Introduce the PEXTUW opcode (Parallel Extend Upper from Word).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210309145653.743937-12-f4bug@amsat.org>
Rather than using the magic 0x80000000 number for the PCI I/O BAR
physical address on the main system bus, use a definition.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210417103028.601124-6-f4bug@amsat.org>
The ASIC PCI bridge chipset from Motorola is named 'Raven'.
This chipset is used in the PowerPC Reference Platform (PReP),
but not restricted to it. Rename it accordingly.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210417103028.601124-5-f4bug@amsat.org>
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
-----BEGIN PGP SIGNATURE-----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=8708
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging
Some qemu updates for IPMI and I2C
Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.
Add support for I2C PMBus devices.
Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.
Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.
# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81
* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Make blockdev-reopen stable
- Remove deprecated qemu-img backing file without format
- rbd: Convert to coroutines and add write zeroes support
- rbd: Updated MAINTAINERS
- export/fuse: Allow other users access to the export
- vhost-user: Fix backends without multiqueue support
- Fix drive-backup transaction endless drained section
-----BEGIN PGP SIGNATURE-----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=kH+r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
- Make blockdev-reopen stable
- Remove deprecated qemu-img backing file without format
- rbd: Convert to coroutines and add write zeroes support
- rbd: Updated MAINTAINERS
- export/fuse: Allow other users access to the export
- vhost-user: Fix backends without multiqueue support
- Fix drive-backup transaction endless drained section
# gpg: Signature made Fri 09 Jul 2021 13:49:22 BST
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (28 commits)
block: Make blockdev-reopen stable API
iotests: Test reopening multiple devices at the same time
block: Support multiple reopening with x-blockdev-reopen
block: Acquire AioContexts during bdrv_reopen_multiple()
block: Add bdrv_reopen_queue_free()
qcow2: Fix dangling pointer after reopen for 'file'
qemu-img: Improve error for rebase without backing format
qemu-img: Require -F with -b backing image
qcow2: Prohibit backing file changes in 'qemu-img amend'
blockdev: fix drive-backup transaction endless drained section
vhost-user: Fix backends without multiqueue support
MAINTAINERS: add block/rbd.c reviewer
block/rbd: fix type of task->complete
iotests/fuse-allow-other: Test allow-other
iotests/308: Test +w on read-only FUSE exports
export/fuse: Let permissions be adjustable
export/fuse: Give SET_ATTR_SIZE its own branch
export/fuse: Add allow-other option
export/fuse: Pass default_permissions for mount
util/uri: do not check argument of uri_free()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's a (probably) final pull request before the qemu-6.1 soft
freeze. Includes:
* Implementation of the new H_RPT_INVALIDATE hypercall
* Virtual Open Firmware for pSeries and pegasos2 machine types.
This is an experimental minimal Open Firmware implementation which
works by delegating nearly everything to qemu itself via a special
hypercall.
* A number of cleanups to the ppc soft MMU code
* Fix to handling of two-level radix mode translations for the
powernv machine type
* Update the H_GET_CPU_CHARACTERISTICS call with newly defined bits.
This will allow more flexible handling of possible future CPU
Spectre-like flaws
* Correctly treat mtmsrd as an illegal instruction on BookE cpus
* Firmware update for the ppce500 machine type
-----BEGIN PGP SIGNATURE-----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=9cX3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210709' into staging
ppc patch queue 2021-07-09
Here's a (probably) final pull request before the qemu-6.1 soft
freeze. Includes:
* Implementation of the new H_RPT_INVALIDATE hypercall
* Virtual Open Firmware for pSeries and pegasos2 machine types.
This is an experimental minimal Open Firmware implementation which
works by delegating nearly everything to qemu itself via a special
hypercall.
* A number of cleanups to the ppc soft MMU code
* Fix to handling of two-level radix mode translations for the
powernv machine type
* Update the H_GET_CPU_CHARACTERISTICS call with newly defined bits.
