This commit adds subsections for each device section.
Subsections is the way to handle information that don't need to be sent
to de destination of a migration because its values are not needed. It is
the way to handle optional information. Notice that only the source can
decide if the information is optional or not. The destination needs to
understand all subsections that it receives to have a sucessful load.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit ed487bb1d6.
The conflicts are due to commit 4fc8d6711a
that is a fix to the ide_drive_pre_save() function. It reverts both
(and both are reinstantiated later in the series)
Conflicts:
hw/ide/core.c
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Otherwise we can't migrate after we've removed a virtio block device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The GET EVENT STATUS NOTIFICATION is a mandatory command according
to MMC-3, even if event status notification is not supported.
This patch adds support for this command. It returns NEA ("No Event
Available") with an empty "Supported Event Classes" to show that it
doesn't event support status notification. If asychronous operation is
requested, which requires NCQ support, it returns an error according
to the specifications.
This fixes HAL support on FreeBSD and derivatives, which fill up the
logs every second with:
acd0: FAILURE - unknown CMD (0x03) ILLEGAL REQUEST asc=0x20 ascq=0x00
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some SW drivers dont keep track of what they've written and
depend on the HW latching write contents for later
read+modify+write sequences.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Commit 36388314fe moved most of the
interrupt logic to cpu-exec.c. Remove the remaining useless code
and fix software interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Edgar E. Iglesias <edgar@axis.com>
Tested-by: Edgar E. Iglesias <edgar@axis.com>
When hw interrupt pending bits in CP0_Cause are set, the CPU should
see the hw interrupt line as active. The CPU may or may not take the
interrupt based on internal state (global irq mask etc) but the glue
logic shouldn't care.
This fixes MIPS external hw interrupts in combination with -icount.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Remove pci_{register, unregister}_secondary_bus() by open code.
They are old stype API and aren't used any more by others. So eliminate it.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid confusion of primary bus with secondary bus,
rename PCIBridge::bus to PCIBridge::sec_bus.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move pci bridge related code into pci_bridge.c from pci.c
for further enhancement. pci.c is big enough now, so split it out.
No code change but exporting some accesser functions.
In fact, few pci bridge functions stays in pci.c.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The request completion callback of the LSI controller may start the next
request that can use the same tag as the completed one. As the latter is
still enqueued at that point, scsi_send_command will complain about the
tag reuse and cancel the completed request. That will cause a double
free later on when the completion path cleans up as well.
Fix this by dequeuing the request before invoking the callback.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change fixes initialization of e1000's microwire EEPROM internal
state values so that qemu's e1000 emulation works on NetBSD,
which doesn't use Intel's em driver but has its own wm driver
for the Intel i8254x Gigabit Ethernet.
Previously set_eecd() function in e1000.c clears EEPROM internal state
values on SK rising edge during CS==L, but according to FM93C06 EEPROM
(which is MicroWire compatible) data sheet, EEPROM internal status
should be cleared on CS rise edge regardless of SK input:
"... a rising edge on this (CS) signal is required to reset the internal
state-machine to accept a new cycle .."
and nothing should be changed during CS (chip select) is inactive.
Intel's em driver seems to explicitly raise SK output after CS is negated
in em_standby_eeprom() so many other OSes that use Intel's driver
don't have this problem even on the previous e1000.c implementation,
but I can't find any articles that say the MICROWIRE or EEPROM spec
requires such sequence, and actually hardware works fine without it
(i.e. real i82540EM has been working on NetBSD).
This fix also changes initialization to clear each state value in
struct eecd_state individually rather than using memset() against
the whole structre. The old_eecd member stores the last SK and CS
signal levels and it should be preserved even after reset of internal
EEPROM state to detect next signal edges for proper EEPROM emulation.
Signed-off-by: Izumi Tsutsui <tsutsui@ceres.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Starting with qemu -M pc-0.12 -device virtio-serial
results in
-device virtio-serial: Property 'virtio-serial-pci.max_nr_ports' not found
The property name 'max_ports' is incorrectly named 'max_nr_ports'. Fix
that.
Also fix the ppc440 machine type bamboo-0.12 which has this typo.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use empty_slot to reserve addresses for several unimplemented devices so they won't fault.
- BPP (parallel port), DBRI (audio), SX (pixel processor), and vsimms (framebuffer)
OBP for SS-20 either assumes these devices exist or probes without expecting faults.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
move out pci internal structures, PCIBus, PCIBridge and pci_bus_info into
private header file, pci_internals.h.
This is a preparation. Later pci bridge implementation will be
split out form pci.c into pci_bridge.c.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We need to know ring layout to allocate log buffer.
So init rings first.
Also fixes a theoretical memory-leak-on-error.
https://bugzilla.redhat.com/show_bug.cgi?id=615228
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
We do range check for size, and get size as buffer,
but copy size + 4 bytes (4 is for FCS).
Let's copy size bytes but put size + 4 in length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Disks without media make no sense. For SCSI, a Linux guest kernel
complains during boot. I didn't try other combinations.
scsi-generic doesn't need the additional check, because it already
requires bdrv_is_sg(), which fails without media.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the check from virtio_blk_init_pci(), where it protects only
virtio-blk-pci, to virtio_blk_init(). Without that, virtio-blk-s390
initializes without a drive. I figure that can lead to null pointer
dereferences.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It can't actually fail now, but the next commit will change that.
s390_virtio_blk_init() already checks for failure, but
virtio_blk_init_pci() doesn't. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In addition to the previous fix for calling do_flush_queued_data() only
when the virtqueue is ready, ensure do_flush_queued_data() gets a vq
that's suitably initialised.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a virtio-serial port is removed before the guest comes up and
initialises the virtqueues, qemu exits with the message
Guest moved used index from 0 to 61440
This happens because we try to clear any pending buffers from the
virtqueue.
Ensure the virtqueue is initialised before calling any virtqueue
operations.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While running in debug mode if 9P server is unable to open the log file
it results in a SEGV deep down in glibc:
Program received signal SIGSEGV, Segmentation fault.
0x008fca8c in fwrite () from /lib/libc.so.6
(gdb) bt
#0 0x008fca8c in fwrite () from /lib/libc.so.6
#1 0x081eb87e in pprint_pdu (pdu=0x89a52e1c)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p-debug.c:380
#2 0x0806dad8 in submit_pdu (s=0x897dc008, pdu=0x89a52e1c)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p.c:3092
#3 0x0806dc63 in handle_9p_output (vdev=0x897dc008, vq=0x86d8218)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p.c:3122
#4 0x081ac728 in virtio_queue_notify (vdev=0x897dc008, n=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio.c:563
#5 0x08063876 in virtio_ioport_write (opaque=0x86d7b98, addr=16, val=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-pci.c:222
#6 0x08063e26 in virtio_pci_config_writew (opaque=0x86d7b98, addr=16, val=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-pci.c:357
#7 0x080c881a in ioport_write (index=1, address=49296, data=0) at ioport.c:80
#8 0x080c8d4c in cpu_outw (addr=49296, val=0) at ioport.c:204
#9 0x08073010 in kvm_handle_io (port=49296, data=0xab393000, direction=1, size=2, count=1)
at /data/sripathi/code/qemu/new/qemu-next-upstream/kvm-all.c:735
...
...
This is ugly and misleading. The following patch adds a BUG_ON to catch this
error. With this patch we get an abort message like the following, which makes
it easier to analyze:
f12-kvm login: qemu: /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p-debug.c:353: pprint_pdu: Assertion `!(!llogfile)' failed.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No need to call cpu_register_physical_memory() for a zero sized area.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The file, vt82c686.c, was added after the change set of
b80d4a9887 and
fecb93c45c
are created, but before the patch series was commit.
So similar fix is needed to vt82c686.c.
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We were requesting too much when checking buffer
length: size already includes host header length.
Further, we should not exit if we get a packet that
is too long, since this might not be under control
of the guest. Just drop the packet.
Red Hat bz 591494
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
make pci hotplug callback return value to caller.
And when returning error, allocated resources are freed.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make init value for this register match the spec.
BAR address is 0 at init, so enabling it
only works by chance.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pcnet enables memory/io on init, which
does not make sense as BAR values are wrong.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Clear interrupt disable bit on reset, according to PCI spec.
Fix pci_device_reset() with 64bit BAR.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Intel Macs have a chip called the "AppleSMC" which they use to control
certain Apple specific parts of the hardware, like the keyboard background
light.
That chip is also used to store a key that Mac OS X uses to decrypt binaries.
This patch adds emulation for that chip, so we're getting one step further
to having Mac OS X run natively on Qemu.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Set PCI multi-function bit according to multifunction property.
PCI address, devfn ,is exported to users as addr property,
so users can populate pci function(PCIDevice in qemu)
at arbitrary devfn.
It means each function(PCIDevice) don't know whether pci device
(PCIDevice[8]) is multi function or not.
So this patch allows user to set multifunction bit via property
and checks whether multifunction bit is set correctly.
Cc: Juan Quintela <quintela@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
make pci bridge aware of pci multi function property and let pci generic
code to set the bit.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use pci_create_simple_multifunction() for normal device which sets
multifunction bit.
At the moment, only pc_piix.c and mips_malta.c uses multifunction
devices with piix3/4 pci-isa bridge.
And other boards don't populate those devices.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
introduce multifunction property.
Also introduce new convenient device creation function which
will be used later.
For bisectability this patch doesn't do anything, but sets the property
resulting in no functional changes.
Actual changes will be introduced by later patch.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
replace PCIDeviceInfo::header_type with is_bridge
as suggested by Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Auto-assigned-address pci function (passing devfn = -1) is always
single function.
This patch adds assert() to guarantee that auto-assigned-address function
is always single function device at function = 0.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use PCI_DEVFN() and PCI_FUNC_MAX where appropriate.
This patch make it clear that func = 0.
test:
The following object files with/without this patch are stripped and compared.
They remains same.
arm-softmmu/versatile_pci.o
libhw32/ppce500_pci.o
libhw32/unin_pci.o
libhw64/ppce500_pci.o
libhw64/unin_pci.o
mips-softmmu/gt64xxx.o
mips64-softmmu/gt64xxx.o
mips64el-softmmu/gt64xxx.o
mipsel-softmmu/gt64xxx.o
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yu Liu <yu.liu@freescale.com>
Cc: Paul Brook <paul@codesourcery.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Stuff a pointer to the DeviceState into the VirtIONet structure so that
we can easily remove the vmstate entry later. Also, let vmstate track
the instance number (it should always be zero internally since the
device path should now be unique).
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows us to create a more meaningful savevm string.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When available, we'd like to be able to access the DeviceState
when registering a savevm. For buses with a get_dev_path()
function, this will allow us to create more unique savevm
id strings.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This works great for PCI since a <segment>:<bus>:<dev>.<fn> uniquely
describes a global address. No need to traverse up the qdev tree.
PCI segment support is a placeholder for compatibility once we
support multiple segments.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This function is meant to provide a stable device path for buses
which are able to implement it. If a bus has a globally unique
addresses scheme, one address level may be sufficient to provide
a path. Other buses may need to recursively traverse up the
qdev tree.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This will benefit us when we migrate based on ramblock name since
we won't be bouncing between separate blocks.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Convert alarm time from BCD if needed before comparing with current
time.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When the controller raises the SCSI reset line, we have to perform the
requested reset on all disks attached to the controller's bus. Moreover,
reset is edge triggered, so avoid repeating it if the line was already
high.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
drive_init() doesn't permit invalid CHS for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit option readonly for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It still always succeeds. The next commits will add failures.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The two aren't independent variables. Make that obvious.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use error_report(), because it points to the error location.
Reword "tried to assign twice" messages to make it clear that we're
complaining about the unit property.
Report invalid unit property instead of failing silently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit rerror for if=scsi, but that's worthless:
we get it via if=none and -device.
Moreover, scsi-generic doesn't support werror. Since drive_init()
doesn't catch that, option werror was silently ignored even with
if=scsi.
Wart: unlike drive_init(), we don't reject the default action when
it's explicitly specified. That's because we can't distinguish "no
rerror option" from "rerror=report", or "no werror" from
"rerror=enospc". Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some of the failures are internal errors, and hw_error() is okay then.
But the common way to fail is bad user input, e.g. -global
isa-fdc.driveA=foo where drive foo has an unsupported rerror value.
exit(1) instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit them for if=floppy, but that's worthless:
we get them via if=none and -global.
This can make device initialization fail. Since all callers of
fdctrl_init_isa() ignore its value, change it to die instead of
returning failure. Without this, some callers would ignore the
failure, and others would crash.
Wart: unlike drive_init(), we don't reject the default action when
it's explicitly specified. That's because we can't distinguish "no
rerror option" from "rerror=report", or "no werror" from
"rerror=enospc". Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the final missing bits for support of
passing a serial/id string to a virtio-blk guest driver.
The guest-side component already exists in the virtio
driver, and has recently been reworked by Ryan to export
a /sys interface for retrieval of the id from guest userland.
