it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dongjiu Geng <gengdongjiu1@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
While at it switch to build_append_int_noprefix() to build
entries to other tables (which also removes some manual offset
calculations).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offests magic from API user.
While at it switch to build_append_int_noprefix() to build
entries to other tables (which also removes some manual offset
calculations).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Patch introduces acpi_table_begin()/ acpi_table_end() API
that hides pointer/offset arithmetic from user as opposed
to build_header(), to prevent errors caused by it [1].
acpi_table_begin():
initializes table header and keeps track of
table data/offsets
acpi_table_end():
sets actual table length and tells bios loader
where table is for the later initialization on
guest side.
1) commits
bb9feea431 x86: acpi: use offset instead of pointer when using build_header()
4d027afeb3 Virt: ACPI: fix qemu assert due to re-assigned table data address
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
virtio-vsock features, like VIRTIO_VSOCK_F_SEQPACKET, can be handled
by vhost-vsock-common parent class. In this way, we can reuse the
same code for all virtio-vsock backends (i.e. vhost-vsock,
vhost-user-vsock).
Let's move `seqpacket` property to vhost-vsock-common class, add
vhost_vsock_common_get_features() used by children, and disable
`seqpacket` for vhost-user-vsock device for machine types < 6.2.
The behavior of vhost-vsock device doesn't change; vhost-user-vsock
device now supports `seqpacket` property.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210921161642.206461-3-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 1e08fd0a46 ("vhost-vsock: SOCK_SEQPACKET feature bit support")
enabled the SEQPACKET feature bit.
This commit is released with QEMU 6.1, so if we try to migrate a VM where
the host kernel supports SEQPACKET but machine type version is less than
6.1, we get the following errors:
Features 0x130000002 unsupported. Allowed features: 0x179000000
Failed to load virtio-vhost_vsock:virtio
error while loading state for instance 0x0 of device '0000:00:05.0/virtio-vhost_vsock'
load of migration failed: Operation not permitted
Let's disable the feature bit for machine types < 6.1.
We add a new OnOffAuto property for this, called `seqpacket`.
When it is `auto` (default), QEMU behaves as before, trying to enable the
feature, when it is `on` QEMU will fail if the backend (vhost-vsock
kernel module) doesn't support it.
Fixes: 1e08fd0a46 ("vhost-vsock: SOCK_SEQPACKET feature bit support")
Cc: qemu-stable@nongnu.org
Reported-by: Jiang Wang <jiang.wang@bytedance.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210921161642.206461-2-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both virtqueue_packed_get_avail_bytes() and
virtqueue_split_get_avail_bytes() access the region cache, but
their caller also does. Simplify by having virtqueue_get_avail_bytes
calling both with RCU lock held, and passing the caches as argument.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210906104318.1569967-4-philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
vring_get_region_caches() must be called with the RCU read lock
acquired. virtqueue_packed_drop_all() does not, and uses the
'caches' pointer. Fix that by using the RCU_READ_LOCK_GUARD()
macro.
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210906104318.1569967-3-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
If SEV is enabled and a kernel is passed via -kernel, pass the hashes of
kernel/initrd/cmdline in an encrypted guest page to OVMF for SEV
measured boot.
Co-developed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Dov Murik <dovmurik@linux.ibm.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210930054915.13252-3-dovmurik@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We might not start at the beginning of the memory region. Let's
calculate the offset into the memory region via the difference in the
host addresses.
Acked-by: Stefan Berger <stefanb@linux.ibm.com>
Fixes: ffab1be706 ("tpm: clear RAM when "memory overwrite" requested")
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Claudio Fontana <cfontana@suse.de>
Cc: Thomas Huth <thuth@redhat.com>
Cc: "Alex Bennée" <alex.bennee@linaro.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210727082545.17934-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As we might not always have a device id, it is impossible to always
match MEMORY_DEVICE_SIZE_CHANGE events to an actual device. Let's
include the qom-path in the event, which allows for reliable mapping of
events to devices.
Fixes: 722a3c783e ("virtio-pci: Send qapi events when the virtio-mem size changes")
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210929162445.64060-3-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Apparently, we don't have to duplicate the string.
Fixes: 722a3c783e ("virtio-pci: Send qapi events when the virtio-mem size changes")
Cc: qemu-stable@nongnu.org
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210929162445.64060-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM implements some Hyper-V 2016 functions so providing WS2008R2 version
is somewhat incorrect. While generally guests shouldn't care about it
and always check feature bits, it is known that some tools in Windows
actually check version info.
