With the change, we extend the extent release mailbox command processing
to allow more flexible release. As long as the DPA range of the extent to
release is covered by accepted extent(s) in the device, the release can be
performed.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-14-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All DPA ranges in the DC regions are invalid to access until an extent
covering the range has been successfully accepted by the host. A bitmap
is added to each region to record whether a DC block in the region has
been backed by a DC extent. Each bit in the bitmap represents a DC block.
When a DC extent is accepted, all the bits representing the blocks in the
extent are set, which will be cleared when the extent is released.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-13-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To simulate FM functionalities for initiating Dynamic Capacity Add
(Opcode 5604h) and Dynamic Capacity Release (Opcode 5605h) as in CXL spec
r3.1 7.6.7.6.5 and 7.6.7.6.6, we implemented two QMP interfaces to issue
add/release dynamic capacity extents requests.
With the change, we allow to release an extent only when its DPA range
is contained by a single accepted extent in the device. That is to say,
extent superset release is not supported yet.
1. Add dynamic capacity extents:
For example, the command to add two continuous extents (each 128MiB long)
to region 0 (starting at DPA offset 0) looks like below:
{ "execute": "qmp_capabilities" }
{ "execute": "cxl-add-dynamic-capacity",
"arguments": {
"path": "/machine/peripheral/cxl-dcd0",
"host-id": 0,
"selection-policy": "prescriptive",
"region": 0,
"extents": [
{
"offset": 0,
"len": 134217728
},
{
"offset": 134217728,
"len": 134217728
}
]
}
}
2. Release dynamic capacity extents:
For example, the command to release an extent of size 128MiB from region 0
(DPA offset 128MiB) looks like below:
{ "execute": "cxl-release-dynamic-capacity",
"arguments": {
"path": "/machine/peripheral/cxl-dcd0",
"host-id": 0,
"removal-policy":"prescriptive",
"region": 0,
"extents": [
{
"offset": 134217728,
"len": 134217728
}
]
}
}
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-12-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per CXL spec 3.1, two mailbox commands are implemented:
Add Dynamic Capacity Response (Opcode 4802h) 8.2.9.9.9.3, and
Release Dynamic Capacity (Opcode 4803h) 8.2.9.9.9.4.
For the process of the above two commands, we use two-pass approach.
Pass 1: Check whether the input payload is valid or not; if not, skip
Pass 2 and return mailbox process error.
Pass 2: Do the real work--add or release extents, respectively.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-11-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add dynamic capacity extent list representative to the definition of
CXLType3Dev and implement get DC extent list mailbox command per
CXL.spec.3.1:.8.2.9.9.9.2.
Tested-by: Svetly Todorov <svetly.todorov@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-10-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add (file/memory backed) host backend for DCD. All the dynamic capacity
regions will share a single, large enough host backend. Set up address
space for DC regions to support read/write operations to dynamic capacity
for DCD.
With the change, the following support is added:
1. Add a new property to type3 device "volatile-dc-memdev" to point to host
memory backend for dynamic capacity. Currently, all DC regions share one
host backend;
2. Add namespace for dynamic capacity for read/write support;
3. Create cdat entries for each dynamic capacity region.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-9-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rename mem_size as static_mem_size for type3 memdev to cover static RAM and
pmem capacity, preparing for the introduction of dynamic capacity to support
dynamic capacity devices.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-6-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per cxl spec r3.1, add dynamic capacity (DC) region representative based on
Table 8-165 and extend the cxl type3 device definition to include DC region
information. Also, based on info in 8.2.9.9.9.1, add 'Get Dynamic Capacity
Configuration' mailbox support.
Note: we store region decode length as byte-wise length on the device, which
should be divided by 256 * MiB before being returned to the host
for "Get Dynamic Capacity Configuration" mailbox command per
specification.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-5-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Based on CXL spec r3.1 Table 8-127 (Identify Memory Device Output
Payload), dynamic capacity event log size should be part of
output of the Identify command.
Add dc_event_log_size to the output payload for the host to get the info.
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-4-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This enables wrapper devices to customize the base device's CCI
(for example, with custom commands outside the specification)
without the need to change the base device.
The also enabled the base device to dispatch those commands without
requiring additional driver support.
Heavily edited by Jonathan Cameron to increase code reuse
Signed-off-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-3-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows devices to have fully customized CCIs, along with complex
devices where wrapper devices can override or add additional CCI
commands without having to replicate full command structures or
pollute a base device with every command that might ever be used.
Signed-off-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20240523174651.1089554-2-nifan.cxl@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
With returned boolean, there's no need to dereference @errp to check
failure case.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-4-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
So make ct3_build_cdat() return boolean, and this is the preparation for
cxl_doe_cdat_init() returning boolean.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-3-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As error.h suggested, the best practice for callee is to return
something to indicate success / failure.
So make ct3_load_cdat() return boolean, and this is the preparation for
cxl_doe_cdat_init() returning boolean.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20240418100433.1085447-2-zhao1.liu@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
As the comment in qapi/error, dereferencing @errp requires
ERRP_GUARD():
* = Why, when and how to use ERRP_GUARD() =
*
* Without ERRP_GUARD(), use of the @errp parameter is restricted:
* - It must not be dereferenced, because it may be null.
