This patch adds minimal support for AXP-209 PMU.
Most important is chip ID since U-Boot SPL expects version 0x1. Besides
the chip ID register, reset values for two more registers used by A10
U-Boot SPL are covered.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20221226220303.14420-5-strahinja.p.jankovic@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Allwinner TWI/I2C controller emulation. Only
master-mode functionality is implemented.
The SPL boot for Cubieboard expects AXP209 PMIC on TWI0/I2C0 bus, so this is
first part enabling the TWI/I2C bus operation.
Since both Allwinner A10 and H3 use the same module, it is added for
both boards.
Docs are also updated for Cubieboard and Orangepi-PC board to indicate
I2C availability.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several DRAM Controller registers are used. Most
important registers are those related to DRAM initialization and
calibration, where SPL initiates process and waits until certain bit is
set/cleared.
This patch adds these registers, initializes reset values from user's
guide and updates state of registers as SPL expects it.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-3-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
During SPL boot several Clock Controller Module (CCM) registers are
read, most important are PLL and Tuning, as well as divisor registers.
This patch adds these registers and initializes reset values from user's
guide.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-2-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Olimex makes a series of low-cost STM32 boards. This commit introduces
the minimum setup to support SMT32-H405. See [1] for details
[1] https://www.olimex.com/Products/ARM/ST/STM32-H405/
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20221230145733.200496-3-balbi@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
STM32F405 has 128K of SRAM and another 64K of CCM (Core-coupled
Memory) at a different base address. Correctly describe the memory
layout to give existing FW images a chance to run unmodified.
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Message-id: 20221230145733.200496-2-balbi@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using --disable-virglrenderer, QEMU still creates
hw-display-virtio-gpu-gl.so
hw-display-virtio-vga-gl.so
hw-display-virtio-gpu-pci-gl.so
but when these are loaded, they provide no functionality as the code
which registers types is not compiled in. Funtionally this is
relatively harmless, because QEMU is fine loading a module with no
types.
This is rather confusing for users and OS distro maintainers though,
as they think they have the GL functionality built, but in fact the
module they are looking at provides nothing of value.
The root cause is the use of 'when/if_true' rules when adding sources
to the module source set. If all the rules evaluate to false, then we
have declared the module, but not added anything to it. We need to
put declaration of the entire module inside a condition based on
existance of the 3rd party library deps that are mandatory.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1352
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221219125830.2369169-1-berrange@redhat.com>
[Do not check for pixman. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20221219130205.687815-3-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This API allows the accelerators to prevent vcpus from issuing
new ioctls while execting a critical section marked with the
accel_ioctl_inhibit_begin/end functions.
Note that all functions submitting ioctls must mark where the
ioctl is being called with accel_{cpu_}ioctl_begin/end().
This API requires the caller to always hold the BQL.
API documentation is in sysemu/accel-blocker.h
Internally, it uses a QemuLockCnt together with a per-CPU QemuLockCnt
(to minimize cache line bouncing) to keep avoid that new ioctls
run when the critical section starts, and a QemuEvent to wait
that all running ioctls finish.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221111154758.1372674-2-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the local Error variable with errp and ERRP_GUARD() and change
the return value to bool.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Remove an unnecessary local Error value in nvme_realize(). In the
process, change nvme_check_constraints() to return a bool.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* Rework and improvements of the EINTR handling by Nikita
* Deprecate the -no-hpet command line option
* Disable the qtests in the 32-bit Windows CI job again
* Some other misc fixes here and there
-----BEGIN PGP SIGNATURE-----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=D+Yw
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-01-09' of https://gitlab.com/thuth/qemu into staging
* s390x header clean-ups from Philippe
* Rework and improvements of the EINTR handling by Nikita
* Deprecate the -no-hpet command line option
* Disable the qtests in the 32-bit Windows CI job again
* Some other misc fixes here and there
# gpg: Signature made Mon 09 Jan 2023 14:21:19 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-01-09' of https://gitlab.com/thuth/qemu:
.gitlab-ci.d/windows: Do not run the qtests in the msys2-32bit job
error handling: Use RETRY_ON_EINTR() macro where applicable
Refactoring: refactor TFR() macro to RETRY_ON_EINTR()
docs/interop: Change the vnc-ledstate-Pseudo-encoding doc into .rst
i386: Deprecate the -no-hpet QEMU command line option
tests/qtest/bios-tables-test: Replace -no-hpet with hpet=off machine parameter
tests/readconfig: spice doesn't support unix socket on windows yet
target/s390x: Restrict sysemu/reset.h to system emulation
target/s390x/tcg/excp_helper: Restrict system headers to sysemu
target/s390x/tcg/misc_helper: Remove unused "memory.h" include
hw/s390x/pv: Restrict Protected Virtualization to sysemu
exec/memory: Expose memory_region_access_valid()
MAINTAINERS: Add MIPS-related docs and configs to the MIPS architecture section
tests/vm: Update get_default_jobs() to work on non-x86_64 non-KVM hosts
qemu-iotests/stream-under-throttle: do not shutdown QEMU
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a defined RETRY_ON_EINTR() macro in qemu/osdep.h
which handles the same while loop.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/415
Signed-off-by: Nikita Ivanov <nivanov@cloudlinux.com>
Message-Id: <20221023090422.242617-3-nivanov@cloudlinux.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[thuth: Dropped the hunk that changed socket_accept() in libqtest.c]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Instead of having hardware device poking into memory
internal API, expose memory_region_access_valid().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221217152454.96388-2-philmd@linaro.org>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmO6eGMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpoUIIALqC3UtJcK3AuAMbeqVokxl5CPwoeXMyi+rT
0QuN8m8dpBtJFpy3Vyq0afixOFmlwvORW5ye4QI97OyIhtLJq00buzQsgHjNoPo3
zN2L0BDyofDmfFHgCxcEbv2aAO8TaqRSHmKffEFmf8JDMDL9Ev1QvPTWHhfm2eJf
VKPHOtCA/3WXBD9JNfYJ0YuzCrrJaMhIO6/5tqv9yjMxWTfEFa1J2Sr2tWkRLuDk
FPfApy7afjI705Guv6PllZ3JdOMwf7iZaoBK6mSdCDSyi1xciYM0VeWi8SLD4qbM
N+9NkUQOIYS5ZC4BXrULy6HDUsECJ71I0pvHveX7nwbK6xPD4RQ=
=0tPe
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 08 Jan 2023 08:01:39 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (50 commits)
vhost-scsi: fix memleak of vsc->inflight
acpi: cpuhp: fix guest-visible maximum access size to the legacy reg block
tests: acpi: aarch64: Add *.topology tables
tests: acpi: aarch64: Add topology test for aarch64
tests: acpi: Add and whitelist *.topology blobs
tests: virt: Update expected ACPI tables for virt test
hw/acpi/aml-build: Only generate cluster node in PPTT when specified
tests: virt: Allow changes to PPTT test table
virtio-pci: fix proxy->vector_irqfd leak in virtio_pci_set_guest_notifiers
vdpa: commit all host notifier MRs in a single MR transaction
vhost: configure all host notifiers in a single MR transaction
vhost: simplify vhost_dev_enable_notifiers
vdpa: harden the error path if get_iova_range failed
vdpa-dev: get iova range explicitly
docs/devel: Rules on #include in headers
include: Include headers where needed
include/hw/virtio: Break inclusion loop
include/hw/cxl: Break inclusion loop cxl_pci.h and cxl_cdat_h
include/hw/pci: Include hw/pci/pci.h where needed
include/hw/pci: Split pci_device.h off pci.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prior to reading the shadow doorbell cq head, we have to update the
eventidx. Otherwise, we risk that the driver will skip an mmio doorbell
write. This happens on riscv64, as reported by Guenter.
Adding the missing update to the cq eventidx fixes the issue.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Cc: qemu-riscv@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The eventidx and doorbell value are not handling endianness correctly.
Fix this.
Fixes: 3f7fe8de3d ("hw/nvme: Implement shadow doorbell buffer support")
Cc: qemu-stable@nongnu.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Rename the trace events related to writing the event index and reading
the doorbell value to make it more clear that the event is associated
with an actual update (write or read respectively).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Replace various ->parent_obj use with the equivalent QOM accessors.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
* Always send errors to logfile when daemonized (Greg)
* Add support for IDE CompactFlash card (Lubomir)
* First round of build system cleanups (myself)
* First round of feature removals (myself)
* Reduce "qemu/accel.h" inclusion (Philippe)
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmO3Ym0UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNYmwf+LHEw+4T0fk1+2NfgIzH3+8s1EqDm
Ai56EjxO/p5NUptflXAnhn4P3LawswmmNE0ZIFFFBgwG5E9L+Jj/u5efuLu4uYPg
bboEBDn8nxSNN2l08u9TyS6kSWSxbwwrs7i2+V+4uQIlVIcCHu+A0vpXns4vWwY0
zZGF8CgJKDQdPIxdXrH8+6/xtadQ8uDkYsAWDiY/nhozCsCUTAZGTXWEQbHJLARI
Z4X+Cmz/NFB9G4ka6K/y0HbQw99KA8G/EMPUSglN0ya10yjpyzrmeI7IlIves+5U
8lhCZXyBhaV9GXlIK1vIgEXlHf83C19a+v0DpW0bpxK631n2VR5y3CArBg==
=2Koq
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* Atomic memslot updates for KVM (Emanuele, David)
* Always send errors to logfile when daemonized (Greg)
* Add support for IDE CompactFlash card (Lubomir)
* First round of build system cleanups (myself)
* First round of feature removals (myself)
* Reduce "qemu/accel.h" inclusion (Philippe)
# gpg: Signature made Thu 05 Jan 2023 23:51:09 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (24 commits)
i386: SGX: remove deprecated member of SGXInfo
target/i386: Add SGX aex-notify and EDECCSSA support
util: remove support -chardev tty and -chardev parport
util: remove support for hex numbers with a scaling suffix
KVM: remove support for kernel-irqchip=off
docs: do not talk about past removal as happening in the future
meson: accept relative symlinks in "meson introspect --installed" data
meson: cleanup compiler detection
meson: support meson 0.64 -Doptimization=plain
configure: test all warnings
tests/qapi-schema: remove Meson workaround
meson: cleanup dummy-cpus.c rules
meson: tweak hardening options for Windows
configure: remove backwards-compatibility and obsolete options
configure: preserve qemu-ga variables
configure: cleanup $cpu tests
configure: remove dead function
configure: remove useless write_c_skeleton
ide: Add "ide-cf" driver, a CompactFlash card
ide: Add 8-bit data mode
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is below memleak detected when to quit the qemu-system-x86_64 (with
vhost-scsi-pci).
(qemu) quit
=================================================================
==15568==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0x7f00aec57917 in __interceptor_calloc (/lib64/libasan.so.6+0xb4917)
#1 0x7f00ada0d7b5 in g_malloc0 (/lib64/libglib-2.0.so.0+0x517b5)
#2 0x5648ffd38bac in vhost_scsi_start ../hw/scsi/vhost-scsi.c:92
#3 0x5648ffd38d52 in vhost_scsi_set_status ../hw/scsi/vhost-scsi.c:131
#4 0x5648ffda340e in virtio_set_status ../hw/virtio/virtio.c:2036
#5 0x5648ff8de281 in virtio_ioport_write ../hw/virtio/virtio-pci.c:431
#6 0x5648ff8deb29 in virtio_pci_config_write ../hw/virtio/virtio-pci.c:576
#7 0x5648ffe5c0c2 in memory_region_write_accessor ../softmmu/memory.c:493
#8 0x5648ffe5c424 in access_with_adjusted_size ../softmmu/memory.c:555
#9 0x5648ffe6428f in memory_region_dispatch_write ../softmmu/memory.c:1515
#10 0x5648ffe8613d in flatview_write_continue ../softmmu/physmem.c:2825
#11 0x5648ffe86490 in flatview_write ../softmmu/physmem.c:2867
#12 0x5648ffe86d9f in address_space_write ../softmmu/physmem.c:2963
#13 0x5648ffe86e57 in address_space_rw ../softmmu/physmem.c:2973
#14 0x5648fffbfb3d in kvm_handle_io ../accel/kvm/kvm-all.c:2639
#15 0x5648fffc0e0d in kvm_cpu_exec ../accel/kvm/kvm-all.c:2890
#16 0x5648fffc90a7 in kvm_vcpu_thread_fn ../accel/kvm/kvm-accel-ops.c:51
#17 0x56490042400a in qemu_thread_start ../util/qemu-thread-posix.c:505
#18 0x7f00ac3b6ea4 in start_thread (/lib64/libpthread.so.0+0x7ea4)
Free the vsc->inflight at the 'stop' path.
