Since commit
ba3e792669 ("icount: clean up cpu_can_io at the entry to the block")
it has been unnecessary for target code to call gen_io_end() after an IO
instruction in icount mode; it is sufficient to call gen_io_start()
before it and to force the end of the TB.
Remaining call in xtensa target translator is for the opcodes that may
change IRQ state. All of them end current TB, so gen_io_end is not
needed. Drop gen_io_end call from the xtensa target translator.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Give the previously unnamed enum a typedef name. Use it in the
prototypes of compare functions. Use it to hold the results
of the compare functions.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
After Xtensa release RE.2 simcall opcode has become nop for the
hardware instead of illegal instruction.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa architecture has features which behavior depends on hardware
version. Provide hardware version information to translators: add
XtensaConfig::hw_version and use XCHAL_HW_VERSION from configuration
overlay to initialize it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa configuration overlays for recent releases may have special
registers for which [rwx]sr opcodes are defined, but they are not listed
as SR in xtensa_sysreg_name and associated functions. As a result
generic translate_[rwx]sr* functions generate access to uninitialized
cpu_SR causing segfault at runtime.
Don't try to access cpu_SR for such registers, ignore writes and return
0 for reads.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Introduce gdb_get_zeroes() to fill a GByteArray with zeroes.
Fixes: a010bdbe71 ("extend GByteArray to read register helpers")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200414102427.7459-1-philmd@redhat.com>
[AJB: used slightly more gliby set_size approach]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20200414200631.12799-13-alex.bennee@linaro.org>
Rather than dynamically allocate, and risk failing to free
when we longjmp out of the translator, allocate the maximum
buffer size based on the maximum supported instruction length.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Dynamically allocating a new structure within the DisasContext can
potentially leak as we can longjmp out of the translation loop (see
test_phys_mem). The proper fix would be to use static allocation
within the DisasContext but as the Xtensa translator imports it's code
from elsewhere I leave that as an exercise for the maintainer.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20200403191150.863-6-alex.bennee@linaro.org>
Bug fixes:
* memory encryption: Disable mem merge
(Dr. David Alan Gilbert)
Features:
* New EPYC CPU definitions (Babu Moger)
* Denventon-v2 CPU model (Tao Xu)
* New 'note' field on versioned CPU models (Tao Xu)
Cleanups:
* x86 CPU topology cleanups (Babu Moger)
* cpu: Use DeviceClass reset instead of a special CPUClass reset
(Peter Maydell)
-----BEGIN PGP SIGNATURE-----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=9fEL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-and-machine-pull-request' into staging
x86 and machine queue for 5.0 soft freeze
Bug fixes:
* memory encryption: Disable mem merge
(Dr. David Alan Gilbert)
Features:
* New EPYC CPU definitions (Babu Moger)
* Denventon-v2 CPU model (Tao Xu)
* New 'note' field on versioned CPU models (Tao Xu)
Cleanups:
* x86 CPU topology cleanups (Babu Moger)
* cpu: Use DeviceClass reset instead of a special CPUClass reset
(Peter Maydell)
# gpg: Signature made Wed 18 Mar 2020 01:16:43 GMT
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-and-machine-pull-request:
hw/i386: Rename apicid_from_topo_ids to x86_apicid_from_topo_ids
hw/i386: Update structures to save the number of nodes per package
hw/i386: Remove unnecessary initialization in x86_cpu_new
machine: Add SMP Sockets in CpuTopology
hw/i386: Consolidate topology functions
hw/i386: Introduce X86CPUTopoInfo to contain topology info
cpu: Use DeviceClass reset instead of a special CPUClass reset
machine/memory encryption: Disable mem merge
hw/i386: Rename X86CPUTopoInfo structure to X86CPUTopoIDs
i386: Add 2nd Generation AMD EPYC processors
i386: Add missing cpu feature bits in EPYC model
target/i386: Add new property note to versioned CPU models
target/i386: Add Denverton-v2 (no MPX) CPU model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPUClass has a 'reset' method. This is a legacy from when
TYPE_CPU used not to inherit from TYPE_DEVICE. We don't need it any
more, as we can simply use the TYPE_DEVICE reset. The 'cpu_reset()'
function is kept as the API which most places use to reset a CPU; it
is now a wrapper which calls device_cold_reset() and then the
tracepoint function.
This change should not cause CPU objects to be reset more often
than they are at the moment, because:
* nobody is directly calling device_cold_reset() or
qdev_reset_all() on CPU objects
* no CPU object is on a qbus, so they will not be reset either
by somebody calling qbus_reset_all()/bus_cold_reset(), or
by the main "reset sysbus and everything in the qbus tree"
reset that most devices are reset by
Note that this does not change the need for each machine or whatever
to use qemu_register_reset() to arrange to call cpu_reset() -- that
is necessary because CPU objects are not on any qbus, so they don't
get reset when the qbus tree rooted at the sysbus bus is reset, and
this isn't being changed here.
All the changes to the files under target/ were made using the
included Coccinelle script, except:
(1) the deletion of the now-inaccurate and not terribly useful
"CPUClass::reset" comments was done with a perl one-liner afterwards:
perl -n -i -e '/ CPUClass::reset/ or print' target/*/*.c
(2) this bit of the s390 change was done by hand, because the
Coccinelle script is not sophisticated enough to handle the
parent_reset call being inside another function:
| @@ -96,8 +96,9 @@ static void s390_cpu_reset(CPUState *s, cpu_reset_type type)
| S390CPU *cpu = S390_CPU(s);
| S390CPUClass *scc = S390_CPU_GET_CLASS(cpu);
| CPUS390XState *env = &cpu->env;
|+ DeviceState *dev = DEVICE(s);
|
|- scc->parent_reset(s);
|+ scc->parent_reset(dev);
| cpu->env.sigp_order = 0;
| s390_cpu_set_state(S390_CPU_STATE_STOPPED, cpu);
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200303100511.5498-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of passing a pointer to memory now just extend the GByteArray
to all the read register helpers. They can then safely append their
data through the normal way. We don't bother with this abstraction for
write registers as we have already ensured the buffer being copied
from is the correct size.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-Id: <20200316172155.971-15-alex.bennee@linaro.org>
Convert all targets to use cpu_class_set_parent_reset() with the following
coccinelle script:
@@
type CPUParentClass;
CPUParentClass *pcc;
CPUClass *cc;
identifier parent_fn;
identifier child_fn;
@@
+cpu_class_set_parent_reset(cc, child_fn, &pcc->parent_fn);
-pcc->parent_fn = cc->reset;
...
