When using "--without-default-devices", the ARM_GICV3_TCG and ARM_GIC_KVM
settings currently get disabled, though the arm virt machine is only of
very limited use in that case. This also causes the migration-test to
fail in such builds. Let's make sure that we always keep the GIC switches
enabled in the --without-default-devices builds, too.
Message-ID: <20240221110059.152665-1-thuth@redhat.com>
Tested-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Now there is an ncpus property, use it in order to deliver the IRQ to
multiple CPU.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-5-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This implements the multiprocessor status register in grlib-irqmp and
bind it to a start signal, which will be later wired in leon3-generic
to start a cpu.
The EIRQ and BA bits are not implemented.
Based on https://gaisler.com/doc/gr712rc-usermanual.pdf, §8.3.5.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-4-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This adds a "ncpus" property to the "grlib-irqmp" device to be used
later, this required a little refactoring of how we initialize the
device (ie: use realize instead of init).
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-3-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Split out the headers for each peripherals and move them in their
right hardware directory.
Update Copyright and add SPDX-License-Identifier at the same time.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-2-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
/dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
+Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
=K4b1
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user-snd support
x2APIC mode with TCG support
CXL update to r3.1
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXMoXUPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpFtMIAKUKD0hzJrwOyPo4xsRUMbsB3ehIsJsMKfOK
# w+JWzTaojAG8ENPelWBdL2sEIs5U73VOchjLqHbH2m5sz6GJ13214amvdU/fYc8+
# /dU2ZKoAmaR5L1ovKO/fq07y/J6DrITZ5tosy2i84Xa8EnsL4j3wEPNVWsDi7dna
# mvXUICSOOoJQ4O2YhSruKCQ8qIgF1/0Oi3u/rcrW3alSs8VQlrtQXxl6k+LbYqek
# +Fytco3jMRHPvQ+GYUIwGuHjN15ghArcvbsV0GIa+24BPY5h7YbDYGbfasePT5OK
# zDz51jitkoyDrQr+OzwOEe/X5+dVGhayRXfMtU5Qm53IE3y61qc=
# =K4b1
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 14 Feb 2024 11:18:13 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (60 commits)
MAINTAINERS: Switch to my Enfabrica email
virtio-gpu-rutabaga.c: override resource_destroy method
virtio-gpu.c: add resource_destroy class method
hw/display/virtio-gpu.c: use reset_bh class method
hw/smbios: Fix port connector option validation
hw/smbios: Fix OEM strings table option validation
virtio-gpu: Correct virgl_renderer_resource_get_info() error check
hw/cxl: Standardize all references on CXL r3.1 and minor updates
hw/cxl: Update mailbox status registers.
hw/cxl: Update RAS Capability Definitions for version 3.
hw/cxl: Update link register definitions.
hw/cxl: Update HDM Decoder capability to version 3
tests/acpi: Update DSDT.cxl to reflect change _STA return value.
hw/i386: Fix _STA return value for ACPI0017
tests/acpi: Allow update of DSDT.cxl
hw/mem/cxl_type3: Fix potential divide by zero reported by coverity
hw/cxl: Pass NULL for a NULL MemoryRegionOps
hw/cxl: Pass CXLComponentState to cache_mem_ops
hw/cxl/device: read from register values in mdev_reg_read()
hw/cxl/mbox: Remove dead code
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU populates the apic_state attribute of x86 CPUs if supported by real
hardware or if SMP is active. When handling interrupts, it just checks whether
apic_state is populated to route the interrupt to the PIC or to the APIC.
However, chapter 10.4.3 of [1] requires that:
When IA32_APIC_BASE[11] is 0, the processor is functionally equivalent to an
IA-32 processor without an on-chip APIC.
This means that when apic_state is populated, QEMU needs to check for the
MSR_IA32_APICBASE_ENABLE flag in addition. Implement this which fixes some
real-world BIOSes.
[1] Intel 64 and IA-32 Architectures Software Developer's Manual, Vol. 3A:
System Programming Guide, Part 1
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240106132546.21248-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds support for x2APIC transitions when writing to
MSR_IA32_APICBASE register and finally adds CPUID_EXT_X2APIC to
TCG_EXT_FEATURES.
The set_base in APICCommonClass now returns an integer to indicate error in
execution. apic_set_base return -1 on invalid APIC state transition,
accelerator can use this to raise appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-4-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit extends the APIC ID to 32-bit long and remove the 255 max APIC
ID limit in userspace APIC. The array that manages local APICs is now
dynamically allocated based on the max APIC ID of created x86 machine.
Also, new x2APIC IPI destination determination scheme, self IPI and x2APIC
mode register access are supported.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-3-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit creates apic_register_read/write which are used by both
apic_mem_read/write for MMIO access and apic_msr_read/write for MSR access.
The apic_msr_read/write returns -1 on error, accelerator can use this to
raise the appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-2-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Include missing headers in order to avoid when refactoring
unrelated headers:
hw/intc/xics.c: In function 'icp_realize':
hw/intc/xics.c:304:5: error: unknown type name 'PowerPCCPU'
304 | PowerPCCPU *cpu;
| ^~~~~~~~~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
=+Pi0
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240111
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZZ/QKgAKCRBAov/yOSY+
# 34eqBADA48++Z9gETFNheLUHdYEaja2emn+gSaoHLFquyq/l53w8RfrUII+BzV1o
# T7D8xjlVQldAYZzqQn2pQe2S7r4ggfeNmxGxwJbCTW9sooGMwBnU8+Ix3ruSet7K
# gI+UHLU4oHk6jdrT384tux2EG+qUmlLN1c7j4G/z1OzKEwFv7Q==
# =+Pi0
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 11 Jan 2024 11:25:30 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240111' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_extioi: Add vmstate post_load support
hw/intc/loongarch_extioi: Add dynamic cpu number support
hw/loongarch/virt: Set iocsr address space per-board rather than percpu
hw/intc/loongarch_ipi: Use MemTxAttrs interface for ipi ops
target/loongarch: Add loongarch kvm into meson build
target/loongarch: Implement set vcpu intr for kvm
target/loongarch: Restrict TCG-specific code
target/loongarch: Implement kvm_arch_handle_exit
target/loongarch: Implement kvm_arch_init_vcpu
target/loongarch: Implement kvm_arch_init function
target/loongarch: Implement kvm get/set registers
target/loongarch: Supplement vcpu env initial when vcpu reset
target/loongarch: Define some kvm_arch interfaces
linux-headers: Synchronize linux headers from linux v6.7.0-rc8
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are elements sw_ipmap and sw_coremap, which is usd to speed
up irq injection flow. They are saved and restored in vmstate during
migration, indeed they can calculated from hw registers. Here
post_load is added for get sw_ipmap and sw_coremap from extioi hw
state.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-5-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
On LoongArch physical machine, one extioi interrupt controller only
supports 4 cpus. With processor more than 4 cpus, there are multiple
extioi interrupt controllers; if interrupts need to be routed to
other cpus, they are forwarded from extioi node0 to other extioi nodes.
On virt machine model, there is simple extioi interrupt device model.
All cpus can access register of extioi interrupt controller, however
interrupt can only be route to 4 vcpu for compatible with old kernel.
This patch adds dynamic cpu number support about extioi interrupt.
With old kernel legacy extioi model is used, however kernel can detect
and choose new route method in future, so that interrupt can be routed to
all vcpus.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-4-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
LoongArch system has iocsr address space, most iocsr registers are
per-board, however some iocsr register spaces banked for percpu such
as ipi mailbox and extioi interrupt status. For banked iocsr space,
each cpu has the same iocsr space, but separate data.
This patch changes iocsr address space per-board rather percpu,
for iocsr registers specified for cpu, MemTxAttrs.requester_id
can be parsed for the cpu. With this patches, the total address space
on board will be simple, only iocsr address space and system memory,
rather than the number of cpu and system memory.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
There are two interface pairs for MemoryRegionOps, read/write and
read_with_attrs/write_with_attrs. The later is better for ipi device
emulation since initial cpu can be parsed from attrs.requester_id.
And requester_id can be overrided for IOCSR_IPI_SEND and mail_send
function when it is to forward message to another vcpu.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Mark up the cpreginfo structs for the GIC CPU registers to indicate
the offsets from VNCR_EL2, as defined in table D8-66 in rule R_CSRPQ
in the Arm ARM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
The hypervisor can deliver (virtual) LPIs to a guest by setting up a
list register to have an intid which is an LPI. The GIC has to treat
these a little differently to standard interrupt IDs, because LPIs
have no Active state, and so the guest will only EOI them, it will
not also deactivate them. So icv_eoir_write() must do two things:
* if the LPI ID is not in any list register, we drop the
priority but do not increment the EOI count
* if the LPI ID is in a list register, we immediately deactivate
it, regardless of the split-drop-and-deactivate control
This can be seen in the VirtualWriteEOIR0() and VirtualWriteEOIR1()
pseudocode in the GICv3 architecture specification.
