With the LEON3 IRQ controller IRQs can be acknowledged 2 ways:
* Explicitly by software writing to the CLEAR_OFFSET register
* Implicitly when the procesor is done running the trap handler attached
to the IRQ.
The actual IRQMP code only allows the implicit processor triggered IRQ ack.
If software write explicitly to the CLEAR_OFFSET register, this will clear
the pending bit in the register value but this will not lower the ongoing
raised IRQ with the processor. The IRQ will be kept raised to the LEON
processor until the related trap handler is run and the processor implicitly
ack the interrupt. So with the actual IRQMP code trap handler have to be run
even if the software has already done its job by clearing the pending bit.
This feature has been tested on another LEON3 simulator (tsim_leon3 from
Gaisler) and it turns out that the Qemu implementation is not equivalent to
the tsim one. In tsim, if software does clear a pending interrupt before
the related interrupt handler is triggered the said interrupt handler will
not be called.
This patch brings the Qemu IRQMP implementation in line with the tsim
implementation by allowing IRQ to be acknowledged by software only.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Configurable Fault Status Register for ARMv7M and v8M is
supposed to be byte and halfword accessible, but we were only
implementing word accesses. Add support for the other access
sizes, which are used by the Zephyr RTOS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512742372-31517-1-git-send-email-peter.maydell@linaro.org
The GICv2 specification says that reserved register addresses
must RAZ/WI; now that we implement external abort handling
for Arm CPUs this means we must return MEMTX_OK rather than
MEMTX_ERROR, to avoid generating a spurious guest data abort.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
The GICv3 specification says that reserved register addresses
should RAZ/WI. This means we need to return MEMTX_OK, not MEMTX_ERROR,
because now that we support generating external aborts the
latter will cause an abort on new board models.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This patch adds the function apic_get_highest_priority_irr to
apic.c and exports it through the interface in apic.h for use by hvf.
Signed-off-by: Sergio Andres Gomez Del Real <Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-8-Sergio.G.DelReal@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now both classes (i8259, i8259-kvm) support this. Move this upper to
the common class code.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-6-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's leverage the i8259 common code for kvm-i8259 too.
I think it's still possible that stats can lost when i8259 is in kernel
and meanwhile when irqfd is used, e.g., by vfio or vhost devices.
However that should be rare IMHO since they should be using MSIs mostly
if they really want performance (that's why people use vhost and device
assignment), and no old INTx should be used. As long as the INTx users
are emulated in QEMU the stats will be correct.
For "info pic", it should be always accurate since we fetch kvm regs
before dump.
More importantly, it's just too simple to do this now - it's only 10+
LOC to gain this feature.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-5-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was only for userspace i8259. Move it to general code so that
kvm-i8259 can also use it in the future.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's not really scary to even enable it forever. After all it's i8259,
and it's even not the kernel one.
Then we can remove quite a few of lines to make it cleaner. And "info
irq" will always work for it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One thing to mention is that in pic_set_irq() I need to uncomment a few
lines in the macros to make sure IRQ value calculation is correct.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-2-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xics_get_qirq() is only used by the sPAPR machine. Let's move it there
and change its name to reflect its scope. It will be useful for XIVE
support which will use its own set of qirqs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the prototype to use a sPAPRMachineState and prefix them
with spapr_irq_. It will let us synchronise the IRQ allocation with
the XIVE interrupt mode when available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'intc' pointer of the CPU references the interrupt presenter in
the XICS interrupt mode. When the XIVE interrupt mode is available and
activated, the machine will need to reassign this pointer to reflect
the change.
Moving this assignment under the realize routine of the CPU will ease
the process when the interrupt mode is toggled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR and the PowerNV core objects create the interrupt presenter
object of the CPUs in a very similar way. Let's provide a common
routine in which we use the presenter 'type' as a child identifier.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace *printf() with *_report().
Remove trailing new lines.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The previous code section uses a 'first < 0' test and returns. Therefore,
there is no need to test the 'first' variable against '>= 0' afterwards.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the v8M security extension, there should be two systick
devices, which use separate banked systick exceptions. The
register interface is banked in the same way as for other
banked registers, including the existence of an NS alias
region for secure code to access the nonsecure timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-3-git-send-email-peter.maydell@linaro.org
Generalize nvic_sysreg_ns_ops so that we can pass it an
arbitrary MemoryRegion which it will use as the underlying
register implementation to apply the NS-alias behaviour
to. We'll want this so we can do the same with systick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-2-git-send-email-peter.maydell@linaro.org
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the very beginning, post_load() was called from common
reset. This is not standard and obliged to discriminate the
reset case from the restore case using the iidr value.
Let's get rid of that call.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix an incorrect mask expression in the handling of v7M MPU_RBAR
reads that meant that we would always report the ADDR field as zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1509732813-22957-1-git-send-email-peter.maydell@linaro.org
Remove the last few DPRINTFs from hw/intc/ioapic.c and turn
them into tracing. In one case it's a new trace, in the others
it's just adding a parameter to the existing traces.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171102180310.24760-1-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using the emulated XICS, the 'info pic' monitor command shows:
CPU 0 XIRR=ff000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10040060340
1000 MSI 05 00
1001 MSI 05 00
1002 MSI 05 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI 05 00
1009 MSI 05 00
100a MSI 05 00
100b MSI 05 00
100c MSI 05 00
but when using the in-kernel XICS with the very same guest, we get:
CPU 0 XIRR=00000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10032e00340
1000 MSI ff 00
1001 MSI ff 00
1002 MSI ff 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI ff 00
1009 MSI ff 00
100a MSI ff 00
100b MSI ff 00
100c MSI ff 00
ie, all irqs are masked and XIRR is null, while we should get the
same output as with the emulated XICS.
If the guest is then migrated, 'info pic' shows the expected values
on both source and destination.
The problem is that QEMU doesn't synchronize with KVM before printing
the XICS state. Migration happens to fix the output because it enforces
synchronization with KVM.
To fix the invalid output of 'info pic', this patch introduces a new
synchronize_state operation for both ICPStateClass and ICSStateClass.
The ICP operation relies on run_on_cpu() in order to kick the vCPU
and avoid sleeping on KVM_GET_ONE_REG.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS is not fully properly reset at the moment. Caches are
not emptied.
After a reset, in case we attempt to save the state before
the bound devices have registered their MSIs and after the
1st level table has been allocated by the ITS driver
(device BASER is valid), the first level entries are still
invalid. If the device cache is not empty (devices registered
before the reset), vgic_its_save_device_tables fails with -EINVAL.
This causes a QEMU abort().
Cc: qemu-stable@nongnu.org
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The commit cddafd8f35 ("hw/intc/arm_gicv3_its: Implement state save
/restore") breaks the backward compatibility with the older kernels
where vITS save/restore support is not available. The vmstate function
vm_change_state_handler() should not be registered if the running kernel
doesn't support ITS save/restore feature. Otherwise VM instance will be
killed whenever vmstate callback function is invoked.
Observed a virtual machine shutdown with QEMU-2.10+linux-4.11 when testing
the reboot command "virsh reboot <domain> --mode acpi" instead of reboot.
KVM Error: 'KVM_SET_DEVICE_ATTR failed: Group 4 attr 0x00000000000001'
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1509712671-16299-1-git-send-email-shankerd@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add OpenRISC Multicore PIC which handles inter processor interrupts
(IPI) between cores. In OpenRISC all device interrupts are routed to
each core enabling this device to be simple.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
This calculation of the first exception vector in
the ITNS<n> register being accessed:
int startvec = 32 * (offset - 0x380) + NVIC_FIRST_IRQ;
is incorrect, because offset is in bytes, so we only want
to multiply by 8.
Spotted by Coverity (CID 1381484, CID 1381488), though it is
not correct that it actually overflows the buffer, because
we have a 'startvec + i < s->num_irq' guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507650856-11718-1-git-send-email-peter.maydell@linaro.org
Coverity points out that we forgot the 'break' for
the SAU_CTRL write case (CID1381683). This has
no actual visible consequences because it happens
that the following case is effectively a no-op.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1507742676-9908-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
When we added support for the new SHCSR bits in v8M in commit
437d59c17e the code to support writing to the new HARDFAULTPENDED
bit was accidentally only added for non-secure writes; the
secure banked version of the bit should also be writable.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-21-git-send-email-peter.maydell@linaro.org
Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Reset for devices does not include an automatic clear of the
device state (unlike CPU state, where most of the state
structure is cleared to zero). Add some missing initialization
of NVIC state that meant that the device was left in the wrong
state if the guest did a warm reset.
(In particular, since we were resetting the computed state like
s->exception_prio but not all the state it was computed
from like s->vectors[x].active, the NVIC wound up in an
inconsistent state that could later trigger assertion failures.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1506092407-26985-2-git-send-email-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZy64HAAoJEAUWMx68W/3nTqwP/A5Gx4Qwkv5KKdpM0YLq//d+
OODmzl7Ni3a5Up1ETqGdLb84estrgY+5DISp73Rkt4a5tbT7+XKrhb4qD+93NnTe
zynY9in4C1jGxYm7YzeOhwSeIiuLZMTCLQlGdYw7/nunIFwkItUEvAFx3AG1WCJe
2Mk0lvmg4LikruDDMdzqZaJu7h5RU5sQjA7SsyrTBdsN7tNWl3rKLYGXwgzv0uz5
n2xkUgzvvnj1Bk/Adojkn05yxA86xKD/4rhFED9fjNVSjAGHMrHIWOJ70V26Cg5w
3gJ+5mesWsH+erf0JFYv0S38SyFbmIOE39Nn13D/d0o1x89P8B8cgqbi3ADTKM77
875wuIVnZzi2vIwVdxXQ9GHQ79cpXwr2fOfQ2rjT6Ll95K+u/MQG86fQiO0eJW+0
KwQVCwwh+HmCUcCogMuxAc9+F8C8qolwCi/9QXwS2yLBElHKaWDIMyTce36cW9d7
cZaKIOeSJUGNFoaWZnXN88MRuOYbdywTl+GddVAW3+VJCTYV2oi0o5fsTfxXy5AV
y7uYo/pcSj2gSZJ5GairMlB6p5iXnE8yusi1e4ZKA1x1TaSHSb6zR59lRUFr+j/L
JhUCfA85v5/elGqgkYp6UhSzFDJ2ID2oSEMQTIzfVrinOXtnf2KEh33YMbUH5qyo
yHVEu12uPe9rE6A0vWlu
=/+LV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170927a' into staging
Migration pull 2017-09-27
# gpg: Signature made Wed 27 Sep 2017 14:56:23 BST
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170927a:
migration: Route more error paths
migration: Route errors up through vmstate_save
migration: wire vmstate_save_state errors up to vmstate_subsection_save
migration: Check field save returns
migration: check pre_save return in vmstate_save_state
migration: pre_save return int
migration: disable auto-converge during bulk block migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Apple uses an IBM MPIC2A without timers, it has 64 sources.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq()
to handle banked exceptions:
* acknowledge needs to use the correct vector, which may be
in sec_vectors[]
* acknowledge needs to return to its caller whether the
exception should be taken to secure or non-secure state
* complete needs its caller to tell it whether the exception
being completed is a secure one or not
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org
Handle banking of SHCSR: some register bits are banked between
Secure and Non-Secure, and some are only accessible to Secure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-19-git-send-email-peter.maydell@linaro.org
The ICSR NVIC register is banked for v8M. This doesn't
require any new state, but it does mean that some bits
are controlled by BFHNFNMINS and some bits must work
with the correct banked exception. There is also a new
in v8M PENDNMICLR bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-18-git-send-email-peter.maydell@linaro.org
Now that we have a banked FAULTMASK register and banked exceptions,
we can implement the correct check in cpu_mmu_index() for whether
the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes
handlers which have requested a negative execution priority to run
with the MPU disabled. In v8M the test has to check this for the
current security state and so takes account of banking.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org
Update nvic_exec_prio() to support the v8M changes:
* BASEPRI, FAULTMASK and PRIMASK are all banked
* AIRCR.PRIS can affect NS priorities
* AIRCR.BFHFNMINS affects FAULTMASK behaviour
These changes mean that it's no longer possible to
definitely say that if FAULTMASK is set it overrides
PRIMASK, and if PRIMASK is set it overrides BASEPRI
(since if PRIMASK_NS is set and AIRCR.PRIS is set then
whether that 0x80 priority should take effect or the
priority in BASEPRI_S depends on the value of BASEPRI_S,
for instance). So we switch to the same approach used
by the pseudocode of working through BASEPRI, PRIMASK
and FAULTMASK and overriding the previous values if
needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-16-git-send-email-peter.maydell@linaro.org
If AIRCR.BFHFNMINS is clear, then although NonSecure HardFault
can still be pended via SHCSR.HARDFAULTPENDED it mustn't actually
preempt execution. The simple way to achieve this is to clear the
enable bit for it, since the enable bit isn't guest visible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-15-git-send-email-peter.maydell@linaro.org
In v7M, the fixed-priority exceptions are:
Reset: -3
NMI: -2
HardFault: -1
In v8M, this changes because Secure HardFault may need
to be prioritised above NMI:
Reset: -4
Secure HardFault if AIRCR.BFHFNMINS == 1: -3
NMI: -2
Secure HardFault if AIRCR.BFHFNMINS == 0: -1
NonSecure HardFault: -1
Make these changes, including support for changing the
priority of Secure HardFault as AIRCR.BFHFNMINS changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-14-git-send-email-peter.maydell@linaro.org
When escalating to HardFault, we must go into Lockup if we
can't take the synchronous HardFault because the current
execution priority is already at or below the priority of
HardFault. In v7M HF is always priority -1 so a simple < 0
comparison sufficed; in v8M the priority of HardFault can
vary depending on whether it is a Secure or NonSecure
HardFault, so we must check against the priority of the
HardFault exception vector we're about to use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-13-git-send-email-peter.maydell@linaro.org
In armv7m_nvic_set_pending() we have to compare the
priority of an exception against the execution priority
to decide whether it needs to be escalated to HardFault.
