For the CXL PXB there is additional code after pxb_dev_realize_common()
is called. If that realize failed (e.g. due to an out of range numa_node)
we will get a segfault. Return a bool so the caller can check if the
pxb_dev_realize_common() succeeded or not without having to poke around
in the errp.
Fixes: 4f8db8711c ("hw/pxb: Allow creation of a CXL PXB (host bridge)")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To establish performance characteristics of a CXL device when used via a
particular CXL topology (root ports, switches, end points) it is necessary
to set the appropriate link speed and width in the PCI Express capability
structure. Provide x-speed and x-link properties for this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Copied from gen_pcie_root_port.c
Drop the previous code that ensured a valid value in s->width, s->speed
as now a default is provided so this will always be set.
Note this changes the default settings but it is unlikely to have a negative
effect on software as will only affect ports with now downstream device.
All other ports will use the settings from that device.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Approach copied from gen_pcie_root_port.c
Previously the link defaulted to a maximum of 2.5GT/s and 1x. Enable setting
it's maximum values. The actual value after 'training' will depend on the
downstream device configuration.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
These are very similar to the recently added Generic Initiators
but instead of representing an initiator of memory traffic they
represent an edge point beyond which may lie either targets or
initiators. Here we add these ports such that they may
be targets of hmat_lb records to describe the latency and
bandwidth from host side initiators to the port. A discoverable
mechanism such as UEFI CDAT read from CXL devices and switches
is used to discover the remainder of the path, and the OS can build
up full latency and bandwidth numbers as need for work and data
placement decisions.
Acked-by: Markus Armbruster <armbru@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916174122.1843197-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable ACPI table creation for PCI Expander Bridges to be independent
of PCI internals. Note that the UID is currently the PCI bus number.
This is motivated by the forthcoming ACPI Generic Port SRAT entries
which can be made completely independent of PCI internals.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The pci-bridge device is not usable on s390x, so introduce a Kconfig
switch that allows to disable it.
Message-ID: <20240913144844.427899-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
Recent commit "qapi: Smarter camel_to_upper() to reduce need for
'prefix'" added a temporary 'prefix' to delay changing the generated
code.
Revert it. This improves HmatLBDataType's generated enumeration
constant prefix from HMATLB_DATA_TYPE to HMAT_LB_DATA_TYPE, and
HmatLBMemoryHierarchy's from HMATLB_MEMORY_HIERARCHY to
HMAT_LB_MEMORY_HIERARCHY.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240904111836.3273842-8-armbru@redhat.com>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
With returned boolean, there's no need to dereference @errp to check
failure case.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-4-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
+jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
=C0UU
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
more memslots support in libvhost-user
support PCIe Gen5/Gen6 link speeds in pcie
more traces in vdpa
network simulation devices support in vdpa
SMBIOS type 9 descriptor implementation
Bump max_cpus to 4096 vcpus in q35
aw-bits and granule options in VIRTIO-IOMMU
Support report NUMA nodes for device memory using GI in acpi
Beginning of shutdown event support in pvpanic
fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmXw0TMPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRp8x4H+gLMoGwaGAX7gDGPgn2Ix4j/3kO77ZJ9X9k/
# 1KqZu/9eMS1j2Ei+vZqf05w7qRjxxhwDq3ilEXF/+UFqgAehLqpRRB8j5inqvzYt
# +jv0DbL11PBp/oFjWcytm5CbiVsvq8KlqCF29VNzc162XdtcduUOWagL96y8lJfZ
# uPrOoyeR7SMH9lp3LLLHWgu+9W4nOS03RroZ6Umj40y5B7yR0Rrppz8lMw5AoQtr
# 0gMRnFhYXeiW6CXdz+Tzcr7XfvkkYDi/j7ibiNSURLBfOpZa6Y8+kJGKxz5H1K1G
# 6ZY4PBcOpQzl+NMrktPHogczgJgOK10t+1i/R3bGZYw2Qn/93Eg=
# =C0UU
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 12 Mar 2024 22:03:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (68 commits)
docs/specs/pvpanic: document shutdown event
hw/cxl: Fix missing reserved data in CXL Device DVSEC
hmat acpi: Fix out of bounds access due to missing use of indirection
hmat acpi: Do not add Memory Proximity Domain Attributes Structure targetting non existent memory.
