hw/hw.h, which supposedly includes it for
convenience.
Include migration/qemu-file-types.h only where it's needed. Touching
it now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The migration sequence of a guest using the XIVE exploitation mode
relies on the fact that the states of all devices are restored before
the machine is. This is not true for hot-plug devices such as CPUs
which state come after the machine. This breaks migration because the
thread interrupt context registers are not correctly set.
Fix migration of hotplugged CPUs by restoring their context in the
'post_load' handler of the XiveTCTX model.
Fixes: 277dd3d771 ("spapr/xive: add migration support for KVM")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190813064853.29310-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Masked entries will not generate interrupt messages, thus do no need to
be routed by KVM. This is a cosmetic cleanup, just avoiding warnings of
the kind
qemu-system-x86_64: vtd_irte_get: detected non-present IRTE (index=0, high=0xff00, low=0x100)
if the masked entry happens to reference a non-present IRTE.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <a84b7e03-f9a8-b577-be27-4d93d1caa1c9@siemens.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The ics_set_kvm_state_one() function is called either to restore the
state of an interrupt source during migration or to set the interrupt
source to a default state during reset.
Since always, ie. 2013, the code only sets the MASKED bit if the 'current
priority' and the 'saved priority' are different. This is likely true
when restoring an interrupt that had been previously masked with the
ibm,int-off RTAS call. However this is always false in the case of
reset since both 'current priority' and 'saved priority' are equal to
0xff, and the MASKED bit is never set.
The legacy KVM XICS device gets away with that because it ends updating
its internal structure the same way, whether the MASKED bit is set or
the priority is 0xff.
The XICS-on-XIVE device for POWER9 is different. It sticks to the KVM
documentation [1] and _really_ relies on the MASKED bit to correctly
set. If not, it will configure the interrupt source in the XIVE HW, even
though the guest hasn't configured the interrupt yet. This disturbs the
complex logic implemented in XICS-on-XIVE and may result in the loss of
subsequent queued events.
Always set the MASKED bit if interrupt is masked as expected by the KVM
XICS-on-XIVE device. This has no impact on the legacy KVM XICS.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/virtual/kvm/devices/xics.txt
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156217454083.559957.7359208229523652842.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdH7FgAAoJEL/70l94x66DdUUH+gLr/ZdjLIdfYy9cjcnevf4E
cJlxdaW9KvUsK2uVgqQ/3b1yF+GCGk10n6n8ZTIbClhs+6NpqEMz5O3FA/Na6FGA
48M2DwJaJ2H9AG/lQBlSBNUZfLsEJ9rWy7DHvNut5XMJFuWGwdtF/jRhUm3KqaRq
vAaOgcQHbzHU9W8r1NJ7l6pnPebeO7S0JQV+82T/ITTz2gEBDUkJ36boO6fedkVQ
jLb9nZyG3CJXHm2WlxGO4hkqbLFzURnCi6imOh2rMdD8BCu1eIVl59tD1lC/A0xv
Pp3xXnv9SgJXsV4/I/N3/nU85ZhGVMPQZXkxaajHPtJJ0rQq7FAG8PJMEj9yPe8=
=poke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Bugfixes.
# gpg: Signature made Fri 05 Jul 2019 21:21:52 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
ioapic: use irq number instead of vector in ioapic_eoi_broadcast
hw/i386: Fix linker error when ISAPC is disabled
Makefile: generate header file with the list of devices enabled
target/i386: kvm: Fix when nested state is needed for migration
minikconf: do not include variables from MINIKCONF_ARGS in config-all-devices.mak
target/i386: fix feature check in hyperv-stub.c
ioapic: clear irq_eoi when updating the ioapic redirect table entry
intel_iommu: Fix unexpected unmaps during global unmap
intel_iommu: Fix incorrect "end" for vtd_address_space_unmap
i386/kvm: Fix build with -m32
checkpatch: do not warn for multiline parenthesized returned value
pc: fix possible NULL pointer dereference in pc_machine_get_device_memory_region_size()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When emulating irqchip in qemu, such as following command:
x86_64-softmmu/qemu-system-x86_64 -m 1024 -smp 4 -hda /home/test/test.img
-machine kernel-irqchip=off --enable-kvm -vnc :0 -device edu -monitor stdio
We will get a crash with following asan output:
(qemu) /home/test/qemu5/qemu/hw/intc/ioapic.c:266:27: runtime error: index 35 out of bounds for type 'int [24]'
=================================================================
==113504==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x61b000003114 at pc 0x5579e3c7a80f bp 0x7fd004bf8c10 sp 0x7fd004bf8c00
WRITE of size 4 at 0x61b000003114 thread T4
#0 0x5579e3c7a80e in ioapic_eoi_broadcast /home/test/qemu5/qemu/hw/intc/ioapic.c:266
#1 0x5579e3c6f480 in apic_eoi /home/test/qemu5/qemu/hw/intc/apic.c:428
#2 0x5579e3c720a7 in apic_mem_write /home/test/qemu5/qemu/hw/intc/apic.c:802
#3 0x5579e3b1e31a in memory_region_write_accessor /home/test/qemu5/qemu/memory.c:503
#4 0x5579e3b1e6a2 in access_with_adjusted_size /home/test/qemu5/qemu/memory.c:569
#5 0x5579e3b28d77 in memory_region_dispatch_write /home/test/qemu5/qemu/memory.c:1497
#6 0x5579e3a1b36b in flatview_write_continue /home/test/qemu5/qemu/exec.c:3323
#7 0x5579e3a1b633 in flatview_write /home/test/qemu5/qemu/exec.c:3362
#8 0x5579e3a1bcb1 in address_space_write /home/test/qemu5/qemu/exec.c:3452
#9 0x5579e3a1bd03 in address_space_rw /home/test/qemu5/qemu/exec.c:3463
#10 0x5579e3b8b979 in kvm_cpu_exec /home/test/qemu5/qemu/accel/kvm/kvm-all.c:2045
#11 0x5579e3ae4499 in qemu_kvm_cpu_thread_fn /home/test/qemu5/qemu/cpus.c:1287
#12 0x5579e4cbdb9f in qemu_thread_start util/qemu-thread-posix.c:502
#13 0x7fd0146376da in start_thread (/lib/x86_64-linux-gnu/libpthread.so.0+0x76da)
#14 0x7fd01436088e in __clone (/lib/x86_64-linux-gnu/libc.so.6+0x12188e
This is because in ioapic_eoi_broadcast function, we uses 'vector' to
index the 's->irq_eoi'. To fix this, we should uses the irq number.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190622002119.126834-1-liq3ea@163.com>
irq_eoi is used to count the number of irq injected during eoi
broadcast. It should be set to 0 when updating the ioapic's redirect
table entry.
Suggested-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190624151635.22494-1-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In v8M, an attempt to return from an exception which is not
active is an illegal exception return. For this purpose,
exceptions which can configurably target either Secure or
NonSecure are not considered to be active if they are
configured for the opposite security state for the one
we're trying to return from (eg attempt to return from
an NS NMI but NMI targets Secure). In the pseudocode this
is handled by IsActiveForState().
Detect this case rather than counting an active exception
possibly of the wrong security state as being sufficient.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190617175317.27557-4-peter.maydell@linaro.org
To prevent execution priority remaining negative if the guest
returns from an NMI or HardFault with a corrupted IPSR, the
v8M interrupt deactivation process forces the HardFault and NMI
to inactive based on the current raw execution priority,
even if the interrupt the guest is trying to deactivate
is something else. In the pseudocode this is done in the
Deactivate() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190617175317.27557-3-peter.maydell@linaro.org
Here's my next pull request for qemu-4.1. I'm not sure if this will
squeak in just before the soft freeze, or just after. I don't think
it really matters - most of this is bugfixes anyway. There's some
cleanups which aren't stictly bugfixes, but which I think are safe
enough improvements to go in the soft freeze. There's no true feature
work.
Unfortunately, I wasn't able to complete a few of my standard battery
of pre-pull tests, due to some failures that appear to also be in
master. I'm hoping that hasn't missed anything important in here.
Highlights are:
* A number of fixe and cleanups for the XIVE implementation
* Cleanups to the XICS interrupt controller to fit better with the new
XIVE code
* Numerous fixes and improvements to TCG handling of ppc vector
instructions
* Remove a number of unnnecessary #ifdef CONFIG_KVM guards
* Fix some errors in the PCI hotplug paths
* Assorted other fixes
-----BEGIN PGP SIGNATURE-----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=QAyU
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190702' into staging
ppc patch queue 2019-07-2
Here's my next pull request for qemu-4.1. I'm not sure if this will
squeak in just before the soft freeze, or just after. I don't think
it really matters - most of this is bugfixes anyway. There's some
cleanups which aren't stictly bugfixes, but which I think are safe
enough improvements to go in the soft freeze. There's no true feature
work.
Unfortunately, I wasn't able to complete a few of my standard battery
of pre-pull tests, due to some failures that appear to also be in
master. I'm hoping that hasn't missed anything important in here.
Highlights are:
* A number of fixe and cleanups for the XIVE implementation
* Cleanups to the XICS interrupt controller to fit better with the new
XIVE code
* Numerous fixes and improvements to TCG handling of ppc vector
instructions
* Remove a number of unnnecessary #ifdef CONFIG_KVM guards
* Fix some errors in the PCI hotplug paths
* Assorted other fixes
# gpg: Signature made Tue 02 Jul 2019 07:07:15 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190702: (49 commits)
spapr/xive: Add proper rollback to kvmppc_xive_connect()
ppc/xive: Fix TM_PULL_POOL_CTX special operation
ppc/pnv: Rework cache watch model of PnvXIVE
ppc/xive: Make the PIPR register readonly
ppc/xive: Force the Physical CAM line value to group mode
spapr/xive: simplify spapr_irq_init_device() to remove the emulated init
spapr/xive: rework the mapping the KVM memory regions
spapr_pci: Unregister listeners before destroying the IOMMU address space
target/ppc: improve VSX_FMADD with new GEN_VSX_HELPER_VSX_MADD macro
target/ppc: decode target register in VSX_EXTRACT_INSERT at translation time
target/ppc: decode target register in VSX_VECTOR_LOAD_STORE_LENGTH at translation time
target/ppc: introduce GEN_VSX_HELPER_R2_AB macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_R2 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_R3 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X1 macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X2_AB macro to fpu_helper.c
target/ppc: introduce GEN_VSX_HELPER_X2 macro to fpu_helper.c
target/ppc: introduce separate generator and helper for xscvqpdp
target/ppc: introduce GEN_VSX_HELPER_X3 macro to fpu_helper.c
target/ppc: introduce separate VSX_CMP macro for xvcmp* instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make kvmppc_xive_disconnect() able to undo the changes of a partial
execution of kvmppc_xive_connect() and use it to perform rollback.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <156198735673.293938.7313195993600841641.stgit@bahia>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When a CPU is reseted, the hypervisor (Linux or OPAL) invalidates the
POOL interrupt context of a CPU with this special command. It returns
the POOL CAM line value and resets the VP bit.
Fixes: 4836b45510 ("ppc/xive: activate HV support")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the software modifies the XIVE internal structures, ESB, EAS,
END, NVT, it also must update the caches of the different XIVE
sub-engines. HW offers a set of common interface for such purpose.
The CWATCH_SPEC register defines the block/index of the target and a
set of flags to perform a full update and to watch for update
conflicts.
