All other peripherals' IRQs are in the format of decimal value.
Change SIFIVE_U_GEM_IRQ to be consistent.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
Instead of using string compares to determine if a RISC-V machine is
using 32-bit or 64-bit CPUs we can use the initalised CPUs. This avoids
us having to maintain a list of CPU names to compare against.
This commit also fixes the name of the function to match the
riscv_cpu_is_32bit() function.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 8ab7614e5df93ab5267788b73dcd75f9f5615e82.1608142916.git.alistair.francis@wdc.com
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Somehow HSS needs to access address 0 [1] for the DDR calibration data
which is in the chipset's reserved memory. Let's map it.
[1] See the config_copy() calls in various places in ddr_setup() in
the HSS source codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-9-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of loading the kernel at a hardcoded start address, let's load
the kernel at the next aligned address after the end of the firmware.
This should have no impact for current users of OpenSBI, but will
allow loading a noMMU kernel at the start of memory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 46c00c4f15b42feb792090e3d74359e180a6d954.1602634524.git.alistair.francis@wdc.com
Instead of returning the unused entry address from riscv_load_firmware()
instead return the end address. Also return the end address from
riscv_find_and_load_firmware().
This tells the caller if a firmware was loaded and how big it is. This
can be used to determine the load address of the next image (usually the
kernel).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 558cf67162342d65a23262248b040563716628b2.1602634524.git.alistair.francis@wdc.com
Allow the user to specify the main application CPU for the sifive_u
machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: b8412086c8aea0eff30fb7a17f0acf2943381b6a.1602634524.git.alistair.francis@wdc.com
Some of the enum constant names conflict with the QOM type check
macros (SIFIVE_U_OTP, SIFIVE_U_PRCI). This needs to be addressed
to allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_U_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with a QOM type check
macro (SIFIVE_E_PRCI). This needs to be addressed to allow us to
transform the QOM type check macros into functions generated by
OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_E_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timestamp is using a hard-coded timebase
frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be
true for all boards.
Add a new 'timebase-freq' property to the CLINT device, and
update various functions to accept this as a parameter.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-16-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems
enough to create unimplemented devices to cover their register
spaces at this point.
With this commit, QEMU can boot to U-Boot (2nd stage bootloader)
all the way to the Linux shell login prompt, with a modified HSS
(1st stage bootloader).
For detailed instructions on how to create images for the Icicle
Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-15-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 2 Candence GEMs to provide
IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.
On the Icicle Kit board, GEM0 connects to a PHY at address 8 while
GEM1 connects to a PHY at address 9.
The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we
must specify 2 '-nic' options from the command line in order to get
a working ethernet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-14-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates one Cadence SDHCI controller.
On the Icicle Kit board, one eMMC chip and an external SD card
connect to this controller depending on different configuration.
As QEMU does not support eMMC yet, we just emulate the SD card
configuration. To test this, the Hart Software Services (HSS)
should choose the SD card configuration:
$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es
The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp
Note the generated SD card image should be resized before use:
$ qemu-img resize /path/to/sdcard.img 4G
Launch QEMU with the following command:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board
wires 4 of them out. Let's connect all 5 MMUARTs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V machines do not instantiate RISC-V CPUs directly, instead
they do that via the hart array. Add a new property for the reset
vector address to allow the value to be passed to the CPU, before
CPU is realized.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (IBEX_PLIC, IBEX_UART). This needs to be addressed to
allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to IBEX_DEV_*, to avoid conflicts.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-8-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We extend RISC-V virt machine to allow creating a multi-socket
machine. Each RISC-V virt machine socket is a NUMA node having
a set of HARTs, a memory instance, a CLINT instance, and a PLIC
instance. Other devices are shared between all sockets. We also
update the generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V virt
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V virt machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-6-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend RISC-V spike machine to allow creating a multi-socket
machine. Each RISC-V spike machine socket is a NUMA node having
a set of HARTs, a memory instance, and a CLINT instance. Other
devices are shared between all sockets. We also update the
generated device tree accordingly.
By default, NUMA multi-socket support is disabled for RISC-V spike
machine. To enable it, users can use "-numa" command-line options
of QEMU.
Example1: For two NUMA nodes with 2 CPUs each, append following
to command-line options: "-smp 4 -numa node -numa node"
Example2: For two NUMA nodes with 1 and 3 CPUs, append following
to command-line options:
"-smp 4 -numa node -numa node -numa cpu,node-id=0,core-id=0 \
-numa cpu,node-id=1,core-id=1 -numa cpu,node-id=1,core-id=2 \
-numa cpu,node-id=1,core-id=3"
The maximum number of sockets in a RISC-V spike machine is 8
but this limit can be changed in future.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-5-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We add common helper routines which can be shared by RISC-V
multi-socket NUMA machines.
We have two types of helpers:
1. riscv_socket_xyz() - These helper assist managing multiple
sockets irrespective whether QEMU NUMA is enabled/disabled
2. riscv_numa_xyz() - These helpers assist in providing
necessary QEMU machine callbacks for QEMU NUMA emulation
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Message-Id: <20200616032229.766089-4-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend PLIC emulation to allow multiple instances of PLIC in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from PLIC emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200616032229.766089-3-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend CLINT emulation to allow multiple instances of CLINT in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from CLINT emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-Id: <20200616032229.766089-2-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