Fixes: b82526c7ee ("vhost-scsi: support inflight io track")
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Li Feng <fengli@smartx.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Message-Id: <20230104160433.21353-1-dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The modern ACPI CPU hotplug interface was introduced in the following
series (aa1dd39ca307..679dd1a957df), released in v2.7.0:
1 abd49bc2ed docs: update ACPI CPU hotplug spec with new protocol
2 16bcab97eb pc: piix4/ich9: add 'cpu-hotplug-legacy' property
3 5e1b5d9388 acpi: cpuhp: add CPU devices AML with _STA method
4 ac35f13ba8 pc: acpi: introduce AcpiDeviceIfClass.madt_cpu hook
5 d2238cb678 acpi: cpuhp: implement hot-add parts of CPU hotplug
interface
6 8872c25a26 acpi: cpuhp: implement hot-remove parts of CPU hotplug
interface
7 76623d00ae acpi: cpuhp: add cpu._OST handling
8 679dd1a957 pc: use new CPU hotplug interface since 2.7 machine type
Before patch#1, "docs/specs/acpi_cpu_hotplug.txt" only specified 1-byte
accesses for the hotplug register block. Patch#1 preserved the same
restriction for the legacy register block, but:
- it specified DWORD accesses for some of the modern registers,
- in particular, the switch from the legacy block to the modern block
would require a DWORD write to the *legacy* block.
The latter functionality was then implemented in cpu_status_write()
[hw/acpi/cpu_hotplug.c], in patch#8.
Unfortunately, all DWORD accesses depended on a dormant bug: the one
introduced in earlier commit a014ed07bd ("memory: accept mismatching
sizes in memory_region_access_valid", 2013-05-29); first released in
v1.6.0. Due to commit a014ed07bd, the DWORD accesses to the *legacy*
CPU hotplug register block would work in spite of the above series *not*
relaxing "valid.max_access_size = 1" in "hw/acpi/cpu_hotplug.c":
> static const MemoryRegionOps AcpiCpuHotplug_ops = {
> .read = cpu_status_read,
> .write = cpu_status_write,
> .endianness = DEVICE_LITTLE_ENDIAN,
> .valid = {
> .min_access_size = 1,
> .max_access_size = 1,
> },
> };
Later, in commits e6d0c3ce68 ("acpi: cpuhp: introduce 'Command data 2'
field", 2020-01-22) and ae340aa3d2 ("acpi: cpuhp: spec: add typical
usecases", 2020-01-22), first released in v5.0.0, the modern CPU hotplug
interface (including the documentation) was extended with another DWORD
*read* access, namely to the "Command data 2" register, which would be
important for the guest to confirm whether it managed to switch the
register block from legacy to modern.
This functionality too silently depended on the bug from commit
a014ed07bd.
In commit 5d971f9e67 ('memory: Revert "memory: accept mismatching sizes
in memory_region_access_valid"', 2020-06-26), first released in v5.1.0,
the bug from commit a014ed07bd was fixed (the commit was reverted).
That swiftly exposed the bug in "AcpiCpuHotplug_ops", still present from
the v2.7.0 series quoted at the top -- namely the fact that
"valid.max_access_size = 1" didn't match what the guest was supposed to
do, according to the spec ("docs/specs/acpi_cpu_hotplug.txt").
The symptom is that the "modern interface negotiation protocol"
described in commit ae340aa3d2:
> + Use following steps to detect and enable modern CPU hotplug interface:
> + 1. Store 0x0 to the 'CPU selector' register,
> + attempting to switch to modern mode
> + 2. Store 0x0 to the 'CPU selector' register,
> + to ensure valid selector value
> + 3. Store 0x0 to the 'Command field' register,
> + 4. Read the 'Command data 2' register.
> + If read value is 0x0, the modern interface is enabled.
> + Otherwise legacy or no CPU hotplug interface available
falls apart for the guest: steps 1 and 2 are lost, because they are DWORD
writes; so no switching happens. Step 3 (a single-byte write) is not
lost, but it has no effect; see the condition in cpu_status_write() in
patch#8. And step 4 *misleads* the guest into thinking that the switch
worked: the DWORD read is lost again -- it returns zero to the guest
without ever reaching the device model, so the guest never learns the
switch didn't work.
This means that guest behavior centered on the "Command data 2" register
worked *only* in the v5.0.0 release; it got effectively regressed in
v5.1.0.
To make things *even more* complicated, the breakage was (and remains, as
of today) visible with TCG acceleration only. Commit 5d971f9e67 makes
no difference with KVM acceleration -- the DWORD accesses still work,
despite "valid.max_access_size = 1".
As commit 5d971f9e67 suggests, fix the problem by raising
"valid.max_access_size" to 4 -- the spec now clearly instructs the guest
to perform DWORD accesses to the legacy register block too, for enabling
(and verifying!) the modern block. In order to keep compatibility for the
device model implementation though, set "impl.max_access_size = 1", so
that wide accesses be split before they reach the legacy read/write
handlers, like they always have been on KVM, and like they were on TCG
before 5d971f9e67 (v5.1.0).
Tested with:
- OVMF IA32 + qemu-system-i386, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32X64 + qemu-system-x86_64, CPU hotplug/hot-unplug with SMM,
intermixed with ACPI S3 suspend/resume, using KVM accel
(regression-test);
- OVMF IA32 + qemu-system-i386, SMM enabled, using TCG accel; verified the
register block switch and the present/possible CPU counting through the
modern hotplug interface, during OVMF boot (bugfix test);
- I do not have any testcase (guest payload) for regression-testing CPU
hotplug through the *legacy* CPU hotplug register block.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: qemu-stable@nongnu.org
Ref: "IO port write width clamping differs between TCG and KVM"
Link: http://mid.mail-archive.com/aaedee84-d3ed-a4f9-21e7-d221a28d1683@redhat.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2023-01/msg00199.html
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230105161804.82486-1-lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently we'll always generate a cluster node no matter user has
specified '-smp clusters=X' or not. Cluster is an optional level
and will participant the building of Linux scheduling domains and
only appears on a few platforms. It's unncessary to always build
it when it cannot reflect the real topology on platforms having no
cluster implementation and to avoid affecting the linux scheduling
domains in the VM. So only generate the cluster topology in ACPI
PPTT when the user has specified it explicitly in -smp.
Tested qemu-system-aarch64 with `-smp 8` and linux 6.1-rc1, without
this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
56 # cluster_id
with this patch:
estuary:/sys/devices/system/cpu/cpu0/topology$ cat cluster_*
ff # cluster_cpus
0-7 # cluster_cpus_list
36 # cluster_id, with no cluster node kernel will make it to
physical package id
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Message-Id: <20221229065513.55652-3-yangyicong@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
proxy->vector_irqfd did not free when kvm_virtio_pci_vector_use or
msix_set_vector_notifiers failed in virtio_pci_set_guest_notifiers.
Fixes: 7d37d351
Signed-off-by: Lei Xiang <leixiang@kylinos.cn>
Tested-by: Zeng Chi <zengchi@kylinos.cn>
Suggested-by: Xie Ming <xieming@kylinos.cn>
Message-Id: <20221227081604.806415-1-leixiang@kylinos.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows the vhost-vdpa device to batch the setup of all its MRs of
host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on setup the host notifier MRs reduce from 423ms to 32ms for a VM with
64 vCPUs and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device).
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-4-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This allows the vhost device to batch the setup of all its host notifiers.
This significantly reduces the device starting time, e.g. the time spend
on enabling notifiers reduce from 376ms to 9.1ms for a VM with 64 vCPUs
and 3 vhost-vDPA generic devices (vdpa_sim_blk, 64vq per device)
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-3-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Simplify the error path in vhost_dev_enable_notifiers by using
vhost_dev_disable_notifiers directly.
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221227072015.3134-2-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In commit a585fad26b ("vdpa: request iova_range only once") we remove
GET_IOVA_RANGE form vhost_vdpa_init, the generic vdpa device will start
without iova_range populated, so the device won't work. Let's call
GET_IOVA_RANGE ioctl explicitly.
Fixes: a585fad26b ("vdpa: request iova_range only once")
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221224114848.3062-2-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
hw/virtio/virtio.h and hw/virtio/vhost.h include each other. The
former doesn't actually need the latter, so drop that inclusion to
break the loop.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221222120813.727830-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/cxl/cxl.h uses the PXBDev structure tag instead of the typedef
name. The typedef name is defined in hw/pci/pci_bridge.h. Its
inclusion was dropped in the previous commit to break an inclusion
loop.
Move the typedef to hw/cxl/cxl.h, and use it there. Delete an extra
typedef in hw/pci-bridge/pci_expander_bridge.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/pci/pci_bridge.h and hw/cxl/cxl.h include each other.
Fortunately, breaking the loop is merely a matter of deleting
unnecessary includes from headers, and adding them back in places
where they are now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio.c is big enough, extract more QMP related code to virtio-qmp.c.
To do so, expose qmp_find_virtio_device() and declar virtio_list in
the internal virtio-qmp.h header.
Note we have to leave qmp_x_query_virtio_queue_status() and
qmp_x_query_virtio_queue_element(), because they access VirtQueue
internal fields, and VirtQueue is only declared within virtio.c.
Suggested-by: Jonah Palmer <jonah.palmer@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221222080005.27616-3-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To emphasize this function is QMP related, rename it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221222080005.27616-2-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add process to handle the configure interrupt, The function's
logic is the same with vq interrupt.Add extra process to check
the configure interrupt
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-11-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add configure interrupt support in virtio-mmio bus.
add function to set configure guest notifier.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-10-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt in virtio_net
Add the functions to support vhost_net_config_pending
and vhost_net_config_mask.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-9-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt.
The configure interrupt process will start in vhost_dev_start
and stop in vhost_dev_stop.
Also add the functions to support vhost_config_pending and
vhost_config_mask.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-8-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the functions to support the configure interrupt in virtio
The function virtio_config_guest_notifier_read will notify the
guest if there is an configure interrupt.
The function virtio_config_set_guest_notifier_fd_handler is
to set the fd hander for the notifier
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-7-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add new call back function in vhost-vdpa, The function
vhost_set_config_call can set the event fd to kernel.
This function will be called in the vhost_dev_start
and vhost_dev_stop
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-6-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the interrupt process in configure interrupt
Need to decouple the single vector from the interrupt process.
We add new function kvm_virtio_pci_vector_use_one and _release_one.
These functions are used for the single vector, the whole process will
finish in the loop with vq number.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-4-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the notifier process. We add the virtio_pci_get_notifier
to get the notifier and vector. The INPUT for this function is IDX,
The OUTPUT is the notifier and the vector
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-3-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221222070451.936503-2-lulu@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch aims to fix unexpected negotiation features for
vhost-user netdev interface.
When openvswitch reconnect Qemu after an unexpected disconnection
and Qemu therefore start the vhost_dev, acked_features field in
vhost_dev is initialized with value fetched from acked_features
field in NetVhostUserState, which should be up-to-date at that
moment but Qemu could not make it actually during the time window
of virtio features negotiation.
So we save the acked_features right after being configured by
guest virtio driver so it can be used to restore acked_features
field in vhost_dev correctly.
Signed-off-by: Hyman Huang(黄勇) <huangy81@chinatelecom.cn>
Signed-off-by: Guoyi Tu <tugy@chinatelecom.cn>
Signed-off-by: Liuxiangdong <liuxiangdong5@huawei.com>
Message-Id: <b9f8cf5561a79ea65ea38960e5a5e6d3707eef0a.1671627406.git.huangy81@chinatelecom.cn>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that all ACPI controllers select the ACPI and APM dependencies
themselves, these explicit dependencies became redundant. Remove them.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The ACPIREGS are provided by TYPE_VIA_PM, so needs to select ACPI.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
piix4_pm_realize() uses apm_init() and pm_smbus_init(), so both APM and
ACPI_SMBUS are provided by the device model managed by ACPI_PIIX4.
The ACPIREGS are also provided by ACPI_PIIX4, so needs to select ACPI.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
TYPE_PIIX4_PM is only used in machines where PIIX chipsets are used
which is currently PC and Malta. There is no point building it for the
other ACPI_X86 machines.
