The smmuv3_record_event() function that generates the F_STE_FETCH error
uses the EVT_SET_ADDR macro to record the fetch address, placing it in
32-bit words 4 and 5.
The correct position for this address is in words 6 and 7, per the
SMMUv3 Architecture Specification.
Update the function to use the EVT_SET_ADDR2 macro instead, which is the
macro intended for writing to these words.
ref. ARM IHI 0070C, section 7.3.4.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-7-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bit offsets in the EVT_SET_ADDR2 macro do not match those specified
in the ARM SMMUv3 Architecture Specification. In all events that use
this macro, e.g. F_WALK_EABT, the faulting fetch address or IPA actually
occupies the 32-bit words 6 and 7 in the event record contiguously, with
the upper and lower unused bits clear due to alignment or maximum
supported address bits. How many bits are clear depends on the
individual event type.
Update the macro to write to the correct words in the event record so
that guest drivers can obtain accurate address information on events.
ref. ARM IHI 0070C, sections 7.3.12 through 7.3.16.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-6-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Per the specification, and as observed in hardware, the SMMUv3 aligns
the SMMU_STRTAB_BASE address to the size of the table by masking out the
respective least significant bits in the ADDR field.
Apply this masking logic to our smmu_find_ste() lookup function per the
specification.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-5-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When checking whether a stream ID is in range of the stream table, we
have so far been only checking it against our implementation limit
(SMMU_IDR1_SIDSIZE). However, the guest can program the
STRTAB_BASE_CFG.LOG2SIZE field to a size that is smaller than this
limit.
Check the stream ID against this limit as well to match the hardware
behavior of raising C_BAD_STREAMID events in case the limit is exceeded.
Also, ensure that we do not go one entry beyond the end of the table by
checking that its index is strictly smaller than the table size.
ref. ARM IHI 0070C, section 6.3.24.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-4-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are two issues with the current value of SMMU_BASE_ADDR_MASK:
- At the lower end, we are clearing bits [4:0]. Per the SMMUv3 spec,
we should also be treating bit 5 as zero in the base address.
- At the upper end, we are clearing bits [63:48]. Per the SMMUv3 spec,
only bits [63:52] must be explicitly treated as zero.
Update the SMMU_BASE_ADDR_MASK value to mask out bits [63:52] and [5:0].
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-3-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the SMMU_STRTAB_BASE register, the stream table base address only
occupies bits [51:6]. Other bits, such as RA (bit [62]), must be masked
out to obtain the base address.
The branch for 2-level stream tables correctly applies this mask by way
of SMMU_BASE_ADDR_MASK, but the one for linear stream tables does not.
Apply the missing mask in that case as well so that the correct stream
base address is used by guests which configure a linear stream table.
Linux guests are unaffected by this change because they choose a 2-level
stream table layout for the QEMU SMMUv3, based on the size of its stream
ID space.
ref. ARM IHI 0070C, section 6.3.23.
Signed-off-by: Simon Veith <sveith@amazon.de>
Acked-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1576509312-13083-2-git-send-email-sveith@amazon.de
Cc: Eric Auger <eric.auger@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Acked-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This matches the configuration set by u-boot on the AST2600.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 080ca1267a09381c43cf3c50d434fb6c186f2b6e.1576215453.git-series.andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit aa57020774, by mistake used MachineClass::numa_mem_supported
to check if NUMA is supported by machine and also as unrelated change
set it to true for sbsa-ref board.
Luckily change didn't break machines that support NUMA, as the field
is set to true for them.
But the field is not intended for checking if NUMA is supported and
will be flipped to false within this release for new machine types.
Fix it:
- by using previously used condition
!mc->cpu_index_to_instance_props || !mc->get_default_cpu_node_id
the first time and then use MachineState::numa_state down the road
to check if NUMA is supported
- dropping stray sbsa-ref chunk
Fixes: aa57020774
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1576154936-178362-3-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We are going to remove the bitrotten bluetooth backend, so we can
not use it in the n800 and n810 machines anymore. Replace the chardev
here with a "null" chardev and stop including the "hw/bt.h" header.
I am not aware of a full working N8x0 environment that can be used to
test these machines, but the Linux kernel from the Meego project that
can be found on http://stskeeps.subnetmask.net/meego-n8x0/ still seems
to boot as far as it did before.
Message-Id: <20191120091014.16883-2-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
-----BEGIN PGP SIGNATURE-----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=V+AK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20191216-1' into staging
target-arm queue:
* Add support for Cortex-M7 CPU
* exynos4210_gic: Suppress gcc9 format-truncation warnings
* aspeed: Various minor bug fixes and improvements
* aspeed: Add support for the tacoma-bmc board
* Honour HCR_EL32.TID1 and .TID2 trapping requirements
* Handle trapping to EL2 of AArch32 VMRS instructions
* Handle AArch32 CP15 trapping via HSTR_EL2
* Add support for missing Jazelle system registers
* arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on
* Add support for DC CVAP & DC CVADP instructions
* Fix assertion when SCR.NS is changed in Secure-SVC &c
* enable SHPC native hot plug in arm ACPI
# gpg: Signature made Mon 16 Dec 2019 11:08:07 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20191216-1: (34 commits)
target/arm: ensure we use current exception state after SCR update
hw/arm/virt: Simplify by moving the gic in the machine state
hw/arm/acpi: enable SHPC native hot plug
hw/arm/acpi: simplify AML bit and/or statement
hw/arm/sbsa-ref: Simplify by moving the gic in the machine state
target/arm: Add support for DC CVAP & DC CVADP ins
migration: ram: Switch to ram block writeback
Memory: Enable writeback for given memory region
tcg: cputlb: Add probe_read
arm/arm-powerctl: set NSACR.{CP11, CP10} bits in arm_set_cpu_on()
target/arm: Add support for missing Jazelle system registers
target/arm: Handle AArch32 CP15 trapping via HSTR_EL2
target/arm: Handle trapping to EL2 of AArch32 VMRS instructions
target/arm: Honor HCR_EL2.TID1 trapping requirements
target/arm: Honor HCR_EL2.TID2 trapping requirements
aspeed: Change the "nic" property definition
aspeed: Change the "scu" property definition
gpio: fix memory leak in aspeed_gpio_init()
aspeed: Add support for the tacoma-bmc board
aspeed: Remove AspeedBoardConfig array and use AspeedMachineClass
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191209090306.20433-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the introduction of generic PCIe root port and PCIe-PCI bridge,
we will also have SHPC controller on ARM, so just enable SHPC native
hot plug.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-3-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The last argument of AML bit and/or statement is the target variable,
so we don't need to use a NULL target and then an additional store
operation; using just aml_and() or aml_or() statement is enough.
Also update tests/data/acpi/virt/DSDT* to pass "make check".
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Message-id: 20191209063719.23086-2-guoheyi@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191206162303.30338-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed MII model has a link pointing to its associated FTGMAC100
NIC in the machine.
Change the "nic" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed Watchdog and Timer models have a link pointing to the SCU
controller model of the machine.
