Hardware of sbsa-ref board is nowadays defined by both BSA and SBSA
specifications. Then BBR defines firmware interface.
Added note about DeviceTree data passed from QEMU to firmware. It is
very minimal and provides only data we use in firmware.
Added NUMA information to list of things reported by DeviceTree.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20240328163851.1386176-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Leif Lindholm <quic_llindhol@quicinc.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain
Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable all FEAT_ECV features on the 'max' CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240301183219.2424889-9-peter.maydell@linaro.org
Add the necessary files to add a simple RCC implementation with just
reads from and writes to registers. Also instantiate the RCC in the
STM32L4x5_SoC. It is needed for accurate emulation of all the SoC
clocks and timers.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-2-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few deficiencies in the current device model need to be noted.
1. FIFOs are not used. All sends and receives are done directly.
2. Repeated starts are not emulated. Repeated starts can be triggered in real
hardware by sending a new read transfer request in the window time between
transfer active set of write transfer request and done bit set of the same.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240224191038.2409945-2-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-42-sergey.kambalin@auriga.com
[PMM: list PCIE and GENET as 'missing' for now, until we land
the patches which add those devices]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add documentation for the mps3-an536 board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-14-peter.maydell@linaro.org
This patch adds the SPI controller for the BCM2835. Polling and interrupt modes
of transfer are supported. DMA and LoSSI modes are currently unimplemented.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Message-id: 20240129221807.2983148-2-rayhan.faizel@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a note on CPU features that are off by default in `virt` machines.
Some CPU features will remain off even if a CPU-capable CPU (e.g.,
`-cpu max`) is selected because they require support in both the CPU
itself and in the wider system. Therefore, the user, besides selecting a
CPU that supports such features, must also turn on the feature using a
machine option.
Signed-off-by: Gustavo Romero <gustavo.romero@linaro.org>
Message-id: 20240122211215.95073-1-gustavo.romero@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add watchdog timer support to Allwinner-H40 and Bananapi.
The watchdog timer is added as an overlay to the Timer
module memory map.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Message-id: 20240115182757.1095012-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports an AHCI compliant SATA controller.
Add support for it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240115182757.1095012-3-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 supports two USB host ports shared between a USB 2.0 EHCI
host controller and a USB 1.1 OHCI host controller. Add support for both
of them.
If machine USB support is not enabled, create unimplemented devices
for the USB memory ranges to avoid crashes when booting Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240115182757.1095012-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Although very similar to the STM32F4xx EXTI, STM32L4x5 EXTI generates
more than 32 event/interrupt requests and thus uses more registers
than STM32F4xx EXTI which generates 23 event/interrupt requests.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240109160658.311932-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Improve the 'highmem' option docs to note that by default we assume
that a 32-bit kernel on an LPAE-capable CPU has LPAE enabled, and
what the consequences are.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20240109170834.1387457-1-peter.maydell@linaro.org
Enable FEAT_NV2 on the 'max' CPU, and stop filtering it out for
the Neoverse N2 and Neoverse V1 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
Enable FEAT_NV on the 'max' CPU, and stop filtering it out for the
Neoverse N2 and Neoverse V1 CPUs. We continue to downgrade FEAT_NV2
support to FEAT_NV for the latter two CPU types.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Miguel Luis <miguel.luis@oracle.com>
This commit adds a new B-L475E-IOT01A board using the STM32L475VG SoC
as well as a dedicated documentation file.
The implementation is derived from the Netduino Plus 2 machine.
There are no peripherals implemented yet, only memory regions.
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240108135849.351719-3-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If "busses" might be encountered as a plural of "bus" (5 instances),
the correct spelling is "buses" (26 instances). Fixing those 5
instances makes the doc more consistent.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
QOM type names containing ',' result in awful UI. We got rid of them
in v6.0.0 (commit e178113ff6 hw: Replace anti-social QOM type names).
A few have crept back since:
xlnx,cframe-reg
xlnx,efuse
xlnx,pmc-efuse-cache
xlnx,versal-cfu-apb
xlnx,versal-cfu-fdro
xlnx,versal-cfu-sfr
xlnx,versal-crl
xlnx,versal-efuse
xlnx,zynqmp-efuse
These are all device types. They can't be plugged with -device /
device_add, except for "xlnx,efuse" (I'm not sure that one is
intentional).