-cc->reset = child_fn;
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <157650847817.354886.7047137349018460524.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We currently search both the root and the tcg/ directories for tcg
files:
$ git grep '#include "tcg/' | wc -l
28
$ git grep '#include "tcg[^/]' | wc -l
94
To simplify the preprocessor search path, unify by expliciting the
tcg/ directory.
Patch created mechanically by running:
$ for x in \
tcg.h tcg-mo.h tcg-op.h tcg-opc.h \
tcg-op-gvec.h tcg-gvec-desc.h; do \
sed -i "s,#include \"$x\",#include \"tcg/$x\"," \
$(git grep -l "#include \"$x\""); \
done
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200101112303.20724-2-philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The functions generated by these macros are unused.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't actually need the result of the read, only to probe that the
memory mapping exists. This is exactly what probe_access does.
This is also the only user of any cpu_ld*_code_ra function.
Removing this allows the interface to be removed shortly.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Configuration overlay may define MPU background map. Import
core-matmap.h from the overlay and use XCHAL_MPU_BACKGROUND_MAP macro
if it's defined.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Import core-isa.h from its canonical place in the configuration overlay.
Drop --xform option from the tar command line.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Allow ps.ring modification by wsr.ps/xsr.ps and use ps.ring value in
xtensa_get_[c]ring on configurations with MPU.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Overlay part of the test_mmuhifi_c3 core has GPL3 copyright headers in
it. Fix that by regenerating test_mmuhifi_c3 core overlay and
re-importing it.
Fixes: d848ea7767 ("target/xtensa: add test_mmuhifi_c3 core")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Xtensa binaries built for call0 ABI don't rotate register window on
function calls and returns. Invocation of signal handlers from the
kernel is therefore different in windowed and call0 ABIs.
There's currently no way to determine xtensa ELF binary ABI from the
binary itself. Add handler for the -xtensa-abi-call0 command line
parameter/QEMU_XTENSA_ABI_CALL0 envitonment variable to the qemu-user
and record ABI choice. Use it to initialize PS.WOE in xtensa_cpu_reset.
Check PS.WOE in setup_rt_frame to determine how a signal should be
delivered.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20190906165713.5558-1-jcmvbkbc@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
Prior patch resets can_do_io flag at the TB entry. Therefore there is no
need in resetting this flag at the end of the block.
This patch removes redundant gen_io_end calls.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <156404429499.18669.13404064982854123855.stgit@pasha-Precision-3630-Tower>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@gmail.com>
This patch moves the define of target access alignment earlier from
target/foo/cpu.h to configure.
Suggested in Richard Henderson's reply to "[PATCH 1/4] tcg: TCGMemOp is now
accelerator independent MemOp"
Signed-off-by: Tony Nguyen <tony.nguyen@bt.com>
Message-Id: <11e818d38ebc40e986cfa62dd7d0afdc@tpw09926dag18e.domain1.systemhost.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: tony.nguyen@bt.com <tony.nguyen@bt.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-4-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
This macro is now always empty, so remove it. This leaves the
entire contents of CPUArchState under the control of the guest
architecture.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Nothing in there so far, but all of the plumbing done
within the target ArchCPU state.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Consolidate some boilerplate from foo_cpu_initfn.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have ArchCPU, we can define this generically,
in the one place that needs it.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace xtensa_env_get_cpu with env_archcpu. The combination
CPU(xtensa_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Move cpu_get_tb_cpu_state below the include of "exec/cpu-all.h"
so that the definition of env_cpu is available.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have both ArchCPU and CPUArchState, we can define
this generically instead of via macro in each target's cpu.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, do this just before including exec/cpu-all.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, do this just before including exec/cpu-all.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, into this new file move TARGET_LONG_BITS,
TARGET_PAGE_BITS, TARGET_PHYS_ADDR_SPACE_BITS,
TARGET_VIRT_ADDR_SPACE_BITS, and NB_MMU_MODES.
Include this new file from exec/cpu-defs.h.
This now removes the somewhat odd requirement that target/arch/cpu.h
defines TARGET_LONG_BITS before including exec/cpu-defs.h, so push the
bulk of the includes within target/arch/cpu.h to the top.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In preparation for having some more common semihosting code let's
excise the current config magic from vl.c into its own file. We shall
later add more conditionals to the build configurations so we can
avoid building this if we don't need it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Improve tlb_vaddr_to_host for use by ARM SVE no-fault loads.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAlzVx4UdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+U1Af/b3cV5d5a1LWRdLgR
71JCPK/M3o43r2U9wCSikteXkmNBEdEoc5+WRk2SuZFLW/JB1DHDY7/gISPIhfoB
ZIza2TxD/QK1CQ5/mMWruKBlyygbYYZgsYaaNsMJRJgicgOSjTN0nuHMbIfv3tAN
mu+IlkD0LdhVjP0fz30Jpew3b3575RCjYxEPM6KQI3RxtQFjZ3FhqV5hKR4vtdP5
yLWJQzwAbaCB3SZUvvp7TN1ZsmeyLpc+Yz/YtRTqQedo7SNWWBKldLhqq4bZnH1I
AkzHbtWIOBrjWJ34ZMAgI5Q56Du9TBbBvCdM9azmrQjSu/2kdsPBPcUyOpnUCsCx
NyXo9g==
=x71l
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-tcg-20190510' into staging
Add CPUClass::tlb_fill.
Improve tlb_vaddr_to_host for use by ARM SVE no-fault loads.