Without this fix, potentially a hypervisor guest might stall because
LPIs get stuck in a bogus Active+Pending state.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
Cortex-M NVIC can have a different number of priority bits.
Cortex-M0/M0+/M1 devices must use 2 or more bits, while devices based
on ARMv7m and up must use 3 or more bits.
This adds a "num-prio-bits" property which will get sensible default
values if unset (2 or 8 depending on the device). Unless a SOC
specifies the number of bits to use, the previous behavior is
maintained for backward compatibility.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240106181503.1746200-2-sam@rfc1149.net
Suggested-by: Anton Kochkov <anton.kochkov@proton.me>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1122
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Big QEMU Lock (BQL) has many names and they are confusing. The
actual QemuMutex variable is called qemu_global_mutex but it's commonly
referred to as the BQL in discussions and some code comments. The
locking APIs, however, are called qemu_mutex_lock_iothread() and
qemu_mutex_unlock_iothread().
The "iothread" name is historic and comes from when the main thread was
split into into KVM vcpu threads and the "iothread" (now called the main
loop thread). I have contributed to the confusion myself by introducing
a separate --object iothread, a separate concept unrelated to the BQL.
The "iothread" name is no longer appropriate for the BQL. Rename the
locking APIs to:
- void bql_lock(void)
- void bql_unlock(void)
- bool bql_locked(void)
There are more APIs with "iothread" in their names. Subsequent patches
will rename them. There are also comments and documentation that will be
updated in later patches.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Acked-by: Fabiano Rosas <farosas@suse.de>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Peter Xu <peterx@redhat.com>
Acked-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Acked-by: Hyman Huang <yong.huang@smartx.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20240102153529.486531-2-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The ICC_PMR_ELx and ICV_PMR_ELx bit masks returned from
ic{c,v}_fullprio_mask should technically also remove any
bit above 7 as these are marked reserved (read 0) and should
therefore should not be written as anything other than 0.
This was noted during a run of a proprietary test system and
discused on the mailing list [1] and initially thought not to
be an issue due to RES0 being technically allowed to be
written to and read back as long as the implementation does
not use the RES0 bits. It is very possible that the values
are used in comparison without masking, as pointed out by
Peter in [2], if (cs->hppi.prio >= cs->icc_pmr_el1) may well
do the wrong thing.
Masking these values in ic{c,v}_fullprio_mask() should fix
this and prevent any future problems with playing with the
values.
[1]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00607.html
[2]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00737.html
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Message-id: 20231116172818.792364-1-ben.dooks@codethink.co.uk
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hi
In this pull request:
- migration reboot mode (steve)
* I disabled the test because our CI don't like programs using so
much shared memory. Searching for a fix.
- test for postcopy recover (fabiano)
- MigrateAddress QAPI (het)
- better return path error handling (peter)
- traces for downtime (peter)
- vmstate_register() check for duplicates (juan)
thomas find better solutions for s390x and ipmi.
now also works on s390x
Please, apply.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmVDipMACgkQ9IfvGFhy
1yNYnQ/9E5Cywsoqljqa/9FiKBSII2qMrmkfu6JLKqePnsh5pFZiukbudYRuJCCe
ZTDEmD0NmKRJbDx2xRU1qx/e6gKJy+gz37KP89Buuh/WwZHPboPYtxQpGvCSiH26
J3i+1+TgaqmkLzcO35wa8tp6gneQclWeAwKgMvdb4cm2pJEhgWRKI62ccyLzxeve
UCzFQn60t55ETyVZGnRD4YwdTQvGKH+DPlyTuJOLR3DePuvZd8EdH+ypvB4RLAy7
3+CuQOxmF5LRXPbpJuAeOsudbmhhHzrO/yL7ZmsiKQTthsJv+SzC1bO94jhQrawZ
Q7GCii5KpGq0KnRTRKZRGk6XKwxcYRduXMX3R5tXuVmDmCZsjhXzziU8yEdftph8
5TJdk1o0Gb043EFu81mrsQYS+9yJqe6sy6m3PTJaec54cAty5ln+c17WOvpAOaSV
+1phe05ftuVPmQ3KWhbIR/tCmavNLwEZxpVIfyaKJx04bFbtQ9gRpRyURORX4KXc
s4WXvNirQEohxYBnP4TPvA09xBTW3V08pk/wRDwt0YDXnLiqCltOuxD8r05K8K4B
MkCLcWj0g7he2tBkF60oz1KSIE0oTB81um9AzLIv5F2YSYLaJM5BIcoC437MR2f4
MOR7drR1fP5GsRu/SeU5BWvhVq3IvdOxR7G2MLNRJJvl7ZtGXDc=
=uaqL
-----END PGP SIGNATURE-----
Merge tag 'migration-20231102-pull-request' of https://gitlab.com/juan.quintela/qemu into staging
Migration Pull request (20231102)
Hi
In this pull request:
- migration reboot mode (steve)
* I disabled the test because our CI don't like programs using so
much shared memory. Searching for a fix.
- test for postcopy recover (fabiano)
- MigrateAddress QAPI (het)
- better return path error handling (peter)
- traces for downtime (peter)
- vmstate_register() check for duplicates (juan)
thomas find better solutions for s390x and ipmi.
now also works on s390x
Please, apply.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEGJn/jt6/WMzuA0uC9IfvGFhy1yMFAmVDipMACgkQ9IfvGFhy
# 1yNYnQ/9E5Cywsoqljqa/9FiKBSII2qMrmkfu6JLKqePnsh5pFZiukbudYRuJCCe
# ZTDEmD0NmKRJbDx2xRU1qx/e6gKJy+gz37KP89Buuh/WwZHPboPYtxQpGvCSiH26
# J3i+1+TgaqmkLzcO35wa8tp6gneQclWeAwKgMvdb4cm2pJEhgWRKI62ccyLzxeve
# UCzFQn60t55ETyVZGnRD4YwdTQvGKH+DPlyTuJOLR3DePuvZd8EdH+ypvB4RLAy7
# 3+CuQOxmF5LRXPbpJuAeOsudbmhhHzrO/yL7ZmsiKQTthsJv+SzC1bO94jhQrawZ
# Q7GCii5KpGq0KnRTRKZRGk6XKwxcYRduXMX3R5tXuVmDmCZsjhXzziU8yEdftph8
# 5TJdk1o0Gb043EFu81mrsQYS+9yJqe6sy6m3PTJaec54cAty5ln+c17WOvpAOaSV
# +1phe05ftuVPmQ3KWhbIR/tCmavNLwEZxpVIfyaKJx04bFbtQ9gRpRyURORX4KXc
# s4WXvNirQEohxYBnP4TPvA09xBTW3V08pk/wRDwt0YDXnLiqCltOuxD8r05K8K4B
# MkCLcWj0g7he2tBkF60oz1KSIE0oTB81um9AzLIv5F2YSYLaJM5BIcoC437MR2f4
# MOR7drR1fP5GsRu/SeU5BWvhVq3IvdOxR7G2MLNRJJvl7ZtGXDc=
# =uaqL
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 02 Nov 2023 19:40:03 HKT
# gpg: using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg: aka "Juan Quintela <quintela@trasno.org>" [full]
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* tag 'migration-20231102-pull-request' of https://gitlab.com/juan.quintela/qemu: (40 commits)
migration: modify test_multifd_tcp_none() to use new QAPI syntax.
migration: Implement MigrateChannelList to hmp migration flow.
migration: Implement MigrateChannelList to qmp migration flow.
migration: modify migration_channels_and_uri_compatible() for new QAPI syntax
migration: New migrate and migrate-incoming argument 'channels'
migration: Convert the file backend to the new QAPI syntax
migration: convert exec backend to accept MigrateAddress.
migration: convert rdma backend to accept MigrateAddress
migration: convert socket backend to accept MigrateAddress
migration: convert migration 'uri' into 'MigrateAddress'
migration: New QAPI type 'MigrateAddress'
migration: Change ram_dirty_bitmap_reload() retval to bool
tests/migration-test: Add a test for postcopy hangs during RECOVER
migration: Allow network to fail even during recovery
migration: Refactor error handling in source return path
tests/qtest: migration: add reboot mode test
cpr: reboot mode
cpr: relax vhost migration blockers
cpr: relax blockdev migration blockers
migration: per-mode blockers
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Current code does:
- register pre_2_10_vmstate_dummy_icp with "icp/server" and instance
dependinfg on cpu number
- for newer machines, it register vmstate_icp with "icp/server" name
and instance 0
- now it unregisters "icp/server" for the 1st instance.
This is wrong at many levels:
- we shouldn't have two VMSTATEDescriptions with the same name
- In case this is the only solution that we can came with, it needs to
be:
* register pre_2_10_vmstate_dummy_icp
* unregister pre_2_10_vmstate_dummy_icp
* register real vmstate_icp
Created vmstate_replace_hack_for_ppc() with warnings left and right
that it is a hack.