For compatibility reasons make the change for 6.2 machine types only.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210902093530.345756-9-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Put both sanity-check of the input SMP configuration and sanity-check
of the output SMP configuration uniformly in the generic parser. Then
machine_set_smp() will become cleaner, also all the invalid scenarios
can be tested only by calling the parser.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-16-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we have a common structure SMPCompatProps used to store information
about SMP compatibility stuff, so we can also move smp_prefer_sockets
there for cleaner code.
No functional change intended.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-15-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now we have a generic smp parser for all arches, and there will
not be any other arch specific ones, so let's remove the callback
from MachineClass and call the parser directly.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-14-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently the only difference between smp_parse and pc_smp_parse
is the support of dies parameter and the related error reporting.
With some arch compat variables like "bool dies_supported", we can
make smp_parse generic enough for all arches and the PC specific
one can be removed.
Making smp_parse() generic enough can reduce code duplication and
ease the code maintenance, and also allows extending the topology
with more arch specific members (e.g., clusters) in the future.
Suggested-by: Andrew Jones <drjones@redhat.com>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-13-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all the possible topology parameters are integrated in struct
CpuTopology, tweak the order of topology members to be "cpus/sockets/
dies/cores/threads/maxcpus" for readability and consistency. We also
tweak the comment by adding explanation of dies parameter.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210929025816.21076-12-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the sanity-check of smp_cpus and max_cpus against mc in function
machine_set_smp(), we are now using ms->smp.max_cpus for the check
but using current_machine->smp.max_cpus in the error message.
Tweak this by uniformly using the local ms.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210929025816.21076-11-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the real SMP hardware topology world, it's much more likely that
we have high cores-per-socket counts and few sockets totally. While
the current preference of sockets over cores in smp parsing results
in a virtual cpu topology with low cores-per-sockets counts and a
large number of sockets, which is just contrary to the real world.
Given that it is better to make the virtual cpu topology be more
reflective of the real world and also for the sake of compatibility,
we start to prefer cores over sockets over threads in smp parsing
since machine type 6.2 for different arches.
In this patch, a boolean "smp_prefer_sockets" is added, and we only
enable the old preference on older machines and enable the new one
since type 6.2 for all arches by using the machine compat mechanism.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-10-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We have two requirements for a valid SMP configuration:
the product of "sockets * cores * threads" must represent all the
possible cpus, i.e., max_cpus, and then must include the initially
present cpus, i.e., smp_cpus.
So we only need to ensure 1) "sockets * cores * threads == maxcpus"
at first and then ensure 2) "maxcpus >= cpus". With a reasonable
order of the sanity check, we can simplify the error reporting code.
When reporting an error message we also report the exact value of
each topology member to make users easily see what's going on.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210929025816.21076-7-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently we directly calculate the omitted cpus based on the given
incomplete collection of parameters. This makes some cmdlines like:
-smp maxcpus=16
-smp sockets=2,maxcpus=16
-smp sockets=2,dies=2,maxcpus=16
-smp sockets=2,cores=4,maxcpus=16
not work. We should probably set the value of cpus to match maxcpus
if it's omitted, which will make above configs start to work.
So the calculation logic of cpus/maxcpus after this patch will be:
When both maxcpus and cpus are omitted, maxcpus will be calculated
from the given parameters and cpus will be set equal to maxcpus.
When only one of maxcpus and cpus is given then the omitted one
will be set to its counterpart's value. Both maxcpus and cpus may
be specified, but maxcpus must be equal to or greater than cpus.
Note: change in this patch won't affect any existing working cmdlines
but allows more incomplete configs to be valid.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-6-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We are currently using maxcpus to calculate the omitted sockets
but using cpus to calculate the omitted cores/threads. This makes
cmdlines like:
-smp cpus=8,maxcpus=16
-smp cpus=8,cores=4,maxcpus=16
-smp cpus=8,threads=2,maxcpus=16
work fine but the ones like:
-smp cpus=8,sockets=2,maxcpus=16
-smp cpus=8,sockets=2,cores=4,maxcpus=16
-smp cpus=8,sockets=2,threads=2,maxcpus=16
break the sanity check.
Since we require for a valid config that the product of "sockets * cores
* threads" should equal to the maxcpus, we should uniformly use maxcpus
to calculate their omitted values.
Also the if-branch of "cpus == 0 || sockets == 0" was split into two
branches of "cpus == 0" and "sockets == 0" so that we can clearly read
that we are parsing the configuration with a preference on cpus over
sockets over cores over threads.