# gpg: Signature made Fri 10 May 2019 19:48:37 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-tcg-20190510: (27 commits)
tcg: Use tlb_fill probe from tlb_vaddr_to_host
tcg: Remove CPUClass::handle_mmu_fault
tcg: Use CPUClass::tlb_fill in cputlb.c
target/xtensa: Convert to CPUClass::tlb_fill
target/unicore32: Convert to CPUClass::tlb_fill
target/tricore: Convert to CPUClass::tlb_fill
target/tilegx: Convert to CPUClass::tlb_fill
target/sparc: Convert to CPUClass::tlb_fill
target/sh4: Convert to CPUClass::tlb_fill
target/s390x: Convert to CPUClass::tlb_fill
target/riscv: Convert to CPUClass::tlb_fill
target/ppc: Convert to CPUClass::tlb_fill
target/openrisc: Convert to CPUClass::tlb_fill
target/nios2: Convert to CPUClass::tlb_fill
target/moxie: Convert to CPUClass::tlb_fill
target/mips: Convert to CPUClass::tlb_fill
target/mips: Tidy control flow in mips_cpu_handle_mmu_fault
target/mips: Pass a valid error to raise_mmu_exception for user-only
target/microblaze: Convert to CPUClass::tlb_fill
target/m68k: Convert to CPUClass::tlb_fill
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exclusive Instructions provide a general-purpose mechanism for
atomic updates of memory-based synchronization variables that can be
used for exclusion algorithms.
Use cmpxchg-based implementation that is sufficient for the typical use
of exclusive access in atomic operations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Block prefetch option adds a bunch of non-privileged opcodes that may be
implemented as nops since QEMU doesn't model caches.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-9-armbru@redhat.com>
scripts/clean-header-guards.pl warns these headers use reserved
identifier _XTENSA_CORE_CONFIGURATION_H as header guard symbol. It
additionally warns the guard doesn't match the file name.
Reuse of the same guard symbol in multiple headers is okay as long as
they cannot be included together.
Since we can avoid guard symbol reuse easily, do so: use the guard
symbol scripts/clean-header-guards.pl picks, less the TARGET_ prefix.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-5-armbru@redhat.com>
The Memory Protection Unit Option (MPU) is a combined instruction and
data memory protection unit with more protection flexibility than the
Region Protection Option or the Region Translation Option but without
any translation capability. It does no demand paging and does not
reference a memory-based page table.
Add memory protection unit option, internal state, SRs and opcodes.
Implement MPU entries dumping in dump_mmu.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add SRs and rsr/wsr/xsr opcodes defined by the parity/ECC xtensa option.
The implementation is trivial since we don't emulate parity/ECC yet.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
IDMA and scatter/gather features introduced new IRQ types that
overlay_tool.h need to initialize Xtensa configuration.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Remove declarations of the internal mmu_helper functions from the cpu.h,
make these functions static and shuffle them.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
SR numbers are not unique: different Xtensa options may reuse SR number
for different purposes. Introduce generic rsr/wsr functions and xsr
template and use them instead of centralized SR access functions. Change
prototypes of specific rsr/wsr functions to match XtensaOpcodeOp and use
them instead of centralized SR access functions. Put xtensa option that
introduces SR into the second opcode description parameter and use it to
test for rsr/wsr/xsr opcode validity. Extract SR and UR names for the
xtensa_cpu_dump_state from libisa. Merge SRs and URs in the dump.
Register names of used SR/UR in init_libisa and use these names for TCG
globals referencing these SR/UR.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
We can now use the CPUClass hook instead of a named function.
Create a static tlb_fill function to avoid other changes within
cputlb.c. This also isolates the asserts within. Remove the
named tlb_fill function from all of the targets.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In order to handle TB's that translate to too much code, we
need to place the control of the length of the translation
in the hands of the code gen master loop.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
CPUClass method dump_statistics() takes an fprintf()-like callback and
a FILE * to pass to it. Most callers pass fprintf() and stderr.
log_cpu_state() passes fprintf() and qemu_log_file.
hmp_info_registers() passes monitor_fprintf() and the current monitor
cast to FILE *. monitor_fprintf() casts it right back, and is
otherwise identical to monitor_printf().
The callback gets passed around a lot, which is tiresome. The
type-punning around monitor_fprintf() is ugly.
Drop the callback, and call qemu_fprintf() instead. Also gets rid of
the type-punning, since qemu_fprintf() takes NULL instead of the
current monitor cast to FILE *.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-15-armbru@redhat.com>
The various dump_mmu() take an fprintf()-like callback and a FILE * to
pass to it, and so do their helper functions. Passing around callback
and argument is rather tiresome.
Most dump_mmu() are called only by the target's hmp_info_tlb(). These
all pass monitor_printf() cast to fprintf_function and the current
monitor cast to FILE *.
SPARC's dump_mmu() gets also called from target/sparc/ldst_helper.c a
few times #ifdef DEBUG_MMU. These calls pass fprintf() and stdout.
The type-punning is technically undefined behaviour, but works in
practice. Clean up: drop the callback, and call qemu_printf()
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-11-armbru@redhat.com>
The various TARGET_cpu_list() take an fprintf()-like callback and a
FILE * to pass to it. Their callers (vl.c's main() via list_cpus(),
bsd-user/main.c's main(), linux-user/main.c's main()) all pass
fprintf() and stdout. Thus, the flexibility provided by the (rather
tiresome) indirection isn't actually used.
Drop the callback, and call qemu_printf() instead.
Calling printf() would also work, but would make the code unsuitable
for monitor context without making it simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417191805.28198-10-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Don't announce that exit simcall has been invoked: this is just noise.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
break_dependency incorrectly handles the case of dependency on an opcode
that references the same register multiple times. E.g. the following
instruction is translated incorrectly:
{ or a2, a3, a3 ; or a3, a2, a2 }
This happens because resource indices of both dependency graph nodes are
incremented, and a copy for the second instance of the same register in
the ending node is not done.
Only increment resource index of the ending node of the dependency.
Add test.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Load/store opcodes may raise MMU exceptions. Normally exceptions should
be checked in priority order before any actual operations, but since MMU
exceptions are tightly coupled with actual memory access, there's
currently no way to do it.
