At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
changed the value of VIRT_IRQCHIP_NUM_SOURCES from 127 to 53, which
is VIRTIO_NDEV and also used as the value of "riscv,ndev" property
in the dtb. Unfortunately this is wrong as VIRT_IRQCHIP_NUM_SOURCES
should include interrupt source 0 but "riscv,ndev" does not.
While we are here, we also fix the comments of platform bus irq range
which is now "64 to 96", but should be "64 to 95", introduced since
commit 1832b7cb3f ("hw/riscv: virt: Create a platform bus").
Fixes: 28d8c28120 ("hw/riscv: virt: Add optional AIA IMSIC support to virt machine")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-13-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Per chapter 6.5.2 in [1], the number of interupt sources including
interrupt source 0 should be 187.
[1] PolarFire SoC MSS TRM:
https://ww1.microchip.com/downloads/aemDocuments/documents/FPGA/ProductDocuments/ReferenceManuals/PolarFire_SoC_FPGA_MSS_Technical_Reference_Manual_VC.pdf
Fixes: 56f6e31e7b ("hw/riscv: Initial support for Microchip PolarFire SoC Icicle Kit board")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221211030829.802437-10-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The system controller on PolarFire SoC is access via a mailbox. The
control registers for this mailbox lie in the "IOSCB" region & the
interrupt is cleared via write to the "SYSREG" region. It also has a
QSPI controller, usually connected to a flash chip, that is used for
storing FPGA bitstreams and used for In-Application Programming (IAP).
Linux has an implementation of the system controller, through which the
hwrng is accessed, leading to load/store access faults.
Add the QSPI as unimplemented and a very basic (effectively
unimplemented) version of the system controller's mailbox. Rather than
purely marking the regions as unimplemented, service the mailbox
requests by reporting failures and raising the interrupt so a guest can
better handle the lack of support.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221117225518.4102575-4-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Fabric Interconnect Controllers provide interfaces between the FPGA
fabric and the core complex. There are 5 FICs on PolarFire SoC, numbered
0 through 4. FIC2 is an AXI4 slave interface from the FPGA fabric and
does not show up on the MSS memory map. FIC4 is dedicated to the User
Crypto Processor and does not show up on the MSS memory map either.
FIC 0, 1 & 3 do show up in the MSS memory map and neither FICs 0 or 1
are represented in QEMU, leading to load access violations while booting
Linux for Icicle if PCIe is enabled as the root port is connected via
either FIC 0 or 1.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-Id: <20221117225518.4102575-3-conor@kernel.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The imsic DT binding[1] has changed and no longer require an ipi-id.
The latest IMSIC driver dynamically allocates ipi id if slow-ipi
is not defined.
Get rid of the unused dt property which may lead to confusion.
[1] https://lore.kernel.org/lkml/20221111044207.1478350-5-apatel@ventanamicro.com/
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221122080529.1692533-1-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adds the updated `aon_timer` base as an unimplemented device. This is
used by TockOS, patch ensures the guest doesn't hit load faults.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221025043335.339815-3-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch updates the OpenTitan model to match
the specified register layout as per [1]. Which is also the latest
commit of OpenTitan supported by TockOS.
Note: Pinmux and Padctrl has been merged into Pinmux [2][3], this patch removes
any references to Padctrl. Note: OpenTitan doc [2] has not yet specified
much detail regarding this, except for a note that states `TODO: this
section needs to be updated to reflect the pinmux/padctrl merger`
[1] d072ac505f/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h
[2] https://docs.opentitan.org/hw/top_earlgrey/doc/design/
[3] https://docs.opentitan.org/hw/ip/pinmux/doc/#overview
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20221025043335.339815-2-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To boot S-mode firmware payload like EDK2 from persistent
flash storage, qemu needs to pass the flash address as the
next_addr in fw_dynamic_info to the opensbi.
When both -kernel and -pflash options are provided in command line,
the kernel (and initrd if -initrd) will be copied to fw_cfg table.
The S-mode FW will load the kernel/initrd from fw_cfg table.
If only pflash is given but not -kernel, then it is the job of
of the S-mode firmware to locate and load the kernel.
In either case, update the kernel_entry with the flash address
so that the opensbi can jump to the entry point of the S-mode
firmware.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221004092351.18209-4-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFiveEState inherits from SysBusDevice while it's TypeInfo claims it to
inherit from TYPE_MACHINE. This is an inconsistency which can cause
undefined behavior such as memory corruption.
Change SiFiveEState to inherit from MachineState since it is registered
as a machine.
Fixes: 0869490b1c ("riscv: sifive_e: Manually define the machine")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220922075232.33653-1-shentey@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the OpenTitan hardware the resetvec is fixed at the start of ROM. In
QEMU we don't run the ROM code and instead just jump to the next stage.
This means we need to be a little more flexible about what the resetvec
is.
This patch allows us to set the resetvec from the command line with
something like this:
-global driver=riscv.lowrisc.ibex.soc,property=resetvec,value=0x20000400
This way as the next stage changes we can update the resetvec.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220914101108.82571-4-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When optional AIA PLIC support was added the to the virt machine, the
address cells property was removed leading the issues with dt-validate
on a dump from the virt machine:
/stuff/qemu/qemu.dtb: plic@c000000: '#address-cells' is a required property
From schema: /stuff/linux/Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
Add back the property to suppress the warning.
