WI_RID_DBM_ADJUST: In preparation for capturing Prism packets
containing received signal strength indications (RSSI), read the
constant for conversion from RSSI to dBm (decibels relative to
a milliwatt).
WI_RID_FRAG_THRESH: Get/set the packet fragmentation threshold
on Lucent/Prism.
- Move lm_readreg/lm_writereg into the front-ends. Add/use function pointers
in the softc.
- Add a bank select function pointer to the softc and provide a generic
version. WinBond chips accessed over serial bus present three addresses,
two of which are used to access bank 1/2 registers.
- Mark TSENS2/3 sensor data as invalid if the the corresponding bank select
fails.
- Handle IFF_ALLMULTI case correctly. This is necessary to mrouted working.
Tested by taca@netbsd.org.
- Clear unnecessary multicast hash bit. Otherwise, unnecessary multicast
packet is received. Tested by me with the 3C905C bought at akihabara.
It was 2980yen.
The code is written by fvdl@netbsd.org and me.
computed again in siop_add_reselsw()
in siop_reset(), reset the tag reseloff to 0, in addition to the lun reseloff.
If siop_add_dev() fails this time we would use the old reseloff, clobbering
memory now used for something else.
kqueue provides a stateful and efficient event notification framework
currently supported events include socket, file, directory, fifo,
pipe, tty and device changes, and monitoring of processes and signals
kqueue is supported by all writable filesystems in NetBSD tree
(with exception of Coda) and all device drivers supporting poll(2)
based on work done by Jonathan Lemon for FreeBSD
initial NetBSD port done by Luke Mewburn and Jason Thorpe
Add codec id of VT1616.
ALC650 codec specific chagne:
Add outputs.surround.mixtofront,
outputs.center.mixtofront, and outputs.lfe.mixtofront.
VT1616 codec specific change:
Add outputs.surround.mixtofront,
outputs.center.mixtofront, and outputs.lfe.mixtofront.
(Not tested)
XXX: We should provide ac97(4) manual page and describe
codec-specific features.
ISP_DAC_SUPPORTED is defined and do a real typedef for the size
of DMA addresses. ISP_DAC_SUPPORTED also decides how much of any
particular DMA address is significant.
Lose STRNCAT over the side.
Add in (sight unseen) 10160 support.
Start doing the work necessary to support DAC (Dual Address Cycle)
environments. This allows for direct DMA to > 4GB memory from a PCI
card.
Lose STRNCAT over the side and use SNPRINTF instead.
to char-cell based vga(4) driver, and fully compatible with existing
apps like XFree86. Currently it supports 80x25, 80x30, 80x40 and 80x50
text modes using emulation. You can enable it by specifying `options
VGA_RASTERCONSOLE' in your kernel config file.
Note that displaying multilingual text doesn't work yet. Necessary
code is already there, but userland stuff and some functionality isn't
ready for prime time yet. I'm working on them.
It seems that the firmware accept 104bit key only if
all the keys have 104bit length. We get the length of
the transmit key and use it for all other keys.
Perhaps we should use software WEP for such situation.
- Add "outputs.surround", "outputs.center", and "outputs.lfe"
- If the codec is not capable of a feature, mixer variables
about the feature is not created. For example, no
"outputs.tone" for a codec without tone control.
- Set the following mixer values in ac97_attach():
outputs.master=127,127
outputs.master.mute=off
outputs.headphones.mute=off
outputs.surround=127,127
outputs.surround.mute=off
outputs.center=127
outputs.center.mute=off
outputs.lfe=127
outputs.lfe.mute=off
inputs.dac.mute=off
inputs.cd.mute=off
inputs.line.mute=off
inputs.aux.mute=off
inputs.video.mute=off
record.volume.mute=off
because the default setting of AC'97 codec (all mutes are on,
and maximum volume) is troublesome.
- Make "char*" parameters of ac97_get_portnum_by_name() "const char*"
Codec ID changes:
- If a codec ID is unknown but its vendor ID is known,
ac97_attach() prints the vendor name like "dev0: <vendor name>
unknown (0xXXXXXXXX) codec;"
- Add IDs of Asahi Kasei AK4542, AK4544, AK4544A, AK4545,
Realtek ALC100
- Correct a vendor name: "Advance Logic" -> "Avance Logic"
- Add capability of codec-specific initialization
ac97_attach():
- CDAC, SDAC, and LDAC are eanabled.
