Soren S. Jorvang <soren@t.dk>, with a lower match level.
Display the other accented characters which are not present in the IBM
character set by their non-accented equivalents, with an even lower
match level.
* Macroize hardware and software descriptor access (much easier to read).
* Simplify and optimize the transmit loop a bit, and use IFF_OACTIVE as
appropriate.
* Fix a potential race condition in the transmit loop. This change has
made the driver significantly more stable (almost completely eliminated
the "device timeout" errors that have plagued this driver).
* Implement transmit interrupt pacing.
* Add missing bus_dmamap_sync() calls (on transmit and receive descriptors
and fraglists). (Draining the write buffer when accessing these structures
may have also contributed to the increased stability of this driver on
the Alpha.)
Use fast memory timing NVRAM parameter. Clean up and fix establishment
of default target parameters. Don't use NVRAM if are flagged as not to
do so (I had a busted NVRAM setup which I couldn't edit that enabled SYNC
mode but disabled disconnect/reconnect and wide!!). Fix delays after
resets. BUS resets not done in isp_init anymore- relegated to OS
specific outer layers. Fix a buglet where you can get in a loop for
a NULL xs in the completion list in isp_intr. Add in some defines that
can disable fast posting. Add in code for Loop Up/Loop Down events that
call into the outer layers as to what to do.
define. Add a new config flag param (ISP_CFG_NONVRAM) whose intent it is
to cause NVRAM to be ignored. Add ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP
isp_async enums.
(we get LOOP DOWN events, and we'll hang on that at this time).
Add other isp_async cases- ISPASYNC_LOOP_DOWN and ISPASYNC_LOOP_UP. DOWN
will cause internal queuing until UP, whereupon a timeout will fire up
any pending xfers. It doesn't really keep commands from getting destroyed
by loop down events, but at least minimizes the damage. This was much
easier to implement with CAM.
the disk is ready to transfer data, and in ATA-5 the DSC has been obsoleted.
So only wait for DRQ to transfer data. This can be made conditional on the
ATA version if it's proven to break with some drives (worked with all the
drives I have access to).
While I'm there correct a few typos.
* Move the printf() delay to just after the printf(), where it actually makes
sense.
* Use zstty_stint() and zstty_softint() from zsparam(), to force an immediate
update of the carrier and flow control status. Abuse this in the attach and
open functions to defer all of that work. This insures that we don't lose
any status updates.
* Don't screw with register 1 when closing the console.
* Fix bugs in TIOCM??? (stay semicolon, clearing DTR while transmitting).
* Add comments in a couple of places.
the startup code. Implement a call to outer framework function so that
asynchronous events can be handled (e.g., speed negotiation, target mode).
Roll internal release tags.
Thanks to Scott for pointing this out to me (I got his mail and figured out
this change before seeing the discussion on tech-kern) and to Charles for
the initial explanation.
In wdc_probe_caps() add code to guess the ATA revision supported (if
ATA4 if Ultra-DMA, ATA2 if PIO mode > 2). We can't rely on param.atap_ata_major
here, at last one Ultra-DMA drive claims to support only ATA-3.
Use the ATA version in ata_perror(), and to try a flush cache command
in a shutdown hook for IDE drives.
calls
-support use of 2 fonts simultanously; this costs the ability to
"highlight", ie to use the upper 8 colours
-define screen types "80x25bf" and "80x50bf" which use this ability
-add conditional code to deal with the weird mapping of pcvt's
supplemental fonts
reported by Matthias Scheler <tron@lyssa.owl.de> in PR kern/6772.
- After receiving, check whether the receive DMA pointer became 0
what obviously happens if the list runs out of entries. Simply reinit
in this case. This fixes receive lockups after DDB use observed
by myself.
Unstall the receive engine if the ELINK_UPPKTSTATUS indicates that it
was stalled. (Don't know when this might happen. FreeBSD does so.)
