The efi_system_table adds a efi_fdt configuration table.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-9-gaosong@loongson.cn>
The efi_system_table adds a efi_initrd configuration table.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-8-gaosong@loongson.cn>
The efi_system_table adds a efi_boot_memmap configuration table.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-7-gaosong@loongson.cn>
Add init_systab and set boot_info->a2
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-6-gaosong@loongson.cn>
Add init_cmline and set boot_info->a0, a1
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-5-gaosong@loongson.cn>
Load the slave CPU boot code at pflash0 and set
the slave CPU elf_address to VIRT_FLASH0_BASE.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-4-gaosong@loongson.cn>
we load initrd ramdisk after kernel_high address
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240426091551.2397867-3-gaosong@loongson.cn>
Move some boot functions to boot.c and struct
loongarch_boot_info into struct LoongArchMachineState.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240426091551.2397867-2-gaosong@loongson.cn>
We usually check target endianess before swapping values,
so target_words_bigendian() declaration makes sense in
"exec/tswap.h" with the target swapping helpers.
Remove "hw/core/cpu.h" when it was only included to get
the target_words_bigendian() declaration.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20231212123401.37493-16-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
* Implement FEAT_NMI and NMI support in the GICv3
* hw/dma: avoid apparent overflow in soc_dma_set_request
* linux-user/flatload.c: Remove unused bFLT shared-library and ZFLAT code
* Add ResetType argument to Resettable hold and exit phase methods
* Add RESET_TYPE_SNAPSHOT_LOAD ResetType
* Implement STM32L4x5 USART
-----BEGIN PGP SIGNATURE-----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=WEsU
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20240425' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Implement FEAT_NMI and NMI support in the GICv3
* hw/dma: avoid apparent overflow in soc_dma_set_request
* linux-user/flatload.c: Remove unused bFLT shared-library and ZFLAT code
* Add ResetType argument to Resettable hold and exit phase methods
* Add RESET_TYPE_SNAPSHOT_LOAD ResetType
* Implement STM32L4x5 USART
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmYqMhMZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3uVlD/47U3zYP33y4+wJcRScC0QI
# jYd82jS7GhD5YP5QPrIEMaSbDwtYGi4Rez1taaHvZ2fWLg2gE973iixmTaM2mXCd
# xPEqMsRXkFrQnC89K5/v9uR04AvHxoM8J2mD2OKnUT0RVBs38WxCUMLETBsD18/q
# obs1RzDRhEs5BnwwPMm5HI1iQeVvDRe/39O3w3rZfA8DuqerrNOQWuJd43asHYjO
# Gc1QzCGhALlXDoqk11IzjhJ7es8WbJ5XGvrSNe9QLGNJwNsu9oi1Ez+5WK2Eht9r
# eRvGNFjH4kQY1YCShZjhWpdzU9KT0+80KLirMJFcI3vUztrYZ027/rMyKLHVOybw
# YAqgEUELwoGVzacpaJg73f77uknKoXrfTH25DfoLX0yFCB35JHOPcjU4Uq1z1pfV
# I80ZcJBDJ95mXPfyKLrO+0IyVBztLybufedK2aiH16waEGDpgsJv66FB2QRuQBYW
# O0i6/4DEUZmfSpOmr8ct+julz7wCWSjbvo6JFWxzzxvD0M5T3AFKXZI244g1SMdh
# LS8V7WVCVzVJ5mK8Ujp2fVaIIxiBzlXVZrQftWv5rhyDOiIIeP8pdekmPlI6p5HK
# 3/2efzSYNL2UCDZToIq24El/3md/7vHR6DBfBT1/pagxWUstqqLgkJO42jQtTG0E
# JY1cZ/EQY7cqXGrww8lhWA==
# =WEsU
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 25 Apr 2024 03:36:03 AM PDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
* tag 'pull-target-arm-20240425' of https://git.linaro.org/people/pmaydell/qemu-arm: (37 commits)
tests/qtest: Add tests for the STM32L4x5 USART
hw/arm: Add the USART to the stm32l4x5 SoC
hw/char/stm32l4x5_usart: Add options for serial parameters setting
hw/char/stm32l4x5_usart: Enable serial read and write
hw/char: Implement STM32L4x5 USART skeleton
reset: Add RESET_TYPE_SNAPSHOT_LOAD
docs/devel/reset: Update to new API for hold and exit phase methods
hw, target: Add ResetType argument to hold and exit phase methods
scripts/coccinelle: New script to add ResetType to hold and exit phases
allwinner-i2c, adm1272: Use device_cold_reset() for software-triggered reset
hw/misc: Don't special case RESET_TYPE_COLD in npcm7xx_clk, gcr
linux-user/flatload.c: Remove unused bFLT shared-library and ZFLAT code
hw/dma: avoid apparent overflow in soc_dma_set_request
hw/arm/virt: Enable NMI support in the GIC if the CPU has FEAT_NMI
target/arm: Add FEAT_NMI to max
hw/intc/arm_gicv3: Report the VINMI interrupt
hw/intc/arm_gicv3: Report the NMI interrupt in gicv3_cpuif_update()
hw/intc/arm_gicv3: Implement NMI interrupt priority
hw/intc/arm_gicv3: Handle icv_nmiar1_read() for icc_nmiar1_read()
hw/intc/arm_gicv3: Add NMI handling CPU interface registers
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
"cpu.h" is implicitly included. Include it explicitly to
avoid the following error when refactoring headers:
hw/s390x/s390-stattrib.c:86:40: error: use of undeclared identifier 'TARGET_PAGE_SIZE'
len = sac->peek_stattr(sas, addr / TARGET_PAGE_SIZE, buflen, vals);
^
hw/s390x/s390-stattrib.c:94:58: error: use of undeclared identifier 'TARGET_PAGE_MASK'
addr / TARGET_PAGE_SIZE, len, addr & ~TARGET_PAGE_MASK);
^
hw/s390x/s390-stattrib.c:224:40: error: use of undeclared identifier 'TARGET_PAGE_BITS'
qemu_put_be64(f, (start_gfn << TARGET_PAGE_BITS) | STATTR_FLAG_MORE);
^
In file included from hw/s390x/s390-virtio-ccw.c:17:
hw/s390x/s390-virtio-hcall.h:22:27: error: unknown type name 'CPUS390XState'
int s390_virtio_hypercall(CPUS390XState *env);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Eric Farman <farman@linux.ibm.com>
Message-ID: <20240322162822.7391-1-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Module is a level above the core, thereby supporting numa
configuration on the module level can bring user more numa flexibility.
This is the natural further support for module level.
Add module level support in numa configuration.
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Message-ID: <20240424154929.1487382-5-zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add module-id in CpuInstanceProperties, to locate the CPU with module
level.
Suggested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240424154929.1487382-4-zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add "modules" parameter parsing support in -smp.
Suggested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240424154929.1487382-3-zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In x86, module is the topology level above core, which contains a set
of cores that share certain resources (in current products, the resource
usually includes L2 cache, as well as module scoped features and MSRs).
Though smp.clusters could also share the L2 cache resource [1], there
are following reasons that drive us to introduce the new smp.modules:
* As the CPU topology abstraction in device tree [2], cluster supports
nesting (though currently QEMU hasn't support that). In contrast,
(x86) module does not support nesting.
* Due to nesting, there is great flexibility in sharing resources
on cluster, rather than narrowing cluster down to sharing L2 (and
L3 tags) as the lowest topology level that contains cores.
* Flexible nesting of cluster allows it to correspond to any level
between the x86 package and core.
* In Linux kernel, x86's cluster only represents the L2 cache domain
but QEMU's smp.clusters is the CPU topology level. Linux kernel will
also expose module level topology information in sysfs for x86. To
avoid cluster ambiguity and keep a consistent CPU topology naming
style with the Linux kernel, we introduce module level for x86.
The module is, in existing hardware practice, the lowest layer that
contains the core, while the cluster is able to have a higher
topological scope than the module due to its nesting.
Therefore, place the module between the cluster and the core:
drawer/book/socket/die/cluster/module/core/thread
With the above topological hierarchy order, introduce module level
support in MachineState and MachineClass.
[1]: https://lore.kernel.org/qemu-devel/c3d68005-54e0-b8fe-8dc1-5989fe3c7e69@huawei.com/
[2]: https://www.kernel.org/doc/Documentation/devicetree/bindings/cpu/cpu-topology.txt
Suggested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Message-ID: <20240424154929.1487382-2-zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240422200625.2768-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
cpu_physical_memory_write() is declared in "exec/cpu-common.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240418192525.97451-21-philmd@linaro.org>
Since commit 139c1837db ("meson: rename included C source files
to .c.inc"), QEMU standard procedure for included C files is to
use *.c.inc.
Besides, since commit 6a0057aa22 ("docs/devel: make a statement
about includes") this is documented in the Coding Style:
If you do use template header files they should be named with
the ``.c.inc`` or ``.h.inc`` suffix to make it clear they are
being included for expansion.
Therefore rename "hw/elf_ops.h" as "hw/elf_ops.h.inc".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240424173333.96148-2-philmd@linaro.org>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
With returned boolean, there's no need to dereference @errp to check
failure case.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-4-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
So make ct3_build_cdat() return boolean, and this is the preparation for
cxl_doe_cdat_init() returning boolean.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-3-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
So make ct3_load_cdat() return boolean, and this is the preparation for
cxl_doe_cdat_init() returning boolean.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-2-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The cpu-cluster device is only needed for some few arm and riscv
machines. Let's avoid compiling and linking it if it is not really
necessary.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240415065655.130099-3-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
A9MPCORE, ARM11MPCORE and A15MPCORE are defined twice, once in
hw/cpu/Kconfig and once in hw/arm/Kconfig. This is only possible
by accident, since hw/cpu/Kconfig is never included from hw/Kconfig.
Fix it by declaring the switches only in hw/cpu/Kconfig (since the
related files reside in the hw/cpu/ folder) and by making sure that
the file hw/cpu/Kconfig is now properly included from hw/Kconfig.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240415065655.130099-2-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
sprintf() is deprecated on Darwin since macOS 13.0 / XCode 14.1.
Use g_strdup_printf instead.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[rth: Use g_strdup_printf]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240412073346.458116-26-richard.henderson@linaro.org>
sprintf() is deprecated on Darwin since macOS 13.0 / XCode 14.1,
resulting in painful developer experience. Use snprintf() instead.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240411104340.6617-6-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Have applesmc_find_key() return a const pointer.
Since the returned buffers are not modified in
applesmc_io_data_write(), it is pointless to
delete and re-add the keys in the DeviceReset
handler. Add them once in DeviceRealize, and
discard them in the DeviceUnrealize handler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240410180819.92332-1-philmd@linaro.org>
Add the USART to the SoC and connect it to the other implemented devices.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240329174402.60382-5-arnaud.minier@telecom-paris.fr
[PMM: fixed a few checkpatch nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a function to change the settings of the
serial connection.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240329174402.60382-4-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the ability to read and write characters to the
usart using the serial port.
The character transmission is based on the
cmsdk-apb-uart implementation.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240329174402.60382-3-arnaud.minier@telecom-paris.fr
[PMM: fixed a few checkpatch nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the basic infrastructure (register read/write, type...)
to implement the STM32L4x5 USART.
Also create different types for the USART, UART and LPUART
of the STM32L4x5 to deduplicate code and enable the
implementation of different behaviors depending on the type.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240329174402.60382-2-arnaud.minier@telecom-paris.fr
[PMM: update to new reset hold method signature;
fixed a few checkpatch nits]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some devices and machines need to handle the reset before a vmsave
snapshot is loaded differently -- the main user is the handling of
RNG seed information, which does not want to put a new RNG seed into
a ROM blob when we are doing a snapshot load.
Currently this kind of reset handling is supported only for:
* TYPE_MACHINE reset methods, which take a ShutdownCause argument
* reset functions registered with qemu_register_reset_nosnapshotload
To allow a three-phase-reset device to also distinguish "snapshot
load" reset from the normal kind, add a new ResetType
RESET_TYPE_SNAPSHOT_LOAD. All our existing reset methods ignore
the reset type, so we don't need to update any device code.
Add the enum type, and make qemu_devices_reset() use the
right reset type for the ShutdownCause it is passed. This
allows us to get rid of the device_reset_reason global we
were using to implement qemu_register_reset_nosnapshotload().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-7-peter.maydell@linaro.org
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
Rather than directly calling the device's implementation of its 'hold'
reset phase, call device_cold_reset(). This means we don't have to
adjust this callsite when we add another argument to the function
signature for the hold and exit reset methods.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-3-peter.maydell@linaro.org
The npcm7xx_clk and npcm7xx_gcr device reset methods look at
the ResetType argument and only handle RESET_TYPE_COLD,
producing a warning if another reset type is passed. This
is different from how every other three-phase-reset method
we have works, and makes it difficult to add new reset types.
A better pattern is "assume that any reset type you don't know
about should be handled like RESET_TYPE_COLD"; switch these
devices to do that. Then adding a new reset type will only
need to touch those devices where its behaviour really needs
to be different from the standard cold reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-2-peter.maydell@linaro.org
In soc_dma_set_request() we try to set a bit in a uint64_t, but we
do it with "1 << ch->num", which can't set any bits past 31;
any use for a channel number of 32 or more would fail due to
integer overflow.
This doesn't happen in practice for our current use of this code,
because the worst case is when we call soc_dma_init() with an
argument of 32 for the number of channels, and QEMU builds with
-fwrapv so the shift into the sign bit is well-defined. However,
it's obviously not the intended behaviour of the code.
Add casts to force the shift to be done as 64-bit arithmetic,
allowing up to 64 channels.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: afbb5194d4 ("Handle on-chip DMA controllers in one place, convert OMAP DMA to use it.")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Message-id: 20240409115301.21829-1-abelova@astralinux.ru
[PMM: Edit commit message to clarify that this doesn't actually
bite us in our current usage of this code.]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the CPU implements FEAT_NMI, then turn on the NMI support in the
GICv3 too. It's permitted to have a configuration with FEAT_NMI in
the CPU (and thus NMI support in the CPU interfaces too) but no NMI
support in the distributor and redistributor, but this isn't a very
useful setup as it's close to having no NMI support at all.
We don't need to gate the enabling of NMI in the GIC behind a
machine version property, because none of our current CPUs
implement FEAT_NMI, and '-cpu max' is not something we maintain
migration compatibility across versions for. So we can always
enable the GIC NMI support when the CPU has it.
Neither hvf nor KVM support NMI in the GIC yet, so we don't enable
it unless we're using TCG.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240407081733.3231820-25-ruanjinjie@huawei.com
[PMM: Update comment and commit message]
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In vCPU Interface, if the vIRQ has the non-maskable property, report
vINMI to the corresponding vPE.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-23-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In CPU Interface, if the IRQ has the non-maskable property, report NMI to
the corresponding PE.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-22-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If GICD_CTLR_DS bit is zero and the NMI is non-secure, the NMI priority is
higher than 0x80, otherwise it is higher than 0x0. And save the interrupt
non-maskable property in hppi.nmi to deliver NMI exception. Since both GICR
and GICD can deliver NMI, it is both necessary to check whether the pending
irq is NMI in gicv3_redist_update_noirqset and gicv3_update_noirqset.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-21-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement icv_nmiar1_read() for icc_nmiar1_read(), so add definition for
ICH_LR_EL2.NMI and ICH_AP1R_EL2.NMI bit.
If FEAT_GICv3_NMI is supported, ich_ap_write() should consider ICV_AP1R_EL1.NMI
bit. In icv_activate_irq() and icv_eoir_write(), the ICV_AP1R_EL1.NMI bit
should be set or clear according to the Non-maskable property. And the RPR
priority should also update the NMI bit according to the APR priority NMI bit.
