isascan (__BROKEN_INDIRECT_CONFIG), and attempt multiple match/attach
of cloning devices in isasearch(). (If a match/attach succeeds for
a cloning device, try it again.)
- fix the parser so that non-compliant isapnp devices work, and we
give up when there are too many errors (some on-board pnp sound/atapi/game
soundblaster compatible card). reported by chuck cranor
- fix the parser so that configuration tags that come after the
end-dependencies tag or before the begin-dependencies tag are merged
in properly (gravis ultrasound). reported by gary duzan
We now build a tree of card -> logical-dev -> conf, and in the end we
convert it to a list of conf...
- if aal5 frame has a CRC error then the length field in the aal5 trailer
may not be valid, so we can not use it [and we must dump the frame]
[Yuhang Sun <sunyh@dworkin.wustl.edu> & chuck@ccrc.wustl.edu]
Dave Huang <khym@bga.com>
Tested on alpha by cgd, tested on several i386 boxes. Certainly causes
no harm to the goddamned mess, but the NCR driver only works when you
perform voodoo rituals on it anyway.
This is what Dave said (in email) has been added to the driver:
----------------------------------------------------------------------
This seems to be the most significant change:
General cleanup and new features for 53c875 based cards, especially the
Tekram DC390W/U/F, whose config EEPROM can now be dumped, if the kernel
is built with option NCR_TEKRAM_EEPROM.
Other changes:
- add brackets to expansion of OUTB/W/L macro arguments.
- remove unused NCB structure element ns_async
- support sync. SCSI offset of 16 (instead of only 8) on 825A and 875
- correctly identify 53c810A and 53c825A chips
- preserve SCSI BIOS settings of PCI performance options
- remove (already disabled) support for NCR reset because of command timeout
- reverse order of reading of SCSI and DMA specific interrupt cause registers
- add definition of Tekram config EEPROM contents (not currently used)
----------------------------------------------------------------------
Newer boards (e.g., Vortex) take time to reset, and wedge on some machines.
Polling on S_COMMAND_IN_PROGRESS would be better, but that doesn't
work with xx_RESET commands on 3c509s.
CONFIG_CNTRL bits by making the "conn" argument to epconfig()
a u_int, not a u_int16_t, and by defining 100mbit media
bits in the upper 16 bits.
A redesigned interface that fixes this properly is in the pipeline.
comments in pr port-i386/2358: "if_ep/3C590 no longer working"
* Only call Vortex media-config code on PCI-attached devices, until
we know if it works on ISA and EISA large-packet devices also.
* Fix typo in printf of MAC address
rather than unknown.
* Look for 100mbit interfaces, and for any present, set corresponding
bits in `conn' argument to epconfig(). epconfig() will now print
100Mbit media by name.
look for 100mbit Xcvrs, print their names, add to ep_connectors.
* Print 10baseT as 10baseT, since media name (utp) is no longer a unique
transceiver type.
* Redo FIFO memory size printing, also show Tx/Rx split (xxx isa 3c509?).
* Print MAC address on a separate line, with 100Mbit media and fifo-ram
info it no longer fits on the same line as media types.
* Comment the fact that the "connection" media-selection code just doesn't
grok 100Mbit media.
* add code to look for 3c59x/3c90x media-select and autoconfig bits, though
we don't yet dynamically probe media when the autoconfig bit is set
(see previous bullet).
* XXX the whole connector/media code should be redone, perhaps a' la
the BSDI ifmedia design.
For now, we really only need 8 bits of media type.
* Add bogus definitions for 100mbit transcievers, to be set in the
"conn" argument to ep_config(). Should really use the same bits
as in EP_W0_CONFIG_CTRL bits, but I don't know what bits the 3c515
&c use for 100mbit media.
* Define bitflags for 100Mbit transceiver options in ep_connectors.
* Add definitions of powerup/powerdown commands. for interfaces with
power management. Should send a powerup after APM resume?
* Add definition of fragment-busmaster (vortex) START_DMA command.
* Add definition of PCI configuration-space media-present bits.
(really just EP_W3_RESET_OPTIONS remapped into pci config space.)
* Add comments describing what the #define's above are used for.
For now, we really only need 8 bits of media type.
* Add bogus definitions for 100mbit transcievers, to be set in the
"conn" argument to ep_config(). Should really use the same bits
as in EP_W0_CONFIG_CTRL bits, but I don't know what bits the 3c515
&c use for 100mbit media.