Reported-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Message-id: 20220810184612.157317-3-mail@conchuod.ie
Link: https://lore.kernel.org/linux-riscv/20220803170552.GA2250266-robh@kernel.org/
Fixes: e6faee6585 ("hw/riscv: virt: Add optional AIA APLIC support to virt machine")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Booting using "Direct Kernel Boot" for PolarFire SoC & skipping u-boot
entirely is probably not advisable, but it does at least show signs of
life. Recent Linux kernel versions make use of peripherals that are
missing definitions in QEMU and lead to kernel panics. These issues
almost certain rear their head for other methods of booting, but I was
unable to figure out a suitable HSS version that is recent enough to
support these peripherals & works with QEMU.
With these peripherals added, booting a kernel with the following hangs
hangs waiting for the system controller's hwrng, but the kernel no
longer panics. With the Linux driver for hwrng disabled, it boots to
console.
qemu-system-riscv64 -M microchip-icicle-kit \
-m 2G -smp 5 \
-kernel $(vmlinux_bin) \
-dtb $(dtb)\
-initrd $(initramfs) \
-display none -serial null \
-serial stdio
More peripherals are added than strictly required to fix the panics in
the hopes of avoiding a replication of this problem in the future.
Some of the peripherals which are in the device tree for recent kernels
are implemented in the FPGA fabric. The eMMC/SD mux, which exists as
an unimplemented device is replaced by a wider entry. This updated
entry covers both the mux & the remainder of the FPGA fabric connected
to the MSS using Fabric Interrconnect (FIC) 3.
Link: https://github.com/polarfire-soc/icicle-kit-reference-design#fabric-memory-map
Link: https://ww1.microchip.com/downloads/aemDocuments/documents/FPGA/ProductDocuments/SupportingCollateral/V1_4_Register_Map.zip
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220813135127.2971754-1-mail@conchuod.ie>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following patch updates opentitan to match the new configuration,
as per, lowRISC/opentitan@217a0168ba
Note: with this patch we now skip the usage of the opentitan
`boot_rom`. The Opentitan boot rom contains hw verification
for devies which we are currently not supporting in qemu. As of now,
the `boot_rom` has no major significance, however, would be good to
support in the future.
Tested by running utests from the latest tock [1]
(that supports this version of OT).
[1] https://github.com/tock/tock/pull/3056
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220812005229.358850-1-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'fdt' param is not being used in riscv_setup_rom_reset_vec().
Simplify the API by removing it. While we're at it, remove the redundant
'return' statement at the end of function.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Vijai Kumar K <vijai@behindbytes.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220728181926.2123771-1-danielhb413@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
Create a platform bus to allow dynamic devices to be connected. This is
based on the ARM implementation.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-4-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the binary and device tree loading code to the machine done
notifier. This allows us to prepare for editing the device tree as part
of the notifier.
This is based on similar code in the ARM virt machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-2-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current riscv_load_fdt() forces fdt_load_addr to be placed at a dram address within 3GB,
but not all platforms have dram_base within 3GB.
This patch adds an exception for dram base not within 3GB,
which will place fdt at dram_end align 16MB.
riscv_setup_rom_reset_vec() also needs to be modified
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220419115945.37945-1-dylan@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch updates the SPI_DEVICE, SPI_HOST0, SPI_HOST1
base addresses. Also adds these as unimplemented devices.
The address references can be found [1].
[1] 6c317992fb/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h (L107)
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220218063839.405082-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To facilitate software development of RISC-V systems with large number
of HARTs, we increase the maximum number of allowed CPUs to 512 (2^9).
We also add a detailed source level comments about limit defines which
impact the physical address space utilization.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-6-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate AIA APLIC devices only when
"aia=aplic" parameter is passed along with machine name in QEMU
command-line. When "aia=none" or not specified then we fallback
to original PLIC device emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-2-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux supports up to 32 cores for both 32-bit and 64-bit RISC-V, so
let's set that as the maximum for the virt board.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/435
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-9-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-4-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-3-alistair.francis@opensource.wdc.com
Add a generic function that can create the PLIC strings.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-2-alistair.francis@opensource.wdc.com
Using a macro for the PLIC configuration doesn't make the code any
easier to read. Instead it makes it harder to figure out what is going
on, so let's remove it.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20211022060133.3045020-1-alistair.francis@opensource.wdc.com
We extend virt machine to emulate ACLINT devices only when "aclint=on"
parameter is passed along with machine name in QEMU command-line.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-5-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect the Ibex timer to the OpenTitan machine. The timer can trigger
the RISC-V MIE interrupt as well as a custom device interrupt.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 5e7f4e9b4537f863bcb8db1264b840b56ef2a929.1624001156.git.alistair.francis@wdc.com
The OpenSBI BIOS image names are used by many RISC-V machines.
Let's define macros for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Update the OpenTitan interrupt layout to match the latest OpenTitan
bitstreams. This involves changing the Ibex PLIC memory layout and the
UART interrupts.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: e92b696f1809c9fa4410da2e9f23c414db5a6960.1617202791.git.alistair.francis@wdc.com
Connect one shakti uart to the shakti_c machine.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-5-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is a mechanical change to make the fdt available through
MachineState.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-3-alex.bennee@linaro.org>
All other peripherals' IRQs are in the format of decimal value.
Change SIFIVE_U_GEM_IRQ to be consistent.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
