by me:
* Speed up reading/writing buffers from the hardware by avoiding
slow forward seeks. In preparation to use the optimization, do
not read overlapping bytes. This is currently disabled, but can
be enabled with OPTIMIZE_RW_DATA.
* Hand 802.11 and Prism-specific frames to BPF. User can watch these
frames by specifying an alternate DLT to e.g. tcpdump(8).
* Add support for SIOC[SG]80211BSSID and SIOC[SG]80211CHANNEL.
* Issue join requests and track join/create state through link-status
notifications.
* Split wi_rxeof into separate routines for receiving Ethernet II,
802.11 data, and 802.11 management frames.
* Bug fix: Account for aligning m_data to a word boundary in the Rx
buffer size check.
* Bug fix: Check for LLC/SNAP even if the firmware tells us the frame
is Ethernet II, as the firmware sometimes gets this wrong.
* Process as many events as possible when we get an interrupt, using
a simple heuristic to avoid reprocessing an event (which can have
bad side-effects). Clamp the time spent in the interrupt handler
to 4ms.
* Redo the timeout loops to be consistent and less prone to error.
* Add delays to timeout loops which were missing them, so that a
fast CPU won't win the race.
* Borrow some timeout loop values from the linux-wlan-ng driver,
which seems to reflect a high level of clue (due to direct support
from Intersil).
* Get rid of silly wi_read_data(..., len + 2) idiom; simply round up
in wi_read_data() and wi_write_data(). Also, protect against a
length of 0.
* Name some frequently-used constants. Correct spelling. Other style nits.
* Bug fix: On Prism, set Create IBSS register to 0 *always*. The meaning
of Create IBSS == 1 is join an IBSS or *ESS*, and we do not want to
join an ESS, because that would put us in an inconsistent state. 0
is the right value for Prism.
* Bug fix: Clean up state at the top of wi_init(), in the event that
we don't reach the bottom.
* Simplify wi_start() by always providing an RFC1042-encoded 802.11
frame to the firmware.
* Larval powersave support for HostAP mode, enabled by WI_HOSTAP_POWERSAVE.
* Bug fix: Call wi_stop() from wi_shutdown().
* Bug fix: sync media options with HostAP mode in wi_sync_media().
* In wi_media_status(), inquire firmware for current media state if
media == auto. From FreeBSD.
* Clean up the way buffer lengths are computed by using pointer
arithmetic rather than magic constants.
* Swap the order of comparisons in addr_cmp() for speed.
* Bug fix: Send ReAssoc Response instead of Assoc Response to a
ReAssoc Request.
* Bug fix: Copy SSID using the correct size.
* Give more meaningful names to offsets in a wi_frame.
* Bug fix: Assign the right values to the named constants for
Rx frame encoding.
* Get rid of useless SNAP constants.
This merge changes the device switch tables from static array to
dynamically generated by config(8).
- All device switches is defined as a constant structure in device drivers.
- The new grammer ``device-major'' is introduced to ``files''.
device-major <prefix> char <num> [block <num>] [<rules>]
- All device major numbers must be listed up in port dependent majors.<arch>
by using this grammer.
- Added the new naming convention.
The name of the device switch must be <prefix>_[bc]devsw for auto-generation
of device switch tables.
- The backward compatibility of loading block/character device
switch by LKM framework is broken. This is necessary to convert
from block/character device major to device name in runtime and vice versa.
- The restriction to assign device major by LKM is completely removed.
We don't need to reserve LKM entries for dynamic loading of device switch.
- In compile time, device major numbers list is packed into the kernel and
the LKM framework will refer it to assign device major number dynamically.
back-end to indicate that the device always sees reads as 32-bit
transactions, even if the host does 8 or 16-bit reads.
This is necessary for the SH-5 "Cayman" on-board ethernet. The SMsC part
is behind an FPGA which maps all cpu reads to 32-bits transactions.
- aging ang clear inactivity stations
- DTIM field in beacon/probe response.
- ignore IFF_PROMISC for hostap mode, since 802.11 has 3 address fields,
so that promisc mode is not required for AP function.
written (i.e. is used uninitialised). The esiop SCRIPT may do this in some
circonstances (and it is safe) so bus_space_set_region_4() the RAM in
reset routine.
Problem reported and fix tested by Allen Briggs.
