Commit 36388314fe moved most of the
interrupt logic to cpu-exec.c. Remove the remaining useless code
and fix software interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Edgar E. Iglesias <edgar@axis.com>
Tested-by: Edgar E. Iglesias <edgar@axis.com>
When hw interrupt pending bits in CP0_Cause are set, the CPU should
see the hw interrupt line as active. The CPU may or may not take the
interrupt based on internal state (global irq mask etc) but the glue
logic shouldn't care.
This fixes MIPS external hw interrupts in combination with -icount.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
The request completion callback of the LSI controller may start the next
request that can use the same tag as the completed one. As the latter is
still enqueued at that point, scsi_send_command will complain about the
tag reuse and cancel the completed request. That will cause a double
free later on when the completion path cleans up as well.
Fix this by dequeuing the request before invoking the callback.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change fixes initialization of e1000's microwire EEPROM internal
state values so that qemu's e1000 emulation works on NetBSD,
which doesn't use Intel's em driver but has its own wm driver
for the Intel i8254x Gigabit Ethernet.
Previously set_eecd() function in e1000.c clears EEPROM internal state
values on SK rising edge during CS==L, but according to FM93C06 EEPROM
(which is MicroWire compatible) data sheet, EEPROM internal status
should be cleared on CS rise edge regardless of SK input:
"... a rising edge on this (CS) signal is required to reset the internal
state-machine to accept a new cycle .."
and nothing should be changed during CS (chip select) is inactive.
Intel's em driver seems to explicitly raise SK output after CS is negated
in em_standby_eeprom() so many other OSes that use Intel's driver
don't have this problem even on the previous e1000.c implementation,
but I can't find any articles that say the MICROWIRE or EEPROM spec
requires such sequence, and actually hardware works fine without it
(i.e. real i82540EM has been working on NetBSD).
This fix also changes initialization to clear each state value in
struct eecd_state individually rather than using memset() against
the whole structre. The old_eecd member stores the last SK and CS
signal levels and it should be preserved even after reset of internal
EEPROM state to detect next signal edges for proper EEPROM emulation.
Signed-off-by: Izumi Tsutsui <tsutsui@ceres.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Starting with qemu -M pc-0.12 -device virtio-serial
results in
-device virtio-serial: Property 'virtio-serial-pci.max_nr_ports' not found
The property name 'max_ports' is incorrectly named 'max_nr_ports'. Fix
that.
Also fix the ppc440 machine type bamboo-0.12 which has this typo.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use empty_slot to reserve addresses for several unimplemented devices so they won't fault.
- BPP (parallel port), DBRI (audio), SX (pixel processor), and vsimms (framebuffer)
OBP for SS-20 either assumes these devices exist or probes without expecting faults.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We need to know ring layout to allocate log buffer.
So init rings first.
Also fixes a theoretical memory-leak-on-error.
https://bugzilla.redhat.com/show_bug.cgi?id=615228
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
We do range check for size, and get size as buffer,
but copy size + 4 bytes (4 is for FCS).
Let's copy size bytes but put size + 4 in length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Disks without media make no sense. For SCSI, a Linux guest kernel
complains during boot. I didn't try other combinations.
scsi-generic doesn't need the additional check, because it already
requires bdrv_is_sg(), which fails without media.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the check from virtio_blk_init_pci(), where it protects only
virtio-blk-pci, to virtio_blk_init(). Without that, virtio-blk-s390
initializes without a drive. I figure that can lead to null pointer
dereferences.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It can't actually fail now, but the next commit will change that.
s390_virtio_blk_init() already checks for failure, but
virtio_blk_init_pci() doesn't. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In addition to the previous fix for calling do_flush_queued_data() only
when the virtqueue is ready, ensure do_flush_queued_data() gets a vq
that's suitably initialised.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a virtio-serial port is removed before the guest comes up and
initialises the virtqueues, qemu exits with the message
Guest moved used index from 0 to 61440
This happens because we try to clear any pending buffers from the
virtqueue.
Ensure the virtqueue is initialised before calling any virtqueue
operations.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While running in debug mode if 9P server is unable to open the log file
it results in a SEGV deep down in glibc:
Program received signal SIGSEGV, Segmentation fault.