qemu-options.hx: Document the virtio-iommu-pci aw-bits option
hw/arm/virt: Set virtio-iommu aw-bits default value to 48
hw/i386/q35: Set virtio-iommu aw-bits default value to 39
virtio-iommu: Add an option to define the input range width
virtio-iommu: Trace domain range limits as unsigned int
qemu-options.hx: Document the virtio-iommu-pci granule option
virtio-iommu: Change the default granule to the host page size
virtio-iommu: Add a granule property
hw/i386/acpi-build: Add support for SRAT Generic Initiator structures
hw/acpi: Implement the SRAT GI affinity structure
qom: new object to associate device to NUMA node
hw/i386/pc: Inline pc_cmos_init() into pc_cmos_init_late() and remove it
hw/i386/pc: Set "normal" boot device order in pc_basic_device_init()
hw/i386/pc: Avoid one use of the current_machine global
hw/i386/pc: Remove "rtc_state" link again
Revert "hw/i386/pc: Confine system flash handling to pc_sysfw"
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/core/machine.c
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_usp_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_cap;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And since
cxl_usp_realize() - as a PCIDeviceClass.realize() method - doesn't get
the NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_usp_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-6-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
This CXL component isn't allowed to have a RAS capability.
Whilst this should be harmless as software is not expected to look
here, good to clean it up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240215155206.2736-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When a variable is initialized to &struct->field, use it
in place. Rationale: while this makes the code more concise,
this also helps static analyzers.
Mechanical change using the following Coccinelle spatch script:
@@
type S, F;
identifier s, m, v;
@@
S *s;
...
F *v = &s->m;
<+...
- &s->m
+ v
...+>
Inspired-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240129164514.73104-2-philmd@linaro.org>
Acked-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
[thuth: Dropped hunks that need a rebase, and fixed sizeof() in pmu_realize()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_usp_realize(), @errp is dereferenced without ERRP_GUARD():
cxl_doe_cdat_init(cxl_cstate, errp);
if (*errp) {
goto err_cap;
}
Here we check *errp, because cxl_doe_cdat_init() returns void. And since
cxl_usp_realize() - as a PCIDeviceClass.realize() method - doesn't get
the NULL @errp parameter, it hasn't triggered the bug that dereferencing
the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_usp_realize().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240223085653.1255438-6-zhao1.liu@linux.intel.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When setting GLIB_VERSION_MAX_ALLOWED to GLIB_VERSION_2_58 or higher,
glib adds type safety checks to the g_steal_pointer() macro. This
triggers errors in the build_cdat_table() function which uses the
g_steal_pointer() for type-casting from one pointer type to the other
(which also looks quite weird since the local pointers have all been
declared with g_autofree though they are never freed here). Let's fix
it by using a proper typecast instead. For making this possible, we
have to remove the QEMU_PACKED attribute from some structs since GCC
otherwise complains that the source and destination pointer might
have different alignment restrictions. Removing the QEMU_PACKED should
be fine here since the structs are already naturally aligned. Anyway,
add some QEMU_BUILD_BUG_ON() statements to make sure that we've got
the right sizes (without padding in the structs).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As a failure of g_malloc() will result in QEMU exiting, it
won't return a NULL to check. As such, drop the incorrect handling
of such NULL returns in the cdat table building code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CONFIG_ALL is tricky to use and was ported over to Meson from the
recursive processing of Makefile variables. Meson sourcesets
however have all_sources() and all_dependencies() methods that
remove the need for it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Without these being set the PCIE Link Capabilities register has
invalid values in these two fields.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-10-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable it for the switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid repetition of switch upstream port specific data in the
CXLDeviceState structure it will be necessary to access the switch USP
specific data from mailbox callbacks. Hence move it to cxl_device.h so it
is no longer an opaque structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023160806.13206-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to reduce line lengths where this is used.