The cache watch CWATCH_DATAX registers are then loaded with the target
data with a first read on CWATCH_DATA0. Writing back is done in the
opposit order, CWATCH_DATA0 triggering the update.
The SCRUB_TRIG registers are used to flush the cache in RAM, and to
possibly invalidate it. Cache disablement is also an option but as we
do not model the cache, these registers are no-ops
Today, the modeling of these registers is incorrect but it did not
impact the set up of a baremetal system. However, running KVM requires
a rework.
Fixes: 2dfa91a2aa ("ppc/pnv: add a XIVE interrupt controller model for POWER9")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the hypervisor (KVM) dispatches a vCPU on a HW thread, it restores
its thread interrupt context. The Pending Interrupt Priority Register
(PIPR) is computed from the Interrupt Pending Buffer (IPB) and stores
should not be allowed to change its value.
Fixes: 207d9fe985 ("ppc/xive: introduce the XIVE interrupt thread context")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When an interrupt needs to be delivered, the XIVE interrupt controller
presenter scans the CAM lines of the thread interrupt contexts of the
HW threads of the chip to find a matching vCPU. The interrupt context
is composed of 4 different sets of registers: Physical, HV, OS and
User.
The encoding of the Physical CAM line depends on the mode in which the
interrupt controller is operating: CAM mode or block group mode.
Block group mode being the default configuration today on POWER9 and
the only one available on the next POWER10 generation, enforce this
encoding in the Physical CAM line :
chip << 19 | 0000000 0 0001 thread (7Bit)
It fits the overall encoding of the NVT ids and simplifies the matching
algorithm in the presenter.
Fixes: d514c48d41 ("ppc/xive: hardwire the Physical CAM line of the thread context")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190630204601.30574-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt device is fully initialized at reset when the CAS
negotiation process has completed. Depending on the KVM capabilities,
the SpaprXive memory regions (ESB, TIMA) are initialized with a host
MMIO backend or a QEMU emulated backend. This results in a complex
initialization sequence partially done at realize and later at reset,
and some memory region leaks.
To simplify this sequence and to remove of the late initialization of
the emulated device which is required to be done only once, we
introduce new memory regions specific for KVM. These regions are
mapped as overlaps on top of the emulated device to make use of the
host MMIOs. Also provide proper cleanups of these regions when the
XIVE KVM device is destroyed to fix the leaks.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190614165920.12670-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make xics_kvm_disconnect() able to undo the changes of a partial execution
of xics_kvm_connect() and use it to perform rollback.
Note that kvmppc_define_rtas_kernel_token(0) never fails, no matter the
RTAS call has been defined or not.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077922319.433243.609897156640506891.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This allows errors happening there to be propagated up to spapr_irq,
just like XIVE already does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077921763.433243.4614327010172954196.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Passing both errp and &local_err to functions is a recipe for messing
things up.
Since we must use &local_err for icp_kvm_realize(), use &local_err
everywhere where rollback must happen and have a single call to
error_propagate() them all. While here, add errno to the error
message.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077921212.433243.11716701611944816815.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no need to rollback anything at this point, so just return an
error.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077920657.433243.13541093940589972734.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Switch to using the connect/disconnect terminology like we already do for
XIVE.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077920102.433243.6605099291134598170.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Checking that we're not using the in-kernel XICS is ok with the "xics"
interrupt controller mode, but it is definitely not enough with the
other modes since the guest could be using XIVE.
Ensure XIVE is not in use when emulated XICS RTAS/hypercalls are
called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156077253666.424706.6104557911104491047.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
So that no one is tempted to drop that code, which is never called
for cold plugged CPUs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156078063349.435533.12283208810037409702.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Older KVMs on POWER9 don't support destroying/recreating a KVM XICS
device, which is required by 'dual' interrupt controller mode. This
causes QEMU to emit a warning when the guest is rebooted and to fall
back on XICS emulation:
qemu-system-ppc64: warning: kernel_irqchip allowed but unavailable:
Error on KVM_CREATE_DEVICE for XICS: File exists
If kernel irqchip is required, QEMU will thus exit when the guest is
first rebooted. Failing QEMU this late may be a painful experience
for the user.
Detect that and exit at machine init instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044430517.125694.6207865998817342638.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU may crash when running a spapr machine in 'dual' interrupt controller
mode on some older (but not that old, eg. ubuntu 18.04.2) KVMs with partial
XIVE support:
qemu-system-ppc64: hw/ppc/spapr_rtas.c:411: spapr_rtas_register:
Assertion `!name || !rtas_table[token].name' failed.
XICS is controlled by the guest thanks to a set of RTAS calls. Depending
on whether KVM XICS is used or not, the RTAS calls are handled by KVM or
QEMU. In both cases, QEMU needs to expose the RTAS calls to the guest
through the "rtas" node of the device tree.
The spapr_rtas_register() helper takes care of all of that: it adds the
RTAS call token to the "rtas" node and registers a QEMU callback to be
invoked when the guest issues the RTAS call. In the KVM XICS case, QEMU
registers a dummy callback that just prints an error since it isn't
supposed to be invoked, ever.
Historically, the XICS controller was setup during machine init and
released during final teardown. This changed when the 'dual' interrupt
controller mode was added to the spapr machine: in this case we need
to tear the XICS down and set it up again during machine reset. The
crash happens because we indeed have an incompatibility with older
KVMs that forces QEMU to fallback on emulated XICS, which tries to
re-registers the same RTAS calls.
This could be fixed by adding proper rollback that would unregister
RTAS calls on error. But since the emulated RTAS calls in QEMU can
now detect when they are mistakenly called while KVM XICS is in
use, it seems simpler to register them once and for all at machine
init. This fixes the crash and allows to remove some now useless
lines of code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429963.125694.13710679451927268758.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICS-related RTAS calls and hypercalls in QEMU are not supposed to
be called when the KVM in-kernel XICS is in use.
Add some explicit checks to detect that, print an error message and report
an hardware error to the guest.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156044429419.125694.507569071972451514.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
[dwg: Correction to commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The firmware (skiboot) of the PowerNV machines can configure the XIVE
interrupt controller to activate StoreEOI on the ESB pages of the
interrupts. This feature lets software do an EOI with a store instead
of a load. It is not activated today on P9 for rare race condition
issues but it should be on future processors.
Nevertheless, QEMU has a model for StoreEOI which can be used today by
experimental firmwares. But, the use of object_property_set_int() in
the PnvXive model is incorrect and crashes QEMU. Replace it with a
direct access to the ESB flags of the XiveSource object modeling the
internal sources of the interrupt controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190612162357.29566-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The legacy interface only supported up to 32 IRQs, which became
restrictive around the AST2400 generation. QEMU support for the SoCs
started with the AST2400 along with an effort to reimplement and
upstream drivers for Linux, so up until this point the consumers of the
QEMU ASPEED support only required the 64 IRQ register interface.
In an effort to support older BMC firmware, add support for the 32 IRQ
interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-22-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv3 specification says that the GICD_TYPER.SecurityExtn bit
is RAZ if GICD_CTLR.DS is 1. We were incorrectly making it RAZ
if the security extension is unsupported. "Security extension
unsupported" always implies GICD_CTLR.DS == 1, but the guest can
also set DS on a GIC which does support the security extension.
Fix the condition to correctly check the GICD_CTLR.DS bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190524124248.28394-3-peter.maydell@linaro.org
The GIC ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524124248.28394-2-peter.maydell@linaro.org
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
-----BEGIN PGP SIGNATURE-----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=ERgu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190612' into staging
ppc patch queue 2019-06-12
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
# gpg: Signature made Wed 12 Jun 2019 06:47:56 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190612:
ppc/xive: Make XIVE generate the proper interrupt types
ppc/pnv: activate the "dumpdtb" option on the powernv machine
target/ppc: Use tcg_gen_gvec_bitsel
spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges
spapr: Direct all PCI hotplug to host bridge, rather than P2P bridge
spapr: Don't use bus number for building DRC ids
spapr: Clean up DRC index construction
spapr: Clean up spapr_drc_populate_dt()
spapr: Clean up dt creation for PCI buses
spapr: Clean up device tree construction for PCI devices
spapr: Clean up device node name generation for PCI devices
target/ppc: Fix lxvw4x, lxvh8x and lxvb16x
spapr_pci: Improve error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
It should be generic Hypervisor Virtualization interrupts for HV
directed rings and traditional External Interrupts for the OS directed
ring.
Don't generate anything for the user ring as it isn't actually
supported.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190606174409.12502-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cleanup in the boilerplate that each target must define.
Replace mips_env_get_cpu with env_archcpu. The combination
CPU(mips_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Today, when a reset occurs on a pseries machine using the 'dual'
interrupt mode, the KVM devices are released and recreated depending
on the interrupt mode selected by CAS. If XIVE is selected, the SysBus
memory regions of the SpaprXive model are initialized by the KVM
backend initialization routine each time a reset occurs. This leads to
a crash after a couple of resets because the machine reaches the
QDEV_MAX_MMIO limit of SysBusDevice :
qemu-system-ppc64: hw/core/sysbus.c:193: sysbus_init_mmio: Assertion `dev->num_mmio < QDEV_MAX_MMIO' failed.
To fix, initialize the SysBus memory regions in spapr_xive_realize()
called only once and remove the same inits from the QEMU and KVM
backend initialization routines which are called at each reset.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190522074016.10521-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt mode is chosen by the CAS negotiation process and
activated after a reset to take into account the required changes in
the machine. This brings new constraints on how the associated KVM IRQ
device is initialized.
Currently, each model takes care of the initialization of the KVM
device in their realize method but this is not possible anymore as the
initialization needs to be done globaly when the interrupt mode is
known, i.e. when machine is reseted. It also means that we need a way
to delete a KVM device when another mode is chosen.
Also, to support migration, the QEMU objects holding the state to
transfer should always be available but not necessarily activated.
The overall approach of this proposal is to initialize both interrupt
mode at the QEMU level to keep the IRQ number space in sync and to
allow switching from one mode to another. For the KVM side of things,
the whole initialization of the KVM device, sources and presenters, is
grouped in a single routine. The XICS and XIVE sPAPR IRQ reset
handlers are modified accordingly to handle the init and the delete
sequences of the KVM device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Recent commits changed the behavior of ics_set_irq_type() to
initialize correctly LSIs at the KVM level. ics_set_irq_type() is also
called by the realize routine of the different devices of the machine
when initial interrupts are claimed, before the ICSState device is
reseted.
In the case, the ICSIRQState priority is 0x0 and the call to
ics_set_irq_type() results in configuring the target of the
interrupt. On P9, when using the KVM XICS-on-XIVE device, the target
is configured to be server 0, priority 0 and the event queue 0 is
created automatically by KVM.
With the dual interrupt mode creating the KVM device at reset, it
leads to unexpected effects on the guest, mostly blocking IPIs. This
is wrong, fix it by reseting the ICSIRQState structure when
ics_set_irq_type() is called.
Fixes: commit 6cead90c5c ("xics: Write source state to KVM at claim time")
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-14-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a check to make sure that the routine initializing the emulated
IRQ device is called once. We don't have much to test on the XICS
side, so we introduce a 'init' boolean under ICSState.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The way the XICS and the XIVE devices are initialized follows the same
pattern. First, try to connect to the KVM device and if not possible
fallback on the emulated device, unless a kernel_irqchip is required.
The spapr_irq_init_device() routine implements this sequence in
generic way using new sPAPR IRQ handlers ->init_emu() and ->init_kvm().