...
* ERRP_GUARD() lifts these restrictions.
*
* To use ERRP_GUARD(), add it right at the beginning of the function.
* @errp can then be used without worrying about the argument being
* NULL or &error_fatal.
*
* Using it when it's not needed is safe, but please avoid cluttering
* the source with useless code.
But in cxl_fixed_memory_window_config(), @errp is dereferenced in 2
places without ERRP_GUARD():
fw->enc_int_ways = cxl_interleave_ways_enc(fw->num_targets, errp);
if (*errp) {
return;
}
and
fw->enc_int_gran =
cxl_interleave_granularity_enc(object->interleave_granularity,
errp);
if (*errp) {
return;
}
For the above 2 places, we check "*errp", because neither function
returns a suitable error code. And since machine_set_cfmw() - the caller
of cxl_fixed_memory_window_config() - doesn't get the NULL @errp
parameter as the "set" method of object property,
cxl_fixed_memory_window_config() hasn't triggered the bug that
dereferencing the NULL @errp.
To follow the requirement of @errp, add missing ERRP_GUARD() in
cxl_fixed_memory_window_config().
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20240223085653.1255438-2-zhao1.liu@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This CXL component isn't allowed to have a RAS capability.
Whilst this should be harmless as software is not expected to look
here, good to clean it up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240215155206.2736-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When setting GLIB_VERSION_MAX_ALLOWED to GLIB_VERSION_2_58 or higher
(which we'll certainly do in the not too distant future), glib adds
type safety checks to the g_steal_pointer() macro. This trigger an
error in the ct3_load_cdat() function: The local char *buf variable is
assigned to uint8_t *buf in CDATObject, i.e. a pointer of a different
type. Change the local variable to the same type as buf in CDATObject
to avoid the error.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst the reported version was 1 so there should be no changes,
a couple of fields (where the value 0 was valid) were not
defined. Make those explicit and update references to be based
on CXL r3.1.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of bringing all of CXL emulation inline with CXL r3.1.
No functional changes.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of standardizing the QEMU code on CXL r3.1.
No fuctional changes as everything added is optional and
it is set as not implemented.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
a NULL parameter is enough for a NULL MemoryRegionOps
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cache_mem_ops.{read,write}() interprets opaque as
CXLComponentState(cxl_cstate) instead of ComponentRegisters(cregs).
Fortunately, cregs is the first member of cxl_cstate, so their values are
the same.
Fixes: 9e58f52d3f ("hw/cxl/component: Introduce CXL components (8.1.x, 8.2.5)")
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the current mdev_reg_read() implementation, it consistently returns
that the Media Status is Ready (01b). This was fine until commit
25a52959f9 ("hw/cxl: Add support for device sanitation") because the
media was presumed to be ready.
However, as per the CXL 3.0 spec "8.2.9.8.5.1 Sanitize (Opcode 4400h)",
during sanitation, the Media State should be set to Disabled (11b). The
mentioned commit correctly sets it to Disabled, but mdev_reg_read()
still returns Media Status as Ready.
To address this, update mdev_reg_read() to read register values instead
of returning dummy values.
Note that __toggle_media() managed to not only write something
that no one read, it did it to the wrong register storage and
so changed the reported mailbox size which was definitely not
the intent. That gets fixed as a side effect of allocating
separate state storage for this register.
Fixes: commit 25a52959f9 ("hw/cxl: Add support for device sanitation")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Two functions were reported to have dead code, remove the bogus
branches altogether, as well as a misplaced qemu_log call.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The addition of the DCD support for CXL type-3 devices extended the CDAT
table large enough that the checksum being returned was incorrect.[1]
This was because the checksum value was using the header length field
rather than each of the 4 bytes of the length field. This was
previously not seen because the length of the CDAT data was less than
256 thus resulting in an equivalent checksum value.
Properly calculate the checksum for the CDAT header.
[1] https://lore.kernel.org/all/20231116-fix-cdat-devm-free-v1-1-b148b40707d7@intel.com/
Fixes: aba578bdac ("hw/cxl/cdat: CXL CDAT Data Object Exchange implementation")
Cc: Huai-Cheng Kuo <hchkuo@avery-design.com.tw>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callback for building CDAT tables may return negative error codes.
This was previously unhandled and will result in potentially huge
allocations later on in ct3_build_cdat()
Detect the negative error code and defer cdat building.
Fixes: f5ee7413d5 ("hw/mem/cxl-type3: Add CXL CDAT Data Object Exchange")
Cc: Huai-Cheng Kuo <hchkuo@avery-design.com.tw>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit was created with scripts/clean-includes.