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drives defined with -drive if=ide get get created along with the IDE
controller, inside machine->init(). That's before cmos_init().
Drives defined with -device get created during generic device init.
That's after cmos_init(). Because of that, CMOS has no information on
them (type, geometry, translation). Older versions of Windows such as
XP reportedly choke on that.
Split off the part of CMOS initialization that needs to know about
-device devices, and turn it into a reset handler, so it runs after
device creation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For instance, -device scsi-disk,drive=foo -device scsi-disk,drive=foo
happily creates two SCSI disks connected to the same block device.
It's all downhill from there.
Device usb-storage deliberately attaches twice to the same blockdev,
which fails with the fix in place. Detach before the second attach
there.
Also catch attempt to delete while a guest device model is attached.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We automatically delete blockdev host parts on unplug of the guest
device. Too much magic, but we can't change that now.
The delete happens early in the guest device teardown, before the
connection to the host part is severed. Thus, the guest part's
pointer to the host part dangles for a brief time. No actual harm
comes from this, but we'll catch such dangling pointers a few commits
down the road. Clean up the dangling pointers by delaying the
automatic deletion until the guest part's pointer is gone.
Device usb-storage deliberately makes two qdev properties refer to the
same drive, because it automatically creates a second device. Again,
too much magic we can't change now. Multiple references worked okay
before, but now free_drive() dies for the second one. Zap the extra
reference.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers of ide_create_drive() ignore its value. Currently
harmless, because it fails only when qdev_init() fails, which fails
only when ide_drive_initfn() fails, which never fails.
Brittle. Change it to die instead of silently ignoring failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
None of its callers checks for failure. scsi_hot_add() can crash
because of that:
(qemu) drive_add 4 if=scsi,format=host_device,file=/dev/sg1
scsi-generic: scsi generic interface too old
Segmentation fault (core dumped)
Fix all callers, not just scsi_hot_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scanf calls must not use PRI constants, they have probably the wrong size and
corrupt memory. We could replace them by SCN ones, but strtol is simpler than
scanf here anyway. While at it, also fix the parsers to reject garbage after
the number ("4096xyz" was accepted before).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Richard Henderson <rth@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The commit 8e65b7c049 introduced
expire_time of UHCIState. But expire_time is not in vmstate, the
second uhci_frame_timer will not be fired immediately after loadvm.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For all i, ports_map[i] is used in and only in the i-th iteration.
Replace the dynamic array by a scalar variable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
lsi_bad_phase has a bug in the choice of pmjad1/pmjad2. This does
not matter with Linux guests because it uses just one routine for
both, but it breaks Windows 64-bit guests. This is the text
from the spec:
"[The PMJCTL] bit controls which decision mechanism is used
when jumping on phase mismatch. When this bit is cleared the
LSI53C895A will use Phase Mismatch Jump Address 1 (PMJAD1) when
the WSR bit is cleared and Phase Mismatch Jump Address 2 (PMJAD2)
when the WSR bit is set. When this bit is set the LSI53C895A will
use jump address one (PMJAD1) on data out (data out, command,
message out) transfers and jump address two (PMJAD2) on data in
(data in, status, message in) transfers."
Which means:
CCNTL0.PMJCTL
0 SCNTL2.WSR = 0 PMJAD1
0 SCNTL2.WSR = 1 PMJAD2
1 out PMJAD1
1 in PMJAD2
In qemu, what you get instead is:
CCNTL0.PMJCTL
0 out PMJAD1
0 in PMJAD2 <<<<<
1 out PMJAD1
1 in PMJAD1 <<<<<
Considering that qemu always has SCNTL2.WSR cleared, the two marked cases
(corresponding to phase mismatch on input) are always jumping to the
wrong PMJAD register. The patch implements the correct semantics.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MASTER_DISABLE bit (aka mask-all) masks all the interrupts.
According to Sun-4M System Architecture
"The level–15 interrupt sources [...] are maskable with the Interrupt Target
Mask Register. While these interrupts are considered ’non–maskable’ within
the SPARC IU, a mask capability is provided to allow the boot firmware
to establish a basic environment before receiving any level–15 interrupts,
which are non–maskable within SPARC. A mask–all bit is provided to allow
disabling of all external interrupts during change of the CIT."
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
System architecture dictates whether HAS_AUDIO is defined. It's then
useless to check for HAS_AUDIO in files which are only used on those
architectures which always have audio.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The comment suggests we're checking for the driver in the ready
state and bus master disabled, but the code is checking that it's
not in the ready state.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Found-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
On Host/Fileserver:
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:36 afifo
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:32 blkdev
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:33 chardev
On Guest/Client:
prw-r--r-- 1 guestuser guestuser 0 2010-05-11 12:36 afifo
brw-r--r-- 1 guestuser guestuser 0, 0 2010-05-11 12:32 blkdev
crw-r--r-- 1 guestuser guestuser 4, 5 2010-05-11 12:33 chardev
In the passthrough securit model, specifal files are directly created
on the fileserver. But the user credential
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
Implemntation of symlink in mapped security model:
A regular file is created and the link target is written to it.
readlink() reads it back from the file.
On Guest/Client:
lrwxrwxrwx 1 root root 6 2010-05-11 12:20 asymlink -> afile
On Host/Fileserver:
-rw-------. 1 root root 6 2010-05-11 09:20 asymlink
afile
Under passthrough model, it just calls underlying symlink() readlink()
system calls are used.
Under both security models, client user credentials are changed
after the filesystem objec creation.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the mapped security model, VirtFS server intercepts and maps
the file object create and get/set attribute requests. Files on the fileserver
will be created with VirtFS servers (QEMU) user credentials and the
client-users credentials are stored in extended attributes. On the request
to get attributes, server extracts the client-users credentials
from extended attributes and sends them to the client.
On Host/Fileserver:
-rw-------. 2 virfsuid virtfsgid 0 2010-05-11 09:19 afile
On Guest/Client:
-rw-r--r-- 2 guestuser guestuser 0 2010-05-11 12:19 afile
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
mapped model changes the owner in the extended attributes.
passthrough model does the change through lchown() as the
server don't need to follow the link and client will send the
actual filesystem object.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds required infrastructure for the new security model.
- A new configure option for attr/xattr.
- if CONFIG_VIRTFS will be defined if both CONFIG_LINUX and CONFIG_ATTR defined.
- Defines routines related to both security models.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The new option is:
-fsdev fstype,id=myid,path=/share_path/,security_model=[mapped|passthrough]
-virtfs fstype,path=/share_path/,security_model=[mapped|passthrough],mnt_tag=tag
In the case of mapped security model, files are created with QEMU user
credentials and the client-user's credentials are saved in extended attributes.
Whereas in the case of passthrough security model, files on the
filesystem are directly created with client-user's credentials.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch rearranges the fileop structures by moving the structure definitions
from virtio-9p.c to virtio-9p.h file. No functional changes.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fluesh the debug messages to the log file at the end of each
debug message.
Changes from V1:
Used fflush instead fseek for the flush.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although it is really rare to get in to the while loop, the list
operation in the loop is obviously wrong.
Signed-off-by: Yoshiaki Tamura <tamura.yoshiaki@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add MAINTENANCE_IN and MAINTENANCE_OUT case in
scsi_req_length() for TYPE_ROM with MMC commands. It also adds the MAINTENANCE_OUT
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing write data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add the PERSISTENT_RESERVE_OUT cdb
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing WRITE data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make APICState completely private to apic.c by using DeviceState
in external APIs.
Move apic_init() to pc.c.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Convert to qdev.
Use an opaque CPUState pointer because of missing VMState
implementation for CPUState.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move the actual CPUState contents handling to cpu.h and cpuid.c.
Handle CPU reset and set env->halted in pc.c.
Add a function to get the local APIC state of the current
CPU for the MMIO.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Comparing an 8 bit value with ~0 does not work as expected.
Replace ~0 by UINT8_MAX in comparison and also in assignment
(and fix coding style, too).
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: malc <av1474@comtv.ru>
Correct definitions for FD_CMD_SAVE and FD_CMD_RESTORE in hw/fdc.c
Per https://bugs.launchpad.net/qemu/+bug/424453 the correct values
for FD_CMD_SAVE is 0x2e and FD_CMD_RESTORE is 0x4e. Verified against
the Intel 82078 manual which can be found at:
http://wiki.qemu.org/Documentation/HardwareManuals page 22.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PCI hotplug currently doesn't work after a migration because
we don't migrate the enable bits of the GPE state. Pull hotplug
structs into vmstate.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Setting the ID in pci_nic_init() is a blatant violation of the
DeviceState abstraction. Which even carries a comment advising
against this:
/* This structure should not be accessed directly. We declare it here
so that it can be embedded in individual device state structures. */
What's worse, it bypasses the code ensuring unique qdev IDs: "-device
virtio-net-pci,id=foo -net nic,id=foo -net nic,name=foo" happily
creates three qdevs with ID "foo". That's because qdev relies on
qemu_opts_create() to ensure unique IDs, but -net nic uses a different
QemuOptsList, which means id is in a different namespace. And its
name is not checked for uniqueness at all.
-net nic and pci_add are legacy. Use -device and device_add if you
want a NIC with a qdev ID.
This reverts what's still left of commit eb54b6dc "qdev: add id=
support for pci nics."
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When mistakenly configuring two devices in the same PCI slot,
QEMU gives a not entirely obvious message about a 'devfn' being
in use:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu-kvm: -device virtio-balloon-pci,bus=pci.0,addr=0x3: PCI: devfn 24 not available for virtio-balloon-pci, in use by rtl8139
The user does not configure 'devfn' numbers, they use slot+function.
Thus the error messages should be reported back to the user with that
same terminology rather than the internal QEMU terminology. This
patch makes it report:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu: -device virtio-balloon-pci,bus=pci.0,addr=0x3.7: PCI: slot 3 function 0 not available for virtio-balloon-pci, in use by rtl8139
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Pass the MultiReqBuffer structure down all the way to the I/O submission
instead of takin it apart. Also mark num_writes unsigned as it can't
go negative, and take the check for any pending I/O requests into the
submission function. Last but not least rename do_multiwrite to
virtio_submit_multiwrite to fit the general naming scheme and make clear
what it does.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
There is a 1:1 relation between VirtIOBlock and BlockDriverState instances,
no need to track it because it won't change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a USB keyboard is unplugged, the keyboard eventhandler is never
removed, and events will continue to be passed through to the device,
causing crashes or memory corruption.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently HPET ACPI table is created regardless of whether qemu actually
created hpet device. This may confuse some guests that don't check that
hpet is functional before using it. Solve this by passing info about
hpets in qemu to seabios via fw config interface. Additional benefit is
that seabios no longer uses hard coded hpet configuration. Proposed
interface supports up to 8 hpets. This is the number defined by hpet
spec.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The capability register is read-only from guest POV, so we do not need
to update it on reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change #define DEBUG to #define E1000_DEBUG in hw/e1000.c to make
it possible to build QEMU with -DDEBUG
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Remove unused DEBUG defines from hw/msix.c to avoid having anything
define the word DEBUG without any additions such as MSIX_DEBUG.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the HPET capability of routing IRQs to the front-side
bus, aka MSI support. This feature can be enabled via the qdev property
"msi" and is off by default.
Note that switching it on can cause guests (at least Linux) to use the
HPET as timer instead of the LAPIC. KVM users should recall that only
the latter is currently available as fast in-kernel model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
One HPET block supports up to 32 timers. Allow to instantiate more than
the recommended and implemented minimum of 3. The number is configured
via the qdev property "timers". It is also saved/restored so that it
need not match between migration peers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By implementing this feature we can also remove a nasty way to kill qemu
(by trying to enable level-triggered hpet interrupts).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of keeping a static reference around, pass the state to
hpet_enabled and hpet_get_ticks. All callers now have it at hand. Will
once allow to instantiate the HPET more than a single time.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We have to update the qemu timer when the per-timer enable bit is
toggled, just like for HPET_CFG_ENABLE changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register the HPET as a sysbus device and create it that way. As it can
route its IRQs to any ISA IRQ, we need to connect it to all 24 of them.
Once converted to qdev, we can move reset handler and vmstate
registration into its hands as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Properly initialize HPETTimer::tn and HPETTimer::state once during
hpet_init instead of (re-)writing them on every reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Setting the main counter while the HPET is enabled may not be a good
idea of the guest, but it is supported and should, thus, not spam the
host console with warnings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This moves the private HPET structures into the C module, simplifies
some helper functions and fixes most coding style issues (biggest chunk
was improper switch-case indention). No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Also prevent out-of-bounds write access to the timers but don't spam the
host console if it triggers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
42f1ced228 removed irq lowering
during reset. However, for chip reset command and DMA reset signal,
its actually the correct thing to do.
Lower IRQ on soft reset only.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
BusState::name is allocated in qbus_create_inplace().
