There is no known available OS for ppc around anymore that uses page
sizes below 4k, so it does not make much sense that we keep wasting
our time on building and testing the ppcemb-softmmu target. It has
been deprecated since two releases, and nobody complained, so let's
remove this now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we ever changed that, just make the things that are different
explicit.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement the IoTKit system control element's system information
block; this is just a pair of read-only version/config registers,
plus the usual PID/CID ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-10-peter.maydell@linaro.org
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
The Arm Cortex-M System Design Kit includes a simple watchdog module
based on a 32-bit down-counter. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Emulate the i2c part of SM501 which is used to access the EDID info
from a monitor.
The vmstate structure is changed and its version is increased but
SM501 is only used on SH and PPC sam460ex machines that don't support
cross-version migration.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Drivers for this card exists on PPC-based AmigaOS guests so it is useful to
allow users to emulate the graphics card for PPC machines.
As cirrus vga is currently preferred over std(vga) in absence of any user
choice, this change also sets the default display of spapr machines to
std as otherwise qemu refuses to start these machines. Not specifying an
explicit graphics mode is for instance done by 'make check'.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Basic emulation of the M41T80 serial (I2C) RTC chip. Only getting time
of day is implemented. Setting time and RTC alarm are not supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present the Sam460ex board is activated by the general CONFIG_PPC4XX
option. However that includes the board for both ppc-softmmu and
(deprecated) ppcemb-softmmu builds. As Sam460ex is developed, that would
require adding more things into ppcemb-softmmu, which we don't want to do.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1T5q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180622' into staging
target-arm queue:
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
# gpg: Signature made Fri 22 Jun 2018 13:56:00 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180622: (28 commits)
xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
vl.c: Don't zero-initialize statics for serial_hds
target/arm: Strict alignment for ARMv6-M and ARMv8-M Baseline
target/arm: Introduce ARM_FEATURE_M_MAIN
hw/arm/mps2-tz.c: Instantiate MPCs
hw/arm/iotkit: Wire up MPC interrupt lines
hw/arm/iotkit: Instantiate MPC
hw/misc/iotkit-secctl.c: Implement SECMPCINTSTATUS
hw/misc/tz_mpc.c: Honour the BLK_LUT settings in translate
hw/misc/tz-mpc.c: Implement correct blocked-access behaviour
hw/misc/tz-mpc.c: Implement registers
hw/misc/tz-mpc.c: Implement the Arm TrustZone Memory Protection Controller
xlnx-zynqmp: Swap Cortex-R5 for Cortex-R5F
target-arm: Add the Cortex-R5F
hw/arm/virt: Increase max_cpus to 512
hw/arm/virt: Use 256MB ECAM region by default
hw/arm/virt: Add virt-3.0 machine type
hw/arm/virt: Add a new 256MB ECAM region
hw/arm/virt: Register two redistributor regions when necessary
hw/arm/virt-acpi-build: Advertise one or two GICR structures
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- small cleanup for xtensa registers dumping (-d cpu);
- add support for debugging linux-user process with xtensa-linux-gdb
(as opposed to xtensa-elf-gdb), which can only access unprivileged
registers;
- enable MTTCG for target/xtensa;
- cleanup in linux-user/mmap area making sure that it works correctly
with limited 30-bit-wide user address space;
- import xtensa-specific definitions from the linux kernel,
conditionalize user-only/softmmu-only code and add handlers for
signals, exceptions, process/thread creation and core registers dumping.
-----BEGIN PGP SIGNATURE-----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=UCny
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xtensa/tags/20180316-xtensa' into staging
target/xtensa linux-user support.
- small cleanup for xtensa registers dumping (-d cpu);
- add support for debugging linux-user process with xtensa-linux-gdb
(as opposed to xtensa-elf-gdb), which can only access unprivileged
registers;
- enable MTTCG for target/xtensa;
- cleanup in linux-user/mmap area making sure that it works correctly
with limited 30-bit-wide user address space;
- import xtensa-specific definitions from the linux kernel,
conditionalize user-only/softmmu-only code and add handlers for
signals, exceptions, process/thread creation and core registers dumping.
# gpg: Signature made Fri 16 Mar 2018 16:46:19 GMT
# gpg: using RSA key 51F9CC91F83FA044
# gpg: Good signature from "Max Filippov <filippov@cadence.com>"
# gpg: aka "Max Filippov <max.filippov@cogentembedded.com>"
# gpg: aka "Max Filippov <jcmvbkbc@gmail.com>"
# Primary key fingerprint: 2B67 854B 98E5 327D CDEB 17D8 51F9 CC91 F83F A044
* remotes/xtensa/tags/20180316-xtensa:
MAINTAINERS: fix W: address for xtensa
qemu-binfmt-conf.sh: add qemu-xtensa
target/xtensa: add linux-user support
linux-user: drop unused target_msync function
linux-user: fix target_mprotect/target_munmap error return values
linux-user: fix assertion in shmdt
linux-user: fix mmap/munmap/mprotect/mremap/shmat
target/xtensa: support MTTCG
target/xtensa: use correct number of registers in gdbstub
target/xtensa: mark register windows in the dump
target/xtensa: dump correct physical registers
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# linux-user/syscall.c
Import list of syscalls from the kernel source. Conditionalize code/data
that is only used with softmmu. Implement exception handlers. Implement
signal hander (only the core registers for now, no coprocessors or TIE).