- Fix one typo (instead of two disable_rx, one disable_rx and one disable_tx)
[The other bug fix isn't appropriate since the was OACTIVE is dealt with
has been changed in NetBSD.]
mediaopt adhoc 802.11 adhoc (IBSS) mode. IBSS creation is enabled
for cards which can create IBSS.
mediaopt adhoc,flag0 old lucent adhoc demo mode.
Note that [adhoc] media options for wi driver was used for adhoc demo mode,
which is NOW CHANGED.
load f/w images > 0x7fff words), set ISP_FW_ATTR_SCCLUN. We explicitly
don't believe we can find attributes if f/w is < 1.17.0, so we have to
set SCCLUN for the 1.15.37 f/w we're using manually- otherwise every
target will replicate itself across all 16 supported luns for non-SCCLUN
f/w.
EXCLUDE_UNENCRYPTED bit in the WI_RID_P2_ENCRYPTION value if we are
in shared key mode. Symbol cards, just to be different, supposedly
always want the EXCLUDE_UNENCRYPTED bit set (confirmed with the
Linux orinoco and spectrum24 drivers).
* Flesh out the Host-AP WEP transmit side. Note this does not yet
work properly; the frame as seen by the receiver FCS's incorrectly.
Both changes from OpenBSD. Not confirmed whether or not Host-AP WEP
works with OpenBSD (mail sent to millert).
WEP for APs is not yet implemented, but without WEP, this works well
enough for my laptop to associate with an AP running this code.
Adapted from OpenBSD.
in this info based on firmware type and version. Replace "wi_has_wep"
with a flag.
* For cards which support IBSS, add "ibss" has a media option.
* For cards which support CREATE_IBSS, add "ibss-master" as a media
option.
* Use the "ibss" and "ibss-master" media options to determine if
we should go into IBSS mode and/or create the IBSS.
* Internally convert between the generic WI_PORTTYPE_IBSS and the
value the firmware wants to use for IBSS.
* When setting the IBSS name, if a desired-SSID is set, and we're
an ibss-master, write the desired-SSID into the own-SSID slot.
This ensures that "ifconfig wi0 nwid FOO" will do the expected
thing.
* Only set the roaming mode if the card supports roaming.
From OpenBSD.
Always init chip via I/O space.
Map only I/O registers we actually need.
Automatically detect if we need to do bswapping
Add (untested) code to use automagic bswap on CyberPro.
Report video memory amount.
Report if/how bswapping is done.
-treat the builtin font like any other font at runtime
-for that, copy it to malloc()'d memory during attach()
-in early console initialization, if we have to consider a broken card
(VGA_CONSOLE_ATI_BROKEN_FONTSEL), copy the builtin font to another
location in font ram; the attach() code will do the rest
put the "quirk" code into effect again
found on many (all?) of PCI-based ATI graphics cards. It is fully optional
and can be enabled by adding `options VGA_CONSOLE_ATI_BROKEN_FONTSEL'
to config file.
- Temporarily remove `quirk' mechanism. Similar code already exists
in pci_quirks.c.
-Don't assume fonts to start with character 0, load at the
right offset. Now we can use eg wsfont/bold8x16.h which
starts with chr(1).
-Don't touch the hardware if a font is set for a screen which is
not active.
make the number of available font slots variable,
set up a "quirk" mechanism to tell the generic vga code about crippled
VGA adapters which ignore the "fontsel" TS register,
initiate the quirk table with an ATI chip which happened to be on a board
I tested with.
Afaik quite a number of ATI chips suffers from the "loaded fonts don't
work" problem - these should be added.
Bad side effect of my change: The builtin font will be kicked out
always if a VGA_CONSOLE_SCREENTYPE is specified which needs a loaded
font. In early console initialization, we don't know much about the
graphics card, so we have to assume the worst (ie ATI:-).
Do a fallback on reading stuff from the fabric. Some devices/initiators
don't correctly register their type with the fabric nameserver. This
seems to be due to a misinterpretation of what TYPE should mean for a
CT_HDR. In any case, do a fallback to try and catch these misentered
entities.
Add some stuff for default framesize and throttle. Fix some buglets.