Ext seems sufficiently obvious that it need not be spelt out
fully.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Will be needed so there is a defined serial number for
information queries via the Switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230913133615.29876-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to ACPI spec 6.5 5.2.28.4 System Locality Latency and Bandwidth
Information Structure, if the "Entry Base Unit" is 1024 for BW and the
matrix entry has the value of 100, the BW is 100 GB/s. So the
entry_base_unit should be changed from 1000 to 1024 given the comment notes
it's 16GB/s for .latency_bandwidth.
Fixes: 882877fc35 ("hw/pci-bridge/cxl-upstream: Add a CDAT table access DOE")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In build_cdat_table() we do:
*cdat_table = g_malloc0(sizeof(*cdat_table) * CXL_USP_CDAT_NUM_ENTRIES);
This is wrong because:
- cdat_table has type CDATSubHeader ***
- so *cdat_table has type CDATSubHeader **
- so the array we're allocating here should be items of type CDATSubHeader *
- but we pass sizeof(*cdat_table), which is sizeof(CDATSubHeader **),
implying that we're allocating an array of CDATSubHeader **
It happens that sizeof(CDATSubHeader **) == sizeof(CDATSubHeader *)
so nothing blows up, but this should be sizeof(**cdat_table).
Avoid this excessively hard-to-understand code by using
g_new0() instead, which will do the type checking for us.
While we're here, we can drop the useless check against failure,
as g_malloc0() and g_new0() never fail.
This fixes Coverity issue CID 1508120.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230718101327.1111374-1-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Introduce a CONFIG option to build the pcie-to-pci bridge. No
functional change since it's enabled per default for PCIE_PORT=y.
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Message-Id: <72b6599d-6b27-00b5-aac5-2ebc16a2e023@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The failure paths in CDAT file loading did not clear up properly.
Change to using g_auto_free and a local pointer for the buffer to
ensure this function has no side effects on error.
Also drop some unnecessary checks that can not fail.
Cleanup properly after a failure to load a CDAT file.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230421132020.7408-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously, PXB_CXL_DEVICE, PXB_PCIE_DEVICE and PXB_DEVICE all
have PCI_DEVICE as their direct parent but share a common state
struct PXBDev. convert_to_pxb() is used to get the PXBDev
instance from which ever of these types it is called on.
This patch switches to an explicit hierarchy based on shared
functionality. To allow use of OBJECT_DECLARE_SIMPLE_TYPE()
whilst minimizing code changes, all types are renamed to have
the postfix _DEV rather than _DEVICE. The new heirarchy
has PXB_CXL_DEV with parent PXB_PCIE_DEV which in turn
has parent PXB_DEV which continues to have parent PCI_DEVICE.
This allows simple use of PXB_DEV() etc rather than a custom function
+ removal of duplicated properties and moving the CXL specific
elements out of struct PXBDev.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230420142750.6950-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reproduce issue with
configure --enable-qom-cast-debug ...
qemu-system-x86_64 -display none -machine q35,cxl=on -device pxb-cxl,bus=pcie.0
hw/pci-bridge/pci_expander_bridge.c:54:PXB_DEV: Object 0x5570e0b1ada0 is not an instance of type pxb
Aborted
The type conversion results in the right state structure, but PXB_DEV is
not a parent of PXB_CXL_DEV hence the error. Rather than directly
cleaning up the inheritance, this is the minimal fix which will be
followed by the cleanup.
Fixes: 154070eaf6 ("hw/pxb-cxl: Support passthrough HDM Decoders unless overridden")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230420142750.6950-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The CXL r3.0 specification allows for there to be no HDM decoders on CXL
Host Bridges if they have only a single root port. Instead, all accesses
directed to the host bridge (as specified in CXL Fixed Memory Windows)
are assumed to be routed to the single root port.