CC: Cedric Le Goater <clg@kaod.org>
CC: Daniel Henrique Barboza <danielhb413@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Greg Kurz <groug@kaod.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231020090731.28701-8-quintela@redhat.com>
Avoid the interrupt controller directly access the 'first_cpu'
global. Pass 'cpu' from the board code.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231024083010.12453-2-philmd@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The feature test functions isar_feature_*() now take up nearly
a thousand lines in target/arm/cpu.h. This header file is included
by a lot of source files, most of which don't need these functions.
Move the feature test functions to their own header file.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231024163510.2972081-2-peter.maydell@linaro.org
KVM_IRQFD was introduced in Linux 2.6.32, and since then it has always been
available on architectures that support an in-kernel interrupt controller.
We can require it unconditionally.
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This was introduced in KVM in Linux 3.5, we can require it unconditionally
in kvm_irqchip_send_msi(). However, not all architectures have to implement
it so check it only in x86, the only architecture that ever had MSI injection
but not KVM_CAP_SIGNAL_MSI.
ARM uses it to detect the presence of the ITS emulation in the kernel,
introduced in Linux 4.8. Assume that it's there and possibly fail when
realizing the arm-its-kvm device.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify migrate_add_blocker and migrate_del_blocker to take an Error **
reason. This allows migration to own the Error object, so that if
an error occurs in migrate_add_blocker, migration code can free the Error
and clear the client handle, simplifying client code. It also simplifies
the migrate_del_blocker call site.
In addition, this is a pre-requisite for a proposed future patch that would
add a mode argument to migration requests to support live update, and
maintain a list of blockers for each mode. A blocker may apply to a single
mode or to multiple modes, and passing Error** will allow one Error object
to be registered for multiple modes.
No functional change.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Tested-by: Michael Galaxy <mgalaxy@akamai.com>
Reviewed-by: Michael Galaxy <mgalaxy@akamai.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <1697634216-84215-1-git-send-email-steven.sistare@oracle.com>
There is no point in exposing an internal MMIO region via
SysBus and directly mapping it in the very same device.
Just map it without using the SysBus API.
Transformation done using the following coccinelle script:
@@
expression sbdev;
expression index;
expression addr;
expression subregion;
@@
- sysbus_init_mmio(sbdev, subregion);
... when != sbdev
- sysbus_mmio_map(sbdev, index, addr);
+ memory_region_add_subregion(get_system_memory(), addr, subregion);
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-8-philmd@linaro.org>
In order to make the next commit trivial, move sysbus_init_mmio()
calls just before the corresponding sysbus_mmio_map() calls.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20231019131647.19690-7-philmd@linaro.org>
APICCommonClass::realize() is a DeviceRealize() handler which
take an Error** parameter and can fail. Do not proceed further
on failure.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20231003082728.83496-2-philmd@linaro.org>
Move the files to a 'kvm' dir to promote more code separation between
accelerators and making our lives easier supporting build options such
as --disable-tcg.
Rename kvm.c to kvm-cpu.c to keep it in line with its TCG counterpart.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230925175709.35696-13-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Avoid shadowing a local variable in do_process_its_cmd():
../../hw/intc/arm_gicv3_its.c:548:17: warning: declaration of ‘ite’ shadows a previous local [-Wshadow=compatible-local]
548 | ITEntry ite = {};
| ^~~
../../hw/intc/arm_gicv3_its.c:518:13: note: shadowed declaration is here
518 | ITEntry ite;
| ^~~
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20230922152944.3583438-2-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix:
hw/intc/openpic.c: In function ‘openpic_gbl_write’:
hw/intc/openpic.c:614:17: warning: declaration of ‘idx’ shadows a previous local [-Wshadow=compatible-local]
614 | int idx;
| ^~~
hw/intc/openpic.c:568:9: note: shadowed declaration is here
568 | int idx;
| ^~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230904162824.85385-3-philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
As reported by Coverity, "idx << xive->pc_shift" is evaluated using
32-bit arithmetic, and then used in a context expecting a "uint64_t".
Add a uint64_t cast.
Fixes: Coverity CID 1519049
Fixes: b68147b7a5 ("ppc/xive: Add support for the PC MMIOs")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-ID: <20230914154650.222111-1-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
* Remove 'host' CPU from TCG
* riscv_htif Fixup printing on big endian hosts
* Add zmmul isa string
* Add smepmp isa string
* Fix page_check_range use in fault-only-first
* Use existing lookup tables for MixColumns
* Add RISC-V vector cryptographic instruction set support
* Implement WARL behaviour for mcountinhibit/mcounteren
* Add Zihintntl extension ISA string to DTS
* Fix zfa fleq.d and fltq.d
* Fix upper/lower mtime write calculation
* Make rtc variable names consistent
* Use abi type for linux-user target_ucontext
* Add RISC-V KVM AIA Support
* Fix riscv,pmu DT node path in the virt machine
* Update CSR bits name for svadu extension
* Mark zicond non-experimental
* Fix satp_mode_finalize() when satp_mode.supported = 0
* Fix non-KVM --enable-debug build
* Add new extensions to hwprobe
* Use accelerated helper for AES64KS1I
* Allocate itrigger timers only once
* Respect mseccfg.RLB for pmpaddrX changes
* Align the AIA model to v1.0 ratified spec
* Don't read the CSR in riscv_csrrw_do64
-----BEGIN PGP SIGNATURE-----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=aqcx
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20230911' of https://github.com/alistair23/qemu into staging
First RISC-V PR for 8.2
* Remove 'host' CPU from TCG
* riscv_htif Fixup printing on big endian hosts
* Add zmmul isa string
* Add smepmp isa string
* Fix page_check_range use in fault-only-first
* Use existing lookup tables for MixColumns
* Add RISC-V vector cryptographic instruction set support
* Implement WARL behaviour for mcountinhibit/mcounteren
* Add Zihintntl extension ISA string to DTS
* Fix zfa fleq.d and fltq.d
* Fix upper/lower mtime write calculation
* Make rtc variable names consistent
* Use abi type for linux-user target_ucontext
* Add RISC-V KVM AIA Support
* Fix riscv,pmu DT node path in the virt machine
* Update CSR bits name for svadu extension
* Mark zicond non-experimental
* Fix satp_mode_finalize() when satp_mode.supported = 0
* Fix non-KVM --enable-debug build
* Add new extensions to hwprobe
* Use accelerated helper for AES64KS1I
* Allocate itrigger timers only once
* Respect mseccfg.RLB for pmpaddrX changes
* Align the AIA model to v1.0 ratified spec
* Don't read the CSR in riscv_csrrw_do64
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmT+ttMACgkQr3yVEwxT
# gBN/rg/+KhOvL9xWSNb8pzlIsMQHLvndno0Sq5b9Rb/o5z1ekyYfyg6712N3JJpA
# TIfZzOIW7oYZV8gHyaBtOt8kIbrjwzGB2rpCh4blhm+yNZv7Ym9Ko6AVVzoUDo7k
# 2dWkLnC+52/l3SXGeyYMJOlgUUsQMwjD6ykDEr42P6DfVord34fpTH7ftwSasO9K
# 35qJQqhUCgB3fMzjKTYICN6Rm1UluijTjRNXUZXC0XZlr+UKw2jT/UsybbWVXyNs
# SmkRtF1MEVGvw+b8XOgA/nG1qVCWglTMcPvKjWMY+cY9WLM6/R9nXAV8OL/JPead
# v1LvROJNukfjNtDW6AOl5/svOJTRLbIrV5EO7Hlm1E4kftGmE5C+AKZZ/VT4ucUK
# XgqaHoXh26tFEymVjzbtyFnUHNv0zLuGelTnmc5Ps1byLSe4lT0dBaJy6Zizg0LE
# DpTR7s3LpyV3qB96Xf9bOMaTPsekUjD3dQI/3X634r36+YovRXapJDEDacN9whbU
# BSZc20NoM5UxVXFTbELQXolue/X2BRLxpzB+BDG8/cpu/MPgcCNiOZaVrr/pOo33
# 6rwwrBhLSCfYAXnJ52qTUEBz0Z/FnRPza8AU/uuRYRFk6JhUXIonmO6xkzsoNKuN
# QNnih/v1J+1XqUyyT2InOoAiTotzHiWgKZKaMfAhomt2j/slz+A=
# =aqcx
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 11 Sep 2023 02:42:27 EDT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20230911' of https://github.com/alistair23/qemu: (45 commits)
target/riscv: don't read CSR in riscv_csrrw_do64
target/riscv: Align the AIA model to v1.0 ratified spec
target/riscv/pmp.c: respect mseccfg.RLB for pmpaddrX changes
target/riscv: Allocate itrigger timers only once
target/riscv: Use accelerated helper for AES64KS1I
linux-user/riscv: Add new extensions to hwprobe
hw/intc/riscv_aplic.c fix non-KVM --enable-debug build
hw/riscv/virt.c: fix non-KVM --enable-debug build
riscv: zicond: make non-experimental
target/riscv: fix satp_mode_finalize() when satp_mode.supported = 0
target/riscv: Update CSR bits name for svadu extension
hw/riscv: virt: Fix riscv,pmu DT node path
target/riscv: select KVM AIA in riscv virt machine
target/riscv: update APLIC and IMSIC to support KVM AIA
target/riscv: Create an KVM AIA irqchip
target/riscv: check the in-kernel irqchip support
target/riscv: support the AIA device emulation with KVM enabled
linux-user/riscv: Use abi type for target_ucontext
hw/intc: Make rtc variable names consistent
hw/intc: Fix upper/lower mtime write calculation
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 6df0b37e2ab breaks a --enable-debug build in a non-KVM
environment with the following error:
/usr/bin/ld: libqemu-riscv64-softmmu.fa.p/hw_intc_riscv_aplic.c.o: in function `riscv_kvm_aplic_request':
./qemu/build/../hw/intc/riscv_aplic.c:486: undefined reference to `kvm_set_irq'
collect2: error: ld returned 1 exit status
This happens because the debug build will poke into the
'if (is_kvm_aia(aplic->msimode))' block and fail to find a reference to
the KVM only function riscv_kvm_aplic_request().