In the specification this is a comparison against the
exception's group priority; for v7M we implemented it
as a comparison against the raw exception priority
because the two comparisons will always give the
same answer. For v8M the existence of AIRCR.PRIS and
the possibility of different PRIGROUP values for secure
and nonsecure exceptions means we need to explicitly
calculate the vector's group priority for this check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-12-git-send-email-peter.maydell@linaro.org
Make the set_prio() function take a bool indicating
whether to pend the secure or non-secure version of a banked
interrupt, and use this to implement the correct banking
semantics for the SHPR registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-11-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
Update the nvic_recompute_state() code to handle the security
extension and its associated banked registers.
Code that uses the resulting cached state (ie the irq
acknowledge and complete code) will be updated in a later
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-9-git-send-email-peter.maydell@linaro.org
For v8M, the NVIC has a new set of registers per interrupt,
NVIC_ITNS<n>. These determine whether the interrupt targets Secure
or Non-secure state. Implement the register read/write code for
these, and make them cause NVIC_IABR, NVIC_ICER, NVIC_ISER,
NVIC_ICPR, NVIC_IPR and NVIC_ISPR to RAZ/WI for non-secure
accesses to fields corresponding to interrupts which are
configured to target secure state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-8-git-send-email-peter.maydell@linaro.org
Update the code in nvic_rettobase() so that it checks the
sec_vectors[] array as well as the vectors[] array if needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-7-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
Instead of looking up the pending priority
in nvic_pending_prio(), cache it in a new state struct
field. The calculation of the pending priority given
the interrupt number is more complicated in v8M with
the security extension, so the caching will be worthwhile.
This changes nvic_pending_prio() from returning a full
(group + subpriority) priority value to returning a group
priority. This doesn't require changes to its callsites
because we use it only in comparisons of the form
execution_prio > nvic_pending_prio()
and execution priority is always a group priority, so
a test (exec prio > full prio) is true if and only if
(execprio > group_prio).
(Architecturally the expected comparison is with the
group priority for this sort of "would we preempt" test;
we were only doing a test with a full priority as an
optimisation to avoid the mask, which is possible
precisely because the two comparisons always give the
same answer.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-5-git-send-email-peter.maydell@linaro.org
With banked exceptions, just the exception number in
s->vectpending is no longer sufficient to uniquely identify
the pending exception. Add a vectpending_is_s_banked bool
which is true if the exception is using the sec_vectors[]
array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1505240046-11454-4-git-send-email-peter.maydell@linaro.org
For the v8M security extension, some exceptions must be banked
between security states. Add the new vecinfo array which holds
the state for the banked exceptions and migrate it if the
CPU the NVIC is attached to implements the security extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
-----BEGIN PGP SIGNATURE-----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=GAd3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20170915' into staging
ppc patch queue 2017-09-15
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
# gpg: Signature made Fri 15 Sep 2017 04:50:00 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20170915:
ppc/kvm: use kvm_vm_check_extension() in kvmppc_is_pr()
spapr_events: use QTAILQ_FOREACH_SAFE() in spapr_clear_pending_events()
spapr_cpu_core: cleaning up qdev_get_machine() calls
spapr_pci: don't create 64-bit MMIO window if we don't need to
spapr_pci: convert sprintf() to g_strdup_printf()
spapr_cpu_core: fail gracefully with non-pseries machine types
xics: fix several error leaks
vfio, spapr: Fix levels calculation
spapr_pci: handle FDT creation errors with _FDT()
spapr_pci: use the common _FDT() helper
spapr: fix CAS-generated reset
ppc/xive: fix OV5_XIVE_EXPLOIT bits
spapr: only update SDR1 once per-cpu during CAS
spapr_pci: use g_strdup_printf()
spapr_pci: drop useless check in spapr_populate_pci_child_dt()
spapr_pci: drop useless check in spapr_phb_vfio_get_loc_code()
hw/ppc/spapr.c: cleaning up qdev_get_machine() calls
net: Add SunGEM device emulation as found on Apple UniNorth
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If object_property_get_link() fails then it allocates an error, which
must be freed before returning. The error_get_pretty() function is
merely an accessor to the error message and doesn't free anything.
The error.h header indicates how to do it right:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In several places we were unconditionally applying the
nvic_gprio_mask() to a priority value. This is incorrect
if the priority is one of the fixed negative priority
values (for NMI and HardFault), so don't do it.
This bug would have caused both NMI and HardFault to be
considered as the same priority and so NMI wouldn't
correctly preempt HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505137930-13255-5-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
For v8M the range 0xe002e000..0xe002efff is an alias region which
for secure accesses behaves like a NonSecure access to the main
SCS region. (For nonsecure accesses including when the security
extension is not implemented, it is RAZ/WI.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-11-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
Fix the following warning:
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: warning: logical not is only applied to the left hand side of this bitwise operator [-Wlogical-not-parentheses]
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^ ~
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses after the '!' to evaluate the bitwise operator first
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses around left hand side expression to silence this warning
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
This logic error meant we were not setting the PTZ
bit when we should -- luckily as the comment suggests
this wouldn't have had any effects beyond making GIC
initialization take a little longer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Message-id: 20170829173226.7625-1-bobby.prani@gmail.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARMv7M architecture specifies that most of the addresses in the
PPB region (which includes the NVIC, systick and system registers)
are not accessible to unprivileged accesses, which should
BusFault with a few exceptions:
* the STIR is configurably user-accessible
* the ITM (which we don't implement at all) is always
user-accessible
Implement this by switching the register access functions
to the _with_attrs scheme that lets us distinguish user
mode accesses.
This allows us to pull the handling of the CCR.USERSETMPEND
flag up to the level where we can make it generate a BusFault
as it should for non-permitted accesses.
Note that until the core ARM CPU code implements turning
MEMTX_ERROR into a BusFault the registers will continue to
act as RAZ/WI to user accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-16-git-send-email-peter.maydell@linaro.org
The armv7m_nvic.h header file was accidentally placed in
include/hw/arm; move it to include/hw/intc to match where
its corresponding .c file lives.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-15-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
Remove an out of date comment which says there's only one
item in the NVIC container region -- we put systick into its
own device object a while back and so now there are two
things in the container.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-6-git-send-email-peter.maydell@linaro.org
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During migration we should transfer ais states to the target guest.
This patch introduces a subsection to kvm_s390_flic_vmstate and new
vmsd for qemu_flic. The ais states need to be migrated only when
ais is supported.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
zPCI instructions and facilities are available since IBM zEnterprise
EC12. To support z/PCI in QEMU we enable zpci, aen and ais facilities
starting with zEC12 GA1. And we always set zpci and aen bits in max cpu
model. Later they might be switched off due to applied real cpu model.
For ais bit, we only provide it in the full cpu model beginning with
zEC12 and defer its enablement in the default cpu model to a later point
in time. At the same time, disable them for 2.9 and older machines.
Because of introducing AIS facility, we could check if it's enabled to
initialize flic->ais_supported with the real value.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Although we have recently vmstatified the migration of some css
infrastructure, for some css entities there is still state to be
migrated left, because the focus was keeping migration stream
compatibility (that is basically everything as-is).
Let us add vmstate helpers and extend existing vmstate descriptions so
that we have everything we need. Let us guard the added state via
css_migration_enabled, so we keep the compatible behavior if css
migration is disabled.
Let's also annotate the bits which do not need to be migrated for better
readability.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170711145441.33925-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's introduce a specialized way to inject adapter interrupts that,
unlike the common interrupt injection method, allows to take the
characteristics of the adapter into account.
For adapters subject to AIS facility:
- for non-kvm case, we handle the suppression for a given ISC in QEMU.
- for kvm case, we pass adapter id to kvm to do airq injection.
Add add tracepoint for suppressed airq and suppressing airq.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to emulate the adapter interruption suppression (AIS)
facility properly, the guest needs to be able to modify the AIS mask.
Interrupt suppression will be handled via the flic (for kvm, via a
recently introduced kernel backend; for !kvm, in the flic code), so
let's introduce a method to change the mode via the flic interface.
We introduce the 'simm' and 'nimm' fields to QEMUS390FLICState
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Co-authored-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit f6f4ce4211 ("s390x: add property adapter_routes_max_batch",
2016-12-09) introduces a common realize (intended to be common for all
the subclasses) for flic, but fails to make sure the kvm-flic which had
its own is actually calling this common realize.
This omission fortunately does not result in a grave problem. The common
realize was only supposed to catch a possible programming mistake by
validating a value of a property set via the compat machine macros. Since
there was no programming mistake we don't need this fixed for stable.
Let's fix this problem by making sure kvm flic honors the realize of its
parent class.
Let us also improve on the error message we would hypothetically emit
when the validation fails.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: f6f4ce4211 ("s390x: add property adapter_routes_max_batch")
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
From the moment it was introduced by commit a2875e6f98 ("s390x/kvm:
implement floating-interrupt controller device", 2013-07-16) the kvm-flic
is not making realize fail properly in case it's impossible to create the
KVM device which basically serves as a backend and is absolutely
essential for having an operational kvm-flic.
Let's fix this by making sure we do proper error propagation in realize.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: a2875e6f98 "s390x/kvm: implement floating-interrupt controller device"
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's vmstatify virtio_ccw_save_config and virtio_ccw_load_config for
flexibility (extending using subsections) and for fun.
To achieve this we need to hack the config_vector, which is VirtIODevice
(that is common virtio) state, in the middle of the VirtioCcwDevice state
representation. This is somewhat ugly, but we have no choice because the
stream format needs to be preserved.