Linux currently assumes this implementation choice. So to simplify testing,
make QEMU emulation also default to no HDM decoders under these particular
circumstances, but provide a hdm_for_passthrough boolean option to have
HDM decoders as previously.
Technically this is breaking backwards compatibility, but given the only
known software stack used with the QEMU emulation is the Linux kernel
and this configuration did not work before this change, there are
unlikely to be any complaints that it now works. The option is retained
to allow testing of software that does allow for these HDM decoders to exist,
once someone writes it.
Reported-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
--
v2: Pick up and fix typo in tag from Fan Ni
Message-Id: <20230227153128.8164-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to avoid fixing ACPI route description of traditional PCI interrupts on q35
and because we should probably move with the times anyway.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Message-Id: <20230302133709.30373-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
We are missing necessary config write handling for AER emulation in
the CXL root port. Add it based on pcie_root_port.c
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Message-Id: <20230302133709.30373-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Fix capitalization difference between struct name and typedef.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20230206172816.8201-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ICH9 is a south bridge which doesn't necessarily depend on x86, so move
it into the southbridge folder, analoguous to PIIX.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When ACPI PCI hotplug for Q35 was introduced (6.1), it was implemented
by hiding HPC capability on PCIE slot. That however led to a number of
regressions and to fix it, it was decided to keep HPC cap exposed
in ACPI PCI hotplug case and force guest in ACPI PCI hotplug mode
by other means [1].
That reduced meaning of x-native-hotplug to a compat knob [2] for
broken 6.1 machine type.
Rename property to match its current purpose.
1) 211afe5c69 (hw/i386/acpi-build: Deny control on PCIe Native Hot-plug in _OSC)
2) c318bef762 (hw/acpi/ich9: Add compat prop to keep HPC bit set for 6.1 machine type)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-10-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230112140312.3096331-8-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
hw/cxl/cxl.h uses the PXBDev structure tag instead of the typedef
name. The typedef name is defined in hw/pci/pci_bridge.h. Its
inclusion was dropped in the previous commit to break an inclusion
loop.
Move the typedef to hw/cxl/cxl.h, and use it there. Delete an extra
typedef in hw/pci-bridge/pci_expander_bridge.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-3-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
hw/pci/pci_bridge.h and hw/cxl/cxl.h include each other.
Fortunately, breaking the loop is merely a matter of deleting
unnecessary includes from headers, and adding them back in places
where they are now missing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-2-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
and use cast to TYPE_PCI_BRIDGE instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221129101341.185621-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Code has not been used practically since its inception (2004)
f2aa58c6f4 UniNorth PCI bridge support
or maybe even earlier, but it was consuming contributors time
as QEMU was being rewritten.
Drop it for now. Whomever would like to actually
use the thing, can make sure it actually works/reintroduce
it back when there is a user.
PS:
I've stumbled upon this when replacing PCIDeviceClass::is_bridge
field with QOM cast to PCI_BRIDGE type. Unused DEC 21154
was the only one trying to use the field with plain PCIDevice.
It's not worth keeping the field around for the sake of the code
that was commented out 'forever'.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20221129101341.185621-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert the TYPE_CXL_ROOT_PORT and TYPE_PNV_PHB_ROOT_PORT classes to
3-phase reset, so they don't need to use the deprecated
device_class_set_parent_reset() function any more.
We have to do both in the same commit, because they keep the
parent_reset field in their common parent class's class struct.
Note that pnv_phb_root_port_class_init() was pointlessly setting
dc->reset twice, once by calling device_class_set_parent_reset()
and once directly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-5-peter.maydell@linaro.org
Convert the TYPE_PCIE_ROOT_PORT device to 3-phase reset; this is a
necessary precursor to converting any of its child classes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221125115240.3005559-4-peter.maydell@linaro.org