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-aarch64 -device xlnx,,pmc-efuse-cache,help
They can also be used with -global, where you must *not* double the
comma:
$ qemu-system-aarch64 -global xlnx,efuse.drive-index=2
Trap for the unwary.
"xlnx,efuse", "xlnx,versal-efuse", "xlnx,pmc-efuse-cache",
"xlnx-zynqmp-efuse" are from v6.2.0, "xlnx,versal-crl" is from v7.1.0,
and the remainder are new.
Rename them all to "xlnx-FOO", like commit e178113ff6 did.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-ID: <20231117114457.177308-3-thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Fixes: b65b4b7ae3 (xlnx-bbram: hw/nvram: Use dot in device type name)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[thuth: Use longhand syntax to avoid problems with the "." in the name]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-ID: <20231117114457.177308-2-thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I noticed the code blocks where not rendering properly so thought I'd
better fix things up. So:
- Use better title for the machine type
- Explain why Xen is a little different
- Add a proper anchor to the tpm-device link
- add newline so code block properly renders
- add some indentation to make continuation clearer
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20231207130623.360473-1-alex.bennee@linaro.org>
On the vexpress-a9 board we try to map both RAM and flash to address 0,
as seen in "info mtree":
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-0000000003ffffff (prio 0, romd): alias vexpress.flashalias @vexpress.flash0 0000000000000000-0000000003ffffff
0000000000000000-0000000003ffffff (prio 0, ram): alias vexpress.lowmem @vexpress.highmem 0000000000000000-0000000003ffffff
0000000010000000-0000000010000fff (prio 0, i/o): arm-sysctl
0000000010004000-0000000010004fff (prio 0, i/o): pl041
(etc)
The flash "wins" and the RAM mapping is useless (but also harmless).
This happened as a result of commit 6ec1588e in 2014, which changed
"we always map the RAM to the low addresses for vexpress-a9" to "we
always map flash in the low addresses", but forgot to stop mapping
the RAM.
In real hardware, this low part of memory is remappable, both at
runtime by the guest writing to a control register, and configurably
as to what you get out of reset -- you can have the first flash
device, or the second, or the DDR2 RAM, or the external AXI bus
(which for QEMU means "nothing there"). In an ideal world we would
support that remapping both at runtime and via a machine property to
select the out-of-reset behaviour.
Pending anybody caring enough to implement the full remapping
behaviour:
* remove the useless mapped-but-inaccessible lowram MR
* document that QEMU doesn't support remapping of low memory
Fixes: 6ec1588e ("hw/arm/vexpress: Alias NOR flash at 0 for vexpress-a9")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1761
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231103185602.875849-1-peter.maydell@linaro.org
Implement a model of the Neoverse N2 CPU. This is an Armv9.0-A
processor very similar to the Cortex-A710. The differences are:
* no FEAT_EVT
* FEAT_DGH (data gathering hint)
* FEAT_NV (not yet implemented in QEMU)
* Statistical Profiling Extension (not implemented in QEMU)
* 48 bit physical address range, not 40
* CTR_EL0.DIC = 1 (no explicit icache cleaning needed)
* PMCR_EL0.N = 6 (always 6 PMU counters, not 20)
Because it has 48-bit physical address support, we can use
this CPU in the sbsa-ref board as well as the virt board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230915185453.1871167-3-peter.maydell@linaro.org
FEAT_HPMN0 is a small feature which defines that it is valid for
MDCR_EL2.HPMN to be set to 0, meaning "no PMU event counters provided
to an EL1 guest" (previously this setting was reserved). QEMU's
implementation almost gets HPMN == 0 right, but we need to fix
one check in pmevcntr_is_64_bit(). That is enough for us to
advertise the feature in the 'max' CPU.
(We don't need to make the behaviour conditional on feature
presence, because the FEAT_HPMN0 behaviour is within the range
of permitted UNPREDICTABLE behaviour for a non-FEAT_HPMN0
implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230921185445.3339214-1-peter.maydell@linaro.org
Enable FEAT_MOPS on the AArch64 'max' CPU, and add it to
the list of features we implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230912140434.1333369-13-peter.maydell@linaro.org
FEAT_HBC (Hinted conditional branches) provides a new instruction
BC.cond, which behaves exactly like the existing B.cond except
that it provides a hint to the branch predictor about the
likely behaviour of the branch.