- DELAY() before mixer settings. ThinkPad X24 needs it.
ALC650 codec specific change:
- Add "outputs.surround.lineinjack" to switch the line-in jack
to the surround output
- Add "outputs.center.micjack" and "outputs.lfe.micjack" (alias
of "outputs.center.micjack") to switch the mic jack to the
center/lfe output.
ac97_attach(): Enable VRA/VRM if the codec is capable of them.
The struct ac97_softc keeps the clock of the codec, the basic
features flag (the value of AC97_REG_RESET), and the extended
features flag (the value of AC97_REG_EXT_AUDIO_ID).
ac97_codec_if: Add get_extcaps(), set_rate(), and set_clock()
methods.
since it can be updated by IBSS merge. Also the lucent firmware 8.10.1
changes random generated bssid every 10 seconds in IBSS creation enable.
PR 18520
- Split if_fmv.c into MI/MD part and add ISA-PnP attachment for FMV-183.
(XXX FMV-184 is not tested. It would require extra media-select functions..)
- Fix probe functions of fmv_isa so that FMV-181A/182A will also match.
Fixes port-i386/9476.
times changing of 802.11 parameters, such as nwid, the error
"tx buffer allocation failed" occured unless ifconfig down up.
Pass signal streangth and timestamp to ieee80211_input, though it is not
useful for wi driver for now.
correctly. To avoid massive extra code in each driver, now if_iee80211subr.c
also handles non-standard old lucent adhoc-demo mode.
This also fixes PR 14227.
- Eliminate wi_hostap.c since most of the code are duplicated with
net/if_ieee80211subr.c
- Station for Infrastructure network and IBSS also use service functions
as much as possible to be consistent with other wireless drivers.
Now WEP works for station/ibss/hostap.
Change the name of structure ieee80211_bss to ieee80211_node, which is
used for management of stations in hostap mode, and peers in ibss mode.
Split off ic_opmode, ic_phytype from ic_flags.
Preparation to merge 'wi' driver into 80211subr.c.
Setup sequence obtained from Krups OFW with some CyberPro-specific
magic from Linux driver. The driver still has a lot of hardcoded
stuff, but it is useful enough to bring up wscons on netwinder.
XXX: Proper console attachment needs to be written (the driver was
originally developed on sparc, where our approach to attaching console
is totally different).
Caveat emptor!
by me:
* Speed up reading/writing buffers from the hardware by avoiding
slow forward seeks. In preparation to use the optimization, do
not read overlapping bytes. This is currently disabled, but can
be enabled with OPTIMIZE_RW_DATA.
* Hand 802.11 and Prism-specific frames to BPF. User can watch these
frames by specifying an alternate DLT to e.g. tcpdump(8).
* Add support for SIOC[SG]80211BSSID and SIOC[SG]80211CHANNEL.
* Issue join requests and track join/create state through link-status
notifications.
* Split wi_rxeof into separate routines for receiving Ethernet II,
802.11 data, and 802.11 management frames.
* Bug fix: Account for aligning m_data to a word boundary in the Rx
buffer size check.
* Bug fix: Check for LLC/SNAP even if the firmware tells us the frame
is Ethernet II, as the firmware sometimes gets this wrong.
* Process as many events as possible when we get an interrupt, using
a simple heuristic to avoid reprocessing an event (which can have
bad side-effects). Clamp the time spent in the interrupt handler
to 4ms.
* Redo the timeout loops to be consistent and less prone to error.
* Add delays to timeout loops which were missing them, so that a
fast CPU won't win the race.
* Borrow some timeout loop values from the linux-wlan-ng driver,
which seems to reflect a high level of clue (due to direct support
from Intersil).
* Get rid of silly wi_read_data(..., len + 2) idiom; simply round up
in wi_read_data() and wi_write_data(). Also, protect against a
length of 0.
* Name some frequently-used constants. Correct spelling. Other style nits.
* Bug fix: On Prism, set Create IBSS register to 0 *always*. The meaning
of Create IBSS == 1 is join an IBSS or *ESS*, and we do not want to
join an ESS, because that would put us in an inconsistent state. 0
is the right value for Prism.
* Bug fix: Clean up state at the top of wi_init(), in the event that
we don't reach the bottom.
* Simplify wi_start() by always providing an RFC1042-encoded 802.11
frame to the firmware.
* Larval powersave support for HostAP mode, enabled by WI_HOSTAP_POWERSAVE.