So it should be freed by qbus_free().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes the following compilation errors in multiboot.c
when DEBUG_MULTIBOOT is defined.
Use TARGET_FMT_plx instead of %x for target_phys_addr_t.
CC i386-softmmu/multiboot.o
cc1: warnings being treated as errors
qemu/hw/multiboot.c: In function 'mb_add_mod':
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 4 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c: In function 'load_multiboot':
qemu/hw/multiboot.c:279: error: format '%#x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:307: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:308: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
make[1]: *** [multiboot.o] Error 1
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
virtio net attempts to peek into virtio queue to
determine that we have enough space for the complete
packet to fit. However, it fails to account for space
consumed by virtio net header when it does this,
under stress this results in a failure
with the message 'truncating packet'.
redhat bz 591494.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
parse_string() qemu_strdup()s the property value. It is never freed.
It needs to be freed along with the device. Otherwise, the value of
scsi-disk property "ver" gets leaked when hot-unplugging the disk, for
instance.
Call new PropertyInfo method free() from qdev_free(). Implement it
for qdev_prop_string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDEState members drive_serial_str and version are now left empty until
an actual drive is connected. Before, they got a default value that
was overwritten when a drive got connected. Doesn't matter, because
they're used only while a drive is connected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Clean up virtio-blk.c to be more consistent using BDRV_SECTOR_SIZE
instead of hard coded 512 values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
vhost net currently keeps running after vmstop,
which causes trouble as qemy does not check
for dirty pages anymore.
The fix is to simply keep vm and vhost running/stopped
status in sync.
Tested-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previous commit added QMP documentation to the qemu-monitor.hx
file, it's is a copy of this information.
While it's good to keep it near code, maintaining two copies of
the same information is too hard and has little benefit as we
don't expect client writers to consult the code to find how to
use a QMP command.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix for too small allocation to ports_map
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Booting an arm kernel has been broken a while when booting from non zero start
address. This is due to the order of events: board init loads the kernel and
sets register 15 to the start address and then qemu_system_reset reset the cpu
making register 15 zero again.
This patch fixes the usage of the register 15 start address trick in
combination with arm_load_kernel.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
add helper function which converts root bus to pci domain.
make them aware of pci domain.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
remove defines which are already defined in pci_regs.h
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So remove unused constants,
PCI_STATUS_RESERVED_MASK_LO, PCI_STATUS_RESERVED_MASK_HI,
PCI_COMMAND_RESERVED, PCI_COMMAND_RESERVED_MASK_HI.
They were used once, but they aren't used anymore.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
add const to pci_is_express(), pci_config_size().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use pci accessor function.
don't return value because it always return 0 and
the caller doesn't check the return value.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a DPRINTF macro. Use TARGET_FMT_plx for printing target_phys_addr_t
items. Add a separate flag for debugging coalescing interrupts.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
On the real hardware (SS-5, LX) the MMU is not padded, but aliased.
Software shouldn't use aliased addresses, neither should it crash
when it uses (on the real hardware it wouldn't). Using empty_slot
instead of aliasing can help with debugging such accesses.
Signed-off-by: Artyom Tarasenko <atar4qemu@googlemail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use TARGET_FMT_plx as format placeholder for target_phys_addr_t
Signed-off-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reset is now triggered after init, no need for explicit calls anymore.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The ram_size parameter can be larger than an int, so it may be truncated.
Fix by using the correct type.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix build failure introduced by 0bfcd599e3
The format statement expects unsigned long on x86_64, but receives
unsigned long long, so gcc exits with an error.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
- remove unused host state and store pci bus pointer only
- do not map host state access into unused 1fe.10000000 range
- reorder pci region registration
- assign pci i/o region to isa_mem_base
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
hw/virtio-net.h:
#define ETH_ALEN 6
ETH_ALEN was defined by commit 7967406801
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes a mismerge of 64d564094c (wrong
patch version): We need to mask the tag value properly to obtain its
device ID.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On a real hardware changing read-only bits has no effect
Use a mask common for SCSI and Ethernet registers. The crucial
bit is DMA_INTR, because setting or clearing it may produce
spurious interrupts.
This patch allows booting Solaris 2.3
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cirrus_post_load() will be executed twice when loading vm states and then the
wrong physical memory will be registered. This issue may lead to crash qemu.
Signed-off-by: TeLeMan <geleman@gmail.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
In oneshot mode, the delta needs to come from the TimerLoad register,
not the maximum limit.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reload the timer when TimerControl is written, if the timer is to be
enabled. Otherwise, if an earlier write to TimerLoad was done while
periodic mode was not set, s->delta may incorrectly still have the value
of the maximum limit instead of the value written to TimerLoad.
This problem is evident on versatileap on current linux-next, which
enables TIMER_CTRL_32BIT before writing to TimerLoad and then enabling
periodic mode and starting the timer. This causes the first periodic
tick to be scheduled to occur after 0xffffffff periods, leading to a
perceived hang while the kernel waits for the first timer tick.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add support to read manufacturer and device ID. For everything else (eg.
lock bits) 0 is returned.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Before issuing the barrier to the block driver we need to flush our oustanding
queue of write requests, as the flush is supposed to be issued after them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The VirtIOBlockRequest structure is about 40 KB in size. This patch
avoids zeroing every request by only initializing fields that are read.
The other fields are either written to or may not be used at all.
Oprofile shows about 10% of CPU samples in memset called by
virtio_blk_alloc_request(). The workload is
dd if=/dev/vda of=/dev/null iflag=direct bs=8k running concurrently 4
times. This patch makes memset disappear to the bottom of the profile.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 3d53f5c36f introduced a segfault by erroneously making fw_cfg a
'void **' and passing it around in different ways.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We don't want pci_del in QMP. Use device_del instead.
This reverts commit 6848d82716.
Conflicts:
hw/pci-hotplug.c
sysemu.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Short story: We don't want pci_add in QMP. Long story follows.
pci_add can do two things:
* Hot plug a PCI NIC. device_add is more general.
* Hot plug a PCI disk controller, and a drive connected to it.
The controller is either virtio-blk-pci (if=virtio) or lsi53c895a
(if=scsi). With the latter, the drive is optional. Use drive_add to
hotplug additional SCSI drives. Except drive_add is not available in
QMP.
device_add is more general for controllers and the guest part of
drives. I'm working on a more general alternative for the host part
of drives.
Why am I proposing to remove pci_add from QMP before its replacement is
ready? I want it out sooner rather than later, because it isn't fully
functional (errors and drive_add are missing), and we do not plan to
complete the job. In other words, it's not really usable over QMP now,
and it's not what we want for QMP anyway. Since we don't want it to be
used over QMP, we should take it out, not leave it around as a trap for
the uninitiated.
Dan Berrange confirmed that libvirt has no need for pci_add & friends
over QMP.
This reverts commit 7a344f7ac7.
Conflicts:
hw/pci-hotplug.c
sysemu.h
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This function had been disabled from the beginning:
see 9fddaa0c0c
cpu_reset() function is in target-ppc/helper.c
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds a firmware blob to the S390 target. The blob is a simple
implementation of a virtio client that tries to read the second stage
bootloader from sectors described as of offset 0x20 in the MBR.
In combination with an updated zipl this allows for booting from virtio
block devices. This firmware is built from the same sources as the second
stage bootloader. You can find a virtio capable s390-tools in this repo:
git://repo.or.cz/s390-tools.git
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When cancelling a request, bdrv_aio_cancel may decide that it waits for
completion of a request rather than for cancellation. IDE therefore can't
abandon its DMA status before calling bdrv_aio_cancel; otherwise the callback
of a completed request would use invalid data.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
remove global variables, gpe and pci0_status by moving them
into PIIX4PMState.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add argument, DeviceState*, to pci hot plug callback.
The argument will be used later to remove global variable.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
To match rtc_xxx with qdev, make rtc_xxx accept and return ISADevice
instead of RTCState.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Finally, we can safely split out the piix specific part from pc.c
into pc_piix.c.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out pci device initialization from pc_init1() into pc_pci_device_init().
and removed unnecessary braces.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out basic device, i.e. legacy devices like floppy, initialization
from pc_init1() into pc_basic_device_init().
Later it will be used.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out vga initialization which is independent of piix
from pc_init1() as pc_vga_init().
Later it will be used.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out memory allocation and rom/bios loading which doesn't depend
on piix from pc_init1() into pc_memory_init().
Later it will be used.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
split out cpu initialization which is piix independent from pc_init1()
into pc_cpus_init(). Later it will be used.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By introducing a registering function, make pc_init1() not refer to
ferr_irq directly in order to make ferr_irq piix independent.
Later pc_init1() will be split out into another file keeping ferr_irq
static.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Introduce a function, pc_allocate_cpu_irq(), to allocate cpu irq
in order to make pic_irq_request() piix independent.
Later piix code will be split out to another file keeping pic_irq_request()
static.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Remove the reference to the global variable, rtc_state, by passing
function argument to cmos_init_hd(), cmos_init().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Cc: Paolo Bonzini <bonzini@gnu.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Remove a global variable, floppy_controller.
Since it is unnecessarily global, make it local and pass it as
a function argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
make cpu_smm_update() generic to be independent on i440fx by
registering a callback.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The changeset of 2c8d934020
prevents isa_irq_handler() from NULL refering of IsaIrqState::ioapic.
However it would be better to initialize the member before reference.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split acpi.c into the common part and the piix4 specific part.
The common part will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
add acpi constants from linux header files and
replace the old constants with them.
The acpi constants will be used by other file.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out apm register emulation for acpi.c into apm.c.
The apm emulation will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Split out piix4 smbus routines from acpi.c into pm_smbus.c and
use it.
The split out smbus emulation will be used later.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
After defining the required alias ID, we can push vmstate registration
of mc146818rtc to qdev.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Establish vmstate containers for ISA and sysbus variant, define the
iobase as instance ID alias, and let qdev do the vmstate registration
work.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
At least for isa-serial, we can already let qdev do the vmstate
registration for us. It just takes wrapping vmstate for the
encapsulating ISASerialState and defining the proper instance ID
aliases.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Some legacy users (mostly PC devices) of vmstate_register manage
instance IDs on their own, and that unfortunately in a way that is
incompatible with automatically generated ones. This so far prevents
switching those users to vmstates that are registered by qdev.
To establish a migration path, this patch introduces the concept of
alias IDs. They can be passed to an extended vmstate registration
service, and qdev provides a set service to be used during device init.
find_se will consider the alias in addition to the default ID. We can
then start generating the default ID automatically and writing it on
vmsave, thus converting that format without breaking support for upward
migration.
The user is required specify the highest vmstate version for which the
alias is required. Once this version falls behind the minimum required
for a specific vmstate, an assertion triggers to motivate cleaning up
the obsolete alias.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
In linux kernel v2.6.33, sm501 frame buffer driver modified to support
2D graphics engine on sm501 chip. One example is "fill rectangle" operation.
But current qemu's sm501 emulation doesn't support it. This results in
graphics console disturbance.
This patch introduces sm501 2D graphics engine emulation and solve this problem.
Add SM501 2D hardware engine support.
- Add 2D engine register set read/write handlers.
- Support 'fill rectangle'. Other operations are left for future work.
- Update SM501 support status comment.
Signed-off-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This was the only user of .post_save as noticed by Jan Kiszka and
seems to have been added there wrongly during conversion to
VMStateDescription.
Signed-off-by: Andrzej Zaborowski <balrogg@gmail.com>
virtio-net has return with value in a void function.
No idea why does it compile with gcc,
but this isn't standard C.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
After migration, vhost was not getting features
acked because set_features callback was never invoked.
The fix is just to invoke that callback.
Reported-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: David L Stevens <dlstevens@us.ibm.com>
Code for saving irq_state got vm_state
macros wrong, passing in the wrong parameter.
As a result, we both saved a wrong value
and restored it to a wrong offset.
This leads to device and bus irq counts getting
out of sync, which in turn leads to interrupts getting lost or
never cleared, such as
https://bugzilla.redhat.com/show_bug.cgi?id=588133
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
If the init function of a device fails, as might happen with device
assignment, we never undo the work done by do_pci_register_device().
This not only causes a bit of a memory leak, but also leaves a bogus
pointer in the bus devices array that can cause a segfault or
garbage data from 'info pci'.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We must not store references to selected devices as they may be
hot-removed. Instead, look up the device based on its tag right before
using it. If the device disappeared, throw an interrupt and disconnect.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to the LSI spec, the reset value of dcmd, dstat, and ctest2
were wrong, and sdid as well as ssid require zero initialization. There
are surely more discrepancies, this is just another increment.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Declare the input message queue empty and initialize the related state
machine properly on controller reset. This fixes unrecoverable errors
when the controller was reset during ongoing requests.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Once the I/O completion callback returned, aiocb will be released by the
controller. So we have to clear the reference not only in
scsi_write_complete, but also in scsi_read_complete. Otherwise we risk
inconsistencies when a reset hits us before the related request is
released.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Ensure that pending requests of an SCSI disk are purged on system reset
and also restore max_lba. The latter is no only present in the reset
handler as that one is called after init as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The iov functions can be useful to other code as well.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
updated version of an old patch
http://xenon.stanford.edu/~eswierk/misc/qemu-linuxbios/qemu-piix-ram-size.patch
that together with
http://www.mail-archive.com/linuxbios@linuxbios.org/msg02390.html
(which is already in coreboot trunk) allows coreboot to autodetect the amount of RAM within qemu/kvm from a register in i440 northbridge.