Note that this also removes unneeded ACPI_PIIX4 from PEGASOS2.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221216130355.41667-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
ich9_lpc_realize() uses apm_init() and ich9_smbus_realize() uses
pm_smbus_init(), so both APM and ACPI_SMBUS are provided by the device
models managed by ACPI_ICH9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although the ICH9 ACPI controller may currently be tied to x86 it
doesn't have to. Furthermore, the source files this configuration switch
manages contain a '9', so this name fits more.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216130355.41667-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Status part of the emulated feature. It will follow device model, so we
must copy it as long as NIC device model has it set.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20221221115015.1400889-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Next patches introduce more code on vhost-vdpa branch, with already have
too much indentation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221221115015.1400889-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY7e94gAKCRBAov/yOSY+
3+YwA/9JAerEGzZIJfV2+QK4LWONOfIt7Ns5TR93gTjd+9rTsahgSIHRa2XHQLWZ
TwY2eyTf8M+qiVOKa1wTCEfvr/iQwRuJBmsyQ/igdKgylEi9t6GEIG1NeGUxGkkR
sCBJMtcqB4OKIX6PlyRiOm9kJxnNgQuiQ6ZB7uqIcVuYC/wxzA==
=KsDP
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20230106
# gpg: Signature made Fri 06 Jan 2023 06:21:22 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_pch: Change default irq number of pch irq controller
hw/intc/loongarch_pch_pic: add irq number property
hw/intc/loongarch_pch_msi: add irq number property
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix PMP propagation for tlb
* Collection of bug fixes
* Bump the OpenTitan supported version
* Add smstateen support
* Support native debug icount trigger
* Remove the redundant ipi-id property in the virt machine
* Support cache-related PMU events in virtual mode
* Add some missing PolarFire SoC io regions
* Fix mret exception cause when no pmp rule is configured
* Fix bug where disabling compressed instructions would crash QEMU
* Add Zawrs ISA extension support
* A range of code refactoring and cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmO3b5sACgkQIeENKd+X
cFTD8Af+L0OaGzE4C0jil7LdITFKk7ltdTg3yw84ZBvIxrEWMWlt5Yj3Ez5OIPbY
WpPmCLoJ9XM/5CV5PuPjxcFFExWjXLNeMEvaaT/3/3jPPnA/M/AbZa4hefKRluTg
kkvBiOuRMPXiYLki5xAHmjD/1j6SQ8ghylPLxYQqyGq87WZt4Dx9msOTZLVzmmYl
8y9oC8j6yO2UBZYC1TxSkKxFbj+Cp2HmtBZ09tDzwRL6DpRvIlfftiLl8X3awMlK
YTzCIrmllc38/+cV9IpQhdXzDUZ1kM7Zy56JbJl3XOsS4VnUYGmEtrKYpYQ2CKLY
/tcmrDKNw1ArWcP1axNN8FHfhy1FyQ==
=SH+C
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230106' of https://github.com/alistair23/qemu into staging
First RISC-V PR for QEMU 8.0
* Fix PMP propagation for tlb
* Collection of bug fixes
* Bump the OpenTitan supported version
* Add smstateen support
* Support native debug icount trigger
* Remove the redundant ipi-id property in the virt machine
* Support cache-related PMU events in virtual mode
* Add some missing PolarFire SoC io regions
* Fix mret exception cause when no pmp rule is configured
* Fix bug where disabling compressed instructions would crash QEMU
* Add Zawrs ISA extension support
* A range of code refactoring and cleanups
# gpg: Signature made Fri 06 Jan 2023 00:47:23 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* tag 'pull-riscv-to-apply-20230106' of https://github.com/alistair23/qemu: (43 commits)
hw/intc: sifive_plic: Fix the pending register range check
hw/riscv: opentitan: Drop "hartid-base" and "priority-base" initialization
hw/intc: sifive_plic: Change "priority-base" to start from interrupt source 0
hw/riscv: virt: Fix the value of "riscv, ndev" in the dtb
hw/riscv: sifive_u: Avoid using magic number for "riscv, ndev"
hw/riscv: sifive_e: Fix the number of interrupt sources of PLIC
hw/riscv: microchip_pfsoc: Fix the number of interrupt sources of PLIC
hw/intc: sifive_plic: Update "num-sources" property default value
hw/intc: sifive_plic: Use error_setg() to propagate the error up via errp in sifive_plic_realize()
hw/intc: sifive_plic: Improve robustness of the PLIC config parser
hw/intc: sifive_plic: Drop PLICMode_H
hw/riscv: spike: Remove misleading comments
hw/riscv: Sort machines Kconfig options in alphabetical order
hw/riscv: Fix opentitan dependency to SIFIVE_PLIC
hw/intc: Select MSI_NONBROKEN in RISC-V AIA interrupt controllers
hw/riscv: Select MSI_NONBROKEN in SIFIVE_PLIC
RISC-V: Add Zawrs ISA extension support
target/riscv: Clear mstatus.MPRV when leaving M-mode for priv spec 1.12+
target/riscv: Simplify helper_sret() a little bit
target/riscv: Set pc_succ_insn for !rvc illegal insn
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add tcg backend paired register allocation.
Cleanup tcg backend function call abi.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmO3kZEdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV/JpwgAj9kwpiWehGWrpQp9
rbEL+Fsx+SDhnoLVpF6nmSB1nkDqdgkdnhyRaLX9wM69bnocsGppZ5sd57J/cH3m
WiODVVbWP80WHonx5EN4htQv99TZWqVmXVl11DwOfsRUmINl4GG4kvHOOABd8hdc
39eRgGBBMyMShc6MUJiToyjEAcZPcGAiHkSW9YDGbvzhlloNWh46eLP1bdW3UJWK
UiEwPpXqg+L0V8nuuQnSFoPr5FIJmmoTeiGCRHXtvgOT7J8/6eKUESpfcKkHq1ye
dwcJQATuZip3+hyCCVveiZ86TQ81RMp9en1qw+HVzfed1Ial3Tk+tqiDqZJFm25b
GMpa5g==
=OjPl
-----END PGP SIGNATURE-----
Merge tag 'pull-tcg-20230105' of https://gitlab.com/rth7680/qemu into staging
Fix race conditions in new user-only vma tracking.
Add tcg backend paired register allocation.
Cleanup tcg backend function call abi.
# gpg: Signature made Fri 06 Jan 2023 03:12:17 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* tag 'pull-tcg-20230105' of https://gitlab.com/rth7680/qemu: (47 commits)
tests/tcg/multiarch: add vma-pthread.c
accel/tcg: Handle false negative lookup in page_check_range
accel/tcg: Use g_free_rcu for user-exec interval trees
accel/tcg: Fix tb_invalidate_phys_page_unwind
tcg: Add TCGHelperInfo argument to tcg_out_call
tcg/aarch64: Merge tcg_out_callr into tcg_out_call
tcg: Move ffi_cif pointer into TCGHelperInfo
tcg: Factor init_ffi_layouts() out of tcg_context_init()
tcg: Convert typecode_to_ffi from array to function
tcg: Reorg function calls
tcg: Use output_pref wrapper function
tcg: Vary the allocation size for TCGOp
tcg: Pass number of arguments to tcg_emit_op() / tcg_op_insert_*()
accel/tcg/plugin: Use copy_op in append_{udata,mem}_cb
accel/tcg/plugin: Avoid duplicate copy in copy_call
accel/tcg/plugin: Don't search for the function pointer index
tcg: Use TCG_CALL_ARG_EVEN for TCI special case
tcg: Replace TCG_TARGET_EXTEND_ARGS with TCG_TARGET_CALL_ARG_I32
tcg: Replace TCG_TARGET_CALL_ALIGN_ARGS with TCG_TARGET_CALL_ARG_I64
tcg: Introduce TCGCallReturnKind and TCGCallArgumentKind
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the default irq number of pch pic to 32, so that the irq
number of pch msi is 224(256 - 32), and move the 'PCH_PIC_IRQ_NUM'
macro to pci-host/ls7a.h and add prefix 'VIRT' on it to keep standard
format.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-4-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
With loongarch 7A1000 manual, irq number supported can be set
in PCH_PIC_INT_ID_HI register. This patch adds irq number property
for loongarch_pch_pic, so that virt machine can set different
irq number when pch_pic intc is added.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230104020518.2564263-3-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This patch adds irq number property for loongarch msi interrupt
controller, and remove hard coding irq number macro.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-2-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The pending register upper limit is currently set to
plic->num_sources >> 3, which is wrong, e.g.: considering
plic->num_sources is 7, the upper limit becomes 0 which fails
the range check if reading the pending register at pending_base.
Fixes: 1e24429e40 ("SiFive RISC-V PLIC Block")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-16-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
"hartid-base" and "priority-base" are zero by default. There is no
need to initialize them to zero again.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-15-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
changed the value of VIRT_IRQCHIP_NUM_SOURCES from 127 to 53, which
is VIRTIO_NDEV and also used as the value of "riscv,ndev" property
in the dtb. Unfortunately this is wrong as VIRT_IRQCHIP_NUM_SOURCES
should include interrupt source 0 but "riscv,ndev" does not.
While we are here, we also fix the comments of platform bus irq range
which is now "64 to 96", but should be "64 to 95", introduced since
commit 1832b7cb3f ("hw/riscv: virt: Create a platform bus").
Fixes: 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-13-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present magic number is used to create "riscv,ndev" property
in the dtb. Let's use the macro SIFIVE_U_PLIC_NUM_SOURCES that
is used to instantiate the PLIC model instead.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-12-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the default value of "num-sources" property is zero,
which does not make a lot of sense, as in sifive_plic_realize()
we see s->bitfield_words is calculated by:
s->bitfield_words = (s->num_sources + 31) >> 5;
if the we don't configure "num-sources" property its default value
zero makes s->bitfield_words zero too, which isn't true because
interrupt source 0 still occupies one word.
Let's change the default value to 1 meaning that only interrupt
source 0 is supported by default and a sanity check in realize().
While we are here, add a comment to describe the exact meaning of
this property that the number should include interrupt source 0.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-9-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The realize() callback has an errp for us to propagate the error up.
While we are here, correct the wrong multi-line comment format.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PLIC config parser can only handle legal config string
like "MS,MS". However if a config string like ",MS,MS,,MS,MS,," is
given the parser won't get the correct configuration.
This commit improves the config parser to make it more robust.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-7-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
H-mode has been removed since priv spec 1.10. Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
PLIC is not included in the 'spike' machine.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-5-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SHAKTI_C machine Kconfig option was inserted in disorder. Fix it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-4-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since commit ef63100648 ("hw/riscv: opentitan: Update to the latest build")
the IBEX PLIC model was replaced with the SiFive PLIC model in the
'opentitan' machine but we forgot the add the dependency there.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-3-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in both riscv_aplic_realize() and
riscv_imsic_realize().
Select MSI_NONBROKEN in RISCV_APLIC and RISCV_IMSIC.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-2-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in sifive_plic_realize().
Let SIFIVE_PLIC select MSI_NONBROKEN and drop the selection from
RISC-V machines.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the number of interrupt is not multiple of 32, PLIC will have
out-of-bound access to source_priority array. Compute the number of
interrupt in the last word to avoid this out-of-bound access of array.
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221127165753.30533-1-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The system controller on PolarFire SoC is access via a mailbox. The
control registers for this mailbox lie in the "IOSCB" region & the
interrupt is cleared via write to the "SYSREG" region. It also has a
QSPI controller, usually connected to a flash chip, that is used for
storing FPGA bitstreams and used for In-Application Programming (IAP).
Linux has an implementation of the system controller, through which the
hwrng is accessed, leading to load/store access faults.
Add the QSPI as unimplemented and a very basic (effectively
unimplemented) version of the system controller's mailbox. Rather than
purely marking the regions as unimplemented, service the mailbox
requests by reporting failures and raising the interrupt so a guest can
better handle the lack of support.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221117225518.4102575-4-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Fabric Interconnect Controllers provide interfaces between the FPGA
fabric and the core complex. There are 5 FICs on PolarFire SoC, numbered
0 through 4. FIC2 is an AXI4 slave interface from the FPGA fabric and
does not show up on the MSS memory map. FIC4 is dedicated to the User
Crypto Processor and does not show up on the MSS memory map either.
FIC 0, 1 & 3 do show up in the MSS memory map and neither FICs 0 or 1
are represented in QEMU, leading to load access violations while booting
Linux for Icicle if PCIe is enabled as the root port is connected via
either FIC 0 or 1.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-3-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On PolarFire SoC, some peripherals (eg the PCI root port) are clocked by
"Clock Conditioning Circuitry" in the FPGA. The specific clock depends
on the FPGA bitstream & can be locked to one particular {D,P}LL - in the
Icicle Kit Reference Design v2022.09 or later this is/will be the case.
Linux v6.1+ will have a driver for this peripheral and devicetrees that
previously relied on "fixed-frequency" clock nodes have been switched
over to clock-controller nodes. The IOSCB region is represented in QEMU,
but the specific region of it that the CCCs occupy has not so v6.1-rcN
kernels fail to boot in QEMU.
Add the regions as unimplemented so that the status-quo in terms of boot
is maintained.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-2-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The imsic DT binding[1] has changed and no longer require an ipi-id.
The latest IMSIC driver dynamically allocates ipi id if slow-ipi
is not defined.
Get rid of the unused dt property which may lead to confusion.
[1] https://lore.kernel.org/lkml/20221111044207.1478350-5-apatel@ventanamicro.com/
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221122080529.1692533-1-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 40244040a7 changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adds the updated `aon_timer` base as an unimplemented device. This is
used by TockOS, patch ensures the guest doesn't hit load faults.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221025043335.339815-3-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch updates the OpenTitan model to match
the specified register layout as per [1]. Which is also the latest
commit of OpenTitan supported by TockOS.
Note: Pinmux and Padctrl has been merged into Pinmux [2][3], this patch removes
any references to Padctrl. Note: OpenTitan doc [2] has not yet specified
much detail regarding this, except for a note that states `TODO: this
section needs to be updated to reflect the pinmux/padctrl merger`
[1] d072ac505f/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h
[2] https://docs.opentitan.org/hw/top_earlgrey/doc/design/
[3] https://docs.opentitan.org/hw/ip/pinmux/doc/#overview
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20221025043335.339815-2-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
-machine kernel-irqchip=off is broken for many guest OSes; kernel-irqchip=split
is the replacement that works, so remove the deprecated support for the former.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows attaching IDE_CFATA device to an IDE bus. Behaves like a
CompactFlash card in True IDE mode.