* Bug fix: Call wi_stop() from wi_shutdown().
* Bug fix: sync media options with HostAP mode in wi_sync_media().
* In wi_media_status(), inquire firmware for current media state if
media == auto. From FreeBSD.
* Clean up the way buffer lengths are computed by using pointer
arithmetic rather than magic constants.
* Swap the order of comparisons in addr_cmp() for speed.
* Bug fix: Send ReAssoc Response instead of Assoc Response to a
ReAssoc Request.
* Bug fix: Copy SSID using the correct size.
* Give more meaningful names to offsets in a wi_frame.
* Bug fix: Assign the right values to the named constants for
Rx frame encoding.
* Get rid of useless SNAP constants.
This merge changes the device switch tables from static array to
dynamically generated by config(8).
- All device switches is defined as a constant structure in device drivers.
- The new grammer ``device-major'' is introduced to ``files''.
device-major <prefix> char <num> [block <num>] [<rules>]
- All device major numbers must be listed up in port dependent majors.<arch>
by using this grammer.
- Added the new naming convention.
The name of the device switch must be <prefix>_[bc]devsw for auto-generation
of device switch tables.
- The backward compatibility of loading block/character device
switch by LKM framework is broken. This is necessary to convert
from block/character device major to device name in runtime and vice versa.
- The restriction to assign device major by LKM is completely removed.
We don't need to reserve LKM entries for dynamic loading of device switch.
- In compile time, device major numbers list is packed into the kernel and
the LKM framework will refer it to assign device major number dynamically.
back-end to indicate that the device always sees reads as 32-bit
transactions, even if the host does 8 or 16-bit reads.
This is necessary for the SH-5 "Cayman" on-board ethernet. The SMsC part
is behind an FPGA which maps all cpu reads to 32-bits transactions.
- aging ang clear inactivity stations
- DTIM field in beacon/probe response.
- ignore IFF_PROMISC for hostap mode, since 802.11 has 3 address fields,
so that promisc mode is not required for AP function.
written (i.e. is used uninitialised). The esiop SCRIPT may do this in some
circonstances (and it is safe) so bus_space_set_region_4() the RAM in
reset routine.
Problem reported and fix tested by Allen Briggs.
- Fix one typo (instead of two disable_rx, one disable_rx and one disable_tx)
[The other bug fix isn't appropriate since the was OACTIVE is dealt with
has been changed in NetBSD.]
mediaopt adhoc 802.11 adhoc (IBSS) mode. IBSS creation is enabled
for cards which can create IBSS.
mediaopt adhoc,flag0 old lucent adhoc demo mode.
Note that [adhoc] media options for wi driver was used for adhoc demo mode,
which is NOW CHANGED.
load f/w images > 0x7fff words), set ISP_FW_ATTR_SCCLUN. We explicitly
don't believe we can find attributes if f/w is < 1.17.0, so we have to
set SCCLUN for the 1.15.37 f/w we're using manually- otherwise every
target will replicate itself across all 16 supported luns for non-SCCLUN
f/w.
EXCLUDE_UNENCRYPTED bit in the WI_RID_P2_ENCRYPTION value if we are
in shared key mode. Symbol cards, just to be different, supposedly
always want the EXCLUDE_UNENCRYPTED bit set (confirmed with the
Linux orinoco and spectrum24 drivers).
* Flesh out the Host-AP WEP transmit side. Note this does not yet
work properly; the frame as seen by the receiver FCS's incorrectly.
Both changes from OpenBSD. Not confirmed whether or not Host-AP WEP
works with OpenBSD (mail sent to millert).
WEP for APs is not yet implemented, but without WEP, this works well
enough for my laptop to associate with an AP running this code.
Adapted from OpenBSD.
in this info based on firmware type and version. Replace "wi_has_wep"
with a flag.
* For cards which support IBSS, add "ibss" has a media option.
* For cards which support CREATE_IBSS, add "ibss-master" as a media
option.
* Use the "ibss" and "ibss-master" media options to determine if
we should go into IBSS mode and/or create the IBSS.
* Internally convert between the generic WI_PORTTYPE_IBSS and the
value the firmware wants to use for IBSS.
* When setting the IBSS name, if a desired-SSID is set, and we're
an ibss-master, write the desired-SSID into the own-SSID slot.
This ensures that "ifconfig wi0 nwid FOO" will do the expected
thing.
* Only set the roaming mode if the card supports roaming.
From OpenBSD.
fvdl