The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are pull-up,
pull-down, or truly floating. Instead of assuming all lines are pulled
high, honour the PUR and PDR registers.
For the plain PL061, continue to assume that lines have an external
pull-up resistor, as we did before.
The stellaris board actually relies on this behaviour -- the CD line
of the ssd0323 display device is connected to GPIO output C7, and it
is only because of a different bug which we're about to fix that we
weren't incorrectly driving this line high on reset and putting the
ssd0323 into data mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add a comment documenting the "QEMU interface" of this device:
which MMIO regions, IRQ lines, GPIO lines, etc it exposes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the tracepoint, rather
than having lots of early-returns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the pl061_read() and pl061_write() functions handle offsets
using a combination of three if() statements and a switch(). Clean
this up to use just a switch, using case ranges.
This requires that instead of catching accesses to the luminary-only
registers on a stock PL061 via a check on s->rsvd_start we use
an "is this luminary?" check in the cases for each luminary-only
register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
qemu has 2 type of functions: shutdown and reboot. Shutdown
function has to be used for machine shutdown. Otherwise we cause
a reset with a bogus "cause" value, when we intended a shutdown.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210625111842.3790-3-maxim.uvarov@linaro.org
[PMM: tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Headers should be included from the 'include/' directory,
not from the root directory.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210516205034.694788-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Target unicore32 was deprecated in commit 8e4ff4a8d2, v5.2.0. See
there for rationale.
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-3-armbru@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Implement gpio-pwr driver to allow reboot and poweroff machine.
This is simple driver with just 2 gpios lines. Current use case
is to reboot and poweroff virt machine in secure mode. Secure
pl066 gpio chip is needed for that.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The max7310_gpio_set() handler is static and only used by
qdev_init_gpio_in, initialized with 8 IRQs. The 'line'
argument can not be out of the [0-8[ range.
Replace the dead code by an assertion.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200910072325.439344-2-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1594631126-36631-1-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
Instead of logging guest accesses to invalid register offsets in this
device using zaurus_printf() (which just prints to stderr), use the
usual qemu_log_mask(LOG_GUEST_ERROR,...).
Since this was the only use of the zaurus_printf() macro outside
spitz.c, we can move the definition of that macro from sharpsl.h
to spitz.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-14-peter.maydell@linaro.org
Add a definition for the number of GPIO lines controlled by a PL061
instance, and use it instead of the hardcoded magic value 8.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200519085143.1376-1-geert+renesas@glider.be
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
Fix warning reported by Clang static code analyzer:
hw/gpio/aspeed_gpio.c:717:18: warning: Value stored to 'g_idx' during its initialization is never read
int set_idx, g_idx = *group_idx;
^~~~~ ~~~~~~~~~~
Reported-by: Clang Static Analyzer
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200422133152.16770-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove a direct include of assert.h -- this is already
provided by qemu/osdep.h, and it breaks our rule that the
first include must always be osdep.h.
In particular we must get the assert() macro via osdep.h
to avoid compile failures on mingw (see the comment in
osdep.h where we redefine assert() for that platform).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200403124712.24826-1-peter.maydell@linaro.org
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Move/adapt the existing TODO comment about a clock framework.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The property names of AST2600 GPIO 1.8V model are one character bigger
than the names of the other ASPEED GPIO model. Increase the string
buffer size by one and be more strict on the expected pattern of the
property name.
This fixes the QOM test of the ast2600-evb machine under :
Apple LLVM version 10.0.0 (clang-1000.10.44.4)
Target: x86_64-apple-darwin17.7.0
Thread model: posix
InstalledDir: /Library/Developer/CommandLineTools/usr/bin
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Fixes: 36d737ee82 ("hw/gpio: Add in AST2600 specific implementation")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191023130455.1347-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 has the same sets of 3.6v gpios as the AST2400 plus an
addtional two sets of 1.8V gpios.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-15-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPIO pins are arranged in groups of 8 pins labeled A,B,..,Y,Z,AA,AB,AC.
(Note that the ast2400 controller only goes up to group AB).
A set has four groups (except set AC which only has one) and is
referred to by the groups it is composed of (eg ABCD,EFGH,...,YZAAAB).
Each set is accessed and controlled by a bank of 14 registers.
