unnecessary, and given that there's no reason to waste time and
add complexity in trap handlers. This means that code which sets and
uses the USP has to be a bit more careful, but that doesn't happen much.
containing a substruct (the hardware frame) and an array of registers,
treat it like one big array of registers, for easier and prettier
access. Update everything to deal with that.
Process Control Block
Interrupt/Exception/Syscall Stack Frame
Machine Check Error Summary Register
Machine Check Logout Area
clean up some, and add prototypes for all of the CPU instruction and
PALcode function stubs.
- don't try and add a PDU trailer (or TBD for that matter) to an M_EXT
mbuf. when M_EXT is set, the data area of the mbuf can be shared
with other mbufs (see m_copym()), and writing to one M_EXT mbuf may
invalidate another M_EXT mbuf (saw this with PDU trailers).
- be sure to validate the length value from the PDU trailer so that it
doesn't throw us out of sync with the chip (fixes yet another source
of the dread "en_service: id mismatch" panic).
- on recv, don't bother allocating an mbuf if mlen is zero since we are
only going to toss the data anyway.
alpha_cpu.h, and this file is no longer necessary for the
Alpha. However, some machine-independent code (e.g.
/sys/compat/common/kern_exit_43.c) still wants a file with
this name to be around.
XID confusions with servers that cache them over a long period and
with clients that reboot quickly.
Problems: because of the sanity check that is done by comparing the system
time with filesystem time, XIDs will start at 0 until root is mounted,
which means it isn't completely safe for diskless setups. But it's clearly
better than it was. It would also be cleaner if all XID handling (more
generally, all RPC handling) within the kernel went through the
same functions.
matic media detection on Sun4m machines which support multiple media
(UTP and AUI). New function lenocarrier() switches media type when called
if no link? flags are set.
Redefine link flags for Lance ethernet (le):
<none>: switch between media as needed to find carrier (autodetect)
Preference to whatever the PROM is using (AUI if not booted
from the network)
link0: use UTP port only
link1: use AUI port only
This allows Sun4m machines with dual media Lance ethernet adapters to
boot from the network on the UTP port.
function is called when carrier is lost in lieu of a console message.
This is used by the sparc port to switch media types on Sun4m machines
if the appropriate link flags are set by ifconfig (see following commit
message). Should not affect ports that do not use sc_nocarrier().
we managed to kill the following SCSI-driver bugs for the Falcon:
- The Byte_Count_zero bit of the falcon DMA controller does not always
tell the truth! This caused the SCSI-driver to choke on devices that
disconnected in the middle of a DMA-transfer (mostly removables).
- Printing debug info about the 5380 on the Falcon is *only* permitted
when DMA is not active.
- Some functions forgot to remove possibly pending sofware interrupts
- Some debug options didn't allow debugging a single target while they
could easily be made to do so. This is fixed.
from the mach3 versions only as much as necessary to allow the old
NetBSD/Alpha pmap code to compile. THESE WILL NOT WORK AS-IS, and at
minimum will require code to implement reference- and modified-bit
emulation.
All Unibus dependencies are removed.
Can support different controllers on different buses.
Allows cloning of devices.
TODO:
Write support for MSCP tapes.
old config anymore, all devices should use new config by now.
Add structures to handle DMA devices using new config.
Fixed bug that caused unwanted ubareset's on 11/780.
Use new ldda() and stda() to make MultiCache initialization work on
SuperSparc-II machines (these machines require 64-bit access, even
to a 32-bit register).
existence of the SCSI hardware in the boards adress region.
Thanks to Oster Nerhus for the detailed bug report and to Ralph Schmidt for
the recommended probing method.
to ignore inbound data sizes less than the threshold. otherwise,
when connected to a video aal0 input the driver gives us a massive
stream of 56 byte mbufs each with one aal0 cell in it and the
system just can't keep up with it, especially if the socket buffer
size is large [it hangs until you turn off the video source].
fixes: when turning off a vc, try and check the freshest copy of the mode
when seeing if we need to enter the "drain" state. also, don't
panic if we get unexpected rx interrupt on a VCI (instead make sure
the VC is off, print a warning, and move on!).
- change rxso into a void handle ... no need to know details at this low
level.
fix:
- forgot to init "vci" during ENOTHER_DRAIN case of RX DMA interrupt
[could cause a vm_fault on native mode connection close depending
on needing to drain out the VC and also the random value of vci]
- more stat counters (rxmbufout -- mbufs, ttrash -- trashed RBD)
- add swsl_size to keep track of size of software slist
- revise when we call en_service
- fix handling of circular lists (was getting full vs empty confused in
extreem cases...)