Approximate this behavior by executing all load, then all store, and
then all other opcodes in the FLIX bundles. Use opcode dependency
mechanism to express ordering. Mark load/store opcodes with
XTENSA_OP_{LOAD,STORE} flags. Newer libisa has classifier functions that
can tell whether opcode is a load or store, but this information is not
available in the existing overlays.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Currently topologic opcode sorting stops at the first detected
dependency loop. Introduce struct opcode_arg_copy that describes
temporary register copy. Scan remaining opcodes searching for
dependencies that can be broken, break them by introducing temporary
register copies and record them in an array. In case of success
create local temporaries and initialize them with current register
values. Share single temporary copy between all register users. Delete
temporaries after translation.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
libisa represents boolean registers b0..b16 as a BR register file and as
BR4 and BR8 register groups. Add these register files and use
OpcodeArg::{in,out} parameters to access boolean registers in
translators.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
libisa represents MAC16 registers m0..m3 as an MR register file. Add
this register file and reference its registers directly from the
translate_mac16. Drop translator parameter that indicates whether opcode
argument is in ar or in mr.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
To support circular register dependencies in FLIX bundles opcode inputs
and outputs must be separate and adjustable. Circular dependencies can
be broken by making temporary copies of opcode inputs and substituting
them into the arguments array instead of the original registers.
E.g. the circular register dependency in the following bundle:
{ mov a2, a3 ; mov a3, a2 }
can be resolved by making copy a2' = a2 and substituting it as input
argument of the second opcode:
{ mov a2, a3 ; mov a3, a2' }
Change opcode translator prototype to accept OpcodeArg array as
argument. For each register argument initialize OpcodeArg::{in,out} with
TCGv_* of the respective register. Don't explicitly use cpu_R in the
opcode translators, use OpcodeArg::{in,out} instead.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move return address calculation and WINDOW_START adjustment out of the
retw helper to simplify logic a bit and avoid using registers directly.
Pass a0 as a parameter to the helper.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Opcodes that modify WINDOW_BASE SR don't have dependency on opcodes that
use windowed registers. If such opcodes are combined in a single
instruction they may not be correctly ordered. Instead of adding said
dependency use temporary register to store changed WINDOW_BASE value and
do actual register window rotation as a postprocessing step.
Not all opcodes that change WINDOW_BASE need this: retw, rfwo and rfwu
are also jump opcodes, so they are guaranteed to be translated last and
thus will not affect other opcodes in the same instruction.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Some opcodes may need additional actions at every exit from the
translated instruction or may need to amend TB exit slots available to
jumps generated for the instruction. Add gen_postprocess function and
call it from the gen_jump_slot and from the disas_xtensa_insn.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Opcodes in different slots may read and write same resources (registers,
states). In the absence of resource dependency loops it must be possible
to sort opcodes to avoid interference.
Record resources used by each opcode in the bundle. Build opcode
dependency graph and use topological sort to order its nodes. In case of
success translate opcodes in sort order. In case of failure report and
raise invalid opcode exception.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
FLIX adds branch and loop instruction variants with 15- and 18-bit wide
target offset. Implement them as additional names for the ordinary
branch/loop opcodes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There are opcodes that differ only in encoding or possible range of
immediate arguments. Allow multiple names for single opcode translation
table entry to reduce code duplication in that case.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Requirement for alphabetical opcode sorting in opcode tables is awkward
and does not allow sharing implementation between multiple opcodes.
Use hash tables to find opcodes by name. Move implementation from the
translate.c to the helper.c to its only user and remove declaration from
the cpu.h
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Don't run xtensa_finalize_config at the time of core registration,
instead run it at the CPU class initialization.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
xtensa-modules part of the test_mmuhifi_c3 core is missing fixes that
returns XTENSA_UNDEFINED for undefined opcodes and marks all data
structures static. Run sed script from target/xtensa/import_core.sh on
it. This fixes test_sr tests for missing special registers.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Merge gen_callwi and gen_callw into their only users, translate_callw
and translate_callxw. Extract jump slot adjustment logic into a separate
function and use it in gen_jumpi and translate_callw.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Use libisa to extract whether opcode uses windowed registers and
construct mask based on that. This only leaves special case for the
'entry' opcode, as it needs to probe a register dynamically.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
xtensa-modules.c produced by recent Tensilica tools have
Opcode_*_encode_fns arrays defined as static. Don't add extra 'static'
in front of them when importing.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Runstall signal looks very much like a level-triggered IRQ line. Provide
xtensa_get_runstall function that returns runstall IRQ.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Replace xtensa_get_extint that returns single external IRQ descriptor
with xtensa_get_extints that returns a vector of all external IRQs.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
It's a one-liner used in a single place, move its implementation there
and remove its declaration.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
INTERRUPT special register may be changed both by the core (by writing
to INTSET and INTCLEAR registers) and by external events (by triggering
and clearing HW IRQs). In MTTCG this state must be protected from
concurrent access, otherwise interrupts may be lost or spurious
interrupts may be detected.
Use atomic operations to change INTSET SR.
Fix wsr.intset so that it soesn't clear any bits.
Fix wsr.intclear so that it doesn't clear bit that corresponds to NMI.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
When xtensa_runstall is called to unstall a core it needs to kick it
after clearing runstall flag, otherwise the core doesn't start
immediately. There's also no point in clearing CPU_INTERRUPT_HALT, drop
it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move helper functions related to interrupt and exception handling from
op_helper.c and helper.c to exc_helper.c. No functional changes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move HELPER functions related to native debugging from op_helper.c to
dbg_helper.c. No functional changes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move MMU-related helper functions from op_helper.c and helper.c to
mmu_helper.c. No functional changes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move helper functions related to register windows from op_helper.c to
win_helper.c. No functional changes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Don't invalidate TB with the end of zero overhead loop when LBEG or LEND
change. Instead encode the distance from the start of the page where the
TB starts to the LEND in the TB cs_base and generate loopback code when
the next PC matches encoded LEND. Distance to a destination within the
same page and up to a maximum instruction length into the next page is
encoded literally, otherwise it's zero. The distance from LEND to LBEG
is also encoded in the cs_base: it's encoded literally when less than
256 or as 0 otherwise. This allows for TB chaining for the loopback
branch at the end of a loop for the most common loop sizes.