Tested with:
qemu-system-i386 \
-device driver=ide-cf,drive=cf,bus=ide.0 \
-drive id=cf,index=0,format=raw,if=none,file=cf.img
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Message-Id: <20221130120319.706885-1-lkundrak@v3.sk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CompactFlash uses features 0x01 and 0x81 to enable/disable 8-bit data
path. Implement them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Message-Id: <20221130120238.706717-1-lkundrak@v3.sk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move "qemu/accel.h" include from the heavily included
"hw/boards.h" to hw/core/machine.c, the single file using
the AccelState definition.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Message-Id: <20221130135641.85328-3-philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While we initialize this value in cpu_common_reset, that
isn't called during startup, so set it as well in init.
This fixes -singlestep versus the very first TB.
Fixes: 04f5b647ed ("accel/tcg: Handle -singlestep in curr_cflags")
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Size is used at lines 1088/1188 for the loop, which reads the last 4
bytes from the crc_ptr so it does need to get increased, however it
shouldn't be increased before the buffer is passed to CRC computation,
or the crc32 function will access uninitialized memory.
This was pointed out to me by clg@kaod.org during the code review of
a similar patch to hw/net/ftgmac100.c
Change-Id: Ib0464303b191af1e28abeb2f5105eb25aadb5e9b
Signed-off-by: Stephen Longfield <slongfield@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20221221183202.3788132-1-slongfield@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
IRQs were not associated to the various GPIO devices inside i.MX7D.
This patch brings the i.MX7D on par with i.MX6.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 20221226101418.415170-1-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The i.MX6UL doesn't support CLK_HIGH ou CLK_HIGH_DIV clock source.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CCM derived clocks will have to be added later.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So far the GPT timers were unable to raise IRQs to the processor.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using Clang ("Apple clang version 14.0.0 (clang-1400.0.29.202)")
and building with -Wall we get:
hw/arm/smmu-common.c:173:33: warning: static function 'smmu_hash_remove_by_asid_iova' is used in an inline function with external linkage [-Wstatic-in-inline]
hw/arm/smmu-common.h:170:1: note: use 'static' to give inline function 'smmu_iotlb_inv_iova' internal linkage
void smmu_iotlb_inv_iova(SMMUState *s, int asid, dma_addr_t iova,
^
static
None of our code base require / use inlined functions with external
linkage. Some places use internal inlining in the hot path. These
two functions are certainly not in any hot path and don't justify
any inlining, so these are likely oversights rather than intentional.
Reported-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221216214924.4711-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function is not used anywhere outside this file,
so we can make the function "static void".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221216214924.4711-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Silent when compiling with -Wextra:
../hw/arm/nseries.c:1081:12: warning: missing field 'line' initializer [-Wmissing-field-initializers]
{ NULL }
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221220142520.24094-4-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221220142520.24094-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pointed MouseTransformInfo structure is accessed read-only.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221220142520.24094-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"Host Memory Backends" and "Memory devices" queue ("mem"):
- virtio-mem fixes
- Use new MPOL_PREFERRED_MANY mbind() policy for memory backends if
possible
-----BEGIN PGP SIGNATURE-----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=aVS3
-----END PGP SIGNATURE-----
Merge tag 'mem-2023-01-02' of https://github.com/davidhildenbrand/qemu into staging
Hi,
"Host Memory Backends" and "Memory devices" queue ("mem"):
- virtio-mem fixes
- Use new MPOL_PREFERRED_MANY mbind() policy for memory backends if
possible
# gpg: Signature made Mon 02 Jan 2023 11:22:04 GMT
# gpg: using RSA key 1BD9CAAD735C4C3A460DFCCA4DDE10F700FF835A
# gpg: issuer "david@redhat.com"
# gpg: Good signature from "David Hildenbrand <david@redhat.com>" [marginal]
# gpg: aka "David Hildenbrand <davidhildenbrand@gmail.com>" [full]
# gpg: aka "David Hildenbrand <hildenbr@in.tum.de>" [unknown]
# Primary key fingerprint: 1BD9 CAAD 735C 4C3A 460D FCCA 4DDE 10F7 00FF 835A
* tag 'mem-2023-01-02' of https://github.com/davidhildenbrand/qemu:
hostmem: Honor multiple preferred nodes if possible
virtio-mem: Fix typo in function name
virtio-mem: Fix the iterator variable in a vmem->rdl_list loop
virtio-mem: Fix the bitmap index of the section offset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- fix#1263 for CR writes
- rework compare time handling
- The compare timer has to run even if CR.OCIEN is not set,
as SR.OCIF must be updated.
- The compare timer fires exactly once when the
compare value is less than the current value, but the
reload values is less than the compare value.
- The compare timer will never fire if the reload value is
less than the compare value. Disable it in this case.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
[PMM: fixed minor style nits]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CNT register is a read-only register. There is no need to
store it's value, it can be calculated on demand.
The calculated frequency is needed temporarily only.
Note that this is a migration compatibility break for all boards
types that use the EPIT peripheral.
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interrupt state can change due to:
- reset clears both SR.OCIF and CR.OCIE
- write to CR.EN or CR.OCIE
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix typos, add background information
Signed-off-by: Axel Heider <axel.heider@hensoldt.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221228130956.80515-1-philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
It should be the variable rdl2 to revert the already-notified listeners.
Fixes: 2044969f0b ("virtio-mem: Implement RamDiscardManager interface")
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20221228090312.17276-1-chenyi.qiang@intel.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
vmem->bitmap indexes the memory region of the virtio-mem backend at a
granularity of block_size. To calculate the index of target section offset,
the block_size should be divided instead of the bitmap_size.
Fixes: 2044969f0b ("virtio-mem: Implement RamDiscardManager interface")
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20221216062231.11181-1-chenyi.qiang@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: David Hildenbrand <david@redhat.com>
xxxat() APIs are only available on POSIX platforms. For future
extension to Windows, let's replace the direct call to xxxat()
APIs with a wrapper.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20221219102022.2167736-4-bin.meng@windriver.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
These are not used anywhere in the source tree. Drop them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20221219102022.2167736-3-bin.meng@windriver.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
The qemu_v9fs_synth_mkdir() and qemu_v9fs_synth_add_file() functions
currently return a positive errno value on failure. This causes
checkpatch.pl to spit several errors like the one below:
ERROR: return of an errno should typically be -ve (return -EAGAIN)
+ return EAGAIN;
Simply change the sign. This has no consequence since callers
assert() the returned value to be equal to 0.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <166930551818.827792.10663674346122681963.stgit@bahia>
[C.S.: - Resolve conflict with 66997c42e0. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
This queue contains a MAINTAINERS update, the implementation of the Freescale eSDHC,
the introduction of the DEXCR/HDEXCR instructions and other assorted fixes (most of
them for the e500 board).
-----BEGIN PGP SIGNATURE-----
iIwEABYKADQWIQQX6/+ZI9AYAK8oOBk82cqW3gMxZAUCY6M//RYcZGFuaWVsaGI0
MTNAZ21haWwuY29tAAoJEDzZypbeAzFkaNABAKfQ/zpg2ugr/SmC7Ee9tnFNxDrq
JsNw+roXpUZvnkUZAQCMRm4BxfaXhXikRaSL2ZfGRtybKXki5o3Ez+rLxISiAg==
=gRo7
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20221221' of https://gitlab.com/danielhb/qemu into staging
ppc patch queue for 2022-12-21:
This queue contains a MAINTAINERS update, the implementation of the Freescale eSDHC,
the introduction of the DEXCR/HDEXCR instructions and other assorted fixes (most of
them for the e500 board).
# gpg: Signature made Wed 21 Dec 2022 17:18:53 GMT
# gpg: using EDDSA key 17EBFF9923D01800AF2838193CD9CA96DE033164
# gpg: issuer "danielhb413@gmail.com"
# gpg: Good signature from "Daniel Henrique Barboza <danielhb413@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 17EB FF99 23D0 1800 AF28 3819 3CD9 CA96 DE03 3164
* tag 'pull-ppc-20221221' of https://gitlab.com/danielhb/qemu:
target/ppc: Check DEXCR on hash{st, chk} instructions
target/ppc: Implement the DEXCR and HDEXCR
hw/ppc/e500: Move comment to more appropriate place
hw/ppc/e500: Resolve variable shadowing
hw/ppc/e500: Prefer local variable over qdev_get_machine()
hw/ppc/virtex_ml507: Prefer local over global variable
target/ppc/mmu_common: Fix table layout of "info tlb" HMP command
target/ppc/mmu_common: Log which effective address had no TLB entry found
hw/ppc/spapr: Reduce "vof.h" inclusion
hw/ppc/vof: Do not include the full "cpu.h"
target/ppc/kvm: Add missing "cpu.h" and "exec/hwaddr.h"
hw/ppc/e500: Add Freescale eSDHC to e500plat
hw/sd/sdhci: Support big endian SD host controller interfaces
MAINTAINERS: downgrade PPC KVM/TCG CPUs and pSeries to 'Odd Fixes'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TLB entries are set up in mmubooke_create_initial_mapping(), not in
booke206_page_size_to_tlb().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20221216145709.271940-7-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Assign to the outer variable instead which even saves some code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20221216145709.271940-6-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216145709.271940-5-shentey@gmail.com>
[danielhb: remove linebreak in object_property_add_child()]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216145709.271940-4-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Currently objects including "hw/ppc/spapr.h" are forced to be
target specific due to the inclusion of "vof.h" in "spapr.h".
"spapr.h" only uses a Vof pointer, so doesn't require the structure
declaration. The only place where Vof structure is accessed is in
spapr.c, so include "vof.h" there, and forward declare the structure
in "spapr.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221213123550.39302-4-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Adds missing functionality to e500plat machine which increases the
chance of given "real" firmware images to access SD cards.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221018210146.193159-8-shentey@gmail.com>
[PMD: Simplify using create_unimplemented_device("esdhc")]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221101222934.52444-4-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some SDHCI IP can be synthetized in various endianness:
https://github.com/u-boot/u-boot/blob/v2021.04/doc/README.fsl-esdhc
- CONFIG_SYS_FSL_ESDHC_BE
ESDHC IP is in big-endian mode. Accessing ESDHC registers can be
determined by ESDHC IP's endian mode or processor's endian mode.
Our current implementation is little-endian. In order to support
big endianness:
- Rename current MemoryRegionOps as sdhci_mmio_le_ops ('le')
- Add an 'endianness' property to SDHCIState (default little endian)
- Set the 'io_ops' field in realize() after checking the property
- Add the sdhci_mmio_be_ops (big-endian) MemoryRegionOps.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20221101222934.52444-3-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
make TCO watchdog work by default
part of generic vdpa support
asid interrupt for vhost-vdpa
added flex bus port DVSEC for cxl
misc fixes, cleanups, documentation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmOi/OQPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpGCkH/j06y7PEDHfG1MnPoFQIEWKHPyU/FMUe1RCW
dRsfVmHZ8Jc1Jy4wVch461QpcIC+WL/Fshzh92G0hVDI2AWzJOxzpWQESmCphJJG
Olk/H/ort4ZIrwOynAHDKLzgltoTI91uao3UT7w67NumAgVYYW4Q9ObHm2G3Wmwc
fe763NmlObrNYYCIbJw/KiBLrk7M5LaMLPeoRGJefD4MYUAPXy/sUQt61VyuZpuG
xFAeDB7/76MXFKJVjccSnZfa8lihOJ5AlvCBTjjY5PbGl8+U1usdd3hOVComYb02
LW4sKLkxe5sycg/bFQdBLpz2lZVlMjpY9nd9YiumIrgLBv70Uf0=
=WyvK
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
make TCO watchdog work by default
part of generic vdpa support
asid interrupt for vhost-vdpa
added flex bus port DVSEC for cxl
misc fixes, cleanups, documentation
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 21 Dec 2022 12:32:36 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (41 commits)
contrib/vhost-user-blk: Replace lseek64 with lseek
libvhost-user: Switch to unsigned int for inuse field in struct VuVirtq
hw/virtio: Extract QMP related code virtio-qmp.c
hw/virtio: Extract config read/write accessors to virtio-config-io.c
hw/virtio: Constify qmp_virtio_feature_map_t[]
hw/virtio: Guard and restrict scope of qmp_virtio_feature_map_t[]
hw/virtio: Rename virtio_ss[] -> specific_virtio_ss[]
hw/virtio: Add missing "hw/core/cpu.h" include
hw/cxl/device: Add Flex Bus Port DVSEC
hw/acpi: Rename tco.c -> ich9_tco.c
acpi/tests/avocado/bits: add mformat as one of the dependencies
docs/acpi/bits: document BITS_DEBUG environment variable
pci: drop redundant PCIDeviceClass::is_bridge field
remove DEC 21154 PCI bridge
vhost: fix vq dirty bitmap syncing when vIOMMU is enabled
acpi/tests/avocado/bits: add SPDX license identifiers for bios bits tests
include/hw: attempt to document VirtIO feature variables
vhost-user: send set log base message only once
vdpa: always start CVQ in SVQ mode if possible
vdpa: add shadow_data to vhost_vdpa
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The monitor decoders are the only functions using the CONFIG_xxx
definitions declared in the target specific CONFIG_DEVICES header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-7-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <a class="moz-txt-link-rfc2396E" href="mailto:philmd@linaro.org"><philmd@linaro.org></a>
These config helpers use the target-dependent LD/ST API.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-6-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These arrays are only accessed read-only, move them to .rodata.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-5-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jonah Palmer<jonah.palmer@oracle.com>
Signed-off-by: Philippe Mathieu-Daudé <a class="moz-txt-link-rfc2396E" href="mailto:philmd@linaro.org"><philmd@linaro.org></a>
Commit f3034ad71f ("qmp: decode feature & status bits in
virtio-status") did not guard all qmp_virtio_feature_map_t
arrays with the corresponding #ifdef'ry used in
qmp_decode_features(). Fix that and reduce the arrays scope
by declaring them static.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-4-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jonah Palmer<jonah.palmer@oracle.com>
Suggested-by: Richard Henderson <a class="moz-txt-link-rfc2396E" href="mailto:richard.henderson@linaro.org"><richard.henderson@linaro.org></a>
Signed-off-by: Philippe Mathieu-Daudé <a class="moz-txt-link-rfc2396E" href="mailto:philmd@linaro.org"><philmd@linaro.org></a>
Since virtio_ss[] is added to specific_ss[], rename it as
specific_virtio_ss[] to make it clearer.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-3-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio.c uses target_words_bigendian() which is declared in
"hw/core/cpu.h". Add the missing header to avoid when refactoring:
hw/virtio/virtio.c:2451:9: error: implicit declaration of function 'target_words_bigendian' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
if (target_words_bigendian()) {
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221213111707.34921-2-philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Flex Bus Port DVSEC was missing on type 3 devices which was blocking
RAS checks.[1]
Add the Flex Bus Port DVSEC to type 3 devices as per CXL 3.0 8.2.1.3.