0x008fca8c in fwrite () from /lib/libc.so.6
(gdb) bt
#0 0x008fca8c in fwrite () from /lib/libc.so.6
#1 0x081eb87e in pprint_pdu (pdu=0x89a52e1c)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p-debug.c:380
#2 0x0806dad8 in submit_pdu (s=0x897dc008, pdu=0x89a52e1c)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p.c:3092
#3 0x0806dc63 in handle_9p_output (vdev=0x897dc008, vq=0x86d8218)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p.c:3122
#4 0x081ac728 in virtio_queue_notify (vdev=0x897dc008, n=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio.c:563
#5 0x08063876 in virtio_ioport_write (opaque=0x86d7b98, addr=16, val=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-pci.c:222
#6 0x08063e26 in virtio_pci_config_writew (opaque=0x86d7b98, addr=16, val=0)
at /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-pci.c:357
#7 0x080c881a in ioport_write (index=1, address=49296, data=0) at ioport.c:80
#8 0x080c8d4c in cpu_outw (addr=49296, val=0) at ioport.c:204
#9 0x08073010 in kvm_handle_io (port=49296, data=0xab393000, direction=1, size=2, count=1)
at /data/sripathi/code/qemu/new/qemu-next-upstream/kvm-all.c:735
...
...
This is ugly and misleading. The following patch adds a BUG_ON to catch this
error. With this patch we get an abort message like the following, which makes
it easier to analyze:
f12-kvm login: qemu: /data/sripathi/code/qemu/new/qemu-next-upstream/hw/virtio-9p-debug.c:353: pprint_pdu: Assertion `!(!llogfile)' failed.
Signed-off-by: Sripathi Kodi <sripathik@in.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
No need to call cpu_register_physical_memory() for a zero sized area.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The file, vt82c686.c, was added after the change set of
b80d4a9887 and
fecb93c45c
are created, but before the patch series was commit.
So similar fix is needed to vt82c686.c.
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We were requesting too much when checking buffer
length: size already includes host header length.
Further, we should not exit if we get a packet that
is too long, since this might not be under control
of the guest. Just drop the packet.
Red Hat bz 591494
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
make pci hotplug callback return value to caller.
And when returning error, allocated resources are freed.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make init value for this register match the spec.
BAR address is 0 at init, so enabling it
only works by chance.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pcnet enables memory/io on init, which
does not make sense as BAR values are wrong.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Clear interrupt disable bit on reset, according to PCI spec.
Fix pci_device_reset() with 64bit BAR.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Intel Macs have a chip called the "AppleSMC" which they use to control
certain Apple specific parts of the hardware, like the keyboard background
light.
That chip is also used to store a key that Mac OS X uses to decrypt binaries.
This patch adds emulation for that chip, so we're getting one step further
to having Mac OS X run natively on Qemu.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Set PCI multi-function bit according to multifunction property.
PCI address, devfn ,is exported to users as addr property,
so users can populate pci function(PCIDevice in qemu)
at arbitrary devfn.
It means each function(PCIDevice) don't know whether pci device
(PCIDevice[8]) is multi function or not.
So this patch allows user to set multifunction bit via property
and checks whether multifunction bit is set correctly.
Cc: Juan Quintela <quintela@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
make pci bridge aware of pci multi function property and let pci generic
code to set the bit.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
use pci_create_simple_multifunction() for normal device which sets
multifunction bit.
At the moment, only pc_piix.c and mips_malta.c uses multifunction
devices with piix3/4 pci-isa bridge.
And other boards don't populate those devices.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
introduce multifunction property.
Also introduce new convenient device creation function which
will be used later.
For bisectability this patch doesn't do anything, but sets the property
resulting in no functional changes.
Actual changes will be introduced by later patch.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
replace PCIDeviceInfo::header_type with is_bridge
as suggested by Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Auto-assigned-address pci function (passing devfn = -1) is always
single function.
This patch adds assert() to guarantee that auto-assigned-address function
is always single function device at function = 0.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use PCI_DEVFN() and PCI_FUNC_MAX where appropriate.
This patch make it clear that func = 0.
test:
The following object files with/without this patch are stripped and compared.
They remains same.
arm-softmmu/versatile_pci.o
libhw32/ppce500_pci.o
libhw32/unin_pci.o
libhw64/ppce500_pci.o
libhw64/unin_pci.o
mips-softmmu/gt64xxx.o
mips64-softmmu/gt64xxx.o
mips64el-softmmu/gt64xxx.o
mipsel-softmmu/gt64xxx.o
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yu Liu <yu.liu@freescale.com>
Cc: Paul Brook <paul@codesourcery.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
These will be used to generate unique id strings for ramblocks. The name
field is required, the device pointer is optional as most callers don't
have a device. When there's no device or the device isn't a child of
a bus implementing BusInfo.get_dev_path, the name should be unique for
the platform.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Stuff a pointer to the DeviceState into the VirtIONet structure so that
we can easily remove the vmstate entry later. Also, let vmstate track
the instance number (it should always be zero internally since the
device path should now be unique).