Almost no changes in behavior. Exception is everything that comes with
vmstate like extra bookkeeping about what's in the stream, and maybe some
extra checks and better error reporting.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170703213414.94298-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Previously QEMU open-pic implemented the 4 open-pic timers including
all timer registers, but the timers did not "count" or generate any
interrupts. The patch makes the timers both count and generate
interrupts. The timer clock frequency is fixed at 25MHZ.
--
Responding to V2 patch comments.
- Simplify clock frequency logic and commentary.
- Remove camelCase variables.
- Timer objects now created at init rather than lazily.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICPState objects are currently registered to vmstate as qdev objects.
Their instance ids are hence computed automatically in the migration code,
and thus depends on the order the CPU cores were plugged.
If the destination had its CPU cores plugged in a different order than the
source, then ICPState objects will have different instance_ids and load
the wrong state.
Since CPU objects have a reliable cpu_index which is already used as
instance_id in vmstate, let's use it for ICPState as well.
Please note that this doesn't break migration. Older machine types used to
allocate and realize all ICPState objects at machine init time, for the whole
lifetime of the machine. The qdev instance ids are thus 0,1,2... nr_servers
and happen to map to the vCPU indexes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In some cases a failing VMSTATE_*_EQUAL does not mean we detected a bug,
but it's actually the best we can do. Especially in these cases a verbose
error message is required.
Let's introduce infrastructure for specifying a error hint to be used if
equal check fails. Let's do this by adding a parameter to the _EQUAL
macros called _err_hint. Also change all current users to pass NULL as
last parameter so nothing changes for them.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170623144823.42936-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
TYPE_ARM_CPU's property "mp-affinity" is defined with
DEFINE_PROP_UINT64().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-35-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The getter and setter of TYPE_APIC_COMMON property "id" are
apic_common_get_id() and apic_common_set_id().
apic_common_get_id() reads either APICCommonState member uint32_t
initial_apic_id or uint8_t id into an int64_t local variable. It then
passes this variable to visit_type_int().
apic_common_set_id() uses visit_type_int() to read the value into a
local variable, which it then assigns both to initial_apic_id and id.
While the state backing the property is two unsigned members, 8 and 32
bits wide, the actual visitor is 64 bits signed.
Change getter and setter to use visit_type_uint32(). Then everything's
uint32_t, except for @id.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-19-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We change the restoration priority of both the GICv3 and ITS. The
GICv3 must be restored before the ITS and the ITS needs to be restored
before PCIe devices since it translates their MSI transactions.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 1497023553-18411-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the flush of the LPI pending bits into the
redistributor pending tables. This happens on VM stop.
There is no explicit restore as the tables are implicitly sync'ed
on ITS table restore and on LPI enable at redistributor level.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We need to handle both registers and ITS tables. While
register handling is standard, ITS table handling is more
challenging since the kernel API is devised so that the
tables are flushed into guest RAM and not in vmstate buffers.
Flushing the ITS tables on device pre_save() is too late
since the guest RAM is already saved at this point.
Table flushing needs to happen when we are sure the vcpus
are stopped and before the last dirty page saving. The
right point is RUN_STATE_FINISH_MIGRATE but sometimes the
VM gets stopped before migration launch so let's simply
flush the tables each time the VM gets stopped.
For regular ITS registers we just can use vmstate pre_save()
and post_load() callbacks.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-3-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In some circumstances, we don't want to abort if the
kvm_device_access fails. This will be the case during ITS
migration, in case the ITS table save/restore fails because
the guest did not program the vITS correctly. So let's pass an
error object to the function and return the ioctl value. New
callers will be able to make a decision upon this returned
value.
Existing callers pass &error_abort which will cause the
function to abort on failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 1497023553-18411-2-git-send-email-eric.auger@redhat.com
[PMM: wrapped long line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The static array of interrupt combiner mappings is not modified so it
can be made const for code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are to SysBusDevice variables in exynos4210_gic_realize()
function: one for the device itself and second for arm_gic device. Add
a prefix "gic" to the second one so it will be easier to understand the
code.
While at it, put local uninitialized 'i' variable at the end, next to
other uninitialized ones.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cpu_setup() handler is only implemented by xics_kvm, where it really
does a typical "realize" job. Moreover, the realize() handler is called
shortly after cpu_setup(), on the same path.
This patch converts xics_kvm to implement realize() instead of cpu_setup().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Until recently, spapr used to allocate ICPState objects for the lifetime
of the machine. They would only be associated to vCPUs in xics_cpu_setup()
when plugging a CPU core.
Now that ICPState objects have the same lifecycle as vCPUs, it is
possible to associate them during realization.
This patch hence open-codes xics_cpu_setup() in icp_realize(). The vCPU
is passed as a property. Note that vCPU now needs to be realized first
for the IRQs to be allocated. It also needs to resetted before ICPState
realization in order to synchronize with KVM.
Since ICPState objects are freed when unrealized, xics_cpu_destroy() isn't
needed anymore and can be safely dropped.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It makes more sense to pass an IPCState * to handlers of ICPStateClass
instead of a DeviceState *, if only to benefit from compile time type
checking. The same goes with ICSStateClass.
While here, we also change the declaration of ICPStateClass in xics.h
for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These properties are part of the XICS API. They deserve to appear
explicitely in the XICS header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Taking into account that qemu_set_irq() returns immediatly if its first
argument is NULL, icp_kvm_reset() largely duplicates icp_reset().
This patch introduces a reset() handler, so that the common logic can
be implemented in icp_reset() only.
While there we can also drop icp_kvm_realize() and icp_kvm_unrealize(). This
causes icp-kvm to be realized in icp_realize(), which sets icp->xics, but
it has no impact.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If EL3 is not implemented (ie only one security state) then the
one and only ICC_BPR1 register behaves like the Non-secure
ICC_BPR1 in an EL3-present configuration. In particular, its
reset value is GIC_MIN_BPR_NS, not GIC_MIN_BPR.
Correct the erroneous reset value; this fixes a problem where
we might hit the assert added in commit a89ff39ee9.
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1496849369-30282-1-git-send-email-peter.maydell@linaro.org
openpic_tmr_read() is incorrectly computing register offset of the
TCCR, TBCR, TVPR, and TDR registers when accessing the open pic timer
registers. Specifically the offset of timer registers for
openpic_tmr_read() is not accounting for the timer frequency reporting
register (TFFR) which is the first register in the "tmr" memory
region.
openpic_tmr_write() *is* correctly computing the offset by adding
0x10f0 to the address prior to computing the register index. This
patch instead subtracts 0x10 in both the read and write routines and
eliminates some other gratuitous differences between the functions.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----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=tEkM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20170601' into staging
migration/next for 20170601
# gpg: Signature made Thu 01 Jun 2017 17:51:04 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20170601:
migration: Move include/migration/block.h into migration/
migration: Export ram.c functions in its own file
migration: Create include for migration snapshots
migration: Export rdma.c functions in its own file
migration: Export tls.c functions in its own file
migration: Export socket.c functions in its own file
migration: Export fd.c functions in its own file
migration: Export exec.c functions in its own file
migration: Split qemu-file.h
migration: Remove unneeded includes of migration/vmstate.h
migration: shut src return path unconditionally
migration: fix leak of src file on dst
migration: Remove section_id parameter from vmstate_load
migration: loadvm handlers are not used
migration: Use savevm_handlers instead of loadvm copy
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M series MPU is almost the same as the already implemented R
profile MPU (v7 PMSA). So all we need to implement here is the MPU
register interface in the system register space.
This implementation has the same restriction as the R profile MPU
that it doesn't permit regions to be sized down smaller than 1K.
We also do not yet implement support for MPU_CTRL.HFNMIENA; this
bit should if zero disable use of the MPU when running HardFault,
NMI or with FAULTMASK set to 1 (ie at an execution priority of
less than zero) -- if the MPU is enabled we don't treat these
cases any differently.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Message-id: 1493122030-32191-13-git-send-email-peter.maydell@linaro.org
[PMM: Keep all the bits in mpu_ctrl field, rather than
using SCTLR bits for them; drop broken HFNMIENA support;
various cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we calculate the mask to use to get the group priority from
an interrupt priority, the way that NS BPR1 is handled differs
from how BPR0 and S BPR1 work -- a BPR1 value of 1 means
the group priority is in bits [7:1], whereas for BPR0 and S BPR1
this is indicated by a 0 BPR value.
Subtract 1 from the BPR value before creating the mask if
we're using the NS BPR value, for both hardware and virtual
interrupts, as the GICv3 pseudocode does, and fix the comments
accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-4-git-send-email-peter.maydell@linaro.org
icc_bpr_write() was not enforcing that writing a value below the
minimum for the BPR should behave as if the BPR was set to the
minimum value. This doesn't make a difference for the secure
BPRs (since we define the minimum for the QEMU implementation
as zero) but did mean we were allowing the NS BPR1 to be set to
0 when 1 should be the lowest value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-3-git-send-email-peter.maydell@linaro.org
We were setting the VBPR1 field of VMCR_EL2 to icv_min_vbpr()
on reset, but this is not correct. The field should reset to
the minimum value of ICV_BPR0_EL1 plus one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-2-git-send-email-peter.maydell@linaro.org
Split the file into public and internal interfaces. I have to rename
the external one because we can't have two include files with the same
name in the same directory. Build system gets confused. The only
exported functions are the ones that handle basic types.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Now that ICPState objects get finalized on CPU unplug, we should unregister
reset handlers as well to avoid a QEMU crash at machine reset time.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit a45863bda9 ("xics_kvm: Don't enable KVM_CAP_IRQ_XICS if
already enabled"), we were able to re-hotplug a vCPU that had been hot-
unplugged ealier, thanks to a boolean flag in ICPState that we set when
enabling KVM_CAP_IRQ_XICS.
This could work because the lifecycle of all ICPState objects was the
same as the machine. Commit 5bc8d26de2 ("spapr: allocate the ICPState
object from under sPAPRCPUCore") broke this assumption and now we always
pass a freshly allocated ICPState object (ie, with the flag unset) to
icp_kvm_cpu_setup().
This cause re-hotplug to fail with:
Unable to connect CPU8 to kernel XICS: Device or resource busy
Let's fix this by caching all the vCPU ids for which KVM_CAP_IRQ_XICS was
enabled. This also drops the now useless boolean flag from ICPState.
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function only does hypercall and RTAS-call registration, and thus
never returns an error. This patch adapt the prototype to reflect that.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
An ioapic device is already created by the q35 initialization
code, and using "-device ioapic" or "-device kvm-ioapic" will
always fail with "Only 1 ioapics allowed". Remove the
user_creatable flag from the ioapic device classes.
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
commit 33cd52b5d7 unset
cannot_instantiate_with_device_add_yet in TYPE_SYSBUS, making all
sysbus devices appear on "-device help" and lack the "no-user"
flag in "info qdm".
To fix this, we can set user_creatable=false by default on
TYPE_SYS_BUS_DEVICE, but this requires setting
user_creatable=true explicitly on the sysbus devices that
actually work with -device.
Fortunately today we have just a few has_dynamic_sysbus=1
machines: virt, pc-q35-*, ppce500, and spapr.
virt, ppce500, and spapr have extra checks to ensure just a few
device types can be instantiated:
* virt supports only TYPE_VFIO_CALXEDA_XGMAC, TYPE_VFIO_AMD_XGBE.
* ppce500 supports only TYPE_ETSEC_COMMON.
* spapr supports only TYPE_SPAPR_PCI_HOST_BRIDGE.
This patch sets user_creatable=true explicitly on those 4 device
classes.
Now, the more complex cases:
pc-q35-*: q35 has no sysbus device whitelist yet (which is a
separate bug). We are in the process of fixing it and building a
sysbus whitelist on q35, but in the meantime we can fix the
"-device help" and "info qdm" bugs mentioned above. Also, despite
not being strictly necessary for fixing the q35 bug, reducing the
list of user_creatable=true devices will help us be more
confident when building the q35 whitelist.
xen: We also have a hack at xen_set_dynamic_sysbus(), that sets
has_dynamic_sysbus=true at runtime when using the Xen
accelerator. This hack is only used to allow xen-backend devices
to be dynamically plugged/unplugged.