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
Add a new memory encryption object 'sev-guest'. The object will be used
to create encrypted VMs on AMD EPYC CPU. The object provides the properties
to pass guest owner's public Diffie-hellman key, guest policy and session
information required to create the memory encryption context within the
SEV firmware.
e.g to launch SEV guest
# $QEMU \
-object sev-guest,id=sev0 \
-machine ....,memory-encryption=sev0
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-25-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-24-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow distributions to disable the Intel and/or AMD IOMMU devices.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A lot of ARM object files are linked into the executable unconditionally,
even though we have corresponding CONFIG switches like CONFIG_PXA2XX or
CONFIG_OMAP. We should make sure to use these switches in the Makefile so
that the users can disable certain unwanted boards and devices more easily.
While we're at it, also add some new switches for the boards that do not
have a CONFIG option yet.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1520266949-29817-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code needed to get a functional PCI subsytem when using in
conjunction with upstream Linux guest (4.13+). Tested to work against
"e1000e" (network adapter, using MSI interrupts) as well as
"usb-ehci" (USB controller, using legacy PCI interrupts).
Based on "i.MX6 Applications Processor Reference Manual" (Document
Number: IMX6DQRM Rev. 4) as well as corresponding dirver in Linux
kernel (circa 4.13 - 4.16 found in drivers/pci/dwc/*)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds RISC-V into the build system enabling the following targets:
- riscv32-softmmu
- riscv64-softmmu
- riscv32-linux-user
- riscv64-linux-user
This adds defaults configs for RISC-V, enables the build for the RISC-V
CPU core, hardware, and Linux User Emulation. The 'qemu-binfmt-conf.sh'
script is updated to add the RISC-V ELF magic.
Expected checkpatch errors for consistency reasons:
ERROR: line over 90 characters
FILE: scripts/qemu-binfmt-conf.sh
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
Add emulation of aCube Sam460ex board based on AMCC 460EX embedded SoC.
This is not a complete implementation yet with a lot of components
still missing but enough for the U-Boot firmware to start and to boot
a Linux kernel or AROS.
Signed-off-by: François Revol <revol@free.fr>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Arm IoT Kit includes a "security controller" which is largely a
collection of registers for controlling the PPCs and other bits of
glue in the system. This commit provides the initial skeleton of the
device, implementing just the ID registers, and a couple of read-only
read-as-zero registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-16-peter.maydell@linaro.org
Add a model of the TrustZone peripheral protection controller (PPC),
which is used to gate transactions to non-TZ-aware peripherals so
that secure software can configure them to not be accessible to
non-secure software.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-15-peter.maydell@linaro.org
The MPS2 AN505 FPGA image includes a "FPGA control block"
which is a small set of registers handling LEDs, buttons
and some counters.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-14-peter.maydell@linaro.org
This adds the SiI9022 (and implicitly EDID I2C) device to the ARM
Versatile Express machine, and selects the two I2C devices necessary
in the arm-softmmu.mak configuration so everything will build
smoothly.
I am implementing proper handling of the graphics in the Linux
kernel and adding proper emulation of SiI9022 and EDID makes the
driver probe as nicely as before, retrieving the resolutions
supported by the "QEMU monitor" and overall just working nice.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-6-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The core SJA1000 support is independent of following
patches which map SJA1000 chip to PCI boards.
The work is based on Jin Yang GSoC 2013 work funded
by Google and mentored in frame of RTEMS project GSoC
slot donated to QEMU.
Rewritten for QEMU-2.0+ versions and architecture cleanup
by Pavel Pisa (Czech Technical University in Prague).
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CanBusState state structure is created for each
emulated CAN channel. Individual clients/emulated
CAN interfaces or host interface connection registers
to the bus by CanBusClientState structure.
The CAN core is prepared to support connection to the
real host CAN bus network. The commit with such support
for Linux SocketCAN follows.
Implementation is as simple as possible. There is no state to be
migrated, and messages prioritization and queuing are not considered
for now. But it is intended to be extended when need arises.
Development repository and more documentation at
https://gitlab.fel.cvut.cz/canbus/qemu-canbus
The work is based on Jin Yang GSoC 2013 work funded
by Google and mentored in frame of RTEMS project GSoC
slot donated to QEMU.
Rewritten for QEMU-2.0+ versions and architecture cleanup
by Pavel Pisa (Czech Technical University in Prague).
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MOS6522 VIA forms the bridge part of several Mac devices, including the
Mac via-cuda and via-pmu devices. Introduce a standard mos6522 device that
can be shared amongst multiple implementations.
This is effectively taking the 6522 parts out of cuda.c and turning them
into a separate device whilst also applying some style tidy-ups and including
a conversion to trace-events.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The i2c core and the at24c EEPROM should only be compiled and linked
on the machines that support i2c. