The read_tcnt() function calculates the TCNT register values for the
two channels of the timer module; it sets these up in the local
tcnt[] array, and eventually returns either one or both of them,
depending on whether the access is 8 or 16 bits. However, not all of
the code paths through this function set both elements of this array:
if the guest has programmed the TCCR.CSS register fields to values
which are either documented as not to be used or which QEMU does not
implement, then the function will return uninitialized data. (This
was spotted by Coverity.)
Add the missing CSS cases to this code, so that we return a
consistent value instead of uninitialized data, and so the code
structure indicates what's happening.
Fixes: CID 1429976
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219223241.16344-3-peter.maydell@linaro.org
The #defines INTERNAL and CASCADING represent different possible
values for the TCCR.CSS register field; prefix them with CSS_ to make
this more obvious, before we add more defines to represent the
other possible values of the field in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219223241.16344-2-peter.maydell@linaro.org
Now that the Xilinx CSU DMA model is implemented, the existing
DMA related dead codes in the ZynqMP QSPI are useless and should
be removed. The maximum register number is also updated to only
include the QSPI registers.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xilinx_spips.c,
as reported by:
$ ./scripts/checkpatch.pl hw/ssi/xilinx_spips.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ZynqMP QSPI supports SPI transfer using DMA mode, but currently this
is unimplemented. When QSPI is programmed to use DMA mode, QEMU will
crash. This is observed when testing VxWorks 7.
This adds a Xilinx CSU DMA model and the implementation is based on
https://github.com/Xilinx/qemu/blob/master/hw/dma/csu_stream_dma.c.
The DST part of the model is verified along with ZynqMP GQSPI model.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
Implement the minor changes required to the SCC block for AN547 images:
* CFG2 and CFG5 exist (like AN524)
* CFG3 is reserved (like AN524)
* CFG0 bit 1 is CPU_WAIT; we don't implement it, but note this
in the TODO comment
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-40-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
We've already broken migration compatibility for all the MPS
boards, so we might as well take advantage of this to simplify
the vmstate for the FPGAIO device by folding the counters
subsection into the main vmstate description.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-38-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-200 and SSE-300 have different PID register values from the
IoTKit for the sysctl register block. We incorrectly implemented the
SSE-200 with the same PID values as IoTKit. Fix the SSE-200 bug and
report these register values for SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-19-peter.maydell@linaro.org
The sysctl PDCM_PD_*_SENSE registers control various power domains in
the system and allow the guest to configure which conditions keep a
power domain awake and what power state to use when the domain is in
a low power state. QEMU doesn't model power domains, so for us these
registers are dummy reads-as-written implementations.
The SSE-300 has a different power domain setup, so the set of
registers is slightly different:
Offset SSE-200 SSE-300
---------------------------------------------------
0x200 PDCM_PD_SYS_SENSE PDCM_PD_SYS_SENSE
0x204 reserved PDCM_PD_CPU0_SENSE
0x208 reserved reserved
0x20c PDCM_PD_SRAM0_SENSE reserved
0x210 PDCM_PD_SRAM1_SENSE reserved
0x214 PDCM_PD_SRAM2_SENSE PDCM_PD_VMR0_SENSE
0x218 PDCM_PD_SRAM3_SENSE PDCM_PD_VMR1_SENSE
Offsets 0x200 and 0x208 are the same for both, so handled in a
previous commit; here we deal with 0x204, 0x20c, 0x210, 0x214, 0x218.
(We can safely add new lines to the SSE300 vmstate because no board
uses this device in an SSE300 yet.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-18-peter.maydell@linaro.org
The SSE-300 has a new PWRCTRL register at offset 0x1fc (previously
reserved). This register controls accessibility of some registers
in the Power Policy Units (PPUs). Since QEMU doesn't implement
the PPUs, we don't need to implement any real behaviour for this
register, so we just handle the UNLOCK bit which controls whether
writes to the register itself are permitted and otherwise make it
be reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-17-peter.maydell@linaro.org
The SSE-300 has only one CPU and so no INITSVTOR1. It does
have INITSVTOR0, but unlike the SSE-200 this register now
has a LOCK bit which can be set to 1 to prevent any further
writes to the register. Implement these differences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-16-peter.maydell@linaro.org
In the SSE-300 the CPU_WAIT and NMI_ENABLE registers have
moved offsets, so they are now where the SSE-200's WICCTRL
and EWCTRL were. The SSE-300 does not have WICCTLR or EWCTRL
at all, and the old offsets are reserved:
Offset SSE-200 SSE-300
-----------------------------------
0x118 CPUWAIT reserved
0x118 NMI_ENABLE reserved
0x120 WICCTRL CPUWAIT
0x124 EWCTRL NMI_ENABLE
Handle this reshuffle, and the fact that SSE-300 has only
one CPU and so only one active bit in CPUWAIT.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-15-peter.maydell@linaro.org
The SSE-300's iokit-sysctl device is similar to the SSE-200, but
some registers have moved address or have different behaviours.