+ Enable FIFO bursts, but also detect bogus 1040A with busted FIFO.
+ Use new MEMZERO crossplatform define.
+ Handle RQCS_QUEUE_FULL status case and let upper layer parse SCSI ststus
byte if nonzero (should be 0x28- Queue Full status)
+ Fold ISP_NVRAM_FIFO_THRESHOLD_128 into isp_fifo_threshold tag.
for FC HB based upon a SCCLUN define (15 for normal- 255 out of a possible
65535 for SCCLUN). Propagate loopid as adapter_target.
Roll minor platform version. Roll core version number.
Update mailbox definitions with cleaner target mode structure definitions.
Clean up some ENDIAN stuff. Correct botched ISP2100_NVRAM_HARDLOOPID offset.
- keep the modes supported by the drive in struct ata_drive_datas (will be
later used for downgrading the DMA/PIO mode on error)
- use config flags to force/disable PIO/DMA/UDMA modes
- For the CMD PCI0643/6 setup DMA mode to DMA Read multiple.
- When doing a first open, don't enable receive & status interupts before
the MD layer has had a chance to set things up.
- Enable logic to only enable DCD/CTS interupts if we are looking for/
expecting interupts on those pins. Disable otherwise.
- in zs_param, only pass up the state of ZSRR0_DCD if we have enabled
interupts on that pin.
Henry Hotz (<hotz@jpl.nasa.gov>) and Greg walsh <gwalsh@artec.com> have
tried these changes to get certain printers from hanging at boot. They
work in a 1.3.2 kernel for Greg.
an array of fixed-sized channel_softc elements. This way IDE controllers
which more than 1 channel (pciide) can extend the channel data easily
for private needs.
To avoid the double dereference at runtime, change the argument of
wdcstart() to the channel data pointer instead of the array index.
- Deactivate the card on removal and queue a REMOVAL event for the socket's
event thread to finish the detach.
- Queue an INSERTION event for the socket's event thread on insertion.
Implement a few missing infrastructure pieces to support this.
Hot swapping of PCMCIA cards now "works". (Not quite; things like network
devices need changes for their respestive subsystems. These changes are
coming soon...)
if the chip is reset while transmitting.
XXX
This occurs at boot time because the SIOCADDMULTI always resets the interface
when adding the `all hosts groups' -- usually while the ARP packet is being
transmitted. All drivers should be fixed to not reset the interface when
changing the multicast filter, if possible.
we can't use up all of the remaining sc->txslot[chan].bfree free
bytes) because that would cause the circular buffer read pointer
to become equal to the write pointer, thus signaling 'empty buffer'
to the hardware and stopping the transmitter. spotted and fixed
by Kenjiro Cho <kjc@csl.sony.co.jp>
in the printing of DMA mode (piix3/4 only)
others: set the debug_mask to 0, so that debug messages are turned off by
default but can be easily turned on.
Reset drive_flags to 0 for unconfigured devices, so that they are ignored
later. For configured devices, reset state to 0 after probe/attach.
struct scsipi_adapter; they were not used.
Add a scsipi_ioctl entry point to struct scsipi_adapter. This will be
used to issue ioctl commands to the host adapters.
Inspired by PR #6090, from Matt Jacob.
This bus space tag and handle is used for 32 bit data transfers i.e.
when WDC_CAPABILITY_DATA32 is enabled as the 32 bit data register may
not be part of the standard drive registers.
a slightly different fibre startup (print ALPA now too). Change
the way that return values from dma setup is done. Make debug messages
out of some queue overflow situations. Turn PORT LOGGED OUT into
Selection Timeout equivlaent. On isp_restart actions don't blow off
the commands with HBA_BOTCH (XS_DRIVER_STUFFUP) - set them with HBA_BUSRESET
(which is defined as XS_DRIVER_STUFFUP until someone decides whether
the suggested change to the midlayer NetBSD is worthy of inclusion).
thorpej