the historical link? flags for media select)
XXX No pullup request for this. But if sysinst supports explicit media
XXX selection in 1.3, this should be in 1.3 as well.
clobbers my SMC. Now I can really use a generic kernel with my SMC @0x300.
This change has been tested on various machines with ne2000 and 3c509 baords.
XXX All these probes sould be reordered after the release, with invasive
XXX probes at the end.
to look specifically at the address it was provided *only*, since the
scan isn't safe (it can stomp on cards that will be probed later, like
NE2000 clones).
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
Supports changing media with ifconfig's "media" directive.
This splits the 3c503 functionality out of the ISA "ed" driver, much the
same way NE2000 support was split out.
intr_alloc_mask) into one place, comment them, and defopt them.
- Rename pcic_intr_alloc_mask to pcic_isa_intr_alloc_mask, since it's
an ISA-specific thing.
- When allocating/establishing the PCIC's interrupt (for card events),
do error checking, and pay attention to the intr_alloc_mask.
for the built-in SCSI on NEC Versa docking stations, and if a card
allocates that IRQ, it will never get interrupts. This caused the
default kernel to not work on these laptops, as IRQ 10 was often the
first free IRQ.
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Also, fix the scb freelist fencepost, like the aha/bha/uha drivers.
- at end of attach, explicitely select an existing drive. This fixes hangs
some users reported (such as the one reported in port-i386/4247).
- Some atapi cdrom drives (e.g. Nec 24x) don't enables their registers before
a controller reset is issued. The controller probe routine is changed as
follow: issue a controller reset. If fail, test atapi signature on slave.
If fail, wait 5s and retry a reset. If the second reset fail, return(0).
If the first reset succeed, test presence of a master drive:
atapi signature, and if this fail RO/RW registers test. If no master, test
atapi signature on slave. If no slave, return 0.
Instead, print a diagnostic and return. (Some drivers do this already.)
Also, normalize the diagnostic message, and fix some places where the
printfs were getting ugly.
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
The isa attachment code is in isa/lpt_isa.c now, which attaches to the
already created ic/lpt* files.
You don't need to change your config files, but you need to re-"config" if
using lpt at isa.
XXX The "lpt" device definition should be in sys/conf/files instead, but to
my knowledge, there are some ports which have private copies of lpt, and would
choke on that. No need to make people unhappy 7 days before release branching.
pseudo-device rnd # /dev/random and in-kernel generator
in config files.
o Add declaration to all architectures.
o Clean up copyright message in rnd.c, rnd.h, and rndpool.c to include
that this code is derived in part from Ted Tyso's linux code.
* support chip clocks != COM_FREQ, by introducing sc_frequency (for the
mainline code) and adding a frequency parameter right after the rate
parameter to comcnattach() and com_kgdb_attach().
- Make com_isa and com_multi initialize sc_frequency to COM_FREQ.
- Make i386/machdep.c and alpha/dec_xxx.c call com*attach() with the freq.
parameter.
* supio_attach_args get two more fields: a sc_ipl and a sc_arg, both ints.
- com_supio uses the first for interupt establishment (all childs will, as
soon as they exist) and the 2nd for sc_frequency.
- drsupio passes sc_ipl alway as 5, and for the "com"s, sc_arg as 16*115200
- hyper will pass sc_ipl as 6, and sc_arg as 16 * 460800
be probed several times. This fixes the "ATAPI CD probed as wd drive" problem.
Thanks to Geoff Wing <mason@primenet.com.au> for testing this on his hardware.
I also made inclusion of LPRINTF() dependent solely on the symbol
LPTDEBUG, initialized lptdebug variable to 0 instead of 1, and
matched arguments to format strings in LPRINTF() calls.
Because of the braindead design of the SB the input and output have to
use different precisions (8 and 16 bits). It is possible to set the driver
to use 8 bits on both and it will the emulate 8 bits on the output by
expanding it to 16 bits.
looking what's the autoconfig do on strange harware, and ATAPI_DEBUG2 is
for debuging data transfers (and is really verbose once the machine has booted
from an IDE disk).