- native mode atm: remove sbappend code: can't do it here since
socket buffer is protected only by splsoftnet and that doesn't
mask enintr off. forces us to switch to a two level interrupt
scheme. revise call to atm_input to reflect that.
- Good bye SYS_PBOOT and SYS_NBOOT, hello SYS_UBOOT (unified boot)
Currently supports booting from SCSI and HP-IB disk and network
from a single boot block. Infrastructure for booting from
HP-IB tape is there, but it doesn't quite work yet.
- Add a slightly modified version of Gordon Ross's "rawfs",
which provides a filesystem-like interface to tape devices.
Still needs debugging (see above).
- Rename sys_inst.c to inst.c, so that the LIF directory entry
turns out right (used to look like SYS_SYS_I if loaded from
tape).
- Add a "netio_ask" hint to netio.c, so that a special instnetio.o
doesn't have to be compiled for SYS_INST. Defaults to using
bootparams, but if set, will prompt user for information
usually obtained from bootparams.
- General cleanup.
in a more elegant way, but it works as is, and we need it now.
- Add a README and Makefile for the above. Note that this directory should
NOT be added to ../Makefile's SUBDIRS.
somehow got lost between NetBSD and Linux. Output side mbuf-walking
code now correctly bytestuffs mbuf chains, as well as single mbufs
and clusters.
* Update radio error-parsing code to Stuart's latest stable code.
We now parse error messages the older code didn't.
* Note where radio-crash watchdogs should be added (the linux code
is there, #ifdef'ed out). This still just doesn't work.
The radio reset doesn't always work even when slattatch is first started,
but I have a radio with old firmware, which may be a contributing factor.
* Correct the checks for the tty output queue being overfull; estimate
the stuffed pkt size as (original * 65/64) + STRIP_HDRLEN + 2,
instead of SLIP's (2*SLMTU). Re-enable the disabled check now the
size estimate isn't excessively large.
* Fix BPF tapping of strip interfaces, STRIP packets are wrapped
in a SLIP bpf header. This implies no BPF support for arp or atalk,
even though Linux boxes are sending arp requests and gratuitous arps.
There may be no good fix short of adding explicit STRIP encapsulation
support to bpf/tcpdump.
* Still need a solid walkthrough, and rewrite to eliminate redundant
receive-side mbuf copying.
[1] if user tries to enter in a bogus PVC don't leave it in the routing
table ... remove it
[2] change ioctl arg to include rxso for lower layer
[3] add hooks (inside "NATM" ifdef) for native mode atm sockets so that
they don't clash with IP PVCs. [i am still debugging the native
mode atm socket protosw code]
[1] rxslot "cur" pointer wasn't updated if we copied all data and
didn't have any fill. this could cause a service id mismatch
panic under load.
[2] recv of aal0 forgot to include the cell header in the data length
calc [add cell header length to midwayreg.h]
[3] fix control info "chop" for raw mode and aal0
[4] handle rxsb better for native atm connections
(XXX: still working on this ... not complete and needs revision)
- ability to be either a BROADCAST or POINTTOPOINT interface.
- a humble beginning of link-layer addressing (differs from PR
by using a `struct sockaddr' instead of single byte).
- Use an extent map to manage the ISA memory "hole", much like
how i/o port space is manged with an extent map. Do the actual
accounting in bus_mem_{,un}map().
- When creating the ioport and iomem extent maps, pass the
EX_NOBLOB flag, which tells the extent map code to disallow
fragmenting of regions. This will make it easier to catch
simple i/o and memory mapping bugs (like the if_ed.c bug I just
fixed) in the future.
- In bus_mem_map(), a chunk of code was indented using spaces.
Make the indentation use tabs.
- In bus_io_unmap(), fix the format passed to printf().
physical memory is sized by a loop that writes data to the first
word in a page, (writes something else to settle the bus) and then reads
back the word it wrote. If the read succeeds, the amount of physical
memory is increased by one page.
This fails on a 5000/1xx with a memory subsystem filled with 8 low-density
(4Mbyte) SIMMs. The memory-decoding hardware aliases the 32Mbytes of
physical memory at physical addresses 0, and at 32M (and presumably
at 64 and 96Mbytes.) The contiguous aliasing causes the memory-sizing
loop to continue at 32 MBytes, testing the memory that's really
at address 0, overwriting and crashing the kernel.
Fixed (for 1.2) by reading the SIMM-decoder stride size from the
motherboard, and reducing the loop bound to 32Mbytes on a 5000/1xx
with low-density SIMMs. (Other models have a non-power-of-2 maximum
memory and so are not subject to _contigous_ aliasing of physical memory).