Note: change in this patch won't affect any existing working cmdlines
but improves consistency and allows more incomplete configs to be valid.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-5-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To pave the way for the functional improvement in later patches,
make some refactor/cleanup for the smp parsers, including using
local maxcpus instead of ms->smp.max_cpus in the calculation,
defaulting dies to 0 initially like other members, cleanup the
sanity check for dies.
We actually also fix a hidden defect by avoiding directly using
the provided *zero value* in the calculation, which could cause
a segment fault (e.g. using dies=0 in the calculation).
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-4-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the SMP configuration, we should either provide a topology
parameter with a reasonable value (greater than zero) or just
omit it and QEMU will compute the missing value.
The users shouldn't provide a configuration with any parameter
of it specified as zero (e.g. -smp 8,sockets=0) which could
possibly cause unexpected results in the -smp parsing. So we
deprecate this kind of configurations since 6.2 by adding the
explicit sanity check.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-3-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here's the next batch of ppc related patches for qemu-6.2. Highlights
are:
* Fixes for several TCG math instructions from the El Dorado Institute
* A number of improvements to the powernv machine type
* Support for a new DEVICE_UNPLUG_GUEST_ERROR QAPI event from Daniel
Barboza
* Support for the new FORM2 PAPR NUMA representation. This allows
more specific NUMA distances, as well as asymmetric configurations
* Fix for 64-bit decrementer (used on MicroWatt CPUs)
* Assorted fixes and cleanups
* A number of updates to MAINTAINERS
Note that the DEVICE_UNPLUG_GUEST_ERROR stuff includes changes to
files outside my normal area, but has suitable Acks.
The MAINTAINERS updates are mostly about marking minor platforms
unmaintained / orphaned, and moving some pieces away from myself and
Greg. As we move onto other projects, we're going to need to drop
more of the ppc maintainership, though we're hoping we can avoid too
abrupt a change.
-----BEGIN PGP SIGNATURE-----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=shYQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.2-20210930' into staging
ppc patch queue for 2021-09-30
Here's the next batch of ppc related patches for qemu-6.2. Highlights
are:
* Fixes for several TCG math instructions from the El Dorado Institute
* A number of improvements to the powernv machine type
* Support for a new DEVICE_UNPLUG_GUEST_ERROR QAPI event from Daniel
Barboza
* Support for the new FORM2 PAPR NUMA representation. This allows
more specific NUMA distances, as well as asymmetric configurations
* Fix for 64-bit decrementer (used on MicroWatt CPUs)
* Assorted fixes and cleanups
* A number of updates to MAINTAINERS
Note that the DEVICE_UNPLUG_GUEST_ERROR stuff includes changes to
files outside my normal area, but has suitable Acks.
The MAINTAINERS updates are mostly about marking minor platforms
unmaintained / orphaned, and moving some pieces away from myself and
Greg. As we move onto other projects, we're going to need to drop
more of the ppc maintainership, though we're hoping we can avoid too
abrupt a change.
# gpg: Signature made Thu 30 Sep 2021 06:42:41 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.2-20210930: (44 commits)
MAINTAINERS: Demote sPAPR from "Supported" to "Maintained"
MAINTAINERS: Add information for OpenPIC
MAINTAINERS: Remove David & Greg as reviewers/co-maintainers of powernv
MAINTAINERS: Orphan obscure ppc platforms
MAINTAINERS: Remove David & Greg as reviewers for a number of boards
MAINTAINERS: Remove machine specific files from ppc TCG CPUs entry
spapr/xive: Fix kvm_xive_source_reset trace event
spapr_numa.c: fixes in spapr_numa_FORM2_write_rtas_tables()
hw/intc: openpic: Clean up the styles
hw/intc: openpic: Drop Raven related codes
hw/intc: openpic: Correct the reset value of IPIDR for FSL chipset
target/ppc: Fix 64-bit decrementer
target/ppc: Convert debug to trace events (decrementer and IRQ)
spapr_numa.c: handle auto NUMA node with no distance info
spapr_numa.c: FORM2 NUMA affinity support
spapr: move FORM1 verifications to post CAS
spapr_numa.c: rename numa_assoc_array to FORM1_assoc_array
spapr_numa.c: parametrize FORM1 macros
spapr_numa.c: scrap 'legacy_numa' concept
spapr_numa.c: split FORM1 code into helpers
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a name field for all the memory listeners. It can be used to identify
which memory listener is which.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210817013553.30584-2-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Libvirt can use query-sgx-capabilities to get the host
sgx capabilities to decide how to allocate SGX EPC size to VM.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The QMP and HMP interfaces can be used by monitor or QMP tools to retrieve
the SGX information from VM side when SGX is enabled on Intel platform.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since there is no fill_device_info() callback support, and when we
execute "info memory-devices" command in the monitor, the segfault
will be found.