With this change the resulting emulation speed is about 10% higher in
softmmu mode on uClibc-ng and LTP tests. Emulation speed in linux
user mode is a few percent lower because there's no direct TB chaining
between different memory pages. Testing with lower limit on direct TB
chaining range shows gradual slowdown to ~15% for the block size of 64
bytes and ~50% for the block size of 32 bytes.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Now that xtensa_count_regs does the right thing, remove manual
initialization of these fields from the affected configurations and let
xtensa_finalize_config initialize them. Add XTREG_END to terminate
register lists.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
In order to communicate correctly with gdb xtensa gdbstub must provide
expected number of registers in 'g' packet response. xtensa-elf-gdb
expects both nonprivileged and privileged registers. xtensa-linux-gdb
only expects nonprivileged registers. gdb only counts one contiguous
stretch of registers, do the same for the core registers in the
xtensa_count_regs.
With this change qemu-system-xtensa is able to communicate with all
xtensa-elf-gdb versions (versions prior to 8.2 require overlay fixup),
and qemu-xtensa is able to communicate with all xtensa-linux-gdb
versions, except 8.2.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark instructions that affect active IRQ level;
- put call for gen_check_interrupts right after the instruction
translation; when FLIX is enabled it will need to appear before
other exits from the TB as well;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Now that all logic for TB termination is extracted from rsr/wsr their
return value is not used and may be dropped.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark instructions that require TB termination via slot 0;
- put TB termination right after the instruction translation loop, if
termination w/o TB linking wasn't requested;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Currently we only end TB in icount mode, because access to CCOUNT or
write to CCOMPARE are IO operations. Simplify the behaviour a bit and
end TB unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Opcode decoding with libisa takes care about range of valid group SRs,
like CCOMPARE, IBREAKA, DBREAKA or DBREAKC. Turn range checks in wsr
implementations into assertions.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark all instructions that exit TB and require dynamic search for the
next TB;
- put TB termination right after the instruction translation loop;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark quos/quou/rems/remu instructions;
- drop parameter 0 from the translate_quou and split translate_remu from
it;
- put test for division by zero exception right after the coprocessor
exception test;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- add XtensaOpcodeOps::coprocessor with bitmask of coprocessors used by
the instruction;
- replace coprocessor id parameter of gen_check_cpenable with the
bitmask of used coprocessors;
- collect coprocessor IDs used by an instruction in the disassembly
loop;
- put test for coprocessor disabled exception after the alloca test;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark retw and retw.n instructions;
- extract window inderflow test from retw helper;
- put underflow exception check generation right after the overflow
check;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- add ps.callinc to the TB flags, that allows testing all instructions
for window overflow statically;
- drop gen_window_check* functions; replace them with get_window_check
that accepts bitmask of used registers;
- add XtensaOpcodeOps::test_overflow that returns bitmask of implicitly
used registers; use it for entry and call{,x}{4,8,12};
- drop window overflow test from the entry helper;
- drop parameter 0 from translate_[di]cache and use translate_nop for
d/i cache opcodes that don't need memory accessibility check;
- add bitmask XtensaOpcodeOps::windowed_register_op that marks opcode
arguments that refer to windowed registers;
- translate windowed_register_op mask to a mask of actually used
registers in the disassembly loop;
- add check for window overflow right after the check for debug
exception;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark break and break.n instructions;
- collect debug cause bits from parameter 0 of instructions marked for
debug exception;
- put debug exception check right after syscall check;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mark privileged instructions;
- put single privileged instruction check after disassembly loop;
- translate_[di]cache: drop parameter 0, shift parameters one down;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- TB flags: add XTENSA_TBFLAG_CWOE that corresponds to the architectural
CWOE state;
- entry: move CWOE check from the helper to the test_ill_entry;
- retw: move CWOE check from the helper to the test_ill_retw;
- separate instruction disassembly loop and translation loop; save
disassembly results in local array;
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Complete xtensa-semi chardev console implementation: allow reading input
characters from file descriptor 0 and call sys_select_one simcall on it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
s32c1i must load and store value with target endianness, not host.
This results in an infinite loop in atomic cmpxchg sequences when target
endianness doesn't match host endianness.
Fixes: 9fb40342d4 ("target/xtensa: support MTTCG")
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
- FPU2000 defines rfr and wfr opcodes, not rfr.s and wfr.s;
- movcond.s uses incorrect operand in tcg_gen_movcond: in case the
condition is not satisfied it must not change its argument 0.
Fixes: c04e1692e3 ("target/xtensa: extract FPU2000 opcode
translators")
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- move register counting to xtensa/gdbstub.c
- add symbolic names for register types and flags from GDB and use them
in register counting and access functions.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This fixes communication with gdb in the presence of type-5 (TIE state
mapped on user registers) and type-7 (special case of masked registers)
registers in the xtensa core config.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The instance_init function of the xtensa CPUs creates a memory region,
but does not set an owner, so the memory region is not destroyed
correctly when the CPU object is removed. This can happen when
introspecting the CPU devices, so introspecting the CPU device will
leave a dangling memory region object in the QOM tree. Make sure to
set the right owner here to fix this issue.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-id: 1532005320-17794-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The xtensa frontend calls get_page_addr_code() from its
itlb_hit_test helper function. This function is really part
of the TCG core's internals, and calling it from a target
helper makes it awkward to make changes to that core code.
It also means that we don't pass the correct retaddr to
tlb_fill(), so we won't correctly handle the case where
an exception is generated.
The helper is used for the instructions IHI, IHU and IPFL.
Change it to call cpu_ldb_code_ra() instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will reduce the size of the patch in the next patch,
where the context will have to be a pointer.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The usage of DISAS_UPDATE is after noreturn helpers.