The message on the old patch states:
Unfortunately the current version of qemu does not set these
registers, but I have patched qemu so that it emulates the i440 more
faithfully in this regard.
Signed-off-by: Bernhard M. Wiedemann <qemudevbmw@lsmod.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't do anything special for flush.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement P9_TREMOVE support.
This gets file deletion to work.
[mohan@in.ibm.com: Fix truncate to use the relative path]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement P9_TWRITE support.
This gets write to file to work
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement P9_TSTAT support. This get the mount to work on the guest.
[kiran@linux.vnet.ibm.com: malloc to qemu_malloc conversion]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Implement P9_TVERSION support.
[sripathik@in.ibm.com: Handle unknown 9P versions as per the standards]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add helpers to obtain file stat and mode details.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Helper APIs for FID and QID management.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add minimal set of FileOperations and the corresponding implementations for
local fstype. These will be required for the FID management patches later on.
[aneesh.kumar@linux.vnet.ibm.com: rpath fix ]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add helpers to do string manipulation.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add helpers to process the PDUs.
[kiran@linux.vnet.ibm.com: malloc to qemu_malloc coversion]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch doesn't implement the 9p protocol handling
code. It adds a simple device which dump the protocol data.
[jvrao@linux.vnet.ibm.com: Little-Endian to host format conversion]
[aneesh.kumar@linux.vnet.ibm.com: Multiple-mounts support]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch creates a new command line option named -fsdev to hold any file
system specific information.
The option will currently hold the following attributes:
-fsdev fstype id=id,path=path_to_share
where
fstype: Type of the file system.
id: Identifier used to refer to this fsdev
path: The path on the host that is identified by this fsdev.
[aneesh.kumar@linux.vnet.ibm.com: Abstraction using FsContext]
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the flush_queued_data() function, we expect port to be valid. Assert
only for port and not port || discard.
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The LSI controller was lacking a system reset handler. Simply invoke the
existing soft reset handler in this case. This also allows to drop its
explicit invocation during init.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Avoid keeping zombie requests across controller reset by purging the
queue and also dropping the currently active request.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We cannot install different opaque pointer for read and write
of the same i/o address.
- handle zero address in bmdma_writeb_common and install
the same opaque pointer for both read and write access.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of doing tricks to get the pci_dev, just pass it in the 1st
place. Patch is a bit longer that reverting the pci_dev field, but it
states more clearly (IMHO) what we are doing.
It also fixes the bm test, now that you told me that ->unit is not
always valid.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Individual ports can now signal to the virtio-serial core to stop
sending data if the ports cannot immediately handle new data. When a
port later unthrottles, any data queued up in the virtqueue are sent to
the port.
Disable throttling once a port is closed (and we discard all the
unconsumed buffers in the vq).
The guest kernel can reclaim the buffers when it receives the port close
event or when a port is being removed. Ensure we free up the buffers
before we send out any events to the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Before the earlier patch, we relied on incorrect virtio api usage to
signal to the guest that a particular buffer wasn't consumed by the
host.
After fixing that, we now just discard the data the guest sends us while
a host port is disconnected or doesn't have a handler registered for
consuming data.
This commit really doesn't change anything from the current behaviour,
just makes the code slightly better by spinning off data handling to
ports in another function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We cannot indicate to the guest how much data was consumed by an app for
out_bufs. So we just have to assume the apps will consume all the data
that are handed over to them.
Fix the virtio api abuse in control_out() and handle_output().
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current guests don't send more than one iov but it can change later.
Ensure we handle that case.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current control messages are small enough to not be split into multiple
buffers but we could run into such a situation in the future or a
malicious guest could cause such a situation.
So handle the entire iov request for control messages.
Also ensure the size of the control request is >= what we expect
otherwise we risk accessing memory that we don't own.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Avi Kivity <avi@redhat.com>
Reported-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
iov_to_buf() puts the buffer contents in the iov in a linearized buffer.
iov_size() gets the length of the contents in the iov.
The iov_to_buf() function is the memcpy_to_iovec() function that was
used in virtio-ballon.c.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-net code uses iov_fill() which fills an iov from a linear
buffer. The virtio-serial-bus code does something similar in an
open-coded function.
Create a new iov.c file that has iov_from_buf().
Convert virtio-net and virtio-serial-bus over to use this functionality.
virtio-net used ints to hold sizes, the new function is going to use
size_t types.
Later commits will add the opposite functionality -- going from an iov
to a linear buffer.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If adding of ports or devices in the guest fails we can send out a QMP
event so that management software can deal with it.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The check for a 0-sized write request to a guest port is not necessary;
the while loop below won't be executed in this case and all will be
fine.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The virtio-serial code doesn't mix declarations and definitions, so
separate them out on different lines.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Allow the port 'id's to be set by a user on the command line. This is
needed by management apps that will want a stable port numbering scheme
for hot-plug/unplug and migration.
Since the port numbers are shared with the guest (to identify ports in
control messages), we just send a control message to the guest
indicating addition of new ports (hot-plug) or notifying the guest of
the available ports when the guest sends us a DEVICE_READY control
message.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If the host connection to a port is closed on the destination machine
after migration, whereas the connection was open on the source, the
guest has to be informed of that.
Similar for a host connection open on the destination.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If some ports that were hot-plugged on the source are not available on
the destination, fail migration instead of trying to deref a NULL
pointer.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The number of ports on the source as well as the destination machines
should match. If they don't, it means some ports that got hotplugged on
the source aren't instantiated on the destination. Or that ports that
were hot-unplugged on the source are created on the destination.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The target could be started with max_nr_ports for a virtio-serial device
lesser than what was available on the source machine. Fail the migration
in such a case.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This clang error is harmless but worth fixing:
CC libhw32/rc4030.o
/src/qemu/hw/rc4030.c:244:66: error: if statement has empty body [-Wempty-body]
DPRINTF("read 0x%02x at " TARGET_FMT_plx "\n", val, addr);
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The bdrv_set_geometry_hint call below is not needed - it's just setting
what was just read.
Signed-off-by: Bruce Rogers <brogers@novell.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
What is known today as bdrv_open2 becomes the new bdrv_open. All remaining
callers of the old function are converted to the new one. In some places they
even know the right format, so they should have used bdrv_open2 from the
beginning.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To be able to use config files for blkdebug, we need to make these functions
available in the tools. This involves moving two functions that can only be
built in the context of the emulator.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix clang error:
CC bt-l2cap.o
/src/qemu/hw/bt-l2cap.c:1000:41: error: if statement has empty body
[-Wempty-body]
/* TODO: Signal an error? */;
This means that l2cap_sframe_in() may now get called.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Andrew Zaborowski <balrogg@gmail.com>
When looking down child bus, it should look parent bridge's
bus number, not child bus's.
Optimized tail recursion and style fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When qemu is invoked with an invalid initrd file, it crashes. Following
patch prints a error message and exits if an invalid initrd is
specified. Includes changes suggested by JV.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
virtio_blk_req_complete frees the request, so we can't access it any more when
calling bdrv_mon_event. Use the pointer that was copied earlier.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Both functions report errors nicely enough now, no need for additional
messages.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Note: our device unplug methods don't need conversion work, because
they can't currently fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
These clang errors are harmless but worth fixing:
CC ppc-softmmu/usb-ohci.o
/src/qemu/hw/usb-ohci.c:1104:59: error: if statement has empty body [-Wempty-body]
ohci->ctrl_head, ohci->ctrl_cur);
/src/qemu/hw/usb-ohci.c:1371:57: error: if statement has empty body [-Wempty-body]
DPRINTF("usb-ohci: port %d: SUSPEND\n", portnum);
CC sparc64-softmmu/translate.o
/src/qemu/target-sparc/translate.c:3173:37: error: if statement has empty body [-Wempty-body]
; // XXX
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use empty_slot device for the RAM which is not installed
Models without ECC don't trap when missing ram is accessed.
v0->v1 compile only once and fix indentation
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The empty_slot device emulates known to a bus but not connected devices.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These clang errors are harmless but worth fixing:
CC libhw64/fdc.o
/src/qemu/hw/fdc.c:998:74: error: if statement has empty body [-Wempty-body]
FLOPPY_DPRINTF("Floppy digital input register: 0x%02x\n", retval);
CC libhw64/cuda.o
/src/qemu/hw/cuda.c:320:66: error: if statement has empty body [-Wempty-body]
CUDA_DPRINTF("read: reg=0x%x val=%02x\n", (int)addr, val);
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
So the userspace headers define KERNEL_STRICT_NAMES and there's no
conflict on type definition for older kernels.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
vhost in current kernels doesn't support mergeable buffers.
Disable this feature if vhost is enabled, until such
support is implemented.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
vhost driver in qemu didn't ack features, and this happens
to work because we don't really require any features. However,
it's better not to rely on this. This patch passes features to
vhost as guest acks them.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since commit 8da3ff1809 ("MMIO callback
interface changes"), the addresses passed to the I/O functions are an
offset to the start of the area. As a consequence, there is no need to
correct the address using the value of IOBR. This make possible the use
of the default MMIO functions. Moreover the addresses are now remaped
when the value if IOBR change.
The memory area corresponds to the devices behing the PCI bus, it should
not be mapped by the PCI controller. Remove the corresponding code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
IDE and flash are part of the R2D board, and can't be removed. Emulate
them even if there is no hard-drive plugged to the IDE or if the flash
content is empty.
So the userspace headers define KERNEL_STRICT_NAMES and there's no
conflict on type definition for older kernels.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost in current kernels doesn't support mergeable buffers.
Disable this feature if vhost is enabled, until such
support is implemented.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost driver in qemu didn't ack features, and this happens
to work because we don't really require any features. However,
it's better not to rely on this. This patch passes features to
vhost as guest acks them.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Using new pci_add_capability_at_offset makes
eepro100 code cleaner.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Weil <weil@mail.berlios.de>
Unlike virtio, device emulations need to add pci capabilities
at known offsets to match real hardware. Make this possible
by adding an appropriate API.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The guest may issue a RESET command for virtio. So far we didn't bother
to implement it, but with my new bootloader we actually need it for Linux
to get back to a safe state.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With more files from outside the hw/ directory being placed into
libhw, avoid the need to include hw/hw.h for the sake of targ_phys_addr_t.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There was a pointer cast warning on Ubuntu since _FORTIFY_SOURCE has been reenabled.
_FORTIFY_SOURCE had been disabled by 4a24470497
and reenabled by 849583050d.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Some drivers seems to access the reserved register in bank 0 so allow and
ignore these accesses.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
this fixes the smc91c111 emulation which has been broken for gumstix and
mainstone and maybe others since the "MMIO callback interface changes"
8da3ff1809 was commited.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a destroy hook for the baum character device, to properly close the BrlAPI
connection.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The bochs vbe interface got a new register a while back, which specifies
the linear framebuffer size in 64k units. This patch adds support for
the new register to qemu. With this patch applied vgabios 0.6c works
with qemu.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 15e89f5916
removed this setting, but it is still needed.
Without this patch, e100 device drivers using
interrupts don't work with qemu.
See other nic emulations which also set the
PCI interrupt pin.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_add_capability automatically updates PCI status and
PCI capability pointer, so use it. Use pci_reserve_capability
to make the new capability appear at the correct offset.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For some devices, this bit is always set.
For the others, it is set by default.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This ethernet device is used in Toshiba Tecra 8200 notebooks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By using a private device info structure
(as suggested by Gerd Hoffmann), handling of the
different device variants becomes much easier.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SCBStatus is readonly, but most drivers which were derived
from the old Linux eepro100.c do a word write to this address
when they want to acknowledge interrupts.
So we have to mask these writes here.
The patch also removes old unused code for status read / write.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move ARMv7-M PC/SP initialization to the CPU reset routine. Add a board
reset routine to call this. Also load values directly from ROM as
images have not been copied yet.
Avoid clearing the NVIC pointer on cpu reset.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Timer with zero period (free-run) will never match.
Timer counting starts with tick value of 0x200, not from 0,
so the period must calculated from one tick less than the limit.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
After commit 702f3e0fb5, the params is
nerver NULL. It should check *params instead of params to determine
whether the params is empty.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
u_int64_t raises compiler error messages:
CC libhw32/virtio.o
/qemu/ar7/hw/virtio.c: In function ‘virtio_queue_get_avail_size’:
/qemu/ar7/hw/virtio.c:776: error: ‘u_int64_t’ undeclared (first use in this function)
/qemu/ar7/hw/virtio.c:776: error: (Each undeclared identifier is reported only once
/qemu/ar7/hw/virtio.c:776: error: for each function it appears in.)