(currently only CD-ROM drives on i386). The sys/dev/scsipi system provides 2
busses to which devices can attach (scsibus and atapibus). This needed to
change some include files and structure names in the low level scsi drivers.
two DMA channels to do e.g. full-duplex. This allows
a way of specifying the second channel in a sane way.
THIS IS TEMPORARY. The drq2 locator will go away when
the locator system has been changed to allow multiple
values per locator.
at the same time instead by using two different calls. This enables
it to check more easily if the combined mode is all right.
- Improve the error checking in audio.c.
- Add a new audio property, AUDIO_PROP_INDEPENDENT, show if the
play and record settings are independent.
- Fix some buglets in audio.c.
-put all early console / KGDB initialization into 1 exported function
(com_*_attach()) each, dont use global variables anymore
-use the passed tcflag_t for port settings instead of hardwiring 8N1
-at autoconfiguration attach time, decide if the attaching device is
already console / KGDB by comparing bus tag and base addr (cgd's wish)
-export a function "com_is_console()" for use by driver frontends for
this comparision
-delay setting of cn_tab->cn_dev until autoconfiguration attach
to get the minor number right
-delete unused comcnprobe() and comcninit()
-Separate KGDB port initialization and softc related stuff to allow
KGDB to be attached in early system startup, before autoconfiguration.
-Export the variables needed by md code to hand-craft bus tag/handle.
-Fix initialization to enable interrupt by line break.
-Call DDB/KGDB at line break (move DDB call from the softirq handler
to the hard handler because it should work without a tty attached too).
* Make it possible to use software assisted encodings that expand the
sample size.
* Use 16 bits per sample when emulating mulaw coding on the SB.
* Prepare for SB16 without CT1745 mixer.
- Change the way attach and open works to allow multiple audio
devices.
- Split the mulaw.c file into two to avoid dragging in mulaw
convertsion when they are not needed. Add 16 bit alaw/mulaw tables.
- Change the way audio properties are gotten.
- Recognize more versions os SoundBlaster.
- It is now possible to handle devices that want "looping" DMA,
e.g. the SoundBlaster correctly. The WSS and SB drivers use this.
To do this several new methods were introduced in audio_hw_if.
- Different silence handling (forced by previous change).
- The audio driver can now be mmap()-ed, but due to problems in
the VM system only for writing for now.
- The OSS (Linux) audio emulation takes advantage of some of the
new features.
renamed AUDIO_ENCODING_SLINEAR and AUDIO_ENCODING_LINEAR reverts to the
NetBSD 1.2 sematics. A kernel with COMPAT_12 defined will accept
AUDIO_ENCODING_LINEAR and treat it as before, without COMPAT_12 it
will be rejected.
cast if it isn't. (These casts aren't necessarily safe, because of
alignment issues, but they allow the code to compile with prototyped versions
of bus_space_{read,write}_multi_2().)
mark mulaw as emulated (it's done via a mapping table)
use GUS query encoding routine, even on GUS max, since the encoding
stuff is handled by the GF1.
XXX might not be right for recording, but it's correct for playback.
Set the encoding parameters slightly differently.
Remove the SW encoding/decodinf functions from this interface
and move them to the audio_parameter struct; this is both more efficient
and flexible.
Some of the stuff (e.g., rarpd, bootpd, dhcpd etc., libsa) still will
only support Ethernet. Tcpdump itself should be ok, but libpcap needs
lot of work.
For the detailed change history, look at the commit log entries for
the is-newarp branch.
to prepare for if_media, and to support EISA 3c59x cards:
* change epconfig() to take a short that encodes the chipset
type (3c509, or Demon/Vortex/Boomerang).
* add distinct 3c509 and Demon/Vortex/Boomerang media-sense
functions to back end.
* Add EISA match/attach support for the 3c592 and 3c597
(Demon) cards as well as the 3c509-comatibl EISA 3c509/3c579.
* Assume that ISA and ISA PnP cards are 3c509-style, until
proof to the contrary (e.g. large packet support).
Tested on 3c595, 3c590, and 3c509b. Not tested on 3c515 or Demon.
isascan (__BROKEN_INDIRECT_CONFIG), and attempt multiple match/attach
of cloning devices in isasearch(). (If a match/attach succeeds for
a cloning device, try it again.)
