- "out of resource" errors cause receive buffer chain corruption
- resets can confuse the interrupt handler
- multi-cast setup causes receive buffer chain corruption
- shared memory setup incomplete
* Enhance effiency by avoiding unnecessary shared memory access,
improved handling of receive frame & buffer descriptors, and
introducing an `asynchronous' option when issuing 82586 commands.
* Exclusively use offsets relative to the bus handle representing the shared
memory area to formulate accesses to the chip's data-structures. The
front-ends provide glue functions that cater to the chip's endian-
sensitivity, to perform the actual device access (note: single-byte
accesses are done here using `bus_space_{read,write}_1()').
This concludes the transformation into a bus-independent driver module.
* Abolish C structures to access chip data-structures; instead use macros
that take indices and offsets relative to the bus handle representing
the chip's resources.
* Include the old version of this file wholesale, until all drivers
have been updated to use the MI 82586 code.
- allow get/set of enums SUNAUDIO_SOURCE and SUNAUDIO_OUTPUT rather
than returning EINVAL
- add missing SUNAUDIO_MONITOR_CLASS case in query_devinfo
- convert SUNAUDIO_MONITOR case from a MIXER_CLASS to a MIXER_VALUE
like it is supposed to be
- the labels for outputs/record class were swapped: fix it
this patch allows "mixerctl" to work properly on a sparc
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
* Carrier detect (TS_CARR_ON) is based on the actual DCD bit, even if it's
being ignored.
* Set TS_WOPEN early on in zsopen().
* Don't disable interrupts on the console during close if we have DDB.
Inert changes:
* Don't handle ZS_HWFLAG_NO_DCD here; the frontend does it.
* Deprecate `register'.
* Use SET(), CLR(), and ISSET().
More performance changes:
* Rototill receive handling; use a backpressure mechanism to prevent livelock.
* Output silo/ibuf overflow warnings at most once per minute, from a callout.
* When we exhaust the current transmit run, turn off transmit interrupts in
zstty_txint(), so we're fairly sure we don't get another one.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
control any more, and the speed of changing DTR isn't really an issue. Also,
the old code created a bug where zsparam() might have failed to set some
registers.
Change the interface to zs_hwiflow(); just have it use zst_rx_blocked.
Make zs_modem() a tiny bit faster.
Do RTS updates immediately; do not allow them to be held.
Stop output as fast as possible when DCD is deasserted.
Do *not* automatically drop DTR when DCD is deasserted.
Only check for rr0 bits that we care about (DTR and DCD).
enami