This will allow more flexible handling of possible future CPU
Spectre-like flaws
* Correctly treat mtmsrd as an illegal instruction on BookE cpus
* Firmware update for the ppce500 machine type
# gpg: Signature made Fri 09 Jul 2021 06:16:42 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210709: (33 commits)
target/ppc: Support for H_RPT_INVALIDATE hcall
linux-headers: Update
spapr: Fix implementation of Open Firmware client interface
target/ppc: Don't compile ppc_tlb_invalid_all without TCG
ppc/pegasos2: Implement some RTAS functions with VOF
ppc/pegasos2: Fix use of && instead of &
ppc/pegasos2: Use Virtual Open Firmware as firmware replacement
target/ppc/spapr: Update H_GET_CPU_CHARACTERISTICS L1D cache flush bits
target/ppc: Allow virtual hypervisor on CPU without HV
ppc/pegasos2: Introduce Pegasos2MachineState structure
target/ppc: mtmsrd is an illegal instruction on BookE
spapr: Implement Open Firmware client interface
docs/system: ppc: Update ppce500 documentation with eTSEC support
roms/u-boot: Bump ppce500 u-boot to v2021.07 to add eTSEC support
target/ppc: change ppc_hash32_xlate to use mmu_idx
target/ppc: introduce mmu-books.h
target/ppc: changed ppc_hash64_xlate to use mmu_idx
target/ppc: fix address translation bug for radix mmus
target/ppc: Fix compilation with DEBUG_BATS debug option
target/ppc: Fix compilation with FLUSH_ALL_TLBS debug option
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a space in the message printed when gicr_read*/gicr_write* returns
MEMTX_ERROR in arm_gicv3_redist.c.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210706211432.31902-1-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Nick Hudson <hnick@vmware.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The stellaris board doesn't emulate the handling of the OLED
chipselect line correctly. Expand the comment describing this,
including a sketch of the theoretical correct way to do it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Luminary PL061s in the Stellaris LM3S9695 don't all have the same
reset value for GPIOPUR. We can get away with not letting the board
configure the PUR reset value because we don't actually wire anything
up to the lines which should reset to pull-up. Add a comment noting
this omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PL061 comes out of reset with all its lines configured as input,
which means they might need to be pulled to 0 or 1 depending on the
'pullups' and 'pulldowns' properties. Currently we do not assert
these lines on reset; they will only be set whenever the guest first
touches a register that triggers a call to pl061_update().
Convert the device to three-phase reset so we have a place where we
can safely call qemu_set_irq() to set the floating lines to their
correct values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For the virt board we have two PL061 devices -- one for NonSecure which
is inputs only, and one for Secure which is outputs only. For the former,
we don't care whether its outputs are pulled low or high when the line is
configured as an input, because we don't connect them. For the latter,
we do care, because we wire the lines up to the gpio-pwr device, which
assumes that level 1 means "do the action" and 1 means "do nothing".
For consistency in case we add more outputs in future, configure both
PL061s to pull GPIO lines down to 0.
Reported-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL061 GPIO does not itself include pullup or pulldown resistors
to set the value of a GPIO line treated as an output when it is
configured as an input (ie when the PL061 itself is not driving it).
In real hardware it is up to the board to add suitable pullups or
pulldowns. Currently our implementation hardwires this to "outputs
pulled high", which is correct for some boards (eg the realview ones:
see figure 3-29 in the "RealView Platform Baseboard for ARM926EJ-S
User Guide" DUI0224I), but wrong for others.
In particular, the wiring in the 'virt' board and the gpio-pwr device
assumes that wires should be pulled low, because otherwise the
pull-to-high will trigger a shutdown or reset action. (The only
reason this doesn't happen immediately on startup is due to another
bug in the PL061, where we don't assert the GPIOs to the correct
value on reset, but will do so as soon as the guest touches a
register and pl061_update() gets called.)
