Make sure we turn on DTR and/or RTS as appropriate during open.
Rearrange close sequence so the tty is flushed before turning off interrupts.
Deal with `softcar' and the console device by silently asserting CLOCAL and
|HUPCL, as in com driver.
Do *not* fiddle with DTR when changing the line speed.
Make sure we update the tty's carrier status when CLOCAL or MDMBUF is changed.
Only change rr1 when we actually need to turn on or off TIE.
things happen if we are the console.
Restore to the prevoius value (not to hardwired 8N1) because this
could be set by the serial console initialization.
Closed PR kern/4373 (Dave Huang)
in the ISR (from the ISA "ed" driver's generic 8390 probe routine).
Also, add a big comment describing exactly what we're checking when
probing for the dp8390 (also lifted from the ISA "ed" driver).
The RST check should help weed-out non-matches before they get to the
fairly invasive memory check.
should creation/initialization of a mscp fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one mscp what we can grab, and continue to hobble along.
Also, fix the mscp freelist fencepost error, similar to aha.c and bha.c
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
shoud creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Adjust the number of ccbs allocated during initialization.
Every ccb could potentially lock 64k of memory for dma buffers if bounce
buffers are used. Instead of BHA_CCB_MAX ccbs using 2MByte, only
sc_link.openings ccbs per device are allocated. Thus we now use only
256KByte per device present.
(hannken)
Fix a couple of errors in bha_create_ccbs():
- Don't ever let the number of CCBs be creater than BHA_CCB_MAX.
- Fix a fencepost that caused the last CCB allocated to never be put
on the freelist.
(thorpej)
- at end of attach, explicitely select an existing drive. This fixes hangs
some users reported (such as the one reported in port-i386/4247).
- Some atapi cdrom drives (e.g. Nec 24x) don't enables their registers before
a controller reset is issued. The controller probe routine is changed as
follow: issue a controller reset. If fail, test atapi signature on slave.
If fail, wait 5s and retry a reset. If the second reset fail, return(0).
If the first reset succeed, test presence of a master drive:
atapi signature, and if this fail RO/RW registers test. If no master, test
atapi signature on slave. If no slave, return 0.
"A sequence step of 0 after a select with ATN can be a selection
timeout, or it can also indicate the target did not respond with
a message out phase. The latter will occur on very old SCSI
devices which do not respond to the ATN signal and go directly to
the command phase".
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
options RND_COM
in your kernel config file (along with the
pseudo-device rnd
line) to enable this. If results are positive, I will make this enabled
by default.
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
> revision 1.1.2.4
> date: 1997/10/15 01:01:57; author: enami; state: Exp; lines: +10 -8
> Use bus_space_write_1() directly instead of NIC_PUT(), since
> - same io port is accessed by bus_space_read_1() in the same function, and
> - can bypass sc_reg_map[].
The isa attachment code is in isa/lpt_isa.c now, which attaches to the
already created ic/lpt* files.
You don't need to change your config files, but you need to re-"config" if
using lpt at isa.
XXX The "lpt" device definition should be in sys/conf/files instead, but to
my knowledge, there are some ports which have private copies of lpt, and would
choke on that. No need to make people unhappy 7 days before release branching.
pseudo-device rnd # /dev/random and in-kernel generator
in config files.
o Add declaration to all architectures.
o Clean up copyright message in rnd.c, rnd.h, and rndpool.c to include
that this code is derived in part from Ted Tyso's linux code.
[1] add EN_ENIDMAFIX - the byte-aligner on the ENI version of the card
appears to lose under heavy load so avoid using it. see comment
in midway.c for full details.
note that the Adaptec version of the card works properly under
load.
detected by Kenjiro Cho <kjc@csl.sony.co.jp> [confirmed by chuck]
fix by chuck & kjc
[2] update some freebsd specific code [from kjc]
[3] for circular buffers: ensure there is always one free slot so
that we can easily tell the difference between a full and
empty list. re-structure a few loops to reflect this.
fixes a problem with mbufs being free'd while still in DMA,
and makes drive a bit more robust.
detected and fixed by kjc
* support chip clocks != COM_FREQ, by introducing sc_frequency (for the
mainline code) and adding a frequency parameter right after the rate
parameter to comcnattach() and com_kgdb_attach().
- Make com_isa and com_multi initialize sc_frequency to COM_FREQ.
- Make i386/machdep.c and alpha/dec_xxx.c call com*attach() with the freq.
parameter.
* supio_attach_args get two more fields: a sc_ipl and a sc_arg, both ints.
- com_supio uses the first for interupt establishment (all childs will, as
soon as they exist) and the 2nd for sc_frequency.
- drsupio passes sc_ipl alway as 5, and for the "com"s, sc_arg as 16*115200
- hyper will pass sc_ipl as 6, and sc_arg as 16 * 460800
be probed several times. This fixes the "ATAPI CD probed as wd drive" problem.
Thanks to Geoff Wing <mason@primenet.com.au> for testing this on his hardware.
I also made inclusion of LPRINTF() dependent solely on the symbol
LPTDEBUG, initialized lptdebug variable to 0 instead of 1, and
matched arguments to format strings in LPRINTF() calls.
looking what's the autoconfig do on strange harware, and ATAPI_DEBUG2 is
for debuging data transfers (and is really verbose once the machine has booted
from an IDE disk).
(currently only CD-ROM drives on i386). The sys/dev/scsipi system provides 2
busses to which devices can attach (scsibus and atapibus). This needed to
change some include files and structure names in the low level scsi drivers.
at the same time instead by using two different calls. This enables
it to check more easily if the combined mode is all right.
- Improve the error checking in audio.c.
- Add a new audio property, AUDIO_PROP_INDEPENDENT, show if the
play and record settings are independent.
- Fix some buglets in audio.c.
-put all early console / KGDB initialization into 1 exported function
(com_*_attach()) each, dont use global variables anymore
-use the passed tcflag_t for port settings instead of hardwiring 8N1
-at autoconfiguration attach time, decide if the attaching device is
already console / KGDB by comparing bus tag and base addr (cgd's wish)
-export a function "com_is_console()" for use by driver frontends for
this comparision
-delay setting of cn_tab->cn_dev until autoconfiguration attach
to get the minor number right
-delete unused comcnprobe() and comcninit()
-Separate KGDB port initialization and softc related stuff to allow
KGDB to be attached in early system startup, before autoconfiguration.
-Export the variables needed by md code to hand-craft bus tag/handle.
-Fix initialization to enable interrupt by line break.
-Call DDB/KGDB at line break (move DDB call from the softirq handler
to the hard handler because it should work without a tty attached too).
mycroft