Current FIFO handling code does not reset RXFE/RXFF flags when guest
resets FIFO by writing to UARTLCR register, although internal FIFO state
is reset to 0 read count. Actual guest-visible flag update will happen
only on next data read or write attempt. As a result of that any guest
that expects RXFE flag to be set (and RXFF to be cleared) after resetting
FIFO will never see that happen.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230123162304.26254-5-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 currently lacks a reset method. Implement it.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-4-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Previous change slightly modified the way we handle data writes when
FIFO is disabled. Previously we kept incrementing read_pos and were
storing data at that position, although we only have a
single-register-deep FIFO now. Then we changed it to always store data
at pos 0.
If guest disables FIFO and the proceeds to read data, it will work out
fine, because we still read from current read_pos before setting it to
0.
However, to make code less fragile, introduce a post_load hook for
PL011State and move fixup read FIFO state when FIFO is disabled. Since
we are introducing a post_load hook, also do some sanity checking on
untrusted incoming input state.
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Message-id: 20230123162304.26254-3-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PL011 can be in either of 2 modes depending guest config: FIFO and
single register. The last mode could be viewed as a 1-element-deep FIFO.
Current code open-codes a bunch of depth-dependent logic. Refactor FIFO
depth handling code to isolate calculating current FIFO depth.
One functional (albeit guest-invisible) side-effect of this change is
that previously we would always increment s->read_pos in UARTDR read
handler even if FIFO was disabled, now we are limiting read_pos to not
exceed FIFO depth (read_pos itself is reset to 0 if user disables FIFO).
Signed-off-by: Evgeny Iakovlev <eiakovlev@linux.microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230123162304.26254-2-eiakovlev@linux.microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present create_fdt() calls htif_uses_elf_symbols() to determine
whether to insert a <reg> property for the HTIF. This unfortunately
creates a hidden dependency to riscv_load_{firmware,kernel} that
create_fdt() must be called after the ELF {firmware,kernel} image
has been loaded.
Decouple such dependency be adding a new parameter to create_fdt(),
whether custom HTIF base address is used. The flag will be set if
non ELF {firmware,kernel} image is given by user.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-Id: <20221229091828.1945072-13-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the HTIF proxy syscall is unsupported. On RV32, only
device 0 is supported so there is no console device for RV32.
The only way to implement console funtionality on RV32 is to
support the SYS_WRITE syscall.
With this commit, the Spike machine is able to boot the 32-bit
OpenSBI generic image.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present for some unknown reason the HTIF registers (fromhost &
tohost) are defined in the RISC-V CPUArchState. It should really
be put in the HTIFState struct as it is only meaningful to HTIF.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QEMU source codes tend to use 's' to represent the hardware state.
Let's use it for HTIFState.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-5-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
struct HTIFState has 3 members for address space and memory region,
and are initialized during htif_mm_init(). But they are actually
useless. Drop them.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-4-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Spike HTIF is poorly documented. The only relevant info we can
get from the internet is from Andrew Waterman at [1].
Add a comment block before htif_handle_tohost_write() to explain
the tohost register format, and use meaningful macros instead of
magic numbers in the codes.
While we are here, correct 2 multi-line comment blocks that have
wrong format.
Link: https://github.com/riscv-software-src/riscv-isa-sim/issues/364#issuecomment-607657754 [1]
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-2-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tweak the semantic patch to drop redundant parenthesis around the
return expression.
Coccinelle drops a comment in hw/rdma/vmw/pvrdma_cmd.c; restored
manually.
Coccinelle messes up vmdk_co_create(), not sure why. Change dropped,
will be done manually in the next commit.
Line breaks in target/avr/cpu.h and hw/rdma/vmw/pvrdma_cmd.c tidied up
manually.
Whitespace in tools/virtiofsd/fuse_lowlevel.c tidied up manually.
checkpatch.pl complains "return of an errno should typically be -ve"
two times for hw/9pfs/9p-synth.c. Preexisting, the patch merely makes
it visible to checkpatch.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221122134917.1217307-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
These memory allocation functions return void *, and casting to
another pointer type is useless clutter. Drop these casts.
If you really want another pointer type, consider g_new().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220923120025.448759-3-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PL011 TRM says that "UARTIBRD = 0 is invalid and UARTFBRD is ignored
when this is the case". But the code looks at FBRD for the invalid case.
Fix this.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Message-id: 1408f62a2e45665816527d4845ffde650957d5ab.1665051588.git.baruchs-c@neureality.ai
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unaligned i/o access on serial UART works on real PCs.
This is used for example by FreeDOS CTMouse driver. Without this it
can't reset and detect serial mice.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/77
Signed-off-by: Arwed Meyer <arwed.meyer@gmx.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220911181840.8933-6-arwed.meyer@gmx.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch drops the name parameter for the virtio_init function.
The pair between the numeric device ID and the string device ID
(name) of a virtio device already exists, but not in a way that
lets us map between them.
This patch lets us do this and removes the need for the name
parameter in the virtio_init function.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <1648819405-25696-2-git-send-email-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There was an off-by-1 in the qcode conversion array bounds
check.
Fixes: e709a61a8f
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Patch created mechanically with:
$ spatch --in-place --sp-file scripts/coccinelle/use-g_new-etc.cocci \
--macro-file scripts/cocci-macro-file.h FILES...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220315144156.1595462-4-armbru@redhat.com>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
isa_init_irq() has become a trivial one-line wrapper for isa_get_irq().
