- ePMP CSR address updates
- Convert internal interrupts to use QEMU GPIO lines
- SiFive PWM support
- Support for RISC-V ACLINT
- SiFive PDMA fixes
- Update to u-boot instructions for sifive_u
- mstatus.SD bug fix for hypervisor extensions
- OpenTitan fix for USB dev address
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmFJgSoACgkQIeENKd+X
cFQTOwf8DC7rBqOWQS3v/r+H2hlfDqW+4G3pPPBcoyCEiqO+cL26ox+EmTHDbieh
+0yWyp7L6SU/zcJ86oBAFNGH46ltXuUKOYWhkfA1QwlGzAwjZ82hnZ3jJqXf1jin
Wq0ElzKk6rvcRkHTVhdjkGvoxskaXPQ/kFzyTHrxMDlkmHO3L4IaYe0xsamRI11D
E7UJC97YmpSAsCNUc5irpkeLyiFobyR8TEL3nBEPK/6Xj0ojRT4zoGe1EotC7+sN
zL8a9ZuU0bL3rQH8Ai7wnXBP8D2PQa0tZQV6wne/BzeEUSpKrC/rGW73vQCz0Pps
U8VNkIlbAqD1s6aXlqE24H535x10Mw==
=WYF5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair23/tags/pull-riscv-to-apply-20210921' into staging
Second RISC-V PR for QEMU 6.2
- ePMP CSR address updates
- Convert internal interrupts to use QEMU GPIO lines
- SiFive PWM support
- Support for RISC-V ACLINT
- SiFive PDMA fixes
- Update to u-boot instructions for sifive_u
- mstatus.SD bug fix for hypervisor extensions
- OpenTitan fix for USB dev address
# gpg: Signature made Mon 20 Sep 2021 11:52:26 PM PDT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair23/tags/pull-riscv-to-apply-20210921: (21 commits)
hw/riscv: opentitan: Correct the USB Dev address
target/riscv: csr: Rename HCOUNTEREN_CY and friends
target/riscv: Backup/restore mstatus.SD bit when virtual register swapped
docs/system/riscv: sifive_u: Update U-Boot instructions
hw/dma: sifive_pdma: don't set Control.error if 0 bytes to transfer
hw/dma: sifive_pdma: allow non-multiple transaction size transactions
hw/dma: sifive_pdma: claim bit must be set before DMA transactions
hw/dma: sifive_pdma: reset Next* registers when Control.claim is set
hw/riscv: virt: Add optional ACLINT support to virt machine
hw/riscv: virt: Re-factor FDT generation
hw/intc: Upgrade the SiFive CLINT implementation to RISC-V ACLINT
hw/intc: Rename sifive_clint sources to riscv_aclint sources
sifive_u: Connect the SiFive PWM device
hw/timer: Add SiFive PWM support
hw/intc: ibex_timer: Convert the timer to use RISC-V CPU GPIO lines
hw/intc: sifive_plic: Convert the PLIC to use RISC-V CPU GPIO lines
hw/intc: ibex_plic: Convert the PLIC to use RISC-V CPU GPIO lines
hw/intc: sifive_clint: Use RISC-V CPU GPIO lines
target/riscv: Expose interrupt pending bits as GPIO lines
target/riscv: Fix satp write
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Setting Control.claim clears all of the chanel's Next registers.
This is effective only when Control.claim is set from 0 to 1.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Tested-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210912130553.179501-2-frank.chang@sifive.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate ACLINT devices only when "aclint=on"
parameter is passed along with machine name in QEMU command-line.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-5-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We re-factor and break the FDT generation into smaller functions
so that it is easier to modify FDT generation for different
configurations of virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-4-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V ACLINT is more modular and backward compatible with
original SiFive CLINT so instead of duplicating the original
SiFive CLINT implementation we upgrade the current SiFive CLINT
implementation to RISC-V ACLINT implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-3-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We will be upgrading SiFive CLINT implementation into RISC-V ACLINT
implementation so let's first rename the sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is the initial commit of the SiFive PWM timer. This is used by
guest software as a timer and is included in the SiFive FU540 SoC.
Signed-off-by: Justin Restivo <jrestivo@draper.com>
Signed-off-by: Alexandra Clifford <aclifford@draper.com>
Signed-off-by: Amanda Strnad <astrnad@draper.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 9f70a210acbfaf0e1ea6ad311ab892ac69134d8b.1631159656.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 84d5b1d5783d2e79eee69a2f7ac480cc0c070db3.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 0364190bfa935058a845c0fa1ecf650328840ad5.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 0a76946981852f5bd15f0c37ab35b253371027a8.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer and soft MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Message-id: 946e1ef5e268b24084c7ddad84c146de62a56736.1630301632.git.alistair.francis@wdc.com
During sbsa acs level 3 testing, it is seen that the GIC maintenance
interrupts are not triggered and the related test cases fail. This
is because we were incorrectly passing the value of the MISR register
(from maintenance_interrupt_state()) to qemu_set_irq() as the level
argument, whereas the device on the other end of this irq line
expects a 0/1 value.