The XIVE init sequence is moved under the associated sPAPR IRQ
->init() handler. This will change again when KVM support is added for
the dual interrupt mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The activation of the KVM IRQ device depends on the interrupt mode
chosen at CAS time by the machine and some methods used at reset or by
the migration need to be protected.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a new interrupt mode is chosen by CAS, the machine generates a
reset to reconfigure. At this point, the connection with the previous
KVM device needs to be closed and a new connection needs to opened
with the KVM device operating the chosen interrupt mode.
New routines are introduced to destroy the XICS and the XIVE KVM
devices. They make use of a new KVM device ioctl which destroys the
device and also disconnects the IRQ presenters from the vCPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the VM is stopped, the VM state handler stabilizes the XIVE IC
and marks the EQ pages dirty. These are then transferred to destination
before the transfer of the device vmstates starts.
The SpaprXive interrupt controller model captures the XIVE internal
tables, EAT and ENDT and the XiveTCTX model does the same for the
thread interrupt context registers.
At restart, the SpaprXive 'post_load' method restores all the XIVE
states. It is called by the sPAPR machine 'post_load' method, when all
XIVE states have been transferred and loaded.
Finally, the source states are restored in the VM change state handler
when the machine reaches the running state.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This handler is in charge of stabilizing the flow of event notifications
in the XIVE controller before migrating a guest. This is a requirement
before transferring the guest EQ pages to a destination.
When the VM is stopped, the handler sets the source PQs to PENDING to
stop the flow of events and to possibly catch a triggered interrupt
occuring while the VM is stopped. Their previous state is saved. The
XIVE controller is then synced through KVM to flush any in-flight
event notification and to stabilize the EQs. At this stage, the EQ
pages are marked dirty to make sure the EQ pages are transferred if a
migration sequence is in progress.
The previous configuration of the sources is restored when the VM
resumes, after a migration or a stop. If an interrupt was queued while
the VM was stopped, the handler simply generates the missing trigger.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This extends the KVM XIVE device backend with 'synchronize_state'
methods used to retrieve the state from KVM. The HW state of the
sources, the KVM device and the thread interrupt contexts are
collected for the monitor usage and also migration.
These get operations rely on their KVM counterpart in the host kernel
which acts as a proxy for OPAL, the host firmware. The set operations
will be added for migration support later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
XIVE hcalls are all redirected to QEMU as none are on a fast path.
When necessary, QEMU invokes KVM through specific ioctls to perform
host operations. QEMU should have done the necessary checks before
calling KVM and, in case of failure, H_HARDWARE is simply returned.
H_INT_ESB is a special case that could have been handled under KVM
but the impact on performance was low when under QEMU. Here are some
figures :
kernel irqchip OFF ON
H_INT_ESB KVM QEMU
rtl8139 (LSI ) 1.19 1.24 1.23 Gbits/sec
virtio 31.80 42.30 -- Gbits/sec
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This introduces a set of helpers when KVM is in use, which create the
KVM XIVE device, initialize the interrupt sources at a KVM level and
connect the interrupt presenters to the vCPU.
They also handle the initialization of the TIMA and the source ESB
memory regions of the controller. These have a different type under
KVM. They are 'ram device' memory mappings, similarly to VFIO, exposed
to the guest and the associated VMAs on the host are populated
dynamically with the appropriate pages using a fault handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of LISN i.e "Logical Interrupt Source Number" as per
Xive PAPR document "info pic" prints as LSIN, let's fix it.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Message-Id: <20190509080750.21999-1-sathnaga@linux.vnet.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This proved to be a useful information when debugging issues with OS
event queues allocated above 64GB.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-4-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The high order bits of the address of the OS event queue is stored in
bits [4-31] of word2 of the XIVE END internal structures and the low
order bits in word3. This structure is using Big Endian ordering and
computing the value requires some simple arithmetic which happens to
be wrong. The mask removing bits [0-3] of word2 is applied to the
wrong value and the resulting address is bogus when above 64GB.
Guests with more than 64GB of RAM will allocate pages for the OS event
queues which will reside above the 64GB limit. In this case, the XIVE
device model will wake up the CPUs in case of a notification, such as
IPIs, but the update of the event queue will be written at the wrong
place in memory. The result is uncertain as the guest memory is
trashed and IPI are not delivered.
Introduce a helper xive_end_qaddr() to compute this value correctly in
all places where it is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the OS configures the EQ page in which to receive event
notifications from the XIVE interrupt controller, the page should be
naturally aligned. Add this check.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-2-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
[dwg: Minor change for printf warning on some platforms]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let NVIC adopt the SysTick timer.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-17-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The ICC_CTLR_EL3 register includes some bits which are aliases
of bits in the ICC_CTLR_EL1(S) and (NS) registers. QEMU chooses
to keep those bits in the cs->icc_ctlr_el1[] struct fields.
Unfortunately a missing '~' in the code to update the bits
in those fields meant that writing to ICC_CTLR_EL3 would corrupt
the ICC_CLTR_EL1 register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190520162809.2677-5-peter.maydell@linaro.org
In ich_vmcr_write() we enforce "writes of BPR fields to less than
their minimum sets them to the minimum" by doing a "read vbpr and
write it back" operation. A typo here meant that we weren't handling
writes to these fields correctly, because we were reading from VBPR0
but writing to VBPR1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190520162809.2677-4-peter.maydell@linaro.org
The hw/arm/arm.h header now only includes declarations relating
to boot.c code, so it is only needed by Arm board or SoC code.
Remove some unnecessary inclusions of it from target/arm files
and from hw/intc/armv7m_nvic.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-3-peter.maydell@linaro.org
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3rY3AAoJEL/70l94x66D91kH/21LLnL+sKmyueSM/Sek4id2
r06tHdGMdl5Od3I5uMD9gnr4AriiCZc9ybQDQ1N879wKMmQPZwcnf2GJ5DZ0wa3L
jHoQO07Bg0KZGWALjXiN5PWB0DlJtXsTm0C4q4tnt6V/ueasjxouBk9/fRLRc09n
QTS379X9QvPElFTv3WPfGz6kmkLq8VMmdRnSlXneB9xTyXXJbFj3zlvDCElNSgWh
fZ7gnfYWB1LOC19HJxp1mJSkAUD5AgImYEK1Hmnr+BMs2sg6gypYNtp3LtE5FzmZ
HSdXYFyPkQV9UyTiV1XBs3bXJbGYj5OApfXCtwo/I2JtP+LhHBA2eq1Gs3QgP98=
=zSSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Mostly bugfixes and cleanups, the most important being
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
# gpg: Signature made Fri 17 May 2019 14:25:11 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (21 commits)
hw/net/ne2000: Extract the PCI device from the chipset common code
hw/char: Move multi-serial devices into separate file
ioapic: allow buggy guests mishandling level-triggered interrupts to make progress
build: don't build hardware objects with linux-user
build: chardev is only needed for softmmu targets
configure: qemu-ga is only needed with softmmu targets
build: replace GENERATED_FILES by generated-files-y
trace: only include trace-event-subdirs when they are needed
sun4m: obey -vga none
mips-fulong2e: obey -vga none
hw/i386/acpi: Assert a pointer is not null BEFORE using it
hw/i386/acpi: Add object_resolve_type_unambiguous to improve modularity
hw/acpi/piix4: Move TYPE_PIIX4_PM to a public header
memory: correct the comment to DIRTY_MEMORY_MIGRATION
vl: fix -sandbox parsing crash when seccomp support is disabled
hvf: Add missing break statement
megasas: fix mapped frame size
vl: Add missing descriptions to the VGA adapters list
Declare -realtime as deprecated
roms: assert if max rom size is less than the used size
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It was found that Hyper-V 2016 on KVM in some configurations (q35 machine +
piix4-usb-uhci) hangs on boot. Root-cause was that one of Hyper-V
level-triggered interrupt handler performs EOI before fixing the cause of
the interrupt. This results in IOAPIC keep re-raising the level-triggered
interrupt after EOI because irq-line remains asserted.
Gory details: https://www.spinics.net/lists/kvm/msg184484.html
(the whole thread).
Turns out we were dealing with similar issues before; in-kernel IOAPIC
implementation has commit 184564efae4d ("kvm: ioapic: conditionally delay
irq delivery duringeoi broadcast") which describes a very similar issue.
Steal the idea from the above mentioned commit for IOAPIC implementation in
QEMU. SUCCESSIVE_IRQ_MAX_COUNT, delay and the comment are borrowed as well.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190402080215.10747-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The M-profile architecture specifies that the DebugMonitor exception
should be initially disabled, not enabled. It should be controlled
by the DEMCR register's MON_EN bit, but we don't implement that
register yet (like most of the debug architecture for M-profile).
Note that BKPT instructions will still work, because they
will be escalated to HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-4-peter.maydell@linaro.org
The non-secure versions of the BFAR and BFSR registers are
supposed to be RAZ/WI if AICR.BFHFNMINS == 0; we were
incorrectly allowing NS code to access the real values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-3-peter.maydell@linaro.org
Rule R_CQRV says that if two pending interrupts have the same
group priority then ties are broken by looking at the subpriority.
We had a comment describing this but had forgotten to actually
implement the subpriority comparison. Correct the omission.
(The further tie break rules of "lowest exception number" and
"secure before non-secure" are handled implicitly by the order
in which we iterate through the exceptions in the loops.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190430131439.25251-2-peter.maydell@linaro.org
In the v7M architecture, if an exception is generated in the process
of doing the lazy stacking of FP registers, the handling of
possible escalation to HardFault is treated differently to the normal
approach: it works based on the saved information about exception
readiness that was stored in the FPCCR when the stack frame was
created. Provide a new function armv7m_nvic_set_pending_lazyfp()
which pends exceptions during lazy stacking, and implements
this logic.
This corresponds to the pseudocode TakePreserveFPException().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-22-peter.maydell@linaro.org
Implement the code which updates the FPCCR register on an
exception entry where we are going to use lazy FP stacking.
We have to defer to the NVIC to determine whether the
various exceptions are currently ready or not.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190416125744.27770-12-peter.maydell@linaro.org
The M-profile floating point support has three associated config
registers: FPCAR, FPCCR and FPDSCR. It also makes the registers
CPACR and NSACR have behaviour other than reads-as-zero.
Add support for all of these as simple reads-as-written registers.
We will hook up actual functionality later.
The main complexity here is handling the FPCCR register, which
has a mix of banked and unbanked bits.
Note that we don't share storage with the A-profile
cpu->cp15.nsacr and cpu->cp15.cpacr_el1, though the behaviour
is quite similar, for two reasons:
* the M profile CPACR is banked between security states
* it preserves the invariant that M profile uses no state
inside the cp15 substruct
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-4-peter.maydell@linaro.org
For M-profile the MVFR* ID registers are memory mapped, in the
range we implement via the NVIC. Allow them to be read.
(If the CPU has no FPU, these registers are defined to be RAZ.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190416125744.27770-3-peter.maydell@linaro.org
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
H_IPOLL takes the CPU# of the processor to poll as an argument,
it doesn't operate on self.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190314063855.27890-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The BCM2836 control logic module includes a simple
"local timer" which is a programmable down-counter that
can generates an interrupt. Implement this functionality.
Signed-off-by: Zoltán Baldaszti <bztemail@gmail.com>
[PMM: wrote commit message; wrapped long line; tweaked
some comments to match the final version of the code]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qemu coding standard is to use CamelCase for type and structure names,
and the pseries code follows that... sort of. There are quite a lot of
places where we bend the rules in order to preserve the capitalization of
internal acronyms like "PHB", "TCE", "DIMM" and most commonly "sPAPR".
