There is no need to "force an hs exception" as the current privilege
level, the state of the global ie and of the delegation registers should
be enough to route the interrupt to the appropriate privilege level in
riscv_cpu_do_interrupt. The is true for both asynchronous and
synchronous exceptions, specifically, guest page faults which must be
hardwired to zero hedeleg. As such the hs_force_except mechanism can be
removed.
Signed-off-by: Jose Martins <josemartins90@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211026145126.11025-3-josemartins90@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
VS interrupts (2, 6, 10) were not correctly forwarded to hs-mode when
not delegated in hideleg (which was not being taken into account). This
was mainly because hs level sie was not always considered enabled when
it should. The spec states that "Interrupts for higher-privilege modes,
y>x, are always globally enabled regardless of the setting of the global
yIE bit for the higher-privilege mode." and also "For purposes of
interrupt global enables, HS-mode is considered more privileged than
VS-mode, and VS-mode is considered more privileged than VU-mode". Also,
vs-level interrupts were not being taken into account unless V=1, but
should be unless delegated.
Finally, there is no need for a special case for to handle vs interrupts
as the current privilege level, the state of the global ie and of the
delegation registers should be enough to route all interrupts to the
appropriate privilege level in riscv_cpu_do_interrupt.
Signed-off-by: Jose Martins <josemartins90@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211026145126.11025-2-josemartins90@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The position of this read-only field is dependent on the current xlen.
Rather than having to compute that difference in many places, compute
it only on read.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-16-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use the official debug read interface to the csrs,
rather than referencing the env slots directly.
Put the list of csrs to dump into a table.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-15-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Most shift instructions require a separate implementation
for RV32 when TARGET_LONG_BITS == 64.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-14-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The count zeros instructions require a separate implementation
for RV32 when TARGET_LONG_BITS == 64.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-13-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When target_long is 64-bit, we still want a 32-bit bswap for rev8.
Since this opcode is specific to RV32, we need not conditionalize.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-12-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The multiply high-part instructions require a separate
implementation for RV32 when TARGET_LONG_BITS == 64.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-11-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In preparation for RV128, consider more than just "w" for
operand size modification. This will be used for the "d"
insns from RV128 as well.
Rename oper_len to get_olen to better match get_xlen.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-10-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In preparation for RV128, replace a simple predicate
with a more versatile test.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-9-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We're currently assuming SEW <= 3, and the "else" from
the SEW == 3 must be less. Use a switch and explicitly
bound both SEW and SEQ for all cases.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-8-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use the same REQUIRE_64BIT check that we use elsewhere,
rather than open-coding the use of is_32bit.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-7-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Begin adding support for switching XLEN at runtime. Extract the
effective XLEN from MISA and MSTATUS and store for use during translation.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-6-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Shortly, the set of supported XL will not be just 32 and 64,
and representing that properly using the enumeration will be
imperative.
Two places, booting and gdb, intentionally use misa_mxl_max
to emphasize the use of the reset value of misa.mxl, and not
the current cpu state.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-5-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The hw representation of misa.mxl is at the high bits of the
misa csr. Representing this in the same way inside QEMU
results in overly complex code trying to check that field.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-4-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the MXL_RV* defines to enumerators.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-3-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the function to cpu_helper.c, as it is large and growing.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-2-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Organise the CPU properties so that standard extensions come first
then followed by experimental extensions.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: b6598570f60c5ee7f402be56d837bb44b289cc4d.1634531504.git.alistair.francis@wdc.com
Since commit 1a9540d1f1
("target/riscv: Drop support for ISA spec version 1.09.1")
these definitions are unused, remove them.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: f4d8a7a035f39c0a35d44c1e371c5c99cc2fa15a.1634531504.git.alistair.francis@wdc.com
TB_FLAGS mem_idx bits was extended from 2 bits to 3 bits in
commit: c445593, but other TB_FLAGS bits for rvv and rvh were
not shift as well so these bits may overlap with each other when
rvv is enabled.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211015074627.3957162-2-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The earlier implementation fell into a corner case for bytes that were
0x01, giving a wrong result (but not affecting our application test
cases for strings, as an ASCII value 0x01 is rare in those...).
This changes the algorithm to:
1. Mask out the high-bit of each bytes (so that each byte is <= 127).
2. Add 127 to each byte (i.e. if the low 7 bits are not 0, this will overflow
into the highest bit of each byte).
3. Bitwise-or the original value back in (to cover those cases where the
source byte was exactly 128) to saturate the high-bit.
4. Shift-and-mask (implemented as a mask-and-shift) to extract the MSB of
each byte into its LSB.
5. Multiply with 0xff to fan out the LSB to all bits of each byte.
Fixes: d7a4fcb034 ("target/riscv: Add orc.b instruction for Zbb, removing gorc/gorci")
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reported-by: Vincent Palatin <vpalatin@rivosinc.com>
Tested-by: Vincent Palatin <vpalatin@rivosinc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211013184125.2010897-1-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Ensure the columns for all of the register names and values line up.
No functional change, just a minor tweak to the output.
Signed-off-by: Travis Geiselbrecht <travisg@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211009055019.545153-1-travisg@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
oprsz and maxsz are passed with the same value in commit: eee2d61e20.
However, vmv.v.v was missed in that commit and should pass the same
value as well in its tcg_gen_gvec_2_ptr() call.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211007081803.1705656-1-frank.chang@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
GDB single-stepping is now handled generically, which means
we don't need to do anything in the wrappers.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We have already set DISAS_NORETURN in generate_exception,
which makes the exit_tb unreachable.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When V=1, both vsstauts.FS and HS-level sstatus.FS are in effect.