There are multiple solutions to fix this. We'll go with the same
solution from the previous patch, i.e. add a kvm_enabled() conditional
to filter out the block. But there's a catch: riscv_kvm_aplic_request()
is a local function that would end up being used if the compiler crops
the block, and this won't work. Quoting Richard Henderson's explanation
in [1]:
"(...) the compiler won't eliminate entire unused functions with -O0"
We'll solve it by moving riscv_kvm_aplic_request() to kvm.c and add its
declaration in kvm_riscv.h, where all other KVM specific public
functions are already declared. Other archs handles KVM specific code in
this manner and we expect to do the same from now on.
[1] https://lore.kernel.org/qemu-riscv/d2f1ad02-eb03-138f-9d08-db676deeed05@linaro.org/
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230830133503.711138-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
KVM AIA can't emulate APLIC only. When "aia=aplic" parameter is passed,
APLIC devices is emulated by QEMU. For "aia=aplic-imsic", remove the
mmio operations of APLIC when using KVM AIA and send wired interrupt
signal via KVM_IRQ_LINE API.
After KVM AIA enabled, MSI messages are delivered by KVM_SIGNAL_MSI API
when the IMSICs receive mmio write requests.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20230727102439.22554-5-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The variables whose values are given by cpu_riscv_read_rtc() should be named
"rtc". The variables whose value are given by cpu_riscv_read_rtc_raw()
should be named "rtc_r".
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230728082502.26439-2-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When writing the upper mtime, we should keep the original lower mtime
whose value is given by cpu_riscv_read_rtc() instead of
cpu_riscv_read_rtc_raw(). The same logic applies to writes to lower mtime.
Signed-off-by: Jason Chien <jason.chien@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20230728082502.26439-1-jason.chien@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix when using GCC v11.4 (Ubuntu 11.4.0-1ubuntu1~22.04) with CFLAGS=-Og:
[4/6] Compiling C object libcommon.fa.p/hw_intc_arm_gicv3_its.c.o
FAILED: libcommon.fa.p/hw_intc_arm_gicv3_its.c.o
inlined from ‘lookup_vte’ at hw/intc/arm_gicv3_its.c:453:9,
inlined from ‘vmovp_callback’ at hw/intc/arm_gicv3_its.c:1039:14:
hw/intc/arm_gicv3_its.c:347:9: error: ‘vte.rdbase’ may be used uninitialized [-Werror=maybe-uninitialized]
347 | trace_gicv3_its_vte_read(vpeid, vte->valid, vte->vptsize,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
348 | vte->vptaddr, vte->rdbase);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_its.c: In function ‘vmovp_callback’:
hw/intc/arm_gicv3_its.c:1036:13: note: ‘vte’ declared here
1036 | VTEntry vte;
| ^~~
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230831131348.69032-1-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XIVE interrupt contoller maintains various fields on interrupt
targets in a structure called NVT. Each unit has a NVT cache, backed
by RAM.
When the NVT structure is not local (in RAM) to the chip, the XIVE
interrupt controller forwards the memory operation to the owning chip
using the PC MMIO region configured for this purpose. QEMU does not
need to be so precise since software shouldn't perform any of these
operations. The model implementation is simplified to return the RAM
address of the NVT structure which is then used by pnv_xive_vst_write
or read to perform the operation in RAM.
Remove the last use of pnv_xive_get_remote().
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The notify page of the interrupt controller can either be used to
receive trigger events from the HW controllers (PHB, PSI) or to
reroute interrupts between Interrupt Controllers. In which case, the
VSD table is used to determine the address of the notify page of the
remote IC and the store data is forwarded.
Today, our model grabs the remote VSD (EAS, END, NVT) address using
pnv_xive_get_remote() helper. Be more precise and implement remote END
triggers using a store on the remote IC notify page.
We still have a shortcut in the model for the NVT accesses which we
will address later.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will help us model the END triggers on the PowerNV machine, which
can be rerouted to another interrupt controller.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
to log an error in case of bad configuration of the XIVE tables by the FW.
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
HAX is deprecated since commits 73741fda6c ("MAINTAINERS: Abort
HAXM maintenance") and 90c167a1da ("docs/about/deprecated: Mark
HAXM in QEMU as deprecated"), released in v8.0.0.
Per the latest HAXM release (v7.8 [*]), the latest QEMU supported
is v7.2:
Note: Up to this release, HAXM supports QEMU from 2.9.0 to 7.2.0.
The next commit (https://github.com/intel/haxm/commit/da1b8ec072)
added:
HAXM v7.8.0 is our last release and we will not accept
pull requests or respond to issues after this.
It became very hard to build and test HAXM. Its previous
maintainers made it clear they won't help. It doesn't seem to be
a very good use of QEMU maintainers to spend their time in a dead
project. Save our time by removing this orphan zombie code.
[*] https://github.com/intel/haxm/releases/tag/v7.8.0
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230831082016.60885-1-philmd@linaro.org>
For edge triggered irq, qemu_irq_pulse is used to inject irq. It will
set irq with high level and low level soon to simluate pulse irq.
For edge triggered irq, irq is injected and set as pending at rising
level, do not clear irq at lowering level. LoongArch pch interrupt will
clear irq for lowering level irq, there will be problem. ACPI ged deivce
is edge-triggered irq, it is used for cpu/memory hotplug.
This patch fixes memory hotplug issue on LoongArch virt machine.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230707091557.1474790-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
If QEMU is built with --without-default-devices, the s390-flic-kvm
device is missing and QEMU aborts when started with the KVM accelerator.
Make sure it's available by selecting S390_FLIC_KVM in Kconfig.
Consequently, this also fixes an abort in tests/qtest/migration-test.
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20230711151440.716822-1-clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The low-level functions to access the TIMA take a presenter object as
a first argument. When accessing the TIMA from the IC BAR,
i.e. indirect calls, we currently pass a NULL pointer for the
presenter argument. While it appears ok with the current usage, it's
dangerous. And it's pretty easy to figure out the presenter in that
context, so this patch fixes it.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230705081400.218408-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add the CPU target in the trace when reading/writing the TIMA
space. It was already done for other TIMA ops (notify, accept, ...),
only missing for those 2. Useful for debug and even more now that we
experiment with SMT.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230705110039.231148-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
We currently only allow 64-bit operations on the ESB CI pages. There's
no real reason for that limitation, skiboot/linux didn't need
more. However the hardware supports any size, so this patch relaxes
that restriction. It impacts both the ESB pages for "normal"
interrupts as well as the ESB pages for escalation interrupts defined
for the ENDs.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230704144848.164287-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The PQ state of a xive interrupt is always initialized to Q=1, which
means the interrupt is disabled. Since a xive source can be embedded
in many objects, this patch adds a property to allow that behavior to
be refined if needed.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230703081215.55252-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Direct TIMA operations can be done through 4 pages, each with a
different privilege level dictating what fields can be accessed. On
the other hand, indirect TIMA accesses on P10 are done through a
single page, which is the equivalent of the most privileged page of
direct TIMA accesses.
The offset in the IC bar of an indirect access specifies what hw
thread is targeted (page shift bits) and the offset in the
TIMA being accessed (the page offset bits). When the indirect
access is calling the underlying direct access functions, it is
therefore important to clearly separate the 2, as the direct functions
assume any page shift bits define the privilege ring level. For
indirect accesses, those bits must be 0. This patch fixes the offset
passed to direct TIMA functions.
It didn't matter for SMT1, as the 2 least significant bits of the page
shift are part of the hw thread ID and always 0, so the direct TIMA
functions were accessing the privilege ring 0 page. With SMT4/8, it is
no longer true.