That was a bad idea - it frequently leads to names ending up with hard to
read clusters of capital letters, and means they don't catch the eye as
type identifiers, which is kind of the point of the CamelCase convention in
the first place.
In short, keeping type identifiers look like CamelCase is more important
than preserving standard capitalization of internal "words". So, this
patch renames a heap of spapr internal type names to a more standard
CamelCase.
In addition to case changes, we also make some other identifier renames:
VIOsPAPR* -> SpaprVio*
The reverse word ordering was only ever used to mitigate the capital
cluster, so revert to the natural ordering.
VIOsPAPRVTYDevice -> SpaprVioVty
VIOsPAPRVLANDevice -> SpaprVioVlan
Brevity, since the "Device" didn't add useful information
sPAPRDRConnector -> SpaprDrc
sPAPRDRConnectorClass -> SpaprDrcClass
Brevity, and makes it clearer this is the same thing as a "DRC"
mentioned in many other places in the code
This is 100% a mechanical search-and-replace patch. It will, however,
conflict with essentially any and all outstanding patches touching the
spapr code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The NSR register of the HV ring has a different, although similar, bit
layout. TM_QW3_NSR_HE_PHYS bit should now be raised when the
Hypervisor interrupt line is signaled. Other bits TM_QW3_NSR_HE_POOL
and TM_QW3_NSR_HE_LSI are not modeled. LSI are for special interrupts
reserved for HW bringup and the POOL bit is used when signaling a
group of VPs. This is not currently implemented in Linux but it is in
pHyp.
The most important special commands on the HV TIMA page are added to
let the core manage interrupts : acking and changing the CPU priority.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine with need to encode the block id in the source
interrupt number before forwarding the source event notification to
the Router.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PowerNV machine can perform indirect loads and stores on the TIMA
on behalf of another CPU. Give the controller the possibility to call
the TIMA memory accessors with a XiveTCTX of its choice.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
By default on P9, the HW CAM line (23bits) is hardwired to :
0x000||0b1||4Bit chip number||7Bit Thread number.
When the block group mode is enabled at the controller level (PowerNV),
the CAM line is changed for CAM compares to :
4Bit chip number||0x001||7Bit Thread number
This will require changes in xive_presenter_tctx_match() possibly.
This is a lowlevel functionality of the HW controller and it is not
strictly needed. Leave it for later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The POWERNV switch should always select ISA_IPMI_BT, then the other
IPMI options are turned on automatically now.
CONFIG_DIMM should always be selected by the pseries machine,
which in turn depends on CONFIG_MEM_DEVICE since DIMM implements
this interface.
CONFIG_VIRTIO_VGA can be dropped from default-configs/ppc64-softmmu.mak
completely since this device is already automatically enabled via
hw/display/Kconfig now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both functions, object_initialize() and object_property_add_child() increase
the reference counter of the new object, so one of the references has to be
dropped afterwards to get the reference counting right. Otherwise the child
object will not be properly cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the reference
counting here right.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1550748288-30598-1-git-send-email-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Patch "target/ppc: Add POWER9 external interrupt model" should have
removed the section covering PPC_FLAGS_INPUT_POWER7.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190219142530.17807-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be needed by PHB hotplug in order to access the "phandle"
property of the interrupt controller node.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059668867.1466090.6339199751719123386.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries machine only uses LSIs to support legacy PCI devices. Every
PHB claims 4 LSIs at realize time. When using in-kernel XICS (or upcoming
in-kernel XIVE), QEMU synchronizes the state of all irqs, including these
LSIs, later on at machine reset.
In order to support PHB hotplug, we need a way to tell KVM about the LSIs
that doesn't require a machine reset. An easy way to do that is to always
inform KVM when an interrupt is claimed, which really isn't a performance
path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059668360.1466090.5969630516627776426.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICS reset handler simply writes the ICS state to KVM. This
doesn't need the overkill parent_reset logic we have today. Also
we want to use the same ICS type for the KVM and non-KVM case with
pseries.
Call icp_set_kvm_state() from the "simple" ICS reset function.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082407.1011724.1983100830860273401.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MSI is the default and LSI specific code is guarded by the
xive_source_irq_is_lsi() helper. The xive_source_irq_set()
helper is a nop for MSIs.
Simplify the code by turning xive_source_irq_set() into
xive_source_irq_set_lsi() and only call it for LSIs. The
call to xive_source_irq_set(false) in spapr_xive_irq_free()
is also a nop. Just drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <154999584656.690774.18352404495120358613.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The code for handling the NVIC SHPR1 register intends to permit
byte and halfword accesses (as the architecture requires). However
the 'case' line for it only lists the base address of the
register, so attempts to access bytes other than the first one
end up in the "bad write" default logic. This bug was added
accidentally when we split out the SHPR1 logic from SHPR2 and
SHPR3 to support v6M.
Fixes: 7c9140afd5 ("nvic: Handle ARMv6-M SCS reserved registers")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
---
The Zephyr RTOS happens to access SHPR1 byte at a time,
which is how I spotted this.
Next step is to remove them from under the PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It provides a mean to retrieve the XiveTCTX of a CPU. This will become
necessary with future changes which move the interrupt presenter
object pointers under the PowerPCCPU machine_data.
The PowerNV machine has an extra requirement on TIMA accesses that
this new method addresses. The machine can perform indirect loads and
stores on the TIMA on behalf of another CPU. The PIR being defined in
the controller registers, we need a way to peek in the controller
model to find the PIR value.
The XiveTCTX is moved above the XiveRouter definition to avoid forward
typedef declarations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently the ARMv7M NVIC object's realize method assumes that the
CPU the NVIC is attached to is CPU 0, because it thinks there can
only ever be one CPU in the system. To allow a dual-Cortex-M33
setup we need to remove this assumption; instead the armv7m
wrapper object tells the NVIC its CPU, in the same way that it
already tells the CPU what the NVIC is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-2-peter.maydell@linaro.org
When compiling with Clang in -std=gnu99 mode, there is a warning/error:
CC ppc64-softmmu/hw/intc/xics_spapr.o
In file included from /home/thuth/devel/qemu/hw/intc/xics_spapr.c:34:
/home/thuth/devel/qemu/include/hw/ppc/xics.h:203:34: error: redefinition of typedef 'sPAPRMachineState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct sPAPRMachineState sPAPRMachineState;
^
/home/thuth/devel/qemu/include/hw/ppc/spapr_irq.h:25:34: note: previous definition is here
typedef struct sPAPRMachineState sPAPRMachineState;
^
We have to remove the duplicated typedef here and include "spapr.h" instead.
But "spapr.h" should not be included for the pnv machine files. So move
the spapr-related prototypes into a new file called "xics_spapr.h" instead.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the 'intc' pointer is only used by the XICS interrupt mode,
let's make things clear and use a XICS type and name.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
which will be used by the machine only when the XIVE interrupt mode is
in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the time being, the XIVE reset handler updates the OS CAM line of
the vCPU as it is done under a real hypervisor when a vCPU is
scheduled to run on a HW thread. This will let the XIVE presenter
engine find a match among the NVTs dispatched on the HW threads.
This handler will become even more useful when we introduce the
machine supporting both interrupt modes, XIVE and XICS. In this
machine, the interrupt mode is chosen by the CAS negotiation process
and activated after a reset.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each interrupt mode has its own specific interrupt presenter object,
that we store under the CPU object, one for XICS and one for XIVE.
Extend the sPAPR IRQ backend with a new handler to support them both.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE interface for the guest is described in the device tree under
the "interrupt-controller" node. A couple of new properties are
specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), for the User level and for the Guest OS
level. Only the Guest OS level is taken into account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the IRQ interrupt number ranges assigned to the guest for the IPIs.
and also under the root node :
- "ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use. OPAL uses the priority 7 queue to automatically
escalate interrupts for all other queues (DD2.X POWER9). So only
priorities [0..6] are allowed for the guest.
Extend the sPAPR IRQ backend with a new handler to populate the DT
with the appropriate "interrupt-controller" node.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The different XIVE virtualization structures (sources and event queues)
are configured with a set of Hypervisor calls :
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (ESB) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification configuration associated
with the queue, only unconditional notification is supported for
the moment. Reset is performed with a queue size of 0 and queueing
is disabled in that case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the guest's internal interrupt structures to their
initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure all notifications
have reached their queue.
Calls that still need to be addressed :
H_INT_SET_OS_REPORTING_LINE
H_INT_GET_OS_REPORTING_LINE
See the code for more documentation on each hcall.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The IVPE scans the O/S CAM line of the XIVE thread interrupt contexts
to find a matching Notification Virtual Target (NVT) among the NVTs
dispatched on the HW processor threads.
On a real system, the thread interrupt contexts are updated by the
hypervisor when a Virtual Processor is scheduled to run on a HW
thread. Under QEMU, the model will emulate the same behavior by
hardwiring the NVT identifier in the thread context registers at
reset.
The NVT identifier used by the sPAPRXive model is the VCPU id. The END
identifier is also derived from the VCPU id. A set of helpers doing
the conversion between identifiers are provided for the hcalls
configuring the sources and the ENDs.
The model does not need a NVT table but the XiveRouter NVT operations
are provided to perform some extra checks in the routing algorithm.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
sPAPRXive models the XIVE interrupt controller of the sPAPR machine.
It inherits from the XiveRouter and provisions storage for the routing
tables :
- Event Assignment Structure (EAS)
- Event Notification Descriptor (END)
The sPAPRXive model incorporates an internal XiveSource for the IPIs
and for the interrupts of the virtual devices of the guest. This model
is consistent with XIVE architecture which also incorporates an
internal IVSE for IPIs and accelerator interrupts in the IVRE
sub-engine.
The sPAPRXive model exports two memory regions, one for the ESB
trigger and management pages used to control the sources and one for
the TIMA pages. They are mapped by default at the addresses found on
chip 0 of a baremetal system. This is also consistent with the XIVE
architecture which defines a Virtualization Controller BAR for the
internal IVSE ESB pages and a Thread Managment BAR for the TIMA.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fold in field accessor fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
After the event data was enqueued in the O/S Event Queue, the IVPE
raises the bit corresponding to the priority of the pending interrupt
in the register IBP (Interrupt Pending Buffer) to indicate there is an
event pending in one of the 8 priority queues. The Pending Interrupt
Priority Register (PIPR) is also updated using the IPB. This register
represent the priority of the most favored pending notification.
The PIPR is then compared to the the Current Processor Priority
Register (CPPR). If it is more favored (numerically less than), the
CPU interrupt line is raised and the EO bit of the Notification Source
Register (NSR) is updated to notify the presence of an exception for
the O/S. The check needs to be done whenever the PIPR or the CPPR are
changed.
The O/S acknowledges the interrupt with a special load in the Thread
Interrupt Management Area. If the EO bit of the NSR is set, the CPPR
takes the value of PIPR. The bit number in the IBP corresponding to
the priority of the pending interrupt is reseted and so is the EO bit
of the NSR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last sub-engine of the XIVE architecture is the Interrupt
Virtualization Presentation Engine (IVPE). On HW, the IVRE and the
IVPE share elements, the Power Bus interface (CQ), the routing table
descriptors, and they can be combined in the same HW logic. We do the
same in QEMU and combine both engines in the XiveRouter for
simplicity.