(e.g. from 0x3bc to 0x3bf, for example). Others may require more,
but until there's some special handling for them, 4 should be returned
so that on systems with I/O port accounting, the unit at 0x3bf can be
properly mapped, etc. (OK'd by mycroft.)
devices actually do make sense on indirect-config busses, because you
might be able to have more than one of the busses! In addition, they're
useful because they don't require unit numbers to be wired down, so you
could e.g. have vga* at indirect? and vga* at direct?, and have the first
one found be unit number zero. Finally, devices which can divine their
own ports numbers, etc., actually should be cloning, even if you know you'll
only have one bus that they can live on.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
prototypes, and suppress a bogus "might be used uninitialized" warning.
It's clear from reading the logic of the function that produces the
warning that the variable will not be used uninitialized, but the
compiler just isn't smart enough, I guess. Marked XXX for future reference.
multi-channel driver), or to SCSI_CHANNEL_ONLY_ONE if a
single-channel driver.
(2) use scsiprint() rather than a locally-defined autoconfig print
function, and kill any locally-defined print function.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
- In egstart(), if the Send Packet command fails, m_freem()
the mbuf chain before dequeueing another one (memory leak).
- In egintr(), return 1 if a known interrupt was processed.
Would manifest itself as spurious interrupts.
device and a printable "external name" (name + unit number), thus eliminating
if_name and if_unit. Updated interface to (*if_watchdog)() and (*if_reset)()
to take a struct ifnet *, rather than a unit number.
naming conflicts between bus attachments on ports that can have
multiple instances of the LANCE.
Break up ISA LANCE driver into ISA and PCI front-ends.
Changed struct ifnet to have a pointer to the softc of the underlying
device and a printable "external name" (name + unit number), thus eliminating
if_name and if_unit. Updated interface to (*if_watchdog)() and (*if_start)()
to take a struct ifnet *, rather than a unit number.
(and only tested on) Intel Etherexpress PRO. Should work on any i82595 ISA
board which uses an EEPROM for config information; NETBLKID not yet supported.
TODO: change to BUS interface, add multicast support.
Use the i/o handle for the `delay port' exported from the parent
ISA bus, rather than the totally bogus combination of [ioh, 0x84].
Also, fix a bug apparently introduced when the -Wall changes were checked
in which, under most circumstances, would cause a 16-bit WD8013EP to
be mis-identified as an 8-bit WD8003EP.
For the ISA probe, implement a way to keep track of which ISA busses
have been through an ep_isa probe; the static variable that was used
before didn't scale.
In elink_reset(), since some machines may have more than one ISA bus,
implement a way of keeping track of which ISA bus has received an
elink_reset(); The static variable which was used previously didn't
scale.
bus-independent core driver. Tested on all three bus types, including
an isa 3c509 masquerading as an eisa device (use ep* at eisa? slot ? in
your kernel config file to catch this one).
XXX Driver still needs to be converted to <machine/bus.h>
remove their 'integrate' (usually defined to be 'static') keywords.
when lance drivers are split up by attachment, more than one file will
reference the copy/zero functions (i.e. not just the file that pulls in
am7990.c... and eventually inclusion of am7990.c should go away entirely).
'cflag' for the console. Normally set to TTYDEF_CFLAG, may be
overridden by machine-dependent console attachment code, as necessary.
(Alpha uses it to set cs8 -parenb.) Files including comvar.h now
need to include <sys/termios.h>, because comconscflag is of type
tcflag_t.
tech-kern (?)), to get the IPL_* and IST_* types. pass the machine-dependent
cookie given at attach time on to sub-devices, so they can use it to access
the interrupt functions properly.
the isa_chipset_tag_t type, and to define or prototype:
isa_attach_hook()
isa_intr_establish()
isa_intr_disestablish()
i.e. the machine-dependent functions to be used my MI ISA code.
Remove prototypes for the latter two functions from this file.
* Add an ACB_RESET flag, so that a BUS DEVICE RESET can be queued within the
driver.
* If ACB_ABORT or ACB_RESET is set during reselection, schedule a message and
assert ATN.