By the way, add gicv3_icv_nmiar1_read trace event.
If the hpp irq is a NMI, the icv iar read should return 1022 and trap for
NMI again
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: use cs->nmi_support instead of cs->gic->nmi_support]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-20-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the NMIAR CPU interface registers which deal with acknowledging NMI.
When introduce NMI interrupt, there are some updates to the semantics for the
register ICC_IAR1_EL1 and ICC_HPPIR1_EL1. For ICC_IAR1_EL1 register, it
should return 1022 if the intid has non-maskable property. And for
ICC_NMIAR1_EL1 register, it should return 1023 if the intid do not have
non-maskable property. Howerever, these are not necessary for ICC_HPPIR1_EL1
register.
And the APR and RPR has NMI bits which should be handled correctly.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: Separate out whether cpuif supports NMI from whether the
GIC proper (IRI) supports NMI]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-19-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add GICR_INMIR0 register and support access GICR_INMIR0.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-17-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A SPI, PPI or SGI interrupt can have non-maskable property. So maintain
non-maskable property in PendingIrq and GICR/GICD. Since add new device
state, it also needs to be migrated, so also save NMI info in
vmstate_gicv3_cpu and vmstate_gicv3.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-16-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So far, there is no FEAT_GICv3_NMI support in the in-kernel GIC, so make it
an error to try to set has-nmi=true for the KVM GICv3.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Message-id: 20240407081733.3231820-15-ruanjinjie@huawei.com
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a property has-nmi to the GICv3 device, and use this to set
the NMI bit in the GICD_TYPER register. This isn't visible to
guests yet because the property defaults to false and we won't
set it in the board code until we've landed all of the changes
needed to implement FEAT_GICV3_NMI.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-14-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wire the new NMI and VINMI interrupt line from the GIC to each CPU if it
is not GICv2.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240407081733.3231820-12-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Augment the GICv3's QOM device interface by adding one
new set of sysbus IRQ line, to signal NMI to each CPU.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240407081733.3231820-11-ruanjinjie@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To control that creating new machine type doesn't affect the previous
types (their compat_props) and to check complex compat_props inheritance
we need qmp command to print machine type compatibility properties.
This patch adds the ability to get list of all the compat_props of the
corresponding supported machines for their comparison via new optional
argument of "query-machines" command. Since information on compatibility
properties can increase the command output by a factor of 40, add an
argument to enable it, default off.
Signed-off-by: Maksim Davydov <davydov-max@yandex-team.ru>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240318213550.155573-3-davydov-max@yandex-team.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The whole RDMA subsystem was deprecated in commit e9a54265f5
("hw/rdma: Deprecate the pvrdma device and the rdma subsystem")
released in v8.2.
Remove:
- PVRDMA device
- generated vmw_pvrdma/ directory from linux-headers
- rdmacm-mux tool from contrib/
Cc: Yuval Shaia <yuval.shaia.ml@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240328130255.52257-2-philmd@linaro.org>
The ALTERA_TIMER was only used by Nios II machines,
which have been removed. Since it has no direct user,
remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240327144806.11319-4-philmd@linaro.org>
The Nios II target is deprecated since v8.2 in commit 9997771bc1
("target/nios2: Deprecate the Nios II architecture").
Remove:
- Buildsys / CI infra
- User emulation
- System emulation (10m50-ghrd & nios2-generic-nommu machines)
- Tests
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Message-Id: <20240327144806.11319-3-philmd@linaro.org>
Address the comment added in commit 4629ed1e98
("qerror: Finally unused, clean up"), from 2015:
/*
* These macros will go away, please don't use
* in new code, and do not add new ones!
*/
Manual change. Remove the definition in
include/qapi/qmp/qerror.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240312141343.3168265-11-armbru@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Address the comment added in commit 4629ed1e98
("qerror: Finally unused, clean up"), from 2015:
/*
* These macros will go away, please don't use
* in new code, and do not add new ones!
*/
Mechanical transformation using sed, and manual cleanup.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240312141343.3168265-5-armbru@redhat.com>
Address the comment added in commit 4629ed1e98
("qerror: Finally unused, clean up"), from 2015:
/*
* These macros will go away, please don't use
* in new code, and do not add new ones!
*/
Mechanical transformation using sed, and manual cleanup.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240312141343.3168265-3-armbru@redhat.com>
- Het's new test cases for "channels"
- Het's fix for a typo for vsock parsing
- Cedric's VFIO error report series
- Cedric's one more patch for dirty-bitmap error reports
- Zhijian's rdma deprecation patch
- Yuan's zeropage optimization to fix double faults on anon mem
- Zhijian's COLO fix on a crash
-----BEGIN PGP SIGNATURE-----
iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZig4HxIccGV0ZXJ4QHJl
ZGhhdC5jb20ACgkQO1/MzfOr1wbQiwD/V5nSJzSuAG4Ra1Fjo+LRG2TT6qk8eNCi
fIytehSw6cYA/0wqarxOF0tr7ikeyhtG3w4xFf44kk6KcPkoVSl1tqoL
=pJmQ
-----END PGP SIGNATURE-----
Merge tag 'migration-20240423-pull-request' of https://gitlab.com/peterx/qemu into staging
Migration pull for 9.1
- Het's new test cases for "channels"
- Het's fix for a typo for vsock parsing
- Cedric's VFIO error report series
- Cedric's one more patch for dirty-bitmap error reports
- Zhijian's rdma deprecation patch
- Yuan's zeropage optimization to fix double faults on anon mem
- Zhijian's COLO fix on a crash
# -----BEGIN PGP SIGNATURE-----
#
# iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZig4HxIccGV0ZXJ4QHJl
# ZGhhdC5jb20ACgkQO1/MzfOr1wbQiwD/V5nSJzSuAG4Ra1Fjo+LRG2TT6qk8eNCi
# fIytehSw6cYA/0wqarxOF0tr7ikeyhtG3w4xFf44kk6KcPkoVSl1tqoL
# =pJmQ
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 23 Apr 2024 03:37:19 PM PDT
# gpg: using EDDSA key B9184DC20CC457DACF7DD1A93B5FCCCDF3ABD706
# gpg: issuer "peterx@redhat.com"
# gpg: Good signature from "Peter Xu <xzpeter@gmail.com>" [unknown]
# gpg: aka "Peter Xu <peterx@redhat.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B918 4DC2 0CC4 57DA CF7D D1A9 3B5F CCCD F3AB D706
* tag 'migration-20240423-pull-request' of https://gitlab.com/peterx/qemu: (26 commits)
migration/colo: Fix bdrv_graph_rdlock_main_loop: Assertion `!qemu_in_coroutine()' failed.
migration/multifd: solve zero page causing multiple page faults
migration: Add Error** argument to add_bitmaps_to_list()
migration: Modify ram_init_bitmaps() to report dirty tracking errors
migration: Add Error** argument to xbzrle_init()
migration: Add Error** argument to ram_state_init()
memory: Add Error** argument to the global_dirty_log routines
migration: Introduce ram_bitmaps_destroy()
memory: Add Error** argument to .log_global_start() handler
migration: Add Error** argument to .load_setup() handler
migration: Add Error** argument to .save_setup() handler
migration: Add Error** argument to qemu_savevm_state_setup()
migration: Add Error** argument to vmstate_save()
migration: Always report an error in ram_save_setup()
migration: Always report an error in block_save_setup()
vfio: Always report an error in vfio_save_setup()
s390/stattrib: Add Error** argument to set_migrationmode() handler
tests/qtest/migration: Fix typo for vsock in SocketAddress_to_str
tests/qtest/migration: Add negative tests to validate migration QAPIs
tests/qtest/migration: Add multifd_tcp_plain test using list of channels instead of uri
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that the log_global*() handlers take an Error** parameter and
return a bool, do the same for memory_global_dirty_log_start() and
memory_global_dirty_log_stop(). The error is reported in the callers
for now and it will be propagated in the call stack in the next
changes.
To be noted a functional change in ram_init_bitmaps(), if the dirty
pages logger fails to start, there is no need to synchronize the dirty
pages bitmaps. colo_incoming_start_dirty_log() could be modified in a
similar way.
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paul Durrant <paul@xen.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hyman Huang <yong.huang@smartx.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Acked-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-12-clg@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Modify all .log_global_start() handlers to take an Error** parameter
and return a bool. Adapt memory_global_dirty_log_start() to interrupt
on the first error the loop on handlers. In such case, a rollback is
performed to stop dirty logging on all listeners where it was
previously enabled.
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Paul Durrant <paul@xen.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-10-clg@redhat.com
[peterx: modify & enrich the comment for listener_add_address_space() ]
Signed-off-by: Peter Xu <peterx@redhat.com>
This will be useful to report errors at a higher level, mostly in VFIO
today.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-9-clg@redhat.com
[peterx: drop comment for ERRP_GUARD, per Markus]
Signed-off-by: Peter Xu <peterx@redhat.com>
The purpose is to record a potential error in the migration stream if
qemu_savevm_state_setup() fails. Most of the current .save_setup()
handlers can be modified to use the Error argument instead of managing
their own and calling locally error_report().
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Harsh Prateek Bora <harshpb@linux.ibm.com>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Cc: John Snow <jsnow@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-8-clg@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
This will prepare ground for future changes adding an Error** argument
to the save_setup() handler. We need to make sure that on failure,
vfio_save_setup() always sets a new error.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-3-clg@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
This will prepare ground for future changes adding an Error** argument
to the save_setup() handler. We need to make sure that on failure,
set_migrationmode() always sets a new error. See the Rules section in
qapi/error.h.
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Thomas Huth <thuth@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Link: https://lore.kernel.org/r/20240320064911.545001-2-clg@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Add a new member "guest_memfd" to memory backends. When it's set
to true, it enables RAM_GUEST_MEMFD in ram_flags, thus private kvm
guest_memfd will be allocated during RAMBlock allocation.
Memory backend's @guest_memfd is wired with @require_guest_memfd
field of MachineState. It avoid looking up the machine in phymem.c.
MachineState::require_guest_memfd is supposed to be set by any VMs
that requires KVM guest memfd as private memory, e.g., TDX VM.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-ID: <20240320083945.991426-8-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Newer 9.1 machine types will default to using the KVM_SEV_INIT2 API for
creating SEV/SEV-ES going forward. However, this API results in guest
measurement changes which are generally not expected for users of these
older guest types and can cause disruption if they switch to a newer
QEMU/kernel version. Avoid this by continuing to use the older
KVM_SEV_INIT/KVM_SEV_ES_INIT APIs for older machine types.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240409230743.962513-4-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM is introducing a new API to create confidential guests, which
will be used by TDX and SEV-SNP but is also available for SEV and
SEV-ES. The API uses the VM type argument to KVM_CREATE_VM to
identify which confidential computing technology to use.
Since there are no other expected uses of VM types, delegate
mc->kvm_type() for x86 boards to the confidential-guest-support
object pointed to by ms->cgs.
For example, if a sev-guest object is specified to confidential-guest-support,
like,
qemu -machine ...,confidential-guest-support=sev0 \
-object sev-guest,id=sev0,...
it will check if a VM type KVM_X86_SEV_VM or KVM_X86_SEV_ES_VM
is supported, and if so use them together with the KVM_SEV_INIT2
function of the KVM_MEMORY_ENCRYPT_OP ioctl. If not, it will fall back to
KVM_SEV_INIT and KVM_SEV_ES_INIT.
This is a preparatory work towards TDX and SEV-SNP support, but it
will also enable support for VMSA features such as DebugSwap, which
are only available via KVM_SEV_INIT2.
Co-developed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use unified confidential_guest_kvm_init() for consistency with
other architectures.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20240229060038.606591-1-xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the unified interface to call confidential guest related kvm_init()
and kvm_reset(), to avoid exposing pef specific functions.
As a bonus, pef.h goes away since there is no direct call from sPAPR
board code to PEF code anymore.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A value 1 of PCAT_COMPAT (bit 0) of MADT.Flags indicates that the system
also has a PC-AT-compatible dual-8259 setup, i.e., the PIC. When PIC
is not enabled (pic=off) for x86 machine, the PCAT_COMPAT bit needs to
be cleared. The PIC probe should then print:
[ 0.155970] Using NULL legacy PIC
However, no such log printed in guest kernel unless PCAT_COMPAT is
cleared.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240403145953.3082491-1-xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a q35 property to check whether or not SMM ranges, e.g. SMRAM, TSEG,
etc... exist for the target platform. TDX doesn't support SMM and doesn't
play nice with QEMU modifying related guest memory ranges.
Signed-off-by: Isaku Yamahata <isaku.yamahata@linux.intel.com>
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240320083945.991426-19-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In mch_realize(), process PAM initialization before SMRAM initialization so
that later patch can skill all the SMRAM related with a single check.
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240320083945.991426-18-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allows to set guest-phys-bits (cpuid leaf 80000008, eax[23:16])
via -cpu $model,guest-phys-bits=$nr.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-ID: <20240318155336.156197-3-kraxel@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Take into account split screen mode close to wrap around, which is the
other special case for dirty memory region computation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The depth == 0 and depth == 15 have to be special cased because
width * depth / 8 does not provide the correct scanline length.
However, thanks to the recent reorganization of vga_draw_graphic()
the correct value of VRAM bits per pixel is available in "bits".
Use it (via the same "bwidth" computation that is used later in
the function), thus restricting the slow path to the wraparound case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the memory-device stubs are needed exactly when the Kconfig symbols are not
needed, move them to hw/mem/.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240408155330.522792-15-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the ramfb stubs are needed exactly when the Kconfig symbols are not
needed, move them to hw/display/ and compile them when ramfb.c is absent.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240408155330.522792-14-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the virtio memory device stubs are needed exactly when the
Kconfig symbol is not enabled, they can be placed in hw/virtio/ and
conditionalized on CONFIG_VIRTIO_MD.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240408155330.522792-12-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the USB stubs are needed exactly when the Kconfig symbols are not
enabled, they can be placed in hw/usb/ and conditionalized on CONFIG_USB.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240408155330.522792-11-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hotplug.c, qdev-hotplug.c and reset.c are not used by user emulation
and need not be included in hwcore_ss. Move them to system_ss, where
they belong, by letting the linker pull in the stubs when needed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20240408155330.522792-8-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 30896374 started to pass the full BlockConf from usb-storage to
scsi-disk, while previously only a few select properties would be
forwarded. This enables the user to set more properties, e.g. the block
size, that are actually taking effect.
However, now the calls to blkconf_apply_backend_options() and
blkconf_blocksizes() in usb_msd_storage_realize() that modify some of
these properties take effect, too, instead of being silently ignored.
This means at least that the block sizes get an unconditional default of
512 bytes before the configuration is passed to scsi-disk.
Before commit 30896374, the property wouldn't be set for scsi-disk and
therefore the device dependent defaults would apply - 512 for scsi-hd,
but 2048 for scsi-cd. The latter default has now become 512, too, which
makes at least Windows 11 installation fail when installing from
usb-storage.
Fix this by simply not calling these functions any more in usb-storage
and passing BlockConf on unmodified (except for the BlockBackend). The
same functions are called by the SCSI code anyway and it sets the right
defaults for the actual media type.