This means today we can use -device with the following 22 device
types, that are the ones compiled into the qemu-system-x86_64 and
qemu-system-i386 binaries:
* allwinner-ahci
* amd-iommu
* cfi.pflash01
* esp
* fw_cfg_io
* fw_cfg_mem
* generic-sdhci
* hpet
* intel-iommu
* ioapic
* isabus-bridge
* kvmclock
* kvm-ioapic
* kvmvapic
* SUNW,fdtwo
* sysbus-ahci
* sysbus-fdc
* sysbus-ohci
* unimplemented-device
* virtio-mmio
* xen-backend
* xen-sysdev
This patch adds user_creatable=true explicitly to those devices,
temporarily, just to keep 100% compatibility with existing
behavior of q35. Subsequent patches will remove
user_creatable=true from the devices that are really not meant to
user-creatable on any machine, and remove the FIXME comment from
the ones that are really supposed to be user-creatable. This is
being done in separate patches because we still don't have an
obvious list of devices that will be whitelisted by q35, and I
would like to get each device reviewed individually.
Cc: Alexander Graf <agraf@suse.de>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-block@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: sstabellini@kernel.org
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-3-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[ehabkost: Small changes at sysbus_device_class_init() comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This allows us to remove lots of includes of migration/migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Kernel commit 17d48610ae0f ("KVM: PPC: Book 3S: XICS: Implement ICS
P/Q states") added new bits to the state used by KVM IRQs. Currently,
QEMU does not preserve these bits, so migrating (or otherwise saving
and restoring) the guest state causes the P and Q bits to be cleared.
Clearing the P bit has no effect, because the kernel will set it based
on other data, but the loss of a set Q bit will cause a lost
interrupt.
This patch preserves the P and Q bits, correcting the problem.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ics_get_kvm_state() "or"s set bits into irq->status but does not mask
out clear bits.
Correct this by initializing the IRQ status to zero before adding bits
to it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This provides a new ICPState object for the PowerNV machine (POWER8).
Access to the Interrupt Management area is done though a memory
region. It contains the registers of the Interrupt Control Presenters
of each thread which are used to accept, return, forward interrupts in
the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will be used by derived classes in PowerNV for customization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, all the ICPs are created before the CPUs, stored in an array
under the sPAPR machine and linked to the CPU when the core threads
are realized. This modeling brings some complexity when a lookup in
the array is required and it can be simplified by allocating the ICPs
when the CPUs are.
This is the purpose of this proposal which introduces a new 'icp_type'
field under the machine and creates the ICP objects of the right type
(KVM or not) before the PowerPCCPU object are.
This change allows more cleanups : the removal of the icps array under
the sPAPR machine and the removal of the xics_get_cpu_index_by_dt_id()
helper.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the second step to abstract the IRQ 'server' number of the
XICS layer. Now that the prereq cleanups have been done in the
previous patch, we can move down the 'cpu_dt_id' to 'cpu_index'
mapping in the sPAPR machine handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICPState array of the sPAPR machine is indexed with
'cpu_index' of the CPUState. This numbering of CPUs is internal to
QEMU and the guest only knows about what is exposed in the device
tree, that is the 'cpu_dt_id'. This is why sPAPR uses the helper
xics_get_cpu_index_by_dt_id() to do the mapping in a couple of places.
To provide a more generic XICS layer, we need to abstract the IRQ
'server' number and remove any assumption made on its nature. It
should not be used as a 'cpu_index' for lookups like xics_cpu_setup()
and xics_cpu_destroy() do.
To reach that goal, we choose to introduce a generic 'intc' backlink
under PowerPCCPU, and let the machine core init routine do the
ICPState lookup. The resulting object is passed on to xics_cpu_setup()
which does the store under PowerPCCPU. The IRQ 'server' number in XICS
is now generic. sPAPR uses 'cpu_dt_id' and PowerNV will use 'PIR'
number.
This also has the benefit of simplifying the sPAPR hcall routines
which do not need to do any ICPState lookups anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
s390_get_flic() is called many times to obtain the flic. This wastes a
lot of time as it calls object_resolve_path() every time. Let's cache
S390FLICState by defining it as static.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS needs to be checked before
attempting to read ICC_CTLR_EL1; otherwise kernel versions not
exposing this kvm device group will be incompatible with qemu 2.9.
Fixes: 07a5628 ("hw/intc/arm_gicv3_kvm: Reset GICv3 cpu interface registers")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Prakash B <bjsprakash.linux@gmail.com>
Tested-by: Alexander Graf <agraf@suse.de>
Message-id: 1490721640-13052-1-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 07bfa35477.
The global variable is only read as part of a
apic_reset_irq_delivered();
qemu_irq_raise(s->irq);
if (!apic_get_irq_delivered()) {
sequence, so the value never matters at migration time.
Reported-by: Dr. David Alan Gilbert <dglibert@redhat.com>
Cc: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a const qom link between the CPU and the IIC instead
of passing the CPU link through a qom property.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20170317210627.23532-1-marex@denx.de
Cc: Alexander Graf <agraf@suse.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While I was debugging the icount issues I realised a bunch of the
messages look quite similar. I've fixed this by including __func__ in
the debug print. At the same time I move the a modern if (GATE) style
printf which ensures the compiler can check for format string errors
even if the code gets optimised away in the non-DEBUG_GIC case.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The recent changes on the XICS layer removed the XICSState object to
let the sPAPR machine handle the ICP and ICS directly. The reset of
these objects was previously handled by XICSState, which was a SysBus
device, and to keep the same behavior, the ICP and ICS were assigned
to SysbBus.
But that broke the 'info qtree' command in the monitor. 'qtree'
performs a loop on the children of a bus to print their properties and
SysBus devices are expected to be found under SysBus, which is not the
case anymore.
The fix for this problem is to register reset handlers for the ICP and
ICS objects and stop using SysBus for such devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gI0E
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170301' into staging
ppc patch queue for 2017-03-01
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
# gpg: Signature made Wed 01 Mar 2017 04:43:06 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170301: (50 commits)
Add PowerPC 32-bit guest memory dump support
ppc/xics: rename 'ICPState *' variables to 'icp'
ppc/xics: move InterruptStatsProvider to the sPAPR machine
ppc/xics: move ics-simple post_load under the machine
ppc/xics: remove the XICSState classes
ppc/xics: export the XICS init routines
ppc/xics: move the ICP array under the sPAPR machine
ppc/xics: register the reset handler of ICP objects
ppc/xics: simplify spapr_dt_xics() interface
ppc/xics: use the QOM interface to grab an ICP
ppc/xics: move the cpu_setup() handler under the ICPState class
ppc/xics: simplify the cpu_setup() handler
ppc/xics: move kernel_xics_fd out of KVMXICSState
ppc/xics: extend the QOM interface to handle ICPs
ppc/xics: remove the XICS list of ICS
ppc/xics: register the reset handler of ICS objects
ppc/xics: remove xics_find_source()
ppc/xics: use the QOM interface to resend irqs
ppc/xics: use the QOM interface to get irqs
ppc/xics: use the QOM interface under the sPAPR machine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'ICPState *' variables are currently named 'ss'. This is confusing, so
let's give them an appropriate name: 'icp'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It provides a better monitor output of the ICP and ICS objects, else
the objects are printed out of order.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object uses a post_load() handler which is implicitly relying
on the fact that the internal state of the ICS and ICP objects has
been restored but this is not guaranteed. So, let's move the code
under the post_load() handler of the machine where we know the objects
have been fully restored.
The icp_resend() handler of the XICSFabric QOM interface is also
removed as it is now obsolete.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICSState classes are not used anymore. They have now been fully
deprecated by the XICSFabric QOM interface. Do the cleanups.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is nothing left related to the XICS object in the realize
functions of the KVMXICSState and XICSState class. So adapt the
interfaces to call these routines directly from the sPAPR machine init
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The reset of the ICP objects is currently handled by XICS but this can
be done for each individual ICP.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_dt_xics() only needs the number of servers to build the device
tree nodes. Let's change the routine interface to reflect that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also introduce a xics_icp_get() helper to simplify the changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler is currently under the XICSState class but it
really belongs under ICPState as it is setting up an individual vCPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler currently takes a 'XICSState *' argument to
grab the kernel ICP file descriptor. This interface can be simplified
by using the 'xics' backlink of the ICP object.
This change is also required by subsequent patches which makes use of
the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The kernel ICP file descriptor is the only reason behind the
KVMXICSState class and it's in the way of more cleanups. Let's make it
a static for the moment and move forward.
If this is problem, we could use an attribute under the sPAPR machine
later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's add two new handlers for ICPs. One is to get an ICP object from
a server number and a second is to resend the irqs when needed.
The icp_resend() handler is a temporary workaround needed by the
ics-simple post_load() handler. It will be removed when the post_load
portion can be done at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is not used anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The reset of the ICS objects is currently handled by XICS but this can
be done for each individual ICS. This also reduces the use of the XICS
list of ICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is not used anymore now that we have the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the ICPState 'xics' backlink to be a XICSFabric, this
removes the need of using qdev_get_machine() to get the QOM interface
in some of the routines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 'ics_get' and 'ics_resend' handlers to the sPAPR machine. These
are relatively simple for a single ICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This interface provides two simple handlers. One is to get an ICS
(Interrupt Source Controller) object from an irq number and a second
to resend the irqs when needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is, again, to reduce the use of the list of ICS objects. Let's
make each individual ICS and ICP object an InterruptStatsProvider and
remove this same interface from XICSState.
The InterruptStatsProvider will be moved at the machine level after
the XICS cleanups are completed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A list of ICS objects was introduced under the XICS object for the
PowerNV machine but, for the sPAPR machine, it brings extra complexity
as there is only a single ICS. To simplify the code, let's add the ICS
pointer under the sPAPR machine and try to reduce the use of this list
where possible.
Also, change the xics_spapr_*() routines to use an ICS object instead
of an XICSState and change their name to reflect that these are
specific to the sPAPR ICS object.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICP (Interrupt Controller Presenter) objects are created by
the 'nr_servers' property handler of the XICS object and a class
handler. They are realized in the XICS object realize routine.
Let's simplify the process by creating the ICP objects along with the
XICS object at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICS (Interrupt Controller Source) object is created and
realized by the init and realize routines of the XICS object, but some
of the parameters are only known at the machine level.
These parameters are passed from the sPAPR machine to the ICS object
in a rather convoluted way using property handlers and a class handler
of the XICS object. The number of irqs required to allocate the IRQ
state objects in the ICS realize routine is one of them.
Let's simplify the process by creating the ICS object along with the
XICS object at the machine level and link the ICS into the XICS list
of ICSs at this level also. In the sPAPR machine, there is only a
single ICS but that will change with the PowerNV machine.
Also, QOMify the creation of the objects and get rid of the
superfluous code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently xics - the component of the IBM POWER interrupt controller
representing the overall interrupt fabric / architecture is
represented as a descendent of SysBusDevice. However, this is not
really correct - the xics presents nothing in MMIO space so it should
be an "unattached" device in the current QOM model.
Since this device will always be created by the machine type, not created
specifically from the command line, and because it has no migrated state
it should be safe to move it around the device composition tree.
Therefore this patch changes it to a descendent of TYPE_DEVICE, and
makes it an unattached device. So that its reset handler still gets
called correctly, we add a qdev_set_parent_bus() to attach it to
sysbus. It's not really clear that's correct (instead of using
register_reset()) but it appears to a common technique.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[clg corrected problems with reset]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg folded together and updated commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reset CPU interface registers of GICv3 when CPU is reset.
For this, ARMCPRegInfo struct is registered with one ICC
register whose resetfn is called when cpu is reset.