It is thus indistinguishable from DISAS_NORETURN.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
ISA book documents that the first instruction of zero overhead loop
must fit completely into naturally aligned region of an instruction
fetch unit size. Check that condition and log a message if it's
violated.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Place them in exec.c, exec-all.h and ram_addr.h. This removes
knowledge of translate-all.h (which is an internal header) from
several files outside accel/tcg and removes knowledge of
AddressSpace from translate-all.c (as it only operates on ram_addr_t).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-id: 20180606152128.449-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do the cast to uintptr_t within the helper, so that the compiler
can type check the pointer argument. We can also do some more
sanity checking of the index argument.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since d0ce7e9cfc the dc232b structure uses the NANOSECONDS_PER_SECOND
definition from "qemu/timer.h". Include it to allow further includes
cleanup.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-7-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to tb_invalidate_phys_addr().
Its callers either have an attrs value to hand, or don't care
and can use MEMTXATTRS_UNSPECIFIED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180521140402.23318-3-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAlsBEgAPHG1qdEB0bHMu
bXNrLnJ1AAoJEHAbT2saaT5Z74oH/1rKw64XSout5P3RNbhy8LjDfhu/wxtda8oR
I3e/KbAOsmdU956Bvzk9eiL6gYyG2LrXgY5mJYaY5b+IwRZZEoywRvUX042fSEU0
Hdkrjx8MpAVPN0RztLM2UDQta2NPv9uBc/X9tMR+brRnLID6qXDdd1tjKG5e8vDt
iAfEgGdSg1opJlEyhOI3EPokdGa0QnrBgdPnEqhxtTWNhWWPxbdRVVTeyzJYOztC
sM647Ca6P5y+0lBQNB4CXydiAR0GnE/SS1krFWbrpuI6rbOwzBOsPTi84JtwQzv+
VWjmXfjnXy5c0+DG93e0sS6vqJF4V2ZoHKca2VVzLcBFPUxmZPw=
=MQI4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mjt/tags/trivial-patches-fetch' into staging
trivial patches for 2018-05-20
# gpg: Signature made Sun 20 May 2018 07:13:20 BST
# gpg: using RSA key 701B4F6B1A693E59
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* remotes/mjt/tags/trivial-patches-fetch: (22 commits)
acpi: fix a comment about aml_call0()
qapi/net.json: Fix the version number of the "vlan" removal
gdbstub: Handle errors in gdb_accept()
gdbstub: Use qemu_set_cloexec()
replace functions which are only available in glib-2.24
typedefs: Remove PcGuestInfo from qemu/typedefs.h
qemu-options: Allow -no-user-config again
hw/timer/mt48t59: Fix bit-rotten NVRAM_PRINTF format strings
Remove unnecessary variables for function return value
trivial: Do not include pci.h if it is not necessary
tests: fix tpm-crb tpm-tis tests race
hw/ide/ahci: Keep ALLWINNER_AHCI() macro internal
qemu-img-cmds.hx: add passive-aggressive note
qemu-img: Make documentation between .texi and .hx consistent
qemu-img: remove references to GEN_DOCS
qemu-img.texi: fix command ordering
qemu-img-commands.hx: argument ordering fixups
HACKING: document preference for g_new instead of g_malloc
qemu-option-trace: -trace enable= is a pattern, not a file
slirp/debug: Print IP addresses in human readable form
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* hw/arm/iotkit.c: fix minor memory leak
* softfloat: fix wrong-exception-flags bug for multiply-add corner case
* arm: isolate and clean up DTB generation
* implement Arm v8.1-Atomics extension
* Fix some bugs and missing instructions in the v8.2-FP16 extension
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uXY+
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180510' into staging
target-arm queue:
* hw/arm/iotkit.c: fix minor memory leak
* softfloat: fix wrong-exception-flags bug for multiply-add corner case
* arm: isolate and clean up DTB generation
* implement Arm v8.1-Atomics extension
* Fix some bugs and missing instructions in the v8.2-FP16 extension
# gpg: Signature made Thu 10 May 2018 18:44:34 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180510: (21 commits)
target/arm: Clear SVE high bits for FMOV
target/arm: Fix float16 to/from int16
target/arm: Implement vector shifted FCVT for fp16
target/arm: Implement vector shifted SCVF/UCVF for fp16
target/arm: Enable ARM_FEATURE_V8_ATOMICS for user-only
target/arm: Implement CAS and CASP
target/arm: Fill in disas_ldst_atomic
target/arm: Introduce ARM_FEATURE_V8_ATOMICS and initial decode
target/riscv: Use new atomic min/max expanders
tcg: Use GEN_ATOMIC_HELPER_FN for opposite endian atomic add
tcg: Introduce atomic helpers for integer min/max
target/xtensa: Use new min/max expanders
target/arm: Use new min/max expanders
tcg: Introduce helpers for integer min/max
atomic.h: Work around gcc spurious "unused value" warning
make sure that we aren't overwriting mc->get_hotplug_handler by accident
arm/boot: split load_dtb() from arm_load_kernel()
platform-bus-device: use device plug callback instead of machine_done notifier
pc: simplify MachineClass::get_hotplug_handler handling
softfloat: Handle default NaN mode after pickNaNMulAdd, not before
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# target/riscv/translate.c
The generic expanders replace nearly identical code in the translator.
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180508151437.4232-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the PC is in the last page of the address space, next_page_start
overflows to 0. Fix it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In icount mode, instructions that access io memory spaces in the middle
of the translation block invoke TB recompilation. After recompilation,
such instructions become last in the TB and are allowed to access io
memory spaces.
When the code includes instruction like i386 'xchg eax, 0xffffd080'
which accesses APIC, QEMU goes into an infinite loop of the recompilation.
This instruction includes two memory accesses - one read and one write.
After the first access, APIC calls cpu_report_tpr_access, which restores
the CPU state to get the current eip. But cpu_restore_state_from_tb
resets the cpu->can_do_io flag which makes the second memory access invalid.
Therefore the second memory access causes a recompilation of the block.
Then these operations repeat again and again.
This patch moves resetting cpu->can_do_io flag from
cpu_restore_state_from_tb to cpu_loop_exit* functions.