These registers operate on a per pin level where each bit in the register
corresponds to a pin, except for the command source registers. The command
source registers operate on a per group level where bits 24, 16, 8 and 0
correspond to each group in the set.
eg. registers for set ABCD:
|D7...D0|C7...C0|B7...B0|A7...A0| <- GPIOs
|31...24|23...16|15....8|7.....0| <- bit position
Note that there are a couple of groups that only have 4 pins.
There are two ways that this model deviates from the behaviour of the
actual controller:
(1) The only control source driving the GPIO pins in the model is the ARM
model (as there currently aren't models for the LPC or Coprocessor).
(2) None of the registers in the model are reset tolerant (needs
integration with the watchdog).
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-2-clg@kaod.org
[clg: fixed missing header files
made use of HWADDR_PRIx to fix compilation on windows ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Some drivers do I2C bitbanging by keeping the output to 0 and flipping
the GPIO direction between input and output (see for example in Linux
gpio_set_open_drain_value_commit, in drivers/gpio/gpiolib.c).
When the GPIO is set to input, the pull-up resistor brings the output
to 1, while when the GPIO is set to output, the output driver brings
the output to 0.
Implement this for the nRF51 GPIO device model. First, if both input and
output are floating, and there is a pull-up or pull-down resistor
configured, do not just set s->in, but also make any devices listening
on the output qemu_irq receive that value. Second, if the pin is
driven both internally (output pin) and externally you don't get a
short circuit if both sides drive the pin to the same value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190317141001.3346-1-pbonzini@redhat.com
[PMM: wrapped long line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When generating the trace-events-all file, the build system simply
concatenates all the individual trace-events files. If any one of those
files does not have a final newline, the printf format string will have
the contents of the first line of the next file appended to it, which is
usually a '#' comment.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190123120016.4538-3-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
puv3_gpio_class_init().
Cc: gxt@mprc.pku.edu.cn
Cc: peter.maydell@linaro.org
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-8-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Drop the use of old_mmio in the omap2_gpio memory ops.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505580378-9044-3-git-send-email-peter.maydell@linaro.org
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This adds the BCM2835 GPIO controller.
It currently implements:
- The 54 GPIOs as outputs (qemu_irq)
- The SD controller selection via alternate function of GPIOs 48-53
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-4-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-4-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Drop the old SysBus init function and use instance_init
* Change mpc8xxx_gpio_reset to a DeviceClass::reset function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Writing the ISR register is supposed to clear interrupt status bits,
not to set them.
This patch makes '-M sabrelite' work without devicetree changes (Linux
kernel versions 3.18 to 4.7 with imx_v6_v7_defconfig and up to v4.8 with
multi_v7_defconfig; mainline has different problems).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1477361005-18646-1-git-send-email-linux@roeck-us.net
Acked-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-8-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Merge the pl061_initfn into pl061_init
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-7-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the old SysBus init into an instance_init and
DeviceClass::realize function
* Drop the SysBus init function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-6-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Include qom/object.h and exec/memory.h instead of exec/ioport.h;
exec/ioport.h was almost everywhere required only for those two
includes, not for the content of the header itself.
Remove block/aio.h, everybody is already including it through
another path.
With this change, include/hw/hw.h is freed from qemu-common.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be used by ARM virt machine as a power button.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-2-git-send-email-zhaoshenglong@huawei.com
[PMM: Use hyphen rather than underscore in type names;
add a comment briefly describing what the device does]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pl061.c emulates two GPIO devices, ARM PL061 and TI Stellaris, which
share the same read/write functions (pl061_read and pl061_write).
However PL061 and Stellaris have different GPIO register definitions
and pl061_read()/pl061_write() doesn't check it. This patch enforces
checking on offset, preventing R/W into the reserved memory area.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455814580-17699-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch removes the float_high field of PL061State, which doesn't
seem to be used anywhere. Because this changes the device state, the
version ID is also bumped up for the reason of compatiblity.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455729552-28026-3-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current QEMU doesn't clear PL061 state after reset. This causes a
weird issue with guest reboot via GPIO. Here is the device state
with two reboot requests:
(PL061State fields) data old_in_data istate
VM boot 0 0 0
After 1st ACPI reboot request 8 8 8
After VM PL061 driver ACK 8 8 0
After VM reboot 8 8 0
------------------------------------------------------------
2nd ACPI reboot request 8
In the second reboot request above, because the old_in_data field is 8,
QEMU decides that there is a pending edge IRQ already (see
pl061_update()) in input; so it doesn't raise up IRQ again. As a result
the second reboot request is lost. The correct way is to clear PL061
device state after reset.