Replacing u_int64_t by uint64_t helps.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This connects virtio-net to vhost net backend.
The code is structured in a way analogous to what we have with vnet
header capability in tap.
We start/stop backend on driver start/stop as
well as on save and vm start (for migration).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds vhost net device support in qemu. Will be tied to tap device
and virtio by following patches. Raw backend is currently missing,
will be worked on/submitted separately.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Support host/guest notifiers in virtio-pci.
The last one only with kvm, that's okay
because vhost relies on kvm anyway.
Note on kvm usage: kvm ioeventfd API
is implemented on non-kvm systems as well,
this is the reason we don't need if (kvm_enabled())
around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
make it possible to use type without header include,
simplifying header dependencies.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
vhost net backend needs to be notified when
frontend status changes. Add a callback,
similar to set_features.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
vhost needs physical addresses for ring and other queue fields,
so add APIs for these. In particular, add binding API to set
host/guest notifiers. Will be used by vhost.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
event notifiers are slightly generalized eventfd descriptors. Current
implementation depends on eventfd because vhost is the only user, and
vhost depends on eventfd anyway, but a stub is provided for non-eventfd
case.
We'll be able to further generalize this when another user comes along
and we see how to best do this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Make vl.o compiled per target and fix a thinko in hw/acpi.c. It's not trivial
to make kvm.h consumable by compiled-once files.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Older Linux guests don't activate the bus master enable bit. So for those we
can just try to be clever and track if they set the DEVICE_OK bit even though
bus mastering is still disabled.
Under that condition we can disable the windows safety check. With that logic
in place both guests should work just fine. Without PCI hotplug breaks
virtio-net in Linux < 2.6.34 guests.
Signed-off-by: Alexander Graf <agraf@suse.de>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mass Storage Reset and Get Max LUN are class specific requests, but
they were not marked as such in hw/usb-msd.c, moved therefore
ClassInterfaceRequest and ClassInterfaceOutRequest from hw/usb-net.c
to hw/usb.h.
Furthermore there was a problem in hw/usb-ohci.c when using DEBUG
concerning systems where size_t is a 32 bit integer (printf resulted
in a segmentation fault).
Signed-off-by: Max Reitz <max@tyndur.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Beginning with its introduction, the virtio balloon has had an overflow error
that causes 'info balloon' to misreport the actual memory size when the balloon
itself becomes larger than 4G. Use a cast when converting dev->actual from
pages to kB to prevent overflows.
Before:
(qemu) info balloon
balloon: actual=5120
(qemu) balloon 1025
(qemu) info balloon
balloon: actual=1025
(qemu) balloon 1024
(qemu) info balloon
balloon: actual=5120
After:
(qemu) info balloon
balloon: actual=5120
(qemu) balloon 1025
(qemu) info balloon
balloon: actual=1025
(qemu) balloon 1024
(qemu) info balloon
balloon: actual=1024
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Make win2k install hack unconditional as it is still restricted to
x86 only in vl.c.
Replace TARGET_PAGE_SIZE and 4096 with PAGE_SIZE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This fixes a copy/paste bug introduced in commit
2d48377a85 that pushed TARGET_WORDS_BIGENDIAN
dependency to board level.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Convert pci_host_conf_register_mmio_noswap(x) to
pci_host_conf_register_mmio(x, 0).
Convert pci_host_conf_register_mmio(x) to
pci_host_conf_register_mmio(x, 1) for big endian hosts, all cases
happen to be BE.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
x86 definitions (especially CPUState uses) prevent many files from
being compiled within libhw.
Move x86 specific declarations (APIC stuff) to a separate file.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit d7234f4d7e.
Conflicts:
hw/xen_machine_pv.c
This should have never been committed.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All of these users have global state so we really don't see a benefit from
exit_notifier. However, using exit_notifier means that there's one less
justification for having global state in the first place.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
And convert usb-hid to use it (to avoid regression with bisection)
Right now, when we do info mice and we've added a usb tablet, we don't see it
until the guest starts using the tablet. We implement this behavior in order
to provide a means to delay registration of a mouse handler since we treat
the last registered handler as the current handler.
This is a usability problem though as we would like to give the user feedback
that they've either 1) not added an absolute device 2) there is an absolute
device but the guest isn't using it 3) we have an absolute device and it's
active.
By using QTAILQ and having an explicit activation function that moves the
handler to the front of the queue, we can implement the same semantics as
before with respect to automatically switching to usb tablet while providing
the user with a whole lot more information.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When building with -DNDEBUG, assert(0) will not stop execution
so it must not be used for abnormal termination.
Use cpu_abort() when in CPU context, abort() otherwise.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The usb-msd device emulation needs some small tweaks in the requests
emulations. For instance, the reset/maxlun requests are class/interface
specific so requests for them with the type class and recipient interface
bits sets have to be handled.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In case s->version is shorter than 4 bytes we overflow the memcpy src
buffer. Fix it by clearing the target buffer, then copy only the
amount of bytes we actually have.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't rely on CDROM hint for read_only attribute
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just tell main_loop_wait whether to be blocking or nonblocking, so that
there is no need to call qemu_cpus_have_work from the timer subsystem.
Instead, tcg_cpu_exec can say "we want the main loop not to block because
we have stuff to do".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When working with the VM state (for loadvm/savevm and migration), it is not
valid to load and store pointers since the validity of those pointers cannot be
assured in the new qemu address space. Therefore, virtio_balloon_save() and
virtio_balloon_load() must not handle the stats-related fields in struct
VirtIOBalloon.
If a memory stats request is in-flight at the time of a migration or savevm,
the request will not complete and should be resubmitted once migration or
loadvm completes. Note that this extremely small race window can only be
triggered using QMP so it is not possible to hang the user monitor.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a logical block size attribute as various guest side tools only
increase the filesystem sector size based on it, not the advisory
physical block size.
For scsi we already have support for a different logical block size
in place for CDROMs that we can built upon. Only my recent block
device characteristics VPD page needs some fixups. Note that we
leave the logial block size for CDROMs hardcoded as the 2k value
is expected for it in general.
For virtio-blk we already have a feature flag claiming to support
a variable logical block size that was added for the s390 kuli
hypervisor. Interestingly it does not actually change the units
in which the protocol works, which is still fixed at 512 bytes,
but only communicates a different minimum I/O granularity. So
all we need to do in virtio is to add a trap for unaligned I/O
and round down the device size to the next multiple of the logical
block size.
IDE does not support any other logical block size than 512 bytes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Many usbdevice_init implementors assume params is non-NULL.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
QEMU uses a fixed page size for the CPU TLB. If the guest uses large
pages then we effectively split these into multiple smaller pages, and
populate the corresponding TLB entries on demand.
When the guest invalidates the TLB by virtual address we must invalidate
all entries covered by the large page. However the address used to
invalidate the entry may not be present in the QEMU TLB, so we do not
know which regions to clear.
Implementing a full vaiable size TLB is hard and slow, so just keep a
simple address/mask pair to record which addresses may have been mapped by
large pages. If the guest invalidates this region then flush the
whole TLB.
Signed-off-by: Paul Brook <paul@codesourcery.com>
We sometimes permit omitting the first option name, for example
-device foo is short for -device driver=foo. The name to use
("driver" in the example) is passed as argument to qemu_opts_parse().
For each QemuOptsList, we use at most one such name.
Move the name into QemuOptsList, and pass whether to permit the
abbreviation. This ensures continued consistency, and simplifies the
commit after next in this series.
This reverts commit 3ced9f7a36.
The next commit will convert all of qdev_device_add() to QError, and
it'll be clearer with this partial conversion reverted.
Users can't set them, so qdev_device_help() shouldn't list them. Fix
that. Also make qdev_prop_parse() hide them instead of printing a
meaningless "has no parser" error message.
Their value means nothing to users, so qdev_print_props() shouldn't
print it. Fix by removing their print method.
Their only use is dirty hacks. Document that.
Users can't create them, so qdev_device_help() shouldn't list them.
Fix that.
Also make qdev_device_add() pretend they don't exist. Before, it
rejected them with a "can't be added via command line" message, which
wasn't quite right for monitor command device_add.
error_report() terminates the message with a newline. Strip it it
from its arguments.
This fixes a few error messages lacking a newline:
net_handle_fd_param()'s "No file descriptor named %s found", and
tap_open()'s "vnet_hdr=1 requested, but no kernel support for
IFF_VNET_HDR available" (all three versions).
There's one place that passes arguments without newlines
intentionally: load_vmstate(). Fix it up.
Commit 30d335d6 converted an informational message from
monitor_printf() to qemu_error(), probably because the latter doesn't
need a mon argument. A later commit will make qemu_error() print
additional stuff that is only appropriate for proper errors, and then
this will break. Clean it up.
qbus_find() adds an informational line to error messages, and prints
both lines with one qemu_error(). Use error_printf() for the
informational line instead.
While there, simplify: instead of printing buffers filled by
qbus_list_bus() and qbus_list_dev() in one go, make them print it.
qdev_device_help() prints device information with qemu_error(). A
later commit will make qemu_error() print additional stuff that is
only appropriate for proper errors, and then this will break. Use
error_printf() instead.
While there, simplify: instead of printing a buffer filled by
qdev_print_devinfo() in one go, make qdev_print_devinfo() print it.
The old test assumes that "hotplugged" implies "we have a current
monitor for reading the key". This is in fact true, but it's not
obviously true.
Aside: if it were false, we could pass a null pointer to
monitor_read_bdrv_key_start(), which would then crash.
The previous commit permits us to check for "we have a current
monitor" directly, so do that.
Code duplicated in commit 0ecdffbb. The two versions are similar, but
not identical:
* cmos_init() reports errors to stderr, pc_boot_set() via
qemu_error(). The latter is fine for both, so pick that for the
common code.
* cmos_init() obeys fd_bootchk, pc_boot_set() ignores it. Make it a
parameter of the common code.
Commit 0ecdffbb created pc_boot_set() for use from monitor command
"boot_set", via qemu_boot_set(). pc_boot_set() reports errors to
cur_mon, which works fine for monitor code.
Commit e0f084bf reused the function int reset handler
restore_boot_devices(). Use of cur_mon is problematic in that
context. For instance, the "Too many boot devices for PC" error for
"-boot order=abcdefgh,once=c" goes to the monitor instead of stderr.
The monitor may not even exist.
Fix by switching to qemu_error().
A few machines need to translate the ELF header addresses into physical
addresses. Currently the only possibility is to add a value to the
addresses.
This patch replaces the addend argument by and a translation function
and an opaque passed to the function. A NULL function does not translate
the address.
The patch also convert all machines that have an addend, simplify the
PowerPC kernel loading and fix the MIPS kernel loading using this new
feature. Other machines may benefit from this feature.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Real pcnet device (AT2450) apparently has subsystem
device and vendor id set to 0, this is out of spec
(which requires that vendor id is obtained from PCI SIG)
but windows xp driver seems to need this in order
to associate.
qemu sets pci subsystem id to qumranet/qemu
since d350d97d19,
debian does not yet have this patch.
https://bugzilla.redhat.com/show_bug.cgi?id=521247
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
eepro100 uses macros which rely on a specific
local variable name (pci_conf) which is scary.
Some of the uses are wrong or unnecessary,
remove them. The rest are small in number, open-code
them using pci_set_xx functions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
here's a trivial patch to fix the spelling of "compatibility":
Signed-off-by: Vagrant Cascadian <vagrant@freegeek.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix the floppy controller init wrappers to set the drive properties
only in case the DriveInfo pointers passed in are non NULL. This allows
to set the properties using -global.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's emitted whenever the watchdog device's timer expires. The action
taken is provided in the 'data' member.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add led status notification support to the usb kbd driver.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add led status notification support to the ps/2 kbd driver.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
You're supposed to use scsi-generic for that. Which rejects anything
but /dev/sg*.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Guest device and host netdev are peers, i.e. it's a 1:1 relation.
However, we fail to enforce that:
$ qemu -nodefaults --nographic -netdev user,id=net0 -device e1000,netdev=net0 -device virtio-net-pci,netdev=net0 -monitor stdio
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) info network
Devices not on any VLAN:
net0: net=10.0.2.0, restricted=n peer=virtio-net-pci.0
e1000.0: model=e1000,macaddr=52:54:00:12:34:56 peer=net0
virtio-net-pci.0: model=virtio-net-pci,macaddr=52:54:00:12:34:57 peer=net0
It's all downhill from there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Property "vlan" reports "failed to parse" even when the value parses
just fine, but the result doesn't name an existing VLAN.