This patch will add this callback support and "info memory-devices"
will show sgx epc memory exposed to guest. The result as below:
qemu) info memory-devices
Memory device [sgx-epc]: ""
memaddr: 0x180000000
size: 29360128
memdev: /objects/mem1
Memory device [sgx-epc]: ""
memaddr: 0x181c00000
size: 10485760
memdev: /objects/mem2
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-33-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable SGX EPC virtualization, which is currently only support by KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-22-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enable SGX EPC virtualization, which is currently only support by KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-21-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ACPI Device entry for SGX EPC is essentially a hack whose primary
purpose is to provide software with a way to autoprobe SGX support,
e.g. to allow software to implement SGX support as a driver. Details
on the individual EPC sections are not enumerated through ACPI tables,
i.e. software must enumerate the EPC sections via CPUID. Furthermore,
software expects to see only a single EPC Device in the ACPI tables
regardless of the number of EPC sections in the system.
However, several versions of Windows do rely on the ACPI tables to
enumerate the address and size of the EPC. So, regardless of the number
of EPC sections exposed to the guest, create exactly *one* EPC device
with a _CRS entry that spans the entirety of all EPC sections (which are
guaranteed to be contiguous in Qemu).
Note, NUMA support for EPC memory is intentionally not considered as
enumerating EPC NUMA information is not yet defined for bare metal.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-20-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Note that SGX EPC is currently guaranteed to reside in a single
contiguous chunk of memory regardless of the number of EPC sections.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-19-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add helpers to detect if SGX EPC exists above 4g, and if so, where SGX
EPC above 4g ends. Use the helpers to adjust the device memory range
if SGX EPC exists above 4g.
For multiple virtual EPC sections, we just put them together physically
contiguous for the simplicity because we don't support EPC NUMA affinity
now. Once the SGX EPC NUMA support in the kernel SGX driver, we will
support this in the future.
Note that SGX EPC is currently hardcoded to reside above 4g.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Request SGX an SGX Launch Control to be enabled in FEATURE_CONTROL
when the features are exposed to the guest. Our design is the SGX
Launch Control bit will be unconditionally set in FEATURE_CONTROL,
which is unlike host bios.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-17-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose SGX to the guest if and only if KVM is enabled and supports
virtualization of SGX. While the majority of ENCLS can be emulated to
some degree, because SGX uses a hardware-based root of trust, the
attestation aspects of SGX cannot be emulated in software, i.e.
ultimately emulation will fail as software cannot generate a valid
quote/report. The complexity of partially emulating SGX in Qemu far
outweighs the value added, e.g. an SGX specific simulator for userspace
applications can emulate SGX for development and testing purposes.
Note, access to the PROVISIONKEY is not yet advertised to the guest as
KVM blocks access to the PROVISIONKEY by default and requires userspace
to provide additional credentials (via ioctl()) to expose PROVISIONKEY.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because SGX EPC is enumerated through CPUID, EPC "devices" need to be
realized prior to realizing the vCPUs themselves, i.e. long before
generic devices are parsed and realized. From a virtualization
perspective, the CPUID aspect also means that EPC sections cannot be
hotplugged without paravirtualizing the guest kernel (hardware does
not support hotplugging as EPC sections must be locked down during
pre-boot to provide EPC's security properties).
So even though EPC sections could be realized through the generic
-devices command, they need to be created much earlier for them to
actually be usable by the guest. Place all EPC sections in a
contiguous block, somewhat arbitrarily starting after RAM above 4g.
Ensuring EPC is in a contiguous region simplifies calculations, e.g.
device memory base, PCI hole, etc..., allows dynamic calculation of the
total EPC size, e.g. exposing EPC to guests does not require -maxmem,
and last but not least allows all of EPC to be enumerated in a single
ACPI entry, which is expected by some kernels, e.g. Windows 7 and 8.
The new compound properties command for sgx like below:
......
-object memory-backend-epc,id=mem1,size=28M,prealloc=on \
-object memory-backend-epc,id=mem2,size=10M \
-M sgx-epc.0.memdev=mem1,sgx-epc.1.memdev=mem2
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-6-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SGX EPC is enumerated through CPUID, i.e. EPC "devices" need to be
realized prior to realizing the vCPUs themselves, which occurs long
before generic devices are parsed and realized. Because of this,
do not allow 'sgx-epc' devices to be instantiated after vCPUS have
been created.