The fix is specific to P10, as indirect TIMA access on P9 was handled
differently.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230703080858.54060-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Booting linux on the powernv10 machine logs a few errors like:
Invalid read at addr 0x38, size 1, region 'xive-ic-tm-indirect', reason: invalid size (min:8 max:8)
Invalid write at addr 0x38, size 1, region 'xive-ic-tm-indirect', reason: invalid size (min:8 max:8)
Invalid read at addr 0x38, size 1, region 'xive-ic-tm-indirect', reason: invalid size (min:8 max:8)
Those errors happen when linux is resetting XIVE. We're trying to
read/write the enablement bit for the hardware context and qemu
doesn't allow indirect TIMA accesses of less than 8 bytes. Direct TIMA
access can go through though, as well as indirect TIMA accesses on P9.
So even though there are some restrictions regarding the address/size
combinations for TIMA access, the example above is perfectly valid.
This patch lets indirect TIMA accesses of all sizes go through. The
special operations will be intercepted and the default "raw" handlers
will pick up all other requests and complain about invalid sizes as
appropriate.
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230626094057.1192473-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
"hw/core/cpu.h" defines 'first_cpu' as QTAILQ_FIRST_RCU(&cpus).
arm_gic_common_reset_irq_state() calls its second argument
'first_cpu', producing a build failure when "hw/core/cpu.h"
is included:
hw/intc/arm_gic_common.c:238:68: warning: omitting the parameter name in a function definition is a C2x extension [-Wc2x-extensions]
static inline void arm_gic_common_reset_irq_state(GICState *s, int first_cpu,
^
include/hw/core/cpu.h:451:26: note: expanded from macro 'first_cpu'
#define first_cpu QTAILQ_FIRST_RCU(&cpus)
^
KISS, rename the function argument.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230405160454.97436-5-philmd@linaro.org>
"kvm_arm.h" contains external and internal prototype declarations.
Files under the hw/ directory should only access the KVM external
API.
In order to avoid machine / device models to include "kvm_arm.h"
simply to get the QOM GIC/ITS class name, un-inline each class
name getter to the proper device model file.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230405160454.97436-4-philmd@linaro.org>
Accessing the TIMA from some specific ring/offset combination can
trigger a special operation, with or without side effects. It is
implemented in qemu with an array of special operations to compare
accesses against. Since the presenter on P10 is pretty similar to P9,
we had the full array defined for P9 and we just had a special case
for P10 to treat one access differently. With a recent change,
6f2cbd133d ("pnv/xive2: Handle TIMA access through all ports"), we
now ignore some of the bits of the TIMA address, but that patch
managed to botch the detection of the special case for P10.
To clean that up, this patch introduces a full array of special ops to
be used for P10. The code to detect a special access is common with
P9, only the array of operations differs. The presenter can pick the
correct array of special ops based on its configuration introduced in
a previous patch.
Fixes: Coverity CID 1512997, 1512998
Fixes: 6f2cbd133d ("pnv/xive2: Handle TIMA access through all ports")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The presenters for xive on P9 and P10 are mostly similar but the
behavior can be tuned through a few CQ registers. This patch adds a
"get_config" method, which will allow to access that config from the
presenter in a later patch.
For now, just define the config for the TIMA version.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In commit 2c5fa0778c we fixed an endianness bug in the Allwinner
A10 PIC model; however in the process we introduced a regression.
This is because the old code was robust against the incoming 'level'
argument being something other than 0 or 1, whereas the new code was
not.
In particular, the allwinner-sdhost code treats its IRQ line
as 0-vs-non-0 rather than 0-vs-1, so when the SD controller
set its IRQ line for any reason other than transmit the
interrupt controller would ignore it. The observed effect
was a guest timeout when rebooting the guest kernel.
Handle level values other than 0 or 1, to restore the old
behaviour.
Fixes: 2c5fa0778c ("hw/intc/allwinner-a10-pic: Don't use set_bit()/clear_bit()")
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20230606104609.3692557-2-peter.maydell@linaro.org
LoongArch ipi device uses physical cpuid to route to different
vcpus rather logical cpuid, and the physical cpuid is the same
with cpuid in acpi dsdt and srat table.
Reviewed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230613120552.2471420-3-zhaotianrui@loongson.cn>
According to the `The RISC-V Advanced Interrupt Architecture`
document, if register `mmsiaddrcfgh` of the domain has bit L set
to one, then `smsiaddrcfg` and `smsiaddrcfgh` are locked as
read-only alongside `mmsiaddrcfg` and `mmsiaddrcfgh`.
Signed-off-by: Tommy Wu <tommy.wu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <20230609055936.3925438-1-tommy.wu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When dumping the END and NVP tables ("info pic" from the HMP) on the
P10 model, we're likely to be flooded with error messages such as:
XIVE[0] - VST: invalid NVPT entry f33800 !?
The error is printed when finding an empty VSD in an indirect
table (thus END and NVP tables with skiboot), which is going to happen
when dumping the xive state. So let's tune down those messages. They
can be re-enabled easily with a macro if needed.
Those errors were already hidden on xive/P9, for the same reason.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230531150537.369350-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Thread Interrupt Management Area (TIMA) can be accessed through 4
ports, targeted by the address. The base address of a TIMA
is using port 0 and the other ports are 0x80 apart. Using one port or
another can be useful to balance the load on the snoop buses. With
skiboot and linux, we currently use port 0, but as it tends to be
busy, another hypervisor is using port 1 for TIMA access.
The port address bits fall in between the special op indication
bits (the 2 MSBs) and the register offset bits (the 6 LSBs). They are
"don't care" for the hardware when processing a TIMA operation. This
patch filters out those port address bits so that a TIMA operation can
be triggered using any port.
It is also true for indirect access (through the IC BAR) and it's
actually nothing new, it was already the case on P9. Which helps here,
as the TIMA handling code is common between P9 (xive) and P10 (xive2).
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-6-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
TIMA addresses are somewhat special and are split in several bit
fields with different meanings. This patch describes it and introduce
macros to more easily access the various fields.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-5-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Fix what was probably a silly mistake and allow to write the Physical
Thread enable registers 0 and 1. Skiboot prefers to use the ENx_SET
variant so it went unnoticed, but there's no reason to discard a write
to the full register, it is Read-Write.
Fixes: da71b7e3ed ("ppc/pnv: Add a XIVE2 controller to the POWER10 chip")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-4-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add basic read/write support for the ESB cache configuration register
on P10. We don't model the ESB cache in qemu so reading/writing the
register won't do anything, but it avoids logging a guest error when
skiboot configures it:
qemu-system-ppc64 -machine powernv10 ... -d guest_errors
...
XIVE[0] - VC: invalid read @240
XIVE[0] - VC: invalid write @240
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add basic read/write support for the TCTXT Config register on P10. qemu
doesn't do anything with it yet, but it avoids logging a guest error
when skiboot configures the fused-core state:
qemu-system-ppc64 -machine powernv10 ... -d guest_errors
...
[ 0.131670000,5] XIVE: [ IC 00 ] Initializing XIVE block ID 0...
XIVE[0] - TCTXT: invalid read @140
XIVE[0] - TCTXT: invalid write @140
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
As per "Loongson 3A5000/3B5000 Processor Reference Manual",
Loongson 3A5000's IPI implementation have 4 mailboxes per
core.
However, in 78464f023b ("hw/loongarch/virt: Modify ipi as
percpu device"), the number of IPI mailboxes was reduced to
one, which mismatches actual hardware.
It won't affect LoongArch based system as LoongArch boot code
only uses the first mailbox, however MIPS based Loongson boot
code uses all 4 mailboxes.
Fixes Coverity CID: 1512452, 1512453
Fixes: 78464f023b ("hw/loongarch/virt: Modify ipi as percpu device")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230521102307.87081-2-jiaxun.yang@flygoat.com>
Signed-off-by: Song Gao <gaosong@loongson.cn>
When ipi mailbox is used, cpu_index is decoded from iocsr register.
cpu maybe does not exist. This patch adds NULL pointer check on
ipi device.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230512100421.1867848-4-gaosong@loongson.cn>
Add separate macro EXTIOI_CPUS for extioi interrupt controller, extioi
only supports 4 cpu. And set macro LOONGARCH_MAX_CPUS as 256 so that
loongarch virt machine supports more cpus.
Interrupts from external devices can only be routed cpu 0-3 because
of extioi limits, cpu internal interrupt such as timer/ipi can be
triggered on all cpus.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230512100421.1867848-3-gaosong@loongson.cn>
ipi is used to communicate between cpus, this patch modified
loongarch ipi device as percpu device, so that there are
2 MemoryRegions with ipi device, rather than 2*cpus
MemoryRegions, which may be large than QDEV_MAX_MMIO if
more cpus are added on loongarch virt machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230512100421.1867848-2-gaosong@loongson.cn>
loongarch_ipi_iocsr MRs rely on re-entrant IO through the ipi_send
function. As such, mark these MRs re-entrancy-safe.