When the IVRE has completed its job of matching an event source with a
Notification Virtual Target (NVT) to notify, it forwards the event
notification to the IVPE sub-engine. The IVPE scans the thread
interrupt contexts of the Notification Virtual Targets (NVT)
dispatched on the HW processor threads and if a match is found, it
signals the thread. If not, the IVPE escalates the notification to
some other targets and records the notification in a backlog queue.
The IVPE maintains the thread interrupt context state for each of its
NVTs not dispatched on HW processor threads in the Notification
Virtual Target table (NVTT).
The model currently only supports single NVT notifications.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each POWER9 processor chip has a XIVE presenter that can generate four
different exceptions to its threads:
- hypervisor exception,
- O/S exception
- Event-Based Branch (EBB)
- msgsnd (doorbell).
Each exception has a state independent from the others called a Thread
Interrupt Management context. This context is a set of registers which
lets the thread handle priority management and interrupt acknowledgment
among other things. The most important ones being :
- Interrupt Priority Register (PIPR)
- Interrupt Pending Buffer (IPB)
- Current Processor Priority (CPPR)
- Notification Source Register (NSR)
These registers are accessible through a specific MMIO region, called
the Thread Interrupt Management Area (TIMA), four aligned pages, each
exposing a different view of the registers. First page (page address
ending in 0b00) gives access to the entire context and is reserved for
the ring 0 view for the physical thread context. The second (page
address ending in 0b01) is for the hypervisor, ring 1 view. The third
(page address ending in 0b10) is for the operating system, ring 2
view. The fourth (page address ending in 0b11) is for user level, ring
3 view.
The thread interrupt context is modeled with a XiveTCTX object
containing the values of the different exception registers. The TIMA
region is mapped at the same address for each CPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Event Notification Descriptor (END) XIVE structure also contains
two Event State Buffers providing further coalescing of interrupts,
one for the notification event (ESn) and one for the escalation events
(ESe). A MMIO page is assigned for each to control the EOI through
loads only. Stores are not allowed.
The END ESBs are modeled through an object resembling the 'XiveSource'
It is stateless as the END state bits are backed into the XiveEND
structure under the XiveRouter and the MMIO accesses follow the same
rules as for the XiveSource ESBs.
END ESBs are not supported by the Linux drivers neither on OPAL nor on
sPAPR. Nevetherless, it provides a mean to study the question in the
future and validates a bit more the XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix for field access]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To complete the event routing, the IVRE sub-engine uses a second table
containing Event Notification Descriptor (END) structures.
An END specifies on which Event Queue (EQ) the event notification
data, defined in the associated EAS, should be posted when an
exception occurs. It also defines which Notification Virtual Target
(NVT) should be notified.
The Event Queue is a memory page provided by the O/S defining a
circular buffer, one per server and priority couple, containing Event
Queue entries. These are 4 bytes long, the first bit being a
'generation' bit and the 31 following bits the END Data field. They
are pulled by the O/S when the exception occurs.
The END Data field is a way to set an invariant logical event source
number for an IRQ. On sPAPR machines, it is set with the
H_INT_SET_SOURCE_CONFIG hcall when the EISN flag is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix from Cédric fixing field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveRouter models the second sub-engine of the XIVE architecture :
the Interrupt Virtualization Routing Engine (IVRE).
The IVRE handles event notifications of the IVSE and performs the
interrupt routing process. For this purpose, it uses a set of tables
stored in system memory, the first of which being the Event Assignment
Structure (EAS) table.
The EAT associates an interrupt source number with an Event Notification
Descriptor (END) which will be used in a second phase of the routing
process to identify a Notification Virtual Target.
The XiveRouter is an abstract class which needs to be inherited from
to define a storage for the EAT, and other upcoming tables.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in parts of a later fix by Cédric fixing field access]
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveNotifier offers a simple interface, between the XiveSource
object and the main interrupt controller of the machine. It will
forward event notifications to the XIVE Interrupt Virtualization
Routing Engine (IVRE).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Adjust type name string for XiveNotifier]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'sent' status of the LSI interrupt source is modeled with the 'P'
bit of the ESB and the assertion status of the source is maintained
with an extra bit under the main XiveSource object. The type of the
source is stored in the same array for practical reasons.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The first sub-engine of the overall XIVE architecture is the Interrupt
Virtualization Source Engine (IVSE). An IVSE can be integrated into
another logic, like in a PCI PHB or in the main interrupt controller
to manage IPIs.
Each IVSE instance is associated with an Event State Buffer (ESB) that
contains a two bit state entry for each possible event source. When an
event is signaled to the IVSE, by MMIO or some other means, the
associated interrupt state bits are fetched from the ESB and
modified. Depending on the resulting ESB state, the event is forwarded
to the IVRE sub-engine of the controller doing the routing.
Each supported ESB entry is associated with either a single or a
even/odd pair of pages which provides commands to manage the source:
to EOI, to turn off the source for instance.
On a sPAPR machine, the O/S will obtain the page address of the ESB
entry associated with a source and its characteristic using the
H_INT_GET_SOURCE_INFO hcall. On PowerNV, a similar OPAL call is used.
The xive_source_notify() routine is in charge forwarding the source
event notification to the routing engine. It will be filled later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The API of cpu_physical_memory_write_rom() is odd, because it
takes an AddressSpace, unlike all the other cpu_physical_memory_*
access functions. Rename it to address_space_write_rom(), and
bring its API into line with address_space_write().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20181122133507.30950-3-peter.maydell@linaro.org
Replace arm_hcr_el2_{fmo,imo,amo} with a more general routine
that also takes SCR_EL3.NS (aka arm_is_secure_below_el3) into
account, as documented for the plethora of bits in HCR_EL2.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181210150501.7990-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
puv3_intc_class_init().
Cc: gxt@mprc.pku.edu.cn
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-11-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create struct ARMISARegisters, to be accessed during translation.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling error_report() in a function that takes an Error ** argument
is suspicious. ioapic_realize() does that, and then exit()s.
Currently mostly harmless, as the device cannot be hot-plugged.
Fixes: 20fd4b7b6d
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181017082702.5581-11-armbru@redhat.com>
Add a slight improvement of the Coccinelle semantic patch from commit
007b06578a, and use it to clean up. It leaves dead Error * variables
behind, cleaned up manually.
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Eric Blake <eblake@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20181017082702.5581-3-armbru@redhat.com>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
The GIC_BASE_IRQ macro is a leftover from when we shared code
between the GICv2 and the v7M NVIC. Since the NVIC is now
split off, GIC_BASE_IRQ is always 0, and we can just delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180824161819.11085-1-peter.maydell@linaro.org
Reduce the size of the per-cpu GICH memory regions from 0x1000
to 0x200. The registers only cover 0x200 bytes, and the Cortex-A15
wants to map them at a spacing of 0x200 bytes apart. Having the
region be too large interferes with mapping them like that, so
reduce it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-3-peter.maydell@linaro.org
Switch the apic away from using the old_mmio MemoryRegionOps
accessor functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180803101943.23722-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On real v7M hardware, the NMI line is an externally visible signal
that an SoC or board can toggle to assert an NMI. Expose it in
our QEMU NVIC and armv7m container objects so that a board model
can wire it up if it needs to.
In particular, the MPS2 watchdog is wired to NMI.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In scripts/arch-run.bash of kvm-unit-tests, it will check the qemu
output log with:
if [ -z "$(echo "$errors" | grep -vi warning)" ]; then
Thus without the warning prefix, all of the test fail.
Since it is not unrecoverable error in kvm_arm_its_reset for
current implementation, downgrading the report from error to
warn makes sense.
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Message-id: 1531969910-32843-1-git-send-email-jia.he@hxt-semitech.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IMO, FMO and AMO bits in HCR_EL2 are defined to "behave as
1 for all purposes other than direct reads" if HCR_EL2.TGE
is set and HCR_EL2.E2H is 0, and to "behave as 0 for all
purposes other than direct reads" if HCR_EL2.TGE is set
and HRC_EL2.E2H is 1.
To avoid having to check E2H and TGE everywhere where we test IMO and
FMO, provide accessors arm_hcr_el2_imo(), arm_hcr_el2_fmo()and
arm_hcr_el2_amo(). We don't implement ARMv8.1-VHE yet, so the E2H
case will never be true, but we include the logic to save effort when
we eventually do get to that.
(Note that in several of these callsites the change doesn't
actually make a difference as either the callsite is handling
TGE specially anyway, or the CPU can't get into that situation
with TGE set; we change everywhere for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180724115950.17316-5-peter.maydell@linaro.org
Add some traces to the ARM GIC to catch register accesses (distributor,
(v)cpu interface and virtual interface), and to take into account
virtualization extensions (print `vcpu` instead of `cpu` when needed).
Also add some virtualization extensions specific traces: LR updating
and maintenance IRQ generation.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-19-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the maintenance interrupt generation that is part of the GICv2
virtualization extensions.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-18-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the gic_update_virt() function to update the vCPU interface states
and raise vIRQ and vFIQ as needed. This commit renames gic_update() to
gic_update_internal() and generalizes it to handle both cases, with a
`virt' parameter to track whether we are updating the CPU or vCPU
interfaces.
The main difference between CPU and vCPU is the way we select the best
IRQ. This part has been split into the gic_get_best_(v)irq functions.
For the virt case, the LRs are iterated to find the best candidate.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the read and write functions for the virtual interface of the
virtualization extensions in the GICv2.
One mirror region per CPU is also created, which maps to that specific
CPU id. This is required by the GIC architecture specification.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-16-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the read/write functions to handle accesses to the vCPU interface.
Those accesses are forwarded to the real CPU interface, with the CPU id
being converted to the corresponding vCPU id (vCPU id = CPU id +
GIC_NCPU).
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180727095421.386-15-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_cpu_read() and
gic_cpu_write() functions. Those are the last bits missing to fully
support virtualization extensions in the CPU interface path.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-14-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_deactivate_irq() and
gic_complete_irq() functions.
When the guest writes an invalid vIRQ to V_EOIR or V_DIR, since the
GICv2 specification is not entirely clear here, we adopt the behaviour
observed on real hardware:
* When V_CTRL.EOIMode is false (EOI split is disabled):
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop, and increments V_HCR.EOICount.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR is ignored.
* When V_CTRL.EOIMode is true:
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR increments V_HCR.EOICount.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180727095421.386-13-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_acknowledge_irq()
function. This function changes the state of the highest priority IRQ
from pending to active.
When the current CPU is a vCPU, modifying the state of an IRQ modifies
the corresponding LR entry. However if we clear the pending flag before
setting the active one, we lose track of the LR entry as it becomes
invalid. The next call to gic_get_lr_entry() will fail.
To overcome this issue, we call gic_activate_irq() before
gic_clear_pending(). This does not change the general behaviour of
gic_acknowledge_irq.
We also move the SGI case in gic_clear_pending_sgi() to enhance
code readability as the virtualization extensions support adds a if-else
level.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-12-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in gic_activate_irq() and
gic_drop_prio() and in gic_get_prio_from_apr_bits() called by
gic_drop_prio().
When the current CPU is a vCPU:
- Use GIC_VIRT_MIN_BPR and GIC_VIRT_NR_APRS instead of their non-virt
counterparts,
- the vCPU APR is stored in the virtual interface, in h_apr.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-11-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper functions to gic_internal.h to get or change the state
of an IRQ. When the current CPU is not a vCPU, the call is forwarded to
the GIC distributor. Otherwise, it acts on the list register matching
the IRQ in the current CPU virtual interface.
gic_clear_active can have a side effect on the distributor, even in the
vCPU case, when the correponding LR has the HW field set.