This takes care of two related problems:
- `umount -f' wouldn't work if someone's working directory is
the filesystem root.
- vfs_unmountall() would complain about a busy `/' on a
diskless setup.
The physical memory-sizer claims to preserve memory contents
(specifically the contents of msgbuf). The loop writes different
values into two adjacent locations and reads the contents of the
first, to ensure that whatever is read back from the first location is
from memory and isn't just the first write persisting on the bus.
The loop preserved the value of the first location, but not the second,
resulting in the second test value ('ZZZZ') over-writing a word in msgbuf.
- A fixed extent map (statically allocated descriptor storage) is
created in init386(), just before the call to consinit(). The
fixed descriptor storage has enough room for 8 region entires,
which is plenty for early initialization, but doesn't chew up
that much memory.
This extent map (ioport_ex) manages the i386 i/o port
space (0x0 - 0xffff).
- Just before the call to configure() in cpu_startup(), a
flag is set which notifies the bus_io functions that it is
safe to use malloc() to allocate descriptor storage, in the
event that more than 8 regions are needed.
- bus_io_map() attempts to allocate the specified region from
ioport_ex. If the allocation succeeds, the io handle is
filled in. If the allocation fails, it is implied that
something else is already using that io space, and an
error condition is returned.
- bus_io_unmap() frees a region previously allocated from
ioport_ex in bus_io_map(). If the free fails, a warning
is printed on the conole.
These changes implement "port accounting". This is required for
proper autoconfiguration on the i386 port, and makes dealing with,
among other things, PCMCIA io mappings _much_ easier.
Understands allocation aligment and boundary restrictions, "specific region"
allocations, and suballocations. Capable of statically or dynamically
allocating map overhead.
Many thanks to Matthias Drochner for running the code for me, and sending
me bug fixes, optimizations, and suggestions. Also, many thanks to
Chris Demetriou for his extremely helpful suggestions.
XXX No manual page yet. One is forthcoming, as soon as I can scare up
the time to write one. This has been sitting on my plate for quite a
while, and several projects are waiting for it. Time to move on.
piece of hardware into kernel virtual memory (was only a guess 'til now).
XXX Unfortunately, the hardware vendor reserves the right to change this in
future DraCo revisions. We must rethink delay() and DELAY(), at least for the
DraCo, soon.
which was taken from OpenBSD/pica.
The previous revision of elf.c replaced Ted Lemon's elf exec machinery
with something closer to Christos' MI elf machinery. It turns out
that old NetBSD/pmax elf binaries have three segments, and the newer
elf exec machinery cannot exec them.
The old elf exec machinery is folded back into cpu_exec.c, which falls
back onto using the old machinery if the new machinery fails. The
old-style binaries will be deprecated at the 1.2 release.
is close to how I reworked it, I pulled in the (essentially MI) NetBSD/alpha
and added the appropriate support around it.
- No need for the GENERIC kernel config option.
- NFS-mounted root and swap are supported.
- If we can't figure out where the root filesystem is from what the Booter
tells us, ask the user.
- Split the mainbus autoconfig code to a separate file.
Also, update/add copyrights as appropriate.
delayed write is logically converted to a sync write, mirroring the async case.
In bdwrite(), move the tape case earlier to avoid needless reassignbuf()s.
where the console is, because that is correct if, for example, you
boot with the diag/norm switch set for diagnostics and the EEPROM
is set for keyboard/display.
* Update arch/mips/mips/cpu_exec.c to include MI exec_elf.h header,
and to use the MI interface exec_elf_makecmds().
* Replace arch/mips/mips/elf.c (Ted Lemon's elf code) with
a version of Christos's MI elf exec code, munged to support demand paging
and mips shared libraries.
Show proper inquiry data when version >= 1, not <= 1 (SCSI-2 devices
now display their inquiry infor).
Correct transfer length passed to dk_unbusy (b_resid hasn't been
updated yet).
* Eliminate the #ifdef DS5000 and kernel config option DS5000 altogether.
option DS5000 was a hangover from 4.4bsd/pmax; it's never been clear
if it means "support for DS5000/200" or "support for any TC machine".
This implictly fixes pr 1828.
* Use the "tc.h" and NTC generated by config for a "tc? at mainbus"
where appropriate, intsead of #ifdef DS5000.