All .c should include qemu/osdep.h first. The script performs three
related cleanups:
* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c already includes
it. Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
Drop these, too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
CONFIG_ALL is tricky to use and was ported over to Meson from the
recursive processing of Makefile variables. Meson sourcesets
however have all_sources() and all_dependencies() methods that
remove the need for it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: 388d6b574e "hw/cxl: Use switch statements for read and write of cachemem registers"
Fixes: 3314efd276 "hw/cxl/mbox: Add Physical Switch Identify command."
Fixes: 004e3a93b8 "hw/cxl: Add tunneled command support to mailbox for switch cci."
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This implementation of tunneling makes the choice that our Type 3 device is
a Logical Device (LD) of a Multi-Logical Device (MLD) that just happens to
only have one LD for now.
Tunneling is supported from a Switch Mailbox CCI (and shortly via MCTP over
I2C connected to the switch MCTP CCI) via an outer level to the FM owned LD
in the MLD Type 3 device. From there an inner tunnel may be used to access
particular LDs.
Protocol wise, the following is what happens in a real system but we
don't emulate the transports - just the destinations and the payloads.
( Host -> Switch Mailbox CCI - in band FM-API mailbox command
or
Host -> Switch MCTP CCI - MCTP over I2C using the CXL FM-API
MCTP Binding.
)
then (if a tunnel command)
Switch -> Type 3 FM Owned LD - MCTP over PCI VDM using the
CXL FM-API binding (addressed by switch port)
then (if unwrapped command also a tunnel command)
Type 3 FM Owned LD to LD0 via internal transport
(addressed by LD number)
or (added shortly)
Host to Type 3 FM Owned MCTP CCI - MCTP over I2C using the
CXL FM-API MCTP Binding.
then (if unwrapped comand is a tunnel comamnd)
Type 3 FM Owned LD to LD0 via internal transport.
(addressed by LD number)
It is worth noting that the tunneling commands over PCI VDM
presumably use the appropriate MCTP binding depending on opcode.
This may be the CXL FMAPI binding or the CXL Memory Device Binding.
Additional commands will need to be added to make this
useful beyond testing the tunneling works.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-18-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Needed to allow the santize comamnds to be tested with proposed Linux Kernel
support. Default value + no control of the security state will work for now.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-17-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For now, provide this command on type 3 main mailbox only.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-15-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make use of the background operations through the sanitize command, per CXL
3.0 specs. Traditionally run times can be rather long, depending on the
size of the media.
Estimate times based on:
https://pmem.io/documents/NVDIMM_DSM_Interface-V1.8.pdf
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-14-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notify when the background operation is done. Note that for now background
commands are only supported on the main Type 3 mailbox.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support background commands in the mailbox, and update
cmd_infostat_bg_op_sts() accordingly. This patch does not implement mbox
interrupts upon completion, so the kernel driver must rely on polling to
know when the operation is done.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-12-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add this command for both the Switch CCI in switch upstream ports.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-11-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable it for the switch CCI.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add this command that is only available via out of band CCIs. It replicates
information that can be discovered inband via PCI config space.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL switch CCIs were added in CXL r3.0. They are a PCI function,
identified by class code that provides a CXL mailbox (identical
to that previously defined for CXL type 3 memory devices) over which
various FM-API commands may be used. Whilst the intent of this
feature is enable switch control from a BMC attached to a switch
upstream port, it is also useful to allow emulation of this feature
on the upstream port connected to a host using the CXL devices as
this greatly simplifies testing.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By moving the parts of the mailbox command handling that are CCI type
specific out to the caller, make the main handling code generic. Rename it
to cxl_process_cci_message() to reflect this new generality.
Change the type3 mailbox handling (reused shortly for the switch
mailbox CCI) to take a snapshot of the mailbox input data rather
than operating on it in place. This reduces the chance of bugs
due to aliasing going forwars.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enables having multiple CCIs per devices. Each CCI (mailbox) has it's own
state and command list, so they can't share a single structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
New CCI types that will be supported shortly do not have a single buffer
used in both directions. As such, split it up. To avoid the complexities
of implementing all commands to handle potential aliasing, take a copy of
the input before use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023160806.13206-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Putting the pointer in the structure for command handling puts a single
variable element inside an otherwise constant structure. Move it out as
a directly passed variable and take the cxl_cmd structures constant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023160806.13206-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As _Static_assert is a declaration, it can't follow a label until C23.
Some older versions of GCC trip up on this one.
This check has no obvious purpose so just remove it.
Reported-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20231023140210.3089-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael Tsirkin observed that there were some unnecessarily
long lines in the CXL code in a recent review.
This patch is intended to rectify that where it does not
hurt readability.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Done to reduce line lengths where this is used.
Ext seems sufficiently obvious that it need not be spelt out
fully.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Establishing that only register accesses of size 4 and 8 can occur
using these functions requires looking at their callers. Make it
easier to see that by using switch statements.
Assertions are used to enforce that the register storage is of the
matching size, allowing fixed values to be used for divisors of
the array indices.
Suggested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Bring this read function inline with the others that do
check for unexpected size values.
Also reduces line lengths to sub 80 chars.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Message-Id: <20231023140210.3089-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rename the version not burried in the macro to cap_h.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-ID: <20230925152258.5444-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