- implement SIMPLEQ_REMOVE(head, elm, type, field). whilst it's O(n),
this mirrors the functionality of SLIST_REMOVE() (the other
singly-linked list type) and FreeBSD's STAILQ_REMOVE()
- remove the unnecessary elm arg from SIMPLEQ_REMOVE_HEAD().
this mirrors the functionality of SLIST_REMOVE_HEAD() (the other
singly-linked list type) and FreeBSD's STAILQ_REMOVE_HEAD()
- remove notes about SIMPLEQ not supporting arbitrary element removal
- use SIMPLEQ_FOREACH() instead of home-grown for loops
- use SIMPLEQ_EMPTY() appropriately
- use SIMPLEQ_*() instead of accessing sqh_first,sqh_last,sqe_next directly
- reorder manual page; be consistent about how the types are listed
- other minor cleanups
PowerPC and provides a PCI-host bridge, interrupt controller, two com ports,
two IIC ports, a timer, and a DRAM controller.
The driver supports PCI, interrupts and com ports.
to check if we get a RQCS_DATA_UNDERRUN - if we're an FC card, we may
not have RQCS_RU set- if it isn't set, we just lost a DATA XFR IU in the
middle of the exchange. In this case, we have to bomb out the whole xfer.
We had been getting silent data corruption before.
Fix receiver lockups. When writing the RX Kick register, we need back up
on descriptor since we advanced one in the for loop. That will be the
last descriptor we haven't processed which is what we should write.
switch back to MII mode. Keep a sliding window for TX segments and when it
gets > 2/3 full, request a TX interrupt (window gets reset when the h/w TX
queue is empty). Add dv_xname to a few printfs. With the above changes,
the gem driver will now work on Macintoshes, even in GigE mode. On a 733
PowerMac G4 it gets ~355Mb/s TX and ~280Mb/s RX to/from an Alpha XP1000.
XXX mii autoselect is still flakey.
errors for narrow transfers after a reselect. FreeBSD sym driver has a comment
about this, but their workaround (disable SCSI gross error reports) doesn't
work for me. Instead dissallow disconnect if the target is not wide
(FreeBSD doens't allow disconnect until the target has been fully probed, which
is why they may not have noticed my problem).
particular, make sure that all the SIASTAT_ANS bits are in the right state
so we don't do something inane.
Still doesn't actually bring the link up properly, but at least it negotiates
most of the time, and does it a little faster.
1) Do not call tlp_sia_update_link() in Nway mode, and do not look at SIASTAT
in any other place that nway_status(), where we first check that it's valid.
In other places, look at IFM_ACTIVE after having call nway_status().
2) Eliminate stupid MII_MEDIACHG calls, and arrange for nway_service() to
update status on every call.
3) Nuke the synchronous case of nway_auto() from orbit.
4) Do not call nway_statchg() when using manual configuration; tlp_sia_set()
does everything we need.
1) Set OPMODE_TTM in the default tsti_opmode, so that nway_status doesn't
blow up and report the wrong media type when statically configured. (This
code is a hack.)
2) Do not set IFM_ACTIVE (i.e. ignore SIASTAT_LS*) when in auto-negotiation
mode and negotiation has not completed (per 21143 manual).
3) Do not clear auto-negotiation mode; otherwise the chip will not
renegotiate on a link failure.
With these changes, 10/100 selection is more stable, and auto-negotiation
comes up with the right status and detects link, but the link does not work
unless it's hardwired. More work is needed.
It is unclear if this realy is needed and if, on which type of cards. I
haven't run accross a card that needs it yet. This may have been just
a copy & pasto from the ISAC interrupt handler carried over to IPAC.
Remove the clear-the-irq-after-enabling it dance (which had bad side
effects on some cards). Instead disble the ISAC receiver when we have
interrupts disabled. Adjust the interrupt handler to properly deal with
subtle differences of the ISAC implementation in IPAC chips.
if error occurs after status is collected) race condition
when using the status byte to detect completed commands (a command descriptor
could be recycled before the device disconnected), and make the
interrupt routine handling completed commands more efficient (no need to
scan target * lun * tag array any more).
there may be tagged commands still running when we queue a request sense
command.
Solve this by using 2 DSA entry per LUN
- Now that we have the command DSA before select, we can load T/L/Q in
SCRATCHC. This makes the selection timeout handler simpler.