The 'sgx-epc' device is essentially a placholder at this time, it will
be fully implemented in a future patch along with a dedicated command
to create 'sgx-epc' devices.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add new CONFIG_SGX for sgx support in the Qemu, and the Kconfig
default enable sgx in the i386 platform.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-32-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new RAMBlock flag to denote "protected" memory, i.e. memory that
looks and acts like RAM but is inaccessible via normal mechanisms,
including DMA. Use the flag to skip protected memory regions when
mapping RAM for DMA in VFIO.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Linux spi-imx driver does not work on QEMU. The reason is that the
state of m25p80 loops in STATE_READING_DATA state after receiving
RDSR command, the new command is ignored. Before sending a new command,
CS line should be pulled high to make the state of m25p80 back to IDLE.
Currently the SPI flash CS line is connected to the SPI controller, but
on the real board, it's connected to GPIO3_19. This matches the ecspi1
device node in the board dts.
ecspi1 node in imx6qdl-sabrelite.dtsi:
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash: m25p80@0 {
compatible = "sst,sst25vf016b", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
Should connect the SSI_GPIO_CS to GPIO3_19 when adding a spi-nor to
spi1 on sabrelite machine.
Verified this patch on Linux v5.14.
Logs:
# echo "01234567899876543210" > test
# mtd_debug erase /dev/mtd0 0x0 0x1000
Erased 4096 bytes from address 0x00000000 in flash
# mtd_debug write /dev/mtdblock0 0x0 20 test
Copied 20 bytes from test to address 0x00000000 in flash
# mtd_debug read /dev/mtdblock0 0x0 20 test_out
Copied 20 bytes from address 0x00000000 in flash to test_out
# cat test_out
01234567899876543210#
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210927142825.491-1-xchengl.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function ide_bus_new() does an in-place initialization. Rename
it to ide_bus_init() to follow our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com> (Feel free to merge.)
Message-id: 20210923121153.23754-7-peter.maydell@linaro.org
Rename the "allocate and return" qbus creation function to
qbus_new(), to bring it into line with our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210923121153.23754-6-peter.maydell@linaro.org
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
Rename the pci_root_bus_new_inplace() function to
pci_root_bus_init(); this brings the bus type in to line with a
"_init for in-place init, _new for allocate-and-return" convention.
To do this we need to rename the implementation-internal function
that was using the pci_root_bus_init() name to
pci_root_bus_internal_init().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-4-peter.maydell@linaro.org
Rename ipack_bus_new_inplace() to ipack_bus_init(), to bring it in to
line with a "_init for in-place init, _new for allocate-and-return"
convention. Drop the 'name' argument, because the only caller does
not pass in a name. If a future caller does need to specify the bus
name, we should create an ipack_bus_init_named() function at that
point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-3-peter.maydell@linaro.org
The function scsi_bus_new() creates a new SCSI bus; callers can
either pass in a name argument to specify the name of the new bus, or
they can pass in NULL to allow the bus to be given an automatically
generated unique name. Almost all callers want to use the
autogenerated name; the only exception is the virtio-scsi device.
Taking a name argument that should almost always be NULL is an
easy-to-misuse API design -- it encourages callers to think perhaps
they should pass in some standard name like "scsi" or "scsi-bus". We
don't do this anywhere for SCSI, but we do (incorrectly) do it for
other bus types such as i2c.
The function name also implies that it will return a newly allocated
object, when it in fact does in-place allocation. We more commonly
name such functions foo_init(), with foo_new() being the
allocate-and-return variant.
Replace all the scsi_bus_new() callsites with either:
* scsi_bus_init() for the usual case where the caller wants
an autogenerated bus name
* scsi_bus_init_named() for the rare case where the caller
needs to specify the bus name
and document that for the _named() version it's then the caller's
responsibility to think about uniqueness of bus names.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210923121153.23754-2-peter.maydell@linaro.org
Connect the support for ZynqMP eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=3,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 768 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-9-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Xilinx ZynqMP Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=2,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-8-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=1,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 3072 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-7-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=0,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-6-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device is present in Versal and ZynqMP product
families to store a 256-bit encryption key.
Co-authored-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Co-authored-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-5-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements the Xilinx ZynqMP eFuse, an one-time
field-programmable non-volatile storage device. There is
only one such device in the Xilinx ZynqMP product family.