All the ICC registers are reset under one single register
reset function instead of calling resetfn for each ICC
register.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487850673-26455-6-git-send-email-vijay.kilari@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add gicv3state void pointer to CPUARMState struct
to store GICv3CPUState.
In case of usecase like CPU reset, we need to reset
GICv3CPUState of the CPU. In such scenario, this pointer
becomes handy.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487850673-26455-5-git-send-email-vijay.kilari@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This actually implements pre_save and post_load methods for in-kernel
vGICv3.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Message-id: 1487850673-26455-4-git-send-email-vijay.kilari@gmail.com
[PMM:
* use decimal, not 0bnnn
* fixed typo in names of ICC_APR0R_EL1 and ICC_AP1R_EL1
* completely rearranged the get and put functions to read and write
the state in a natural order, rather than mixing distributor and
redistributor state together]
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
[Vijay:
* Update macro KVM_VGIC_ATTR
* Use 32 bit access for gicd and gicr
* GICD_IROUTER, GICD_TYPER, GICR_PROPBASER and GICR_PENDBASER reg
access are changed from 64-bit to 32-bit access
* Add ICC_SRE_EL1 save and restore
* Dropped translate_fn mechanism and coded functions to handle
save and restore of edge_trigger and priority
* Number of APnR register saved/restored based on number of
priority bits supported]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
To Save and Restore ICC_SRE_EL1 register introduce vmstate
subsection and load only if non-zero.
Also initialize icc_sre_el1 with to 0x7 in pre_load
function.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487850673-26455-3-git-send-email-vijay.kilari@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The NVIC is a core v7M device that exists for all v7M CPUs;
put it under a CONFIG_ARM_V7M rather than hiding it under
CONFIG_STELLARIS.
(We'll use CONFIG_ARM_V7M for the SysTick device too
when we split it out of the NVIC.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-9-git-send-email-peter.maydell@linaro.org
Make the NVIC device expose a memory region for its users
to map, rather than mapping itself into the system memory
space on realize, and get the one user (the ARMv7M object)
to do this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-7-git-send-email-peter.maydell@linaro.org
Move the NVICState struct definition into a header, so we can
embed it into other QOM objects like SoCs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-3-git-send-email-peter.maydell@linaro.org
Implement the NVIC SHCSR write behaviour which allows pending and
active status of some exceptions to be changed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Implement the exception return consistency checks
described in the v7M pseudocode ExceptionReturn().
Inspired by a patch from Michael Davidsaver's series, but
this is a reimplementation from scratch based on the
ARM ARM pseudocode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The VECTCLRACTIVE and VECTRESET bits in the AIRCR are both
documented as UNPREDICTABLE if you write a 1 to them when
the processor is not halted in Debug state (ie stopped
and under the control of an external JTAG debugger).
Since we don't implement Debug state or emulated JTAG
these bits are always UNPREDICTABLE for us. Instead of
logging them as unimplemented we can simply log writes
as guest errors and ignore them.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: change extracted from another patch; commit message
constructed from scratch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Having armv7m_nvic_acknowledge_irq() return the new value of
env->v7m.exception and its one caller assign the return value
back to env->v7m.exception is pointless. Just make the return
type void instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The v7M exception architecture requires that if a synchronous
exception cannot be taken immediately (because it is disabled
or at too low a priority) then it should be escalated to
HardFault (and the HardFault exception is then taken).
Implement this escalation logic.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: extracted from another patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Now that the NVIC is its own separate implementation, we can
clean up the GIC code by removing REV_NVIC and conditionals
which use it.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The M profile condition for when we can take a pending exception or
interrupt is not the same as that for A/R profile. The code
originally copied from the A/R profile version of the
cpu_exec_interrupt function only worked by chance for the
very simple case of exceptions being masked by PRIMASK.
Replace it with a call to a function in the NVIC code that
correctly compares the priority of the pending exception
against the current execution priority of the CPU.
[Michael Davidsaver's patchset had a patch to do something
similar but the implementation ended up being a rewrite.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Despite some superficial similarities of register layout, the
M-profile NVIC is really very different from the A-profile GIC.
Our current attempt to reuse the GIC code means that we have
significant bugs in our NVIC.
Implement the NVIC as an entirely separate device, to give
us somewhere we can get the behaviour correct.
This initial commit does not attempt to implement exception
priority escalation, since the GIC-based code didn't either.
It does fix a few bugs in passing:
* ICSR.RETTOBASE polarity was wrong and didn't account for
internal exceptions
* ICSR.VECTPENDING was 16 too high if the pending exception
was for an external interrupt
* UsageFault, BusFault and MemFault were not disabled on reset
as they are supposed to be
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
[PMM: reworked, various bugs and stylistic cleanups]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Add a state field for the v7M PRIGROUP register and implent
reading and writing it. The current NVIC doesn't honour
the values written, but the new version will.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Rename the nvic_state struct to NVICState, to match
our naming conventions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
This finally allows TCG to benefit from the iothread introduction: Drop
the global mutex while running pure TCG CPU code. Reacquire the lock
when entering MMIO or PIO emulation, or when leaving the TCG loop.
We have to revert a few optimization for the current TCG threading
model, namely kicking the TCG thread in qemu_mutex_lock_iothread and not
kicking it in qemu_cpu_kick. We also need to disable RAM block
reordering until we have a more efficient locking mechanism at hand.
Still, a Linux x86 UP guest and my Musicpal ARM model boot fine here.
These numbers demonstrate where we gain something:
20338 jan 20 0 331m 75m 6904 R 99 0.9 0:50.95 qemu-system-arm
20337 jan 20 0 331m 75m 6904 S 20 0.9 0:26.50 qemu-system-arm
The guest CPU was fully loaded, but the iothread could still run mostly
independent on a second core. Without the patch we don't get beyond
32206 jan 20 0 330m 73m 7036 R 82 0.9 1:06.00 qemu-system-arm
32204 jan 20 0 330m 73m 7036 S 21 0.9 0:17.03 qemu-system-arm
We don't benefit significantly, though, when the guest is not fully
loading a host CPU.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <1439220437-23957-10-git-send-email-fred.konrad@greensocs.com>
[FK: Rebase, fix qemu_devices_reset deadlock, rm address_space_* mutex]
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
[EGC: fixed iothread lock for cpu-exec IRQ handling]
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: -smp single-threaded fix, clean commit msg, BQL fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
[PM: target-arm changes]
Acked-by: Peter Maydell <peter.maydell@linaro.org>
To make virtio-ccw supports more that 64 virtqueues we will have to
increase ADAPTER_ROUTES_MAX_GSI which is currently limiting the number if
possible adapter routes. Of course increasing the number of supported
routes can break backwards migration.
Let us introduce a compatibility property adapter_routes_max_batch so
client code can use the some old limit if in compatibility mode and
retain the migration compatibility.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Current code puts a 'FLIC_FAILED' marker into the migration stream
to indicate something went wrong while saving flic state and fails
load if it encounters that marker. VMState's put routine recently
gained the ability to return error codes (but did not wire it up
yet).
In order to be able to reap the benefits of returning an error and
failing migration on the source already once this gets wired up
in core, return an error in addition to storing 'FLIC_FAILED'.
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
If the GIC interrupt mask is changed by a write to the smask (set mask)
or rmask (reset mask) registers, we need to re-evaluate the state of the
pins/IRQs fed to the CPU. Without doing so we risk leaving a pin high
despite the interrupt that led to that state being masked, or losing
interrupts if an already pending interrupt is unmasked.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
This patch adds call to apic_reset_irq_delivered when the virtual
machine is reset.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170131114054.276.62201.stgit@PASHA-ISP>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It should be 0x20, rather than 0x11.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1486106298-3699-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
I'll be adding an error to it in a subsequent patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch implements saving/restoring of static apic_delivered variable.
v8: saving static variable only for one of the APICs
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170126123429.5412.94368.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix a broken expression in the calculation of ELRSR
register bits: instead of "(lr & ICH_LR_EL2_HW) == 1"
we want to check for != 0, because the HW bit is not
bit 0 so a test for == 1 is always false.
Fixes: https://bugs.launchpad.net/bugs/1658506
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1485255993-6322-1-git-send-email-peter.maydell@linaro.org
The CCR.USERSETMPEND bit has to be set to permit unprivileged code to
write to the Software Triggered Interrupt register; honour this bit
rather than letting any code write to the register.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-9-git-send-email-peter.maydell@linaro.org
[PMM: Tweak commit message, comment, phrasing of condition]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the v7M system registers CCR, CFSR, HFSR, DFSR, BFAR and
MMFAR. For the moment these simply read as written (with some basic
handling of RAZ/WI bits and W1C semantics).
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-5-git-send-email-peter.maydell@linaro.org
[PMM: drop warning about setting unimplemented CCR bits;
tweak commit message; add DFSR]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many NVIC operations access the CPU state, so store a pointer in
struct nvic_state rather than fetching it via qemu_get_cpu() every
time we need it.
As with the arm_gicv3_common code, we currently just call
qemu_get_cpu() in the NVIC's realize method, but in future we might
want to use a QOM property to pass the CPU to the NVIC.
This imposes an ordering requirement that the CPU is
realized before the NVIC, but that is always true since
both are dealt with in armv7m_init().
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-3-git-send-email-peter.maydell@linaro.org
[PMM: Use qemu_get_cpu(0) rather than first_cpu; expand
commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2c21ee7 ("migration: extend VMStateInfo") missed a void -> int
return conversion for kvm_flic_save().
Fixes: 2c21ee7 ("migration: extend VMStateInfo")
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add the Altera Nios2 internal interrupt controller model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-5-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fzmu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170120-v2' into staging
First set of s390x patches for 2.9:
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
# gpg: Signature made Fri 20 Jan 2017 09:11:58 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170120-v2:
virtio-ccw: fix ring sizing
s390x/pci: merge msix init functions
s390x/pci: handle PCIBridge bus number
s390x/pci: use hashtable to look up zpci via fh
s390x/pci: PCI multibus bridge handling
s390x/pci: optimize calling s390_get_phb()
s390x/pci: change the device array to a list
s390x/pci: dynamically allocate iommu
s390x/pci: make S390PCIIOMMU inherit Object
s390x/kvm: use kvm_gsi_routing_enabled in flic
s390x: add compat machine for 2.9
s390x: remove double compat statement
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the architecturally required traps from NS EL1
to EL2 for the CPU interface registers. These fall into
several different groups:
* group-0-only registers all trap if ICH_HRC_EL2.TALL0 is set
(exactly the registers covered by gicv3_fiq_access())
* group-1-only registers all trap if ICH_HRC_EL2.TALL1 is set
(exactly the registers covered by gicv3_irq_access())
* DIR traps if ICH_HCR_EL2.TC or ICH_HCR_EL2.TDIR are set
* PMR, RPR, CTLR trap if ICH_HCR_EL2.TC is set
* SGI0R, SGI1R, ASGI1R trap if ICH_HCR_EL2.TC is set or
if HCR_EL2.IMO or HCR_EL2.FMO are set
We split DIR and the SGI registers out into their own access
functions, leaving the existing gicv3_irqfiq_access() just
handling PMR, RPR and CTLR.
This commit doesn't implement support for trapping on
HSTR_EL2.T12 for the 32-bit registers, as we don't implement
any of those per-coprocessor trap bits currently and
probably will want to do those in some more centralized way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-14-git-send-email-peter.maydell@linaro.org
Implement the function which signals virtual interrupts to the
CPU as appropriate following CPU interface state changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-13-git-send-email-peter.maydell@linaro.org
If the HCR_EL2.IMO or FMO bits are set, accesses to ICC_
system registers are redirected to be accesses to ICV_
registers (the guest-visible interface to the virtual
interrupt controller). Implement this behaviour for the
ICV_ registers which are simple accessors to the underlying
register state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-10-git-send-email-peter.maydell@linaro.org
The GICv3 virtualization interface includes system registers
accessible only to the hypervisor which form the control
interface for interrupt virtualization. Implement these
registers.