Change the "scu" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Tacoma BMC board is replacement board for the BMC of the OpenPOWER
Witherspoon system. It uses a AST2600 SoC instead of a AST2500 and the
I2C layout is the same as it controls the same main board. Used for HW
bringup.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedBoardConfig is a redundant way to define class attributes and it
complexifies the machine definition and initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 5.0 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1; I'll leave changing this (if desired) to the respective
maintainers.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191112104811.30323-1-cohuck@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The boot.c code usually puts the CPU into NS mode directly when it is
booting a kernel. Since fc1120a7f5 this has included a
requirement to set NSACR to give NS state access to the FPU; we fixed
that for the usual code path in ece628fcf6. However, it is also
possible for a board model to request an alternative mode of booting,
where its 'board_setup' code hook runs in Secure state and is
responsible for doing the S->NS transition after it has done whatever
work it must do in Secure state. In this situation the board_setup
code now also needs to update NSACR.
This affects all boards which set info->secure_board_setup, which is
currently the 'raspi' and 'highbank' families. They both use the
common arm_write_secure_board_setup_dummy_smc().
Set the NSACR CP11 and CP10 bits in the code written by that
function, to allow FPU access in Non-Secure state when using dummy
SMC setup routine. Otherwise an AArch32 kernel booted on the
highbank or raspi boards will UNDEF as soon as it tries to use the
FPU.
Update the comment describing secure_board_setup to note the new
requirements on users of it.
This fixes a kernel panic when booting raspbian on raspi2.
Successfully tested with:
2017-01-11-raspbian-jessie-lite.img
2018-11-13-raspbian-stretch-lite.img
2019-07-10-raspbian-buster-lite.img
Fixes: fc1120a7f5
Signed-off-by: Clement Deschamps <clement.deschamps@greensocs.com>
Tested-by: Laurent Bonnans <laurent.bonnans@here.com>
Message-id: 20191104151137.81931-1-clement.deschamps@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: updated comment to boot.h to note new requirement on
users of secure_board_setup; edited/rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rebuild hflags when modifying CPUState at boot.
Fixes: e979972a6a
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191031040830.18800-2-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
write_secondary_boot() is used in SMP configurations where the
CPU address space might not be the main System Bus.
The rom_add_blob_fixed_as() function allow us to specify an
address space. Use it to write each boot blob in the corresponding
CPU address space.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
write_secondary_boot() is used in SMP configurations where the
CPU address space might not be the main System Bus.
The rom_add_blob_fixed_as() function allow us to specify an
address space. Use it to write each boot blob in the corresponding
CPU address space.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we are going to add more core-specific fields, add a 'cpu'
structure and move the ARMCPU field there as 'core'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This file creates the BCM2836/BCM2837 blocks.
The biggest differences with the BCM2838 we are going to add, are
the base addresses of the interrupt controller and the peripherals.
Add these addresses in the BCM283XInfo structure to make this
block more modular. Remove the MCORE_OFFSET offset as it is
not useful and rather confusing.
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the recently added SYS_timer.
Now U-Boot does not hang anymore polling a free running counter
stuck at 0.
This timer is also used by the Linux kernel thermal subsystem.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Map the thermal sensor in the BCM2835 block.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PL031 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20191023130455.1347-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Having the RAM creation code in a separate function is not
very helpful. Move this code directly inside the board_init()
function, this will later allow the board to have the QOM
ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the OMAP310 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the OMAP2420 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the SA1110 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-4-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exynos SoC has specific SDHCI registers. Use the s3c SDHCI
model which handle these specific registers.
This silents the following "SDHC ... not implemented" warnings so
we can focus on the important registers missing:
$ qemu-system-arm ... -d unimp \
-append "... root=/dev/mmcblk0 rootfstype=ext4 rw rootwait" \
-drive file=linux-build-test/rootfs/arm/rootfs-armv5.ext2,if=sd,format=raw
[...]
[ 25.744858] sdhci: Secure Digital Host Controller Interface driver
[ 25.745862] sdhci: Copyright(c) Pierre Ossman
[ 25.783188] s3c-sdhci 12530000.sdhci: clock source 2: mmc_busclk.2 (12000000 Hz)
SDHC rd_4b @0x80 not implemented
SDHC wr_4b @0x80 <- 0x00000020 not implemented
SDHC wr_4b @0x8c <- 0x00030000 not implemented
SDHC rd_4b @0x80 not implemented
SDHC wr_4b @0x80 <- 0xc0004100 not implemented
SDHC wr_4b @0x84 <- 0x80808080 not implemented
[ 26.013318] mmc0: SDHCI controller on samsung-hsmmc [12530000.sdhci] using ADMA
[ 26.032318] Synopsys Designware Multimedia Card Interface Driver
[ 42.024885] Waiting for root device /dev/mmcblk0...
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-id: 20191005154748.21718-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdpjPbAAoJECgfDbjSjVRpQqUH/2xyT++y8K17mCI1IILLZd3d
eOqElEHz78qlEfR2euv63YksZoeHpMO5HiAdwOGGF8CjcaCT4Hl+pPDffTYVXtt+
VZ88vSSXL49wpMcpvRGR5Isy0eXJzWilTBMu2eu8phN9tX82dlu08Oi4XGAosrBJ
uZg61DyiGDnSOpoofHhjvXJEaiL0pzkTjf8qAoW3TaVcB9NQKnunMEIDD646JS5z
AAj4+XBJfUG9cp7/MG+djjVmJDdUpjL5e5uWNWakbgUVqSbHog78RIrBoD6SH7pt
/6hHHoSM9VX1wWgdTdVdNAQAZVnWs31w4v31d8UfaT15KJEoG47U0gDgmLzXDyo=
=+xdg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, acpi: features, fixes, tests
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2019 22:02:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: add vhost-user-fs-pci device
virtio: add vhost-user-fs base device
virtio: Add virtio_fs linux headers
tests/acpi: add expected tables for arm/virt
tests: document how to update acpi tables
tests: Add bios tests to arm/virt
tests: allow empty expected files
tests/acpi: add empty files
tests: Update ACPI tables list for upcoming arm/virt tests
docs/specs: Add ACPI GED documentation
hw/arm: Use GED for system_powerdown event
hw/arm: Factor out powerdown notifier from GPIO
hw/arm/virt-acpi-build: Add PC-DIMM in SRAT
hw/arm/virt: Enable device memory cold/hot plug with ACPI boot
hw/arm/virt: Add memory hotplug framework
hw/acpi: Add ACPI Generic Event Device Support
hw/acpi: Do not create memory hotplug method when handler is not defined
hw/acpi: Make ACPI IO address space configurable
vhost-user: save features if the char dev is closed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Base addresses and sizes taken from the "BCM2835 ARM Peripherals"
datasheet from February 06 2012:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The UART1 is part of the AUX peripheral,
the PCM_CLOCK (yet unimplemented) is part of the CPRMAN.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IEC binary prefixes ease code review: the unit is explicit.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-id: 20190926173428.10713-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-24-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 SoC has an extra controller to set the PHY registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-23-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To support the ast2600's four MACs allow SoCs to specify the number
they have, and create that many.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-22-clg@kaod.org
[clg: - included a check on sc->macs_num when realizing the macs
- included interrupt definitions for the AST2600 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial definitions for a simple machine using an AST2600 SoC (Cortex
CPU).
The Cortex CPU and its interrupt controller are too complex to handle
in the common Aspeed SoC framework. We introduce a new Aspeed SoC
class with instance_init and realize handlers to handle the differences
with the AST2400 and the AST2500 SoCs. This will add extra work to
keep in sync both models with future extensions but it makes the code
clearer.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-19-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for the AST2600.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for register differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-16-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It cleanups the current models for the Aspeed AST2400 and AST2500 SoCs
and prepares ground for future SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-11-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use class handlers and class constants to differentiate the
characteristics of the memory controller and remove the 'silicon_rev'
property.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The most important changes will be on the register range 0x34 - 0x3C
memops. Introduce class read/write operations to handle the
differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the musicpal code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-6-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
For machines 4.2 or higher with ACPI boot use GED for system_powerdown
event instead of GPIO. Guest boot with DT still uses GPIO.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-9-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is in preparation of using GED device for
system_powerdown event. Make the powerdown notifier
registration independent of create_gpio() fn.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-8-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Generate Memory Affinity Structures for PC-DIMM ranges.
Also, Linux and Windows need ACPI SRAT table to make memory hotplug
work properly, however currently QEMU doesn't create SRAT table if
numa options aren't present on CLI. Hence add support(>=4.2) to
create numa node automatically (auto_enable_numa_with_memhp) when
QEMU is started with memory hotplug enabled but without '-numa'
options on CLI.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-7-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This initializes the GED device with base memory and irq, configures
ged memory hotplug event and builds the corresponding aml code. With
this, both hot and cold plug of device memory is enabled now for Guest
with ACPI boot. Memory cold plug support with Guest DT boot is not yet
supported.
As DSDT table gets changed by this, update bios-tables-test-allowed-diff.h
to avoid "make check" failure.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-Id: <20190918130633.4872-6-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
This patch adds the memory hot-plug/hot-unplug infrastructure
in machvirt. The device memory is not yet exposed to the Guest
either through DT or ACPI and hence both cold/hot plug of memory
is explicitly disabled for now.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-5-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, when a notifier is attempted to be registered and its
flags are not supported (especially the MAP one) by the IOMMU MR,
we generally abruptly exit in the IOMMU code. The failure could be
handled more nicely in the caller and especially in the VFIO code.
So let's allow memory_region_register_iommu_notifier() to fail as
well as notify_flag_changed() callback.
All sites implementing the callback are updated. This patch does
not yet remove the exit(1) in the amd_iommu code.
in SMMUv3 we turn the warning message into an error message saying
that the assigned device would not work properly.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190923131108.21459-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're booting a Linux kernel directly into Non-Secure
state on a CPU which has Secure state, then make sure we
set the NSACR CP11 and CP10 bits, so that Non-Secure is allowed
to access the FPU. Otherwise an AArch32 kernel will UNDEF as
soon as it tries to use the FPU.
It used to not matter that we didn't do this until commit
fc1120a7f5, where we implemented actually honouring
these NSACR bits.
The problem only exists for CPUs where EL3 is AArch32; the
equivalent AArch64 trap bits are in CPTR_EL3 and are "0 to
not trap, 1 to trap", so the reset value of the register
permits NS access, unlike NSACR.
Fixes: fc1120a7f5
Fixes: https://bugs.launchpad.net/qemu/+bug/1844597
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190920174039.3916-1-peter.maydell@linaro.org
and use a class AspeedSCUClass to define each SoC characteristics.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-10-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.
The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are no QEMU Aspeed machines using the SoCs "ast2400-a0" or
"ast2400".
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-4-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
-----BEGIN PGP SIGNATURE-----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=u5HZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine + x86 queue, 2019-09-03
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
# gpg: Signature made Tue 03 Sep 2019 21:57:37 BST
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
migration: Do not re-read the clock on pre_save in case of paused guest
x86: do not advertise die-id in query-hotpluggbale-cpus if '-smp dies' is not set
i386/vmmouse: Properly reset state
hostmem-file: fix pmem file size check
qapi: report the default CPU type for each machine
pc: Don't make die-id mandatory unless necessary
pc: Improve error message when die-id is omitted
pc: Fix error message on die-id validation
numa: move numa global variable numa_info into MachineState
numa: move numa global variable have_numa_distance into MachineState
numa: move numa global variable nb_numa_nodes into MachineState
hw/arm: simplify arm_load_dtb
includes: remove stale [smp|max]_cpus externs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Child properties form the composition tree. All objects need to be
a child of another object. Objects can only be a child of one object.
Respect this with the i.MX SoC, to get a cleaner composition tree.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both object_initialize() and qdev_set_parent_bus() increase the
reference counter of the new object, so one of the references has
to be dropped afterwards to get the reference counting right.
In machine model code this refcount leak is not particularly
problematic because (unlike devices) machines will never be
created on demand via QMP, and they are never destroyed.
But in any case let's use the new sysbus_init_child_obj() instead
to get the reference counting here right.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-4-philmd@redhat.com
[PMM: rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit ba1ba5cca introduce the ARM_CPU_TYPE_NAME() macro.
Unify the code base by use it in all places.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190823143249.8096-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An IOVA/ASID invalidation is notified to all IOMMU Memory Regions
through smmuv3_inv_notifiers_iova/smmuv3_notify_iova.
When the notification occurs it is possible that some of the
PCIe devices associated to the notified regions do not have a
valid stream table entry. In that case we output a LOG_GUEST_ERROR
message, for example:
invalid sid=<SID> (L1STD span=0)
"smmuv3_notify_iova error decoding the configuration for iommu mr=<MR>
This is unfortunate as the user gets the impression that there
are some translation decoding errors whereas there are not.
This patch adds a new field in SMMUEventInfo that tells whether
the detection of an invalid STE must lead to an error report.
invalid_ste_allowed is set before doing the invalidations and
kept unset on actual translation.
The other configuration decoding error messages are kept since if the
STE is valid then the rest of the config must be correct.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190822172350.12008-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Log a guest error when encountering an invalid STE.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190822172350.12008-5-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move existing numa global have_numa_distance into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-4-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In struct arm_boot_info, kernel_filename, initrd_filename and
kernel_cmdline are copied from from MachineState. This patch add
MachineState as a parameter into arm_load_dtb() and move the copy chunk
of kernel_filename, initrd_filename and kernel_cmdline into
arm_load_kernel().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-2-tao3.xu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
Add 4.2 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1, as 0788a56bd1 ("i386: Make unversioned CPU models be
aliases") states this should only transition to the latest cpu
model version in 4.3 (or later).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190724103524.20916-1-cohuck@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The device is only used by some few boards. Let's use a proper Kconfig
switch so that we only compile this code if we really need it.
Message-Id: <20190817101931.28386-8-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "split-irq" device is currently only used by machines that use
CONFIG_ARMSSE. Let's add a proper CONFIG_SPLIT_IRQ switch for this
so that it only gets compiled when we really need it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190817101931.28386-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "or-irq" device is only used by certain machines. Let's add
a proper config switch for it so that it only gets compiled when we
really need it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190817101931.28386-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
hw/boards.h pulls in almost 60 headers. The less we include it into
headers, the better. As a first step, drop superfluous inclusions,
and downgrade some more to what's actually needed. Gets rid of just
one inclusion into a header.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
According to hw/ide/internal's file comment, only files in hw/ide/ are
supposed to include it. Drag reality slightly closer to supposition.
Three includes outside hw/ide remain: hw/arm/sbsa-ref.c,
include/hw/ide/pci.h, and include/hw/misc/macio/macio.h. Turns out
board code needs ide-internal.h to wire up IDE stuff. More cleanup is
needed. Left for another day.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-11-armbru@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
In commit e6b2b20d97 we made the boot loader code try to avoid
putting the initrd on top of the kernel. However the expression used
to calculate the start of the initrd:
info->initrd_start = info->loader_start +
MAX(MIN(info->ram_size / 2, 128 * 1024 * 1024), kernel_size);
incorrectly uses 'kernel_size' as the offset within RAM of the
highest address to avoid. This is incorrect because the kernel
doesn't start at address 0, but slightly higher than that. This
means that we can still incorrectly end up overlaying the initrd on
the kernel in some cases, for example:
* The kernel's image_size is 0x0a7a8000
* The kernel was loaded at 0x40080000
* The end of the kernel is 0x4A828000
* The DTB was loaded at 0x4a800000
To get this right we need to track the actual highest address used
by the kernel and use that rather than kernel_size. We already
set image_low_addr and image_high_addr for ELF images; set them
also for the various other image types we support, and then use
image_high_addr as the lowest allowed address for the initrd.
(We don't use image_low_addr, but we set it for consistency
with the existing code path for ELF files.)
Fixes: e6b2b20d97
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190722151804.25467-3-peter.maydell@linaro.org
Rename the elf_low_addr and elf_high_addr variables to image_low_addr
and image_high_addr -- in the next commit we will extend them to
be set for other kinds of image file and not just ELF files.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190722151804.25467-2-peter.maydell@linaro.org
The i.MX6UL always has a single Cortex-A7 CPU (we set FSL_IMX6UL_NUM_CPUS
to 1 in line with this). This means that all the code in fsl-imx6ul.c to
handle multiple CPUs is dead code, and Coverity is now complaining that
it is unreachable (CID 1403008, 1403011).
Remove the unreachable code and the only-executes-once loops,
and replace the single-entry cpu[] array in the FSLIMX6ULState
with a simple cpu member.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190712115030.26895-1-peter.maydell@linaro.org
Using the whole 128 MiB flash in non-secure mode is not working because
virt_flash_fdt() expects the same address for secure_sysmem and sysmem.
This is not correctly handled by caller because it forwards NULL for
secure_sysmem in non-secure flash mode.
Fixed by using sysmem when secure_sysmem is NULL.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Message-id: 20190712075002.14326-1-david.engraf@sysgo.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the virt machine, we support TrustZone being either present or
absent, and so the code must deal with the secure_sysmem pointer
possibly being NULL. In the sbsa-ref machine, TrustZone is always
present, but some code and comments copied from virt still treat
it as possibly not being present.
This causes Coverity to complain (CID 1407287) that we check
secure_sysmem for being NULL after an unconditional dereference.
Simplify the code so that instead of initializing the variable
to NULL, unconditionally assigning it, and then testing it for NULL,
we just initialize it correctly in the variable declaration and
then assume it to be non-NULL. We also delete a comment which
only applied to the non-TrustZone config.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190704142004.7150-1-peter.maydell@linaro.org
Tested-by: Radosław Biernacki <radoslaw.biernacki@linaro.org>
Reviewed-by: Radosław Biernacki <radoslaw.biernacki@linaro.org>
Legacy '-numa node,mem' option has a number of issues and mgmt often
defaults to it. Unfortunately it's no possible to replace it with
an alternative '-numa memdev' without breaking migration compatibility.
What's possible though is to deprecate it, keeping option working with
old machine types only.
In order to help users to find out if being deprecated CLI option
'-numa node,mem' is still supported by particular machine type, add new
"numa-mem-supported" property to output of query-machines.
"numa-mem-supported" is set to 'true' for machines that currently support
NUMA, but it will be flipped to 'false' later on, once deprecation period
expires and kept 'true' only for old machine types that used to support
the legacy option so it won't break existing configuration that are using
it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1560172207-378962-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global smp variables in arm are replaced with smp machine properties.
The init_cpus() and *_create_rpu() are refactored to pass MachineState.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-9-like.xu@linux.intel.com>
[ehabkost: Fix hw/arm/sbsa-ref.c and hw/arm/aspeed.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Following the previous patch, this patch adds peripheral devices to the
newly introduced SBSA-ref machine.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1561890034-15921-3-git-send-email-hongbo.zhang@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For AArch64, the existing "virt" machine is primarily meant to
run on KVM and execute virtualization workloads, but we need an
environment as faithful as possible to physical hardware, for supporting
firmware and OS development for physical Aarch64 machines.
This patch introduces new machine type 'sbsa-ref' with main features:
- Based on 'virt' machine type.
- A new memory map.
- CPU type cortex-a57.
- EL2 and EL3 are enabled.
- GIC version 3.
- System bus AHCI controller.
- System bus EHCI controller.
- CDROM and hard disc on AHCI bus.
- E1000E ethernet card on PCIE bus.
- VGA display adaptor on PCIE bus.
- No virtio devices.
- No fw_cfg device.
- No ACPI table supplied.
- Only minimal device tree nodes.
Arm Trusted Firmware and UEFI porting to this are done accordingly,
and the firmware should supply ACPI tables to the guest OS. The
minimal device tree nodes supplied by QEMU for this platform are only
to pass the dynamic info reflecting command line input to firmware,
not for loading the guest OS.
To make the review easier, this task is split into two patches, the
fundamental skeleton part and the peripheral devices part; this patch is
the first part.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1561890034-15921-2-git-send-email-hongbo.zhang@linaro.org
[PMM: commit message tweaks; moved some bits between patch 1 and 2
to ensure patch 1 builds cleanly; removed unneeded lines from
Kconfig stanza; only provide board for qemu-system-aarch64, not
qemu-system-arm; added MAINTAINERS entry]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ast2500 uses the watchdog to reset the SDRAM controller. This
operation is usually performed by u-boot's memory training procedure,
and it is enabled by setting a bit in the SCU and then causing the
watchdog to expire. Therefore, we need the watchdog to be able to
access the SCU's register space.
This causes the watchdog to not perform a system reset when the bit is
set. In the future it could perform a reset of the SDMC model.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190621065242.32535-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XDMA engine embedded in the Aspeed SOCs performs PCI DMA operations
between the SOC (acting as a BMC) and a host processor in a server.
The XDMA engine exists on the AST2400, AST2500, and AST2600 SOCs, so
enable it for all of those. Add trace events on the important register
writes in the XDMA engine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-21-clg@kaod.org
[clg: - changed title ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Swift board is an OpenPOWER system hosting POWER processors.
Add support for their BMC including the I2C devices as found on HW.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-20-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DRAM address of a DMA transaction depends on the DRAM base address
of the SoC. Inform the SMC controller model with this value.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618165311.27066-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RAM memory region is defined after the SoC is realized when the
SDMC controller has checked that the defined RAM size for the machine
is correct. This is problematic for controller models requiring a link
on the RAM region, for DMA support in the SMC controller for instance.
Introduce a container memory region for the RAM that we can link into
the controllers early, before the SoC is realized. It will be
populated with the RAM region after the checks have be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It has never been used as far as I can tell from the git history.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-13-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoCs have two MACs. Extend the Aspeed model to support a
second NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current models of the Aspeed SoCs only have one CPU but future
ones will support SMP. Introduce a new num_cpus field at the SoC class
level to define the number of available CPUs per SoC and also
introduce a 'num-cpus' property to activate the CPUs configured for
the machine.
The max_cpus limit of the machine should depend on the SoC definition
but, unfortunately, these values are not available when the machine
class is initialized. This is the reason why we add a check on
num_cpus in the AspeedSoC realize handler.
SMP support will be activated when models for such SoCs are implemented.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All systems have an RTC.
The IRQ is hooked up but the model does not use it at this stage. There
is no guest code that uses it, so this limitation is acceptable.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a slightly different address space and have a different set
of controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a different CPU and a different IRQ number layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add no-op/unimplemented PCIE PHY IP block. Needed by new kernels to
use PCIE.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow cortex-a7 to be used with the virt board; it supports
the v7VE features and there is no reason to deny this type.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: fc5404f7-4d1d-c28f-6e48-d8799c82acc0@web.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This machine correctly defines its default_cpu_type to cortex-m3
and report an error if the user requested another cpu_type,
however it does not exit, and this can confuse users trying
to use another core:
$ qemu-system-arm -M emcraft-sf2 -cpu cortex-m4 -kernel test-m4.elf
qemu-system-arm: This board can only be used with CPU cortex-m3-arm-cpu
[output related to M3 core ...]
The CPU is indeed a M3 core:
(qemu) info qom-tree
/machine (emcraft-sf2-machine)
/unattached (container)
/device[0] (msf2-soc)
/armv7m (armv7m)
/cpu (cortex-m3-arm-cpu)
Add the missing exit() call to return to the shell.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20190617160136.29930-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the condition used to check whether the initrd fits
into RAM; in some cases if an initrd was also passed on
the command line we would get an error stating that it
was too big to fit into RAM after the kernel. Despite the
error the loader continued anyway, though, so also add an
exit(1) when the initrd is actually too big.
Fixes: 852dc64d66 ("hw/arm/boot: Diagnose layouts that put initrd or
DTB off the end of RAM")
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190618125844.4863-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-200 hardware has configurable integration settings which
determine whether its two CPUs have the FPU and DSP:
* CPU0_FPU (default 0)
* CPU0_DSP (default 0)
* CPU1_FPU (default 1)
* CPU1_DSP (default 1)
Similarly, the IoTKit has settings for its single CPU:
* CPU0_FPU (default 1)
* CPU0_DSP (default 1)
Of our four boards that use either the IoTKit or the SSE-200:
* mps2-an505, mps2-an521 and musca-a use the default settings
* musca-b1 enables FPU and DSP on both CPUs
Currently QEMU models all these boards using CPUs with
both FPU and DSP enabled. This means that we are incorrect
for mps2-an521 and musca-a, which should not have FPU or DSP
on CPU0.
Create QOM properties on the ARMSSE devices corresponding to the
default h/w integration settings, and make the Musca-B1 board
enable FPU and DSP on both CPUs. This fixes the mps2-an521
and musca-a behaviour, and leaves the musca-b1 and mps2-an505
behaviour unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-5-peter.maydell@linaro.org
Create "vfp" and "dsp" properties on the armv7m container object
which will be forwarded to its CPU object, so that SoCs can
configure whether the CPU has these features.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-4-peter.maydell@linaro.org
Since Linux v3.17, the kernel's Image header includes a field image_size,
which gives the total size of the kernel including unpopulated data
sections such as the BSS). If this is present, then return it from
load_aarch64_image() as the true size of the kernel rather than
just using the size of the Image file itself. This allows the code
which calculates where to put the initrd to avoid putting it in
the kernel's BSS area.
This means that we should be able to reliably load kernel images
which are larger than 128MB without accidentally putting the
initrd or dtb in locations that clash with the kernel itself.
Fixes: https://bugs.launchpad.net/qemu/+bug/1823998
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-5-peter.maydell@linaro.org
We currently put the initrd at the smaller of:
* 128MB into RAM
* halfway into the RAM
(with the dtb following it).
However for large kernels this might mean that the kernel
overlaps the initrd. For some kinds of kernel (self-decompressing
32-bit kernels, and ELF images with a BSS section at the end)
we don't know the exact size, but even there we have a
minimum size. Put the initrd at least further into RAM than
that. For image formats that can give us an exact kernel size, this
will mean that we definitely avoid overlaying kernel and initrd.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-4-peter.maydell@linaro.org
We calculate the locations in memory where we want to put the
initrd and the DTB based on the size of the kernel, since they
come after it. Add some explicit checks that these aren't off the
end of RAM entirely.
(At the moment the way we calculate the initrd_start means that
it can't ever be off the end of RAM, but that will change with
the next commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-3-peter.maydell@linaro.org
In the Arm kernel/initrd loading code, in some places we make the
incorrect assumption that info->ram_size can be treated as the
address of the end of RAM, as for instance when we calculate the
available space for the initrd using "info->ram_size - info->initrd_start".
This is wrong, because many Arm boards (including "virt") specify
a non-zero info->loader_start to indicate that their RAM area
starts at a non-zero physical address.
Correct the places which make this incorrect assumption.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-2-peter.maydell@linaro.org
arm and i386 has almost the same function acpi_add_rom_blob(), except
giving different FWCfgCallback function.
This patch moves acpi_add_rom_blob() to utils.c by passing
FWCfgCallback to it.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v7:
* rebase on top of current master because of conflict
v6:
* change author from Igor to Michael
v5:
* remove unnecessary header glib/gprintf.h
* rearrange include header to make it more suitable
v4:
* extract -> moves
* adjust comment in source to make checkpatch happy
v3:
* put acpi_add_rom_blob() to hw/acpi/utils.c
v2:
* remove unused header in original source file
Message-Id: <20190610011830.28398-1-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The SMMUv3 ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190524124829.2589-1-peter.maydell@linaro.org
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJc+B4YAAoJECgfDbjSjVRpq1EIAJR7tCxcpu9GggVlinmUA8G4
tmSAe06IryH7+nF3RsnINuGu7ius9qC2/E2y0uJUHhTqiU/RWOfWZ7PPM0EcYZaA
TLPaCe2NUF6/8afeqmvE9Usk7VspI5TDZRms+bonmZz2xP1lHIMN0qW4s7HHLWr8
sZKDtCJ+9cYII93VQwtlR0qiHgv5f0kzcuZeJaZHsAHH6XZGqRuQjI6txcFa4o53
lkdLCEwTnRuwu2wyL84eL5p+E8SzOgR/x1QI+nffrJfsvnmiT7lnOrkjnQlWAp5G
xqwqsUrUxUCuQ+zitwJqmv+H6nx79MwAM7fTHAETCWX703N5o9tZxAnHHqLoa8I=
=cQNg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, pci, pc: cleanups, features
stricter rules for acpi tables: we now fail
on any difference that isn't whitelisted.
vhost-scsi migration.
some cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 05 Jun 2019 20:55:04 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
bios-tables-test: ignore identical binaries
tests: acpi: add simple arm/virt testcase
tests: add expected ACPI tables for arm/virt board
bios-tables-test: list all tables that differ
vhost-scsi: Allow user to enable migration
vhost-scsi: Add VMState descriptor
vhost-scsi: The vhost backend should be stopped when the VM is not running
bios-tables-test: add diff allowed list
vhost: fix memory leak in vhost_user_scsi_realize
vhost: fix incorrect print type
vhost: remove the dead code
docs: smbios: remove family=x from type2 entry description
pci: Fold pci_get_bus_devfn() into its sole caller
pci: Make is_bridge a bool
pcie: Simplify pci_adjust_config_limit()
acpi: pci: use build_append_foo() API to construct MCFG
hw/acpi: Consolidate build_mcfg to pci.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no need to have a test device created by the board.
Instead, create it in the qtest so that we will be able to run
it on other boards too.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script:
@use_sysbus_init_child_obj_missing_parent@
expression child_ptr;
expression child_type;
expression child_size;
@@
- object_initialize(child_ptr, child_size, child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
...
?- object_unref(OBJECT(child_ptr));
+ sysbus_init_child_obj(OBJECT(PARENT_OBJ), "CHILD_NAME", child_ptr,
+ child_size, child_type);
We let the MPS2 boards adopt the cpu core, the FPGA and the SCC children.
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-16-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
@use_sysbus_init_child_obj@
expression parent_obj;
expression dev;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
|
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
- dev = DEVICE(child_ptr);
- qdev_set_parent_bus(dev, sysbus_get_default());
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-9-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
@use_sysbus_init_child_obj@
expression parent_obj;
expression dev;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
|
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
- dev = DEVICE(child_ptr);
- qdev_set_parent_bus(dev, sysbus_get_default());
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20190507163416.24647-8-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As explained in commit aff39be0ed:
Both functions, object_initialize() and object_property_add_child()
increase the reference counter of the new object, so one of the
references has to be dropped afterwards to get the reference
counting right. Otherwise the child object will not be properly
cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the
reference counting here right.
This patch was generated using the following Coccinelle script
(with a bit of manual fix-up for overly long lines):
@use_object_initialize_child@
expression parent_obj;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, &error_abort, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), NULL);
...
?- object_unref(OBJECT(child_ptr));
|
- object_initialize(child_ptr, child_size, child_type);
+ object_initialize_child(parent_obj, child_name, child_ptr, child_size,
+ child_type, errp, NULL);
... when != parent_obj
- object_property_add_child(parent_obj, child_name, OBJECT(child_ptr), errp);
...
?- object_unref(OBJECT(child_ptr));
)
@use_sysbus_init_child_obj@
expression parent_obj;
expression dev;
expression child_ptr;
expression child_name;
expression child_type;
expression child_size;
expression errp;
@@
(
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
...
- qdev_set_parent_bus(DEVICE(child_ptr), sysbus_get_default());
|
- object_initialize_child(parent_obj, child_name, child_ptr, child_size,
- child_type, errp, NULL);
+ sysbus_init_child_obj(parent_obj, child_name, child_ptr, child_size,
+ child_type);
- dev = DEVICE(child_ptr);
- qdev_set_parent_bus(dev, sysbus_get_default());
)
While the object_initialize() function doesn't take an
'Error *errp' argument, the object_initialize_child() does.
Since this code is used when a machine is created (and is not
yet running), we deliberately choose to use the &error_abort
argument instead of ignoring errors if an object creation failed.
This choice also matches when using sysbus_init_child_obj(),
since its code is:
void sysbus_init_child_obj(Object *parent,
const char *childname, void *child,
size_t childsize, const char *childtype)
{
object_initialize_child(parent, childname, child, childsize,
childtype, &error_abort, NULL);
qdev_set_parent_bus(DEVICE(child), sysbus_get_default());
}
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-7-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To be coherent with the other peripherals contained in the
BCM2835PeripheralState structure, directly allocate the PL011State
(instead of using the pl011 uart as a pointer to a SysBusDevice).
Initialize the PL011State with object_initialize() instead of
object_new().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-6-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It eases code review, unit is explicit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-3-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
To build MCFG, two information is necessary:
* bus number
* base address
Abstract these two information to AcpiMcfgInfo so that build_mcfg and
build_mcfg_q35 will have the same declaration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190419003053.8260-5-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
mcfg_start points to the start of MCFG table and is used in
build_header. While this information could be derived from mcfg.
This patch removes the unnecessary variable mcfg_start.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190419003053.8260-3-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=wO8o
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2019-05-13' into staging
Kconfig settings for the Arm machines
# gpg: Signature made Mon 13 May 2019 09:19:43 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2019-05-13: (29 commits)
hw/arm: Remove hard-enablement of the remaining PCI devices
hw/arm: Express dependencies of the musca machines with Kconfig
hw/arm: Express dependencies of the xlnx-versal-virt machine with Kconfig
hw/arm: Express dependencies of the ZynqMP zcu102 machine with Kconfig
hw/arm: Express dependencies of the microbit / nrf51 machine with Kconfig
hw/arm: Express dependencies of the remaining IMX boards with Kconfig
hw/arm: Express dependencies of the MSF2 / EMCRAFT_SF2 machine with Kconfig
hw/arm: Express dependencies of sabrelite with Kconfig
hw/arm: Express dependencies of canon-a1100 with Kconfig
hw/arm: Express dependencies of the raspi machines with Kconfig
hw/arm: Express dependencies of the MPS2 boards with Kconfig
hw/arm: Express dependencies of allwinner / cubieboard with Kconfig
hw/arm: Express dependencies of netduino / stm32f2xx with Kconfig
hw/arm: Express dependencies of the virt machine with Kconfig
hw/arm: Express dependencies of the aspeed boards with Kconfig
hw/arm: Express dependencies of collie with Kconfig
hw/arm: Express dependencies of xilinx-zynq with Kconfig
hw/arm: Express dependencies of the PXA2xx machines with Kconfig
hw/arm: Express dependencies of realview, versatile and vexpress with Kconfig
hw/arm: Express dependencies of stellaris with Kconfig
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Dependencies have been determined with trial-and-error and by
looking at the musca.c source file.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined with trial-and-error and by
looking at the xlnx-versal.c source file.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This cleans up most settings in default-configs/aarch64-softmmu.mak.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the NRF51 / microbit machine.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
IMX25, IMX7 and IMX6UL were still missing the Kconfig dependencies.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the emcraft-sf2 machine - we also
distinguish between the machine (CONFIG_EMCRAFT_SF2) and the SoC
(CONFIG_MSF2) now.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the Sabrelite / iMX6 machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the DIGIC / canon-a1100 machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Most of the code is directly controlled by the CONFIG_RASPI switch,
so not much to add here additionally.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the mps2-an* machines.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add dependencies for the Cubitech Cubieboard.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Netduino only depends on the stm32f205 SoC which in turn depends on
its components.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined by looking at hw/arm/virt.c
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined by looking at hw/arm/aspeed.c
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the Strongarm collie machine.