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows us to create a more meaningful savevm string.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When available, we'd like to be able to access the DeviceState
when registering a savevm. For buses with a get_dev_path()
function, this will allow us to create more unique savevm
id strings.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This works great for PCI since a <segment>:<bus>:<dev>.<fn> uniquely
describes a global address. No need to traverse up the qdev tree.
PCI segment support is a placeholder for compatibility once we
support multiple segments.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This function is meant to provide a stable device path for buses
which are able to implement it. If a bus has a globally unique
addresses scheme, one address level may be sufficient to provide
a path. Other buses may need to recursively traverse up the
qdev tree.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This will benefit us when we migrate based on ramblock name since
we won't be bouncing between separate blocks.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Convert alarm time from BCD if needed before comparing with current
time.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When the controller raises the SCSI reset line, we have to perform the
requested reset on all disks attached to the controller's bus. Moreover,
reset is edge triggered, so avoid repeating it if the line was already
high.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
drive_init() doesn't permit invalid CHS for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit option readonly for if=ide, but that's
worthless: we get it via if=none and -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It still always succeeds. The next commits will add failures.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The two aren't independent variables. Make that obvious.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use error_report(), because it points to the error location.
Reword "tried to assign twice" messages to make it clear that we're
complaining about the unit property.
Report invalid unit property instead of failing silently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit rerror for if=scsi, but that's worthless:
we get it via if=none and -device.
Moreover, scsi-generic doesn't support werror. Since drive_init()
doesn't catch that, option werror was silently ignored even with
if=scsi.
Wart: unlike drive_init(), we don't reject the default action when
it's explicitly specified. That's because we can't distinguish "no
rerror option" from "rerror=report", or "no werror" from
"rerror=enospc". Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some of the failures are internal errors, and hw_error() is okay then.
But the common way to fail is bad user input, e.g. -global
isa-fdc.driveA=foo where drive foo has an unsupported rerror value.
exit(1) instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_init() doesn't permit them for if=floppy, but that's worthless:
we get them via if=none and -global.
This can make device initialization fail. Since all callers of
fdctrl_init_isa() ignore its value, change it to die instead of
returning failure. Without this, some callers would ignore the
failure, and others would crash.
Wart: unlike drive_init(), we don't reject the default action when
it's explicitly specified. That's because we can't distinguish "no
rerror option" from "rerror=report", or "no werror" from
"rerror=enospc". Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the final missing bits for support of
passing a serial/id string to a virtio-blk guest driver.
The guest-side component already exists in the virtio
driver, and has recently been reworked by Ryan to export
a /sys interface for retrieval of the id from guest userland.
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drives defined with -drive if=ide get get created along with the IDE
controller, inside machine->init(). That's before cmos_init().
Drives defined with -device get created during generic device init.
That's after cmos_init(). Because of that, CMOS has no information on
them (type, geometry, translation). Older versions of Windows such as
XP reportedly choke on that.
Split off the part of CMOS initialization that needs to know about
-device devices, and turn it into a reset handler, so it runs after
device creation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable controls whether virtual media
change (monitor commands change, eject) is allowed. It is set when
the "type hint" is BDRV_TYPE_CDROM or BDRV_TYPE_FLOPPY.
The type hint is only set by drive_init(). It sets BDRV_TYPE_FLOPPY
for if=floppy. It sets BDRV_TYPE_CDROM for media=cdrom and if=ide,
scsi, xen, or none.
if=ide and if=scsi work, because the type hint makes it a CD-ROM.
if=xen likewise, I think.
For the same reason, if=none works when it's used by ide-drive or
scsi-disk. For other guest devices, there are problems:
* fdc: you can't change virtual media
$ qemu [...] -drive if=none,id=foo,... -global isa-fdc.driveA=foo
QEMU 0.12.50 monitor - type 'help' for more information
(qemu) eject foo
Device 'foo' is not removable
unless you add media=cdrom, but that makes it readonly.
* virtio: if you add media=cdrom, you can change virtual media. If
you eject, the guest gets I/O errors. If you change, the guest sees
the drive's contents suddenly change.