Fixes: a2e1753b80 ("memory: prevent dma-reentracy issues")
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230506112145.3563708-1-alxndr@bu.edu>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The calling function is already working with hwaddr and uint64_t so
lets avoid bringing target_ulong in if we don't need to.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230404132711.2563638-1-alex.bennee@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Since g_new is used to initialize the RISCVAPLICState->state structure,
in some case we get behavior that is not as expected. This patch
changes this to g_new0, which allows to initialize the APLIC in the correct state.
Signed-off-by: Ivan Klokov <ivan.klokov@syntacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <20230413133432.53771-1-ivan.klokov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Allwinner PIC model uses set_bit() and clear_bit() to update the
values in its irq_pending[] array when an interrupt arrives. However
it is using these functions wrongly: they work on an array of type
'long', and it is passing an array of type 'uint32_t'. Because the
code manually figures out the right array element, this works on
little-endian hosts and on 32-bit big-endian hosts, where bits 0..31
in a 'long' are in the same place as they are in a 'uint32_t'.
However it breaks on 64-bit big-endian hosts.
Remove the use of set_bit() and clear_bit() in favour of using
deposit32() on the array element. This fixes a bug where on
big-endian 64-bit hosts the guest kernel would hang early on in
bootup.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230424152833.1334136-1-peter.maydell@linaro.org
As the code is designed for re-entrant calls to apic-msi, mark apic-msi
as reentrancy-safe.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20230427211013.2994127-9-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This had been pulled in via qemu/plugin.h from hw/core/cpu.h,
but that will be removed.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230310195252.210956-5-richard.henderson@linaro.org>
[AJB: add various additional cases shown by CI]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230315174331.2959-15-alex.bennee@linaro.org>
Reviewed-by: Emilio Cota <cota@braap.org>
A Linux guest will perform IRQ migration after the IRQ has happened,
updating the RTE to point to the new destination CPU and then unmasking
the interrupt.
However, when the guest updates the RTE, ioapic_mem_write() calls
ioapic_service(), which redelivers the pending level interrupt via
kvm_set_irq(), *before* calling ioapic_update_kvm_routes() which sets
the new target CPU.
Thus, the IRQ which is supposed to go to the new target CPU is instead
misdelivered to the previous target. An example where the guest kernel
is attempting to migrate from CPU#2 to CPU#0 shows:
xenstore_read tx 0 path control/platform-feature-xs_reset_watches
ioapic_set_irq vector: 11 level: 1
ioapic_set_remote_irr set remote irr for pin 11
ioapic_service: trigger KVM IRQ 11
[ 0.523627] The affinity mask was 0-3 and the handler is on 2
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x27 size 0x4 val 0x26
ioapic_update_kvm_routes: update KVM route for IRQ 11: fee02000 8021
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x18021
xenstore_reset_watches
ioapic_set_irq vector: 11 level: 1
ioapic_mem_read ioapic mem read addr 0x10 regsel: 0x26 size 0x4 retval 0x1c021
[ 0.524569] ioapic_ack_level IRQ 11 moveit = 1
ioapic_eoi_broadcast EOI broadcast for vector 33
ioapic_clear_remote_irr clear remote irr for pin 11 vector 33
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x26
ioapic_mem_read ioapic mem read addr 0x10 regsel: 0x26 size 0x4 retval 0x18021
[ 0.525235] ioapic_finish_move IRQ 11 calls irq_move_masked_irq()
[ 0.526147] irq_do_set_affinity for IRQ 11, 0
[ 0.526732] ioapic_set_affinity for IRQ 11, 0
[ 0.527330] ioapic_setup_msg_from_msi for IRQ11 target 0
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x27
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x27 size 0x4 val 0x0
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x27 size 0x4 val 0x26
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x18021
[ 0.527623] ioapic_set_affinity returns 0
[ 0.527623] ioapic_finish_move IRQ 11 calls unmask_ioapic_irq()
ioapic_mem_write ioapic mem write addr 0x0 regsel: 0x26 size 0x4 val 0x26
ioapic_mem_write ioapic mem write addr 0x10 regsel: 0x26 size 0x4 val 0x8021
ioapic_set_remote_irr set remote irr for pin 11
ioapic_service: trigger KVM IRQ 11
ioapic_update_kvm_routes: update KVM route for IRQ 11: fee00000 8021
[ 0.529571] The affinity mask was 0 and the handler is on 2
[ xenstore_watch path memory/target token FFFFFFFF92847D40
There are no other code paths in ioapic_mem_write() which need the KVM
IRQ routing table to be updated, so just shift the call from the end
of the function to happen right before the call to ioapic_service()
and thus deliver the re-enabled IRQ to the right place.
Alternative fixes might have been just to remove the part in
ioapic_service() which delivers the IRQ via kvm_set_irq() because
surely delivering as MSI ought to work just fine anyway in all cases?
That code lacks a comment justifying its existence.
Or maybe in the specific case shown in the above log, it would have
sufficed for ioapic_update_kvm_routes() to update the route *even*
when the IRQ is masked. It's not like it's actually going to get
triggered unless QEMU deliberately does so, anyway? But that only
works because the target CPU happens to be in the high word of the
RTE; if something in the *low* word (vector, perhaps) was changed
at the same time as the unmask, we'd still trigger with stale data.
Fixes: 15eafc2e60 "kvm: x86: add support for KVM_CAP_SPLIT_IRQCHIP"
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20230308111952.2728440-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Back in the mists of time, before EISA came along and required per-pin
level control in the ELCR register, the i8259 had a single chip-wide
level-mode control in bit 3 of ICW1.
Even in the PIIX3 datasheet from 1996 this is documented as 'This bit is
disabled', but apparently MorphOS is using it in the version of the
i8259 which is in the Pegasos2 board as part of the VT8231 chipset.
It's easy enough to implement, and I think it's harmless enough to do so
unconditionally.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[balaton: updated commit message as asked by author]
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <3f09b2dd109d19851d786047ad5c2ff459c90cd7.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Some length properties are signed, other unsigned:
hw/mips/cps.c:183: DEFINE_PROP_UINT32("num-vp", MIPSCPSState, num_vp, 1),
hw/mips/cps.c:184: DEFINE_PROP_UINT32("num-irq", MIPSCPSState, num_irq, 256),
hw/misc/mips_cmgcr.c:215: DEFINE_PROP_INT32("num-vp", MIPSGCRState, num_vps, 1),
hw/misc/mips_cpc.c:167: DEFINE_PROP_UINT32("num-vp", MIPSCPCState, num_vp, 0x1),
hw/misc/mips_itu.c:552: DEFINE_PROP_INT32("num-fifo", MIPSITUState, num_fifo,
hw/misc/mips_itu.c:554: DEFINE_PROP_INT32("num-semaphores", MIPSITUState,
Since negative values are not used (the minimum is '0'),
unify by declaring all properties as unsigned.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230203113650.78146-9-philmd@linaro.org>
Qemu_get_cpu uses the logical CPU id assigned during init to fetch the
CPU state. However APLIC, IMSIC and ACLINT contain registers and states
which are specific to physical hart Ids. The hart Ids in any given system
might be sparse and hence calls to qemu_get_cpu need to be replaced by
cpu_by_arch_id which performs lookup based on the sparse physical hart IDs.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230303065055.915652-3-mchitale@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
i8259_init() helper creates a i8259 device on an ISA bus,
connects its IRQ output to the parent's input IRQ, and
returns an array of 16 ISA input IRQs.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210163744.32182-2-philmd@linaro.org>
The ioapic sources reside in hw/intc already. Move the headers there
as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-11-shentey@gmail.com>
[PMD: Keep ioapic_internal.h in hw/intc/, not under include/]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This is in preparation to moving the hflags code into its own file
under the tcg/ directory.
Signed-off-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no point in using a void pointer to access the NVIC.
Use the real type to avoid casting it while debugging.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230206223502.25122-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mark up the sysreg definitions for the registers trapped
by HFGRTR/HFGWTR bits 36..63.
Of these, some correspond to RAS registers which we implement as
always-UNDEF: these don't need any extra handling for FGT because the
UNDEF-to-EL1 always takes priority over any theoretical
FGT-trap-to-EL2.
Bit 50 (NACCDATA_EL1) is for the ACCDATA_EL1 register which is part
of the FEAT_LS64_ACCDATA feature which we don't yet implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Fuad Tabba <tabba@google.com>
Message-id: 20230130182459.3309057-14-peter.maydell@linaro.org
Message-id: 20230127175507.2895013-14-peter.maydell@linaro.org
We currently only support GICv2 emulation. To also support GICv3, we will
need to pass a few system registers into their respective handler functions.
This patch adds support for HVF to call into the TCG callbacks for GICv3
system register handlers. This is safe because the GICv3 TCG code is generic
as long as we limit ourselves to EL0 and EL1 - which are the only modes
supported by HVF.