Co-authored-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Co-authored-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-4-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements the Xilinx Versal eFuse, an one-time
field-programmable non-volatile storage device. There is
only one such device in the Xilinx Versal product family.
This device has two separate mmio interfaces, a controller
and a flatten readback.
The controller provides interfaces for field-programming,
configuration, control, and status.
The flatten readback is a cache to provide a byte-accessible
read-only interface to efficiently read efuse array.
Co-authored-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Co-authored-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-3-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces the QOM for Xilinx eFuse, an one-time
field-programmable storage bit array.
The actual mmio interface to the array varies by device
families and will be provided in different change-sets.
Co-authored-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Co-authored-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-2-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 SoC uses Cortex-A7 cores which support virtualization.
However, today we are configuring QEMU to use HVC as PSCI conduit.
That means HVC calls get trapped into QEMU instead of the guest's own
emulated CPU and thus break the guest's ability to execute virtualization.
Fix this by moving to SMC as conduit, freeing up HYP completely to the VM.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20210920203931.66527-1-agraf@csgraf.de
Fixes: 740dafc0ba ("hw/arm: add Allwinner H3 System-on-Chip")
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The trace event was placed in the wrong routine. Move it under
kvmppc_xive_source_reset_one().
Fixes: 4e960974d4 ("xive: Add trace events")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210922070205.1235943-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch has a handful of modifications for the recent added
FORM2 support:
- to not allocate more than the necessary size in 'distance_table'.
At this moment the array is oversized due to allocating uint32_t for
all elements, when most of them fits in an uint8_t. Fix it by
changing the array to uint8_t and allocating the exact size;
- use stl_be_p() to store the uint32_t at the start of 'distance_table';
- use sizeof(uint32_t) to skip the uint32_t length when populating the
distances;
- use the NUMA_DISTANCE_MIN macro from sysemu/numa.h to avoid hardcoding
the local distance value.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210922122852.130054-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Correct the multi-line comment format. No functional changes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210918032653.646370-3-bin.meng@windriver.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is no machine that uses Motorola MCP750 (aka Raven) model.
Drop the related codes.
While we are here, drop the mentioning of Intel GW80314 I/O
companion chip in the comments as it has been obsolete for years,
and correct a typo too.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210918032653.646370-2-bin.meng@windriver.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The reset value of IPIDR should be zero for Freescale chipset, per
the following 2 manuals I checked:
- P2020RM (https://www.nxp.com/webapp/Download?colCode=P2020RM)
- P4080RM (https://www.nxp.com/webapp/Download?colCode=P4080RM)
Currently it is set to 1, which leaves the IPI enabled on core 0
after power-on reset. Such may cause unexpected interrupt to be
delivered to core 0 if the IPI is triggered from core 0 to other
cores later.
Fixes: ffd5e9fe02 ("openpic: Reset IRQ source private members")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/584
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210918032653.646370-1-bin.meng@windriver.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current way the mask is built can overflow with a 64-bit decrementer.
Use sextract64() to extract the signed values and remove the logic to
handle negative values which has become useless.
Cc: Luis Fernando Fujita Pires <luis.pires@eldorado.org.br>
Fixes: a8dafa5251 ("target/ppc: Implement large decrementer support for TCG")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-5-clg@kaod.org>
Reviewed-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
numa_complete_configuration() in hw/core/numa.c always adds a NUMA node
for the pSeries machine if none was specified, but without node distance
information for the single node created.
NUMA FORM1 affinity code didn't rely on numa_state information to do its
job, but FORM2 does. As is now, this is the result of a pSeries guest
with NUMA FORM2 affinity when no NUMA nodes is specified:
$ numactl -H
available: 1 nodes (0)
node 0 cpus: 0
node 0 size: 16222 MB
node 0 free: 15681 MB
No distance information available.
This can be amended in spapr_numa_FORM2_write_rtas_tables(). We're
enforcing that the local distance (the distance to the node to itself) is
always 10. This allows for the proper creation of the NUMA distance tables,
fixing the output of 'numactl -H' in the guest:
$ numactl -H
available: 1 nodes (0)
node 0 cpus: 0
node 0 size: 16222 MB
node 0 free: 15685 MB
node distances:
node 0
0: 10
CC: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-8-danielhb413@gmail.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The main feature of FORM2 affinity support is the separation of NUMA
distances from ibm,associativity information. This allows for a more
flexible and straightforward NUMA distance assignment without relying on
complex associations between several levels of NUMA via
ibm,associativity matches. Another feature is its extensibility. This base
support contains the facilities for NUMA distance assignment, but in the
future more facilities will be added for latency, performance, bandwidth
and so on.