It also adds a parameter for cpu_restore_state which controls restoring
icount. There is no need to restore icount when we only query CPU state
without breaking the TB. Restoring it in such cases leads to the
incorrect flow of the virtual time.
In most cases new parameter is true (icount should be recalculated).
But there are two cases in i386 and openrisc when the CPU state is only
queried without the need to break the TB. This patch fixes both of
these cases.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <20180409091320.12504.35329.stgit@pasha-VirtualBox>
[rth: Make can_do_io setting unconditional; move from cpu_exec;
make cpu_loop_exit_{noexc,restore} call cpu_loop_exit.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The value of CCOUNT special register is calculated as time elapsed
since CCOUNT == 0 multiplied by the core frequency. In icount mode time
increment between consecutive instructions that don't involve time
warps is constant, but unless the result of multiplication of this
constant by the core frequency is a whole number the CCOUNT increment
between these instructions may not be constant. E.g. with icount=7 each
instruction takes 128ns, with core clock of 10MHz CCOUNT values for
consecutive instructions are:
502: (128 * 502 * 10000000) / 1000000000 = 642.56
503: (128 * 503 * 10000000) / 1000000000 = 643.84
504: (128 * 504 * 10000000) / 1000000000 = 645.12
I.e.the CCOUNT increments depend on the absolute time. This results in
varying CCOUNT differences for consecutive instructions in tests that
involve time warps and don't set CCOUNT explicitly.
Change frequency of the core used in tests so that clock cycle takes
exactly 64ns. Change icount power used in tests to 6, so that each
instruction takes exactly 1 clock cycle. With these changes CCOUNT
increments only depend on the number of executed instructions and that's
what timer tests expect, so they work correctly.
Longer story:
http://lists.nongnu.org/archive/html/qemu-devel/2018-03/msg04326.html
Cc: Pavel Dovgaluk <Pavel.Dovgaluk@ispras.ru>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Change #include <xtensa-isa.h> to #include "xtensa-isa.h" in imported
files to make references to local files consistent.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fix definitions of existing cores and core importing script to follow
the rule of naming non-top level source files.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
cpu_init(cpu_model) were replaced by cpu_create(cpu_type) so
no users are left, remove it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-6-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will be used for providing to cpu name resolving class for
parsing cpu model for system and user emulation code.
Along with change add target to null-machine tests, so
that when switch to CPU_RESOLVING_TYPE happens,
it would ensure that null-machine usecase still works.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu> (m68k)
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> (tricore)
Message-Id: <1518000027-274608-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added macro to riscv too]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Import list of syscalls from the kernel source. Conditionalize code/data
that is only used with softmmu. Implement exception handlers. Implement
signal hander (only the core registers for now, no coprocessors or TIE).
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- emit TCG barriers for MEMW, EXTW, S32RI and L32AI;
- do atomic_cmpxchg_i32 for S32C1I.
Cc: Emilio G. Cota <cota@braap.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
System emulation should provide access to all registers, userspace
emulation should only provide access to unprivileged registers.
Record register flags from GDB register map definition, calculate both
num_regs and num_core_regs if either is zero. Use num_regs in system
emulation, num_core_regs in userspace emulation gdbstub.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add arrows that mark beginning of register windows and position of the
current window in the windowed register file.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
xtensa_cpu_dump_state outputs CPU physical registers as is, without
synchronization from current window. That may result in different values
printed for the current window and corresponding physical registers.
Synchronize physical registers from window before dumping.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
As cpu.h is another typically widely included file which doesn't need
full access to the softfloat API we can remove the includes from here
as well. Where they do need types it's typically for float_status and
the rounding modes so we move that to softfloat-types.h as well.
As a result of not having softfloat in every cpu.h call we now need to
add it to various helpers that do need the full softfloat.h
definitions.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[For PPC parts]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the change
to target/s390x/gen-features.c manually reverted, and blank lines
around deletions collapsed.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-3-armbru@redhat.com>
System headers should be included with <...>, our own headers with
"...". Offenders tracked down with an ugly, brittle and probably
buggy Perl script. Previous iteration was commit a9c94277f0.
Delete inclusions of "string.h" and "strings.h" instead of fixing them
to <string.h> and <strings.h>, because we always include these via
osdep.h.
Put the cleaned up system header includes first.
While there, separate #include from file comment with exactly one
blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-2-armbru@redhat.com>
The MC68040 MMU provides the size of the access that
triggers the page fault.
This size is set in the Special Status Word which
is written in the stack frame of the access fault
exception.
So we need the size in m68k_cpu_unassigned_access() and
m68k_cpu_handle_mmu_fault().
To be able to do that, this patch modifies the prototype of
handle_mmu_fault handler, tlb_fill() and probe_write().
do_unassigned_access() already includes a size parameter.
This patch also updates handle_mmu_fault handlers and
tlb_fill() of all targets (only parameter, no code change).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20180118193846.24953-2-laurent@vivier.eu>
Coverity warnings CID 1385146, 1385148 1385149 and 1385150 point that
xtensa_opcode_num_operands and xtensa_format_num_slots may return -1
even when xtensa_opcode_decode and xtensa_format_decode succeed. In that
case unsigned counters used to iterate through operands/slots will not
do the right thing.
Make counters and loop bounds signed to fix the warnings.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The sample_controller core is a simple noMMU general purpose core, modern
analog of de212. It is used as a default core in the xtensa port of
Zephyr.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Define default core for noMMU configurations and use that core as
machine default with noMMU XTFPGA machines.
This is done to avoid offering non-working configuration (MMU core on a
noMMU machine) as a default.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Some older versions of gcc complain if a typedef is defined twice:
target/xtensa/translate.c:81: error: redefinition of typedef 'DisasContext'
target/xtensa/cpu.h:339: note: previous declaration of 'DisasContext' was here
Remove the now-redundant typedef from the definition of the struct in
translate.c.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1515762528-22818-1-git-send-email-peter.maydell@linaro.org
DE212 is a noMMU core supported in linux. Import this core to provide
true noMMU configuration for xtensa linux to run on QEMU.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
const16 is an opcode that shifts 16 lower bits of an address register
to the 16 upper bits and puts its immediate operand into the lower 16
bits. It is not controlled by an Xtensa option and doesn't have a fixed
opcode.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
GPIO32 is not in the core ISA, but it was widely used in Diamond Cores.