Fix the logic to pass a 0/1 level indication, rather than a
0/not-0 value.
Fixes: c5fc89b36c ("hw/intc/arm_gicv3: Implement gicv3_cpuif_virt_update()")
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210915205809.59068-1-shashi.mallela@linaro.org
[PMM: tweaked commit message; collapsed nested if()s into one]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
UART5 is typically used as the default debug UART on the AST2600, but
UART1 is also designed to be a debug UART. All the AST2600 UART's have
semi-configurable clock rates through registers in the System Control
Unit (SCU), but only UART5 works out of the box with zero-initialized
values. The rest of the UART's expect a few of the registers to be
initialized to non-zero values, or else the clock rate calculation will
yield zero or undefined (due to a divide-by-zero).
For reference, the U-Boot clock rate driver here shows the calculation:
https://github.com/facebook/openbmc-uboot/blob/15f7e0dc01d8/drivers/clk/aspeed/clk_ast2600.c#L357
To summarize, UART5 allows selection from 4 rates: 24 MHz, 192 MHz, 24 /
13 MHz, and 192 / 13 MHz. The other UART's allow selecting either the
"low" rate (UARTCLK) or the "high" rate (HUARTCLK). UARTCLK and HUARTCLK
are configurable themselves:
UARTCLK = UXCLK * R / (N * 2)
HUARTCLK = HUXCLK * HR / (HN * 2)
UXCLK and HUXCLK are also configurable, and depend on the APLL and/or
HPLL clock rates, which also derive from complicated calculations. Long
story short, there's lots of multiplication and division from
configurable registers, and most of these registers are zero-initialized
in QEMU, which at best is unexpected and at worst causes this clock rate
driver to hang from divide-by-zero's. This can also be difficult to
diagnose, because it may cause U-Boot to hang before serial console
initialization completes, requiring intervention from gdb.
This change just initializes all of these registers with default values
from the datasheet.
To test this, I used Facebook's AST2600 OpenBMC image for "fuji", with
the following diff applied (because fuji uses UART1 for console output,
not UART5).
@@ -323,8 +323,8 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
}
/* UART - attach an 8250 to the IO space as our UART5 */
- serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART5], 2,
- aspeed_soc_get_irq(s, ASPEED_DEV_UART5),
+ serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART1], 2,
+ aspeed_soc_get_irq(s, ASPEED_DEV_UART1),
38400, serial_hd(0), DEVICE_LITTLE_ENDIAN);
/* I2C */
Without these clock rate registers being initialized, U-Boot hangs in
the clock rate driver from a divide-by-zero, because the UART1 clock
rate register reads return zero, and there's no console output. After
initializing them with default values, fuji boots successfully.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg: Removed _PARAM suffix ]
Message-Id: <20210906134023.3711031-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There was a bit of a thinko in the state calculation where every odd pin
in was reported in e.g. "pwm0" mode rather than "off". This was the
result of an incorrect bit shift for the 2-bit field representing each
LED state.
Fixes: a90d8f8467 ("misc/pca9552: Add qom set and get")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210723043624.348158-1-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are two GPIO controllers in the ast2600; one is 3.3V and the other
is 1.8V.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210713065854.134634-4-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There's no need to define the registers relative to the 0x800 offset
where the controller is mapped, as the device is instantiated as it's
own model at the correct memory address.
Simplify the defines and remove the offset to save future confusion.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210713065854.134634-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The logic in the handling for the control register required toggling the
enable state for writes to stick. Rework the condition chain to allow
sequential writes that do not update the enable state.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While some of the critical fields remain the same, there is variation in
the definition of the control register across the SoC generations.
Reserved regions are adjusted, while in other cases the mutability or
behaviour of fields change.
Introduce a callback to sanitize the value on writes to ensure model
behaviour reflects the hardware.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When mergeable buffer is enabled, we try to set the num_buffers after
the virtqueue elem has been unmapped. This will lead several issues,
E.g a use after free when the descriptor has an address which belongs
to the non direct access region. In this case we use bounce buffer
that is allocated during address_space_map() and freed during
address_space_unmap().
Fixing this by storing the elems temporarily in an array and delay the
unmap after we set the the num_buffers.