Fixes: 3089637461 ('scsi: Don't ignore most usb-storage properties')
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2260
Reported-by: Jonas Svensson
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Message-id: 20240412144202.13786-1-kwolf@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A last minute fix for a use of a vector after it's released.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmYdBssPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpTHcH/Rtl2jNJ5myZOuEylw+T6/GSvyEne6CoreHK
zUNPxmXY+uJzCskXkJXyd4uIaci5iIH1JC9Tc0FzFYaYrTsoA1dlQridqoajKyN5
E6zjKqepi3sLnvDE1VbZ1kVcNEX2xSAFX++iv4Rbn4HHO49yKR0jNajusTOsq505
NObgNQXK/Yj1q0IXYrWDETV7xywpQqiiAzwnmhi6ac72+trqmPrUXnUulhitWR3K
iZBuGxAHn9c/ilW3J4FeSbqe6sC/AhqUz3RSM6dB+rkpvA0E675T526uVMWxND2H
auE+ou0kzZ8HNit3AHBg8316seHXzWP+ndVEZlifX33HoR1pltY=
=H3M5
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio: bugfix
A last minute fix for a use of a vector after it's released.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmYdBssPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpTHcH/Rtl2jNJ5myZOuEylw+T6/GSvyEne6CoreHK
# zUNPxmXY+uJzCskXkJXyd4uIaci5iIH1JC9Tc0FzFYaYrTsoA1dlQridqoajKyN5
# E6zjKqepi3sLnvDE1VbZ1kVcNEX2xSAFX++iv4Rbn4HHO49yKR0jNajusTOsq505
# NObgNQXK/Yj1q0IXYrWDETV7xywpQqiiAzwnmhi6ac72+trqmPrUXnUulhitWR3K
# iZBuGxAHn9c/ilW3J4FeSbqe6sC/AhqUz3RSM6dB+rkpvA0E675T526uVMWxND2H
# auE+ou0kzZ8HNit3AHBg8316seHXzWP+ndVEZlifX33HoR1pltY=
# =H3M5
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 15 Apr 2024 11:51:55 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu:
virtio-pci: fix use of a released vector
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Real 460EX SoC apparently does not expose a bridge device and having
it appear on PCI bus confuses an AmigaOS file system driver that uses
this to detect which machine it is running on.
Cc: qemu-stable@nongnu.org
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240411192443.B4D644E6026@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Move calculation of mask after the switch which sets the function
number for PIRQ/PINT pins to make sure the state of these pins are
kept track of separately and IRQ is raised if any of them is active.
Cc: qemu-stable@nongnu.org
Fixes: 7e01bd80c1 hw/isa/vt82c686: Bring back via_isa_set_irq()
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240410222543.0EA534E6005@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
During the booting process of the non-standard image, the behavior of the
called function in qemu is as follows:
1. vhost_net_stop() was triggered by guest image. This will call the function
virtio_pci_set_guest_notifiers() with assgin= false,
virtio_pci_set_guest_notifiers(） will release the irqfd for vector 0
2. virtio_reset() was triggered, this will set configure vector to VIRTIO_NO_VECTOR
3.vhost_net_start() was called (at this time, the configure vector is
still VIRTIO_NO_VECTOR) and then call virtio_pci_set_guest_notifiers() with
assgin=true, so the irqfd for vector 0 is still not "init" during this process
4. The system continues to boot and sets the vector back to 0. After that
msix_fire_vector_notifier() was triggered to unmask the vector 0 and meet the crash
To fix the issue, we need to support changing the vector after VIRTIO_CONFIG_S_DRIVER_OK is set.
(gdb) bt
0 __pthread_kill_implementation (threadid=<optimized out>, signo=signo@entry=6, no_tid=no_tid@entry=0)
at pthread_kill.c:44
1 0x00007fc87148ec53 in __pthread_kill_internal (signo=6, threadid=<optimized out>) at pthread_kill.c:78
2 0x00007fc87143e956 in __GI_raise (sig=sig@entry=6) at ../sysdeps/posix/raise.c:26
3 0x00007fc8714287f4 in __GI_abort () at abort.c:79
4 0x00007fc87142871b in __assert_fail_base
(fmt=0x7fc8715bbde0 "%s%s%s:%u: %s%sAssertion `%s' failed.\n%n", assertion=0x5606413efd53 "ret == 0", file=0x5606413ef87d "../accel/kvm/kvm-all.c", line=1837, function=<optimized out>) at assert.c:92
5 0x00007fc871437536 in __GI___assert_fail
(assertion=0x5606413efd53 "ret == 0", file=0x5606413ef87d "../accel/kvm/kvm-all.c", line=1837, function=0x5606413f06f0 <__PRETTY_FUNCTION__.19> "kvm_irqchip_commit_routes") at assert.c:101
6 0x0000560640f884b5 in kvm_irqchip_commit_routes (s=0x560642cae1f0) at ../accel/kvm/kvm-all.c:1837
7 0x0000560640c98f8e in virtio_pci_one_vector_unmask
(proxy=0x560643c65f00, queue_no=4294967295, vector=0, msg=..., n=0x560643c6e4c8)
at ../hw/virtio/virtio-pci.c:1005
8 0x0000560640c99201 in virtio_pci_vector_unmask (dev=0x560643c65f00, vector=0, msg=...)
at ../hw/virtio/virtio-pci.c:1070
9 0x0000560640bc402e in msix_fire_vector_notifier (dev=0x560643c65f00, vector=0, is_masked=false)
at ../hw/pci/msix.c:120
10 0x0000560640bc40f1 in msix_handle_mask_update (dev=0x560643c65f00, vector=0, was_masked=true)
at ../hw/pci/msix.c:140
11 0x0000560640bc4503 in msix_table_mmio_write (opaque=0x560643c65f00, addr=12, val=0, size=4)
at ../hw/pci/msix.c:231
12 0x0000560640f26d83 in memory_region_write_accessor
(mr=0x560643c66540, addr=12, value=0x7fc86b7bc628, size=4, shift=0, mask=4294967295, attrs=...)
at ../system/memory.c:497
13 0x0000560640f270a6 in access_with_adjusted_size
(addr=12, value=0x7fc86b7bc628, size=4, access_size_min=1, access_size_max=4, access_fn=0x560640f26c8d <memory_region_write_accessor>, mr=0x560643c66540, attrs=...) at ../system/memory.c:573
14 0x0000560640f2a2b5 in memory_region_dispatch_write (mr=0x560643c66540, addr=12, data=0, op=MO_32, attrs=...)
at ../system/memory.c:1521
15 0x0000560640f37bac in flatview_write_continue
(fv=0x7fc65805e0b0, addr=4273803276, attrs=..., ptr=0x7fc871e9c028, len=4, addr1=12, l=4, mr=0x560643c66540)
at ../system/physmem.c:2714
16 0x0000560640f37d0f in flatview_write
(fv=0x7fc65805e0b0, addr=4273803276, attrs=..., buf=0x7fc871e9c028, len=4) at ../system/physmem.c:2756
17 0x0000560640f380bf in address_space_write
(as=0x560642161ae0 <address_space_memory>, addr=4273803276, attrs=..., buf=0x7fc871e9c028, len=4)
at ../system/physmem.c:2863
18 0x0000560640f3812c in address_space_rw
(as=0x560642161ae0 <address_space_memory>, addr=4273803276, attrs=..., buf=0x7fc871e9c028, len=4, is_write=true) at ../system/physmem.c:2873
--Type <RET> for more, q to quit, c to continue without paging--
19 0x0000560640f8aa55 in kvm_cpu_exec (cpu=0x560642f205e0) at ../accel/kvm/kvm-all.c:2915
20 0x0000560640f8d731 in kvm_vcpu_thread_fn (arg=0x560642f205e0) at ../accel/kvm/kvm-accel-ops.c:51
21 0x00005606411949f4 in qemu_thread_start (args=0x560642f292b0) at ../util/qemu-thread-posix.c:541
22 0x00007fc87148cdcd in start_thread (arg=<optimized out>) at pthread_create.c:442
23 0x00007fc871512630 in clone3 () at ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81
(gdb)
MST: coding style and typo fixups
Fixes: f9a09ca3ea ("vhost: add support for configure interrupt")
Cc: qemu-stable@nongnu.org
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-ID: <2321ade5f601367efe7380c04e3f61379c59b48f.1713173550.git.mst@redhat.com>
Cc: Lei Yang <leiyang@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Cindy Lu <lulu@redhat.com>
Per "SD Host Controller Standard Specification Version 3.00":
* 2.2.5 Transfer Mode Register (Offset 00Ch)
Writes to this register shall be ignored when the Command
Inhibit (DAT) in the Present State register is 1.
Do not update the TRNMOD register when Command Inhibit (DAT)
bit is set to avoid the present-status register going out of
sync, leading to malicious guest using DMA mode and overflowing
the FIFO buffer:
$ cat << EOF | qemu-system-i386 \
-display none -nographic -nodefaults \
-machine accel=qtest -m 512M \
-device sdhci-pci,sd-spec-version=3 \
-device sd-card,drive=mydrive \
-drive if=none,index=0,file=null-co://,format=raw,id=mydrive \
-qtest stdio
outl 0xcf8 0x80001013
outl 0xcfc 0x91
outl 0xcf8 0x80001001
outl 0xcfc 0x06000000
write 0x9100002c 0x1 0x05
write 0x91000058 0x1 0x16
write 0x91000005 0x1 0x04
write 0x91000028 0x1 0x08
write 0x16 0x1 0x21
write 0x19 0x1 0x20
write 0x9100000c 0x1 0x01
write 0x9100000e 0x1 0x20
write 0x9100000f 0x1 0x00
write 0x9100000c 0x1 0x00
write 0x91000020 0x1 0x00
EOF
Stack trace (part):
=================================================================
==89993==ERROR: AddressSanitizer: heap-buffer-overflow on address
0x615000029900 at pc 0x55d5f885700d bp 0x7ffc1e1e9470 sp 0x7ffc1e1e9468
WRITE of size 1 at 0x615000029900 thread T0
#0 0x55d5f885700c in sdhci_write_dataport hw/sd/sdhci.c:564:39
#1 0x55d5f8849150 in sdhci_write hw/sd/sdhci.c:1223:13
#2 0x55d5fa01db63 in memory_region_write_accessor system/memory.c:497:5
#3 0x55d5fa01d245 in access_with_adjusted_size system/memory.c:573:18
#4 0x55d5fa01b1a9 in memory_region_dispatch_write system/memory.c:1521:16
#5 0x55d5fa09f5c9 in flatview_write_continue system/physmem.c:2711:23
#6 0x55d5fa08f78b in flatview_write system/physmem.c:2753:12
#7 0x55d5fa08f258 in address_space_write system/physmem.c:2860:18
...
0x615000029900 is located 0 bytes to the right of 512-byte region
[0x615000029700,0x615000029900) allocated by thread T0 here:
#0 0x55d5f7237b27 in __interceptor_calloc
#1 0x7f9e36dd4c50 in g_malloc0
#2 0x55d5f88672f7 in sdhci_pci_realize hw/sd/sdhci-pci.c:36:5
#3 0x55d5f844b582 in pci_qdev_realize hw/pci/pci.c:2092:9
#4 0x55d5fa2ee74b in device_set_realized hw/core/qdev.c:510:13
#5 0x55d5fa325bfb in property_set_bool qom/object.c:2358:5
#6 0x55d5fa31ea45 in object_property_set qom/object.c:1472:5
#7 0x55d5fa332509 in object_property_set_qobject om/qom-qobject.c:28:10
#8 0x55d5fa31f6ed in object_property_set_bool qom/object.c:1541:15
#9 0x55d5fa2e2948 in qdev_realize hw/core/qdev.c:292:12
#10 0x55d5f8eed3f1 in qdev_device_add_from_qdict system/qdev-monitor.c:719:10
#11 0x55d5f8eef7ff in qdev_device_add system/qdev-monitor.c:738:11
#12 0x55d5f8f211f0 in device_init_func system/vl.c:1200:11
#13 0x55d5fad0877d in qemu_opts_foreach util/qemu-option.c:1135:14
#14 0x55d5f8f0df9c in qemu_create_cli_devices system/vl.c:2638:5
#15 0x55d5f8f0db24 in qmp_x_exit_preconfig system/vl.c:2706:5
#16 0x55d5f8f14dc0 in qemu_init system/vl.c:3737:9
...
SUMMARY: AddressSanitizer: heap-buffer-overflow hw/sd/sdhci.c:564:39
in sdhci_write_dataport
Add assertions to ensure the fifo_buffer[] is not overflowed by
malicious accesses to the Buffer Data Port register.
Fixes: CVE-2024-3447
Cc: qemu-stable@nongnu.org
Fixes: d7dfca0807 ("hw/sdhci: introduce standard SD host controller")
Buglink: https://bugs.chromium.org/p/oss-fuzz/issues/detail?id=58813
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <CAFEAcA9iLiv1XGTGKeopgMa8Y9+8kvptvsb8z2OBeuy+5=NUfg@mail.gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409145524.27913-1-philmd@linaro.org>
When the MAC Interface Layer (MIL) transmit FIFO is full,
truncate the packet, and raise the Transmitter Error (TXE)
flag.
Broken since model introduction in commit 2a42499017
("LAN9118 emulation").
When using the reproducer from
https://gitlab.com/qemu-project/qemu/-/issues/2267 we get:
hw/net/lan9118.c:798:17: runtime error:
index 2048 out of bounds for type 'uint8_t[2048]' (aka 'unsigned char[2048]')
#0 0x563ec9a057b1 in tx_fifo_push hw/net/lan9118.c:798:43
#1 0x563ec99fbb28 in lan9118_writel hw/net/lan9118.c:1042:9
#2 0x563ec99f2de2 in lan9118_16bit_mode_write hw/net/lan9118.c:1205:9
#3 0x563ecbf78013 in memory_region_write_accessor system/memory.c:497:5
#4 0x563ecbf776f5 in access_with_adjusted_size system/memory.c:573:18
#5 0x563ecbf75643 in memory_region_dispatch_write system/memory.c:1521:16
#6 0x563ecc01bade in flatview_write_continue_step system/physmem.c:2713:18
#7 0x563ecc01b374 in flatview_write_continue system/physmem.c:2743:19
#8 0x563ecbff1c9b in flatview_write system/physmem.c:2774:12
#9 0x563ecbff1768 in address_space_write system/physmem.c:2894:18
...
[*] LAN9118 DS00002266B.pdf, Table 5.3.3 "INTERRUPT STATUS REGISTER"
Cc: qemu-stable@nongnu.org
Reported-by: Will Lester
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2267
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240409133801.23503-3-philmd@linaro.org>
The magic 2048 is explained in the LAN9211 datasheet (DS00002414A)
in chapter 1.4, "10/100 Ethernet MAC":
The MAC Interface Layer (MIL), within the MAC, contains a
2K Byte transmit and a 128 Byte receive FIFO which is separate
from the TX and RX FIFOs. [...]
Note, the use of the constant in lan9118_receive() reveals that
our implementation is using the same buffer for both tx and rx.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240409133801.23503-2-philmd@linaro.org>
AppleSMCData is allocated with g_new0() in applesmc_add_key():
release it with g_free().
Leaked since commit 1ddda5cd36 ("AppleSMC device emulation").
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2272
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240408095217.57239-3-philmd@linaro.org>
QDev core layer always call DeviceReset() after DeviceRealize(),
no need to do it manually. Remove the extra call.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240408095217.57239-2-philmd@linaro.org>
nand_command() and nand_getio() don't check @offset points
into the block, nor the available data length (s->iolen) is
not negative.
In order to fix:
- check the offset is in range in nand_blk_load_NAND_PAGE_SIZE(),
- do not set @iolen if blk_load() failed.