Modifying the floating-point state when V=1 causes both fields to
be set to 3 (Dirty).
However, it's possible that HS-level sstatus.FS is Clean and VS-level
vsstatus.FS is Dirty at the time mark_fs_dirty() is called when V=1.
We can't early return for this case because we still need to set
sstatus.FS to Dirty according to spec.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Vincent Chen <vincent.chen@sifive.com>
Tested-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210921020234.123448-1-frank.chang@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
With everything classified as Zb[abcs] and pre-0.93 draft-B
instructions that are not part of Zb[abcs] removed, we can remove the
remaining support code for RVB.
Note that RVB has been retired for good and misa.B will neither mean
'some' or 'all of' Zb*:
https://lists.riscv.org/g/tech-bitmanip/message/532
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-16-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 1.0.0 version of Zbb does not contain pack/packu/packh. However, a
zext.h instruction is provided (built on pack/packh from pre-0.93
draft-B) is available.
This commit adds zext.h and removes the pack* instructions.
Note that the encodings for zext.h are different between RV32 and
RV64, which is handled through REQUIRE_32BIT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210911140016.834071-15-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 1.0.0 version of Zbb does not contain grev/grevi. Instead, a
rev8 instruction (equivalent to the rev8 pseudo-instruction built on
grevi from pre-0.93 draft-B) is available.
This commit adds the new rev8 instruction and removes grev/grevi.
Note that there is no W-form of this instruction (both a
sign-extending and zero-extending 32-bit version can easily be
synthesized by following rev8 with either a srai or srli instruction
on RV64) and that the opcode encodings for rev8 in RV32 and RV64 are
different.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210911140016.834071-14-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
With the changes to Zb[abcs], there's some encodings that are
different in RV64 and RV32 (e.g., for rev8 and zext.h). For these,
we'll need a helper macro allowing us to select on RV32, as well.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-13-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 1.0.0 version of Zbb does not contain gorc/gorci. Instead, a
orc.b instruction (equivalent to the orc.b pseudo-instruction built on
gorci from pre-0.93 draft-B) is available, mainly targeting
string-processing workloads.
This commit adds the new orc.b instruction and removed gorc/gorci.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210911140016.834071-12-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This reassigns the instructions that are part of Zbb into it, with the
notable exceptions of the instructions (rev8, zext.w and orc.b) that
changed due to gorci, grevi and pack not being part of Zb[abcs].
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-11-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following instructions are part of Zbc:
- clmul
- clmulh
- clmulr
Note that these instructions were already defined in the pre-0.93 and
the 0.93 draft-B proposals, but had not been omitted in the earlier
addition of draft-B to QEmu.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210911140016.834071-10-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following instructions are part of Zbs:
- b{set,clr,ext,inv}
- b{set,clr,ext,inv}i
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-9-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Zb[abcs] ratification package does not include the proposed
shift-one instructions. There currently is no clear plan to whether
these (or variants of them) will be ratified as Zbo (or a different
extension) or what the timeframe for such a decision could be.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-8-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Zbs 1.0.0 (just as the 0.93 draft-B before) does not provide for W-form
instructions for Zbs (single-bit instructions). Remove them.
Note that these instructions had already been removed for the 0.93
version of the draft-B extention and have not been present in the
binutils patches circulating in January 2021.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-7-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following instructions are part of Zba:
- add.uw (RV64 only)
- sh[123]add (RV32 and RV64)
- sh[123]add.uw (RV64-only)
- slli.uw (RV64-only)
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-6-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The bitmanipulation ISA extensions will be ratified as individual
small extension packages instead of a large B-extension. The first
new instructions through the door (these have completed public review)
are Zb[abcs].
This adds new 'x-zba', 'x-zbb', 'x-zbc' and 'x-zbs' properties for
these in target/riscv/cpu.[ch].
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210911140016.834071-5-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Assume clzw being executed on a register that is not sign-extended, such
as for the following sequence that uses (1ULL << 63) | 392 as the operand
to clzw:
bseti a2, zero, 63
addi a2, a2, 392
clzw a3, a2
The correct result of clzw would be 23, but the current implementation
returns -32 (as it performs a 64bit clz, which results in 0 leading zero
bits, and then subtracts 32).
Fix this by changing the implementation to:
1. shift the original register up by 32
2. performs a target-length (64bit) clz
3. return 32 if no bits are set
Marking this instruction as 'w-form' (i.e., setting ctx->w) would not
correctly model the behaviour, as the instruction should not perform
a zero-extensions on the input (after all, it is not a .uw instruction)
and the result is always in the range 0..32 (so neither a sign-extension
nor a zero-extension on the result will ever be needed). Consequently,
we do not set ctx->w and mark the instruction as EXT_NONE.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: LIU Zhiwei<zhiwei_liu@c-sky.com>
Message-id: 20210911140016.834071-4-philipp.tomsich@vrull.eu
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The refactored gen_clzw() uses ret as its argument, instead of arg1.
Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210911140016.834071-3-philipp.tomsich@vrull.eu
Fixes: 6090391505 ("target/riscv: Add DisasExtend to gen_unary")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Following the recent changes in translate.c, gen_add_uw() causes
failures on CF3 and SPEC2017 due to the reuse of arg1. Fix these
regressions by introducing a temporary.
Signed-off-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210911140016.834071-2-philipp.tomsich@vrull.eu
Fixes: 191d1dafae ("target/riscv: Add DisasExtend to gen_arith*")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
While we may have had some thought of allowing system-mode
to return from this hook, we have no guests that require this.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