* Define bitflags for 100Mbit transceiver options in ep_connectors.
* Add definitions of powerup/powerdown commands. for interfaces with
power management. Should send a powerup after APM resume?
* Add definition of fragment-busmaster (vortex) START_DMA command.
* Add definition of PCI configuration-space media-present bits.
(really just EP_W3_RESET_OPTIONS remapped into pci config space.)
* Add comments describing what the #define's above are used for.
bit from the extended setup inquiry and key off it to:
- Force synchronous negotiation on targs > 7.
- Read additional information returned by wide cards on inquire setup.
- Read sync period on targs > 7.
- Display sync period/offset on targs > 7.
- Set scsi_link.max_target to 15.
cvs: ----------------------------------------------------------------------
host adapter drivers, indicating the highest SCSI target they can
address. Use this value to dynamically allocate data structures, rather
than hard-coding 8 targets.
These changes allow targets > 7 to be addressed on wide SCSI busses.
Fixes PRs #1674 and #2892.
Add newline to `Interface disabled' printf and clean up formatting.
Change packet read/write code to align all reads and writes into
memory to an appropriate boundary for the I/O size. This also fixes
a bug where the trailing unaligned bytes (1-3 of them) would be
put in an additional mbuf even if there was enough space for them
in the one we were currently filling.
This has been tested on a 3c905 in an Alpha (32-bit I/O, alignment
required), a 3c905 in an i386 (32-bit I/O, alignment not required)
and a 3c509 in an i386 (16-bit I/O, alignment not required). It
should be tested on a 3c509 in an Alpha with an ISA bus, if somone
can manage to get the two items together.
There are still some bugs in the driver relating to initialisation;
on my Alpha with a 3c905 you need to do an `ifconfig ep0 down;
ifconfig ep0 up' after the initial ifconfig to make it start working.
Apparently there are also some problems with a 3c579 in an i386,
although a 3c905 in an i386 works just fine.
(e.g. from 0x3bc to 0x3bf, for example). Others may require more,
but until there's some special handling for them, 4 should be returned
so that on systems with I/O port accounting, the unit at 0x3bf can be
properly mapped, etc. (OK'd by mycroft.)
that their child busses can be attached after the PCI bus
autoconfiguration for their parent bus is done.
This works because:
(1) there can be at most one ISA/EISA bridge per PCI bus, and
(2) any ISA/EISA bridges must be attached to primary PCI
busses (i.e. bus zero).
That boils down to: there can only be one of these outstanding
at a time, it is cleared when configuring PCI bus 0 before any
subdevices have been found, and it is run after all subdevices
of PCI bus 0 have been found.
This (or something like it) is needed because there are some (legacy)
PCI devices which can show up as ISA/EISA devices as well (the prime
example of which are VGA controllers). If you attach ISA from a
PCI-ISA/EISA bridge, and the bridge is seen before the video board is,
the board can show up as an ISA device, and that can (bogusly)
complicate the PCI device's attach code, or make the PCI device not be
properly attached at all.
This could be done with machine-dependent code, but as more ports
add support for PCI (and PCI-ISA/EISA bridges) more will need it.
The i386 port could (perhaps should) be converted to use it as well.
devices actually do make sense on indirect-config busses, because you
might be able to have more than one of the busses! In addition, they're
useful because they don't require unit numbers to be wired down, so you
could e.g. have vga* at indirect? and vga* at direct?, and have the first
one found be unit number zero. Finally, devices which can divine their
own ports numbers, etc., actually should be cloning, even if you know you'll
only have one bus that they can live on.
1. fix possible hang in en_txlaunch(). when attempting to extend
the length of an mbuf to avoid a flush we should extend it
by cnt [which is ((need - len) % 4)] rather than 4 - cnt.
also, add an EN_DEBUG printf() when we pad/FLUSH a buffer
to help with debugging/understanding what the driver is up to.
2. use interface packet counters
3. when turning off a recv VCI we recompute the new mode. make sure
we don't include the "in service" bit in the new mode, otherwise
a VCI may appear "hung" if you turn it off while a service
interrupt is pending.
4. when shutting down a VCI that is still receiving data, don't bother
going into "drain mode" if only the hardware in service bit is
set (otherwise the VCI may get "hung" in drain mode).
as a result of this we may get "unexpected rx interrupt" messages
which are not really an error, so put this printf in EN_DEBUG.