[1] https://lore.kernel.org/linux-cxl/167096738875.2861540.11815053323626849940.stgit@djiang5-desk3.ch.intel.com/
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Ben Widawsky <bwidawsk@kernel.org>
Cc: qemu-devel@nongnu.org
Cc: linux-cxl@vger.kernel.org
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Message-Id: <20221213-ira-flexbus-port-v2-1-eaa48d0e0700@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
tco.c contains the ICH9 implementation of its "total cost
of ownership". Rename it accordingly to emphasis this is
a part of the ICH9 model.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221212105115.2113-1-philmd@linaro.org>
Acked-by: Igor Mammedov <imammedo@redhat.com>
and use cast to TYPE_PCI_BRIDGE instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221129101341.185621-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Code has not been used practically since its inception (2004)
f2aa58c6f4 UniNorth PCI bridge support
or maybe even earlier, but it was consuming contributors time
as QEMU was being rewritten.
Drop it for now. Whomever would like to actually
use the thing, can make sure it actually works/reintroduce
it back when there is a user.
PS:
I've stumbled upon this when replacing PCIDeviceClass::is_bridge
field with QOM cast to PCI_BRIDGE type. Unused DEC 21154
was the only one trying to use the field with plain PCIDevice.
It's not worth keeping the field around for the sake of the code
that was commented out 'forever'.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221129101341.185621-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When vIOMMU is enabled, the vq->used_phys is actually the IOVA not
GPA. So we need to translate it to GPA before the syncing otherwise we
may hit the following crash since IOVA could be out of the scope of
the GPA log size. This could be noted when using virtio-IOMMU with
vhost using 1G memory.
Fixes: c471ad0e9b ("vhost_net: device IOTLB support")
Cc: qemu-stable@nongnu.org
Tested-by: Lei Yang <leiyang@redhat.com>
Reported-by: Yalan Zhang <yalzhang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221216033552.77087-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Vhost message VHOST_USER_SET_LOG_BASE is device wide. So only
send it once with the first queue pair.
Signed-off-by: Yajun Wu <yajunw@nvidia.com>
Acked-by: Parav Pandit <parav@nvidia.com>
Message-Id: <20221122051447.248462-1-yajunw@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Isolate control virtqueue in its own group, allowing to intercept control
commands but letting dataplane run totally passthrough to the guest.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20221215113144.322011-13-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
The memory listener that thells the device how to convert GPA to qemu's
va is registered against CVQ vhost_vdpa. memory listener translations
are always ASID 0, CVQ ones are ASID 1 if supported.
Let's tell the listener if it needs to register them on iova tree or
not.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-12-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So the caller can choose which ASID is destined.
No need to update the batch functions as they will always be called from
memory listener updates at the moment. Memory listener updates will
always update ASID 0, as it's the passthrough ASID.
All vhost devices's ASID are 0 at this moment.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-10-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SVQ may run or not in a device depending on runtime conditions (for
example, if the device can move CVQ to its own group or not).
Allocate the SVQ array unconditionally at startup, since its hard to
move this allocation elsewhere.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-9-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The next patches will start control SVQ if possible. However, we don't
know if that will be possible at qemu boot anymore.
Since the moved checks will be already evaluated at net/ to know if it
is ok to shadow CVQ, move them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-8-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently iova range is requested once per queue pair in the case of
net. Reduce the number of ioctls asking it once at initialization and
reusing that value for each vhost_vdpa.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20221215113144.322011-7-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasonwang@redhat.com>
Since we don't know if we will use SVQ at qemu initialization, let's
allocate iova_tree only if needed. To do so, accept it at SVQ start, not
at initialization.
This will avoid to create it if the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-5-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The next patches will start control SVQ if possible. However, we don't
know if that will be possible at qemu boot anymore.
Delay device file descriptors until we know it at device start. This
will avoid to create them if the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By the end of this series CVQ is shadowed as long as the features
support it.
Since we don't know at the beginning of qemu running if this is
supported, move the event notifier handler setting to the start of the
SVQ, instead of the start of qemu run. This will avoid to create them if
the device does not support SVQ.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This function used to trust in v->shadow_vqs != NULL to know if it must
start svq or not.
This is not going to be valid anymore, as qemu is going to allocate svq
array unconditionally (but it will only start them conditionally).
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221215113144.322011-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The generic vDPA device doesn't support migration currently, so
mark it as unmigratable temporarily.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221215134944.2809-5-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Supports vdpa-dev-pci, we can use the device as follow:
-device vhost-vdpa-device-pci,vhostdev=/dev/vhost-vdpa-X
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221215134944.2809-4-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Supports vdpa-dev, we can use the deivce directly:
-M microvm -m 512m -smp 2 -kernel ... -initrd ... -device \
vhost-vdpa-device,vhostdev=/dev/vhost-vdpa-x
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221215134944.2809-3-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add helpers to get the "Transitional PCI Device ID" and "class_id"
of the device specified by the "Virtio Device ID".
These helpers will be used to build the generic vDPA device later.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Message-Id: <20221215134944.2809-2-longpeng2@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An 'ICH9-LPC.enable_tco' property has been exposed for a
very long time, but attempts to set it have never been
honoured.
Originally, any user provided 'enable_tco' value was force
replaced by a value passed from the machine type setup
code that was determine by machine type compat properties.
commit d6b304ba92
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:10 2016 -0200
machine: Remove no_tco field
The field is always set to zero, so it is not necessary anymore.
After legacy Q35 machine types were deleted in:
commit 86165b499e
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:09 2016 -0200
q35: Remove old machine versions
the machine type code ended up just unconditionally passing
'true', all the time, so this was further simplified in
commit d6b304ba92
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:10 2016 -0200
machine: Remove no_tco field
The field is always set to zero, so it is not necessary anymore.
commit 18d6abae3e
Author: Eduardo Habkost <ehabkost@redhat.com>
Date: Sat Jan 23 14:02:11 2016 -0200
ich9: Remove enable_tco arguments from init functions
The enable_tco arguments are always true, so they are not needed
anymore.
Leaving the ich9_pm_init to just force set 'enable_tco' to true.
This still overrides any user specified property. The initialization
of property defaults should be done when properties are first
registered, rather than during object construction.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-6-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The TCO watchdog implementation default behaviour from POV of the
guest OS relies on the initial values for two I/O ports:
* TCO1_CNT == 0x0
Since bit 11 (TCO Timer Halt) is clear, the watchdog state
is considered to be initially running
* GCS == 0x20
Since bit 5 (No Reboot) is set, the watchdog will not trigger
when the timer expires
This is a safe default, because the No Reboot bit will prevent the
watchdog from triggering if the guest OS is unaware of its existance,
or is slow in configuring it. When a Linux guest initializes the TCO
watchdog, it will attempt to clear the "No Reboot" flag, and read the
value back. If the clear was honoured, the driver will treat this as
an indicator that the watchdog is functional and create the guest
watchdog device.
QEMU implements a second "no reboot" flag, however, via pin straps
which overrides the behaviour of the guest controlled "no reboot"
flag:
commit 5add35bec1
Author: Paulo Alcantara <pcacjr@gmail.com>
Date: Sun Jun 28 14:58:58 2015 -0300
ich9: implement strap SPKR pin logic
This second 'noreboot' pin was defaulted to high, which also inhibits
triggering of the requested watchdog actions, unless QEMU is launched
with the magic flag "-global ICH9-LPC.noreboot=false".
This is a bad default as we are exposing a watchdog to every guest OS
using the q35 machine type, but preventing it from actually doing what
it is designed to do. What is worse is that the guest OS and its apps
have no way to know that the watchdog is never going to fire, due to
this second 'noreboot' pin.
If a guest OS had no watchdog device at all, then apps whose operation
and/or data integrity relies on a watchdog can refuse to launch, and
alert the administrator of the problematic deployment. With Q35 machines
unconditionally exposing a watchdog though, apps will think their
deployment is correct but in fact have no protection at all.
This patch flips the default of the second 'no reboot' flag, so that
configured watchdog actions will be honoured out of the box for the
7.2 Q35 machine type onwards, if the guest enables use of the watchdog.
See also related bug reports
https://bugzilla.redhat.com/show_bug.cgi?id=2080207https://bugzilla.redhat.com/show_bug.cgi?id=2136889https://bugzilla.redhat.com/show_bug.cgi?id=2137346
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-5-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can move setting default_cpu_version into the base machine options,
and we need to unset alias and is_default only once.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20221212152145.124317-3-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Add 8.0 machine types for arm/i440fx/m68k/q35/s390x/spapr.
Reviewed-by: Cédric Le Goater <clg@kaod.org> [ppc]
Reviewed-by: Thomas Huth <thuth@redhat.com> [s390x]
Reviewed-by: Greg Kurz <groug@kaod.org> [ppc]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20221212152145.124317-2-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The tracepoints aid in debugging the triggering of watchdog devices.
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-4-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These tracepoints aid in understanding and debugging the guest drivers
for the TCO watchdog.
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-3-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These tracepoints aid in understanding and debugging the guest drivers
for the TCO watchdog.
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221216125749.596075-2-berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When argument @error_status is symbolic, flag -c is ignored. Reject
it instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221201121133.3813857-14-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221201121133.3813857-13-armbru@redhat.com>
I'd like to use @err for an Error *err. Rename PCIEAERErr err to
aer_err.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221201121133.3813857-12-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221201121133.3813857-11-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221201121133.3813857-10-armbru@redhat.com>
PCI AER error status is 32 bit. The HMP command supports both
symbolic and numeric error status: anything that isn't a known
symbolic value is parsed as number with strtol(). Issues:
* Empty argument yields value zero.
* Range errors from strtol() are ignored, value is UINT32_MAX.
* Values not representable in uint32_t are silently truncated.
Fix to reject such input by switching to strtoui().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-9-armbru@redhat.com>
This method is for HMP command "info qtree".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221201121133.3813857-8-armbru@redhat.com>
pcibus_dev_print() contains a copy of get_class_desc(). Call the
function instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-7-armbru@redhat.com>
We compile pci-hmp-cmds.c always, but pci-qmp-cmds.c only when
CONFIG_PCI. hw/pci/pci-stub.c keeps the linker happy when
!CONFIG_PCI. Build pci-hmp-cmds.c that way, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-6-armbru@redhat.com>
QMP query-pci and HMP info pci can behave differently when there are
no PCI devices. They can report nothing, like this:
qemu-system-aarch64 -S -M spitz -display none -monitor stdio
QEMU 7.1.91 monitor - type 'help' for more information
(qemu) info pci
Or they can fail, like this:
qemu-system-microblaze -M petalogix-s3adsp1800 -display none -monitor stdio
QEMU 7.1.91 monitor - type 'help' for more information
(qemu) info pci
PCI devices not supported
They fail when none of the target's machines supports PCI, i.e. when
we're using qmp_query_pci() from hw/pci/pci-stub.c.
The error is not useful, and reporting nothing makes sense, so do that
in pci-stub.c, too.