The function gicv3_cpuif_virt_update() which determines
whether it needs to signal vIRQ, vFIQ or a maintenance
interrupt is introduced here as a stub function -- its
implementation will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-9-git-send-email-peter.maydell@linaro.org
As the first step in adding support for the virtualization
extensions to the GICv3 emulation:
* add the necessary data fields to the state structures
* add the fields to the migration state, as a subsection
which is only present if virtualization is enabled
The use of a subsection means we retain migration
compatibility as EL2 is not enabled on any CPUs currently.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-8-git-send-email-peter.maydell@linaro.org
Add defines to gicv3_internal.h for fields in the ICH_*
system registers which form the GIC virtualization control
interface.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-7-git-send-email-peter.maydell@linaro.org
Augment the GIC's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
We never use these, but it's helpful to keep the v2-and-earlier
GIC's external interface in line with that of the GICv3 to
avoid board code having to add extra code conditional on which
version of the GIC is in use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-3-git-send-email-peter.maydell@linaro.org
Augment the GICv3's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-2-git-send-email-peter.maydell@linaro.org
Let's use kvm_gsi_routing_enabled() to check if kvm supports
KVM_CAP_IRQ_ROUTING in order to avoid a needless ioctl invocation.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Use the Intel HAX is kernel-based hardware acceleration module for
Windows (similar to KVM on Linux).
Based on the "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <7b9cae28a0c379ab459c7a8545c9a39762bd394f.1484045952.git.vpalatin@chromium.org>
[Drop hax_populate_ram stub. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split irqchip works based on the fact that we kept the first 24 gsi
routing entries inside KVM for userspace ioapic's use. When system
boot, we'll reserve these MSI routing entries before hand. However,
after migration, we forgot to re-configure it up in the destination
side. The result is, we'll get invalid gsi routing entries after
migration (all empty), and we get interrupts with vector=0, then
strange things happen, like keyboard hang.
The solution is simple - we update them after migration, which is a
one line fix.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-4-git-send-email-peterx@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From time to time, there are issues with ioapic, either on guest side or
on hypervisor side. Good to have some persistent traces for better
triaging and debugging.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv3 requires that we only signal Pending interrupts to
the CPU. This category does not include Pending+Active interrupts,
which means we need to check whether the interrupt is Active in
the gicr_int_pending() and gicd_int_pending() functions.
Interrupts are rarely in the Active+Pending state, but KVM
uses this as part of its handling of the virtual timer, so
this bug was causing KVM to go into an infinite loop of
taking the vtimer interrupt when the guest first triggered it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In the ARMCPRegInfo definitions for the GICv3 CPU interface
registers, we were trying to use .fieldoffset to specify
the locations of data fields within the GICv3CPUState struct.
This is completely broken, because .fieldoffset is for offsets
into the CPUARMState struct. We didn't notice because we
were only using this for reads to BPR0, AP0R<n>, IGRPEN0
and CTLR_EL3, and Linux doesn't use these registers.
Replace the .fieldoffset uses with explicit read functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20161209143703.29457-1-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
According to ARM DUI 0552A 4.2.10. NVIC set pending status
also for disabled interrupts. Correct the logic for
when interrupts are marked pending both on input level
transition and when interrupts are dismissed, to match
the NVIC behaviour rather than the 11MPCore GIC.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the device tree node for the XICS interrupt controller is in
spapr_create_fdt_skel(). As part of consolidating device tree construction
to reset time, this moves it to a function called from spapr_build_fdt().
In addition we move the actual code into hw/intc/xics_spapr.c with the
rest of the PAPR specific interrupt controller code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Useful to debug interrupt problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- added a test on ->irqs as it is not necessarily allocated
(PHB3_MSI)
- removed static variable g_xics and replace with a loop on all
children to find the xics objects.
- rebased on InterruptStatsProvider interface ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SDM: x2APIC State Transitions:
State Changes From xAPIC Mode to x2APIC Mode
"
Any APIC ID value written to the memory-mapped
local APIC ID register is not preserved
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
APIC ID should be restored to initial APIC ID
state after Reset and Power-On.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fix some problems with the tracepoints for ICC register reads
and writes:
* tracepoints for ICC_BPR<n>, ICC_AP<n>R<x>, ICC_IGRPEN<n>,
ICC_EIOR<n> were not printing the <n> that indicated whether
the access was to the group 0 or 1 register
* the ICC_IGREPEN1_EL3 read function was not actually calling
the associated tracepoint
* the ICC_BPR<n> write function was incorrectly calling the
tracepoint for ICC_PMR writes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1476294876-12340-4-git-send-email-peter.maydell@linaro.org
Remove unused debugging code to fix native building on aarch64. Without
this change, the following -Werr output inhibits make from completing.
qemu/hw/intc/arm_gic_kvm.c:38:18: error: debug_gic_kvm defined but not used [-Werror=unused-const-variable=]
static const int debug_gic_kvm = 0;
^~~~~~~~~~~~~
cc1: all warnings being treated as errors
qemu/rules.mak:60: recipe for target 'hw/intc/arm_gic_kvm.o' failed
make[1]: *** [hw/intc/arm_gic_kvm.o] Error 1
Makefile:205: recipe for target 'subdir-aarch64-softmmu' failed
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20161011163202.19720-1-cov@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MMIO based interface to APIC doesn't work well with MSIs that have
upper address bits set (remapped x2APIC MSIs). A specialized interface
is a quick and dirty way to avoid the shortcoming.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every configuration has only up to one APIC class and we'll be extending
the class with a function that can be called without an instanced
object, so a direct access to the class is convenient.
This patch will break compilation if some code uses apic_get_class()
with CONFIG_USER_ONLY.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing implementation remains same and ics-base is introduced. The
type name "ics" is retained, and all the related functions renamed as
ics_simple_*
This will allow different implementations for the source controllers
such as the MSI support of PHB3 on Power8 which uses in-memory state
tables for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: added ICS_BASE_GET_CLASS and related fixes, based on :
http://patchwork.ozlabs.org/patch/646010/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of an array of fixed sized blocks, use a list, as we will need
to have sources with variable number of interrupts. SPAPR only uses
a single entry. Native will create more. If performance becomes an
issue we can add some hashed lookup but for now this will do fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ move the initialization of list to xics_common_initfn,
restore xirr_owner after migration and move restoring to
icp_post_load]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ clg: removed the icp_post_load() changes from nikunj patchset v3:
http://patchwork.ozlabs.org/patch/646008/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS control frame is in-kernel emulated while accesses to the
GITS_TRANSLATER are mediated through the KVM_SIGNAL_MSI ioctl (MSI
direct MSI injection advertised by the CAP_SIGNAL_MSI capability)
the kvm_gsi_direct_mapping is explicitly set to false to emphasize the
difference with GICv2M. Direct mapping cannot work with ITS since
the content of the MSI data is not the target interrupt ID but an
eventd id.
GSI routing is advertised (kvm_gsi_routing_allowed) as well as
msi/irqfd signaling (kvm_msi_via_irqfd_allowed).
The MSI frame (GITS_TRANSLATER) absolute GPA is computed on first
kvm_its_send_msi() call. It is then passed through KVM_SIGNAL_MSI
ioctl.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-6-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the basic skeleton for both KVM and software-emulated ITS.
Since we already prepare status structure, we also introduce complete
VMState description. But, because we currently have no migratable
implementations, we also set unmigratable flag.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Advertise gsi routing and set up irqchip routing entries for
GIC SPIs.
This is not mandated as long as MSI routing is not used
(because the kernel sets a default irqchip routing table).
However once MSI routing gets used (for VIRTIO-PCI vhost for
example), the first call to KVM_SET_GSI_ROUTING overrides the
kernel default irqchip table.
If no routing entry exists for the GSI, any IRQFD signaling for
this GSI will fail.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have to change the vmstate version due to changes in statistics counters.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-5-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This interface will be used by HMP commands 'info irq' and 'info pic'.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-2-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's 2.8 now, and maybe it's time to switch IOAPIC default version to
0x20.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474608795-23058-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix inconsistent irq status, because of this in the trace logs, for e.g.
LSI status was 0x7, i.e. XICS_STATUS_ASSERTED, XICS_STATUS_SENT and
XICS_STATUS_REJECTED all set, which did not make sense. So the REJECTED
would have been set in earlier interrupt cycle, and then asserted and
sent in this current one.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new APIC macro to replace APIC_COMMON macro in
hw/intc/apic.c in order to capture access LAPIC in qemu
even if LAPIC is emulated in kvm.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Message-Id: <1473923759-13912-1-git-send-email-wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We abort a few lines above if kernel_xics_fd == -1.
This is only code cleanup.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some old Linux kernels (upstream before v4.0), or any released RHEL
kernels has problem in sending APIC EOI when IR is enabled. Meanwhile,
many of them only support explicit EOI for IOAPIC, which is only
introduced in IOAPIC version 0x20. This patch provide a way to boost
QEMU IOAPIC to version 0x20, in order for QEMU to correctly receive EOI
messages.
Without boosting IOAPIC version to 0x20, kernels before commit d32932d
("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
will have trouble enabling both IR and level-triggered interrupt devices
(like e1000).
To upgrade IOAPIC to version 0x20, we need to specify:
-global ioapic.version=0x20
To be compatible with old systems, 0x11 will still be the default IOAPIC
version. Here 0x11 and 0x20 are the only versions to be supported.
One thing to mention: this patch only applies to emulated IOAPIC. It
does not affect kernel IOAPIC behavior.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1470059959-372-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For level triggered interrupts, we will get Remote IRR bit cleared after
guest kernel finished processing specific request. Before that, we
should ignore the same interrupt from triggering again.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1469974685-4144-1-git-send-email-peterx@redhat.com>
[Push new "if" up so that it covers KVM split irqchip as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let IOAPIC the first consumer of x86 IOMMU IEC invalidation
notifiers. This is only used for split irqchip case, when vIOMMU
receives IR invalidation requests, IOAPIC will be notified to update
kernel irq routes. For simplicity, we just update all IOAPIC routes,
even if the invalidated entries are not IOAPIC ones.
Since now we are creating IOMMUs using "-device" parameter, IOMMU
device will be created after IOAPIC. We need to do the registration
after machine done by leveraging machine_done notifier.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Abstract IOAPIC entry parsing logic into a helper function.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch translates all IOAPIC interrupts into MSI ones. One pseudo
ioapic address space is added to transfer the MSI message. By default,
it will be system memory address space. When IR is enabled, it will be
IOMMU address space.
Currently, only emulated IOAPIC is supported.
Idea suggested by Jan Kiszka and Rita Sinha in the following patch:
https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
instance_id is generated by last_used_id + 1 for a given device type
so for QEMU with 3 CPUs instance_id for APICs is a seti of [0, 1, 2]
When CPU in the middle is hot-removed and migration started
APICs with instance_ids 0 and 2 are transferred in migration stream.
However target starts with 2 CPUs and APICs' instance_ids are
generated from scratch [0, 1] hence migration fails with error
Unknown savevm section or instance 'apic' 2
Fix issue by manually registering APIC's vmsd with apic_id as
instance_id, in this case instance_id on target will always
match instance_id on source as apic_id is the same for a given
cpu instance.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Callbacks will do necessary cleanups before APIC device is deleted
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
local_apics[] is sized to contain all APIC ID supported in xAPIC mode,
so use APIC ID as index in it instead of constantly increasing counter idx.
Fixes error "apic initialization failed" when a CPU hotplugged and
unplugged more times than there are free slots in local_apics[].
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MAX_APICS is only used by child 'apic' class and not
by its parent TYPE_APIC_COMMON or any other derived
class.