Similarly, properties "drive", "chr" and "netdev" misleadingly report
"failed to parse" when the value doesn't name an existing host device.
Change PropertyInfo method parse to return an error code, so that
qdev_prop_parse() can report the error more accurately.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Use the named constant instead of -1.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
net.c used a constant to signify no MSI vectors were specified. Extend
that to all qdev devices.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reported-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to AMD document 21485D pp.141, APROMWE is bit 8 of BCR2.
Signed-off-by: Christopher Kilgour <techie@whiterocker.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The next commit will move the STOP event into do_vm_stop(), to
have the expected event sequence we need to emit the I/O error
event before calling vm_stop().
The expected sequence is:
{ "event": "BLOCK_IO_ERROR" [...] }
{ "event": "STOP" }
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Disable the MULTIPORT feature and MSI vectors for the 0.12 machine
types; those features are added only for 0.13 onwards.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a 0.12 machine type for compatibility with older versions. Mark the
default one as 0.13.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 428c149b0b modified the argument
that virtio_blk_init takes. Update the s390 bus code that calls this
function.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
UART_IIR_THRI is not a mask, but a possible value for the IIR ID.
Use UART_IIR_ID to extract this value.
Broken by commit 71e605f803.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As we hard-wire the BSP to CPU 0 anyway and cpuid_apic_id equals
cpu_index, bsp_to_cpu can also be based on the latter directly. This
will help an early user of it: KVM while initializing mp_state.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This grand cleanup drops all reset and vmsave/load related
synchronization points in favor of four(!) generic hooks:
- cpu_synchronize_all_states in qemu_savevm_state_complete
(initial sync from kernel before vmsave)
- cpu_synchronize_all_post_init in qemu_loadvm_state
(writeback after vmload)
- cpu_synchronize_all_post_init in main after machine init
- cpu_synchronize_all_post_reset in qemu_system_reset
(writeback after system reset)
These writeback points + the existing one of VCPU exec after
cpu_synchronize_state map on three levels of writeback:
- KVM_PUT_RUNTIME_STATE (during runtime, other VCPUs continue to run)
- KVM_PUT_RESET_STATE (on synchronous system reset, all VCPUs stopped)
- KVM_PUT_FULL_STATE (on init or vmload, all VCPUs stopped as well)
This level is passed to the arch-specific VCPU state writing function
that will decide which concrete substates need to be written. That way,
no writer of load, save or reset functions that interact with in-kernel
KVM states will ever have to worry about synchronization again. That
also means that a lot of reasons for races, segfaults and deadlocks are
eliminated.
cpu_synchronize_state remains untouched, just as Anthony suggested. We
continue to need it before reading or writing of VCPU states that are
also tracked by in-kernel KVM subsystems.
Consequently, this patch removes many cpu_synchronize_state calls that
are now redundant, just like remaining explicit register syncs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of allocating a separate chunk for the first 640KB and another
for 1MB+, allocate one large chunk. This plays well in terms of alignment
and size with large pages.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
I always try to keep standard includes sorted
and add a comment why they are there (so they
can be removed when they are no longer needed).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
C++ comments are unwanted, so this is fixed here.
* Replace C++ comments by C comments.
* Put code which was deactivated by a C++ comment in #if 0...#endif.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Real hardware would run an internal self-test.
The emulation just returns a passed status.
Original patch was from Reimar Döffinger, thanks.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move code which reads the command block to the
new function read_cb. The patch also fixes some
endianess issues related to the command block
and moves declarations of local variables to
the beginning of the block.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no need for a local variable "status".
Using tx.status makes it clearer which status
is addressed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CU Start is allowed when the CU is in the idle or suspended state.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The RNR interrupt is triggered under these conditions:
* the RU is not ready to receive a frame due to missing resources
* the RU is ready and a RU abort command was requested
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When compiling with -Wshadow, gcc gives a warning
which is fixed by renaming stat -> status.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of magic numbers like 0x8000, symbolic names are used
for the SCB command and status bits.
There are too many configuration bits to use symbolic names
there, too. Using the BIT macro is a little help when comparing
code and documentation.
For the same reason, some other constants were replaced by
the BITS macro.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add descriptions for all devices.
These descriptions are shown when users call
qemu -device ?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only two boot ROM files are needed for all devices.
* Add these GPXE ROM files using new naming convention
(as discussed on qemu-devel). Both files were created
with http://rom-o-matic.net/, PCI vendor / device ids
as in ROM filenames and option BANNER_TIMEOUT = 0.
* Remove old PXE ROM file for i82559er.
It was replaced by gpxe-eepro100-80861209.rom.
* Update pc-bios/README (and sort entries).
Full support still needs additional eepro100 fixes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The phy handling was wrong for PXE, GPXE boot:
GPXE's eepro100 driver did not detect a valid link.
This is fixed here.
V2 - Use UPPER_CASE for enum values
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some system control block registers were addressed
using their offset value. Use symbolic names now
and clean the documentation.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When debug output was enabled (by defining DEBUG_EEPRO100),
some debug messages resulted in a compiler error.
This is fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move userland PALcode handling into linux-user main loop so that
we can send signals from there. This also makes alpha_palcode.c
system-level only, so don't build it for userland. Add defines
for GENTRAP PALcall mapping to signals.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since kernel uimage is getting bigger,
old fixed loading bases will result in regions overlap.
Add pad for fdt and ramdisk, so that they won't overlap with uimage.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's convinent to use rom to checking overlap, to reset etc.
And uImage and ramdisk loading has already moved to it.
Also, after we add fdt to rom, free it.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
So that the following registers init could be flushed back to kvm.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Acked-by: Hollis Blanchard <hollis@penguinppc.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If -usbdevice is used on a machine with no USB busses, usb_create
will fail and return NULL. Patch below handles this failure gracefully
rather than crashing when we try to init the device.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Add a QEMU timer only when needed (timeout status not set, timeout
irq wanted and timer set).
This patch is required for Darwin. Patch has been tested under
FreeBSD, Darwin and Linux.
Signed-off-by: Frediano Ziglio <freddy77@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
o Implement receive overrun status. The FreeBSD uart driver
relies on this status in it's probe routine to determine the size
of the FIFO supported.
o As per the 16550 spec, do not overwrite the RX FIFO on an RX overrun.
o Do not allow TX or RX FIFO overruns to increment the data valid count
beyond the size of the FIFO.
o For reads of the IIR register, only clear the "TX holding register
emtpy interrupt" if the read reports this interrupt. This is required
by the specification and avoids losing TX interrupts when other,
higher priority interrupts (usually RX) are reported first.
Signed-off-by: Justin T. Gibbs <gibbs@FreeBSD.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
pci_data_write ignores high 8 bit in address,
so there seems to be no need to set them
in apb_pci.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cc1: warnings being treated as errors
/src/qemu/hw/pl181.c: In function 'pl181_fifo_run':
/src/qemu/hw/pl181.c:185: error: 'value' may be used uninitialized in this function
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The PL181 data transfer loop incorrectly terminates after the last FIFO
word is popped, discarding the last 3 bytes of data on a write transfer.
Signed-off-by: Paul Brook <paul@codesourcery.com>
/src/qemu/hw/ide/core.c: In function 'ide_drive_pre_save':
/src/qemu/hw/ide/core.c:2740: warning: comparison is always false due to limited range of data type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If the device can't be created, don't leak the QemuOpts and release the id of
the device that should have been added by the failed device_add.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Hi,
Kevin and I have agreed on the approach for this one now. So here is
the latest version of the patch for QEMU, submitting e820 reservation
entries via fw_cfg.
Cheers,
Jes
Use qemu-cfg to provide the BIOS with an optional table of e820 entries.
Notify the BIOS of the location of the TSS+EPT range to by reserving
it via the e820 table.
This matches a corresponding patch for Seabios, however older versions
of Seabios will default to the hardcoded address range and stay
compatible with current QEMU.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Michael noted we don't allow disabling of MSI for the virtio-serial-pci
device. Fix that.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 98b19252cf, all
serial devices declare MULTIPORT feature.
To allow 0.12 compatibility, we should clear this when
max_nr_ports is 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
virtio-serial-pci can support multiple ports in the current development
version that will become 0.13. Add compatibility options for the 0.12
and 0.11 pc machine types.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The version 0.13 will be the new default and compatibility options will
be added to the 0.12 version.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I found that the QEMU USB keyboard support does not work properly with
the Set_Idle command. Once a non-zero value is given to Set_Idle,
then the keyboard reports an event on every poll - not based on the
time issued in the Set_Idle command.
I changed the code (see patch below) and it works for me. I'm not
that familiar with the qemu internals, so I'm not sure if this is the
best way to implement this feature.
-Kevin
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Don't raise irq when not enabled.
Raise irq on enabling if DMA_INTR is set
Don't clear irq unless it was raised by DMA, as there are other irq sources
Don't set DMA_INTR bit spuriously.
v1->v2:
- Don't clear irq unless it was raised by DMA
- Raise irq on enabling if DMA_INTR is set
- Assume revertion of 787cfbc432
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Cleanup versatile_pci: no need to re-set fields
to zero (pci core sets 0 already), use set_word
for status field. Compile-tested only, but seems obvious.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
This converts versatile_pci to use symbolic
constants. Verified by comparing binary to
original one.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Linux with CONFIG_PPC64 doesn't support ADB devices anymore, so we have to
use USB for keyboard and mouse.
This patch enables USB per default on U3 and adds a virtual keyboard and mouse
there.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While trying to find the right channel number for the DBDMA emulation I
stumbled across segmentation faults that were purely triggered by the guest.
The guest should never have the possiblity to segfault us, so let's check
all indirect function calls on a channel, so the code even works for channels
that have not been reserved.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per default Linux doesn't come with a lot of storage adapters enabled on
Mac configurations. The one that's pretty much always present is the pmac-ide,
while the cmd64x is almost never included in any distribution.
So let's switch to use the MacIO based IDE controller. There is corresponding
OpenBIOS code to get interrupts working properly.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Our guest systems need to know by how much the timebase increases every second,
so there usually is a "timebase-frequency" property in the cpu leaf of the
device tree.
This property is missing in OpenBIOS.
With qemu, Linux's fallback timebase speed and qemu's internal timebase speed
match up. With KVM, that is no longer true. The guest is running at the same
timebase speed as the host.
This leads to massive timing problems. On my test machine, a "sleep 2" takes
about 14 seconds with KVM enabled.
This patch exports the timebase frequency to OpenBIOS, so it can then put them
into the device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The interrupt code as is didn't really work for me. I couldn't even convince
Linux to take interrupt 9 in an interrupt-map.
So let's do this right. Let's map all PCI interrupts to 0x1b - 0x1e. That way
we're at least a small step closer to what real hardware does.
I also took the interrupt pin to line conversion from OpenBIOS, which at least
assures us we're compatible with our firmware :-).
A dump of the PCI interrupt-map from a U2 (iBook):
00009000 00000000 00000000 00000000 ff97c528 00000034 00000001
0000d800 00000000 00000000 00000000 ff97c528 0000003f 00000001
0000c000 00000000 00000000 00000000 ff97c528 0000001b 00000001
0000c800 00000000 00000000 00000000 ff97c528 0000001c 00000001
0000d000 00000000 00000000 00000000 ff97c528 0000001d 00000001
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To ease debugging and to know what we're lacking, I found it really useful to
have an lspci dump of a real U3 based G5 around. So I added a comment for it.
If people don't think it's important enough to include this information in the
sources, just don't apply this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "Mac99" type so far defines a "U2" based configuration. Unfortunately,
there have never been any U2 based PPC64 machines. That's what the U3 was
developed for.
So let's split the Mac99 machine in a PPC64 and a PPC32 machine. The PPC32
machine stays "Mac99", while the PPC64 one becomes "Mac99_U3". All peripherals
stay the same.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Uninorth PCI bridge requires different layouts in its PCI config space
accessors.
This patch introduces a conversion function that makes it compatible with
the way Linux accesses it.
I also kept an OpenBIOS compatibility hack in. I think it'd be better to
take small steps here and do the config space access rework in OpenBIOS
later on. When that's done we can remove that hack.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove useless set to zero lines. Latency programming should be
done by BIOS, reset value is zero.
Add revision to APB, don't enable PCI_COMMAND_MASTER and set status
according to APB specification.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit c2039bd0ff made rom loading
automatic for non-PC architectures. Remove now mostly unused
conditional rom loading support.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes 525e05147d.
pci host bridge doesn't have header type of bridge.
The check should be by header type, instead of pci class device.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export the physical block size in the READ CAPACITY (16) command,
and add the new block limits VPD page to export the minimum and
optiomal I/O sizes.