This patch is based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the xilinx-zynq-a9 board.
This patch is based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the PXA2xx machines (akita, borzoi,
connex and verdex gumstix, tosa, mainstone, spitz, terrier and z2).
This patch is based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the OMAP machines (cheetah, n800, n810,
sx1 and sx1-v1).
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the fsl-imx31 / kzm machine.
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the highbank machine (and the midway
machine).
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the Exynos-related boards (nuri and
smdkc210).
This patch is slightly based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Raspberry Pi boards have a physical memory map which does
not allow for more than 1GB of RAM. Currently if the user tries
to ask for more then we fail in a confusing way:
$ qemu-system-aarch64 --machine raspi3 -m 8G
Unexpected error in visit_type_uintN() at qapi/qapi-visit-core.c:164:
qemu-system-aarch64: Parameter 'vcram-base' expects uint32_t
Aborted (core dumped)
Catch this earlier and diagnose it with a more friendly message:
$ qemu-system-aarch64 --machine raspi3 -m 8G
qemu-system-aarch64: Requested ram size is too large for this machine: maximum is 1GB
Fixes: https://bugs.launchpad.net/qemu/+bug/1794187
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit finally deletes "hw/devices.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-13-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-12-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-10-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since uWireSlave is only used in this new header, there is no
need to expose it via "qemu/typedefs.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-9-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-8-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-7-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an entries the Blizzard device in MAINTAINERS.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-3-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is more proper to use PCIE_MMCFG_BUS to retrieve end_bus_number.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190312074953.16671-1-richardw.yang@linux.intel.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GSIV numbers of the SPI based interrupts is not correct as
ARM_SPI_BASE was not added to the irqmap[VIRT_SMMU] value. So
this may collide with VIRTIO_MMIO irq window.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20190312091031.5185-1-eric.auger@redhat.com
Reviewed-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
We have two open-coded copies of macro PFLASH_CFI01(). Move the macro
to the header, so we can ditch the copies. Move PFLASH_CFI02() to the
header for symmetry.
We define macros TYPE_PFLASH_CFI01 and TYPE_PFLASH_CFI02 for type name
strings, then mostly use the strings. If the macros are worth
defining, they are worth using. Replace the strings by the macros.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-6-armbru@redhat.com>
flash.h's incomplete struct pflash_t is completed both in
pflash_cfi01.c and in pflash_cfi02.c. The complete types are
incompatible. This can hide type errors, such as passing a pflash_t
created with pflash_cfi02_register() to pflash_cfi01_get_memory().
Furthermore, POSIX reserves typedef names ending with _t.
Rename the two structs to PFlashCFI01 and PFlashCFI02.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-2-armbru@redhat.com>
Since commit 578f3c7b08 ("arm: add fw_cfg to "virt" board",
2014-12-22), the machvirt_init() unconditionally creates the
fw_cfg object. Later, commit c30e15658b ("smbios: implement
smbios support for mach-virt", 2015-09-07) added a superfluous
null-check on it.
Remove this superfluous check.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190309181920.30553-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the watchdog timer for the stellaris boards.
This device is a close variant of the CMSDK APB watchdog
device, so we can model it by subclassing that device and
tweaking the behaviour of some of its registers.
Signed-off-by: Michel Heily <michelheily@gmail.com>
Reviewed-by: Peter Maydell <petser.maydell@linaro.org>
[PMM: rewrote commit message, fixed a few checkpatch nits,
added comment giving the URL of the spec for the Stellaris
variant of the watchdog device]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have the extended memory map (high IO regions beyond the
scalable RAM) and dynamic IPA range support at KVM/ARM level
we can bump the legacy 255GB initial RAM limit. The actual maximum
RAM size now depends on the physical CPU and host kernel, in
accelerated mode. In TCG mode, it depends on the VCPU
AA64MMFR0.PARANGE.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-11-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are about to allow the memory map to grow beyond 1TB and
potentially overshoot the VCPU AA64MMFR0.PARANGE.
In aarch64 mode and when highmem is set, let's check the VCPU
PA range is sufficient to address the highest GPA of the memory
map.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-10-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the machine class kvm_type() callback.
It returns the number of bits requested to implement the whole GPA
range including the RAM and IO regions located beyond.
The returned value is passed though the KVM_CREATE_VM ioctl and
this allows KVM to set the stage2 tables dynamically.
To compute the highest GPA used in the memory map, kvm_type()
must freeze the memory map by calling virt_set_memmap().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-9-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We introduce an helper to create a memory node.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190304101339.25970-2-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
-----BEGIN PGP SIGNATURE-----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=XTkI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/i2c-for-release-20190228' into staging
This has been out there long enough, I need to get this in.
This was changed a little bit since my post on Feb 20 (to which
there were no comments) due to changes I had to work around:
Change b296b664ab "smbus: Add a helper to generate SPD EEPROM
data" added a function to include/hw/i2c/smbus.h, which I had to move to
include/hw/smbus_eeprom.h.
There were some changes to hw/i2c/Makefile.objs that I had to fix up.
Beyond that, no changes.
Thanks,
-corey
# gpg: Signature made Thu 28 Feb 2019 18:05:49 GMT
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/i2c-for-release-20190228:
i2c: Verify that the count passed in to smbus_eeprom_init() is valid
i2c:smbus_eeprom: Add a reset function to smbus_eeprom
i2c:smbus_eeprom: Add vmstate handling to the smbus eeprom
i2c:smbus_eeprom: Add a size constant for the smbus_eeprom size
i2c:smbus_eeprom: Add normal type name and cast to smbus_eeprom.c
i2c:smbus_slave: Add an SMBus vmstate structure
i2c:pm_smbus: Fix state transfer
migration: Add a VMSTATE_BOOL_TEST() macro
i2c:pm_smbus: Fix pm_smbus handling of I2C block read
boards.h: Ignore migration for SMBus devices on older machines
i2c:smbus: Make white space in switch statements consistent
i2c:smbus_eeprom: Get rid of the quick command
i2c:smbus: Simplify read handling
i2c:smbus: Simplify write operation
i2c:smbus: Correct the working of quick commands
i2c: Don't check return value from i2c_recv()
arm:i2c: Don't mask return from i2c_recv()
i2c: have I2C receive operation return uint8_t
i2c: Split smbus into parts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the handling of init-svtor and cpuwait initial
values is split between armsse.c and iotkit-sysctl.c:
the code in armsse.c sets the initial state of the CPU
object by setting the init-svtor and start-powered-off
properties, but the iotkit-sysctl.c code has its own
code setting the reset values of its registers (which are
then used when updating the CPU when the guest makes
runtime changes).