Reproducer:
$ cat << EOF | qemu-system-arm -machine tosa \
-monitor none -serial none \
-display none -qtest stdio
write 0x10000111 0x1 0xca
write 0x10000104 0x1 0x47
write 0x1000ca04 0x1 0xd7
write 0x1000ca01 0x1 0xe0
write 0x1000ca04 0x1 0x71
write 0x1000ca00 0x1 0x50
write 0x1000ca04 0x1 0xd7
read 0x1000ca02 0x1
write 0x1000ca01 0x1 0x10
EOF
=================================================================
==15750==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x61f000000de0
at pc 0x560e61557210 bp 0x7ffcfc4a59f0 sp 0x7ffcfc4a59e8
READ of size 1 at 0x61f000000de0 thread T0
#0 0x560e6155720f in mem_and hw/block/nand.c:101:20
#1 0x560e6155ac9c in nand_blk_write_512 hw/block/nand.c:663:9
#2 0x560e61544200 in nand_command hw/block/nand.c:293:13
#3 0x560e6153cc83 in nand_setio hw/block/nand.c:520:13
#4 0x560e61a0a69e in tc6393xb_nand_writeb hw/display/tc6393xb.c:380:13
#5 0x560e619f9bf7 in tc6393xb_writeb hw/display/tc6393xb.c:524:9
#6 0x560e647c7d03 in memory_region_write_accessor softmmu/memory.c:492:5
#7 0x560e647c7641 in access_with_adjusted_size softmmu/memory.c:554:18
#8 0x560e647c5f66 in memory_region_dispatch_write softmmu/memory.c:1514:16
#9 0x560e6485409e in flatview_write_continue softmmu/physmem.c:2825:23
#10 0x560e648421eb in flatview_write softmmu/physmem.c:2867:12
#11 0x560e64841ca8 in address_space_write softmmu/physmem.c:2963:18
#12 0x560e61170162 in qemu_writeb tests/qtest/videzzo/videzzo_qemu.c:1080:5
#13 0x560e6116eef7 in dispatch_mmio_write tests/qtest/videzzo/videzzo_qemu.c:1227:28
0x61f000000de0 is located 0 bytes to the right of 3424-byte region [0x61f000000080,0x61f000000de0)
allocated by thread T0 here:
#0 0x560e611276cf in malloc /root/llvm-project/compiler-rt/lib/asan/asan_malloc_linux.cpp:145:3
#1 0x7f7959a87e98 in g_malloc (/lib/x86_64-linux-gnu/libglib-2.0.so.0+0x57e98)
#2 0x560e64b98871 in object_new qom/object.c:749:12
#3 0x560e64b5d1a1 in qdev_new hw/core/qdev.c:153:19
#4 0x560e61547ea5 in nand_init hw/block/nand.c:639:11
#5 0x560e619f8772 in tc6393xb_init hw/display/tc6393xb.c:558:16
#6 0x560e6390bad2 in tosa_init hw/arm/tosa.c:250:12
SUMMARY: AddressSanitizer: heap-buffer-overflow hw/block/nand.c:101:20 in mem_and
==15750==ABORTING
Broken since introduction in commit 3e3d5815cb ("NAND Flash memory
emulation and ECC calculation helpers for use by NAND controllers").
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1445
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1446
Reported-by: Qiang Liu <cyruscyliu@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409135944.24997-4-philmd@linaro.org>
Negative offset is meaningless, use unsigned type.
Return a boolean value indicating success.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409135944.24997-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240409135944.24997-2-philmd@linaro.org>
Replace qemu_bh_new_guarded() by virtio_bh_new_guarded()
so the bus and device use the same guard. Otherwise the
DMA-reentrancy protection can be bypassed.
Fixes: CVE-2024-3446
Cc: qemu-stable@nongnu.org
Suggested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240409105537.18308-5-philmd@linaro.org>
Replace qemu_bh_new_guarded() by virtio_bh_new_guarded()
so the bus and device use the same guard. Otherwise the
DMA-reentrancy protection can be bypassed.
Fixes: CVE-2024-3446
Cc: qemu-stable@nongnu.org
Suggested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240409105537.18308-4-philmd@linaro.org>
Introduce virtio_bh_new_guarded(), similar to qemu_bh_new_guarded()
but using the transport memory guard, instead of the device one
(there can only be one virtio device per virtio bus).
Inspired-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20240409105537.18308-2-philmd@linaro.org>
Let's not care about what was changed and update the whole config,
reasons:
1. config->geometry should be updated together with capacity, so we fix
a bug.
2. Vhost-user protocol doesn't say anything about config change
limitation. Silent ignore of changes doesn't seem to be correct.
3. vhost-user-vsock reads the whole config
4. on realize we don't do any checks on retrieved config, so no reason
to care here
Comment "valid for resize only" exists since introduction the whole
hw/block/vhost-user-blk.c in commit
00343e4b54
"vhost-user-blk: introduce a new vhost-user-blk host device",
seems it was just an extra limitation.
Also, let's notify guest unconditionally:
1. So does vhost-user-vsock
2. We are going to reuse the functionality in new cases when we do want
to notify the guest unconditionally. So, no reason to create extra
branches in the logic.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20240329183758.3360733-2-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The set_config callback function vhost_vdpa_device_get_config in
vdpa-dev does not fetch the current device status from the hardware
device, causing the guest os to not receive the latest device status
information.
The hardware updates the config status of the vdpa device and then
notifies the os. The guest os receives an interrupt notification,
triggering a get_config access in the kernel, which then enters qemu
internally. Ultimately, the vhost_vdpa_device_get_config function of
vdpa-dev is called
One scenario encountered is when the device needs to bring down the
vdpa net device. After modifying the status field of virtio_net_config
in the hardware, it sends an interrupt notification. However, the guest
os always receives the STATUS field as VIRTIO_NET_S_LINK_UP.
Signed-off-by: Yuxue Liu <yuxue.liu@jaguarmicro.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240408020003.1979-1-yuxue.liu@jaguarmicro.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the event of writing many chains of descriptors, the device must
write just the id of the last buffer in the descriptor chain, skip
forward the number of descriptors in the chain, and then repeat the
operations for the rest of chains.
Current QEMU code writes all the buffer ids consecutively, and then
skips all the buffers altogether. This is a bug, and can be reproduced
with a VirtIONet device with _F_MRG_RXBUB and without
_F_INDIRECT_DESC:
If a virtio-net device has the VIRTIO_NET_F_MRG_RXBUF feature
but not the VIRTIO_RING_F_INDIRECT_DESC feature,
'VirtIONetQueue->rx_vq' will use the merge feature
to store data in multiple 'elems'.
The 'num_buffers' in the virtio header indicates how many elements are merged.
If the value of 'num_buffers' is greater than 1,
all the merged elements will be filled into the descriptor ring.
The 'idx' of the elements should be the value of 'vq->used_idx' plus 'ndescs'.
Fixes: 86044b24e8 ("virtio: basic packed virtqueue support")
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Wafer <wafer@jaguarmicro.com>
Message-Id: <20240407015451.5228-2-wafer@jaguarmicro.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current handling of invalid virtqueue elements inside the TX/RX virt
queue handlers is wrong.
They are added in a per-stream invalid queue to be processed after the
handler is done examining each message, but the invalid message might
not be specifying any stream_id; which means it's invalid to add it to
any stream->invalid queue since stream could be NULL at this point.
This commit moves the invalid queue to the VirtIOSound struct which
guarantees there will always be a valid temporary place to store them
inside the tx/rx handlers. The queue will be emptied before the handler
returns, so the queue must be empty at any other point of the device's
lifetime.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <virtio-snd-rewrite-invalid-tx-rx-message-handling-v1.manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch improves error handling in virtio_snd_handle_tx_xfer()
and virtio_snd_handle_rx_xfer() in the VirtIO sound driver. Previously,
'goto' statements were used for error paths, leading to unnecessary
processing and potential null pointer dereferences. Now, 'continue' is
used to skip the rest of the current loop iteration for errors such as
message size discrepancies or null streams, reducing crash risks.
ASAN log illustrating the issue addressed:
ERROR: AddressSanitizer: SEGV on unknown address 0x0000000000b4
#0 0x57cea39967b8 in qemu_mutex_lock_impl qemu/util/qemu-thread-posix.c:92:5
#1 0x57cea128c462 in qemu_mutex_lock qemu/include/qemu/thread.h:122:5
#2 0x57cea128d72f in qemu_lockable_lock qemu/include/qemu/lockable.h:95:5
#3 0x57cea128c294 in qemu_lockable_auto_lock qemu/include/qemu/lockable.h:105:5
#4 0x57cea1285eb2 in virtio_snd_handle_rx_xfer qemu/hw/audio/virtio-snd.c:1026:9
#5 0x57cea2caebbc in virtio_queue_notify_vq qemu/hw/virtio/virtio.c:2268:9
#6 0x57cea2cae412 in virtio_queue_host_notifier_read qemu/hw/virtio/virtio.c:3671:9
#7 0x57cea39822f1 in aio_dispatch_handler qemu/util/aio-posix.c:372:9
#8 0x57cea3979385 in aio_dispatch_handlers qemu/util/aio-posix.c:414:20
#9 0x57cea3978eb1 in aio_dispatch qemu/util/aio-posix.c:424:5
#10 0x57cea3a1eede in aio_ctx_dispatch qemu/util/async.c:360:5
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20240322110827.568412-1-zheyuma97@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit cd341fd1ff.
The patch adds non-upstream code in
include/standard-headers/linux/virtio_pci.h
which would make maintainance harder.
Revert for now.
Suggested-by: Jason Wang <jasowang@redhat.com>
Message-Id: <df6b6b465753e754a19459e8cd61416548f89a42.1712569644.git.mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAmYOtvEeHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIf+5oIAJtRPiTP5aUmN4nU
s72NBtgARBJ+5hHl0fqFFlCrG9elO28F1vhT9DwwBOLwihZCnfIXf+SCoE+pvqDw
c+AMN/RnDu+1F4LF93W0ZIr305yGDfVlU+S3vKGtB9G4rcLeBDmNlhui2d0Bqx9R
jwX1y57vcPclObE0KL6AVOfSDPYiVEVQSiTr3j4oW8TqAs2bduEZMRh6esb3XMIA
hmj8mhZAszfh1YvX8ufbxtPQsnNuFMM+Fxgxp0pux8QaI0addDHwVNObRUYlTUZ1
o4xCw7TRXXotaHde/OqZApFECs+md3R7rC2wj7s3ae0ynohHHDFfaB5t1f4pm+kA
/6UN/Jc=
=XwaI
-----END PGP SIGNATURE-----
Merge tag 'qemu-sparc-20240404' of https://github.com/mcayland/qemu into staging
qemu-sparc queue
# -----BEGIN PGP SIGNATURE-----
#
# iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAmYOtvEeHG1hcmsuY2F2
# ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIf+5oIAJtRPiTP5aUmN4nU
# s72NBtgARBJ+5hHl0fqFFlCrG9elO28F1vhT9DwwBOLwihZCnfIXf+SCoE+pvqDw
# c+AMN/RnDu+1F4LF93W0ZIr305yGDfVlU+S3vKGtB9G4rcLeBDmNlhui2d0Bqx9R
# jwX1y57vcPclObE0KL6AVOfSDPYiVEVQSiTr3j4oW8TqAs2bduEZMRh6esb3XMIA
# hmj8mhZAszfh1YvX8ufbxtPQsnNuFMM+Fxgxp0pux8QaI0addDHwVNObRUYlTUZ1
# o4xCw7TRXXotaHde/OqZApFECs+md3R7rC2wj7s3ae0ynohHHDFfaB5t1f4pm+kA
# /6UN/Jc=
# =XwaI
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 04 Apr 2024 15:19:29 BST
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* tag 'qemu-sparc-20240404' of https://github.com/mcayland/qemu:
esp.c: remove explicit setting of DRQ within ESP state machine
esp.c: ensure esp_pdma_write() always calls esp_fifo_push()
esp.c: update esp_fifo_{push, pop}() to call esp_update_drq()
esp.c: introduce esp_update_drq() and update esp_fifo_{push, pop}_buf() to use it
esp.c: move esp_set_phase() and esp_get_phase() towards the beginning of the file
esp.c: prevent cmdfifo overflow in esp_cdb_ready()
esp.c: rework esp_cdb_length() into esp_cdb_ready()
esp.c: don't assert() if FIFO empty when executing non-DMA SELATNS
esp.c: introduce esp_fifo_push_buf() function for pushing to the FIFO
esp.c: change esp_fifo_pop_buf() to take ESPState
esp.c: use esp_fifo_push() instead of fifo8_push()
esp.c: change esp_fifo_pop() to take ESPState
esp.c: change esp_fifo_push() to take ESPState
esp.c: replace cmdfifo use of esp_fifo_pop() in do_message_phase()
esp.c: replace esp_fifo_pop_buf() with esp_fifo8_pop_buf() in do_message_phase()
esp.c: replace esp_fifo_pop_buf() with esp_fifo8_pop_buf() in do_command_phase()
esp.c: move esp_fifo_pop_buf() internals to new esp_fifo8_pop_buf() function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now the esp_update_drq() is called for all reads/writes to the FIFO, there is
no need to manually raise and lower the DRQ signal.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/611
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1831
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This ensures that esp_update_drq() is called via esp_fifo_push() whenever the
host uses PDMA to transfer data to a SCSI device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This ensures that the DRQ line is always set correctly when reading/writing
single bytes to/from the FIFO.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new function sets the DRQ line correctly according to the current transfer
mode, direction and FIFO contents. Update esp_fifo_push_buf() and esp_fifo_pop_buf()
to use it so that DRQ is always set correctly when reading/writing multiple bytes
to/from the FIFO.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This allows these functions to be used earlier in the file without needing a
separate forward declaration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
During normal use the cmdfifo will never wrap internally and cmdfifo_cdb_offset
will always indicate the start of the SCSI CDB. However it is possible that a
malicious guest could issue an invalid ESP command sequence such that cmdfifo
wraps internally and cmdfifo_cdb_offset could point beyond the end of the FIFO
data buffer.
Add an extra check to fifo8_peek_buf() to ensure that if the cmdfifo has wrapped
internally then esp_cdb_ready() will exit rather than allow scsi_cdb_length() to
access data outside the cmdfifo data buffer.
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The esp_cdb_length() function is only used as part of a calculation to determine
whether the cmdfifo contains an entire SCSI CDB. Rework esp_cdb_length() into a
new esp_cdb_ready() function which both enables us to handle the case where
scsi_cdb_length() returns -1, plus simplify the logic for its callers.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current logic assumes that at least 1 byte is present in the FIFO when
executing a non-DMA SELATNS command, but this may not be the case if the
guest executes an invalid ESP command sequence.
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of pushing data into the FIFO directly with fifo8_push_all(), add a new
esp_fifo_push_buf() function and use it accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that all users of esp_fifo_pop_buf() operate on the main FIFO there is no
need to pass the FIFO explicitly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
There are still a few places that use fifo8_push() instead of esp_fifo_push() in
order to push a value into the FIFO. Update those places to use esp_fifo_push()
instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that all users of esp_fifo_pop() operate on the main FIFO there is no need
to pass the FIFO explicitly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that all users of esp_fifo_push() operate on the main FIFO there is no need
to pass the FIFO explicitly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20240324191707.623175-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The aim is to restrict the esp_fifo_*() functions so that they only operate on
the hardware FIFO. When reading from cmdfifo in do_message_phase() use the
underlying esp_fifo8_pop_buf() function directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The aim is to restrict the esp_fifo_*() functions so that they only operate on
the hardware FIFO. When reading from cmdfifo in do_command_phase() use the
underlying esp_fifo8_pop_buf() function directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Update esp_fifo_pop_buf() to be a simple wrapper onto the new esp_fifo8_pop_buf()
function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240324191707.623175-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This modification ensures that in scenarios where the buffer size is
insufficient for a zone report, the function will now properly set an
error status and proceed to a cleanup label, instead of merely
returning.