* Optimize aic_datain_pio(), aic_dataout_pio() and aicintr() somewhat.
* Schedule a timeout only when we select the target, so that commands can't
time out prematurely.
1) If we get an unexpected disconnect, issue a REQUEST SENSE, as recommended
by the SCSI-2 spec. If the target created a contingent allegiance condition,
this will clear it. Also, if it happened while sending a SDTR or WDTR message,
disable negotiation for that target.
2) Since some lame devices still don't deal correctly, make sure we deassert
ATN if our last message out is interrupted. If we get a MESSAGE PARITY ERROR,
we'll reassert ATN anyway. This should ensure that we never have to send a
MESSAGE NO OPERATION.
3) Set AIC_ABORTING only when actually sending a BUS DEVICE RESET or ABORT,
so we get better error detection.
4) Other internal reorganization of no consequence.
(1) make pci functions take as an argument a machine-dependent
cookie, to allow more flexibility in implementation.
(use of other PCI functions, etc., left unchanged.)
* Display as much revision info as we can get.
* Fix a race condition that could cause interrupts to be lost.
* Handle `out of mailbox' conditions (much) more gracefully.
* Schedule timeouts more safely.
* Add diagnostic code to (correctly) detect if a CCB times out before its
outgoing mailbox is emptied.
only include the relevant code in the probe & attach functions. Still
one probe and one attach function, with #ifdefs, but this is a step
in the right direction and saves a few hundred bytes (ooh, ahh!).
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
they're base I/O ports, not really addresses. rather than using those
softc fields directly, assign local variables (asicbase, nicbase) to have
their values, and use those. (consistency, plus better optimization
potential in some cases.)
eventually. rename the probe functions for the various boards to 'find' for
consistency/correctness (but the generic8390 check is still a 'probe').
Add protos for ed_find(), ed_probe_generic8390(), ed_find_WD80x3(),
ed_find_3Com(), and ed_find_Novell(). Fix one minor space nit.
'flags 1' on the sb? kernel configuration file line (because it frobs a
noncontiguous IO port to configure the Jazz16 extensions).
Also, remove static sb_device structure and fill in user's buffer on
each request.
ends of lines, turn aligned blocks of eight spaces into tabs, name all
softc elements with the "sc_" prefix, and call the softc by the commonly
used name, "sc", when passing it around.
substantial reworking of the multi-port drivers, as they need to frob
bits in the io-port spaces of their children. As a result, the
commulti->com attachment interface is substantially more complex.
(This may be fixable in the future by making some of the code common,
but as long as io-port allocation checking is planned, it's necessary.)
macro where appropriate. No point in hard-coding numbers in multiple places.
At the very least, this makes the drivers slightly easier to diff/understand.
attaching, and to the devices when attaching them. #include <machine/bus.h>
to make this backward compatible with old #include requirements.
Also, clean up idempotency so that isa/eisa/pci "var.h" headers are
consistent (make them all idempotent).
keep going.
Improve error messages to include device name.
use STATIC for function declarations/definitions so it's easier to get a
useful symbol table by flipping a switch.
* Snap the sample rate when setting it, and remember only the time constant.
* Set the time constant when changing between play/record.
* Always return the actual sample rate with AUDIO_GETINFO.
* Add more delays while writing registers.
* Replace sc_dma{in,out}_inprogress with sc_dmadir.
* Eliminate the need for sc_locked.
* Add more DPRINTF()s.
- New metrics handling. Metrics are now kept in the new
`struct disk'. Busy time is now stored as a timeval, and
transfer count in bytes.
- Storage for disklabels is now dynamically allocated, so that
the size of the disk structure is not machine-dependent.
- Several new functions for attaching and detaching disks, and
handling metrics calculation.
Old-style instrumentation is still supported in drivers that did it before.
However, old-style instrumentation is being deprecated, and will go away
once the userland utilities are updated for the new framework.
For usage and architectural details, see the forthcoming disk(9) manual
page.
again, and it turned NetBSD in ostype[] to N^CtBSD... Thanks Charles (again)
Also call epstop() in the attach routine to make sure that the pci card
gets reset properly.
bouyer