5. be sure to zero txspeed[lcv] when enabling a VCI (start at full
speed). (hooks for setting txspeed[] are currently not in
the driver, but we are playing with it locally).
credits:
#1: Detected by: Zdenek Salvet <salvet@horn.ics.muni.cz>, fix by me.
#2: Contributed by: Zdenek Salvet <salvet@horn.ics.muni.cz>
#3,#4,#5: Detected by: Milind M. Buddhikot <milind@dworkin.wustl.edu>,
fixed by me.
2841, plus some fixes to make the patches work on the Alpha. Seems to
improve the NCR driver a lot. We probably should try to incorporate
any updates that have happened since, too.
* Add a slot in the softc, ep_pktlenshift, to indicate that
a board implements ``large packets'' (FDDI-sized frames) and
therefore implicitly shifts the argument to packet-length commands
by two bits to fit a 13-bit length in an 11-bit command argument field.
* Change the reset of station-mask filterto be independent of bus-type
(e.g.,. for 3c515)
* Replace the "2044" constant used to disable TX threshold interrupts
on 3c509-generation cards with a #define. Use 2047 instead,
since that works on the large-packet cards (Vortex, Demon, Boomerang)
and 2044 doesn't.
* Add code to epconfing to probe for large-packet support,
set the softc appropriately, and shift packet sizes in commands
by ep_pktlenshift to compensate for the implicit shift.
* Tweak the epconfig() code to avoid hanging on startup.
Set the Tx threshold to interrupt when there's space for
a maximal-sized ether frame, then do epinit() then epstop(),
instead of just the Tx and Rx reset. Required on at least a 3c595.
Tested on a 3c595, but not on 3c509-generation hardware.
(This fixes problems with the printf format fixes i checked in yesterday.
ptrdiff_t is an 'int' on the i386 but a 'long' on the alpha, so the cast
really is necessary... *sigh*)
ISA-compatible port space of PCI buslogic cards.
* Add call to bha_pci.c to disable the ISA-compatible ports of a PCI
device. The ISA-compatible ports are enabled by default, which
causes the card to be autoconfigured a second time as an ISA device,
which appears to deadlock the card.
* Change bha_cmd() to return the number of bytes it actually received
in response to a command, or -1 on error.
* Use heuristics (checking for bha-only registers, and checking the size
of the response to BHA_INQURE_EXTENDED) to bha_find, to make sure the
bha driver never matches an aha (Adaptec 1542 or compatible) device.
A single kernel should now boot on either Adaptec or BusLogic controllers,
provided we always probe for BusLogic devices before Adaptec devices,
but this has not yet been verified.
management by itself. But when it gets a start unit request, it keeps
the floppy motor running all the time. This adds code for dealing with
yet another quirk (SDEV_NOSTARTUNIT) that prevents sd.c from sending
start unit requests. A entry for the Teac FC-1 is added to the quirk
table.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
- No more distinction between i/o-mapped and memory-mapped
devices. It's all "bus space" now, and space tags
differentiate the space with finer grain than the
bus chipset tag.
- Add memory barrier methods.
- Implement space alloc/free methods.
- Implement region read/write methods (like memcpy to/from
bus space).
This interface provides a better abstraction for dealing with
machine-independent chipset drivers.
prototypes, and suppress a bogus "might be used uninitialized" warning.
It's clear from reading the logic of the function that produces the
warning that the variable will not be used uninitialized, but the
compiler just isn't smart enough, I guess. Marked XXX for future reference.
restart if we get multiple status interrupts before the softintr()
routine gets a chance to run. The fix is to determine and accumulate
status line changes at the H/W interrupt level, and then check and zero
the accumulated changes when the softint() finally runs. Many thanks
to Bill Studenmund <wrstuden@loki.stanford.edu> for finding and fixing.
dev/microcode/aic7xxx_seq.h,
dev/ic/aic7xxxreg.h:
Remove intrinsic knowledge about SDTR and WDTR messages and replace it
with a generic message system that allows the kernel driver to handle
SDTR, WDTR and any other type of extended message it chooses too. This
makes the sequencer code much simpler, makes extended message handling
debuggable since the bulk of the work is in the kernel driver, and saves
lots of instruction space.
Regen microcode header file.
dev/ic/aic7xxx.c, dev/ic/aic7xxxvar.h:
Add code to handle WDTR and SDTR negotiation in light of the changes in
the message interface to the sequencer. Don't reject targets that
negotiate async by sending an SDTR with a 0 offset. Use an sdtr message
with 0,0 to negotiate async when a target suggests a period that is too
long for us to handle. Some tape and cdrom drives don't like us doing
the message reject that we did in the past.