The following ASAN log reveals it:
==1767400==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 312 byte(s) in 1 object(s) allocated from:
#0 0x64ac7b3280cd in malloc llvm/compiler-rt/lib/asan/asan_malloc_linux.cpp:129:3
#1 0x735b02fb9738 in g_malloc (/lib/x86_64-linux-gnu/libglib-2.0.so.0+0x5e738)
#2 0x64ac7d23be96 in virtqueue_split_pop hw/virtio/virtio.c:1612:12
#3 0x64ac7d23728a in virtqueue_pop hw/virtio/virtio.c:1783:16
#4 0x64ac7cfcaacd in virtio_blk_get_request hw/block/virtio-blk.c:228:27
#5 0x64ac7cfca7c7 in virtio_blk_handle_vq hw/block/virtio-blk.c:1123:23
#6 0x64ac7cfecb95 in virtio_blk_handle_output hw/block/virtio-blk.c:1157:5
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Message-id: 20240404120040.1951466-1-zheyuma97@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If no bytes are there to process in the message in phase,
the input data latch (s->sidl) is set to s->msg[-1]. Just
do nothing since no DMA is performed.
Reported-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Horizontal pel panning bit 3 is only used in text mode. In graphics
mode, it can be treated as if it was zero, thus not extending the
dirty memory region.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When pel panning is active, one more byte is read from each of the VGA
memory planes. This has to be accounted in the computation of region_end,
otherwise vga_draw_graphic() fails an assertion:
qemu-system-i386: ../system/physmem.c:946: cpu_physical_memory_snapshot_get_dirty: Assertion `start + length <= snap->end' failed.
Reported-by: Helge Konetzka <hk@zapateado.de>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2244
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the computation of region_start and region_end after the value of
"bits" is known. This makes it possible to distinguish modes that
support horizontal pel panning from modes that do not.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two sets of conditionals using the shift control bits: one to
verify the palette and adjust disp_width, one to compute the "v" and
"bits" variables. Merge them into one, with the extra benefit that
we now have the "bits" value available early and can use it to
compute region_end.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When vhost-user or vhost-kernel is handling virtio net datapath,
QEMU should not touch used ring.
But with vhost-user socket reconnect scenario, in a very rare case
(has pending kick event). VRING_USED_F_NO_NOTIFY is set by QEMU in
following code path:
#0 virtio_queue_split_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:511
#1 0x0000559d6dbf033b in virtio_queue_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:576
#2 0x0000559d6dbbbdbc in virtio_net_handle_tx_bh (vdev=0x559d703a6aa0, vq=0x7ff5f4c920a8) at ../hw/net/virtio-net.c:2801
#3 0x0000559d6dbf4791 in virtio_queue_notify_vq (vq=0x7ff5f4c920a8) at ../hw/virtio/virtio.c:2248
#4 0x0000559d6dbf79da in virtio_queue_host_notifier_read (n=0x7ff5f4c9211c) at ../hw/virtio/virtio.c:3525
#5 0x0000559d6d9a5814 in virtio_bus_cleanup_host_notifier (bus=0x559d703a6a20, n=1) at ../hw/virtio/virtio-bus.c:321
#6 0x0000559d6dbf83c9 in virtio_device_stop_ioeventfd_impl (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3774
#7 0x0000559d6d9a55c8 in virtio_bus_stop_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:259
#8 0x0000559d6d9a53e8 in virtio_bus_grab_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:199
#9 0x0000559d6dbf841c in virtio_device_grab_ioeventfd (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3783
#10 0x0000559d6d9bde18 in vhost_dev_enable_notifiers (hdev=0x559d707edd70, vdev=0x559d703a6aa0) at ../hw/virtio/vhost.c:1592
#11 0x0000559d6d89a0b8 in vhost_net_start_one (net=0x559d707edd70, dev=0x559d703a6aa0) at ../hw/net/vhost_net.c:266
#12 0x0000559d6d89a6df in vhost_net_start (dev=0x559d703a6aa0, ncs=0x559d7048d890, data_queue_pairs=31, cvq=0) at ../hw/net/vhost_net.c:412
#13 0x0000559d6dbb5b89 in virtio_net_vhost_status (n=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:311
#14 0x0000559d6dbb5e34 in virtio_net_set_status (vdev=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:392
#15 0x0000559d6dbb60d8 in virtio_net_set_link_status (nc=0x559d7048d890) at ../hw/net/virtio-net.c:455
#16 0x0000559d6da64863 in qmp_set_link (name=0x559d6f0b83d0 "hostnet1", up=true, errp=0x7ffdd76569f0) at ../net/net.c:1459
#17 0x0000559d6da7226e in net_vhost_user_event (opaque=0x559d6f0b83d0, event=CHR_EVENT_OPENED) at ../net/vhost-user.c:301
#18 0x0000559d6ddc7f63 in chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:62
#19 0x0000559d6ddc7fdc in qemu_chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:82
This issue causes guest kernel stop kicking device and traffic stop.
Add vhost_started check in virtio_net_handle_tx_bh to fix this wrong
VRING_USED_F_NO_NOTIFY set.
Signed-off-by: Yajun Wu <yajunw@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20240402045109.97729-1-yajunw@nvidia.com>
[PMD: Use unlikely()]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In xen_evtchn_soft_reset() variable flush_kvm_routes can
be used before being initialized.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Oleg Sviridov <oleg.sviridov@red-soft.ru>
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240329113939.257033-1-artem.chernyshev@red-soft.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
../hw/nvme/ctrl.c:6081:21: error: ‘result’ may be used uninitialized [-Werror=maybe-uninitialized]
It's not obvious that 'result' is set in all code paths. When &result is
a returned argument, it's even less clear.
Looking at various assignments, 0 seems to be a suitable default value.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-ID: <20240328102052.3499331-18-marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
CXL is based on PCIe. In is pointless to initialize
its context on non-PCI machines.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240327161642.33574-1-philmd@linaro.org>
Similarly to commit 9de9fa5cf2 ("hw/arm/smmu-common: Avoid using
inlined functions with external linkage"):
None of our code base require / use inlined functions with external
linkage. Some places use internal inlining in the hot path. These
two functions are certainly not in any hot path and don't justify
any inlining, so these are likely oversights rather than intentional.
Fix:
C compiler for the host machine: clang (clang 15.0.0 "Apple clang version 15.0.0 (clang-1500.3.9.4)")
...
hw/arm/smmu-common.c:203:43: error: static function 'smmu_hash_remove_by_vmid' is
used in an inline function with external linkage [-Werror,-Wstatic-in-inline]
g_hash_table_foreach_remove(s->iotlb, smmu_hash_remove_by_vmid, &vmid);
^
include/hw/arm/smmu-common.h:197:1: note: use 'static' to give inline function 'smmu_iotlb_inv_vmid' internal linkage
void smmu_iotlb_inv_vmid(SMMUState *s, uint16_t vmid);
^
static
hw/arm/smmu-common.c:139:17: note: 'smmu_hash_remove_by_vmid' declared here
static gboolean smmu_hash_remove_by_vmid(gpointer key, gpointer value,
^
Fixes: ccc3ee3871 ("hw/arm/smmuv3: Add CMDs related to stage-2")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20240313184954.42513-2-philmd@linaro.org>
Change the board revision number and RAM size to 1Gb on 32-bit hosts.
On these systems, RAM has a 2047 MB limit and this breaks the tests.
Fixes: 7785e8ea22 ("hw/arm: Introduce Raspberry PI 4 machine")
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-id: 20240329150155.357043-1-clg@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the group of the highest priority pending interrupt is disabled
via ICC_IGRPEN*, the ICC_HPPIR* registers should return
INTID_SPURIOUS, not the interrupt ID. (See the GIC architecture
specification pseudocode functions ICC_HPPIR1_EL1[] and
HighestPriorityPendingInterrupt().)
Make HPPIR reads honour the group disable, the way we already do
when determining whether to preempt in icc_hppi_can_preempt().
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240328153333.2522667-1-peter.maydell@linaro.org
This fixes the invalid bInterfaceProtocol value 0x04 in the USB audio
AudioControl descriptors. It should be zero. While Linux and Windows
forgive this error, macOS 14 Sonoma does not. The usb-audio device does
not appear in macOS sound settings even though the device is recognized
and shows up in USB system information. According to the USB audio class
specs 1.0-4.0, valid values are 0x00, 0x20, 0x30 and 0x40. (Note also
that Linux prints the warning "unknown interface protocol 0x4, assuming
v1", but then proceeds as if the value was zero.)
This also fixes the invalid wTotalLength value in the multi-channel
setup AudioControl interface header descriptor (used when multi=on
and out.mixing-engine off). The combined length of all the descriptors
there add up to 0x37, not 0x38. In Linux, "lsusb -D ..." displays
incomplete descriptor information when this length is incorrect.
Signed-off-by: Joonas Kankaala <joonas.a.kankaala@gmail.com>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
-----BEGIN PGP SIGNATURE-----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=7UPB
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-for-9.0-3-20240331' of https://gitlab.com/npiggin/qemu into staging
Various fixes for recent regressions and new code.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEETkN92lZhb0MpsKeVZ7MCdqhiHK4FAmYJEQMACgkQZ7MCdqhi
# HK6l0BAAkVf/BXKJxMu3jLvCpK/fBYGytvfHBR9PdWeBwIirqsk3L8eI/Fb5qkMZ
# NMrfECyHR9LTcWb6/Pi/PGciNNWeyleN6IuVBeWfraIFyfHcxpwEKH8P+cXr5EWq
# WDg+1GUt9+FHuAC9UdGZ81UzX7qeI9VfD3wHceqJ/XRU3qjj67DPZjTpsvxuP64+
# N7MhdEM69F34uiIAn1aNCceXiS00dvtu6lDl3+18TzT8sNc6S3qdyxVcqfRhTJfY
# FMZIN3j2hQrVOElEQE9vAOeJyjAQCM+U0y3XZIZHFUw/GTwKV0tm08RFnnxprteG
# 67vR5uXrDEELnU/1PA1YeyaBMA3Z3Nc36XbGf8zTD6rKkS2z0lWMcs72pPIxbMXj
# c4FdnHaE+Q5ngy5s1p6bm5xM7WOEhrsJkgIu2N0weRroe0nAxywDWw3uQlMoV8Oc
# Xet/xM2IKdc0PLzTvFO7xKnW3oqavJ4CX/6XgrGBoMDZKO1JRqaMixGtYKmoH/1h
# 96+jdRbPTZAY8aoiFWW7t065lvdWt74A6QITcn2Kqm04j3MGJfyWMU6dakBzwuri
# PhOkf40o8qn8KN0JNfSO+IXhYVRRotLO/s9H7TEyQiXm25qrGMIF9FErnbDseZil
# rGR4eL0lcwJboYH9RSRWg0NNqpUekvqBzdnS+G0Ad3J+qaMYoik=
# =7UPB
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 31 Mar 2024 08:30:11 BST
# gpg: using RSA key 4E437DDA56616F4329B0A79567B30276A8621CAE
# gpg: Good signature from "Nicholas Piggin <npiggin@gmail.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4E43 7DDA 5661 6F43 29B0 A795 67B3 0276 A862 1CAE
* tag 'pull-ppc-for-9.0-3-20240331' of https://gitlab.com/npiggin/qemu:
tests/avocado: ppc_hv_tests.py set alpine time before setup-alpine
tests/avocado: Fix ppc_hv_tests.py xorriso dependency guard
target/ppc: Do not clear MSR[ME] on MCE interrupts to supervisor
target/ppc: Fix GDB register indexing on secondary CPUs
target/ppc: Restore [H]DEXCR to 64-bits
target/ppc/mmu-radix64: Use correct string format in walk_tree()
hw/ppc/spapr: Include missing 'sysemu/tcg.h' header
spapr: nested: use bitwise NOT operator for flags check
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"sysemu/tcg.h" declares tcg_enabled(), and is implicitly included.
Include it explicitly to avoid the following error when refactoring
headers:
hw/ppc/spapr.c:2612:9: error: call to undeclared function 'tcg_enabled'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
if (tcg_enabled()) {
^
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Check for flag bit in H_GUEST_GETSET_STATE_FLAG_GUEST_WIDE need to use
bitwise NOT operator to ensure no other flag bits are set.
Resolves: Coverity CID 1540008
Resolves: Coverity CID 1540009
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
It is incorrect to have the VIRTIO_NET_HDR_F_NEEDS_CSUM set when
checksum offloading is disabled so clear the bit.
TCP/UDP checksum is usually offloaded when the peer requires virtio
headers because they can instruct the peer to compute checksum. However,
igb disables TX checksum offloading when a VF is enabled whether the
peer requires virtio headers because a transmitted packet can be routed
to it and it expects the packet has a proper checksum. Therefore, it
is necessary to have a correct virtio header even when checksum
offloading is disabled.
A real TCP/UDP checksum will be computed and saved in the buffer when
checksum offloading is disabled. The virtio specification requires to
set the packet checksum stored in the buffer to the TCP/UDP pseudo
header when the VIRTIO_NET_HDR_F_NEEDS_CSUM bit is set so the bit must
be cleared in that case.
Fixes: ffbd2dbd8e ("e1000e: Perform software segmentation for loopback")
Buglink: https://issues.redhat.com/browse/RHEL-23067
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
virtio_net_guest_notifier_pending() and virtio_net_guest_notifier_mask()
checked VIRTIO_NET_F_MQ to know there are multiple queues, but
VIRTIO_NET_F_RSS also enables multiple queues. Refer to n->multiqueue,
which is set to true either of VIRTIO_NET_F_MQ or VIRTIO_NET_F_RSS is
enabled.
Fixes: 68b0a6395f ("virtio-net: align ctrl_vq index for non-mq guest for vhost_vdpa")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
QEMU build fails with
hw/i386/fw_cfg.c:74: undefined reference to `smbios_get_table_legacy'
when it's built with only 'microvm' enabled i.e. with config patch
+++ b/configs/devices/i386-softmmu/default.mak
@@ -26,7 +26,7 @@
# Boards:
#
-CONFIG_ISAPC=y
-CONFIG_I440FX=y
-CONFIG_Q35=y
+CONFIG_ISAPC=n
+CONFIG_I440FX=n
+CONFIG_Q35=n
It happens because I've fogotten/lost smbios_get_table_legacy() stub.
Fix it by adding missing stub as Philippe suggested.
Fixes: b42b0e4daa "smbios: build legacy mode code only for 'pc' machine"
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-ID: <20240326122630.85989-1-imammedo@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The "clock_set_mul_div" function doesn't propagate the clock period
to the children if it is changed (e.g. by enabling/disabling a clock
multiplexer).
This was overlooked during the implementation due to late changes.
This commit propagates the change if the multiplier or divider changes.
Fixes: ec7d83acbd ("hw/misc/stm32l4x5_rcc: Add an internal clock multiplexer object")
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-ID: <20240317103918.44375-2-arnaud.minier@telecom-paris.fr>
[PMD: Check clock_set_mul_div() return value]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20240325152827.73817-4-philmd@linaro.org>
Trivial inlining in preliminary patch to make the next
one easier to review.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20240325152827.73817-3-philmd@linaro.org>
Let clock_set_mul_div() return a boolean value whether the
clock has been updated or not, similarly to clock_set().