Add properties to the pl061 so the board can configure whether it
wants GPIO lines to have pullup, pulldown, or neither.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are pull-up,
pull-down, or truly floating. Instead of assuming all lines are pulled
high, honour the PUR and PDR registers.
For the plain PL061, continue to assume that lines have an external
pull-up resistor, as we did before.
The stellaris board actually relies on this behaviour -- the CD line
of the ssd0323 display device is connected to GPIO output C7, and it
is only because of a different bug which we're about to fix that we
weren't incorrectly driving this line high on reset and putting the
ssd0323 into data mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add a comment documenting the "QEMU interface" of this device:
which MMIO regions, IRQ lines, GPIO lines, etc it exposes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the tracepoint, rather
than having lots of early-returns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the pl061_read() and pl061_write() functions handle offsets
using a combination of three if() statements and a switch(). Clean
this up to use just a switch, using case ranges.
This requires that instead of catching accesses to the luminary-only
registers on a stock PL061 via a check on s->rsvd_start we use
an "is this luminary?" check in the cases for each luminary-only
register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
icv_eoir_write() and icv_dir_write() ignore invalid virtual IRQ numbers
(like LPIs). The issue is that these functions check against the number
of implemented IRQs (QEMU's default is num_irq=288) which can be lower
than the maximum virtual IRQ number (1020 - 1). The consequence is that
if a hypervisor creates an LR for an IRQ between 288 and 1020, then the
guest is unable to deactivate the resulting IRQ. Note that other
functions that deal with large IRQ numbers, like icv_iar_read, check
against 1020 and not against num_irq.
Fix the checks by using GICV3_MAXIRQ (1020) instead of the number of
implemented IRQs.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-id: 20210702233701.3369-1-ricarkol@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
New mini-kernel test for STM32VLDISCOVERY USART1.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-5-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the target guide for Netduino 2, Netduino Plus 2 and STM32VLDISCOVERY.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-4-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch drops the 'x-' prefix from x-blockdev-reopen.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-7-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This test swaps the images used by two active block devices.
This is now possible thanks to the new ability to run
x-blockdev-reopen on multiple devices at the same time.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-6-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
[ kwolf: Fixed AioContext locking ]
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-5-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As the BlockReopenQueue can contain nodes in multiple AioContexts, only
one of which may be locked when AIO_WAIT_WHILE() can be called, we can't
let the caller lock the right contexts. Instead, individually lock the
AioContext of a single node when iterating the queue.
Reintroduce bdrv_reopen() as a wrapper for reopening a single node that
drains the node and temporarily drops the AioContext lock for
bdrv_reopen_multiple().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the code to free a BlockReopenQueue to a separate function.
It will be used in a subsequent patch.
[ kwolf: Also free explicit_options and options, and explicitly
qobject_ref() the value when it continues to be used. This makes
future memory leaks less likely. ]
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Without an external data file, s->data_file is a second pointer with the
same value as bs->file. When changing bs->file to a different BdrvChild
and freeing the old BdrvChild, s->data_file must also be updated,
otherwise it points to freed memory and causes crashes.
This problem was caught by iotests case 245.
Fixes: df2b7086f169239ebad5d150efa29c9bb6d4f820
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210708114709.206487-2-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When removeing support for qemu-img being able to create backing
chains without embedded backing formats, we caused a poor error
message as caught by iotest 114. Improve the situation to inform the
user what went wrong.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210708155228.2666172-1-eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Back in commit d9f059aa6c (qemu-img: Deprecate use of -b without -F),
we deprecated the ability to create a file with a backing image that
requires qemu to perform format probing. Qemu can still probe older
files for backwards compatibility, but it is time to finish off the
ability to create such images, due to the potential security risk they
present. Update a couple of iotests affected by the change.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210503213600.569128-3-eblake@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This was deprecated back in bc5ee6da7 (qcow2: Deprecate use of
qemu-img amend to change backing file), and no one in the meantime has
given any reasons why it should be supported. Time to make change
attempts a hard error (but for convenience, specifying the _same_
backing chain is not forbidden). Update a couple of iotests to match.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210503213600.569128-2-eblake@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
drive_backup_prepare() does bdrv_drained_begin() in hope that
bdrv_drained_end() will be called in drive_backup_clean(). Still we
need to set state->bs for this to work. That's done too late: a lot of
failure paths in drive_backup_prepare() miss setting state->bs. Fix
that.