To make sure nobody trips over that, we also annotate callbacks that don't
work in HVF mode, such as EL state change hooks.
With GICv3 support in place, we can run with more than 8 vCPUs.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20230128224459.70676-1-agraf@csgraf.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip are defined
in pnv.h. Many users of the header don't actually need them. One
instance is this inclusion loop: hw/ppc/pnv_homer.h includes
hw/ppc/pnv.h for typedef PnvChip, and vice versa for struct PnvHomer.
Similar structs live in their own headers: PnvHomerClass and PnvHomer
in pnv_homer.h, PnvLpcClass and PnvLpcController in pci_lpc.h,
PnvPsiClass, PnvPsi, Pnv8Psi, Pnv9Psi, Pnv10Psi in pnv_psi.h, ...
Move PnvChipClass, PnvChip, Pnv8Chip, Pnv9Chip, and Pnv10Chip to new
pnv_chip.h, and adjust include directives. This breaks the inclusion
loop mentioned above.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221222104628.659681-2-armbru@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Seems like there is also nothing target-specific in here, so these
files can be moved to softmmu_ss to avoid that they get compiled
twice (once for qemu-system-arm and once for qemu-system-aarch64).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112134928.1026006-7-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Goldfish interrupt controller is not target specific.
While the Exynos interrupt combiner is only used by the ARM
targets, we can build this device once for all.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221209170042.71169-3-philmd@linaro.org>
[thuth: Change patch title, and also move 'exynos4210_gic.c']
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230112134928.1026006-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
A bunch of cleanups from various people.
- Improved GT64120 on big-endian hosts
- GT64120 north bridge and MC146818 RTC devices are now target independent
- Bonito64 north bridge converted to 3-phase reset API
- PCI refactors around PIIX devices
- Support for nanoMIPS in bootloader generator API
- New YAMON Malta Avocado test
- Removal of 'trap and emulate' KVM support
- System-specific QMP commands restricted to system emulation
-----BEGIN PGP SIGNATURE-----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=oXX+
-----END PGP SIGNATURE-----
Merge tag 'mips-20230113' of https://github.com/philmd/qemu into staging
MIPS patches queue
A bunch of cleanups from various people.
- Improved GT64120 on big-endian hosts
- GT64120 north bridge and MC146818 RTC devices are now target independent
- Bonito64 north bridge converted to 3-phase reset API
- PCI refactors around PIIX devices
- Support for nanoMIPS in bootloader generator API
- New YAMON Malta Avocado test
- Removal of 'trap and emulate' KVM support
- System-specific QMP commands restricted to system emulation
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmPBekAACgkQ4+MsLN6t
# wN4wjxAAtYxyt6WUBpiYfV/LnbQFpAsacues1Vhy9MPYEg5a/iuXWKvWtgRYvGww
# qR0GVQH8rH7tgnCZK+ioq9jX+hvfBskP6CnKhxmb5zDGm7vP7jhhu8UFWY/EtBgq
# 0zpNeLMXtnRJ6PBqo/nWFCVtcpDRZ6IkSbpGWkVkciRFc5n/2VCnlIj8k2I1oMvL
# 11cp2xFQnaPReFXIpMjJHuHv1NObykdlvVg6wQo/A/4qIb8EvJQEPmePjG9Sf0i0
# v2dhnnxG9mze7+uq0dIC16x8Azko3N7dmtNlBU/aGb9OELwx35aux2M4dNDVogwn
# DqL/Wsk54TFewECOfS48t/a/TqV8j/ISW1d/JvovBrN2KovmIAbtqHuMUqKVk5l0
# 23ZOIIPIYwmScZwIlkCIGUuIzFig1zhEmQcoEQaFe/B0oLB2eN/x0Bk9Yklo+i2A
# WNiyiAj7k5492qEdndOySEEDVt6886F/+CdQ6QYF5Z1L/ELck7XHBH3mGDznWpPn
# 6IURyVquPJx7ul62jSGI+Gc+qakNoahIhPo5O7hklOM9GwWNOWXHveyb7xjs7j+O
# eWyVcet+o7hoHkCzmfbyTPySI4qCpF9fA42jqPhATwQPwmGXpbr+4BxUq3KtE43y
# w9tEigwd4voN3dWLItVh6QE4in70osz3XHp93byvo8bHlS0huVY=
# =oXX+
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 13 Jan 2023 15:35:28 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'mips-20230113' of https://github.com/philmd/qemu: (46 commits)
scripts/git.orderfile: Display MAINTAINERS changes first
target/mips: Restrict 'qapi-commands-machine.h' to system emulation
hw/mips/boston: Rename MachineState 'mc' pointer to 'ms'
hw/pci-host/bonito: Declare TYPE_BONITO_PCI_HOST_BRIDGE in header
hw/pci-host/bonito: Use 'bonito_pci' for PCI function #0 code
hw/pci-host/bonito: Use 'bonito_host' for PCI host bridge code
hw/pci-host/bonito: Convert to 3-phase reset
softmmu/rtc: Emit warning when using driftfix=slew on systems without mc146818
hw/rtc/mc146818rtc: Make the mc146818 RTC device target independent
hw/core/qdev-properties-system: Allow the 'slew' policy only on x86
hw/intc: Extract the IRQ counting functions into a separate file
hw/intc/i8259: Make using the isa_pic singleton more type-safe
hw/usb/hcd-uhci: Introduce TYPE_ defines for device models
hw/mips/Kconfig: Track Malta's PIIX dependencies via Kconfig
hw/isa/piix4: Decouple INTx-to-LNKx routing which is board-specific
hw/isa/piix3: Decouple INTx-to-LNKx routing which is board-specific
hw/pci/pci: Factor out pci_bus_map_irqs() from pci_bus_irqs()
hw/pci/pci_host: Trace config accesses on unexisting functions
mips: Always include nanomips disassembler
mips: Remove support for trap and emulate KVM
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These IRQ counting functions will soon be required in binaries that
do not include the APIC code, too, so let's extract them into a
separate file that can be linked independently of the APIC code.
While we're at it, change the apic_* prefix into kvm_* since the
functions are used from the i8259 PIC (i.e. not the APIC), too.
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230110095351.611724-2-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This even spares some casts in hot code paths along the way.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230109172347.1830-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This remove a use of 'struct' in the DECLARE_INSTANCE_CHECKER()
macro call, to avoid after a QOM refactor:
hw/intc/xilinx_intc.c:45:1: error: declaration of anonymous struct must be a definition
DECLARE_INSTANCE_CHECKER(struct xlx_pic, XILINX_INTC,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Message-id: 20230109140306.23161-14-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following docs/devel/style.rst guidelines, rename
omap_intr_handler_s -> OMAPIntcState. This also remove a
use of 'struct' in the DECLARE_INSTANCE_CHECKER() macro call.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEIAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCY7e94gAKCRBAov/yOSY+
3+YwA/9JAerEGzZIJfV2+QK4LWONOfIt7Ns5TR93gTjd+9rTsahgSIHRa2XHQLWZ
TwY2eyTf8M+qiVOKa1wTCEfvr/iQwRuJBmsyQ/igdKgylEi9t6GEIG1NeGUxGkkR
sCBJMtcqB4OKIX6PlyRiOm9kJxnNgQuiQ6ZB7uqIcVuYC/wxzA==
=KsDP
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20230106
# gpg: Signature made Fri 06 Jan 2023 06:21:22 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20230106' of https://gitlab.com/gaosong/qemu:
hw/intc/loongarch_pch: Change default irq number of pch irq controller
hw/intc/loongarch_pch_pic: add irq number property
hw/intc/loongarch_pch_msi: add irq number property
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the default irq number of pch pic to 32, so that the irq
number of pch msi is 224(256 - 32), and move the 'PCH_PIC_IRQ_NUM'
macro to pci-host/ls7a.h and add prefix 'VIRT' on it to keep standard
format.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-4-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
With loongarch 7A1000 manual, irq number supported can be set
in PCH_PIC_INT_ID_HI register. This patch adds irq number property
for loongarch_pch_pic, so that virt machine can set different
irq number when pch_pic intc is added.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230104020518.2564263-3-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This patch adds irq number property for loongarch msi interrupt
controller, and remove hard coding irq number macro.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230104020518.2564263-2-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
The pending register upper limit is currently set to
plic->num_sources >> 3, which is wrong, e.g.: considering
plic->num_sources is 7, the upper limit becomes 0 which fails
the range check if reading the pending register at pending_base.
Fixes: 1e24429e40 ("SiFive RISC-V PLIC Block")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-16-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the default value of "num-sources" property is zero,
which does not make a lot of sense, as in sifive_plic_realize()
we see s->bitfield_words is calculated by:
s->bitfield_words = (s->num_sources + 31) >> 5;
if the we don't configure "num-sources" property its default value
zero makes s->bitfield_words zero too, which isn't true because
interrupt source 0 still occupies one word.
Let's change the default value to 1 meaning that only interrupt
source 0 is supported by default and a sanity check in realize().