In this commit we add case statements for the registers where
the SSE-300 and SSE-200 have the same behaviour. Some registers
are the same on all SSE versions and so need no code change at all.
Putting both of these categories together covers:
0x0 SECDBGSTAT
0x4 SECDBGSET
0x8 SECDBGCLR
0xc SCSECCTRL
0x10 CLK_CFG0 -- this is like SSE-200 FCLK_DIV but with a
different set of clocks being controlled; our implementation
is a dummy reads-as-written anyway
0x14 CLK_CFG1 -- similar to SSE-200 SYSCLK_DIV; our implementation
is a dummy
0x18 CLK_FORCE -- similar to SSE-200 but different bit allocations;
we have a dummy implementation
0x100 RESET_SYNDROME -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x104 RESET_MASK -- bit allocation differs from SSE-200 but our
implementation is a dummy
0x108 SWRESET
0x10c GRETREG
0x200 PDCM_PD_SYS_SENSE -- some bit allocations differ, but our
implementation is a dummy
We also need to migrate the state of these registers which are shared
between the SSE-200 and SSE-300, so update the vmstate 'needed'
function to do this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-14-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
Remove the is_sse200 flag in favour of just directly testing the new
sse_version field.
Since some of these registers exist in the SSE-300 but some do not or
have different behaviour, we expand out the if() statements in the
read and write functions into switch()es, so we have an easy place to
put SSE-300 specific behaviour.
(Until we do add the SSE-300 behaviour, the thing preventing us
reaching the "unreachable" default cases is that armsse.c doesn't
yet pass us an ARMSSE_SSE300 version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-7-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Use the new clock_ns_to_ticks() function in npcm7xx_timer where
appropriate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-5-peter.maydell@linaro.org
Add a new callback event type ClockPreUpdate, which is called on
period changes before the period is updated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-3-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
-----BEGIN PGP SIGNATURE-----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=nphT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210308' into staging
target-arm queue:
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
# gpg: Signature made Mon 08 Mar 2021 11:56:24 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210308: (49 commits)
hw/arm/mps2: Update old infocenter.arm.com URLs
docs/system/arm/mps2.rst: Document the new mps3-an524 board
hw/arm/mps2-tz: Provide PL031 RTC on mps3-an524
hw/arm/mps2-tz: Stub out USB controller for mps3-an524
hw/arm/mps2-tz: Add new mps3-an524 board
hw/arm/mps2-tz: Get armv7m_load_kernel() size argument from RAMInfo
hw/arm/mps2-tz: Support ROMs as well as RAMs
hw/arm/mps2-tz: Set MachineClass default_ram info from RAMInfo data
hw/arm/mps2-tz: Make RAM arrangement board-specific
hw/arm/mps2-tz: Allow boards to have different PPCInfo data
hw/arm/mps2-tz: Size the uart-irq-orgate based on the number of UARTs
hw/arm/mps2-tz: Move device IRQ info to data structures
hw/arm/mps2-tz: Allow PPCPortInfo structures to specify device interrupts
hw/arm/mps2-tz: Correct wrong interrupt numbers for DMA and SPI
hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524
hw/arm/mps2-tz: Make number of IRQs board-specific
hw/arm/mps2-tz: Condition IRQ splitting on number of CPUs, not board type
hw/arm/mps2-tz: Make FPGAIO switch and LED config per-board
hw/misc/mps2-fpgaio: Support SWITCH register
hw/misc/mps2-fpgaio: Make number of LEDs configurable by board
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