- Avoid a race condition when setting the free flag in the cmd ring (see
comment in the script)
- don't forget to update the ID in the head of LUN table after a sync/wide
negotiation. This fixes the command timeout at the first data command
after negotiation (the bus reset handler did update the ID properly,
so subsequent commands were OK).
- for DMA interrupts, clear fifo if it's not empty. Leaving the fifo dirty
would prevent subsequent interrupts from coming in.
- Various improvements in debug messages
- misc cleanups.
scheduler slot. This costs a few more instructions but divide the size of the
scheduler ring by 2, saving 1k of onboard RAM (a bus with 15 devices would
overflow the on-board RAM by 128 bytes).
- Add support for DT transfers (aka Ultra/160) in esiop
Note that DT transfers are not enabled for 53c1010-33 rev 0 yet; if I trust
FreeBSD it has a bug which prevent them to do DT properly.
From the same source there may be issues with some revs of 53c1010-66.
taken from OpenBSD. Test hardware kindly provided by Intel. This still needs
management bits, and doesn't support older controllers, but that shouldn't
be hard to fix.
For this add another indirecton: the DSA in the LUN table points to
a table of DSA indexed by the tag number when tagged command is in use.
For non tagged command, the LUN DSA still points to the tables describing the
xfer directly.
yet.
If is restricted to SIOP which implement the load/store instruction, and
has 10 scratch registers (basically, 825 and newer, possibly 770).
It implements a different interface between host and script, using a real
ring for command starts, and improved support for reconnect which will allow
256 tag per device. It uses interrupt on the fly to signal complete command,
which allows several commands to be serviced per interrupt and doesn't require
the script to stop to signal command completion.
3 bits are lun address modifiers.
Remove code that (incorrectly) thought it was asking the f/w to only
PLOGI if not already PLOGI'd. The current f/w documentation tells us
that we have this backwards.
"true" at the appropriate times for non-PCMCIA interfaces. This
means that the ENETRESET path in cs_ioctl() now runs, thus fixing
multicast (and IPv6) on my Shark. Yay.
* Simplify cs_hash_index(): Rather than taking the bottom 6 bits of
a big-endian CRC32 and reversing them, just take the top 6 bits of
a little-endian CRC32.
WI_RID_SCAN_APS in previous commit works for Intel Pro/Wirelss 2011
with firmware 2.51.1.
It seems that the firmware automatically updated after the card runs on
Windows 2000 with 2011_2011B_CD_3.0 in Intel web site.
The card is Type 1 CF card and it doesn't have firmware in.
So we need to download the firmware image into the card before
touching it.
XXX downloading code should be written in generic (bus independent),
but I don't have enough information for now.
- The version string doesn't need to start with 'V'.
- Symbol firmware also support CREATE_IBSS.
- But it doesn't support ROAMING_MODE nor MICROWAVE_OVEN.
into a strange failure mode if we do it with disabled interrupt. When
(re-)enabling interrupts reset transmitter and receiver and clear any
pending state.
not pre-load the chip's Tx buffer, but instead waits for the Tx Ready
interrupt to transmit the first chunk of data.
* On the IOP310, set COM_HW_NO_TXPRELOAD, rather than COM_HW_TXFIFO_DISABLE.
This solves the "UART hangs" problem on the Npwr in a nicer way (i.e. we
get to use the FIFO, whee). The COM_HW_NO_TXPRELOAD happens to match the
Linux 16550 driver's Tx algorithm, and the "UART hang" was never observed
on the Npwr running Linux.
Eventually, we might want to eliminate the COM_HW_NO_TXPRELOAD, and simply
always use its algorithm. But it should be tested on more 16x50 variants
before we do that.
Kudos to Valeriy Ushakov <uwe@netbsd.org> for pointing out this solution
(which also happens to fix the stray UART interrupt issue on the Krups
Javastation), and to Allen Briggs <briggs@netbsd.org> for experimenting
with various methods of fixing this.
are used- didn't make a difference, but hey...
Put in commented out GFF_ID code- for use in future attempts to search
the fabric- this probably has to go thru the management server path.
Don't whine about handles we can't find if these are aborted commands
(we know we can't find the handles because we destroy handles after
a successful mailbox abort- we don't wait for the F/W to decide whether
it wants to return a status IOCB after this happens).
the data transfer. This is mandatory for data out commands (although none are
used for now), and not forbiddend for data in commands. Also record if we
did transfers any data.