* scsi-generic: if you add media=cdrom, you can change virtual media.
I didn't test what that does to the guest or the physical device,
but it can't be pretty.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For instance, -device scsi-disk,drive=foo -device scsi-disk,drive=foo
happily creates two SCSI disks connected to the same block device.
It's all downhill from there.
Device usb-storage deliberately attaches twice to the same blockdev,
which fails with the fix in place. Detach before the second attach
there.
Also catch attempt to delete while a guest device model is attached.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We automatically delete blockdev host parts on unplug of the guest
device. Too much magic, but we can't change that now.
The delete happens early in the guest device teardown, before the
connection to the host part is severed. Thus, the guest part's
pointer to the host part dangles for a brief time. No actual harm
comes from this, but we'll catch such dangling pointers a few commits
down the road. Clean up the dangling pointers by delaying the
automatic deletion until the guest part's pointer is gone.
Device usb-storage deliberately makes two qdev properties refer to the
same drive, because it automatically creates a second device. Again,
too much magic we can't change now. Multiple references worked okay
before, but now free_drive() dies for the second one. Zap the extra
reference.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers of ide_create_drive() ignore its value. Currently
harmless, because it fails only when qdev_init() fails, which fails
only when ide_drive_initfn() fails, which never fails.
Brittle. Change it to die instead of silently ignoring failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
None of its callers checks for failure. scsi_hot_add() can crash
because of that:
(qemu) drive_add 4 if=scsi,format=host_device,file=/dev/sg1
scsi-generic: scsi generic interface too old
Segmentation fault (core dumped)
Fix all callers, not just scsi_hot_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
scanf calls must not use PRI constants, they have probably the wrong size and
corrupt memory. We could replace them by SCN ones, but strtol is simpler than
scanf here anyway. While at it, also fix the parsers to reject garbage after
the number ("4096xyz" was accepted before).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Richard Henderson <rth@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The commit 8e65b7c049 introduced
expire_time of UHCIState. But expire_time is not in vmstate, the
second uhci_frame_timer will not be fired immediately after loadvm.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For all i, ports_map[i] is used in and only in the i-th iteration.
Replace the dynamic array by a scalar variable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
lsi_bad_phase has a bug in the choice of pmjad1/pmjad2. This does
not matter with Linux guests because it uses just one routine for
both, but it breaks Windows 64-bit guests. This is the text
from the spec:
"[The PMJCTL] bit controls which decision mechanism is used
when jumping on phase mismatch. When this bit is cleared the
LSI53C895A will use Phase Mismatch Jump Address 1 (PMJAD1) when
the WSR bit is cleared and Phase Mismatch Jump Address 2 (PMJAD2)
when the WSR bit is set. When this bit is set the LSI53C895A will
use jump address one (PMJAD1) on data out (data out, command,
message out) transfers and jump address two (PMJAD2) on data in
(data in, status, message in) transfers."
Which means:
CCNTL0.PMJCTL
0 SCNTL2.WSR = 0 PMJAD1
0 SCNTL2.WSR = 1 PMJAD2
1 out PMJAD1
1 in PMJAD2
In qemu, what you get instead is:
CCNTL0.PMJCTL
0 out PMJAD1
0 in PMJAD2 <<<<<
1 out PMJAD1
1 in PMJAD1 <<<<<
Considering that qemu always has SCNTL2.WSR cleared, the two marked cases
(corresponding to phase mismatch on input) are always jumping to the
wrong PMJAD register. The patch implements the correct semantics.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MASTER_DISABLE bit (aka mask-all) masks all the interrupts.
According to Sun-4M System Architecture
"The level–15 interrupt sources [...] are maskable with the Interrupt Target
Mask Register. While these interrupts are considered ’non–maskable’ within
the SPARC IU, a mask capability is provided to allow the boot firmware
to establish a basic environment before receiving any level–15 interrupts,
which are non–maskable within SPARC. A mask–all bit is provided to allow
disabling of all external interrupts during change of the CIT."