This patch implements the base FORM2 affinity support as follows:
- the use of FORM2 associativity is indicated by using bit 2 of byte 5
of ibm,architecture-vec-5. A FORM2 aware guest can choose to use FORM1
or FORM2 affinity. Setting both forms will default to FORM2. We're not
advertising FORM2 for pseries-6.1 and older machine versions to prevent
guest visible changes in those;
- ibm,associativity-reference-points has a new semantic. Instead of
being used to calculate distances via NUMA levels, it's now used to
indicate the primary domain index in the ibm,associativity domain of
each resource. In our case it's set to {0x4}, matching the position
where we already place logical_domain_id;
- two new RTAS DT artifacts are introduced: ibm,numa-lookup-index-table
and ibm,numa-distance-table. The index table is used to list all the
NUMA logical domains of the platform, in ascending order, and allows for
spartial NUMA configurations (although QEMU ATM doesn't support that).
ibm,numa-distance-table is an array that contains all the distances from
the first NUMA node to all other nodes, then the second NUMA node
distances to all other nodes and so on;
- get_max_dist_ref_points(), get_numa_assoc_size() and get_associativity()
now checks for OV5_FORM2_AFFINITY and returns FORM2 values if the guest
selected FORM2 affinity during CAS.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-7-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
FORM2 NUMA affinity is prepared to deal with empty (memory/cpu less)
NUMA nodes. This is used by the DAX KMEM driver to locate a PAPR SCM
device that has a different latency than the original NUMA node from the
regular memory. FORM2 is also able to deal with asymmetric NUMA
distances gracefully, something that our FORM1 implementation doesn't
do.
Move these FORM1 verifications to a new function and wait until after
CAS, when we're sure that we're sticking with FORM1, to enforce them.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-6-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introducing a new NUMA affinity, FORM2, requires a new mechanism to
switch between affinity modes after CAS. Also, we want FORM2 data
structures and functions to be completely separated from the existing
FORM1 code, allowing us to avoid adding new code that inherits the
existing complexity of FORM1.
The idea of switching values used by the write_dt() functions in
spapr_numa.c was already introduced in the previous patch, and
the same approach will be used when dealing with the FORM1 and FORM2
arrays.
We can accomplish that by that by renaming the existing numa_assoc_array
to FORM1_assoc_array, which now is used exclusively to handle FORM1 affinity
data. A new helper get_associativity() is then introduced to be used by the
write_dt() functions to retrieve the current ibm,associativity array of
a given node, after considering affinity selection that might have been
done during CAS. All code that was using numa_assoc_array now needs to
retrieve the array by calling this function.
This will allow for an easier plug of FORM2 data later on.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-5-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The next preliminary step to introduce NUMA FORM2 affinity is to make
the existing code independent of FORM1 macros and values, i.e.
MAX_DISTANCE_REF_POINTS, NUMA_ASSOC_SIZE and VCPU_ASSOC_SIZE. This patch
accomplishes that by doing the following:
- move the NUMA related macros from spapr.h to spapr_numa.c where they
are used. spapr.h gets instead a 'NUMA_NODES_MAX_NUM' macro that is used
to refer to the maximum number of NUMA nodes, including GPU nodes, that
the machine can support;
- MAX_DISTANCE_REF_POINTS and NUMA_ASSOC_SIZE are renamed to
FORM1_DIST_REF_POINTS and FORM1_NUMA_ASSOC_SIZE. These FORM1 specific
macros are used in FORM1 init functions;
- code that uses MAX_DISTANCE_REF_POINTS now retrieves the
max_dist_ref_points value using get_max_dist_ref_points().
NUMA_ASSOC_SIZE is replaced by get_numa_assoc_size() and VCPU_ASSOC_SIZE
is replaced by get_vcpu_assoc_size(). These functions are used by the
generic device tree functions and h_home_node_associativity() and will
allow them to switch between FORM1 and FORM2 without changing their core
logic.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When first introduced, 'legacy_numa' was a way to refer to guests that
either wouldn't be affected by associativity domain calculations, namely
the ones with only 1 NUMA node, and pre 5.2 guests that shouldn't be
affected by it because it would be an userspace change. Calling these
cases 'legacy_numa' was a convenient way to label these cases.
We're about to introduce a new NUMA affinity, FORM2, and this concept
of 'legacy_numa' is now a bit misleading because, although it is called
'legacy' it is in fact a FORM1 exclusive contraint.