Return early when clock_set_mul_div() is called with
same mul/div values the clock has.
Acked-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20240325152827.73817-2-philmd@linaro.org>
The io_timeout property, introduced in c9b6609 (part of 6.0) is
silently overwritten by the hardcoded default value of 30 seconds
(DEFAULT_IO_TIMEOUT) in scsi_generic_realize because that function is
being called after the properties have already been applied.
The property definition already has a default value which is applied
correctly when no value is explicitly set, so we can just remove the
code which overrides the io_timeout completely.
This has been tested by stracing SG_IO operations with the io_timeout
property set and unset and now sets the timeout field in the ioctl
request to the proper value.
Fixes: c9b6609b69 ("scsi: make io_timeout configurable")
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Message-ID: <20240315145831.2531695-1-lorenz@brun.one>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
VDUSE requires that virtqueues are first enabled before the DRIVER_OK
status flag is set; with the current API of the kernel module, it is
impossible to enable the opposite order in our block export code because
userspace is not notified when a virtqueue is enabled.
This requirement also mathces the normal initialisation order as done by
the generic vhost code in QEMU. However, commit 6c482547 accidentally
changed the order for vdpa-dev and broke access to VDUSE devices with
this.
This changes vdpa-dev to use the normal order again and use the standard
vhost callback .vhost_set_vring_enable for this. VDUSE devices can be
used with vdpa-dev again after this fix.
vhost_net intentionally avoided enabling the vrings for vdpa and does
this manually later while it does enable them for other vhost backends.
Reflect this in the vhost_net code and return early for vdpa, so that
the behaviour doesn't change for this device.
Cc: qemu-stable@nongnu.org
Fixes: 6c4825476a ('vdpa: move vhost_vdpa_set_vring_ready to the caller')
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240315155949.86066-1-kwolf@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* Mark devices with user_creatable = false that can crash QEMU otherwise
* Fix s390x TEST-AND-SET TCG instruction emulation
* Move pc955* devices to hw/gpio/
-----BEGIN PGP SIGNATURE-----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=lfZM
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-03-25' of https://gitlab.com/thuth/qemu into staging
* Fix timeouts in Travis-CI jobs
* Mark devices with user_creatable = false that can crash QEMU otherwise
* Fix s390x TEST-AND-SET TCG instruction emulation
* Move pc955* devices to hw/gpio/
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmYBhdgRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbVcfA/9FulEN4HrjD3ObyboA+WfibXURwChui98
# 8LvL/fAGe3BZXQtspuNmPyrKRtIOrIwHJyFuxf2N5+8BuvGhEHQIuvIhQIj/rvfy
# X14KlldmQ3w3HlI3Ud4YiebLyK3AAFC2ApIywzFsnN+HoaHJR2EyDIb+T7OsGJZf
# ZLE/Z7qANxoNeZ+a3+rQR3SVpijyS3fXxDSaILrq2uW4kCCs/55O8Rt3Qb+PFSVd
# fF+OlpG6o+z73ACZc1u9Io4IO1ZZc/NdkmDTNz4HknkvJLTLF6kOECAxLl0ytgAG
# YRzBGKes29Zpa9wn/9rc75/OYNS0Ks+B19sQnijWUNX0zq5FkReXNXiyVcbT7d4p
# 6jFzlFnjj4ifB8uQkZTGcx/lL4s4VkPzF+f7fgHq9CKNrNsx8uca0TyQ8s4y+NGb
# C98kJdHd+QhCcuNnAbifCwuFaxQ8C4BdgzxVbU/sGDKNkINNkiTp+uue4TxnRKvV
# MfhqdnWRvqgZ0Rl4TxqcNfODK72Z1YNv3933OKE/mRJYS1Q529TIq4vfp8WIMsWQ
# 7+ipo4WKXhkiSOJZD6AkCoFum1W8yaDzUDJTw2Xt2bPBL3+FXcQyKkKVUMfzIJ8M
# KLe0Bb9W/pYU1ToTciTP0dkQF/02tG0Vik273445wPgH0x8OyHJkPF/ny1a7lKFO
# 5jreYdMxWdc=
# =lfZM
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 25 Mar 2024 14:10:32 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-03-25' of https://gitlab.com/thuth/qemu:
tests/tcg/s390x: Test TEST AND SET
target/s390x: Use mutable temporary value for op_ts
libqos/virtio.c: Correct 'flags' reading in qvirtqueue_kick
misc/pca955*: Move models under hw/gpio
aspeed: Make the ast1030-a1 SoC not user creatable
aspeed: Make the ast2600-a3 SoC not user creatable
hw/microblaze: Do not allow xlnx-zynqmp-pmu-soc to be created by the user
.travis.yml: Remove the unused xfslib-dev package
.travis.yml: Shorten the runtime of the problematic jobs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PCA9552 and PCA9554 devices are both I2C GPIO controllers and the
PCA9552 also can drive LEDs. Do all the necessary adjustments to move
the models under hw/gpio.
Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20240325134833.1484265-1-clg@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There's no way for the macio_nvram device to report failure to write
data, but we can at least report it to the user with error_report()
as we do in other devices like xlnx-efuse.
Spotted by Coverity.
Resolves: Coverity CID 1507628
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240312183810.557768-6-peter.maydell@linaro.org
In pca9554_get_pin() and pca9554_set_pin(), we try to detect an
incorrect pin value, but we get the condition wrong, using ">"
when ">=" was intended.
This has no actual effect, because in pca9554_initfn() we
use the correct test when creating the properties and so
we'll never be called with an out of range value. However,
Coverity complains about the mismatch between the check and
the later use of the pin value in a shift operation.
Use the correct condition.
Resolves: Coverity CID 1534917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20240312183810.557768-5-peter.maydell@linaro.org
Aspeed SoCs are complex devices that can not be specified on the
command line. Fix that to avoid QEMU aborts.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2227
Fixes: 356b230ed1 ("aspeed/soc : Add AST1030 support")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240319150903.413662-2-clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Aspeed SoCs are complex devices that can not be specified on the
command line. Fix that to avoid QEMU aborts.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2227
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240319150903.413662-1-clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Using xlnx-zynqmp-pmu-soc on the command line causes QEMU to crash:
./qemu-system-microblazeel -M petalogix-ml605 -device xlnx-zynqmp-pmu-soc
**
ERROR:tcg/tcg.c:813:tcg_register_thread: assertion failed: (n < tcg_max_ctxs)
Bail out!
Aborted (core dumped)
Mark the device with "user_creatable = false" to avoid that this can happen.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2229
Message-ID: <20240322183153.1023359-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The timebase-frequency of guest OS should be the same with host
machine. The timebase-frequency value in DTS should be got from
hypervisor when using KVM acceleration.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Message-ID: <20240314061510.9800-1-yongxuan.wang@sifive.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, QEMU only sets the iforce register to 0 and returns early
when claiming the iforce register. However, this may leave mip.meip
remains at 1 if a spurious external interrupt triggered by iforce
register is the only pending interrupt to be claimed, and the interrupt
cannot be lowered as expected.
This commit fixes this issue by calling riscv_aplic_idc_update() to
update the IDC status after the iforce register is claimed.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240321104951.12104-1-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Interrupt number in loop sentence should be base irq plus
loop index, it is missing on checking whether the irq
is pending.
Fixes: 428a6ef439 ("Add vmstate post_load support")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240313093932.2653518-1-maobibo@loongson.cn>
* user device fixes for Aspeed and PowerNV machines
* coverity fix for iommufd
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmX5mm0ACgkQUaNDx8/7
7KE/MQ/9GeX4yNBxY2iTATdmPXwjMw8AtKyfIQb605nIO0ch1Z98ywl5VMwCNohn
ppY9L5bFpEASgRlFVm73X4DGxKyRGpRPqylsvINh0hKciRpmRkELHY3llhnXsd7P
Q197pDtFr54FeX8j4+hSAu4paT97fPENlKn0J6lto2I1cXGcD1LYNDFhysoXdGme
brJgo7KjQJZPZ560ZewskL5FWf3G9EkRjpqd8y0G5OtNmAPgAaahOMHhDCXan182
J89I9CHI5xN45MRfAs8JamSaj/GyNsr4h04WhPa0+VZQ5vsaeW2Ekt4ypj+oAV+p
wykhYzQk4ALZcmmph2flSAtLa7uheI+imyqubMthQCDj3G8onSQBMd5/4WRK6O49
0oE1DpPDEfhlJEQYxaYhOeqeA9iaP+w6V+yE+L5oGlMO66cR7GZsPu0x7kXailbH
IoHw9mO+vMkpuyeP7M3hA8WRFCdFpf1Nn1Ao5Jz3KoiTyJWlIvX5VSaj12sjddQ2
fU9SKu2Q5QqS5uQGakkY64EyUy7RkGIX6zY2NIscVe2lfAfKf3mZwu7OIuLjEy5O
lRn35vWV8fOdRooKoDPTNcdBCaNPi+RApin8chOv5P+F+ie7+Twf9sb1AgH/pIcv
HptvTXbvSFNbbdb+OE8a5qsqTvnrN8d31IXzrWRYsJB07x2IyoA=
=zR3v
-----END PGP SIGNATURE-----
Merge tag 'pull-for-9.0-20240319' of https://github.com/legoater/qemu into staging
aspeed, pnv, vfio queue:
* user device fixes for Aspeed and PowerNV machines
* coverity fix for iommufd
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmX5mm0ACgkQUaNDx8/7
# 7KE/MQ/9GeX4yNBxY2iTATdmPXwjMw8AtKyfIQb605nIO0ch1Z98ywl5VMwCNohn
# ppY9L5bFpEASgRlFVm73X4DGxKyRGpRPqylsvINh0hKciRpmRkELHY3llhnXsd7P
# Q197pDtFr54FeX8j4+hSAu4paT97fPENlKn0J6lto2I1cXGcD1LYNDFhysoXdGme
# brJgo7KjQJZPZ560ZewskL5FWf3G9EkRjpqd8y0G5OtNmAPgAaahOMHhDCXan182
# J89I9CHI5xN45MRfAs8JamSaj/GyNsr4h04WhPa0+VZQ5vsaeW2Ekt4ypj+oAV+p
# wykhYzQk4ALZcmmph2flSAtLa7uheI+imyqubMthQCDj3G8onSQBMd5/4WRK6O49
# 0oE1DpPDEfhlJEQYxaYhOeqeA9iaP+w6V+yE+L5oGlMO66cR7GZsPu0x7kXailbH
# IoHw9mO+vMkpuyeP7M3hA8WRFCdFpf1Nn1Ao5Jz3KoiTyJWlIvX5VSaj12sjddQ2
# fU9SKu2Q5QqS5uQGakkY64EyUy7RkGIX6zY2NIscVe2lfAfKf3mZwu7OIuLjEy5O
# lRn35vWV8fOdRooKoDPTNcdBCaNPi+RApin8chOv5P+F+ie7+Twf9sb1AgH/pIcv
# HptvTXbvSFNbbdb+OE8a5qsqTvnrN8d31IXzrWRYsJB07x2IyoA=
# =zR3v
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 19 Mar 2024 14:00:13 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-for-9.0-20240319' of https://github.com/legoater/qemu:
aspeed/smc: Only wire flash devices at reset
ppc/pnv: I2C controller is not user creatable
vfio/iommufd: Fix memory leak
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed machines have many Static Memory Controllers (SMC), up to
8, which can only drive flash memory devices. Commit 27a2c66c92
("aspeed/smc: Wire CS lines at reset") tried to ease the definitions
of these devices by allowing flash devices from the command line to be
attached to a SSI bus. For that, the wiring of the CS lines of the
Aspeed SMC controller was moved at reset. Two assumptions are made
though, first that the device has a SSI_GPIO_CS GPIO line, which is
not always the case, and second that it is a flash device.
Correct this problem by ensuring that the devices attached to the bus
are of the correct flash type. This fixes a QEMU abort when devices
without a CS line, such as the max111x, are passed on the command
line.
While at it, export TYPE_M25P80 used in the Xilinx Versal Virtual
machine.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2228
Fixes: 27a2c66c92 ("aspeed/smc: Wire CS lines at reset")
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
[ clg: minor fixes in the commit log ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
The I2C controller is a subunit of the processor. Make it so and avoid
QEMU crashes.
$ build/qemu-system-ppc64 -S -machine powernv9 -device pnv-i2c
qemu-system-ppc64: ../hw/ppc/pnv_i2c.c:521: pnv_i2c_realize: Assertion `i2c->chip' failed.
Aborted (core dumped)
Fixes: 263b81ee15 ("ppc/pnv: Add an I2C controller model")
Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Coverity reported a memory leak on variable 'contents' in routine
iommufd_cdev_getfd(). Use g_autofree variables to simplify the exit
path and get rid of g_free() calls.
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Yi Liu <yi.l.liu@intel.com>
Fixes: CID 1540007
Fixes: 5ee3dc7af7 ("vfio/iommufd: Implement the iommufd backend")
Suggested-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20240314152302.2324164-22-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use smbios-entry-point-type='auto' for newer machine types as a workaround
for Windows not detecting SMBIOS tables. Which makes QEMU pick SMBIOS tables
based on configuration (with 2.x preferred and fallback to 3.x if the former
isn't compatible with configuration)
Default compat setting of smbios-entry-point-type after series
for pc/q35 machines:
* 9.0-newer: 'auto'
* 8.1-8.2: '64'
* 8.0-older: '32'
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2008
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-20-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If SMBIOS v2 version is requested but number of cores/threads
are more than it's possible to describe with v2, error out
instead of silently ignoring the fact and filling core/thread
count with bogus values.
This will help caller to decide if it should fallback to
SMBIOSv3 when smbios-entry-point-type='auto'
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-18-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU for some time now uses SMBIOS 3.0 for PC/Q35 machines by
default, however Windows has a bug in locating SMBIOS 3.0
entrypoint and fails to find tables when booted on SeaBIOS
(on UEFI SMBIOS 3.0 tables work fine since firmware hands
over tables in another way)
Missing SMBIOS tables may lead to some issues for guest
though (worst are: possible reactiveation, inability to
get virtio drivers from 'Windows Update')
It's unclear at this point if MS will fix the issue on their
side. So instead of it (or rather in addition) this patch
will try to workaround the issue.
aka, use smbios-entry-point-type=auto to make QEMU try
generating conservative SMBIOS 2.0 tables and if that
fails (due to limits/requested configuration) fallback
to SMBIOS 3.0 tables.
With this in place majority of users will use SMBIOS 2.0
tables which work fine with (Windows + legacy BIOS).
The configurations that is not to possible to describe
with SMBIOS 2.0 will switch automatically to SMBIOS 3.0
(which will trigger Windows bug but there is nothing
QEMU can do here, so go and aks Microsoft to real fix).
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-17-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will help to keep type 4 tables accounting correct in case
SMBIOS tables are built multiple times.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-15-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-14-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current code uses mix of error_report()+exit(1)
and error_setg() to handle errors.
Use newer error_setg() everywhere, beside consistency
it will allow to detect error condition without killing
QEMU and attempt switch-over to SMBIOS3.x tables/entrypoint
in follow up patch.
while at it, clear smbios_tables pointer after freeing.
that will avoid double free if smbios_get_tables() is called
multiple times.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-13-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
basically moving code around without functional change.
And exposing some symbols so that they could be shared
between smbbios.c and new smbios_legacy.c
plus some meson magic to build smbios_legacy.c only
for 'pc' machine and otherwise replace it with stub
if not selected.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-12-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As a preparation to move legacy handling into a separate file,
add prefix 'smbios_' to type0/type1/have_binfile_bitmap/have_fields_bitmap
and expose them in smbios.h so that they can be reused in
legacy and modern code.