The default reset state is found from the documents listed below. Per
Peter's suggestion that QEMU automatically calls reset function after
device initialization, this patch removes calling pl061_reset() from
pl061_initfn().
Reference:
[1] PL061 Technical Reference Manual
[2] Stellaris LM3S8962 Microcontroller Data Sheet
[3] Stellaris LM3S5P31 Microcontroller Data Sheet
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1455729552-28026-2-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-36-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-9-git-send-email-peter.maydell@linaro.org
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
The errors are all device misconfiguration. All callers use
qdev_init_nofail(), so this patch merely converts hw_error() crashes
into &error_abort crashes. Improvement, because now it crashes closer
to where the misconfiguration bug would be, and a few more bad
examples of hw_error() use are gone.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-3-git-send-email-armbru@redhat.com>
The i.MX6 GPIO device supports 2 interrupts instead of one.
* 1 for the lower 16 GPIOs.
* 1 for the upper 16 GPIOs.
i.MX31 and i.MX25 only support 1 interrupt for the 32 GPIOs.
So we add a property to turn the behavior on when required.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1447497668-1603-1-git-send-email-jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() outputis following the same format as
the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 4f2007adcf0f579864bb4dd8a825824e0e9098b8.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The masked interrupt status register should be the state of the interrupt
after masking.
There should be a logical AND instead of a logical OR between the
interrupt status and the interrupt mask.
Signed-off-by: Victor CLEMENT <victor.clement@openwide.fr>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1433154824-6927-1-git-send-email-victor.clement@openwide.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are a number of ffs(3) callers that do roughly:
bit = ffs(val);
if (bit) {
do_something(bit - 1);
}
This pattern can be converted to ctz32() like this:
zeroes = ctz32(val);
if (zeroes != 32) {
do_something(zeroes);
}
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-6-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This commit was generated mechanically by coccinelle from the following
semantic patch:
@@
expression val;
@@
- (ffs(val) - 1)
+ ctz32(val)
The call sites have been audited to ensure the ffs(0) - 1 == -1 case
never occurs (due to input validation, asserts, etc). Therefore we
don't need to worry about the fact that ctz32(0) == 32.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-5-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On e500 systems most SoCs implement a common GPIO controller that Linux
calls the "mpc8xxx" gpio controller. This patch adds an emulation model
for this device.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the missing input interrupt logic to the pl061 GPIO device. To
keep the floating output pins to stay high, the old state variable had to be
split into two separate ones for input and output - which brings the vmstate
version to 3.
Edge level interrupts and I/O were tested under Linux 3.14. Level interrupt
handling hasn't been tested.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Message-id: 54024FD2.9080204@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4540
Within scoop_gpio_handler_update, if prev_level has a high bit set, then
we get bit > 16 and that causes a buffer overrun.
Since prev_level comes from wire indirectly, this can
happen on invalid state load.
Similarly for gpio_level and gpio_dir.
To fix, limit to 16 bit.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Pointer properties can be set only by code, not by device_add. A
device with a pointer property can work with device_add only when the
property may remain null.
This is the case for property "interrupt_vector" of device
"etraxfs,pic". Add a comment there.
Set cannot_instantiate_with_device_add_yet for the other devices with
pointer properties, with a comment explaining why.
Juha Riihimäki and Peter Maydell deserve my thanks for making "pointer
property must not remain null" blatantly obvious in the OMAP devices.
Only device "smbus-eeprom" is actually changed. The others are all
sysbus devices, which get cannot_instantiate_with_device_add_yet set
in their abstract base's class init function. Setting it again in
their class init function is technically redundant, but serves as
insurance for when sysbus devices become available with device_add,
and as documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for ETRAX)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Let pl061_luminary inherit from pl061, with differing instance_init.
Introduce type constant and use QOM casts.
Signed-off-by: Andreas Färber <afaerber@suse.de>
