for mips3 (and later) 'ld' and 'sd' instructions. These currently
only are properly implemented for the _MIPS_BSD_API_LP32 and
_MIPS_BSD_API_LP32_64CLEAN 'API's. They're pretty messy, but when you
need them, you really need them.
you do not save it and pass it along in rval the system will start
to fail running user programs. This finishes the suggestion by cgd to
not save some registers on syscall entry.
that the page being zero'd was not completed and that page zeroing
should be aborted. This may be used by machine-dependent code doing
slow page access to reduce the latency of running a process that has
become runnable while in the middle of doing a slow page zero.
in syscall() anymore. By defition, processor was in SR_INT_IE turn
on prior to have syscall exception. MIPS1 assembler hook arranges
to enable the bit for its own. MIPS3 does the same effect by
turning off EXL bit.
fact the direct mapped cache makes address alias effect.
- Just turn on processor master interrupt mask IEc (SR_INT_IE) bit prior
to call syscall() kernel entry point. IEp is always 1 in this case
by defition.
and data cache sizes). R4000 uses 2^(12+IC) and 2^(12+DC). IDT32364
uses 2^(9+IC) and 2^(9+DC).
abstract around the problem by making the base a parameter to the
MIPS3_CONFIG_CACHE_SIZE macro. we pass the base down from mips_vector_init
to mips3_vector_init and to mips3_ConfigCache (where it is used).
XXX: someone with an MIPS3_4100 should switch to this and get rid
of the ugly ifdefs in cpuregs.h
a whole 0.01us in lmbench lat_syscall null on our 250Mhz QED system.
$at is still saved just to be safe, although it looks like it does
not need to be. $v1 is used in syscall(), although I'm not sure why.
process's segtab, retiring 'pcb_segtab' field from 'struct pcb'.
This would be another MULTIPROCESSOR unfriendly and the necessity
might be eliminated when the way to hold PTE is redesigned.
it look at casual inspection like 1 nop is needed but play other tricks.
Still have reduced by 1 nop. Hopefully this covers the NEC 41[x]1. Could
not find info for those processors.
in the non-MULTIPROCESSOR case (LOCKDEBUG requires it). Scheduler
lock is held upon entry to mi_switch() and cpu_switch(), and
cpu_switch() releases the lock before returning.
Largely from Bill Sommerfeld, with some minor bug fixes and
machine-dependent code hacking from me.
- MB_LEN_MAX is increased to 32.
- To ensure binary compatibility for old executables
under multibyte locale, versioned setlocale is added.
- __mb_len_cur definision is added in setlocale.c
and enable it in stdlib.h .
It is also important for multibyte locale stuffs,
but I just forgot.
the _2way and mips3_FlushDCache(). This lets all mips3 cache ops accept
user virtual addresss w/o a tlb miss. Since this is now done in both
ICache flush routines, no need to do it in pmap.c. Fixed R4400
stability problems with setregs() cache flushing.
is illegal to flush on user addresses. In theory the race exists
on MIPS1, but it is rather unlikely in common use. I have
seen it with regress/sys/kern/sigtramp on a QED 5231 system.
Previously we jal to panic which never cleared the tlb fault, so if
on the course of shutdown (like a doshutdownhooks() callback) missed
K2, it would panic again. Fix by setting EPC to panic() and eret.
By default this is off, and only slightly changes the code to load SR when
a temp register is available. This can be used by the platform code to
handle slow to clear interrupts (our case) or to mask off any interrupt
any interrupt at run-time. This can be very useful for embedded platforms
that have less than desirable interrupt properties.
cgd