Since QEMU does not implement branch prediction, we can treat
this identically to B.cond.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230831232441.66020-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cortex-a710 is a first generation ARMv9.0-A processor.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230831232441.66020-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the QARMA3 cryptographic algorithm for PAC calculation.
Implement a cpu feature to select the algorithm and document it.
Signed-off-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230829232335.965414-6-richard.henderson@linaro.org
Message-Id: <20230609172324.982888-4-aaron@os.amperecomputing.com>
[rth: Merge cpu feature addition from another patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the -nodefaults option is set, flash devices should be created
with :
-blockdev node-name=fmc0,driver=file,filename=./flash.img \
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0 \
To be noted that in this case, the ROM will not be installed and the
initial boot sequence (U-Boot loading) will fetch instructions using
SPI transactions which is significantly slower. That's exactly how HW
operates though.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a mandatory feature for Armv8.1 architectures but we don't
state the feature clearly in our emulation list. Also include
FEAT_CRC32 comment in aarch64_max_tcg_initfn for ease of grepping.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230824075406.1515566-1-alex.bennee@linaro.org
Cc: qemu-stable@nongnu.org
Message-Id: <20230222110104.3996971-1-alex.bennee@linaro.org>
[PMM: pluralize 'instructions' in docs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This feature allows the operating system to set TCR_ELx.HWU*
to allow the implementation to use the PBHA bits from the
block and page descriptors for for IMPLEMENTATION DEFINED
purposes. Since QEMU has no need to use these bits, we may
simply ignore them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we have implemented support for FEAT_LSE2, we can define
a CPU model for the Neoverse-V1, and enable it for the virt and
sbsa-ref boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230704130647.2842917-3-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The current sbsa-ref cannot use EHCI controller which is only
able to do 32-bit DMA, since sbsa-ref doesn't have RAM below 4GB.
Hence, this uses XHCI to provide a usb controller with 64-bit
DMA capablity instead of EHCI.
We bump the platform version to 0.3 with this change. Although the
hardware at the USB controller address changes, the firmware and
Linux can both cope with this -- on an older non-XHCI-aware
firmware/kernel setup the probe routine simply fails and the guest
proceeds without any USB. (This isn't a loss of functionality,
because the old USB controller never worked in the first place.) So
we can call this a backwards-compatible change and only bump the
minor version.
Signed-off-by: Yuquan Wang <wangyuquan1236@phytium.com.cn>
Message-id: 20230621103847.447508-2-wangyuquan1236@phytium.com.cn
[PMM: tweaked commit message; add line to docs about what
changes in platform version 0.3]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create ITS as part of SBSA platform GIC initialization.
GIC ITS information is in DeviceTree so TF-A can pass it to EDK2.
Bumping platform version to 0.2 as this is important hardware change.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230619170913.517373-2-marcin.juszkiewicz@linaro.org
Co-authored-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230622143046.1578160-1-richard.henderson@linaro.org
[PMM: fixed typo; note experimental status in emulation.rst too]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We plan to add more hardware information into DeviceTree to limit amount
of hardcoded values in firmware.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-id: 20230531171834.236569-1-marcin.juszkiewicz@linaro.org
[PMM: fix format nits, add text about platform version fields from
a comment in the C source file]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=543t
-----END PGP SIGNATURE-----
Merge tag 'xenpvh5-tag' of https://gitlab.com/sstabellini/qemu into staging
xenpvh5
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEE0E4zq6UfZ7oH0wrqiU+PSHDhrpAFAmSLo0QACgkQiU+PSHDh