Now qmp_query_pci() can't fail anymore. Drop the dead error handling
from hmp_info_pci().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221201121133.3813857-5-armbru@redhat.com>
This moves these commands from MAINTAINERS section "Human
Monitor (HMP)" to "PCI".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20221201121133.3813857-4-armbru@redhat.com>
This moves these commands from MAINTAINERS section "QMP" to "PCI".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221201121133.3813857-3-armbru@redhat.com>
[Commit message improved]
Fix a few style violations so that checkpatch.pl won't complain when I
move this code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221201121133.3813857-2-armbru@redhat.com>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY5rRbwAKCRBAov/yOSY+
3z9gA/4kVknTVNswOlcESvnjuTg0Qli6rWZy+Zjn6ZaqMFaHS3sWMEolOT1Dvtus
8iCKFS64224D0Lacf3aFeNlY2hmO65mcprgn04NxUWIxbgXQJg+fPmDfbQUNGJ1u
W+ylq855Ups7/gWXRsMNb1ZFllEyUu9KZxbEQS98FPc+2shU8w==
=+kWk
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20221215' of https://gitlab.com/gaosong/qemu into staging
Add cfi01 pflash device
# gpg: Signature made Thu 15 Dec 2022 07:49:03 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20221215' of https://gitlab.com/gaosong/qemu:
hw/loongarch/virt: Add cfi01 pflash device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the TYPE_PHB3_MSI class to 3-phase reset, so we can
avoid using the device_class_set_parent_reset() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-8-peter.maydell@linaro.org
Convert the TYPE_ICS class to 3-phase reset; this will allow us
to convert the TYPE_PHB3_MSI class which inherits from it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-7-peter.maydell@linaro.org
The realize method for the TYPE_ICS class uses qemu_register_reset()
to register a reset handler, as a workaround for the fact that
currently objects which directly inherit from TYPE_DEVICE don't get
automatically reset. However, the reset function directly calls
ics_reset(), which is the function that implements the legacy reset
method. This means that only the parent class's data gets reset, and
a subclass which also needs to handle reset, like TYPE_PHB3_MSI, has
to register its own reset function.
Make the TYPE_ICS reset function call device_cold_reset() instead:
this will handle reset for both the parent class and the subclass,
and will work whether the classes are using legacy reset or 3-phase
reset. This allows us to remove the reset function that the subclass
currently has to set up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-6-peter.maydell@linaro.org
Convert the TYPE_CXL_ROOT_PORT and TYPE_PNV_PHB_ROOT_PORT classes to
3-phase reset, so they don't need to use the deprecated
device_class_set_parent_reset() function any more.
We have to do both in the same commit, because they keep the
parent_reset field in their common parent class's class struct.
Note that pnv_phb_root_port_class_init() was pointlessly setting
dc->reset twice, once by calling device_class_set_parent_reset()
and once directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-5-peter.maydell@linaro.org
Convert the TYPE_PCIE_ROOT_PORT device to 3-phase reset; this is a
necessary precursor to converting any of its child classes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-4-peter.maydell@linaro.org
Convert the TYPE_VIRTIO_VGA_BASE class to 3-phase reset, so we
don't need to use device_class_set_parent_reset() any more.
Note that this is an abstract class itself; none of the subclasses
override its reset method.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-3-peter.maydell@linaro.org
Convert the TYPE_VIRTIO_PCI class to 3-phase reset. This is
necessary so that we can convert the subclass TYPE_VIRTIO_VGA_BASE
also to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-2-peter.maydell@linaro.org
Convert the parent class TYPE_CPU to 3-phase reset. This
is a necessary prerequisite to converting the subclasses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20221124115023.2437291-2-peter.maydell@linaro.org
Convert the various subclasses of TYPE_MOS6522 to 3-phase reset.
This removes some uses of device_class_set_parent_reset(), which we
would eventually like to be able to get rid of.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221110143459.3833425-3-peter.maydell@linaro.org
Convert the TYPE_MOS6522 parent class to use 3-phase reset. This is
a prerequisite for converting its subclasses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221110143459.3833425-2-peter.maydell@linaro.org
Convert the child classes TYPE_PS2_KBD_DEVICE and
TYPE_PS2_MOUSE_DEVICE to the 3-phase reset system. This allows us to
stop using the old device_class_set_parent_reset() function.
We don't need to register an 'exit' phase function for the
subclasses, because they have no work to do in that phase. Passing
NULL to resettable_class_set_parent_phases() will result in the
parent class method being called for that phase, so we don't need to
register a function purely to chain to the parent 'exit' phase
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109170009.3498451-3-peter.maydell@linaro.org
Convert the parent class TYPE_PS2_DEVICE to 3-phase reset. Note that
we need an 'exit' phase function as well as the usual 'hold' phase
function, because changing outbound IRQ line state is only permitted
in 'exit'. (Strictly speaking it's not supposed to be done in a
legacy reset handler either, but you can often get away with it.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109170009.3498451-2-peter.maydell@linaro.org
The device_legacy_reset() function is now not used anywhere, so we
can remove the implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the qdev_reset_all() and qbus_reset_all() functions, now we
have moved all the callers over to the new device_cold_reset() and
bus_cold_reset() functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The legacy function qdev_reset_all() performs a recursive reset,
starting from a qdev. However, it does not permit any of the devices
in the tree to use three-phase reset, because device reset goes
through the device_legacy_reset() function that only calls the single
DeviceClass::reset method.
Switch to using the device_cold_reset() function instead. This also
performs a recursive reset, where first the children are reset and
then finally the parent, but it uses the new (...in 2020...)
Resettable mechanism, which supports both the old style single-reset
method and also the new 3-phase reset handling.
This commit changes the five remaining uses of this function.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g' hw/i386/xen/xen_platform.c hw/input/adb.c hw/remote/vfio-user-obj.c hw/s390x/s390-virtio-ccw.c hw/usb/dev-uas.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the vmbus code we currently use the legacy functions
qdev_reset_all() and qbus_reset_all(). These perform a recursive
reset, starting from either a qbus or a qdev. However they do not
permit any of the devices in the tree to use three-phase reset,
because device reset goes through the device_legacy_reset() function
that only calls the single DeviceClass::reset method.
Switch to using the device_cold_reset() and bus_cold_reset()
functions. These also perform a recursive reset, where first the
children are reset and then finally the parent, but they use the new
(...in 2020...) Resettable mechanism, which supports both the old
style single-reset method and also the new 3-phase reset handling.
This should be a no-behaviour-change commit which just reduces the
use of a deprecated API.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g;s/qbus_reset_all/bus_cold_reset/g' hw/hyperv/*.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the PCI subsystem we currently use the legacy function
qdev_reset_all() and qbus_reset_all(). These perform a recursive
reset, starting from either a qbus or a qdev. However they do not
permit any of the devices in the tree to use three-phase reset,
because device reset goes through the device_legacy_reset() function
that only calls the single DeviceClass::reset method.
Switch to using the device_cold_reset() and bus_cold_reset()
functions. These also perform a recursive reset, where first the
children are reset and then finally the parent, but they use the new
(...in 2020...) Resettable mechanism, which supports both the old
style single-reset method and also the new 3-phase reset handling.
This should be a no-behaviour-change commit which just reduces the
use of a deprecated API.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g;s/qbus_reset_all/bus_cold_reset/g' hw/pci/*.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The semantic difference between the deprecated device_legacy_reset()
function and the newer device_cold_reset() function is that the new
function resets both the device itself and any qbuses it owns,
whereas the legacy function resets just the device itself and nothing
else.
In s390-pci-inst.c we use device_legacy_reset() to reset an
S390PCIBusDevice. This device doesn't have any child qbuses, so the
functions do the same thing and we can stop using the deprecated one.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix emulated MVCP and MVCS s390x instructions
* Clean-ups for the e1000e qtest
* Enable qtests on Windows
* Update FreeBSD CI to version 12.4
* Check --disable-tcg for ppc64 in the CI
* Improve scripts/make-releases a little bit
* Many other misc small clean-ups and fixes here and there
-----BEGIN PGP SIGNATURE-----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=u/jz
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2022-12-15' of https://gitlab.com/thuth/qemu into staging
* s390x PCI fixes and improvements (for the ISM device)
* Fix emulated MVCP and MVCS s390x instructions
* Clean-ups for the e1000e qtest
* Enable qtests on Windows
* Update FreeBSD CI to version 12.4
* Check --disable-tcg for ppc64 in the CI
* Improve scripts/make-releases a little bit
* Many other misc small clean-ups and fixes here and there
# gpg: Signature made Thu 15 Dec 2022 15:05:44 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-12-15' of https://gitlab.com/thuth/qemu: (23 commits)
tests/qtest/vhost-user-blk-test: don't abort all qtests on missing envar
.gitlab/issue_templates: Move suggestions into comments
gitlab-ci: Check building ppc64 without TCG
FreeBSD: Upgrade to 12.4 release
tests/qtest: Enable qtest build on Windows
.gitlab-ci.d/windows.yml: Exclude qTests from 64-bit CI job for now
.gitlab-ci.d/windows.yml: Keep 64-bit and 32-bit build scripts consistent
.gitlab-ci.d/windows.yml: Unify the prerequisite packages
tests/qtest/libqos/e1000e: Correctly group register accesses
tests/qtest/e1000e-test: De-duplicate constants
tests/qtest/libqos/e1000e: Remove "other" interrupts
hw: Include the VMWare devices only in the x86 targets
MAINTAINERS: Add documentation files to the corresponding sections
util/oslib-win32: Remove obsolete reference to g_poll code
util/qemu-config: Fix "query-command-line-options" to provide the right values
scripts/make-release: Only clone single branches to speed up the script
scripts/make-release: Add a simple help text for the script
monitor/misc: Remove superfluous include statements
target/s390x: The MVCP and MVCS instructions are not privileged
target/s390x/tcg/mem_helper: Test the right bits in psw_key_valid()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* hw/arm/virt: Add properties to allow more granular
configuration of use of highmem space
* target/arm: Add Cortex-A55 CPU
* hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
* Implement FEAT_EVT
* Some 3-phase-reset conversions for Arm GIC, SMMU
* hw/arm/boot: set initrd with #address-cells type in fdt
* hw/misc: Move some arm-related files from specific_ss into softmmu_ss
* Restrict arm_cpu_exec_interrupt() to TCG accelerator
-----BEGIN PGP SIGNATURE-----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=YAjF
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20221215-1' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* hw/arm/virt: Add properties to allow more granular
configuration of use of highmem space
* target/arm: Add Cortex-A55 CPU
* hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
* Implement FEAT_EVT
* Some 3-phase-reset conversions for Arm GIC, SMMU
* hw/arm/boot: set initrd with #address-cells type in fdt
* hw/misc: Move some arm-related files from specific_ss into softmmu_ss
* Restrict arm_cpu_exec_interrupt() to TCG accelerator
# gpg: Signature made Thu 15 Dec 2022 17:38:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20221215-1' of https://git.linaro.org/people/pmaydell/qemu-arm: (28 commits)
target/arm: Restrict arm_cpu_exec_interrupt() to TCG accelerator
hw/misc: Move some arm-related files from specific_ss into softmmu_ss
hw/arm/boot: set initrd with #address-cells type in fdt
hw/intc: Convert TYPE_KVM_ARM_ITS to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_ITS to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_ITS_COMMON to 3-phase reset
hw/intc: Convert TYPE_KVM_ARM_GICV3 to 3-phase reset
hw/intc: Convert TYPE_ARM_GICV3_COMMON to 3-phase reset
hw/intc: Convert TYPE_ARM_GIC_KVM to 3-phase reset
hw/intc: Convert TYPE_ARM_GIC_COMMON to 3-phase reset
hw/arm: Convert TYPE_ARM_SMMUV3 to 3-phase reset
hw/arm: Convert TYPE_ARM_SMMU to 3-phase reset
target/arm: Report FEAT_EVT for TCG '-cpu max'
target/arm: Implement HCR_EL2.TID4 traps
target/arm: Implement HCR_EL2.TICAB,TOCU traps
target/arm: Implement HCR_EL2.TTLBOS traps
target/arm: Implement HCR_EL2.TTLBIS traps
target/arm: Allow relevant HCR bits to be written for FEAT_EVT
hw/intc/arm_gicv3: Fix GICD_TYPER ITLinesNumber advertisement
target/arm: Add Cortex-A55 CPU
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The header target/arm/kvm-consts.h checks CONFIG_KVM which is marked as
poisoned in common code, so the files that include this header have to
be added to specific_ss and recompiled for each, qemu-system-arm and
qemu-system-aarch64. However, since the kvm headers are only optionally
used in kvm-constants.h for some sanity checks, we can additionally
check the NEED_CPU_H macro first to avoid the poisoned CONFIG_KVM macro,
so kvm-constants.h can also be used from "common" files (without the
sanity checks - which should be OK since they are still done from other
target-specific files instead). This way, and by adjusting some other
include statements in the related files here and there, we can move some
files from specific_ss into softmmu_ss, so that they only need to be
compiled once during the build process.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221202154023.293614-1-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It seems a little bit weird that the para-virtualized x86 VMWare
devices "vmware-svga" and "vmxnet3" also show up in non-x86 targets.