Doing it as a separate patch to avoid rename cluttering follow-up
patch which will move legacy code into a separate file.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-11-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be used by follow up patch when legacy handling
is moved out into a separate file.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-10-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
legacy mode doesn't support structures of type 2 and more,
and CLI has a check for '-smbios type' option, however it's
still possible to sneak in type4 as a blob with '-smbios file'
option. However doing the later makes SMBIOS tables broken
since SeaBIOS doesn't expect that.
Rather than trying to add support for type4 to legacy code
(both QEMU and SeaBIOS), simplify smbios_get_table_legacy()
by dropping not relevant check in legacy code and error out
on type4 blob.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
currently smbios_entry_add() preserves internally '-smbios type='
options but tables provided with '-smbios file=' are stored directly
into blob that eventually will be exposed to VM. And then later
QEMU adds default/'-smbios type' entries on top into the same blob.
It makes impossible to generate tables more than once, hence
'immutable' guard was used.
Make it possible to regenerate final blob by storing user provided
blobs into a dedicated area (usr_blobs) and then copy it when
composing final blob. Which also makes handling of -smbios
options consistent.
As side effect of this and previous commits there is no need to
generate legacy smbios_entries at the time options are parsed.
Instead compose smbios_entries on demand from usr_blobs like
it is done for non-legacy SMBIOS tables.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240314152302.2324164-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
clean up smbios_set_defaults() which is reused by legacy
and non legacy machines from being aware of 'legacy' notion
and need to turn it off. And push legacy handling up to
PC machine code where it's relevant.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Acked-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-7-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it makes smbios_validate_table() independent from
smbios_smp_sockets global, which in turn lets
smbios_get_tables() avoid using not related legacy code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
smbios_get_tables() bails out right away if leagacy mode is enabled
and won't generate any SMBIOS tables. At the same time x86 specific
fw_cfg_build_smbios() will genarate legacy tables and then proceed
to preparing temporary mem_array for useless call to
smbios_get_tables() and then discard it.
Drop legacy related check in smbios_get_tables() and return from
fw_cfg_build_smbios() early if legacy tables where built without
proceeding to non legacy part of the function.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Message-Id: <20240314152302.2324164-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Break up long lines to fit under 80/90 char limit.
Fixes: 04f143d828 ("Implement SMBIOS type 9 v2.6")
Fixes: 735eee07d1 ("Implement base of SMBIOS type 9 descriptor.")
Cc: "Felix Wu" <flwu@google.com>
Cc: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
+jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
=C0UU
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
# 1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
# +jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
# uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
# 0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
# 6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
# =C0UU
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Mar 2024 22:03:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (68 commits)
docs/specs/pvpanic: document shutdown event
hw/cxl: Fix missing reserved data in CXL Device DVSEC
hmat acpi: Fix out of bounds access due to missing use of indirection
hmat acpi: Do not add Memory Proximity Domain Attributes Structure targetting non existent memory.
qemu-options.hx: Document the virtio-iommu-pci aw-bits option
hw/arm/virt: Set virtio-iommu aw-bits default value to 48
hw/i386/q35: Set virtio-iommu aw-bits default value to 39
virtio-iommu: Add an option to define the input range width
virtio-iommu: Trace domain range limits as unsigned int
qemu-options.hx: Document the virtio-iommu-pci granule option
virtio-iommu: Change the default granule to the host page size
virtio-iommu: Add a granule property
hw/i386/acpi-build: Add support for SRAT Generic Initiator structures
hw/acpi: Implement the SRAT GI affinity structure
qom: new object to associate device to NUMA node
hw/i386/pc: Inline pc_cmos_init() into pc_cmos_init_late() and remove it
hw/i386/pc: Set "normal" boot device order in pc_basic_device_init()
hw/i386/pc: Avoid one use of the current_machine global
hw/i386/pc: Remove "rtc_state" link again
Revert "hw/i386/pc: Confine system flash handling to pc_sysfw"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/core/machine.c
With a numa set up such as
-numa nodeid=0,cpus=0 \
-numa nodeid=1,memdev=mem \
-numa nodeid=2,cpus=1
and appropriate hmat_lb entries the initiator list is correctly
computed and writen to HMAT as 0,2 but then the LB data is accessed
using the node id (here 2), landing outside the entry_list array.
Stash the reverse lookup when writing the initiator list and use
it to get the correct array index index.
Fixes: 4586a2cb83 ("hmat acpi: Build System Locality Latency and Bandwidth Information Structure(s)")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240307160326.31570-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If qemu is started with a proximity node containing CPUs alone,
it will provide one of these structures to say memory in this
node is directly connected to itself.
This description is arguably pointless even if there is memory
in the node. If there is no memory present, and hence no SRAT
entry it breaks Linux HMAT passing and the table is rejected.
https://elixir.bootlin.com/linux/v6.7/source/drivers/acpi/numa/hmat.c#L444
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240307160326.31570-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On ARM we set 48b as a default (matching SMMUv3 SMMU_IDR5.VAX == 0).
hw_compat_8_2 is used to handle the compatibility for machine types
before 9.0 (default was 64 bits).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <Zhenzhong.duan@intel.com>
Message-Id: <20240307134445.92296-9-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the default input range can extend to 64 bits. On x86,
when the virtio-iommu protects vfio devices, the physical iommu
may support only 39 bits. Let's set the default to 39, as done
for the intel-iommu.
We use hw_compat_8_2 to handle the compatibility for machines
before 9.0 which used to have a virtio-iommu default input range
of 64 bits.
Of course if aw-bits is set from the command line, the default
is overriden.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20240307134445.92296-8-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
aw-bits is a new option that allows to set the bit width of
the input address range. This value will be used as a default for
the device config input_range.end. By default it is set to 64 bits
which is the current value.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240307134445.92296-7-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use %u format to trace domain_range limits.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <20240307134445.92296-6-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We used to set the default granule to 4KB but with VFIO assignment
it makes more sense to use the actual host page size.
Indeed when hotplugging a VFIO device protected by a virtio-iommu
on a 64kB/64kB host/guest config, we current get a qemu crash:
"vfio: DMA mapping failed, unable to continue"
This is due to the hot-attached VFIO device calling
memory_region_iommu_set_page_size_mask() with 64kB granule
whereas the virtio-iommu granule was already frozen to 4KB on
machine init done.
Set the granule property to "host" and introduce a new compat.
The page size mask used before 9.0 was qemu_target_page_mask().
Since the virtio-iommu currently only supports x86_64 and aarch64,
this matched a 4KB granule.
Note that the new default will prevent 4kB guest on 64kB host
because the granule will be set to 64kB which would be larger
than the guest page size. In that situation, the virtio-iommu
driver fails on viommu_domain_finalise() with
"granule 0x10000 larger than system page size 0x1000".
In that case the workaround is to request 4K granule.
The current limitation of global granule in the virtio-iommu
should be removed and turned into per domain granule. But
until we get this upgraded, this new default is probably
better because I don't think anyone is currently interested in
running a 4KB page size guest with virtio-iommu on a 64KB host.
However supporting 64kB guest on 64kB host with virtio-iommu and
VFIO looks a more important feature.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240307134445.92296-4-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows to choose which granule will be used by
default by the virtio-iommu. Current page size mask
default is qemu_target_page_mask so this translates
into a 4k granule on ARM and x86_64 where virtio-iommu
is supported.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240307134445.92296-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The acpi-generic-initiator object is added to allow a host device
to be linked with a NUMA node. Qemu use it to build the SRAT
Generic Initiator Affinity structure [1]. Add support for i386.
[1] ACPI Spec 6.3, Section 5.2.16.6
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ankit Agrawal <ankita@nvidia.com>
Message-Id: <20240308145525.10886-4-ankita@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI spec provides a scheme to associate "Generic Initiators" [1]
(e.g. heterogeneous processors and accelerators, GPUs, and I/O devices with
integrated compute or DMA engines GPUs) with Proximity Domains. This is
achieved using Generic Initiator Affinity Structure in SRAT. During bootup,
Linux kernel parse the ACPI SRAT to determine the PXM ids and create a NUMA
node for each unique PXM ID encountered. Qemu currently do not implement
these structures while building SRAT.
Add GI structures while building VM ACPI SRAT. The association between
device and node are stored using acpi-generic-initiator object. Lookup
presence of all such objects and use them to build these structures.
The structure needs a PCI device handle [2] that consists of the device BDF.
The vfio-pci device corresponding to the acpi-generic-initiator object is
located to determine the BDF.
[1] ACPI Spec 6.3, Section 5.2.16.6
[2] ACPI Spec 6.3, Table 5.80
Cc: Jonathan Cameron <qemu-devel@nongnu.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cedric Le Goater <clg@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ankit Agrawal <ankita@nvidia.com>
Message-Id: <20240308145525.10886-3-ankita@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NVIDIA GPU's support MIG (Mult-Instance GPUs) feature [1], which allows
partitioning of the GPU device resources (including device memory) into
several (upto 8) isolated instances. Each of the partitioned memory needs
a dedicated NUMA node to operate. The partitions are not fixed and they
can be created/deleted at runtime.
Unfortunately Linux OS does not provide a means to dynamically create/destroy
NUMA nodes and such feature implementation is not expected to be trivial. The
nodes that OS discovers at the boot time while parsing SRAT remains fixed. So
we utilize the Generic Initiator (GI) Affinity structures that allows
association between nodes and devices. Multiple GI structures per BDF is
possible, allowing creation of multiple nodes by exposing unique PXM in each
of these structures.
Implement the mechanism to build the GI affinity structures as Qemu currently
does not. Introduce a new acpi-generic-initiator object to allow host admin
link a device with an associated NUMA node. Qemu maintains this association
and use this object to build the requisite GI Affinity Structure.
When multiple NUMA nodes are associated with a device, it is required to
create those many number of acpi-generic-initiator objects, each representing
a unique device:node association.
Following is one of a decoded GI affinity structure in VM ACPI SRAT.
[0C8h 0200 1] Subtable Type : 05 [Generic Initiator Affinity]
[0C9h 0201 1] Length : 20
[0CAh 0202 1] Reserved1 : 00
[0CBh 0203 1] Device Handle Type : 01
[0CCh 0204 4] Proximity Domain : 00000007
[0D0h 0208 16] Device Handle : 00 00 20 00 00 00 00 00 00 00 00
00 00 00 00 00
[0E0h 0224 4] Flags (decoded below) : 00000001
Enabled : 1
[0E4h 0228 4] Reserved2 : 00000000
[0E8h 0232 1] Subtable Type : 05 [Generic Initiator Affinity]
[0E9h 0233 1] Length : 20
An admin can provide a range of acpi-generic-initiator objects, each
associating a device (by providing the id through pci-dev argument)
to the desired NUMA node (using the node argument). Currently, only PCI
device is supported.
For the grace hopper system, create a range of 8 nodes and associate that
with the device using the acpi-generic-initiator object. While a configuration
of less than 8 nodes per device is allowed, such configuration will prevent
utilization of the feature to the fullest. The following sample creates 8
nodes per PCI device for a VM with 2 PCI devices and link them to the
respecitve PCI device using acpi-generic-initiator objects:
-numa node,nodeid=2 -numa node,nodeid=3 -numa node,nodeid=4 \
-numa node,nodeid=5 -numa node,nodeid=6 -numa node,nodeid=7 \
-numa node,nodeid=8 -numa node,nodeid=9 \
-device vfio-pci-nohotplug,host=0009:01:00.0,bus=pcie.0,addr=04.0,rombar=0,id=dev0 \
-object acpi-generic-initiator,id=gi0,pci-dev=dev0,node=2 \
-object acpi-generic-initiator,id=gi1,pci-dev=dev0,node=3 \
-object acpi-generic-initiator,id=gi2,pci-dev=dev0,node=4 \
-object acpi-generic-initiator,id=gi3,pci-dev=dev0,node=5 \
-object acpi-generic-initiator,id=gi4,pci-dev=dev0,node=6 \
-object acpi-generic-initiator,id=gi5,pci-dev=dev0,node=7 \
-object acpi-generic-initiator,id=gi6,pci-dev=dev0,node=8 \
-object acpi-generic-initiator,id=gi7,pci-dev=dev0,node=9 \
-numa node,nodeid=10 -numa node,nodeid=11 -numa node,nodeid=12 \
-numa node,nodeid=13 -numa node,nodeid=14 -numa node,nodeid=15 \
-numa node,nodeid=16 -numa node,nodeid=17 \
-device vfio-pci-nohotplug,host=0009:01:01.0,bus=pcie.0,addr=05.0,rombar=0,id=dev1 \
-object acpi-generic-initiator,id=gi8,pci-dev=dev1,node=10 \
-object acpi-generic-initiator,id=gi9,pci-dev=dev1,node=11 \
-object acpi-generic-initiator,id=gi10,pci-dev=dev1,node=12 \
-object acpi-generic-initiator,id=gi11,pci-dev=dev1,node=13 \
-object acpi-generic-initiator,id=gi12,pci-dev=dev1,node=14 \
-object acpi-generic-initiator,id=gi13,pci-dev=dev1,node=15 \
-object acpi-generic-initiator,id=gi14,pci-dev=dev1,node=16 \
-object acpi-generic-initiator,id=gi15,pci-dev=dev1,node=17 \
Link: https://www.nvidia.com/en-in/technologies/multi-instance-gpu [1]
Cc: Jonathan Cameron <qemu-devel@nongnu.org>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Ankit Agrawal <ankita@nvidia.com>
Message-Id: <20240308145525.10886-2-ankita@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that pc_cmos_init() doesn't populate the X86MachineState::rtc attribute any
longer, its duties can be merged into pc_cmos_init_late() which is called within
machine_done notifier. This frees pc_piix and pc_q35 from explicit CMOS
initialization.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240303185332.1408-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The boot device order may change during the lifetime of a VM. Usually, the
"normal" order is set once during machine init(). However, if a user specifies
`-boot once=...`, the "normal" order is overwritten by the "once" order just
before machine_done, and a reset handler is registered which restores the
"normal" order during the next reset.
In the next patch, pc_cmos_init() will be inlined into pc_cmos_init_late() which
runs during machine_done. This means that the "once" boot order would be
overwritten again with the "normal" boot order -- which renders the user's
choice ineffective. Fix this by setting the "normal" boot order in
pc_basic_device_init() which already registers the boot_set() handler.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240303185332.1408-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The RTC can be accessed through the X86 machine instance, so rather than passing
the RTC it's possible to pass the machine state instead. This avoids
pc_boot_set() from having to access the current_machine global.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240303185332.1408-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Commit 99e1c1137b "hw/i386/pc: Populate RTC attribute directly" made linking
the "rtc_state" property unnecessary and removed it. Commit 84e945aad2 "vl,
pc: turn -no-fd-bootchk into a machine property" accidently reintroduced the
link. Remove it again since it is not needed.
Fixes: 84e945aad2 "vl, pc: turn -no-fd-bootchk into a machine property"
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240303185332.1408-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Specifying the property `-M pflash0` results in a regression:
qemu-system-x86_64: Property 'pc-q35-9.0-machine.pflash0' not found
Revert the change for now until a solution is found.
This reverts commit 6f6ad2b245.
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240226215909.30884-3-shentey@gmail.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 6f6ad2b245 "hw/i386/pc: Confine system flash handling to pc_sysfw"
causes a regression when specifying the property `-M pflash0` in the PCI PC
machines:
qemu-system-x86_64: Property 'pc-q35-9.0-machine.pflash0' not found
In order to revert the commit, the commit below must be reverted first.