This patch removes spapr_machine_using_legacy_numa() and open code the
conditions in each caller. While we're at it, move the chunk inside
spapr_numa_FORM1_affinity_init() that sets all numa_assoc_array domains
with 'node_id' to spapr_numa_define_FORM1_domains(). This chunk was
being executed if !pre_5_2_numa_associativity and num_nodes => 1, the
same conditions in which spapr_numa_define_FORM1_domains() is called
shortly after.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The upcoming FORM2 NUMA affinity will support asymmetric NUMA topologies
and doesn't need be concerned with all the legacy support for older
pseries FORM1 guests.
We're also not going to calculate associativity domains based on numa
distance (via spapr_numa_define_associativity_domains) since the
distances will be written directly into new DT properties.
Let's split FORM1 code into its own functions to allow for easier
insertion of FORM2 logic later on.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210920174947.556324-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If an unknown pin of the IRQ controller is raised, something is very
wrong in the QEMU model. It is better to abort.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210920061203.989563-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MEM_UNPLUG_ERROR is deprecated since the introduction of
DEVICE_UNPLUG_GUEST_ERROR. Keep emitting both while the deprecation of
MEM_UNPLUG_ERROR is pending.
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-8-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Linux Kernel 5.12 is now unisolating CPU DRCs in the device_removal
error path, signalling that the hotunplug process wasn't successful.
This allow us to send a DEVICE_UNPLUG_GUEST_ERROR in drc_unisolate_logical()
to signal this error to the management layer.
We also have another error path in spapr_memory_unplug_rollback() for
configured LMB DRCs. Kernels older than 5.13 will not unisolate the LMBs
in the hotunplug error path, but it will reconfigure them. Let's send
the DEVICE_UNPLUG_GUEST_ERROR event in that code path as well to cover the
case of older kernels.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-7-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The error_report() call in drc_unisolate_logical() is not considering
that drc->dev->id can be NULL, and the underlying functions error_report()
calls to do its job (vprintf(), g_strdup_printf() ...) has undefined
behavior when trying to handle "%s" with NULL arguments.
Besides, there is no utility into reporting that an unknown device was
rejected by the guest.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As done in hw/acpi/memory_hotplug.c, pass an empty string if dev->id
is NULL to qapi_event_send_mem_unplug_error() to avoid relying on
a behavior that can be changed in the future.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qapi_event_send_mem_unplug_error() deals with @device being NULL by
replacing it with an empty string ("") when emitting the event. Aside
from the fact that this behavior (qapi visitor mapping NULL pointer to
"") can be patched/changed someday, there's also the lack of utility
that the event brings to listeners, e.g. "a memory unplug error happened
somewhere".
In theory we should just avoit emitting this event at all if dev->id is
NULL, but this would be an incompatible change to existing guests.
Instead, let's make the forementioned behavior explicit: if dev->id is
NULL, pass an empty string to qapi_event_send_mem_unplug_error().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210907004755.424931-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210902130928.528803-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This to avoid possible conflicts with the "id" property of QOM objects.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On P10, the chip id is calculated from the "Primary topology table
index". See skiboot commits for more information [1].
This information is extracted from the hdata on real systems which
QEMU needs to emulate. Add this property for all machines even if it
is only used on POWER10.
[1] https://github.com/open-power/skiboot/commit/2ce3f083f399https://github.com/open-power/skiboot/commit/a2d4d7f9e14a
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901094153.227671-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Drop abs64() and use uabs64() from host-utils, which avoids
an undefined behavior when taking abs of the most negative value.
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20210910112624.72748-5-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Slot 0x9 is reserved for use by the in-built framebuffer whilst only slots
0xc, 0xd and 0xe physically exist on the Quadra 800.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Nubus IRQs are routed to the CPU through the VIA2 device so wire up the IRQs
using gpios accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Each Nubus slot has an IRQ line that can be used to request service from the
CPU. Connect the IRQs to the Nubus bridge so that they can be wired up using qdev
gpios accordingly, and introduce a new nubus_set_irq() function that can be used
by Nubus devices to control the slot IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210924073808.1041-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is to allow Macintosh machines to further specify which slots are available
since the number of addressable slots may not match the number of physical slots
present in the machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210924073808.1041-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since nubus-bridge is a container for NubusBus then it should be embedded
directly within the bridge device using qbus_create_inplace().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Now that Nubus has its own address space rather than mapping directly into the
system bus, move the Nubus reference from MacNubusBridge to NubusBridge.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