They are likely pretty useless there (since the guest OSes likely
do not have any drivers for those enabled), so let's change this and
only enable those devices by default for the classical x86 targets.
Message-Id: <20221213095144.42355-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ISM device firmware stores unique state information that can
can cause a wholesale unmap of the associated IOMMU (e.g. when
we get a termination signal for QEMU) to trigger firmware errors
because firmware believes we are attempting to invalidate entries
that are still in-use by the guest OS (when in fact that guest is
in the process of being terminated or rebooted).
To alleviate this, register both a shutdown notifier (for unexpected
termination cases e.g. virsh destroy) as well as a reset callback
(for cases like guest OS reboot). For each of these scenarios, trigger
PCI device reset; this is enough to indicate to firmware that the IOMMU
is no longer in-use by the guest OS, making it safe to invalidate any
associated IOMMU entries.
Fixes: 15d0e7942d ("s390x/pci: don't fence interpreted devices without MSI-X")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20221209195700.263824-1-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
[thuth: Adjusted the hunk in s390-pci-vfio.c due to different context]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently, s390x-pci performs accounting against the vfio DMA
limit and triggers the guest to clean up mappings when the limit
is reached. Let's go a step further and also limit the size of
the supported DMA aperture reported to the guest based upon the
initial vfio DMA limit reported for the container (if less than
than the size reported by the firmware/host zPCI layer). This
avoids processing sections of the guest DMA table during global
refresh that, for common use cases, will never be used anway, and
makes exhausting the vfio DMA limit due to mismatch between guest
aperture size and host limit far less likely and more indicitive
of an error.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20221028194758.204007-4-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently, each unmapped page is handled as an individual iommu
region notification. Attempt to group contiguous unmap operations
into fewer notifications to reduce overhead.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-Id: <20221028194758.204007-3-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We use 32bit value for linux,initrd-[start/end], when we have
loader_start > 4GB, there will be a wrong initrd_start passed
to the kernel, and the kernel will report the following warning.
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] initrd not fully accessible via the linear mapping -- please check your bootloader ...
[ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm64/mm/init.c:355 arm64_memblock_init+0x158/0x244
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Tainted: G W 6.1.0-rc3-13250-g30a0b95b1335-dirty #28
[ 0.000000] Hardware name: Horizon Sigi Virtual development board (DT)
[ 0.000000] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.000000] pc : arm64_memblock_init+0x158/0x244
[ 0.000000] lr : arm64_memblock_init+0x158/0x244
[ 0.000000] sp : ffff800009273df0
[ 0.000000] x29: ffff800009273df0 x28: 0000001000cc0010 x27: 0000800000000000
[ 0.000000] x26: 000000000050a3e2 x25: ffff800008b46000 x24: ffff800008b46000
[ 0.000000] x23: ffff800008a53000 x22: ffff800009420000 x21: ffff800008a53000
[ 0.000000] x20: 0000000004000000 x19: 0000000004000000 x18: 00000000ffff1020
[ 0.000000] x17: 6568632065736165 x16: 6c70202d2d20676e x15: 697070616d207261
[ 0.000000] x14: 656e696c20656874 x13: 0a2e2e2e20726564 x12: 0000000000000000
[ 0.000000] x11: 0000000000000000 x10: 00000000ffffffff x9 : 0000000000000000
[ 0.000000] x8 : 0000000000000000 x7 : 796c6c756620746f x6 : 6e20647274696e69
[ 0.000000] x5 : ffff8000093c7c47 x4 : ffff800008a2102f x3 : ffff800009273a88
[ 0.000000] x2 : 80000000fffff038 x1 : 00000000000000c0 x0 : 0000000000000056
[ 0.000000] Call trace:
[ 0.000000] arm64_memblock_init+0x158/0x244
[ 0.000000] setup_arch+0x164/0x1cc
[ 0.000000] start_kernel+0x94/0x4ac
[ 0.000000] __primary_switched+0xb4/0xbc
[ 0.000000] ---[ end trace 0000000000000000 ]---
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000001000000000-0x0000001007ffffff]
This doesn't affect any machine types we currently support, because
for all of our machine types the RAM starts well below the 4GB
mark, but it does demonstrate that we're not currently writing
the device-tree properties quite as intended.
To fix it, we can change it to write these values to the dtb using a
type width matching #address-cells. This is the intended size for
these dtb properties, and is how u-boot, for instance, writes them,
although in practice the Linux kernel will cope with them being any
width as long as they're big enough to fit the value.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Message-id: 20221129160724.75667-1-schspa@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the TYPE_KVM_ARM_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-10-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-9-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-8-peter.maydell@linaro.org
Convert the TYPE_KVM_ARM_GICV3 device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-7-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-6-peter.maydell@linaro.org
Now we have converted TYPE_ARM_GIC_COMMON, we can convert the
TYPE_ARM_GIC_KVM subclass to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-5-peter.maydell@linaro.org
Convert the TYPE_ARM_GIC_COMMON device to 3-phase reset. This is a
simple no-behaviour-change conversion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-4-peter.maydell@linaro.org
Convert the TYPE_ARM_SMMUV3 device to 3-phase reset. The legacy
reset method doesn't do anything that's invalid in the hold phase, so
the conversion only requires changing it to a hold phase method, and
using the 3-phase versions of the "save the parent reset method and
chain to it" code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-3-peter.maydell@linaro.org
Convert the TYPE_ARM_SMMU device to 3-phase reset. The legacy method
doesn't do anything that's invalid in the hold phase, so the
conversion is simple and not a behaviour change.
Note that we must convert this base class before we can convert the
TYPE_ARM_SMMUV3 subclass -- transitional support in Resettable
handles "chain to parent class reset" when the base class is 3-phase
and the subclass is still using legacy reset, but not the other way
around.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221109161444.3397405-2-peter.maydell@linaro.org
The ARM GICv3 TRM describes that the ITLinesNumber field of GICD_TYPER
register:
"indicates the maximum SPI INTID that the GIC implementation supports"
As SPI #0 is absolute IRQ #32, the max SPI INTID should have accounted
for the internal 16x SGI's and 16x PPI's. However, the original GICv3
model subtracted off the SGI/PPI. Cosmetically this can be seen at OS
boot (Linux) showing 32 shy of what should be there, i.e.:
[ 0.000000] GICv3: 224 SPIs implemented
Though in hw/arm/virt.c, the machine is configured for 256 SPI's. ARM
virt machine likely doesn't have a problem with this because the upper
32 IRQ's don't actually have anything meaningful wired. But, this does
become a functional issue on a custom use case which wants to make use
of these IRQ's. Additionally, boot code (i.e. TF-A) will only init up
to the number (blocks of 32) that it believes to actually be there.
Signed-off-by: Luke Starrett <lukes@xsightlabs.com>
Message-id: AM9P193MB168473D99B761E204E032095D40D9@AM9P193MB1684.EURP193.PROD.OUTLOOK.COM
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-A55 is one of the newer armv8.2+ CPUs; in particular
it supports the Privileged Access Never (PAN) feature. Add
a model of this CPU, so you can use a CPU type on the virt
board that models a specific real hardware CPU, rather than
having to use the QEMU-specific "max" CPU type.
Signed-off-by: Timofey Kutergin <tkutergin@gmail.com>
Message-id: 20221121150819.2782817-1-tkutergin@gmail.com
[PMM: tweaked commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the base_memmap to build the SMBIOS 19 table which provides the address
mapping for a Physical Memory Array (from spec [1] chapter 7.20).
This was present on i386 from commit c97294ec1b
("SMBIOS: Build aggregate smbios tables and entry point").
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.5.0.pdf
The absence of this table is a breach of the specs and is
detected by the FirmwareTestSuite (FWTS), but it doesn't
cause any known problems for guest OSes.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Message-id: 1668789029-5432-1-git-send-email-mihai.carabas@oracle.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 3 high memory regions are usually enabled by default, but they may
be not used. For example, VIRT_HIGH_GIC_REDIST2 isn't needed by GICv2.
This leads to waste in the PA space.
Add properties ("highmem-redists", "highmem-ecam", "highmem-mmio") to
allow users selectively disable them if needed. After that, the high
memory region for GICv3 or GICv4 redistributor can be disabled by user,
the number of maximal supported CPUs needs to be calculated based on
'vms->highmem_redists'. The follow-up error message is also improved
to indicate if the high memory region for GICv3 and GICv4 has been
enabled or not.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20221029224307.138822-8-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After the improvement to high memory region address assignment is
applied, the memory layout can be changed, introducing possible
migration breakage. For example, VIRT_HIGH_PCIE_MMIO memory region
is disabled or enabled when the optimization is applied or not, with
the following configuration. The configuration is only achievable by
modifying the source code until more properties are added to allow
users selectively disable those high memory regions.
pa_bits = 40;
vms->highmem_redists = false;
vms->highmem_ecam = false;
vms->highmem_mmio = true;
# qemu-system-aarch64 -accel kvm -cpu host \
-machine virt-7.2,compact-highmem={on, off} \
-m 4G,maxmem=511G -monitor stdio
Region compact-highmem=off compact-highmem=on
----------------------------------------------------------------
MEM [1GB 512GB] [1GB 512GB]
HIGH_GIC_REDISTS2 [512GB 512GB+64MB] [disabled]
HIGH_PCIE_ECAM [512GB+256MB 512GB+512MB] [disabled]
HIGH_PCIE_MMIO [disabled] [512GB 1TB]
In order to keep backwords compatibility, we need to disable the
optimization on machine, which is virt-7.1 or ealier than it. It
means the optimization is enabled by default from virt-7.2. Besides,
'compact-highmem' property is added so that the optimization can be
explicitly enabled or disabled on all machine types by users.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-7-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are three high memory regions, which are VIRT_HIGH_REDIST2,
VIRT_HIGH_PCIE_ECAM and VIRT_HIGH_PCIE_MMIO. Their base addresses
are floating on highest RAM address. However, they can be disabled
in several cases.
(1) One specific high memory region is likely to be disabled by
code by toggling vms->highmem_{redists, ecam, mmio}.
(2) VIRT_HIGH_PCIE_ECAM region is disabled on machine, which is
'virt-2.12' or ealier than it.
(3) VIRT_HIGH_PCIE_ECAM region is disabled when firmware is loaded
on 32-bits system.
(4) One specific high memory region is disabled when it breaks the
PA space limit.
The current implementation of virt_set_{memmap, high_memmap}() isn't
optimized because the high memory region's PA space is always reserved,
regardless of whatever the actual state in the corresponding
vms->highmem_{redists, ecam, mmio} flag. In the code, 'base' and
'vms->highest_gpa' are always increased for case (1), (2) and (3).
It's unnecessary since the assigned PA space for the disabled high
memory region won't be used afterwards.
Improve the address assignment for those three high memory region by
skipping the address assignment for one specific high memory region if
it has been disabled in case (1), (2) and (3). The memory layout may
be changed after the improvement is applied, which leads to potential
migration breakage. So 'vms->highmem_compact' is added to control if
the improvement should be applied. For now, 'vms->highmem_compact' is
set to false, meaning that we don't have memory layout change until it
becomes configurable through property 'compact-highmem' in next patch.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_get_high_memmap_enabled() helper, which returns
the pointer to vms->highmem_{redists, ecam, mmio}. The pointer will
be used in the subsequent patches.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-5-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces variable 'region_base' for the base address of the
specific high memory region. It's the preparatory work to optimize
high memory region address assignment.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This renames variable 'size' to 'region_size' in virt_set_high_memmap().
Its counterpart ('region_base') will be introduced in next patch.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces virt_set_high_memmap() helper. The logic of high
memory region address assignment is moved to the helper. The intention
is to make the subsequent optimization for high memory region address
assignment easier.
No functional change intended.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Message-id: 20221029224307.138822-2-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=JJjG
-----END PGP SIGNATURE-----
Merge tag 'pull-misc-2022-12-14' of https://repo.or.cz/qemu/armbru into staging
Miscellaneous patches for 2022-12-14
# gpg: Signature made Wed 14 Dec 2022 15:23:02 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* tag 'pull-misc-2022-12-14' of https://repo.or.cz/qemu/armbru:
ppc4xx_sdram: Simplify sdram_ddr_size() to return
block/vmdk: Simplify vmdk_co_create() to return directly
cleanup: Tweak and re-run return_directly.cocci
io: Tidy up fat-fingered parameter name
qapi: Use returned bool to check for failure (again)
sockets: Use ERRP_GUARD() where obviously appropriate
qemu-config: Use ERRP_GUARD() where obviously appropriate
qemu-config: Make config_parse_qdict() return bool
monitor: Use ERRP_GUARD() in monitor_init()
monitor: Simplify monitor_fd_param()'s error handling
error: Move ERRP_GUARD() to the beginning of the function
error: Drop a few superfluous ERRP_GUARD()
error: Drop some obviously superfluous error_propagate()
Drop more useless casts from void * to pointer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/virtio.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-29-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/rocker.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-23-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/qdev.json and
qapi/qom.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Cc: Eduardo Habkost <eduardo@habkost.net>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-21-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/pci.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221104160712.3005652-20-armbru@redhat.com>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/net.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[Fixes for MacOS squashed in]
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/machine*.json.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Eduardo Habkost <eduardo@habkost.net>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221104160712.3005652-16-armbru@redhat.com>
Tweak the semantic patch to drop redundant parenthesis around the
return expression.