Use those functions in the CPU interface code path to prepare for the
vCPU interface implementation.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-10-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An access to the CPU interface is non-secure if the current GIC instance
implements the security extensions, and the memory access is actually
non-secure. Until then, it was checked with tests such as
if (s->security_extn && !attrs.secure) { ... }
in various places of the CPU interface code.
With the implementation of the virtualization extensions, those tests
must be updated to take into account whether we are in a vCPU interface
or not. This is because the exposed vCPU interface does not implement
security extensions.
This commits replaces all those tests with a call to the
gic_cpu_ns_access() function to check if the current access to the CPU
interface is non-secure. This function takes into account whether the
current CPU is a vCPU or not.
Note that this function is used only in the (v)CPU interface code path.
The distributor code path is left unchanged, as the distributor is not
exposed to vCPUs at all.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-9-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper macros and functions related to the virtualization
extensions to gic_internal.h.
The GICH_LR_* macros help extracting specific fields of a list register
value. The only tricky one is the priority field as only the MSB are
stored. The value must be shifted accordingly to obtain the correct
priority value.
gic_is_vcpu() and gic_get_vcpu_real_id() help with (v)CPU id manipulation
to abstract the fact that vCPU id are in the range
[ GIC_NCPU; (GIC_NCPU + num_cpu) [.
gic_lr_* and gic_virq_is_valid() help with the list registers.
gic_get_lr_entry() returns the LR entry for a given (vCPU, irq) pair. It
is meant to be used in contexts where we know for sure that the entry
exists, so we assert that entry is actually found, and the caller can
avoid the NULL check on the returned pointer.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-8-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the register definitions for the virtual interface of the GICv2.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-7-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary parts of the virtualization extensions state to the
GIC state. We choose to increase the size of the CPU interfaces state to
add space for the vCPU interfaces (the GIC_NCPU_VCPU macro). This way,
we'll be able to reuse most of the CPU interface code for the vCPUs.
The only exception is the APR value, which is stored in h_apr in the
virtual interface state for vCPUs. This is due to some complications
with the GIC VMState, for which we don't want to break backward
compatibility. APRs being stored in 2D arrays, increasing the second
dimension would lead to some ugly VMState description. To avoid
that, we keep it in h_apr for vCPUs.
The vCPUs are numbered from GIC_NCPU to (GIC_NCPU * 2) - 1. The
`gic_is_vcpu` function help to determine if a given CPU id correspond to
a physical CPU or a virtual one.
For the in-kernel KVM VGIC, since the exposed VGIC does not implement
the virtualization extensions, we report an error if the corresponding
property is set to true.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-6-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions are now only used in arm_gic.c, put them static. Some of
them where only used by the NVIC implementation and are not used
anymore, so remove them.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-4-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement GICD_ISACTIVERn and GICD_ICACTIVERn registers in the GICv2.
Those registers allow to set or clear the active state of an IRQ in the
distributor.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-3-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for the virtualization extensions implementation,
refactor the name of the functions and macros that act on the GIC
distributor to make that fact explicit. It will be useful to
differentiate them from the ones that will act on the virtual
interfaces.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The differences from ARMv7-M NVIC are:
* ARMv6-M only supports up to 32 external interrupts
(configurable feature already). The ICTR is reserved.
* Active Bit Register is reserved.
* ARMv6-M supports 4 priority levels against 256 in ARMv7-M.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Forbid stack alignment change. (CCR)
Reserve FAULTMASK, BASEPRI registers.
Report any fault as a HardFault. Disable MemManage, BusFault and
UsageFault, so they always escalated to HardFault. (SHCSR)
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180718095628.26442-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1.
All reserved registers are RAZ/WI. ARM_FEATURE_M_MAIN is used for the
checks, because these registers are reserved in ARMv8-M Baseline too.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code currently in gicv3_gicd_no_migration_shift_bug_post_load()
that handles migration from older QEMU versions with a particular
bug is misplaced. We need to run this after migration in all cases,
not just the cases where the "arm_gicv3/gicd_no_migration_shift_bug"
subsection is present, so it must go in a post_load hook for the
top level VMSD, not for the subsection. Move it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-6-peter.maydell@linaro.org
Contrary to the the impression given in docs/devel/migration.rst,
the migration code does not run the pre_load hook for a
subsection unless the subsection appears on the wire, and so
this is not a place where you can set the default value for
state for the "subsection not present" case. Instead this needs
to be done in a pre_load hook for whatever is the parent VMSD
of the subsection.
We got this wrong in two of the subsection definitions in
the GICv3 migration structs; fix this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-5-peter.maydell@linaro.org
Commit 6692aac411 accidentally introduced a second initialization
of the .subsections field of vmstate_gicv3_cpu, instead of adding
the new subsection to the existing list. The effect of this was
probably that migration of GICv3 with virtualization enabled was
broken (or alternatively that migration of ICC_SRE_EL1 was broken,
depending on which of the two initializers the compiler used).
Combine the two into a single list.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-3-peter.maydell@linaro.org
Currently the migration code incorrectly treats a subsection with
no .needed function pointer as if it was the subsection list
terminator -- it is ignored and so is everything after it.
Work around this by giving vmstate_gicv3_gicd_no_migration_shift_bug
a 'needed' function that always returns true.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-2-peter.maydell@linaro.org
The vmstate save/load code insists that subsections of a VMState must
have names which include their parent VMState's name as a leading
substring. Unfortunately it neither documents this nor checks it on
device init or state save, but instead fails state load with a
confusing error message ("Missing section footer for armv7m_nvic").
Fix the name of the m-security subsection of the NVIC, so that
state save/load works correctly for the security-enabled NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180727113854.20283-2-peter.maydell@linaro.org
When we escalate a v8M exception to HardFault, if AIRCR.BFHFNMINNS is
set then we need to decide whether it should become a secure HardFault
or a nonsecure HardFault. We should always escalate to the same
target security state as the original exception. The current code
tries to test this using the 'secure' bool, which is not right because
that flag indicates whether the target security state only for
banked exceptions; the effect was that we were incorrectly escalating
always-secure exceptions like SecureFault to a nonsecure HardFault.
Fix this by defining, logging and using a new 'targets_secure' bool
which tracks the condition we actually want.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180723123457.2038-1-peter.maydell@linaro.org
In icc_dir_write() we were incorrectly checking HCR_EL2.FMO
when determining whether IRQ should be routed to EL2; this should
be HCR_EL2.IMO (compare the GICv3 pseudocode ICC_DIR_EL1[]).
Use the correct mask.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180723180337.17378-1-peter.maydell@linaro.org
The instance_init function of the "exynos4210.gic" device creates a
new "arm_gic" device and immediately realizes it with qdev_init_nofail().
This will leave a lot of object in the QOM tree during introspection of
the "exynos4210.gic" device, e.g. reproducible by starting QEMU like this:
qemu-system-aarch64 -M none -nodefaults -nographic -monitor stdio
And then by running "info qom-tree" at the HMP monitor, followed by
"device_add exynos4210.gic,help" and finally checking "info qom-tree"
again.
Also note that qdev_init_nofail() can exit QEMU in case of errors - and
this must never happen during an instance_init function, otherwise QEMU
could terminate unexpectedly during introspection of a device.
Since most of the code that follows the qdev_init_nofail() depends on
the realized "gicbusdev", the easiest solution to the problem is to
turn the whole instance_init function into a realize function instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1532337784-334-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU currently crashes when introspecting the "iotkit" device and
runnint "info qtree" afterwards, e.g. when running QEMU like this:
echo "{'execute':'qmp_capabilities'} {'execute':'device-list-properties'," \
"'arguments':{'typename':'iotkit'}}" "{'execute': 'human-monitor-command', " \
"'arguments': {'command-line': 'info qtree'}}" | \
aarch64-softmmu/qemu-system-aarch64 -M none,accel=qtest -qmp stdio
Use the new functions object_initialize_child() and sysbus_init_child_obj()
to make sure that all objects get cleaned up correctly when the instances
are destroyed.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1531745974-17187-5-git-send-email-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ITARGETSR implementation still has some 11MPCore behaviour
that we were incorrectly using in our GICv1 and GICv2 implementations
for the case where the interrupt number is less than GIC_INTERNAL.
The desired behaviour here is:
* for 11MPCore: RAZ/WI for irqs 0..28; read a number matching the
CPU doing the read for irqs 29..31
* for GICv1 and v2: RAZ/WI if uniprocessor; otherwise read a
number matching the CPU doing the read for all irqs < 32
Stop squashing GICD_ITARGETSR to 0 for IRQs 0..28 unless this
is an 11MPCore GIC.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-3-peter.maydell@linaro.org
In gic_deactivate_irq() the interrupt number comes from the guest
(on a write to the GICC_DIR register), so we need to sanity check
that it isn't out of range before we use it as an array index.
Handle this in a similar manner to the check we do in
gic_complete_irq() for the GICC_EOI register.
The array overrun is not disastrous because the calling code
uses (value & 0x3ff) to extract the interrupt field, so the
only out-of-range values possible are 1020..1023, which allow
overrunning only from irq_state[] into the following
irq_target[] array which the guest can already manipulate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-2-peter.maydell@linaro.org
Recent cleanup in commit a028dd423e dropped the ICPStateClass::reset
handler. It is now up to child ICP classes to call the DeviceClass::reset
handler of the parent class, thanks to device_class_set_parent_reset().
This is a better object programming pattern, but unfortunately it causes
QEMU to crash during CPU hotplug:
(qemu) device_add host-spapr-cpu-core,id=core1,core-id=1
Segmentation fault (core dumped)
When the hotplug path tries to reset the ICP device, we end up calling:
static void icp_kvm_reset(DeviceState *dev)
{
ICPStateClass *icpc = ICP_GET_CLASS(dev);
icpc->parent_reset(dev);
but icpc->parent_reset is NULL... This happens because icp_kvm_class_init()
calls:
device_class_set_parent_reset(dc, icp_kvm_reset,
&icpc->parent_reset);
but dc->reset, ie, DeviceClass::reset for the TYPE_ICP type, is
itself NULL.
This patch hence sets DeviceClass::reset for the TYPE_ICP type to
point to icp_reset(). It then registers a reset handler that calls
DeviceClass::reset. If the ICP subtype has configured its own reset
handler with device_class_set_parent_reset(), this ensures it will
be called first and it can then call ICPStateClass::parent_reset
safely. This fixes the reset path for the TYPE_KVM_ICP type, which
is the only subtype that defines its own reset function.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Fixes: a028dd423e
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The vector cannot be negative. Coverity now reports this because it sees an
array access before the check, in ioapic_stat_update_irq.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the previous changes, we can now let the ICS_KVM class inherit
directly from ICS_BASE class and not from the intermediate ICS_SIMPLE.
It makes the class hierarchy much cleaner.
What is left in the top classes is the low level interface to access
the KVM XICS device in ICS_KVM and the XICS emulating handlers in
ICS_SIMPLE.