Fixes: 2288ccfac9
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/399
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210608171852.250775-1-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
dev->max_queues was never initialised for backends that don't support
VHOST_USER_PROTOCOL_F_MQ, so it would use 0 as the maximum number of
queues to check against and consequently fail for any such backend.
Set it to 1 if the backend doesn't have multiqueue support.
Fixes: c90bd505a3
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210705171429.29286-1-kwolf@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
adding myself as a designated reviewer.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-Id: <20210707180449.32665-2-pl@kamp.de>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
task->complete is a bool not an integer.
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-Id: <20210707180449.32665-1-pl@kamp.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Test that +w on read-only FUSE exports returns an EROFS error. u+x on
the other hand should work. (There is no special reason to choose u+x
here, it simply is like +w another flag that is not set by default.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20210625142317.271673-6-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow changing the file mode, UID, and GID through SETATTR.
Without allow_other, UID and GID are not allowed to be changed, because
it would not make sense. Also, changing group or others' permissions
is not allowed either.
For read-only exports, +w cannot be set.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20210625142317.271673-5-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to support changing other attributes than the file size in
fuse_setattr(), we have to give each its own independent branch. This
also applies to the only attribute we do support right now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210625142317.271673-4-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Without the allow_other mount option, no user (not even root) but the
one who started qemu/the storage daemon can access the export. Allow
users to configure the export such that such accesses are possible.
While allow_other is probably what users want, we cannot make it an
unconditional default, because passing it is only possible (for non-root
users) if the global fuse.conf configuration file allows it. Thus, the
default is an 'auto' mode, in which we first try with allow_other, and
then fall back to without.
FuseExport.allow_other reports whether allow_other was actually used as
a mount option or not. Currently, this information is not used, but a
future patch will let this field decide whether e.g. an export's UID and
GID can be changed through chmod.
One notable thing about 'auto' mode is that libfuse may print error
messages directly to stderr, and so may fusermount (which it executes).
Our export code cannot really filter or hide them. Therefore, if 'auto'
fails its first attempt and has to fall back, fusermount will print an
error message that mounting with allow_other failed.
This behavior necessitates a change to iotest 308, namely we need to
filter out this error message (because if the first attempt at mounting
with allow_other succeeds, there will be no such message).
Furthermore, common.rc's _make_test_img should use allow-other=off for
FUSE exports, because iotests generally do not need to access images
from other users, so allow-other=on or allow-other=auto have no
advantage. OTOH, allow-other=on will not work on systems where
user_allow_other is disabled, and with allow-other=auto, we get said
error message that we would need to filter out again. Just disabling
allow-other is simplest.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20210625142317.271673-3-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We do not do any permission checks in fuse_open(), so let the kernel do
them. We already let fuse_getattr() report the proper UNIX permissions,
so this should work the way we want.
This causes a change in 308's reference output, because now opening a
non-writable export with O_RDWR fails already, instead of only actually
attempting to write to it. (That is an improvement.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20210625142317.271673-2-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
uri_free() checks if its argument is NULL in uri_clean() and g_free().
There is no need to check the argument before the call.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Message-Id: <20210629063602.4239-1-xypron.glpk@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
librbd supports 1 byte alignment for all aio operations.
Currently, there is no API call to query limits from the Ceph
ObjectStore backend. So drop the bdrv_refresh_limits completely
until there is such an API call.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Message-Id: <20210702172356.11574-7-idryomov@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