This reverts commit cb05cc1602.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240226215909.30884-2-shentey@gmail.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since commit f10a570b093e6 ("KVM: x86: Add CONFIG_KVM_MAX_NR_VCPUS to allow up to 4096 vCPUs")
Linux kernel can support upto a maximum number of 4096 vcpus when MAXSMP is
enabled in the kernel. At present, QEMU has been tested to correctly boot a
linux guest with 4096 vcpus using the current edk2 upstream master branch that
has the fixes corresponding to the following two PRs:
https://github.com/tianocore/edk2/pull/5410https://github.com/tianocore/edk2/pull/5418
The changes merged into edk2 with the above PRs will be in the upcoming 2024-05
release. With current seabios firmware, it boots fine with 4096 vcpus already.
So bump up the value max_cpus to 4096 for q35 machines versions 9 and newer.
Q35 machines versions 8.2 and older continue to support 1024 maximum vcpus
as before for compatibility reasons.
If KVM is not able to support the specified number of vcpus, QEMU would
return the following error messages:
$ ./qemu-system-x86_64 -cpu host -accel kvm -machine q35 -smp 1728
qemu-system-x86_64: -accel kvm: warning: Number of SMP cpus requested (1728) exceeds the recommended cpus supported by KVM (12)
qemu-system-x86_64: -accel kvm: warning: Number of hotpluggable cpus requested (1728) exceeds the recommended cpus supported by KVM (12)
Number of SMP cpus requested (1728) exceeds the maximum cpus supported by KVM (1024)
Cc: Daniel P. Berrangé <berrange@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Julia Suvorova <jusual@redhat.com>
Cc: kraxel@redhat.com
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20240228143351.3967-1-anisinha@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Call pcie_sriov_pf_reset() from pci_do_device_reset() just as we do
for msi_reset() and msix_reset() to prevent duplicating code for each
SR-IOV PF.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-5-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
The spec does not NumVFs is reset after disabling VFs except when
resetting the PF. Clearing it is guest visible and out of spec, even
though Linux doesn't rely on this value being preserved, so we never
noticed.
Fixes: 7c0fa8dff8 ("pcie: Add support for Single Root I/O Virtualization (SR/IOV)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-4-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pcie_sriov_pf_disable_vfs() is called when resetting the PF, but it only
disables VFs and does not reset SR-IOV extended capability, leaking the
state and making the VF Enable register inconsistent with the actual
state.
Replace pcie_sriov_pf_disable_vfs() with pcie_sriov_pf_reset(), which
does not only disable VFs but also resets the capability.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-3-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
The guest may write NumVFs greater than TotalVFs and that can lead
to buffer overflow in VF implementations.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2024-26327
Fixes: 7c0fa8dff8 ("pcie: Add support for Single Root I/O Virtualization (SR/IOV)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-2-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@ericsson.com>
nvme_sriov_pre_write_ctrl() used to directly inspect SR-IOV
configurations to know the number of VFs being disabled due to SR-IOV
configuration writes, but the logic was flawed and resulted in
out-of-bound memory access.
It assumed PCI_SRIOV_NUM_VF always has the number of currently enabled
VFs, but it actually doesn't in the following cases:
- PCI_SRIOV_NUM_VF has been set but PCI_SRIOV_CTRL_VFE has never been.
- PCI_SRIOV_NUM_VF was written after PCI_SRIOV_CTRL_VFE was set.
- VFs were only partially enabled because of realization failure.
It is a responsibility of pcie_sriov to interpret SR-IOV configurations
and pcie_sriov does it correctly, so use pcie_sriov_num_vfs(), which it
provides, to get the number of enabled VFs before and after SR-IOV
configuration writes.
Cc: qemu-stable@nongnu.org
Fixes: CVE-2024-26328
Fixes: 11871f53ef ("hw/nvme: Add support for the Virtualization Management command")
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20240228-reuse-v8-1-282660281e60@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-3-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version 2.1+.
Signed-off-by: Felix Wu <flwu@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Message-Id: <20240221170027.1027325-2-nabihestefan@google.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
IOAPICCommonClass implements its own private realize(), and this private
realize() allows error.
Since IOAPICCommonClass.realize() returns void, to check the error,
dereference @errp with ERRP_GUARD().
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240223085653.1255438-8-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in iommufd_cdev_getfd(), @errp is dereferenced without ERRP_GUARD():
if (*errp) {
error_prepend(errp, VFIO_MSG_PREFIX, path);
}
Currently, since vfio_attach_device() - the caller of
iommufd_cdev_getfd() - is always called in DeviceClass.realize() context
and doesn't get the NULL @errp parameter, iommufd_cdev_getfd()
hasn't triggered the bug that dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
iommufd_cdev_getfd().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-7-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_usp_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_cap;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And since
cxl_usp_realize() - as a PCIDeviceClass.realize() method - doesn't get
the NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_usp_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-6-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in trng_prop_fault_event_set, @errp is dereferenced without
ERRP_GUARD():
visit_type_uint32(v, name, events, errp);
if (*errp) {
return;
}
Currently, since trng_prop_fault_event_set() doesn't get the NULL @errp
parameter as a "set" method of object property, it hasn't triggered the
bug that dereferencing the NULL @errp.
And since visit_type_uint32() returns bool, check the returned bool
directly instead of dereferencing @errp, then we needn't the add missing
ERRP_GUARD().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240223085653.1255438-5-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in ct3_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_free_special_ops;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And
ct3_realize() - as a PCIDeviceClass.realize() method - doesn't get the
NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
ct3_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-4-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in macfb_nubus_realize(), @errp is dereferenced without
ERRP_GUARD():
ndc->parent_realize(dev, errp);
if (*errp) {
return;
}
Here we check *errp, because the ndc->parent_realize(), as a
DeviceClass.realize() callback, returns void. And since
macfb_nubus_realize(), also as a DeviceClass.realize(), doesn't get the
NULL @errp parameter, it hasn't triggered the bug that dereferencing the
NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
macfb_nubus_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-3-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_fixed_memory_window_config(), @errp is dereferenced in 2
places without ERRP_GUARD():
fw->enc_int_ways = cxl_interleave_ways_enc(fw->num_targets, errp);
if (*errp) {
return;
}
and
fw->enc_int_gran =
cxl_interleave_granularity_enc(object->interleave_granularity,
errp);
if (*errp) {
return;
}
For the above 2 places, we check "*errp", because neither function
returns a suitable error code. And since machine_set_cfmw() - the caller
of cxl_fixed_memory_window_config() - doesn't get the NULL @errp
parameter as the "set" method of object property,
cxl_fixed_memory_window_config() hasn't triggered the bug that
dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_fixed_memory_window_config().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for VDPA network simulation devices.
The device is developed based on virtio-net and tap backend,
and supports hardware live migration function.
For more details, please refer to "docs/system/devices/vdpa-net.rst"
Signed-off-by: Hao Chen <chenh@yusur.tech>
Message-Id: <20240221073802.2888022-1-chenh@yusur.tech>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Shared objects lack spoofing protection.
For VHOST_USER_BACKEND_SHARED_OBJECT_REMOVE messages
received by the vhost-user interface, any backend was
allowed to remove entries from the shared table just
by knowing the UUID. Only the owner of the entry
shall be allowed to removed their resources
from the table.
To fix that, add a check for all
*SHARED_OBJECT_REMOVE messages received.
A vhost device can only remove TYPE_VHOST_DEV
entries that are owned by them, otherwise skip
the removal, and inform the device that the entry
has not been removed in the answer.
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20240219143423.272012-2-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The payload size returned by command VIRTIO_SND_R_PCM_INFO is
wrong. The code in process_cmd() assumes that all commands
return only a virtio_snd_hdr payload, but some commands like
VIRTIO_SND_R_PCM_INFO may return an additional payload.
Add a zero initialized payload_size variable to struct
virtio_snd_ctrl_command to allow for additional payloads.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20240218083351.8524-1-vr_qemu@t-online.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This CXL component isn't allowed to have a RAS capability.
Whilst this should be harmless as software is not expected to look
here, good to clean it up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240215155206.2736-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sometimes, certain parts are not being skipped in
vhost_vdpa_listener_region_del, but they are skipped in
vhost_vdpa_listener_region_add, or vice versa. The vhost-vdpa code
expects all parts to maintain their properties, so we're adding a trace
to help with debugging when any part is skipped.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20240215103616.330518-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next changes uses this variables, so avoid call repeatedly to memory
region functions. No functional change intended.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20240215103616.330518-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch extends the PCIe link speed option so that slots can be
configured as supporting 32GT/s (Gen5) or 64GT/s (Gen5) speeds.
This is as simple as setting the appropriate bit in LnkCap2 and
the appropriate value in LnkCap and LnkCtl2.
Signed-off-by: Lukas Stockner <lstockner@genesiscloud.com>
Message-Id: <20240215012326.3272366-1-lstockner@genesiscloud.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix an issue where cancellation of ongoing migration ends up
with no network connectivity.
When canceling migration, SVQ will be switched back to the
passthrough mode, but the right call fd is not programed to
the device and the svq's own call fd is still used. At the
point of this transitioning period, the shadow_vqs_enabled
hadn't been set back to false yet, causing the installation
of call fd inadvertently bypassed.
Message-Id: <1707910082-10243-13-git-send-email-si-wei.liu@oracle.com>
Fixes: a8ac88585d ("vhost: Add Shadow VirtQueue call forwarding capabilities")
Cc: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-8-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For better debuggability and observability.
Message-Id: <1707910082-10243-7-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Generalize duplicated condition check for the last vq of vdpa
device to a common function.
Message-Id: <1707910082-10243-4-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Prefer fast cpu_env() over slower CPU QOM cast macro
-----BEGIN PGP SIGNATURE-----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=NiP4
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-03-12' of https://gitlab.com/thuth/qemu into staging
* Add missing ERRP_GUARD() statements in functions that need it
* Prefer fast cpu_env() over slower CPU QOM cast macro
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmXwPhYRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWHvBAAgKx5LHFjz3xREVA+LkDTQ49mz0lK3s32
# SGvNlIHjiaDGVttVYhVC4sinBWUruG4Lyv/2QN72OJBzn6WUsEUQE3KPH1d7Y3/s
# wS9X7mj70n4kugWJqeIJP5AXSRasHmWoQ4QJLVQRJd6+Eb9jqwep0x7bYkI1de6D
# bL1Q7bIfkFeNQBXaiPWAm2i+hqmT4C1r8HEAGZIjAsMFrjy/hzBEjNV+pnh6ZSq9
# Vp8BsPWRfLU2XHm4WX0o8d89WUMAfUGbVkddEl/XjIHDrUD+Zbd1HAhLyfhsmrnE
# jXIwSzm+ML1KX4MoF5ilGtg8Oo0gQDEBy9/xck6G0HCm9lIoLKlgTxK9glr2vdT8
# yxZmrM9Hder7F9hKKxmb127xgU6AmL7rYmVqsoQMNAq22D6Xr4UDpgFRXNk2/wO6
# zZZBkfZ4H4MpZXbd/KJpXvYH5mQA4IpkOy8LJdE+dbcHX7Szy9ksZdPA+Z10hqqf
# zqS13qTs3abxymy2Q/tO3hPKSJCk1+vCGUkN60Wm+9VoLWGoU43qMc7gnY/pCS7m
# 0rFKtvfwFHhokX1orK0lP/ppVzPv/5oFIeK8YDY9if+N+dU2LCwVZHIuf2/VJPRq
# wmgH2vAn3JDoRKPxTGX9ly6AMxuZaeP92qBTOPap0gDhihYzIpaCq9ecEBoTakI7
# tdFhV0iRr08=
# =NiP4
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Mar 2024 11:35:50 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-03-12' of https://gitlab.com/thuth/qemu: (55 commits)
user: Prefer fast cpu_env() over slower CPU QOM cast macro
target/xtensa: Prefer fast cpu_env() over slower CPU QOM cast macro
target/tricore: Prefer fast cpu_env() over slower CPU QOM cast macro
target/sparc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/sh4: Prefer fast cpu_env() over slower CPU QOM cast macro
target/rx: Prefer fast cpu_env() over slower CPU QOM cast macro
target/ppc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/openrisc: Prefer fast cpu_env() over slower CPU QOM cast macro
target/nios2: Prefer fast cpu_env() over slower CPU QOM cast macro
target/mips: Prefer fast cpu_env() over slower CPU QOM cast macro
target/microblaze: Prefer fast cpu_env() over slower CPU QOM cast macro
target/m68k: Prefer fast cpu_env() over slower CPU QOM cast macro
target/loongarch: Prefer fast cpu_env() over slower CPU QOM cast macro
target/i386/hvf: Use CPUState typedef
target/hexagon: Prefer fast cpu_env() over slower CPU QOM cast macro
target/cris: Prefer fast cpu_env() over slower CPU QOM cast macro
target/avr: Prefer fast cpu_env() over slower CPU QOM cast macro
target/alpha: Prefer fast cpu_env() over slower CPU QOM cast macro
target: Replace CPU_GET_CLASS(cpu -> obj) in cpu_reset_hold() handler
bulk: Call in place single use cpu_env()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a SPAPR capability cap-nested-papr which enables nested PAPR
API for nested guests. This new API is to enable support for KVM on PowerVM
and the support in Linux kernel has already merged upstream.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The H_GUEST_RUN_VCPU hcall is used to start execution of a Guest VCPU.
The Hypervisor will update the state of the Guest VCPU based on the
input buffer, restore the saved Guest VCPU state, and start its
execution.
The Guest VCPU can stop running for numerous reasons including HCALLs,
hypervisor exceptions, or an outstanding Host Partition Interrupt.
The reason that the Guest VCPU stopped running is communicated through
R4 and the output buffer will be filled in with any relevant state.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
For nested PAPR API, we use SpaprMachineStateNestedGuest struct to store
partition table info, use the same in spapr_get_pate_nested() via
helper.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_GET_STATE which is used to get state of a nested guest or
a guest VCPU. The value field for each element in the request is
destination to be updated to reflect current state on success.
- H_GUEST_SET_STATE which is used to modify the state of a guest or
a guest VCPU. On success, guest (or its VCPU) state shall be
updated as per the value field for the requested element(s).
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Nested PAPR API provides a standard Guest State Buffer (GSB) format
with unique IDs for each guest state element for which get/set state is
supported by the API. Some of the elements are read-only and/or guest-wide.
Introducing additional required GSB elements and helper routines for state
exchange of each of the nested guest state elements for which get/set state
should be supported by the API.
[amachhiw: set the PCR whenever logical PVR is set]
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Currently, nested_ppc_state stores a certain set of registers and works
with nested_[load|save]_state() for state transfer as reqd for nested-hv API.
Extending these with additional registers state as reqd for nested PAPR API.
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcall H_GUEST_CREATE_VCPU which is used to
create and initialize the specified VCPU resource for the previously
created guest. Each guest can have multiple VCPUs upto max 2048.
All VCPUs for a guest gets deallocated on guest delete.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_CREATE which is used to create and allocate resources for
nested guest being created.
- H_GUEST_DELETE which is used to delete and deallocate resources
for the nested guest being deleted. It also supports deleting all nested
guests at once using a deleteAll flag.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Introduce the nested PAPR hcalls:
- H_GUEST_GET_CAPABILITIES which is used to query the capabilities
of the API and the L2 guests it provides.
- H_GUEST_SET_CAPABILITIES which is used to set the Guest API
capabilities that the Host Partition supports and may use.
[amachhiw: support for p9 compat mode and return register bug fixes]
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Amit Machhiwal <amachhiw@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