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
System architecture dictates whether HAS_AUDIO is defined. It's then
useless to check for HAS_AUDIO in files which are only used on those
architectures which always have audio.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The comment suggests we're checking for the driver in the ready
state and bus master disabled, but the code is checking that it's
not in the ready state.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Found-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
On Host/Fileserver:
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:36 afifo
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:32 blkdev
-rw-------. 1 virfsuid virtfsgid 0 2010-05-11 09:33 chardev
On Guest/Client:
prw-r--r-- 1 guestuser guestuser 0 2010-05-11 12:36 afifo
brw-r--r-- 1 guestuser guestuser 0, 0 2010-05-11 12:32 blkdev
crw-r--r-- 1 guestuser guestuser 4, 5 2010-05-11 12:33 chardev
In the passthrough securit model, specifal files are directly created
on the fileserver. But the user credential
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Mapped mode stores extended attributes in the user space of the extended
attributes. Given that the user space extended attributes are available
to regular files only, special files are created as regular files on the
fileserver and appropriate mode bits are added to the extended attributes.
This method presents all special files and symlinks as regular files on the
fileserver while they are represented as special files on the guest mount.
Implemntation of symlink in mapped security model:
A regular file is created and the link target is written to it.
readlink() reads it back from the file.
On Guest/Client:
lrwxrwxrwx 1 root root 6 2010-05-11 12:20 asymlink -> afile
On Host/Fileserver:
-rw-------. 1 root root 6 2010-05-11 09:20 asymlink
afile
Under passthrough model, it just calls underlying symlink() readlink()
system calls are used.
Under both security models, client user credentials are changed
after the filesystem objec creation.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In the mapped security model, VirtFS server intercepts and maps
the file object create and get/set attribute requests. Files on the fileserver
will be created with VirtFS servers (QEMU) user credentials and the
client-users credentials are stored in extended attributes. On the request
to get attributes, server extracts the client-users credentials
from extended attributes and sends them to the client.
On Host/Fileserver:
-rw-------. 2 virfsuid virtfsgid 0 2010-05-11 09:19 afile
On Guest/Client:
-rw-r--r-- 2 guestuser guestuser 0 2010-05-11 12:19 afile
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
mapped model changes the owner in the extended attributes.
passthrough model does the change through lchown() as the
server don't need to follow the link and client will send the
actual filesystem object.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds required infrastructure for the new security model.
- A new configure option for attr/xattr.
- if CONFIG_VIRTFS will be defined if both CONFIG_LINUX and CONFIG_ATTR defined.
- Defines routines related to both security models.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The new option is:
-fsdev fstype,id=myid,path=/share_path/,security_model=[mapped|passthrough]
-virtfs fstype,path=/share_path/,security_model=[mapped|passthrough],mnt_tag=tag
In the case of mapped security model, files are created with QEMU user
credentials and the client-user's credentials are saved in extended attributes.
Whereas in the case of passthrough security model, files on the
filesystem are directly created with client-user's credentials.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch rearranges the fileop structures by moving the structure definitions
from virtio-9p.c to virtio-9p.h file. No functional changes.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch fluesh the debug messages to the log file at the end of each
debug message.
Changes from V1:
Used fflush instead fseek for the flush.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Although it is really rare to get in to the while loop, the list
operation in the loop is obviously wrong.
Signed-off-by: Yoshiaki Tamura <tamura.yoshiaki@lab.ntt.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add MAINTENANCE_IN and MAINTENANCE_OUT case in
scsi_req_length() for TYPE_ROM with MMC commands. It also adds the MAINTENANCE_OUT
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing write data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch updates hw/scsi-bus.c to add the PERSISTENT_RESERVE_OUT cdb
case in scsi_req_xfer_mode() to set SCSI_XFER_TO_DEV for outgoing WRITE data.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make APICState completely private to apic.c by using DeviceState
in external APIs.
Move apic_init() to pc.c.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Convert to qdev.
Use an opaque CPUState pointer because of missing VMState
implementation for CPUState.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move the actual CPUState contents handling to cpu.h and cpuid.c.
Handle CPU reset and set env->halted in pc.c.
Add a function to get the local APIC state of the current
CPU for the MMIO.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Comparing an 8 bit value with ~0 does not work as expected.
Replace ~0 by UINT8_MAX in comparison and also in assignment
(and fix coding style, too).