Fix a problem with handing the QUEUE FULL condition.
Fix a race condition (most likely the cause of the SCB paging problems) that
might allow the sequencer to get unpaused before the condition that caused
it to be paused (a SEQINT) was handled.
Race condition pointed out by Doug Ledford <dledford@dialnet.net> and
by "Dan Willis" <dan@plutotech.com>.
dev/pci/ahc_pci.c:
Add support for the 2940AU, an aic7860 based controller.
dev/pci/pcidevs.h, dev/pci/pcidevs_data.h:
Add product IDs for the 2940AU, aic7860 and aic7855.
Regen data file.
scsi/scsi_message.h:
Add MSG_EXT_SDTR_LEN and MSG_EXT_WDTR_LEN - the length of bytes in these
extended messages.
Thanks to Chuck Cranor <chuck@maria.wustl.edu> for testing these changes
out for me.
* When we are transferring in DATA (in asc_dma_in) and the target
is an async device, there is sometimes an extra byte in the FIFO.
If so, we need to drain that byte out of the fifo, but if and only
if the target is async. See also the comments in asc_dma_in()
in the related Mach mk84 asc driver (scsi_53C94_hdw.c), which
has an identical fix but applied in more restrictive conditions
than we need, with async *disk* targets, as well as async tapes.
* Add a watchdog and timeout active SCSI requests, to eliminate any
potential for deadlock due to applying the fix above on newer
silicon versions of the 53c94 which may not have the above problem.
Should use the MI scsi per-target timeout instead, when available.
cfattach code for TC SCSI option cards and ioasic 53c94 baseboard SCSI.
ascvar.h: shared softc declarations
asc_ioasic.c: ioasic front-end code.
asc_tc.c: Turbochannel option (and 5000/200 basebard) front-end code.
* ioasic_attach meeds more work to eliminate pmax_type dependency
and to verify the clocks speed passed to 53c94.
* Add prototypes for asc script entry points; should compile with
-Wstrict-prototypes -Wmissing-prototypes.
* Use tcvar.h interface. The usage of tc_syncbus() and tc_mb() may
not be quite stylistically on an Alhpa, but it apparently makes no
difference on the eerly-generation Alpha CPUs in TC Alphas.
if the version is <= SCSI-2. This should help some older SCSI
devices that previously needed the "NOLUNS" quirk. While this is
not strictly necessary on SCSI-2 devices, the spec allows it,
so we set it for SCSI-2 devices "just in case". See section 7.2.2 of
Draft X3T9.2 Rev 10L for details.
multi-channel driver), or to SCSI_CHANNEL_ONLY_ONE if a
single-channel driver.
(2) use scsiprint() rather than a locally-defined autoconfig print
function, and kill any locally-defined print function.
(2) in scsibusmatch, match channel as appropriate.
(3) add a scsiprint() function, to do the "scsibus at..."
and channel (if not SCSI_CHANNEL_ONLY_ONE) printing,
i.e. the common functionality that all SCSI drivers currently
should be doing.
a char *, because that's what was really intended, and because
if the print function modifies the string, various things could become
unhappy (so the string should _not_ be modified).
Fix so that resource wait queueing works.
Changed all functions to take a pointer to uba_softc instead of unit
number, except for ubareset(). This must be done later.
the lowest bit set. This isn't any more or less valid according to the PCI
spec, but it deals with lame devices that don't implement all of the top
bits.
a boot string for firmware that can do this, such as the SPARC and
the sun3 models. It is currently silently ignored on all other
hardware now, however. The MD function "boot()" has been changed to
also take a char *.
values, i.e. 0xfffffffe and 0xffffffff respectively. The changed
definitions were incorrect, according to the PCI Local Bus Specification
(Revision 2.0). Further rationale and a workaround for the broken
devices that instigated the change provided in a message to
current-users@netbsd.org, dated Mon, 05 Aug 1996 22:06:58 -0400,
message ID 16773.839297218@ux2.sp.cs.cmu.edu>.
- In egstart(), if the Send Packet command fails, m_freem()
the mbuf chain before dequeueing another one (memory leak).
- In egintr(), return 1 if a known interrupt was processed.
Would manifest itself as spurious interrupts.
thorpej