Move check into end user 'apic' class so it won't
get in the way of other APIC implementations
if they support more then MAX_APICS.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Coverity complains that the GICR_IPRIORITYR case in gicv3_readl()
can overflow an array, because it doesn't know that the offsets
passed to that function must be word aligned. Add some assert()s
which hopefully tell Coverity that this isn't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1468261372-17508-1-git-send-email-peter.maydell@linaro.org
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Global Interrupt Controller (GIC) is responsible for mapping each
internal and external interrupt to the correct location for servicing.
The internal representation of registers is different from the specification
in order to consolidate information for each GIC Interrupt Sources and Virtual
Processors with same functionalities. For example SH_MAP00_VP00 registers are
defined like each bit represents a VP but in this implementation the equivalent
map_vp contains VP number in integer form for ease accesses. When it is being
accessed via read write functions an internal data is converted back into the
original format as the specification.
Limitations:
Level triggering only
GIC CounterHi not implemented (Countbits = 32bits)
DINT not implemented
Local WatchDog, Fast Debug Channel, Perf Counter not implemented
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Starting QEMU with -S results in current_cpu containing its initial
value of NULL. It is however possible to connect to such QEMU instance
and query various CPU registers, one example being CPUID, and doing that
results in QEMU segfaulting.
Using qemu_get_cpu(0) seem reasonable enough given that ARMv7M
architecture is a single core architecture.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "ICP" is a different object than the "XICS". For historical reasons,
we have a number of places where we name a variable "icp" while it contains
a XICSState pointer. There *is* an ICPState structure too so this makes
the code really confusing.
This is a mechanical replacement of all those instances to use the name
"xics" instead. There should be no functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[spapr_cpu_init has been moved to spapr_cpu_core.c, change there]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
None of the other presenter functions directly mucks with the
internal state, so don't do it there either.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The common class doesn't change, the KVM one is sPAPR specific. Rename
variables and functions to xics_spapr.
Retain the type name as "xics" to preserve migration for existing sPAPR
guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/intc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-10-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix missing includes of qemu/log.h, which broke compilation with the
simple trace backend (the default backend pulls in log.h implicitly
via trace.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-id: 1466416634-9798-1-git-send-email-peter.maydell@linaro.org
Add the CPU interface registers which deal with acknowledging
and dismissing interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-19-git-send-email-peter.maydell@linaro.org
Implement the registers in the GICv3 CPU interface which generate
new SGI interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-18-git-send-email-peter.maydell@linaro.org
Implement the gicv3_cpuif_update() function which deals with correctly
asserting IRQ and FIQ based on the current running priority of the CPU,
the priority of the highest priority pending interrupt and the CPU's
current exception level and security state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-17-git-send-email-peter.maydell@linaro.org
Implement the CPU interface registers for the GICv3; these are
CPU system registers, not MMIO registers.
This commit implements all the registers which are simple
accessors for GIC state, but not those which act as interfaces
for acknowledging, dismissing or generating interrupts. (Those
will be added in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-16-git-send-email-peter.maydell@linaro.org
Implement the code which updates the GIC state when an interrupt
input into the GIC is asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-15-git-send-email-peter.maydell@linaro.org
Wire up the MMIO functions exposed by the distributor and the
redistributor into MMIO regions exposed by the GICv3 device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-14-git-send-email-peter.maydell@linaro.org
Implement the redistributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-13-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the distributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-12-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new bitmap data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the GICv3 logic to recalculate the highest priority pending
interrupt for each CPU after some part of the GIC state has changed.
We avoid unnecessary full recalculation where possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-11-git-send-email-peter.maydell@linaro.org
This patch includes the device class itself, some ID register
value functions which will be needed by both distributor
and redistributor, and some skeleton functions for handling
interrupts coming in and going out, which will be filled in
in a subsequent patch.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-10-git-send-email-peter.maydell@linaro.org
[PMM: pulled this patch earlier in the sequence, and left
some code out of it for a later patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Add state structure descriptors for the GICv3 state. We mark
the KVM GICv3 device as having a migration blocker until the
code to save and restore the state in the kernel is implemented.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-9-git-send-email-peter.maydell@linaro.org
[PMM: Adjust to renamed struct fields; switched to using uint32_t
array backed bitmaps; add migration blocker setting]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the GICv3 parent_irq and parent_fiq pointers into the
GICv3CPUState structure rather than giving them their own array.
This will make it easy to assert the IRQ and FIQ lines for a
particular CPU interface without having to know or calculate
the CPU index for the GICv3CPUState we are working on.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-8-git-send-email-peter.maydell@linaro.org
Add state information to GICv3 object structure and implement
arm_gicv3_common_reset().
This commit includes accessor functions for the fields which are
stored as bitmaps in uint32_t arrays.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-7-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled:
* Add missing qom/cpu.h include
* Remove legacy-only state fields (we can add them later if/when we add
legacy emulation)
* Use arrays of uint32_t to store the various distributor bitmaps,
and provide accessor functions for the various set/test/etc operations
* Add various missing register offset #defines
* Accessor macros which combine distributor and redistributor behaviour
removed
* Fields in state structures renamed to match architectural register names
* Corrected the reset value for GICR_IENABLER0 since we don't support
legacy mode
* Added ARM_LINUX_BOOT_IF interface for "we are directly booting a kernel in
non-secure" so that we can fake up the firmware-mandated reconfiguration
only when we need it
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
XICS is setup for each CPU during initialization. Provide a routine
to undo the same when CPU is unplugged. While here, move ss->cs management
into xics from xics_kvm since there is nothing KVM specific in it.
Also ensure xics reset doesn't set irq for CPUs that are already unplugged.
This allows reboot of a VM that has undergone CPU hotplug and unplug
to work correctly.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the platform specification, under certain conditions,
pending IO interruptions have to be cleared. Let's add an interface
for that.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is to better emulate IOAPIC version 0x1X hardware. Linux kernel
leveraged this "feature" to do explicit EOI since EOI register is still
not introduced at that time. This will also fix the issue that level
triggered interrupts failed to work when IR enabled (tested with Linux
kernel version 4.5).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently IOAPIC RO bits can be written. To be better aligned with
hardware, we should let them read-only.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not visible with the default "log" trace backend. With other
backends however trace.h does not include qemu/log.h, resulting in
build failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1463745452-25831-2-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Memory barriers are needed also by Xen and, when the ioeventfd
bugs are fixed, by TCG as well.
sysemu/kvm.h is not anymore needed in sysemu/dma.h, move it to
the actual users.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are obviously critical to understanding interrupt delivery:
gic_enable_irq
gic_disable_irq
gic_set_irq (inbound irq from device models)
gic_update_set_irq (outbound irq to CPU)
gic_acknowledge_irq
The only one that I think might raise eyebrows is gic_update_bestirq, but I've
(sadly) debugged problems that ended up being caused by unexpected priorities.
Knowing that the GIC has an irq ready, but doesn't deliver to the CPU due to
priority, has also proven important.
Signed-off-by: Hollis Blanchard <hollis_blanchard@mentor.com>
Message-id: 1461252281-22399-1-git-send-email-hollis_blanchard@mentor.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: corrected "can not" to "cannot" in error message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Drop the old SysBus init function and use instance_init
* Split the exynos4210_irq_gate_init into an instance_init
and a DeviceClass::realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement a basic ASPEED VIC device model for the AST2400 SoC[1], with
enough functionality to boot an aspeed_defconfig Linux kernel. The model
implements the 'new' (revised) register set: While the hardware exposes
both the new and legacy register sets, accesses to the model's legacy
register set will not be serviced (however the access will be logged).
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-3-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2 introduces a new CPU interface register GICC_DIR, which
allows an OS to split the "priority drop" and "deactivate interrupt"
parts of interrupt completion. Implement this register.
(Note that the register is at offset 0x1000 in the CPU interface,
which means it is on a different 4K page from all the other registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1456854176-7813-1-git-send-email-peter.maydell@linaro.org
Using the return value to report errors is error prone:
- xics_alloc() returns -1 on error but spapr_vio_busdev_realize() errors
on 0
- xics_alloc_block() returns the unclear value of ics->offset - 1 on error
but both rtas_ibm_change_msi() and spapr_phb_realize() error on 0
This patch adds an errp argument to xics_alloc() and xics_alloc_block() to
report errors. The return value of these functions is a valid IRQ number
if errp is NULL. It is undefined otherwise.
The corresponding error traces get promotted to error messages. Note that
the "can't allocate IRQ" error message in spapr_vio_busdev_realize() also
moves to xics_alloc(). Similar error message consolidation isn't really
applicable to xics_alloc_block() because callers have extra context (device
config address, MSI or MSIX).
This fixes the issues mentioned above.
Based on previous work from Brian W. Hart.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This module is specific to the bcm2836 (Pi2). It implements the top
level interrupt controller, and mailboxes used for inter-processor
synchronisation.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-27-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-9-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-7-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
Update the GIC ID registers (registers above 0xfe0) based on the GIC
revision instead of using the sames values for all GIC implementations.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Message-id: 629e7fa5d47f2800e51cc1f18d12635f1eece349.1453333840.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
The errors are all device misconfiguration. All callers use
qdev_init_nofail(), so this patch merely converts hw_error() crashes
into &error_abort crashes. Improvement, because now it crashes closer
to where the misconfiguration bug would be, and a few more bad
examples of hw_error() use are gone.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-3-git-send-email-armbru@redhat.com>
This patch adds support for split IRQ chip mode. When
KVM_CAP_SPLIT_IRQCHIP is enabled:
1.) The PIC, PIT, and IOAPIC are implemented in userspace while
the LAPIC is implemented by KVM.
2.) The software IOAPIC delivers interrupts to the KVM LAPIC via
kvm_set_irq. Interrupt delivery is configured via the MSI routing
table, for which routes are reserved in target-i386/kvm.c then
configured in hw/intc/ioapic.c
3.) KVM delivers IOAPIC EOIs via a new exit KVM_EXIT_IOAPIC_EOI,
which is handled in target-i386/kvm.c and relayed to the software
IOAPIC via ioapic_eoi_broadcast.
Signed-off-by: Matt Gingell <gingell@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upon activating an interrupt, set the corresponding priority bit in the
APR/NSAPR registers without touching the currently set bits. In the event
of nested interrupts, the GIC will then have the information it needs to
restore the priority of the pre-empted interrupt once the higher priority
interrupt finishes execution.
Signed-off-by: François Baldassari <francois@pebble.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
arm_gic.c retrieves CPU number using either NUM_CPU(s) or s->num_cpu.
Such mixed-uses make source code inconsistent. This patch removes
NUM_CPU(s), which was defined for MPCore tweak long ago, and instead
favors s->num_cpu. The source is more consistent after this small tweak.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-id: 1446744293-32365-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the SYSRESETREQ bit of the AIRCR register
for armv7-m (ie. cortex-m3) to trigger a GPIO out.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 29885ffea2577eaf2288c1d17fd87ee951748b49.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, if the kernel does not have live migration API, the migration
will still be attempted, but vGIC save/restore functions will just not do
anything. This will result in a broken machine state.
This patch fixes the problem by adding migration blocker if kernel API is
not supported.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
openpic is a programmable interrupt controller, so
add it to the misc category.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This should help clarify the purpose of the function that returns
the host system's CPU cycle count.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
ppc portion
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After CPU hotplug has been converted to BUS-less hot-plug infrastructure,
the only function ICC bus performs is to propagate reset to LAPICs. However
LAPIC could be reset by registering its reset handler after all device are
initialized.
Do so and drop ~30LOC of not needed anymore ICCBus related code.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When ICC bus/bridge is removed, APIC MMIO will be left
unmapped since it was mapped into system's address space
indirectly by ICC bridge.
Fix it by moving mapping into APIC code, so it would be
possible to remove ICC bus/bridge code later.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Added support emulator for the hmp command "info ioapic"
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-10-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added prefix APIC_ for determining the constant of a particular subsystem,
improve the overall readability and match other constant names.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move apic_get_bit(), apic_set_bit() to apic_internal.h, make the apic_get_ppr
symbol external. It's necessary to work with isr, tmr, irr and ppr outside
hw/intc/apic.c
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-2-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The arbitration register should read to the same value as the
IOAPIC id register. Fixes kvm-unit-tests ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a level-triggered interrupt goes down and back up before the
corresponding EOI, it should be coalesced. This fixes one testcase
in kvm-unit-tests' ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the initial version of KVM-accelerated GICv3 support.