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: malc <av1474@comtv.ru>
Correct definitions for FD_CMD_SAVE and FD_CMD_RESTORE in hw/fdc.c
Per https://bugs.launchpad.net/qemu/+bug/424453 the correct values
for FD_CMD_SAVE is 0x2e and FD_CMD_RESTORE is 0x4e. Verified against
the Intel 82078 manual which can be found at:
http://wiki.qemu.org/Documentation/HardwareManuals page 22.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
That's where they belong semantically (block device host part), even
though the actions are actually executed by guest device code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PCI hotplug currently doesn't work after a migration because
we don't migrate the enable bits of the GPE state. Pull hotplug
structs into vmstate.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Setting the ID in pci_nic_init() is a blatant violation of the
DeviceState abstraction. Which even carries a comment advising
against this:
/* This structure should not be accessed directly. We declare it here
so that it can be embedded in individual device state structures. */
What's worse, it bypasses the code ensuring unique qdev IDs: "-device
virtio-net-pci,id=foo -net nic,id=foo -net nic,name=foo" happily
creates three qdevs with ID "foo". That's because qdev relies on
qemu_opts_create() to ensure unique IDs, but -net nic uses a different
QemuOptsList, which means id is in a different namespace. And its
name is not checked for uniqueness at all.
-net nic and pci_add are legacy. Use -device and device_add if you
want a NIC with a qdev ID.
This reverts what's still left of commit eb54b6dc "qdev: add id=
support for pci nics."
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When mistakenly configuring two devices in the same PCI slot,
QEMU gives a not entirely obvious message about a 'devfn' being
in use:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu-kvm: -device virtio-balloon-pci,bus=pci.0,addr=0x3: PCI: devfn 24 not available for virtio-balloon-pci, in use by rtl8139
The user does not configure 'devfn' numbers, they use slot+function.
Thus the error messages should be reported back to the user with that
same terminology rather than the internal QEMU terminology. This
patch makes it report:
$ qemu -device rtl8139 -device virtio-balloon-pci,bus=pci.0,addr=0x3
qemu: -device virtio-balloon-pci,bus=pci.0,addr=0x3.7: PCI: slot 3 function 0 not available for virtio-balloon-pci, in use by rtl8139
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Pass the MultiReqBuffer structure down all the way to the I/O submission
instead of takin it apart. Also mark num_writes unsigned as it can't
go negative, and take the check for any pending I/O requests into the
submission function. Last but not least rename do_multiwrite to
virtio_submit_multiwrite to fit the general naming scheme and make clear
what it does.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
There is a 1:1 relation between VirtIOBlock and BlockDriverState instances,
no need to track it because it won't change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If a USB keyboard is unplugged, the keyboard eventhandler is never
removed, and events will continue to be passed through to the device,
causing crashes or memory corruption.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently HPET ACPI table is created regardless of whether qemu actually
created hpet device. This may confuse some guests that don't check that
hpet is functional before using it. Solve this by passing info about
hpets in qemu to seabios via fw config interface. Additional benefit is
that seabios no longer uses hard coded hpet configuration. Proposed
interface supports up to 8 hpets. This is the number defined by hpet
spec.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The capability register is read-only from guest POV, so we do not need
to update it on reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change #define DEBUG to #define E1000_DEBUG in hw/e1000.c to make
it possible to build QEMU with -DDEBUG
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Remove unused DEBUG defines from hw/msix.c to avoid having anything
define the word DEBUG without any additions such as MSIX_DEBUG.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the HPET capability of routing IRQs to the front-side
bus, aka MSI support. This feature can be enabled via the qdev property
"msi" and is off by default.
Note that switching it on can cause guests (at least Linux) to use the
HPET as timer instead of the LAPIC. KVM users should recall that only
the latter is currently available as fast in-kernel model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
One HPET block supports up to 32 timers. Allow to instantiate more than
the recommended and implemented minimum of 3. The number is configured
via the qdev property "timers". It is also saved/restored so that it
need not match between migration peers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By implementing this feature we can also remove a nasty way to kill qemu
(by trying to enable level-triggered hpet interrupts).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of keeping a static reference around, pass the state to
hpet_enabled and hpet_get_ticks. All callers now have it at hand. Will
once allow to instantiate the HPET more than a single time.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We have to update the qemu timer when the per-timer enable bit is
toggled, just like for HPET_CFG_ENABLE changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register the HPET as a sysbus device and create it that way. As it can
route its IRQs to any ISA IRQ, we need to connect it to all 24 of them.
Once converted to qdev, we can move reset handler and vmstate
registration into its hands as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Properly initialize HPETTimer::tn and HPETTimer::state once during
hpet_init instead of (re-)writing them on every reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Setting the main counter while the HPET is enabled may not be a good
idea of the guest, but it is supported and should, thus, not spam the
host console with warnings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This moves the private HPET structures into the C module, simplifies
some helper functions and fixes most coding style issues (biggest chunk
was improper switch-case indention). No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