* Canonicalize the spelling of kernel options that enable support
for particular models. Use
DS5000_25 for the Personal Decstation aka MAXINE aka KN02-ca
DS5000_100 for the 5000/1xx series aka KMIN aka KN02-ba
DS5000_200 for the 5000/200 aka 3MAX aka KN02
DS500_240 for the 5000/240 aka 3MAXPLUS aka KN03
and change DS_5000_xxx to DS5000_xxx everywhere.
* Wrap the interrupt handlers for each model in the appropriate #ifdef,
instead of wrapping all of them with "#ifdef DS5000".
* Wrap the TC autoconfig for each model in the appropriate #ifdef.
* Eliminate the #ifdef DS5000 and kernel config option DS5000 altogether.
option DS5000 was a hangover from 4.4bsd/pmax; it's never been clear
if it means "support for DS5000/200" or "support for any TC machine".
This implictly fixes pr 1828.
* Use the "tc.h" and NTC generated by config for a "tc? at mainbus"
where appropriate, intsead of #ifdef DS5000.
* Canonicalize the spelling of kernel options that enable support
for particular models. Use
DS5000_25 for the Personal Decstation aka MAXINE aka KN02-ca
DS5000_100 for the 5000/1xx series aka KMIN aka KN02-ba
DS5000_200 for the 5000/200 aka 3MAX aka KN02
DS500_240 for the 5000/240 aka 3MAXPLUS aka KN03
and change DS_5000_xxx to DS5000_xxx everywhere.
* Wrap the interrupt handlers for each model in the appropriate #ifdef,
instead of wrapping all of them with "#ifdef DS5000".
#define so that ifr_mtu accesses that. MTU shouldn't be overloaded
with ifr_metric, if only for clarity. Adding an MTU field to the
union hurts nothing (in fact, does not actually _change_ generated
code), and does improve clarity.
works) for my machines and now-nonexistent test machines. Clean up
options in existing config files so that they're more consistent. Add
more units of various pseudo-devices to several.
For these CPU's, you have to use the ptest operation to search the mmu
tables in order to decide whether it is a real bus error or just a
page fault or write protection violation.
Our old code assumed user space always when calling ptest, and
erroneously assumed the BUSERR bit in the ptest output (mmusr
register) is the only indication for bus errors to check.
In fact, we have to follow a multistage decision tree to decide. 68060
CPUs are much easier to handle correctly.
Since linux binaries are (mostly) always compiled with gcc, look for
the gcc signature in the .comment section header: "\0 GCC: (GNU) ".
I've changed the probe order in kern/exec_elf.c to probe for linux ELF
binaries first and fall back to SVR4 binaries. This makes statically
linked binaries work for both linux and svr4. Note that gcc-compiled
svr4 binaries, still contain the operating system signature first and
then the GCC signature, so there is no conflict. Yes this is a hack.
and free some space by calling m_reclaim(). Also, log the "mb_map full"
error message (at most) every 60-seconds. The old code would log it
once over the lifetime of the system, but that's not a useful diagnostic.
(More useful is the new behaviour, which roughly indicates how often
periods of heavy load occur, without spamming the console and system
logs with messages.)
Right now, this code just panic()s (same as kmem_malloc() used to do
before, but different message), but in the future it should be modified
to try to reclaim wasted memory.
automatic array rather than an array allocated with alloca().
(This was the only use of alloca() in the kernel, and it wasn't
necessary or consistent with the way other functions in this file
work.)
This is a bit of a hack, as-is, since there's a lot of code that's
outright duplicated between the various files and because it doesn't
support detection of a network device as the root device. The
latter's not a problem yet, because NetBSD/Alpha can't load the kernel
from the network to begin with.
structure and 'aux', right before ca_attach is called for the
newly-attached device. This allows the alpha port to do root device
autodetection without modifying every bus and device driver which could
be in the 'boot path.' In the long run, it may make sense to make
this machine-independent.
an extended header is present i.e. don't assume an extended header as
however unlikely there could be a podule that doesn't have one.
Calculate an absolute address for the podule's interrupt mask rather
than leaving it relative to the base address of the podule.
If the interrupt status pointers are not present or are zero then
used the default bits as specified in the podule specification to
determine if the podule is interrupting.
chained podule interrupt handlers.
Fill out the ih_maskaddr and ih_maskbits fields in the interrupt handler
structure so that interrupt dispatcher knows where to look to determine
if the handler should be called.
General code tidy up and source code formatting.
chained podule interrupt handlers.
Fill out the ih_maskaddr and ih_maskbits fields in the interrupt handler
structure so that interrupt dispatcher knows where to look to determine
if the handler should be called.
back on timer 1 interrupts if none is specified.