Note that we also need to bump the scsi revision level to SPC-2
as that is the minimum requirement by at least the Linux kernel
to try READ CAPACITY (16) first and look at the block limits VPD
page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Export all topology information in the block config structure,
guarded by a new VIRTIO_BLK_F_TOPOLOGY feature flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The addition of the whole ATA IDENTIY page caused the config space to
go above the allowed size in the PCI spec, and thus the feature was
already reverted in the Linux guest driver and disabled by default in
qemu.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It's not needed to check the return of qobject_from_jsonf()
anymore, as an assert() has been added there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix a race condition where qemu finds that there are not enough virtio
ring buffers available and the guest make more buffers available before
qemu can enable notifications.
Signed-off-by: Tom Lendacky <toml@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes a segfault due to buffer overrun in the usb-serial device.
The memcpy was incrementing the start location by recv_used yet, the
computation of first_size (how much to write at the end of the buffer
before wrapping to the front) was not accounting for it. This causes the
next element after the receive buffer (recv_ptr) to get overwritten with
random data.
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I have streaming audio devices working within qemu-kvm. This is a port
of the changes to qemu.
Streaming audio generates a series of isochronous requests that are
repetitive and time sensitive. The URBs need to be submitted in
consecutive USB frames and responses need to be handled in a timely manner.
Summary of the changes for isochronous requests:
1. The initial 'valid' value is increased to 32. It needs to be higher
than its current value of 10 since the host adds a 10 frame delay to the
scheduling of the first request; if valid is set to 10 the first
isochronous request times out and qemu cancels it. 32 was chosen as a
nice round number, and it is used in the path where a TD-async pairing
already exists.
2. The token field in the TD is *not* unique for isochronous requests,
so it is not a good choice for finding a matching async request. The
buffer (where to write the guest data) is unique, so use that value instead.
3. TD's for isochronous request need to be completed in the async
completion handler so that data is pushed to the guest as soon as it is
available. The uhci code currently attempts to process complete
isochronous TDs the next time the UHCI frame with the request is
processed. The results in lost data since the async requests will have
long since timed out based on the valid parameter. Increasing the valid
value is not acceptable as it introduces a 1+ second delay in the data
getting pushed to the guest.
4. The frame timer needs to be run on 1 msec intervals. Currently, the
expire time for the processing the next frame is computed after the
processing of each frame. This regularly causes the scheduling of frames
to shift in time. When this happens the periodic scheduling of the
requests is broken and the subsequent request is seen as a new request
by the host resulting in a 10 msec delay (first isochronous request is
scheduled for 10 frames from when the URB is submitted).
[ For what's worth a small change is needed to the guest driver to have
more outstanding URBs (at least 4 URBs with 5 packets per URB).]
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The write the the PA_POWOFF register is currently ignored. Fix that by
calling qemu_system_shutdown_request() when a poweroff is requested.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
typo in c021f8e65f.
comparison fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When several PCI bridges were in use, monitor command "info pci" would
enter into infinite loop. Buses behind the bridge were not discoverable
because secondary and subordinate bus numbers were not used properly.
Other buses were not found because bus search terminated on first miss.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The vmport "device" accesses the VCPU registers, so it requires proper
cpu_synchronize_state. Add it to vmport_ioport_read, which also
synchronizes vmport_ioport_write.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This provides the same information as reverted commit 2ba6edf0. Not
much, just better than nothing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Option "-device DRIVER,?" and monitor command "device_add DRIVER,?"
print the supported properties instead of creating a device. The
former also terminates the program.
This is commit 2ba6edf0 (just reverted) done right.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 2ba6edf0dd.
The commit has two issues:
* When it runs from the monitor, e.g. "device_add e1000,?", it prints
to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 922910ce42.
The commit has four issues:
* When it runs from the monitor, e.g. "device_add e1000,mac=?", it
prints to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,mac=?".
* It has an undocumented side effect on -global: "-global e1000.mac=?"
prints help, but only when we actually add an e1000 device.
* It does not work for properties that accept the value "?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Help was shoehorned into device creation, qdev_device_add(). Since
help doesn't create a device, it returns NULL, which looks to callers
just like failed device creation. Monitor handler do_device_add()
doesn't care, but main() exits unsuccessfully.
Move help out of device creation, into new qdev_device_help().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If an I/O request fails right away instead of getting an error only in the
callback, we still need to consider rerror/werror.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Current code assumes that only write requests are ever going to be restarted.
This is wrong since rerror=stop exists. Instead of directly starting writes,
use the same request processing as used for new requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We need a function that handles a single request. Create one by splitting out
code from virtio_blk_handle_output.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This fixes CONFIG_FB_CIRRUS for Linux guests and probably much more:
When switching away from linearly mapped vram, we also have to restore
the I/O handlers for the LFB.
This regression was once introduced by commit 2bec46dc97.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit enables one to use multiple virtio-serial devices and to
assign ports to arbitrary devices like this:
-device virtio-serial,id=foo -device virtio-serial,id=bar \
-device virtserialport,bus=foo.0,name=foo \
-device virtserialport,bus=bar.0,name=bar
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
sparc64 timer has tick counter which can be set and read,
and tick compare value used as deadline to fire timer interrupt.
The timer is not used as periodic timer, instead deadline
is set each time new timer interrupt is needed.
v3 -> v4:
- coding style
v2 -> v3:
- added missing timer debug output macro
- CPUTimer struct and typedef moved to cpu.h
- change CPU_SAVE_VERSION to 6, older save formats not supported
v1 -> v2:
- new conversion helpers cpu_to_timer_ticks and timer_to_cpu_ticks
- save offset from clock source to implement cpu_tick_set_count
- renamed struct sun4u_timer to CPUTimer
- load and save cpu timers
v0 -> v1:
- coding style
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Buffer block writes to avoid flushing every word access onto backing
storage device. This significantly speeds up flash emulation for flashes
connected through an 8 or 16-bit bus combined with backing storage (-pflash).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
When using ballooning to manage overcommitted memory on a host, a system for
guests to communicate their memory usage to the host can provide information
that will minimize the impact of ballooning on the guests. The current method
employs a daemon running in each guest that communicates memory statistics to a
host daemon at a specified time interval. The host daemon aggregates this
information and inflates and/or deflates balloons according to the level of
host memory pressure. This approach is effective but overly complex since a
daemon must be installed inside each guest and coordinated to communicate with
the host. A simpler approach is to collect memory statistics in the virtio
balloon driver and communicate them directly to the hypervisor.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Win32 suffers from a very big memory leak when dealing with SCSI devices.
Each read/write request allocates memory with qemu_memalign (ie
VirtualAlloc) but frees it with qemu_free (ie free).
Pair all qemu_memalign() calls with qemu_vfree() to prevent such leaks.
Signed-off-by: Herve Poussineau <hpoussin@reactos.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
PCI bridges' qdev info structures must indicate bridge header type,
otherwise critical bridge registers (esp. PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS, PCI_SUBORDINATE_BUS) will not be writable.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This file was renamed to ease the reviews of the recent changes
that went in.
Now that the changes are done, rename the file back to its original
name.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If migration takes place between write of the bmdma address register and
write of the command register (to initiate DMA), the destination will
not properly start the DMA op, hanging the guest:
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:16:41:00:00/00:00:00:00:00/e0 tag 0 dma 11264 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
Fix by sending current transfer information in the migration data.
We need to update ide version to 4 for this to work. As we don't
have subsectios, we need to chain the update increase until
vmstate_ide_pci (quintela)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit completes the do_pci_info() conversion to
QObject by adding support to PCI bridge devices.
This is done by recursively adding devices in the
"pci_bridge" key.
IMPORTANT: This code is being added separately because I could
NOT test it properly. According to Michael Tsirkin, it depends
on ultrasparc and it would take time to do the proper setup.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The returned QObject is a QList of all buses. Each bus is
represented by a QDict, which has a key with a QList of all
PCI devices attached to it. Each device is represented by
a QDict.
As has happended to other complex conversions, it's hard to
split this commit as part of it are new functions which are
called by each other.
IMPORTANT: support for printing PCI bridge attached devices
is NOT part of this commit, it's going to be added by the
next commit, as it's untested.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property value "?",
a help text will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,mac=?
and is already standard for other command line options.
A better help text could be provided by extending
the Property structure with a desc field.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When called with property "?", a list of supported
properties will be printed (instead of an error message).
This is useful for command lines like
qemu -device e1000,?
and was already standard for other options like model=?
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix HdrS offsets for Sparc64. The initrd address must be offset by
KERNBASE.
Use rom_ptr mechanism to actually write to the kernel image.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
When wcycle is non zero the area is already opened for readable IO.
Avoiding the re-registration of the memarea significantly speeds up
the flash emulation. In particular for flashes connected through 8 or
16-bit buses.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
Flashes connected through an 8 bit bus cannot handle write buffers
larger than 256 bytes.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
According to Sun4M System Architecture Manual chapter 5.3.2, a limit
of 0 will not generate interrupts.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Commit 930c86820e introduced a regression to eth_send: eth_tx_desc_put
manipulates the host's tx descriptor copy before writing it back, but
two lines down the descriptor is evaluated again, leaving us with an
invalid next address if host and guest endianness differ. So this was
the actual issue commit 2e87c5b937 tried to paper over.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Commit b3a219883e uncovered that we attached the Wolfson with an I2C
address shifted left by one. Fixing this makes sound work again for
the Musicpal.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: malc <av1474@comtv.ru>
Byte swap PCI config values.
Remove old bogus PCI config mechanism so that device 0:0.0 can be probed.
This requires OpenBIOS r667.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This commit enables the use of MSI interrupts for virtqueue
notifications for ports. We use nr_ports + 1 (for control channel) msi
entries for the ports, as only the in_vq operations need an interrupt on
the guest.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit adds a simple chardev-based serial port. Any data the guest
sends is forwarded to the chardev and vice-versa.
Sample uses for such a device can be obtaining info from the guest like
the file systems used, apps installed, etc. for offline usage and
logged-in users, clipboard copy-paste, etc. for online usage.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The port 'id' or number is internal state between the guest kernel and
our bus implementation. This is invocation-dependent and isn't part of
the guest-host ABI.
To correcly enumerate and map ports between the host and the guest, the
'name' property is used.
Example:
-device virtserialport,name=org.qemu.port.0
This invocation will get us a char device in the guest at:
/dev/virtio-ports/org.qemu.port.0
which can be a symlink to
/dev/vport0p3
This 'name' property is exposed by the guest kernel in a sysfs
attribute:
/sys/kernel/virtio-ports/vport0p3/name
A simple udev script can pick up this name and create the symlink
mentioned above.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Via control channel messages, the guest can tell us whether a port got
opened or closed. Similarly, we can also indicate to the guest of host
port open/close events.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit converts the virtio-console device to create a new
virtio-serial bus that can host console and generic serial ports. The
file hosting this code is now called virtio-serial-bus.c.
The virtio console is now a very simple qdev device that sits on the
virtio-serial-bus and communicates between the bus and qemu's chardevs.
This commit also includes a few changes to the virtio backing code for
pci and s390 to spawn the virtio-serial bus.
As a result of the qdev conversion, we get rid of a lot of legacy code.
The old-style way of instantiating a virtio console using
-virtioconsole ...
is maintained, but the new, preferred way is to use
-device virtio-serial -device virtconsole,chardev=...
With this commit, multiple devices as well as multiple ports with a
single device can be supported.
For multiple ports support, each port gets an IO vq pair. Since the
guest needs to know in advance how many vqs a particular device will
need, we have to set this number as a property of the virtio-serial
device and also as a config option.
In addition, we also spawn a pair of control IO vqs. This is an internal
channel meant for guest-host communication for things like port
open/close, sending port properties over to the guest, etc.
This commit is a part of a series of other commits to get the full
implementation of multiport support. Future commits will add other
support as well as ride on the savevm version that we bump up here.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
VIRTIO_PCI_QUEUE_MAX is redefined in hw/virtio.c. Let's just keep it in
hw/virtio.h.
Also, bump up the value of the maximum allowed virtqueues to 64. This is
in preparation to allow multiple ports per virtio-console device.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead of using the field 'readonly' of the BlockDriverState struct for passing the request,
pass the request in the flags parameter to the function.
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds compat property entries for ide-disk.ver and
scsi-disk.ver to pc-0.10 and pc-0.11. With this patch applied
the scsi and ide disks report "0.10" and "0.11" as version when
you start qemu with "-M pc-0.10" or "-M pc-0.11".
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to scsi-disk which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device lsi
-device scsi-disk,drive=disk,bus=scsi.0,unit=0,ver=42
You can also switch the version for all scsi drives using:
-global scsi-disk.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 747bbdf7 QEMU_WARN_UNUSED_RESULT is never defined as it is
conditional on a define from config-host.h which is included only later.
Include that file earlier to get the warnings back.
Reactivating it unfortunately leads to some warnings about unused qdev_init
results. These calls are changed to qdev_init_nofail to avoid build failures.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently we do not implement VLAN tagging for rtl8139(C+),
still data is read from ring buffer headers.
- augment unused assignment with TODO item
- cast txdw1 to void for now
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* Handling of multicast list was missing.