While we are here, add a comment to describe the exact meaning of
this property that the number should include interrupt source 0.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-9-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The realize() callback has an errp for us to propagate the error up.
While we are here, correct the wrong multi-line comment format.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PLIC config parser can only handle legal config string
like "MS,MS". However if a config string like ",MS,MS,,MS,MS,," is
given the parser won't get the correct configuration.
This commit improves the config parser to make it more robust.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-7-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
H-mode has been removed since priv spec 1.10. Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in both riscv_aplic_realize() and
riscv_imsic_realize().
Select MSI_NONBROKEN in RISCV_APLIC and RISCV_IMSIC.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-2-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
hw/pci/Kconfig says MSI_NONBROKEN should be selected by interrupt
controllers regardless of how MSI is implemented. msi_nonbroken is
initialized to true in sifive_plic_realize().
Let SIFIVE_PLIC select MSI_NONBROKEN and drop the selection from
RISC-V machines.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the number of interrupt is not multiple of 32, PLIC will have
out-of-bound access to source_priority array. Compute the number of
interrupt in the last word to avoid this out-of-bound access of array.
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221127165753.30533-1-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 40244040a7 changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Convert the TYPE_ICS class to 3-phase reset; this will allow us
to convert the TYPE_PHB3_MSI class which inherits from it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-7-peter.maydell@linaro.org
The realize method for the TYPE_ICS class uses qemu_register_reset()
to register a reset handler, as a workaround for the fact that
currently objects which directly inherit from TYPE_DEVICE don't get
automatically reset. However, the reset function directly calls
ics_reset(), which is the function that implements the legacy reset
method. This means that only the parent class's data gets reset, and
a subclass which also needs to handle reset, like TYPE_PHB3_MSI, has
to register its own reset function.
Make the TYPE_ICS reset function call device_cold_reset() instead:
this will handle reset for both the parent class and the subclass,
and will work whether the classes are using legacy reset or 3-phase
reset. This allows us to remove the reset function that the subclass
currently has to set up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-6-peter.maydell@linaro.org
Convert the TYPE_KVM_ARM_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-10-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-9-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_ITS_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-8-peter.maydell@linaro.org
Convert the TYPE_KVM_ARM_GICV3 device to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-7-peter.maydell@linaro.org
Convert the TYPE_ARM_GICV3_COMMON parent class to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-6-peter.maydell@linaro.org
Now we have converted TYPE_ARM_GIC_COMMON, we can convert the
TYPE_ARM_GIC_KVM subclass to 3-phase reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221109161444.3397405-5-peter.maydell@linaro.org
Convert the TYPE_ARM_GIC_COMMON device to 3-phase reset. This is a
simple no-behaviour-change conversion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221109161444.3397405-4-peter.maydell@linaro.org
The ARM GICv3 TRM describes that the ITLinesNumber field of GICD_TYPER
register:
"indicates the maximum SPI INTID that the GIC implementation supports"
As SPI #0 is absolute IRQ #32, the max SPI INTID should have accounted
for the internal 16x SGI's and 16x PPI's. However, the original GICv3
model subtracted off the SGI/PPI. Cosmetically this can be seen at OS
boot (Linux) showing 32 shy of what should be there, i.e.:
[ 0.000000] GICv3: 224 SPIs implemented
Though in hw/arm/virt.c, the machine is configured for 256 SPI's. ARM
virt machine likely doesn't have a problem with this because the upper
32 IRQ's don't actually have anything meaningful wired. But, this does
become a functional issue on a custom use case which wants to make use
of these IRQ's. Additionally, boot code (i.e. TF-A) will only init up
to the number (blocks of 32) that it believes to actually be there.
Signed-off-by: Luke Starrett <lukes@xsightlabs.com>
Message-id: AM9P193MB168473D99B761E204E032095D40D9@AM9P193MB1684.EURP193.PROD.OUTLOOK.COM
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
a66a24585f (hw/intc/arm_gic: Implement read of GICC_IIDR) implemented
this for the CPU interface register. The fact we don't implement it
shows up when running Xen with -d guest_error which is definitely
wrong because the guest is perfectly entitled to read it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
gic_dist_readb was returning a word value which just happened to work
as a result of the way we OR the data together. Lets fix it so only
the explicit byte is returned for each part of GICD_TYPER. I've
changed the return type to uint8_t although the overflow is only
detected with an explicit -Wconversion.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With commit 39f29e5993 ("hw/intc/arm_gicv3: Use correct number of
priority bits for the CPU") the number of priority bits was changed from
the maximum value 8 to typically 5. As a consequence a few of the lowest
bits in ICC_PMR_EL1 becomes RAZ/WI. However prior to this patch one of
these bits was still used since the supplied priority value is masked
before it's eventually right shifted with one bit. So the bit is not
lost as one might expect when the register is read again.
The Linux kernel depends on lowest valid bit to be reset to zero, see
commit 33625282adaa ("irqchip/gic-v3: Probe for SCR_EL3 being clear
before resetting AP0Rn") for details.
So fix this by masking the priority value after it may have been right
shifted by one bit.
Cc: qemu-stable@nongnu.org
Fixes: 39f29e5993 ("hw/intc/arm_gicv3: Use correct number of priority bits for the CPU")
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
1. When cpu read or write extioi COREISR reg, it should access
the reg belonged to itself, so the cpu index of 's->coreisr'
is current cpu number. Using MemTxAttrs' requester_id to get
the cpu index.
2. it need not to mask 0x1f when calculate the coreisr array index.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221021015307.2570844-3-yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Converting the MemoryRegionOps read/write handlers to
with_attrs in LoongArch extioi emulation.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221021015307.2570844-2-yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
All that is left in mac.h now belongs to the nvram emulation so rename
it accordingly and only include it where it is really used.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <b82449369f718c0e207fe8c332fab550fa0230c0.1666957578.git.balaton@eik.bme.hu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
In ipi_send function, it should not to set irq before
writing data to dest cpu iocsr space, as the irq will
trigger after data writing.
When call this function 'address_space_stl()', it will
trigger loongarch_ipi_writel(), the addr arg is 0x1008
('CORE_SET_OFF'), and qemu_irq_raise will be called in
this case.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220930095139.867115-3-yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
PLIC spec [1] requires interrupt source priority registers are WARL
field and the number of supported priority is power-of-2 to simplify SW
discovery.
Existing QEMU RISC-V machine (e.g. shakti_c) don't strictly follow PLIC
spec, whose number of supported priority is not power-of-2. Just change
each bit of interrupt priority register to WARL field when the number of
supported priority is power-of-2.
[1] https://github.com/riscv/riscv-plic-spec/blob/master/riscv-plic.adoc#interrupt-priorities
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Clément Chigot <chigot@adacore.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221003041440.2320-3-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The maximum priority level is hard-coded when writing to interrupt
priority register. However, when writing to priority threshold register,
the maximum priority level is from num_priorities Property which is
configured by platform.
Also change interrupt priority register to use num_priorities Property
in maximum priority level.
Signed-off-by: Emmanuel Blot <emmanuel.blot@sifive.com>
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221003041440.2320-2-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use autofree heap allocation instead of variable-length
array on the stack.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220819153931.3147384-8-peter.maydell@linaro.org
Historically, The mtime/mtimecmp has been part of the CPU because
they are per hart entities. However, they actually belong to aclint
which is a MMIO device.
Move them to the ACLINT device. This also emulates the real hardware
more closely.
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-2-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The arch review of AIA spec is completed and we now have official
extension names for AIA: Smaia (M-mode AIA CSRs) and Ssaia (S-mode
AIA CSRs).
Refer, section 1.6 of the latest AIA v0.3.1 stable specification at
https://github.com/riscv/riscv-aia/releases/download/0.3.1-draft.32/riscv-interrupts-032.pdf)
Based on above, we update QEMU RISC-V to:
1) Have separate config options for Smaia and Ssaia extensions
which replace RISCV_FEATURE_AIA in CPU features
2) Not generate AIA INTC compatible string in virt machine
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220820042958.377018-1-apatel@ventanamicro.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Make ppc-uic a subclass of ppc4xx-dcr-device which will handle the cpu
link and make it uniform with the other PPC4xx devices.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <eb548130cf60aea8a6ea4dba4dee1686b3cabc3d.1660746880.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220707163720.1421716-5-berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since commit 40244040a7, multi-socket configuration with plic is
broken as the hartid for second socket is calculated incorrectly.
The hartid stored in addr_config already includes the offset
for the base hartid for that socket. Adding it again would lead
to segfault while creating the plic device for the virt machine.
qdev_connect_gpio_out was also invoked with incorrect number of gpio
lines.
Fixes: 40244040a7 (hw/intc: sifive_plic: Avoid overflowing the addr_config buffer)
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220723090335.671105-1-atishp@rivosinc.com>
[ Changes by AF:
- Change the qdev_connect_gpio_out() numbering
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