State load and save are not yet supported, live migration is
not possible.
In order to get correct class name in a simpler way, gicv3_class_name()
function is implemented, similar to gic_class_name().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Message-id: 69d8f01d14994d7a1a140e96aef59fd332d02293.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This class is to be used by both software and KVM implementations of GICv3
Currently it is mostly a placeholder, but in future it is supposed to hold
qemu's representation of GICv3 state, which is necessary for migration.
The interface of this class is fully compatible with GICv2 one. This is
done in order to simplify integration with existing code.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: aff8baaee493cdcab0694b4a1d4dd5ff27c37ed2.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A number of source files have statements accidentally
terminated by a double semicolon - eg 'foo = bar;;'.
This is harmless but a mistake none the less.
The tcg/ia64/tcg-target.c file is whitelisted because
it has valid use of ';;' in a comment containing assembly
code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If we directly boot a kernel in NonSecure on a system where the GIC
supports the security extensions then we must cause the GIC to
configure its interrupts into group 1 (NonSecure) rather than the
usual group 0, and with their initial priority set to the highest
NonSecure priority rather than the usual highest Secure priority.
Otherwise the guest kernel will be unable to use any interrupts.
Implement this behaviour, controlled by a flag which we set if
appropriate when the ARM bootloader code calls our ARMLinuxBootIf
interface callback.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-4-git-send-email-peter.maydell@linaro.org
Although we were correctly handling interrupts becoming active
and then inactive, we weren't actually exposing this to the guest
by setting the 'active' flag for the interrupt, so reads
of GICD_ICACTIVERn and GICD_ISACTIVERn would generally incorrectly
return zeroes. Correct this oversight.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-6-git-send-email-peter.maydell@linaro.org
The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Priority values for the GIC are divided into a "group priority"
and a "subpriority" (with the division being determined by the
binary point register). The running priority is only determined
by the group priority of the active interrupts, not the
subpriority. In particular, this means that there can't be more
than one active interrupt at any particular group priority.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-3-git-send-email-peter.maydell@linaro.org
Change the implementation of the Interrupt Control and State Register
in the v7M NVIC to not use the running_irq and last_active internal
state fields in the GIC. These fields don't correspond to state in
a real GIC and will be removed soon.
The changes to the ICSR are:
* the VECTACTIVE field is documented as identical to the IPSR[8:0]
field, so implement it that way
* implement RETTOBASE via looking at the active state bits
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-2-git-send-email-peter.maydell@linaro.org
When we add new adapter routes we call kvm_irqchip_add_route() for every
virtqueue and in the same step also do the KVM_SET_GSI_ROUTING ioctl.
This is unnecessary costly as the interface allows us to set multiple
routes in one go. Let's first add all routes to the table stored in the
global kvm_state and then do the ioctl to commit the routes to the
in-kernel irqchip.
This saves us several ioctls to the kernel where for each call a list
is reallocated and populated.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When supporting CPU hot removal by parking the vCPU fd and reusing
it during hotplug again, there can be cases where we try to reenable
KVM_CAP_IRQ_XICS CAP for the vCPU for which it was already enabled.
Introduce a boolean member in ICPState to track this and don't
reenable the CAP if it was already enabled earlier.
Re-enabling this CAP should ideally work, but currently it results in
kernel trying to create and associate ICP with this vCPU and that
fails since there is already an ICP associated with it. Hence this
patch is needed to work around this problem in the kernel.
This change allows CPU hot removal to work for sPAPR.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code for -machine pseries maintains a global sPAPREnvironment structure
which keeps track of general state information about the guest platform.
This predates the existence of the MachineState structure, but performs
basically the same function.
Now that we have the generic MachineState, fold sPAPREnvironment into
sPAPRMachineState, the pseries specific subclass of MachineState.
This is mostly a matter of search and replace, although a few places which
relied on the global spapr variable are changed to find the structure via
qdev_get_machine().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The arm_gic_kvm now calls kvm_irqchip_set_qemuirq_gsi to build
the hash table storing qemu_irq/gsi mappings. From that point on
irqfd can be setup directly from the qemu_irq using
kvm_irqchip_add_irqfd_notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
This patch fixes so that gic_update always updates all the cores with
new pending irq states. If the function returns early it is possible
to get interrupts that has already been acknowledged.
Signed-off-by: Johan Karlsson <johan.karlsson@enea.com>
[PMM: rebased to apply to current master]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbvwjAAoJEL7lnXSkw9fbaFwIAIh6PN5v6fvuEjnPX5ijHZC2
7iJoFd0I2cYrxgLe4xONFX9qzV5vgdEAJfXCljVCKAmzu5RK7G0ZSW81sJ3t6Mp8
kA8buJeyTp2UcTlDrC3qji8ScEIj+g8I9tKGflNVI2uDAVumMBPqnJNSFhbaqYlu
SEq+4y/D3J6xPzr7NhyHliG0NmxJrIn6QCtux5djj3xO4KXfp1j2YQCPKhYjkRlW
wHfqeD7x9LX6875FX3csgfPsYIycW0WYtba2adTe0vbTsclOY0CU3ho8HPeXgHE6
WQj6KYGT8Fo0zmK8UV0Jmok7+hZoxXXInf6vY+sSY58oe71FgdxNwLvIC6N0eQc=
=AALk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mjt/tags/pull-trivial-patches-2015-06-03' into staging
trivial patches for 2015-06-03
# gpg: Signature made Wed Jun 3 14:07:47 2015 BST using RSA key ID A4C3D7DB
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
* remotes/mjt/tags/pull-trivial-patches-2015-06-03: (30 commits)
configure: postfix --extra-cflags to QEMU_CFLAGS
cadence_gem: Fix Rx buffer size field mask
slirp: use less predictable directory name in /tmp for smb config (CVE-2015-4037)
translate-all: delete prototype for non-existent function
Add -incoming help text
hw/display/tc6393xb.c: Fix misusing qemu_allocate_irqs for single irq
hw/arm/nseries.c: Fix misusing qemu_allocate_irqs for single irq
hw/alpha/typhoon.c: Fix misusing qemu_allocate_irqs for single irq
hw/unicore32/puv3.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/milkymist.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/lm32_boards.c: Fix misusing qemu_allocate_irqs for single irq
hw/ppc/prep.c: Fix misusing qemu_allocate_irqs for single irq
hw/sparc/sun4m.c: Fix misusing qemu_allocate_irqs for single irq
hw/timer/arm_timer.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/i82378.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/lpc_ich9.c: Fix misusing qemu_allocate_irqs for single irq
hw/i386/pc: Fix misusing qemu_allocate_irqs for single irq
hw/intc/exynos4210_gic.c: Fix memory leak by adjusting order
hw/arm/omap_sx1.c: Fix memory leak spotted by valgrind
hw/ppc/e500.c: Fix memory leak
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VKFL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
X86 queue 2015-06-02
# gpg: Signature made Tue Jun 2 20:21:17 2015 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
arch_init: Drop target-x86_64.conf
target-i386: Register QOM properties for feature flags
apic: convert ->busdev.qdev casts to C casts
target-i386: Fix signedness of MSR_IA32_APICBASE_BASE
pc: Ensure non-zero CPU ref count after attaching to ICC bus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use C casts to avoid accessing ICCDevice's qdev field
directly.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
After introduction of kvm_arch_msi_data_to_gsi, kvm_gsi_direct_mapping
now can be set on ARM. Also kvm_msi_via_irqfd_allowed can be set,
depending on kernel irqfd support, hence enabling VIRTIO-PCI with
vhost back-end.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support to gic_update() for determining the current IRQ
and FIQ status when interrupt grouping is supported. This
simply requires that instead of always raising IRQ we
check the group of the highest priority pending interrupt
and the GICC_CTLR.FIQEn bit to see whether we should raise
IRQ or FIQ.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-15-git-send-email-peter.maydell@linaro.org
Grouping (GICv2) and Security Extensions change the behavior of IAR
reads. Acknowledging Group0 interrupts is only allowed from Secure
state and acknowledging Group1 interrupts from Secure state is only
allowed if AckCtl bit is set.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-14-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-14-git-send-email-greg.bellows@linaro.org
[PMM: simplify significantly by reusing the existing
gic_get_current_pending_irq() rather than reimplementing the
same logic here]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behavior of EOIR
writes. Completing Group0 interrupts is only allowed from Secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-13-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-13-git-send-email-greg.bellows@linaro.org
[PMM: Rather than go to great lengths to ignore the UNPREDICTABLE case
of a Secure EOI of a Group1 (NS) irq with AckCtl == 0, we just let
it fall through; add a comment about it.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behaviour of reads
of the highest priority pending interrupt register (ICCHPIR/GICC_HPPIR).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-12-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-12-git-send-email-greg.bellows@linaro.org
[PMM: make utility fn static; coding style fixes; AckCtl has an effect
for GICv2 without security extensions as well; removed checks on enable
bits because these are done when we set current_pending[cpu]]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GICs with Security Extensions restrict the non-secure view of the
interrupt priority and priority mask registers.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-11-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-15-git-send-email-greg.bellows@linaro.org
[PMM: minor code tweaks; fixed missing masking in gic_set_priority_mask
and gic_set_priority]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For GICs with Security Extensions Non-secure reads have a restricted
view on the current running priority.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-10-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-11-git-send-email-greg.bellows@linaro.org
[PMM: make function static, minor comment tweak]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is banked in GICs with Security Extensions. Storing the
non-secure copy of BPR in the abpr, which is an alias to the non-secure
copy for secure access. ABPR itself is only accessible from secure state
if the GIC implements Security Extensions.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-8-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-10-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to fix style issues and correct handling of GICv2
without security extensions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the GIC base class has state fields for the GICD_IGROUPRn
registers, make kvm_arm_gic_get() and kvm_arm_gic_put() write and
read them. This allows us to remove the check that made us
fail migration if the guest had set any of the group register bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-6-git-send-email-peter.maydell@linaro.org
The Interrupt Group Registers allow the guest to configure interrupts
into one of two groups, where Group0 are higher priority and may
be routed to IRQ or FIQ, and Group1 are lower priority and always
routed to IRQ. (In a GIC with the security extensions Group0 is
Secure interrupts and Group 1 is NonSecure.)
The GICv2 always supports interrupt grouping; the GICv1 does only
if it implements the security extensions.
This patch implements the ability to read and write the registers;
the actual functionality the bits control will be added in a
subsequent patch.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-5-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-7-git-send-email-greg.bellows@linaro.org
[PMM: bring GIC_*_GROUP macros into line with the others, ie a
simple SET/CLEAR/TEST rather than GROUP0/GROUP1;
utility gic_has_groups() function;
minor style fixes;
bump vmstate version]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the GIC's MMIO callback functions to the read_with_attrs
and write_with_attrs functions which provide MemTxAttrs. This will
allow the GIC to correctly handle secure and nonsecure register
accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-4-git-send-email-peter.maydell@linaro.org
Add a QOM property which allows the GIC Security Extensions to be
enabled. These are an optional part of the GICv1 and GICv2 architecture.
This commit just adds the property and some sanity checks that it
is only enabled on GIC revisions that support it.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-3-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-5-git-send-email-greg.bellows@linaro.org
[PMM: changed property name, added checks that it isn't set for
older GIC revisions or if using the KVM VGIC; reworded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the outbound FIQ lines from the GIC to the CPUs; these are
used if the GIC has security extensions or grouping support.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-2-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-2-git-send-email-greg.bellows@linaro.org
[PMM: added FIQ lines to kvm-arm-gic so its interface is the same;
tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