Coccinelle drops a comment in hw/rdma/vmw/pvrdma_cmd.c; restored
manually.
Coccinelle messes up vmdk_co_create(), not sure why. Change dropped,
will be done manually in the next commit.
Line breaks in target/avr/cpu.h and hw/rdma/vmw/pvrdma_cmd.c tidied up
manually.
Whitespace in tools/virtiofsd/fuse_lowlevel.c tidied up manually.
checkpatch.pl complains "return of an errno should typically be -ve"
two times for hw/9pfs/9p-synth.c. Preexisting, the patch merely makes
it visible to checkpatch.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221122134917.1217307-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 012d4c96e2 changed the visitor functions taking Error ** to
return bool instead of void, and the commits following it used the new
return value to simplify error checking. Since then a few more uses
in need of the same treatment crept in. Do that. All pretty
mechanical except for
* balloon_stats_get_all()
This is basically the same transformation commit 012d4c96e2 applied
to the virtual walk example in include/qapi/visitor.h.
* set_max_queue_size()
Additionally replace "goto end of function" by return.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
include/qapi/error.h advises to put ERRP_GUARD() right at the
beginning of the function, because only then can it guard the whole
function. Clean up the few spots disregarding the advice.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
include/qapi/error.h on ERRP_GUARD():
* It must be used when the function dereferences @errp or passes
* @errp to error_prepend(), error_vprepend(), or error_append_hint().
* It is safe to use even when it's not needed, but please avoid
* cluttering the source with useless code.
Clean up some of this clutter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-3-armbru@redhat.com>
When error_propagate(errp, local_err) is the only reader of
@local_err, we can just as well change its writers to write @errp
directly, and drop the error_propagate() along with @local_err.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221121085054.683122-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The has_FOO for pointer-valued FOO are redundant, except for arrays.
They are also a nuisance to work with. Recent commit "qapi: Start to
elide redundant has_FOO in generated C" provided the means to elide
them step by step. This is the step for qapi/acpi.py.
Said commit explains the transformation in more detail. The invariant
violations mentioned there do not occur here.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20221104160712.3005652-7-armbru@redhat.com>
This reverts commit 14dccc8ea6.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221205113007.683505-1-gaosong@loongson.cn>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY4nPggAKCRBAov/yOSY+
36cRA/9JFWuDT0TDhu0g1x0ktvpV+1GBPzkEXR2CVhDf2bly1ka2cLEtPUpiSE8E
Osw9cEBR3qX+LyO3gA0GySUr9jsc/yRqD38OL8HGZTCmZ/qCnHJSXvy+6a0LWYQq
ZIrFat7UjiTTeErkSQ6C4bUIl6YoUUSP0X2XxO6YF5j4uhGyqA==
=sVrx
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20221202' of https://gitlab.com/gaosong/qemu into staging
pull for 7.2-rc4
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY4nPggAKCRBAov/yOSY+
# 36cRA/9JFWuDT0TDhu0g1x0ktvpV+1GBPzkEXR2CVhDf2bly1ka2cLEtPUpiSE8E
# Osw9cEBR3qX+LyO3gA0GySUr9jsc/yRqD38OL8HGZTCmZ/qCnHJSXvy+6a0LWYQq
# ZIrFat7UjiTTeErkSQ6C4bUIl6YoUUSP0X2XxO6YF5j4uhGyqA==
# =sVrx
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 02 Dec 2022 05:12:18 EST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20221202' of https://gitlab.com/gaosong/qemu:
hw/loongarch/virt: Add cfi01 pflash device
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* fixes for aio cancellation in commands that may issue several
aios
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmOI2uQACgkQTeGvMW1P
Dem6nQgAi8Dm0vhRLoEHqT6FG+VBy0Evpw2QThGE8PxsfzJ1nlwXt6s/NwEc10Uc
d5exp6AR9p37dGJfH82y8EYdEgMeJfsKQRDVMUR4n7eEOW+/Sp4WicO7iamEIWhr
CgRBw1aqU7Im0CHn+3nXu0LKXEtT+tOQrfnr255ELzCxKPZuP3Iw/+nzLQij1G4N
9D9FPPyec+blz+0HuRg12m1ri6TAb2k9CuODuZrqLDCW8Hnl1MVmmYGZrYBy9sPr
Q2zohAjad6R5/+4BCAlusbQ0deoXYKOJdb8J2A9EN73maSqjsHQAagfs+kKxAQK4
ttiy/M/l5EGJG496rZfUJZCnVlOllQ==
=Blzi
-----END PGP SIGNATURE-----
Merge tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme into staging
hw/nvme fixes
* fixes for aio cancellation in commands that may issue several
aios
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmOI2uQACgkQTeGvMW1P
# Dem6nQgAi8Dm0vhRLoEHqT6FG+VBy0Evpw2QThGE8PxsfzJ1nlwXt6s/NwEc10Uc
# d5exp6AR9p37dGJfH82y8EYdEgMeJfsKQRDVMUR4n7eEOW+/Sp4WicO7iamEIWhr
# CgRBw1aqU7Im0CHn+3nXu0LKXEtT+tOQrfnr255ELzCxKPZuP3Iw/+nzLQij1G4N
# 9D9FPPyec+blz+0HuRg12m1ri6TAb2k9CuODuZrqLDCW8Hnl1MVmmYGZrYBy9sPr
# Q2zohAjad6R5/+4BCAlusbQ0deoXYKOJdb8J2A9EN73maSqjsHQAagfs+kKxAQK4
# ttiy/M/l5EGJG496rZfUJZCnVlOllQ==
# =Blzi
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Dec 2022 11:48:36 EST
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* tag 'nvme-next-pull-request' of git://git.infradead.org/qemu-nvme:
hw/nvme: remove copy bh scheduling
hw/nvme: fix aio cancel in dsm
hw/nvme: fix aio cancel in zone reset
hw/nvme: fix aio cancel in flush
hw/nvme: fix aio cancel in format
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Fixes regression with migration and vsock, as fixing that
exposes some known issues in vhost user cleanup, this attempts
to fix those as well. More work on vhost user is needed :)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmOIWaEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp+RQH/2PVAjD/GA3zF5F3Z07vH51c55T6tluZ85c3
4u66SSkF5JR1hATCujYCtrt9V0mnqhmhhm4gJH5xcsynFjjyIXd2dDrTFRpCtRgn
icXOmYCc9pCu8XsluJnWvY/5r/KEDxqmGVE8Kyhz551QjvsBkezhI9x9vhJZJLCn
Xn1XQ/3jpUcQLwasu8AxZb0IDW8WdCtonbke6xIyMzOYGR2bnRdXlDXVVG1zJ/SZ
eS3HUad71VekhfzWq0fx8yEJnfvbes9vo007y8rOGdHOcMneWGAie52W1dOBhclh
Zt56zID55t1USEwlPxkZSj7UXNbVl7Uz/XU5ElN0yTesttP4Iq0=
=ZkaX
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio: regression fix
Fixes regression with migration and vsock, as fixing that
exposes some known issues in vhost user cleanup, this attempts
to fix those as well. More work on vhost user is needed :)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmOIWaEPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp+RQH/2PVAjD/GA3zF5F3Z07vH51c55T6tluZ85c3
# 4u66SSkF5JR1hATCujYCtrt9V0mnqhmhhm4gJH5xcsynFjjyIXd2dDrTFRpCtRgn
# icXOmYCc9pCu8XsluJnWvY/5r/KEDxqmGVE8Kyhz551QjvsBkezhI9x9vhJZJLCn
# Xn1XQ/3jpUcQLwasu8AxZb0IDW8WdCtonbke6xIyMzOYGR2bnRdXlDXVVG1zJ/SZ
# eS3HUad71VekhfzWq0fx8yEJnfvbes9vo007y8rOGdHOcMneWGAie52W1dOBhclh
# Zt56zID55t1USEwlPxkZSj7UXNbVl7Uz/XU5ElN0yTesttP4Iq0=
# =ZkaX
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Dec 2022 02:37:05 EST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
include/hw: VM state takes precedence in virtio_device_should_start
hw/virtio: generalise CHR_EVENT_CLOSED handling
hw/virtio: add started_vu status field to vhost-user-gpio
vhost: enable vrings in vhost_dev_start() for vhost-user devices
tests/qtests: override "force-legacy" for gpio virtio-mmio tests
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Fix a potential use-after-free by removing the bottom half and enqueuing
the completion directly.
Fixes: 796d20681d ("hw/nvme: reimplement the copy command to allow aio cancellation")
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
When the DSM operation is cancelled asynchronously, we set iocb->ret to
-ECANCELED. However, the callback function only checks the return value
of the completed aio, which may have completed succesfully prior to the
cancellation and thus the callback ends up continuing the dsm operation
instead of bailing out. Fix this.
Secondly, fix a potential use-after-free by removing the bottom half and
enqueuing the completion directly.
Fixes: d7d1474fd8 ("hw/nvme: reimplement dsm to allow cancellation")
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If the zone reset operation is cancelled but the block unmap operation
completes normally, the callback will continue resetting the next zone
since it neglects to check iocb->ret which will have been set to
-ECANCELED. Make sure that this is checked and bail out if an error is
present.
Secondly, fix a potential use-after-free by removing the bottom half and
enqueuing the completion directly.
Fixes: 63d96e4ffd ("hw/nvme: reimplement zone reset to allow cancellation")
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Make sure that iocb->aiocb is NULL'ed when cancelling.
Fix a potential use-after-free by removing the bottom half and enqueuing
the completion directly.
Fixes: 38f4ac65ac ("hw/nvme: reimplement flush to allow cancellation")
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There are several bugs in the async cancel code for the Format command.
Firstly, cancelling a format operation neglects to set iocb->ret as well
as clearing the iocb->aiocb after cancelling the underlying aiocb which
causes the aio callback to ignore the cancellation. Trivial fix.
Secondly, and worse, because the request is queued up for posting to the
CQ in a bottom half, if the cancellation is due to the submission queue
being deleted (which calls blk_aio_cancel), the req structure is
deallocated in nvme_del_sq prior to the bottom half being schedulued.
Fix this by simply removing the bottom half, there is no reason to defer
it anyway.
Fixes: 3bcf26d3d6 ("hw/nvme: reimplement format nvm to allow cancellation")
Reported-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
..and use for both virtio-user-blk and virtio-user-gpio. This avoids
the circular close by deferring shutdown due to disconnection until a
later point. virtio-user-blk already had this mechanism in place so
generalise it as a vhost-user helper function and use for both blk and
gpio devices.
While we are at it we also fix up vhost-user-gpio to re-establish the
event handler after close down so we can reconnect later.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20221130112439.2527228-5-alex.bennee@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As per the fix to vhost-user-blk in f5b22d06fb (vhost: recheck dev
state in the vhost_migration_log routine) we really should track the
connection and starting separately.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221130112439.2527228-4-alex.bennee@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 02b61f38d3 ("hw/virtio: incorporate backend features in features")
properly negotiates VHOST_USER_F_PROTOCOL_FEATURES with the vhost-user
backend, but we forgot to enable vrings as specified in
docs/interop/vhost-user.rst:
If ``VHOST_USER_F_PROTOCOL_FEATURES`` has not been negotiated, the
ring starts directly in the enabled state.
If ``VHOST_USER_F_PROTOCOL_FEATURES`` has been negotiated, the ring is
initialized in a disabled state and is enabled by
``VHOST_USER_SET_VRING_ENABLE`` with parameter 1.
Some vhost-user front-ends already did this by calling
vhost_ops.vhost_set_vring_enable() directly:
- backends/cryptodev-vhost.c
- hw/net/virtio-net.c
- hw/virtio/vhost-user-gpio.c
But most didn't do that, so we would leave the vrings disabled and some
backends would not work. We observed this issue with the rust version of
virtiofsd [1], which uses the event loop [2] provided by the
vhost-user-backend crate where requests are not processed if vring is
not enabled.
Let's fix this issue by enabling the vrings in vhost_dev_start() for
vhost-user front-ends that don't already do this directly. Same thing
also in vhost_dev_stop() where we disable vrings.
[1] https://gitlab.com/virtio-fs/virtiofsd
[2] https://github.com/rust-vmm/vhost/blob/240fc2966/crates/vhost-user-backend/src/event_loop.rs#L217
Fixes: 02b61f38d3 ("hw/virtio: incorporate backend features in features")
Reported-by: German Maglione <gmaglione@redhat.com>
Tested-by: German Maglione <gmaglione@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20221123131630.52020-1-sgarzare@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20221130112439.2527228-3-alex.bennee@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20221128202741.4945-6-philmd@linaro.org>