* Multicast all was missing.
* Promiscuous mode for multicast frames was wrong.
This patch is a step to synchronize my maintainer version
of eepro100.c (git://repo.or.cz/qemu/ar7.git) with the
version integrated in QEMU.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Handling of transmit commands is rather complex,
so about 80 lines of code were moved from function
action_command to the new function tx_command.
The two new values "tx" and "cb_address" in the
eepro100 status structure made this possible without
passing too many parameters.
In addition, the moved code was cleaned a little bit:
old comments marked with //~ were removed, C++ style
comments were replaced by C style comments, C++ like
variable declarations after code were reordered.
Simplified mode is still broken. Nor did I fix
endianess issues. Both problems will be fixed in
additional patches (which need this one).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Don't clear interrupts on disabling, because
* Sun4M_SystemArchitecture_edited2.pdf doesn't describe
that masking or un-masking IRQ shall clear pending ones.
* Field tests also show that SPARCstation-20 doesn't
clear them.
* The patch makes Solaris 2.5.1/2.6 boot ~1500 times
faster (~20 seconds instead of ~8 hours)
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Random reading depends on having the last row/page latched and not beeing
clobbered between read and any following random reads.
Also, s->iolen must be updated when loading the io/data register with
randomly accessed flash data.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
This patch adds hardware cursor feature to SM501 graphics chip emulation,
to make the graphic console more useful for QEMU SH4 users.
Signed-off-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As pointed out by clang size is only ever written to, but never actually
used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
clang-analyzer points out value assigned to 'len' is not used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although the value stored to 'addr' is used in the enclosing expression,
the value is never actually read from 'addr'.
Probably a typo.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
pci_get_byte, pci_get_word, pci_get_long and pci_get_quad
all take a const uint8_t pointer, because they only read
the configuration data.
Their prototypes should reflect this fact.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use new way to associate ROM files to devices.
Currently, there is only a ROM file for i82559er
included in QEMU, so the patch does not add
.romfile for the other devices.
When flexible mode is fixed in eepro100, adding
more ROM files will be possible. It should be
possible to create them from pxe-i82559er.bin,
because etherboot uses the same driver for all
eepro100 devices (only PCI ids differ).
Maybe it is even possible to create a single
pxe-i8255x.bin which supports all eepro100 devices
(not supported with current etherboot).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The numerical value was wrong (0x2800 instead of 0x0280)
which indeed did not make sense.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Mac feature bit isn't going to work as all network cards already have a
'mac' property to set the mac address. Remove it from mask and add in
get_features.
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Without this fix, guest crashes with drive=virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So '-M pc-0.10' and '-M pc-0.11' will use the fw_cfg rom load method
by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a pci bus property 'rombar' which specifies whenever
the pci rom should be loaded via pci rom bar (default) or via fw_cfg.
The later can be used for compatibility with older qemu versions where
no pci rom bar is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch changes the way rom loading via fw_cfg is handled.
Instead of having pc_init1() call a function which passed all
roms to the firmware config we simply pass a pointer to fw_cfg
to the rom loader.
Advantage: loading roms via firmware works also for devices which
are initialized after pc_init1(), i.e. everyting added via -device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- make dir argument mandatory, we allways have one anyway
(vgaroms or genroms).
- check for duplicates, skip loading if found.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
- Drop extra file argument from rom_add_file().
- Drop fw_dir check in do_info_roms, we allways have a dir name.
- code style fixes.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a new machine type for qemu 0.12.
Also fixup the 0.11 machine type: msi for virtio-blk-pci was enabled
after the 0.11 release, so turn it off in the 0.11 machine type.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since patch ed757e140c0ada220f213036e4497315d24ca8bct, virtio will
sometimes clear all status registers on bus master disable, which loses
information such as VIRTIO_CONFIG_S_FAILED bit. This is a result of
a patch being misapplied: code uses ! instead of ~ for bit
operations as in Yan's original patch. This obviously does not make
sense.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add feature bits as properties to virtio. This makes it possible to e.g. define
machine without indirect buffer support, which is required for 0.10
compatibility, or without hardware checksum support, which is required for 0.11
compatibility. Since default values for optional features are now set by qdev,
get_features callback has been modified: it sets non-optional bits, and clears
bits not supported by host.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename features->guest_features. This is
what they are, avoid confusion with
host features which we also need to keep around.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds "bit" property type, which is a boolean stored in a 32 bit
integer field, with legal values on and off. Will be used by virtio for
feature bits.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All callers of lsi_reselect have a lsi_request struct at hand anyway.
So just pass it directly instead of having lsi_reselect search for it
using the tag.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Right now lsi_request is allocated when a request is queued and released
when a request is unqueued. With this patch applied the lsi_request is
kept for the whole lifetime of the scsi request.
Rationale: We can use it for per-request data then. The patch does that
already for the request tag.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Replace the funky array logic for queued commands with standard
qemu list functions. Also rename lsi_queue to lsi_request.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Check that the cursor dimensions passed from the guest for the
DEFINE_CURSOR command don't overflow the available space in the
cursor.image[] or cursor.mask[] arrays before copying data from the
guest into those arrays.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
cpu_check_irqs
- handle SOFTINT register TICK and STICK timer bits
- only check interrupt levels greater than PIL value
- handle preemption by higher level traps
cpu_exec
- handle CPU_INTERRUPT_HARD only if interrupts are enabled
- PIL 15 is not special level on sparcv9
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move multiboot loading code into separate files as suggested by Alex Graf.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add generic support for debugging consoles (simple I/O ports which
when written to cause debugging output to be written to a target.)
The current implementation matches Bochs' port 0xe9, allowing the same
debugging code to be used for both Bochs and Qemu.
There is no vm state associated with the debugging port, simply
because it has none -- the entire interface is a single, stateless,
write-only port.
Most of the code was cribbed from the serial port driver.
v2: removed non-ISA variants (they can be introduced when/if someone
wants them, using code from the serial port); added configurable
readback (Bochs returns 0xe9 on a read from this register, mimic that
by default) This retains the apparently somewhat controversial user
friendly option, however.
v3: reimplemented the user friendly option as a synthetic option
("-debugcon foo" basically ends up being a parser-level shorthand for
"-chardev stdio,id=debugcon -device isa-debugcon,chardev=debugcon") --
this dramatically reduced the complexity while keeping the same level
of user friendliness.
v4: spaces, not tabs.
v5: update to match current top of tree. Calling qemu_chr_open()
already during parsing no longer works; defer until we are parsing the
other console-like devices.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
According to C99, realloc(non_null, 0) != free(non_null), that's why
it is forbidden in QEMU.
When there are no symbols, nsyms equals to 0. Free the syms structure
and set it to NULL instead of reallocating it with a size of 0.
This fixes -kernel with stripped kernels.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC i386-softmmu/pc.o
cc1: warnings being treated as errors
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c: In function 'load_multiboot':
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:614: error: ignoring return value of 'fread', declared with attribute warn_unused_result
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c: In function 'load_linux':
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:888: error: ignoring return value of 'fread', declared with attribute warn_unused_result
/usr/src/RPM/BUILD/qemu-0.11.92/hw/pc.c:889: error: ignoring return value of 'fread', declared with attribute warn_unused_result
make[1]: *** [pc.o] Error 1
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Store the register values in native endianness, by dropping all the
endianness conversion functions, and converting the endianness in
dbdma_readl/dbdma_writel instead.
Also guard the endianness conversion with TARGET_WORDS_BIGENDIAN to
simulate the backward connection of the bus.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Similarly to what has been done in e405a2ba91,
ignore rom intended to be loaded by the bios in find_rom() and rom_copy().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The first such option rom will load at address 0, which isn't very nice,
and the second will report a conflict and abort, which is horrible.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link to data sheet at intel.com so people can find it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use range helper function in i440fx_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Define symbolic value in i440fx configuration space
for 0x59, 0x5f and 0x7f and use them.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use range helper function in msix_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use range helper function in pm_write_config().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They call only pci_default_{read, write}_config().
So they aren't necessary.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
include pci_regs.h and remove duplicated defines.
And remove unused PCI_REVISION and PCI_SUBDEVICE_ID.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Import Linux pci_regs.h. Later PCI register definitions in pci.h
will be eliminated.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To match Linux PCI register definition,
rename PCI_SUBVENDOR_ID to PCI_SUBSYSTEM_VENDOR_ID.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCIBus::config_reg isn't used anymore, so remove it.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI_STATUS_DEVSEL is unused, and it also
has a different name in pci_regs.h
Remove.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
will be used by ensoniq emulation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change in meaningful ways.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
will be used by eepro100.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
No functional changes. I verified that the generated
object binary does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
Add core tile memeory to the RealView PBX-A9 board. Document the
memeory maps that are known to work with the qemu bootloader.
Signed-off-by: Paul Brook <paul@codesourcery.com>
For what I know DCR is always 32 bits wide, so we should also use uint32_t to
pass it along the stacks.
This fixes a warning when compiling qemu-system-ppc64 with KVM enabled, making
it compile without --disable-werror
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix the alternate time base the same way as the default timebase. SPR_ATBL
should return a 64-bit value on 64 bit implementations.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On PPC we have a 64-bit time base. Usually (PPC32) this is accessed using
two separate 32 bit SPR accesses to SPR_TBU and SPR_TBL.
On PPC64 the SPR_TBL register acts as 64 bit though, so we get the full
64 bits as return value. If we only take the lower ones, fine. But Linux
wants to see all 64 bits or it breaks.
This patch makes PPC64 Linux work even after TB crossed the 32-bit boundary,
which usually happened a few seconds after bootup.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Also change the New World default CPU to 970FX for ppc64,
since the G4 is a 32-bit CPU.
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
ROMs need to be loaded if they are anywhere in the requested area, not
only at the very beginning. This fixes Multiboot with ELF kernels that
have more than one program header.
Signed-off-by: Kevin Wolf <mail@kevin-wolf.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It was possible to load roms at address 0, but commit
632cf034b4 started to forbid that, which
broke at least ARM versatile.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When using the escc with Linux, we need interrupts. So instead of creating
a dummy device, let's just map them to the openpic we have anyways.
This makes Linux on PPC64 with console=ttyPZ0 work.
Obviously, this change needs to be reflected in openbios. Patch for that
follows this one. Please update the binary then.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When lowering an IRQ line, we search for the line we're supposed to lower.
Usually we run into an optimization there that queues up interrupts. This
queue ends with -1. Unfortunately we didn't set the first item to -1.
This patch fixes this, making interrupts work on PPC64.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Otherwise, the driver does not work in Linux after the INT_DISABLE changes in
PCI.
Michael Tsirkin had a patch to do this, I'm not sure what happened to it.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Convert musb fifo to 8bit to allow 8/16/32bit access
MUSB allows reading and writing to the fifo in 32/16/8 bit
width. The Linux kernel does this sometimes, most usually at
the end of writing the packet to allow packet to end at a
odd bytecount.
Convert the fifo to 8bit allows removing lots of shifts
which shows that the fifo is more natural as 8bit.
While at it, add multiple missing register definitions and
and cleanup debug prints.
Signed-off-by: Riku Voipio <riku.voipio@nokia.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that we load the option roms via fw_cfg, we can stop copying
them to the 0xc000 -> 0xe000. The patch does just that.
Also the rom loader gets simplified as all remaining users of the
rom loader load the bits at a fixed address so the packing and
aligning logic can go away.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
roms: use fw_cfg for vgabios and option rom loading, additionally to
deploying them the traditional way (copy to 0xc0000 -> 0xe0000 range).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a file transfer interface to fw_cfg. Intended to be
used for passing non-pci option roms and vgabios to seabios. Namespace
is modeled after the existing cbfs filesystem support in seabios.
Reading the new FW_CFG_FILE_DIR entry returns a file list.
Fields there are in network byte order (aka bigendian).
aliguori: fix fw_cfg.h for multiboot.bin, add proper fw_cfg.h declarations,
quiet fprintf() in fw_cfg.c
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a romfile property to the pci bus. It allows to specify
a romfile to load into the rom bar of the pci device. The default value
comes from a new field in PCIDeviceInfo. The property allows to change
the file and also to disable the rom loading using an empty string.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently, we preload option roms into the option rom space in memory. This
prevents DDIM from functioning correctly which severely limits the number
of roms we can support.
This patch introduces a pci_add_option_rom() which registers the
PCI_ROM_ADDRESS bar which points to our option rom. It also converts over
the cirrus vga adapter, the rtl8139, virtio, and the e1000 to use this
new mechanism.
The result is that PXE boot functions even with three unique types of cards.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
SCSI controllers have no trouble existing without any attached
disks. This could be achieved with the (legacy) monitor syntax
pci_add pci_addr=auto storage if=scsi
This is now denied with
scsi requires a backing file/device.
failed to add if=scsi
There is no need for this denial and it breaks compatability
with existing QEMU usage, so remove the check for presence
of a drive.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