Clean this up by making the armsse.c code set properties on the
iotkit-sysctl object to define the initial values of the
registers, so they always match the initial CPU state,
and update the comments in armsse.c accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-9-peter.maydell@linaro.org
The SYSCTL block in the SSE-200 has some extra registers that
are not present in the IoTKit version. Add these registers
(as reads-as-written stubs), enabled by a new QOM property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-7-peter.maydell@linaro.org
Create and connect the MHUs in the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-3-peter.maydell@linaro.org
It can't fail, and now that it returns a uint8_t a 0xff mask
is unnecessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
smbus.c and smbus.h had device side code, master side code, and
smbus.h has some smbus_eeprom.c definitions. Split them into
separate files.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The region 0x40010000 .. 0x4001ffff and its secure-only alias
at 0x50010000... are for per-CPU devices. We implement this by
giving each CPU its own container memory region, where the
per-CPU devices live. Unfortunately, the alias region which
makes devices mapped at 0x4... addresses also appear at 0x5...
is only implemented in the overall "all CPUs" container. The
effect of this bug is that the CPU_IDENTITY register block appears
only at 0x4001f000, but not at the 0x5001f000 alias where it should
also appear. Guests (like very recent Arm Trusted Firmware-M)
which try to access it at 0x5001f000 will crash.
Fix this by moving the handling for this alias from the "all CPUs"
container to the per-CPU container. (We leave the aliases for
0x1... and 0x3... in the overall container, because there are
no per-CPU devices there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190215180500.6906-1-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Wire up the two PL011 UARTs in the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the PL031 RTC for the Musca board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca board puts its SRAM and flash behind TrustZone
Memory Protection Controllers (MPCs). Each MPC sits between
the CPU and the RAM/flash, and also has a set of memory mapped
control registers. Wire up the MPCs, and the memory behind them.
For the moment we implement the flash as simple ROM, which
cannot be reprogrammed by the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Many of the devices on the Musca board live behind TrustZone
Peripheral Protection Controllers (PPCs); add models of the
PPCs, using a similar scheme to the MPS2 board models.
This commit wires up the PPCs with "unimplemented device"
stubs behind them in the correct places in the address map.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca-A and Musca-B1 development boards are based on the
SSE-200 subsystem for embedded. Implement an initial skeleton
model of these boards, which are similar but not identical.
This commit creates the board model with the SSE and the IRQ
splitters to wire IRQs up to its two CPUs. As yet there
are no devices and no memory: these will be added later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Coverity points out (CID 1398632, CID 1398650) that we
leak a couple of allocated strings in the error-exit
code path for setting up the MHUs in the ARMSSE.
Fix this bug by moving the allocate-and-free of each
string to be closer to the use, so we do the free before
doing the error-exit check.
Fixes: f8574705f6 ("hw/arm/armsse: Add unimplemented-device stubs for MHUs")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190215113707.24553-1-peter.maydell@linaro.org
In commit 91c1e9fcbd where we added dual-CPU support to
the ARMSSE, we set up the wiring of the expansion IRQs via nested
loops: the outer loop on 'i' loops for each CPU, and the inner loop
on 'j' loops for each interrupt. Fix a typo which meant we were
wiring every expansion IRQ line to external IRQ 0 on CPU 0 and
to external IRQ 1 on CPU 1.
Fixes: 91c1e9fcbd ("hw/arm/armsse: Support dual-CPU configuration")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This will be needed by vhost-user-test, when each test switches to
its own GMainLoop and GMainContext. Otherwise, for a reconnecting
socket the initial connection will happen on the default GMainContext,
and no one will be listening on it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190202110834.24880-1-pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The arm_boot_info struct has a skip_dtb_autoload flag: if this is
set to true by the board code then arm_load_kernel() will not
load the DTB itself, but will leave this for the board code to
do itself later. However, the check for this is done in a
code path which is only executed for the case where we load
a kernel image file. If we're taking the "boot via firmware"
code path then the flag isn't honoured and the DTB is never
loaded.
We didn't notice this because the only real user of "boot
via firmware" that cares about the DTB is the virt board
(for UEFI boot), and that always wants skip_dtb_autoload
anyway. But the SBSA reference board model we're planning to
add will want the flag to behave correctly.
Now we've refactored the arm_load_kernel() function, the
fix is simple: drop the early 'return' so we fall into
the same "load the DTB" code the boot-direct-kernel path uses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-6-peter.maydell@linaro.org
The code path for booting firmware doesn't set env->boot_info. At
first sight this looks odd, so add a comment saying why we don't.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-5-peter.maydell@linaro.org
Factor out the "boot via firmware" code path from arm_load_kernel()
into its own function.
This commit only moves code around; no semantic changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-4-peter.maydell@linaro.org
Factor out the "direct kernel boot" code path from arm_load_kernel()
into its own function; this function is getting long enough that
the code flow is a bit confusing.
This commit only moves code around; no semantic changes.
We leave the "load the dtb" code in arm_load_kernel() -- this
is currently only used by the "direct kernel boot" path, but
this is a bug which we will fix shortly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-3-peter.maydell@linaro.org
Fix the block comment style in arm_load_kernel() to QEMU's
current style preferences. This will allow us to do some
refactoring of this function without checkpatch complaining
about the code-motion patches.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190131112240.8395-2-peter.maydell@linaro.org
Make ARM virt code configurable and the new CONFIG_ARM_VIRT
definitions added to the default-configs/arm-softmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-8-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Until now, the set_pc logic was unclear, which raised questions about
whether it should be used directly, applying a value to PC or adding
additional checks, for example, set the Thumb bit in Arm cpu. Let's set
the set_pc logic for “Configure the PC, as was done in the ELF file”
and implement synchronize_with_tb hook for preserving PC to cpu_tb_exec.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190129121817.7109-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the MPS2 FPGA image described in Application Note
AN521. This is identical to the AN505 image, except that it uses
the SSE-200 rather than the IoTKit and so has two Cortex-M33 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-24-peter.maydell@linaro.org
In preparation for adding support for the AN521 MPS2 image, we need
to handle wiring up the MPS2 device interrupt lines to both CPUs in
the SSE-200, rather than just the one that the IoTKit has.
Abstract out a "connect to the IoTKit interrupt line" function
and make it connect to a splitter which feeds both sets of inputs
for the SSE-200 case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-23-peter.maydell@linaro.org
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