This should not break migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Just like for the realize handlers, this makes possible to move the
common ICSState code of the reset handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes possible to move the common ICSState code of the realize
handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This changes the ICP realize and reset handlers in DeviceRealize and
DeviceReset handlers. parent handlers are now called from the
inheriting classes which is a cleaner object pattern.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This include both userspace and in-kernel ioapic. Note that the numbers
can be inaccurate for kvm-ioapic. One reason is the same with
kvm-i8259, that when irqfd is used, irqs can be delivered all inside
kernel without our notice. Meanwhile, kvm-ioapic is specially treated
when irq numbers <ISA_NUM_IRQS, those irqs will be delivered in kernel
too via kvm-i8259 (please refer to kvm_pc_gsi_handler).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So that now it looks better when with other irqchips.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
People start to use "info pic" for all kinds of irqchip dumps. Let x86
ioapic join the family. It dumps the same thing as "info ioapic".
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-3-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's check if KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION is supported.
If not, we check the number of redist region is equal to 1 and use the
legacy KVM_VGIC_V3_ADDR_TYPE_REDIST attribute. Otherwise we use
the new attribute and allow to register multiple regions to the
KVM device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
for KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION attribute, the attribute
data pointed to by kvm_device_attr.addr is a OR of the
redistributor region address and other fields such as the index
of the redistributor region and the number of redistributors the
region can contain.
The existing machine init done notifier framework sets the address
field to the actual address of the device and does not allow to OR
this value with other fields.
This patch extends the KVMDevice struct with a new kda_addr_ormask
member. Its value is passed at registration time and OR'ed with the
resolved address on kvm_arm_set_device_addr().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529072910-16156-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When either GICD_IPRIORITYR or GICR_IPRIORITYR is read as a 32-bit
register, the post left-shift operator in the for loop causes an
extra shift after the least significant byte has been placed.
The 32-bit value actually returned is therefore the expected value
shifted left by 8 bits.
Signed-off-by: Amol Surati <suratiamol@gmail.com>
Message-id: 20180614054857.26248-1-suratiamol@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On CentOS 7.5, gcc-4.8.5-28.el7_5.1.ppc64le fails to build QEMU due to :
hw/intc/xics_kvm.c: In function ‘ics_set_kvm_state’:
hw/intc/xics_kvm.c:281:13: error: ‘ret’ may be used uninitialized in this
function [-Werror=maybe-uninitialized]
return ret;
Fix the breakage and also remove the extra error reporting as
kvm_device_access() already provides a substantial error message.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Cortex-M CPU and its NVIC are two intimately intertwined parts of
the same hardware; it is not possible to use one without the other.
Unfortunately a lot of our board models don't do any sanity checking
on the CPU type the user asks for, so a command line like
qemu-system-arm -M versatilepb -cpu cortex-m3
will create an M3 without an NVIC, and coredump immediately.
In the other direction, trying a non-M-profile CPU in an M-profile
board won't blow up, but doesn't do anything useful either:
qemu-system-arm -M lm3s6965evb -cpu arm926
Add some checking in the NVIC and CPU realize functions that the
user isn't trying to use an NVIC without an M-profile CPU or
an M-profile CPU without an NVIC, so we can produce a helpful
error message rather than a core dump.
Fixes: https://bugs.launchpad.net/qemu/+bug/1766896
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601160355.15393-1-peter.maydell@linaro.org
While for_each_dist_irq_reg loop starts from GIC_INTERNAL, it forgot to
offset the date array and index. This will overlap the GICR registers
value and leave the last GIC_INTERNAL irq's registers out of update.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The KVM helpers hide the low level interface used to communicate to
the XICS KVM device and provide a good cleanup to the XICS KVM models.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While we skip the GIC_INTERNAL irqs, we don't change the register offset
accordingly. This will overlap the GICR registers value and leave the
last GIC_INTERNAL irq's registers out of update.
Fix this by skipping the registers banked by GICR.
Also for migration compatibility if the migration source (old version
qemu) doesn't send gicd_no_migration_shift_bug = 1 to destination, then
we shift the data of PPI to get the right data for SPI.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1527816987-16108-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include files shouldn't have the "include/" part, that is implied.
Also, drop an unused include.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
kvm_irqchip_create called by kvm_init will call kvm_init_irq_routing to
initialize global capability variables. If we call kvm_init_irq_routing in
GIC realize function, previous allocated memory will leak.
Fix this by deleting the unnecessary call.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527750994-14360-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It forgot to increase clroffset during the loop. So it only clear the
first 4 bytes.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527047633-12368-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There was a nasty flip in identifying which register group an access is
targeting. The issue caused spuriously raised priorities of the guest
when handing CPUs over in the Jailhouse hypervisor.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-id: 28b927d3-da58-bce4-cc13-bfec7f9b1cb9@siemens.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This eliminates the need for fetching it from el_change_hook_opaque, and
allows for supporting multiple el_change_hooks without having to hack
something together to find the registered opaque belonging to GICv3.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1523997485-1905-6-git-send-email-alindsay@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the GIC has the security extension support enabled, then a
non-secure access to ICC_PMR must take account of the non-secure
view of interrupt priorities, where real priorities 0x00..0x7f
are secure-only and not visible to the non-secure guest, and
priorities 0x80..0xff are shown to the guest as if they were
0x00..0xff. We had the logic here wrong:
* on reads, the priority is in the secure range if bit 7
is clear, not if it is set
* on writes, we want to set bit 7, not mask everything else
Our ICC_RPR read code had the same error as ICC_PMR.
(Compare the GICv3 spec pseudocode functions ICC_RPR_EL1
and ICC_PMR_EL1.)
Fixes: https://bugs.launchpad.net/qemu/+bug/1748434
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180315133441.24149-1-peter.maydell@linaro.org
The MemoryListener is registered on address_space_memory, there is
not much to assert. This currently works because the callback
is invoked only once when the listener is registered, but section->fv
is the _new_ FlatView, not the old one on later calls and that
would break.
This confines address_space_to_flatview to exec.c and memory.c.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is to faciliate access to OpenPICState when wiring up the PIC to the macio
controller.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is needed before the next patch because the target-dependent kvm stub
uses the existing kvm_openpic_connect_vcpu() declaration, making it impossible
to move the device-specific declarations into the same file without breaking
ppc-linux-user compilation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the device to be made available during the setup of the Old World
machine. In order to pass back the previous set of IRQs we temporarily introduce
a new pic_irqs parameter until it can be removed.
An additional benefit of this change is that it is also possible to remove the
pic_mem pointer used for macio by accessing the memory region via sysbus.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Presently s390x is the only architecture not exposing specific
CPU information via QMP query-cpus. Upstream discussion has shown
that it could make sense to report the architecture specific CPU
state, e.g. to detect that a CPU has been stopped.
With this change the output of query-cpus will look like this on
s390:
[
{"arch": "s390", "current": true,
"props": {"core-id": 0}, "cpu-state": "operating", "CPU": 0,
"qom_path": "/machine/unattached/device[0]",
"halted": false, "thread_id": 63115},
{"arch": "s390", "current": false,
"props": {"core-id": 1}, "cpu-state": "stopped", "CPU": 1,
"qom_path": "/machine/unattached/device[1]",
"halted": true, "thread_id": 63116}
]
This change doesn't add the s390-specific data to HMP 'info cpus'.
A follow-on patch will remove all architecture specific information
from there.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1518797321-28356-2-git-send-email-mihajlov@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In many of the NVIC registers relating to interrupts, we
have to convert from a byte offset within a register set
into the number of the first interrupt which is affected.
We were getting this wrong for:
* reads of NVIC_ISPR<n>, NVIC_ISER<n>, NVIC_ICPR<n>, NVIC_ICER<n>,
NVIC_IABR<n> -- in all these cases we were missing the "* 8"
needed to convert from the byte offset to the interrupt number
(since all these registers use one bit per interrupt)
* writes of NVIC_IPR<n> had the opposite problem of a spurious
"* 8" (since these registers use one byte per interrupt)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180209165810.6668-9-peter.maydell@linaro.org
We were previously making the system control register (SCR)
just RAZ/WI. Although we don't implement the functionality
this register controls, we should at least provide the state,
including the banked state for v8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-7-peter.maydell@linaro.org
M profile cores have a similar setup for cache ID registers
to A profile:
* Cache Level ID Register (CLIDR) is a fixed value
* Cache Type Register (CTR) is a fixed value
* Cache Size ID Registers (CCSIDR) are a bank of registers;
which one you see is selected by the Cache Size Selection
Register (CSSELR)
The only difference is that they're in the NVIC memory mapped
register space rather than being coprocessor registers.
Implement the M profile view of them.
Since neither Cortex-M3 nor Cortex-M4 implement caches,
we don't need to update their init functions and can leave
the ctr/clidr/ccsidr[] fields in their ARMCPU structs at zero.
Newer cores (like the Cortex-M33) will want to be able to
set these ID registers to non-zero values, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-6-peter.maydell@linaro.org
The Coprocessor Power Control Register (CPPWR) is new in v8M.
It allows software to control whether coprocessors are allowed
to power down and lose their state. QEMU doesn't have any
notion of power control, so we choose the IMPDEF option of
making the whole register RAZ/WI (indicating that no coprocessors
can ever power down and lose state).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-5-peter.maydell@linaro.org
For M profile cores, cache maintenance operations are done by
writing to special registers in the system register space.
For QEMU, cache operations are always NOPs, since we don't
implement the cache. Implementing these explicitly avoids
a spurious LOG_GUEST_ERROR when the guest uses them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-4-peter.maydell@linaro.org
The PENDNMISET/CLR bits in the ICSR should be RAZ/WI from
NonSecure state if the AIRCR.BFHFNMINS bit is zero. We had
misimplemented this as making the bits RAZ/WI from both
Secure and NonSecure states. Fix this bug by checking
attrs.secure so that Secure code can pend and unpend NMIs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-3-peter.maydell@linaro.org
Instead of hardcoding the values of M profile ID registers in the
NVIC, use the fields in the CPU struct. This will allow us to
give different M profile CPU types different ID register values.
This commit includes the addition of the missing ID_ISAR5,
which exists as RES0 in both v7M and v8M.
(The values of the ID registers might be wrong for the M4 --
this commit leaves the behaviour there unchanged.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-2-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Support M profile derived exceptions on exception entry and exit
* Implement AArch64 v8.2 crypto insns (SHA-512, SHA-3, SM3, SM4)
* Implement working i.MX6 SD controller
* Various devices preparatory to i.MX7 support
* Preparatory patches for SVE emulation
* v8M: Fix bug in implementation of 'TT' insn
* Give useful error if user tries to use userspace GICv3 with KVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bokK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180209' into staging
target-arm queue:
* Support M profile derived exceptions on exception entry and exit
* Implement AArch64 v8.2 crypto insns (SHA-512, SHA-3, SM3, SM4)
* Implement working i.MX6 SD controller
* Various devices preparatory to i.MX7 support
* Preparatory patches for SVE emulation
* v8M: Fix bug in implementation of 'TT' insn
* Give useful error if user tries to use userspace GICv3 with KVM
# gpg: Signature made Fri 09 Feb 2018 11:01:23 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180209: (30 commits)
hw/core/generic-loader: Allow PC to be set on command line
target/arm/translate.c: Fix missing 'break' for TT insns
target/arm/kvm: gic: Prevent creating userspace GICv3 with KVM
target/arm: Add SVE state to TB->FLAGS
target/arm: Add ZCR_ELx
target/arm: Add SVE to migration state
target/arm: Add predicate registers for SVE
target/arm: Expand vector registers for SVE
hw/arm: Move virt's PSCI DT fixup code to arm/boot.c
usb: Add basic code to emulate Chipidea USB IP
i.MX: Add implementation of i.MX7 GPR IP block
i.MX: Add i.MX7 GPT variant
i.MX: Add code to emulate GPCv2 IP block
i.MX: Add code to emulate i.MX7 SNVS IP-block
i.MX: Add code to emulate i.MX2 watchdog IP block
i.MX: Add code to emulate i.MX7 CCM, PMU and ANALOG IP blocks
hw: i.MX: Convert i.MX6 to use TYPE_IMX_USDHC
sdhci: Add i.MX specific subtype of SDHCI
target/arm: enable user-mode SHA-3, SM3, SM4 and SHA-512 instruction support
target/arm: implement SM4 instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently armv7m_nvic_acknowledge_irq() does three things:
* make the current highest priority pending interrupt active
* return a bool indicating whether that interrupt is targeting
Secure or NonSecure state
* implicitly tell the caller which is the highest priority
pending interrupt by setting env->v7m.exception
We need to split these jobs, because v7m_exception_taken()
needs to know whether the pending interrupt targets Secure so
it can choose to stack callee-saves registers or not, but it
must not make the interrupt active until after it has done
that stacking, in case the stacking causes a derived exception.