This addresses CVE-2021-3748.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: fbe78f4f55 ("virtio-net support")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Adding this callback provides a way to resume the processing of
cmds in fenceq and cmdq that were not processed because the UI
was waiting on a fence and blocked cmd processing.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-6-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create sync objects and fences only for dmabufs that are blobs. Once a
fence is created (after glFlush) and is signalled,
graphic_hw_gl_flushed() will be called and virtio-gpu cmd processing
will be resumed.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* mark MPS2/MPS3 board-internal i2c buses as 'full' so that command
line user-created devices are not plugged into them
* Take an exception if PSTATE.IL is set
* Support an emulated ITS in the virt board
* Add support for kudo-bmc board
* Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
* cadence_uart: Fix clock handling issues that prevented
u-boot from running
-----BEGIN PGP SIGNATURE-----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=7BH/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210913-3' into staging
target-arm queue:
* mark MPS2/MPS3 board-internal i2c buses as 'full' so that command
line user-created devices are not plugged into them
* Take an exception if PSTATE.IL is set
* Support an emulated ITS in the virt board
* Add support for kudo-bmc board
* Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
* cadence_uart: Fix clock handling issues that prevented
u-boot from running
# gpg: Signature made Mon 13 Sep 2021 21:04:52 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210913-3: (23 commits)
hw/arm/mps2.c: Mark internal-only I2C buses as 'full'
hw/arm/mps2-tz.c: Mark internal-only I2C buses as 'full'
hw/arm/mps2-tz.c: Add extra data parameter to MakeDevFn
qdev: Support marking individual buses as 'full'
target/arm: Merge disas_a64_insn into aarch64_tr_translate_insn
target/arm: Take an exception if PSTATE.IL is set
tests/data/acpi/virt: Update IORT files for ITS
hw/arm/virt: add ITS support in virt GIC
tests/data/acpi/virt: Add IORT files for ITS
hw/intc: GICv3 redistributor ITS processing
hw/intc: GICv3 ITS Feature enablement
hw/intc: GICv3 ITS Command processing
hw/intc: GICv3 ITS command queue framework
hw/intc: GICv3 ITS register definitions added
hw/intc: GICv3 ITS initial framework
hw/arm: Add support for kudo-bmc board.
hw/arm/virt: KVM: Probe for KVM_CAP_ARM_VM_IPA_SIZE when creating scratch VM
hw/char: cadence_uart: Log a guest error when device is unclocked or in reset
hw/char: cadence_uart: Ignore access when unclocked or in reset for uart_{read, write}()
hw/char: cadence_uart: Convert to memop_with_attrs() ops
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The various MPS2 boards implemented in mps2.c have multiple I2C
buses: a bus dedicated to the audio configuration, one for the LCD
touchscreen controller, and two which are connected to the external
Shield expansion connector. Mark the buses which are used only for
board-internal devices as 'full' so that if the user creates i2c
devices on the commandline without specifying a bus name then they
will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-5-peter.maydell@linaro.org
The various MPS2 boards have multiple I2C buses: typically a bus
dedicated to the audio configuration, one for the LCD touchscreen
controller, one for a DDR4 EEPROM, and two which are connected to the
external Shield expansion connector. Mark the buses which are used
only for board-internal devices as 'full' so that if the user creates
i2c devices on the commandline without specifying a bus name then
they will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-4-peter.maydell@linaro.org
The mps2-tz boards use a data-driven structure to create the devices
that sit behind peripheral protection controllers. Currently the
functions which create these devices are passed an 'opaque' pointer
which is always the address within the machine struct of the device
to create, and some "all devices need this" information like irqs and
addresses.
If a specific device needs more information than this, it is
currently not possible to pass that through from the PPCInfo
data structure. Add support for passing an extra data parameter,
so that we can more flexibly handle the needs of specific
device types. To provide some type-safety we make this extra
parameter a pointer to a union (which initially has no members).
In particular, we would like to be able to indicate which of the
i2c controllers are for on-board devices only and which are
connected to the external 'shield' expansion port; a subsequent
patch will use this mechanism for that purpose.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-3-peter.maydell@linaro.org
Included creation of ITS as part of virt platform GIC
initialization. This Emulated ITS model now co-exists with kvm
ITS and is enabled in absence of kvm irq kernel support in a
platform.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-9-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implemented lpi processing at redistributor to get lpi config info
from lpi configuration table,determine priority,set pending state in
lpi pending table and forward the lpi to cpuif.Added logic to invoke
redistributor lpi processing with translated LPI which set/clear LPI
from ITS device as part of ITS INT,CLEAR,DISCARD command and
GITS_TRANSLATER processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-7-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added properties to enable ITS feature and define qemu system
address space memory in gicv3 common,setup distributor and
redistributor registers to indicate LPI support.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-6-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added ITS command queue handling for MAPTI,MAPI commands,handled ITS
translation which triggers an LPI via INT command as well as write
to GITS_TRANSLATER register,defined enum to differentiate between ITS
command interrupt trigger and GITS_TRANSLATER based interrupt trigger.
Each of these commands make use of other functionalities implemented to
get device table entry,collection table entry or interrupt translation
table entry required for their processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-5-shashi.mallela@linaro.org
[PMM: use INTERRUPT for ItsCmdType enum name to avoid
conflict with INT type defined by Windows headers]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added functionality to trigger ITS command queue processing on
write to CWRITE register and process each command queue entry to
identify the command type and handle commands like MAPD,MAPC,SYNC.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-4-shashi.mallela@linaro.org
[PMM: fixed format string nit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