May solve kern/16159 by making the probe more robust in face of fake identify.
for the same purpose (ignoring invalid interrupts).
For cards that are not able to stop all interrupts (or we don't know a way
to do that in software, at least) run the clearirq callback even when
ignoring an interrupt because we are not enabled. Otherwise the card would
stop interrupting.
Reserve a driver specific callout handle and an int value in the generic
isic_softc to allow card drivers to implement fancy blinkenlights.
It improves playing/recording quality greatly
and it was almost done by Yosuke Sugahara <penta@fuchu.or.jp>.
Thanks a lot!
Add support of slinear8, slinear16_le, slinear16_be.
pcmcia cards. Now that pcmcia attachements properly handle the activate
callback, this is no longer needed (and is suspect to cause completely
unrelated problems.)
count them when reading the NIC counters - it doubles the count. Read the
NIC counters to prevent counter overflow interrupts, but don't add them to
the interface counters. Don't bother reading the upper counts because they
are just latched when reading the totals.
Fixes final part of PR#11549.
on the following PRO/100 chips:
* i82558 step A4
* i82558 step B0
* i82559 step A0
* i82559S step A
* i82550
* i82550 step C
The interrupt delay is configurable on all microcodable chips. The
maximum "bundle" size (packet count) is configurable on all but the
i82558.
The microcode is enabled by setting IFF_LINK0 on the interface.
Derived from code in FreeBSD.
the interface was wired to full-duplex mode. Duh.
Also, add OPMODE_TTM to OPMODE_MEDIA_BITS, to insure that it is changed when
we switch between 10 and 100.
to be trying to wriggle out of supporting this well. Instead, use
GID_FT to get a list of Port IDs and then use GPN_ID/GNN_ID to find the
port and node wwn. This should make working on fabrics a bit cleaner and
more stable.
This also caused some cleanup of SNS subcommand canonicalization so that
we can actually check for FS_ACC and FS_RJT, and if we get an FS_RJT,
print out the reason and explanation codes.
We'll keep the old GA_NXT method around if people want to uncomment a
controlling definition in ispvar.h.
This also had us clean up ISPASYNC_FABRICDEV to use a local lportdb argument
and to have the caller explicitly say that a device is at the end of the
fabric list.
The ICH on-board Ethernet and some i82559 chips have a bug which
will cause a PCI protocol violation if the chip receives a CU_RESUME
command as it is entering the IDLE state by deasserting #CLKRUN.
(This is the so-called "resume bug" that we previously had an incomplete
work-around for on ICH chipsets.)
The work-around is to disable Dynamic Standby Mode, such that the
chip will never deasert #CLKRUN. Dynamic Standby Mode is disabled
by clearing a bit in the EEPROM and updating the EEPROM (and EEPROM
checksum).
Unfortunately, the chip will only consult the EEPROM setting after
a PCI bus reset, so a system reboot is required once the EEPROM
has been updated (the EEPROM update only needs to happen once,
and the driver usses a warning instructing the user to reboot the
system once the work-around has been applied).
Issue pointed out by David Brownlee, and code more-or-less lifted
from FreeBSD.
for bus_dmamap_sync calls. They'd been blindly ported from Solaris which
had *one* dma map for the entire control space, so offset was incremented
for the Request, Response and FC Scratch spaces. Tsk. There are three maps
in NetBSD. I should probably make them one anyway.
1. Fix setting of nominal fan speeds with ENVSYS_STREINFO.
2. Treat Winbond 83781D specially because it has a programmable divisor for
FAN3 unlike generic devices.
3. Set nominal RPMs.
4. Fix a typo in the code for setting FAN3's divisor for W83782 type
hardware monitors.
possible pending interrupt. This should avoid the interrupt loop described
in PR kern/15841.
It is safe to read status here, because if we're not waiting for an interrupt
we have no command pending, so the device should be idle.
(de)activate for pcmcia cards.
Implement detach/(de)activate for PCI cards.
Clean up internal state (free call-descriptors) if a controller is
detached while it has open connections.
B-channel and D-channel drivers separately) split the Fritz!PCI card
driver out of the isic driver.
The new device is called "ifpci" and uses the same D-channel driver as the
isic devices, but has it's own B-channel driver.
mycroft