This implementation doesn't do actual I/O and doesn't handle the case of
GPIO32 state being a part of coprocessor.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add two special registers: MMID and DDR:
- MMID is write-only and the only side effect of writing to it is output
to the trace port, which is not emulated;
- DDR is only accessible in debug mode, which is not emulated.
Add two debug-mode-only opcodes:
- rfdd and rfdo do return from the debug mode, which is not emulated.
Add three internal opcodes for full MMU:
- hwwdtlba and hwwitlba are the internal opcodes that write a value into
autoupdate DTLB or ITLB entry.
- ldpte is internal opcode that loads PTE entry that covers the most
recent page fault address.
None of these three opcodes may appear in a valid instruction.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
It doesn't help much, always-set bit 0 of the LITBASE SR is easy to
compensate with decrement of the l32r immediate argument.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Replace manual opcode analysis with libisa-based code. This makes it
possible to support variable-encoding instructions of the core ISA, like
const16, and will allow to support advanced Xtensa features, like FLIX
and TIE.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
FPU2000 implements basic single-precision floating point operations and
can be replaced with a different implementation, like DFPU or HiFi. Move
FPU2000 opcode translators into separate functions and list them in a
separate array.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Move implementations of core opcodes into separate translation
functions. Introduce data structures for mapping opcode name to
translator function. Make an array of core opcode/translator structures.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The canonical way of dealing with Xtensa instructions decoding and
encoding is through the libisa. Libisa is a configuration-independent
library with a stable interface plus generated configuration-specific
xtensa-modules.c file with implementations of decoding and encoding
functions. Libisa is MIT-licensed and originally disributed
xtensa-modules.c files are also MIT-licensed and are available as a
part of xtensa configuration overlay.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Currently 'entry' opcode helper accepts frame size divided by 8, as it
is encoded in the opcode. Make it more natural and accept actual frame
size instead.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
use new XTENSA_CPU_TYPE_NAME to compose CPU type name
to bring xtensa in line with all other targets that
will similar macro.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1507211474-188400-25-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Now that every target is using the disas_set_info hook,
the flags argument is unused. Remove it.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is identical for each target. So, move the initialization to
common code. Move the variable itself out of tcg_ctx and name it
cpu_env to minimize changes within targets.
This also means we can remove tcg_global_reg_new_{ptr,i32,i64},
since there are no longer global-register temps created by targets.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Groundwork for supporting multiple TCG contexts.
The core of this patch is this change to tcg/tcg.h:
> -extern TCGContext tcg_ctx;
> +extern TCGContext tcg_init_ctx;
> +extern TCGContext *tcg_ctx;
Note that for now we set *tcg_ctx to whatever TCGContext is passed
to tcg_context_init -- in this case &tcg_init_ctx.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Convert all existing readers of tb->cflags to tb_cflags, so that we
use atomic_read and therefore avoid undefined behaviour in C11.
Note that the remaining setters/getters of the field are protected
by tb_lock, and therefore do not need conversion.
Luckily all readers access the field via 'tb->cflags' (so no foo.cflags,
bar->cflags in the code base), which makes the conversion easily
scriptable:
FILES=$(git grep 'tb->cflags' target include/exec/gen-icount.h \
accel/tcg/translator.c | cut -f1 -d':' | sort | uniq)
perl -pi -e 's/([^.>])tb->cflags/$1tb_cflags(tb)/g' $FILES
perl -pi -e 's/([a-z->.]*)(->|\.)tb->cflags/tb_cflags($1$2tb)/g' $FILES
Then manually fixed the few errors that checkpatch reported.
Compile-tested for all targets.
Suggested-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move target cpu tcg initialization to common code,
called from cpu_exec_realizefn.
Acked-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Instead of using the hardcoded (MemTxAttrs){0} for no memory attributes
let's use the already defined MEMTXATTRS_UNSPECIFIED macro instead.
This is technically a change of behaviour as MEMTXATTRS_UNSPECIFIED sets
the unspecified field to 1, but it doesn't look like anything is
checking this field.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Used later. An enum makes expected values explicit and
bounds the value space of switches.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <150002049746.22386.2316077281615710615.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
call xtensa_irq_init() at realize time which makes
cpu_xtensa_init() like generic cpu creation function.
As result we can replace it with cpu_generic_init()
which does the same job, reducing code duplication a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-16-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Needed to implement a target-agnostic gen_intermediate_code()
in the future.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002025498.22386.18051908483085660588.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xtensa cores may have registers of types/sizes not supported by the
gdbstub accessors. Ignore writes to such registers and return zero on
read, but always return correct register size, so that gdb on the other
side is able to access all registers in the packet holding unsupported
registers in the middle. This fixes gdb interaction with cores that have
vector/custom TIE registers.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
In semihosting mode QEMU allows guest to read and write host file
descriptors directly, including descriptors 0..2, a.k.a. stdin, stdout
and stderr. Sometimes it's desirable to have semihosting console
controlled by -serial option, e.g. to connect it to network.
Add semihosting console to xtensa-semi.c, open it in the 'sim' machine
in the presence of -serial option and direct stdout and stderr to it
when it's present.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Return value of read/write simcalls is not calculated correctly in case
of operations crossing page boundary and in case of short reads/writes.
Read and write simcalls should return the size of data actually
read/written or -1 in case of error.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Read and write simcalls map physical memory to access I/O buffers, but
'read' simcall need to map it for writing and 'write' simcall need to
map it for reading, i.e. the opposite of what they do now. Fix that.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
So far xtensa provides fixed dummy argc/argv for the corresponding
semihosting calls. Now that there are semihosting_get_argc and
semihosting_get_arg, use them to pass actual command line arguments
to guest.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Make sure we have the BQL held when processing interrupts.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