Similarly, it needs to know the number of the pending interrupt
so it can read the correct vector table entry before the
interrupt is made active, because vector table reads might
also cause a derived exception.
Create a new armv7m_nvic_get_pending_irq_info() function which simply
returns information about the highest priority pending interrupt, and
use it to rearrange the v7m_exception_taken() code so we don't
acknowledge the exception until we've done all the things which could
possibly cause a derived exception.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1517324542-6607-3-git-send-email-peter.maydell@linaro.org
In order to support derived exceptions (exceptions generated in
the course of trying to take an exception), we need to be able
to handle prioritizing whether to take the original exception
or the derived exception.
We do this by introducing a new function
armv7m_nvic_set_pending_derived() which the exception-taking code in
helper.c will call when a derived exception occurs. Derived
exceptions are dealt with mostly like normal pending exceptions, so
we share the implementation with the armv7m_nvic_set_pending()
function.
Note that the way we structure this is significantly different
from the v8M Arm ARM pseudocode: that does all the prioritization
logic in the DerivedLateArrival() function, whereas we choose to
let the existing "identify highest priority exception" logic
do the prioritization for us. The effect is the same, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1517324542-6607-2-git-send-email-peter.maydell@linaro.org
This avoids tons of conversions when handling interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-19-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This avoids tons of conversions when handling interrupts.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This avoids tons of conversions when handling interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Kicking all CPUs on every floating interrupt is far from efficient.
Let's optimize it at least a little bit.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-12-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that we have access to the io interrupts, we can implement
clear_io_irq() for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-11-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Move floating interrupt handling into the flic. Floating interrupts
will now be considered by all CPUs, not just CPU #0. While at it, convert
I/O interrupts to use a list and make sure we properly consider I/O
sub-classes in s390_cpu_has_io_int().
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-9-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We can directly call the right function.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-7-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let the flic device handle it internally. This will allow us to later
on store floating interrupts in the flic for the TCG case.
This now also simplifies kvm.c. All that's left is the fallback
interface for floating interrupts, which is now triggered directly via
the flic in case anything goes wrong.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We can simply search for an object of our common type.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This makes it clearer, which device is used for which accelerator.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is the initial version of the Inter Processor Interrupt device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Add the PMU IO Module Interrupt controller device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aF9Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180125' into staging
target-arm queue:
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
# gpg: Signature made Thu 25 Jan 2018 12:59:25 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180125: (21 commits)
pl110: Implement vertical compare/next base interrupts
xilinx_spips: Correct usage of an uninitialized local variable
sdhci: fix a NULL pointer dereference due to uninitialized AddresSpace object
hw/arm/virt: Check that the CPU realize method succeeded
hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
hw/intc/arm_gic: Fix C_RPR value on idle priority
hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
target/arm: Simplify fp_exception_el for user-only
target/arm: Hoist store to flags output in cpu_get_tb_cpu_state
target/arm: Move cpu_get_tb_cpu_state out of line
target/arm: Add ARM_FEATURE_SVE
vmstate: Add VMSTATE_UINT64_SUB_ARRAY
target/arm: Add aa{32, 64}_vfp_{dreg, qreg} helpers
target/arm: Change the type of vfp.regs
target/arm: Use pointers in neon tbl helper
target/arm: Use pointers in neon zip/uzp helpers
target/arm: Use pointers in crypto helpers
target/arm: Mark disas_set_insn_syndrome inline
i.MX: Fix FEC/ENET receive funtions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When C_CTRL.CBPR is 1, the Non-Secure view of C_BPR is altered:
- A Non-Secure read of C_BPR should return the BPR value plus 1,
saturated to 7,
- A Non-Secure write should be ignored.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-6-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment typo]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When determining the group priority of a group 1 IRQ, if C_CTRL.CBPR is
0, the non-secure BPR value is used. However, this value must be
incremented by one so that it matches the secure world number of
implemented priority bits (NS world has one less priority bit compared
to the Secure world).
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-5-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: add assert, as the gicv3 code has]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When there is no active interrupts in the GIC, a read to the C_RPR
register should return the value of the "Idle priority", which is either
the maximum value an IRQ priority field can be set to, or 0xff.
Since the QEMU GIC model implements all the 8 priority bits, the Idle
priority is 0xff.
Internally, when there is no active interrupt, the running priority
value is 0x100. The gic_get_running_priority function returns an uint8_t
and thus, truncate this value to 0x00 when returning it. This is wrong since
a value of 0x00 correspond to the maximum possible priority.
This commit fixes the returned value when the internal value is 0x100.
Note that it is correct for the Non-Secure view to return 0xff even
though from the NS world point of view, only 7 priority bits are
implemented. The specification states that the Idle priority can be 0xff
even when not all the 8 priority bits are implemented. This has been
verified against a real GICv2 hardware on a Xilinx ZynqMP based board.
Regarding the ARM11MPCore version of the GIC, the specification is not
clear on that point, so this commit does not alter its behavior.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-4-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the GIC, when an IRQ is acknowledged, its state goes from "pending"
to:
- "active" if the corresponding IRQ pin has been de-asserted
- "active and pending" otherwise.
The GICv2 manual states that when a IRQ becomes active (or active and
pending), the GIC should either signal another (higher priority) IRQ to
the CPU if there is one, or de-assert the CPU IRQ pin.
The current implementation of the GIC in QEMU does not check if the
IRQ is already active when looking for pending interrupts with
sufficient priority in gic_update(). This can lead to signaling an
interrupt that is already active.
This usually happens when splitting priority drop and interrupt
deactivation. On priority drop, the IRQ stays active until deactivation.
If it becomes pending again, chances are that it will be incorrectly
selected as best_irq in gic_update().
This commit fixes this by checking if the IRQ is not already active when
looking for best_irq in gic_update().
Note that regarding the ARM11MPCore GIC version, the corresponding
manual is not clear on that point, but it has has no priority
drop/interrupt deactivation separation, so this case should not happen.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-3-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the LEON3 IRQ controller IRQs can be acknowledged 2 ways:
* Explicitly by software writing to the CLEAR_OFFSET register
* Implicitly when the procesor is done running the trap handler attached
to the IRQ.
The actual IRQMP code only allows the implicit processor triggered IRQ ack.
If software write explicitly to the CLEAR_OFFSET register, this will clear
the pending bit in the register value but this will not lower the ongoing
raised IRQ with the processor. The IRQ will be kept raised to the LEON
processor until the related trap handler is run and the processor implicitly
ack the interrupt. So with the actual IRQMP code trap handler have to be run
even if the software has already done its job by clearing the pending bit.
This feature has been tested on another LEON3 simulator (tsim_leon3 from
Gaisler) and it turns out that the Qemu implementation is not equivalent to
the tsim one. In tsim, if software does clear a pending interrupt before
the related interrupt handler is triggered the said interrupt handler will
not be called.
This patch brings the Qemu IRQMP implementation in line with the tsim
implementation by allowing IRQ to be acknowledged by software only.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Configurable Fault Status Register for ARMv7M and v8M is
supposed to be byte and halfword accessible, but we were only
implementing word accesses. Add support for the other access
sizes, which are used by the Zephyr RTOS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512742372-31517-1-git-send-email-peter.maydell@linaro.org
The GICv2 specification says that reserved register addresses
must RAZ/WI; now that we implement external abort handling
for Arm CPUs this means we must return MEMTX_OK rather than
MEMTX_ERROR, to avoid generating a spurious guest data abort.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
The GICv3 specification says that reserved register addresses
should RAZ/WI. This means we need to return MEMTX_OK, not MEMTX_ERROR,
because now that we support generating external aborts the
latter will cause an abort on new board models.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This patch adds the function apic_get_highest_priority_irr to
apic.c and exports it through the interface in apic.h for use by hvf.
Signed-off-by: Sergio Andres Gomez Del Real <Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-8-Sergio.G.DelReal@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now both classes (i8259, i8259-kvm) support this. Move this upper to
the common class code.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-6-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's leverage the i8259 common code for kvm-i8259 too.
I think it's still possible that stats can lost when i8259 is in kernel
and meanwhile when irqfd is used, e.g., by vfio or vhost devices.
However that should be rare IMHO since they should be using MSIs mostly
if they really want performance (that's why people use vhost and device
assignment), and no old INTx should be used. As long as the INTx users
are emulated in QEMU the stats will be correct.
For "info pic", it should be always accurate since we fetch kvm regs
before dump.
More importantly, it's just too simple to do this now - it's only 10+
LOC to gain this feature.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-5-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was only for userspace i8259. Move it to general code so that
kvm-i8259 can also use it in the future.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's not really scary to even enable it forever. After all it's i8259,
and it's even not the kernel one.
Then we can remove quite a few of lines to make it cleaner. And "info
irq" will always work for it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One thing to mention is that in pic_set_irq() I need to uncomment a few
lines in the macros to make sure IRQ value calculation is correct.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-2-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xics_get_qirq() is only used by the sPAPR machine. Let's move it there
and change its name to reflect its scope. It will be useful for XIVE
support which will use its own set of qirqs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the prototype to use a sPAPRMachineState and prefix them
with spapr_irq_. It will let us synchronise the IRQ allocation with
the XIVE interrupt mode when available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'intc' pointer of the CPU references the interrupt presenter in
the XICS interrupt mode. When the XIVE interrupt mode is available and
activated, the machine will need to reassign this pointer to reflect
the change.
Moving this assignment under the realize routine of the CPU will ease
the process when the interrupt mode is toggled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR and the PowerNV core objects create the interrupt presenter
object of the CPUs in a very similar way. Let's provide a common
routine in which we use the presenter 'type' as a child identifier.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace *printf() with *_report().
Remove trailing new lines.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The previous code section uses a 'first < 0' test and returns. Therefore,
there is no need to test the 'first' variable against '>= 0' afterwards.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the v8M security extension, there should be two systick
devices, which use separate banked systick exceptions. The
register interface is banked in the same way as for other
banked registers, including the existence of an NS alias
region for secure code to access the nonsecure timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-3-git-send-email-peter.maydell@linaro.org
Generalize nvic_sysreg_ns_ops so that we can pass it an
arbitrary MemoryRegion which it will use as the underlying
register implementation to apply the NS-alias behaviour
to. We'll want this so we can do the same with systick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-2-git-send-email-peter.maydell@linaro.org
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