# rpB1Gw/9H5Cx7wQZVyKfFwnyOoP2QTedCISxC0HL5qFmUGcJY21gXaJZ10JaU/HM
# zHEJj2M17EgVCTkZVqZeKuj+nzyjbRKatT3YmFqKqFNNt5M1yQxC9BfVgso4PND/
# SY0/8BvqumgJEqD3sf76KbQAILKwahPtA42LTM7S7r2ZsmQpvmOpdOhCVugpnqs/
# FheP8N6hdlZ7GnRGtXv9QnKxMVThuE3mRCUWCyYsV/Roz6uvPsvskrdSeC3LzzBd
# Ewq56vB+qQg+WbNTgK2BcVOzV/89k9tjWsUnamfhjD2lUxfHrne1FBclhKMcHhUv
# T53zjhxjlRfmzUxC4917Krt4Tw/AaDW7v1pn6RokUq5U059Wb8q0IjzL75FOeD3o
# e9DNp+RR8py44ejfi2WHR7jqayMPVIO86uJ3usshiZ9YgK5efFAtlwN/KNR5JX8k
# Y1BR9O8BebtRymljtiLWUFXlu3xywGSA23KotT7XtzXKEaTZkIHdI395YKksYPkG
# pil0C0bh5ZW3ZWd4M/CNcVOb69R53p15O77mjmKtjnkQYJAPD6Kbc9thZ1zdWwPR
# ivFPdiTJb0FElS0ywZwezKYRKXje6E9ejXgAzgFuZI/rFdeO0HfkifiNoro1NAxK
# g4V+LE5oPt09GpL2nuHrh/y9g9MnLlXyNBhPV0CRelU6fPKIk1w=
# =543t
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 16 Jun 2023 01:48:20 AM CEST
# gpg: using RSA key D04E33ABA51F67BA07D30AEA894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <sstabellini@kernel.org>" [unknown]
# gpg: aka "Stefano Stabellini <stefano.stabellini@eu.citrix.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* tag 'xenpvh5-tag' of https://gitlab.com/sstabellini/qemu:
test/qtest: add xepvh to skip list for qtest
meson.build: enable xenpv machine build for ARM
hw/arm: introduce xenpvh machine
meson.build: do not set have_xen_pci_passthrough for aarch64 targets
hw/xen/xen-hvm-common: Use g_new and error_report
hw/xen/xen-hvm-common: skip ioreq creation on ioreq registration failure
include/hw/xen/xen_common: return error from xen_create_ioreq_server
xen-hvm: reorganize xen-hvm and move common function to xen-hvm-common
hw/i386/xen/xen-hvm: move x86-specific fields out of XenIOState
hw/i386/xen: rearrange xen_hvm_init_pc
hw/i386/xen/: move xen-mapcache.c to hw/xen/
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a new machine xenpvh which creates a IOREQ server to register/connect with
Xen Hypervisor.
Optional: When CONFIG_TPM is enabled, it also creates a tpm-tis-device, adds a
TPM emulator and connects to swtpm running on host machine via chardev socket
and support TPM functionalities for a guest domain.
Extra command line for aarch64 xenpvh QEMU to connect to swtpm:
-chardev socket,id=chrtpm,path=/tmp/myvtpm2/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-machine tpm-base-addr=0x0c000000 \
swtpm implements a TPM software emulator(TPM 1.2 & TPM 2) built on libtpms and
provides access to TPM functionality over socket, chardev and CUSE interface.
Github repo: https://github.com/stefanberger/swtpm
Example for starting swtpm on host machine:
mkdir /tmp/vtpm2
swtpm socket --tpmstate dir=/tmp/vtpm2 \
--ctrl type=unixio,path=/tmp/vtpm2/swtpm-sock &
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Most of the Aspeed machines use the UART5 device for the boot console,
and QEMU connects the first serial Chardev to this SoC device for this
purpose. See routine connect_serial_hds_to_uarts().
Nevertheless, some machines use another boot console, such as the fuji,
and commit 5d63d0c76c ("hw/arm/aspeed: Allow machine to set UART
default") introduced a SoC class attribute 'uart_default' and property
to be able to change the boot console device. It was later changed by
commit d2b3eaefb4 ("aspeed: Refactor UART init for multi-SoC machines").
The "bmc-console" machine option goes a step further and lets the user define
the UART device from the QEMU command line without introducing a new
machine definition. For instance, to use device UART3 (mapped on
/dev/ttyS2 under Linux) instead of the default UART5, one would use :
-M ast2500-evb,bmc-console=uart3
Cc: Abhishek Singh Dagur <abhishek@drut.io>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230530191438.411344-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add documents for Banana Pi M2U
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
[PMM: Minor format fixes to correct sphinx errors]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CANFD0 and CANFD1 on the Versal-virt machine and update xlnx-versal-virt
document with CANFD command line examples.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We moved from VGA to Bochs to have PCIe card.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
FEAT_PAN3 adds an EPAN bit to SCTLR_EL1 and SCTLR_EL2, which allows
the PAN bit to make memory non-privileged-read/write if it is
user-executable as well as if it is user-read/write.
Implement this feature and enable it in the AArch64 'max' CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230331145045.2584941-4-peter.maydell@linaro.org