It can therefore be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> (tpm_tis_isa)
Acked-by: Corey Minyard <cminyard@mvista.com> (isa_ipmi_bt, isa_ipmi_kcs)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220301220037.76555-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-14-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
The exynos4210_uart_post_load() function assumes that it is passed
the Exynos4210UartState, but it has been attached to the
VMStateDescription for the Exynos4210UartFIFO type. The result is a
SIGSEGV when attempting to load VM state for any machine type
including this device.
Fix the bug by attaching the post-load function to the VMSD for the
Exynos4210UartState. This is the logical place for it, because the
actions it does relate to the entire UART state, not just the FIFO.
Thanks to the bug reporter @TrungNguyen1909 for the clear bug
description and the suggested fix.
Fixes: c9d3396d80
("hw/char/exynos4210_uart: Implement post_load function")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/638
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120151648.433736-1-peter.maydell@linaro.org
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Fix issue where the data register may be overwritten by next character
reception before being read and returned.
Signed-off-by: Olivier Hériveaux <olivier.heriveaux@ledger.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211128120723.4053-1-olivier.heriveaux@ledger.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ESCC datasheet states that SPEC_ALLSENT is always set in sync mode and set
in async mode once all characters have cleared the transmitter. Since writes to
SERIAL_DATA use a synchronous chardev API, the guest can never see the state when
transmission is in progress so it is possible to set SPEC_ALLSENT in the
R_SPEC register unconditionally.
This fixes a hang when using the Sun PROM as it attempts to enumerate the
onboard serial devices, and a similar hang in OpenBSD SPARC32 where in both cases
the boot process will not proceed until SPEC_ALLSENT has been set after writing
to W_TXCTRL1.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211118181835.18497-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The "Transmit Interrupts and Transmit Buffer Empty Bit" section of the ESCC
datasheet states the following about the STATUS_TXEMPTY bit: "After a hardware
reset (including a hardware reset by software), or a channel reset, this bit
is set to 1".
Update escc_reset() to set the STATUS_TXEMPTY bit in the R_STATUS register
on device reset as described which fixes a regression whereby the Sun PROM
checks this bit early on startup and gets stuck in an infinite loop if it is
not set.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211118181835.18497-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Normally there are at least two sh_serial instances. Add device id to
trace messages to make it clear which instance they belong to
otherwise its not possible to tell which serial device is accessed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <cc1f9ff9f4259ae799750e452f8871849c7a104c.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <92902ba34fdf2c8c62232365fbb6531b1036d557.1635541329.git.balaton@eik.bme.hu>
[PMD: Use g_strdup() to initialize DeviceState::id]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of allocating timer with timer_new store it directly in the
state struct. This makes it simpler to free it together with the device.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <fd01eb3720ec32dab06e03019f72f3e177033679.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace fprintf with qemu_log_mask LOG_GUEST_ERROR as the intention is
to handle valid accesses in these functions so if we get to these
errors then it's an invalid access. Do not abort as that would allow
the guest to crash QEMU and the practice in other devices is to not do
that just log and ignore the invalid access. While at it also simplify
the complex bit ops to check if a return value was set which can be
done much simpler and clearer.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <6b46045141d6d9cc32e17c223896fa1116384796.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- Embed SerialMM in MchpPfSoCMMUartState and QOM-initialize it
- Alias SERIAL_MM 'chardev' property on MCHP_PFSOC_UART
- Forward SerialMM sysbus IRQ in mchp_pfsoc_mmuart_realize()
- Add DeviceReset() method
- Add vmstate structure for migration
- Register device in 'input' category
- Keep mchp_pfsoc_mmuart_create() behavior
Note, serial_mm_init() calls qdev_set_legacy_instance_id().
This call is only needed for backwards-compatibility of incoming
migration data with old versions of QEMU which implemented migration
of devices with hand-rolled code. Since this device didn't previously
handle migration at all, then it doesn't need to set the legacy
instance ID.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-4-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Our device have 2 different I/O regions:
- a 16550 UART mapped for 32-bit accesses
- 13 extra registers
Instead of mapping each region on the main bus, introduce
a container, map the 2 devices regions on the container,
and map the container on the main bus.
Before:
(qemu) info mtree
...
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-000000002010101f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-000000002010301f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-000000002010501f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-000000002010701f (prio 0, i/o): mchp.pfsoc.mmuart
After:
(qemu) info mtree
...
0000000020100000-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020102000-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020104000-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020106000-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210925133407.1259392-3-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current MCHP_PFSOC_MMUART_REG_SIZE definition represent the
size occupied by all the registers. However all registers are
32-bit wide, and the MemoryRegionOps handlers are restricted to
32-bit:
static const MemoryRegionOps mchp_pfsoc_mmuart_ops = {
.read = mchp_pfsoc_mmuart_read,
.write = mchp_pfsoc_mmuart_write,
.impl = {
.min_access_size = 4,
.max_access_size = 4,
},
Avoid being triskaidekaphobic, simplify by using the number of
registers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-2-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of sifive_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of shakti_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of ibex_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
We've got SW that expects FSBL (Bootlooader) to setup clocks and
resets. It's quite common that users run that SW on QEMU without
FSBL (FSBL typically requires the Xilinx tools installed). That's
fine, since users can stil use -device loader to enable clocks etc.
To help folks understand what's going, a log (guest-error) message
would be helpful here. In particular with the serial port since
things will go very quiet if they get things wrong.
Suggested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-7-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read or write to uart registers when unclocked or in reset should be
ignored. Add the check there, and as a result of this, the check in
uart_write_tx_fifo() is now unnecessary.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This converts uart_read() and uart_write() to memop_with_attrs() ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the clock/reset check is done in uart_receive(), but we
can move the check to uart_can_receive() which is earlier.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