Only set up timer 1 is the driver is using timer 1 interrupts.
Don't claim the interrupt but allow them to be passed on to other
handlers.
Fixed the handling of IPL_NONE.
Debugged support for interrupt chaining.
Fill out the intrnames array with the name of the interrupt handler
currently at the head of the chain.
Guarded several sanity checks with #ifdef DIAGNOSTIC.
Added interrupt chaining.
Removed some dead debugging code.
Guarded several sanity checks with #ifdef DIAGNOSTIC
Make sure interrupts are disable while updating the IOMD interrupt
masks.
Removed several old debugging functions that are no longer needed.
Block interrupts while updating the soft interrupt masks.
Fixed softclock interrupts and added IRQ_SOFTPLIP to the SPL_SOFT mask.
Rename the currently unused irq handler structure fields for podule
interrupts so they make more sense.
Define IPL_NONE as a positive value instead of -1 and increase the
number of IPL levels.
from from the corresponding `ic_*' and `dc_*' values. This is not perfect,
but it makes SS4s and SS5s run until we have proper per-cpu cache handling.
Use the `cache-physical?' property to determine the value of `vactype'
on sun4m's. If absent, set vactype to VAC_WRITETHROUGH (XXX) else VAC_NONE.
Print simpler sun4m CPU identifier on attach.
>use p->hashfraction when doing non-time-critical calculations, rather than
>using HASHFRACTION directly. in time-critical calculations, if HASHFRACTION
>is a power of two, check that p->hashfraction == HASHFRACTION and if so do
>the calculation with the compiled-in value so that the compiler can optimize
>out (potentially) expensive divisions. if p->hashfraction != HASHFRACTION,
>actually do the division. This has the result that on machines with slow
>division, the division can be optimized out of the common case, but that
>if HASHFRACTION changes from the compiled-in value (for whatever reason),
>profiling will still work. Changes suggested by Chris Torek.
(1) right now GENERIC can boot via NFS, and
(2) in the long run, GENERIC should autodetect network booting
and pick the correct root device.
Because of (1), GENERIC_NFS is no longer _needed_ in the short term.
Because of (2), GENERIC_NFS is not _wanted_ in the long term.
and whacking a bit here and there where appropriate. Does not yet do
automatic root device detection, but that's much easier to add now.
RB_ASKNAME now supports specification of network devices, for diskless
booting. Also, RB_ASKNAME is now supported on _all_ kernels.
a (was ~RB_SINGLE, redundant with 'A') -> askname
n (was RB_ASKNAME) -> no meaning
d (was RB_DFLTROOT) -> no meaning (unnecessary with new setroot() code)
m (was RB_MINIROOT) -> no meaning (miniroots currently unsupported;
#ifdef'd out)
N (was ~RB_ASKNAME) -> no meaning (unnecessary; just don't specify RB_ASKNAME!)
Enable reselections as soon as possible after a disconnect - prevents
losing a reselecting device.
Check for and ignore a spurious interrupt during a DMA input (from the
Mach driver).
>Update for present reality (function names), clean up a bit (printfs,
>"panic: foo XXX"), and fix a couple of printf format specified bugs
>(which were normally #if 0'd out). Inspired by Multia/UDB support
>changes sent by Matt Thomas.
and:
>changes from Matt Thomas so that the Multia/UDB can attach its
>'com' interrupts, cleaned up some. Basically: if sharing type of
>new interrupt is different than what the hardware is currently set up
>for (e.g. requesting edge-triggered and the hardware is set up by
>the PROM for level triggered) and there are no interrupt handlers on
>that line already, warn about it and use the hardware type that the
>line was already set for (to avoid making the console blow up on
>reboot). If same circumstances but there is already a handler, panic
>as before.
Turbochannel as well as the IOASIC. It should now work on the 5000/200.
Removed the "aborts" which could leave the disk trashed when the abort
rebooted the system. Fix the data corruption problem by clearing the
FIFO before starting a data transfer.
common back-ends that live on multiple very-different busses (e.g. PCI and
TC), which need bus-specific DMA mapping support. As a nice side effect,
this will allow the especially nasty (vtophys(va) | 0x40000000) expressions
to go away in favor of less nasty bus-specific function calls.
clear which switches the video signal on and which off.
Make all grf_??.c (which supported it) use the same polarity of the test.
While being here, use a > test instead of implicit != to make it extensible
to darker than dark values for power managment systems.
as the Fastlane Z3, but is different enough to let the kernel crash.
Closes PR #2492 by Matthias Scheler. [thanks also to Ralph Schmidt for
confirmation of the patch]
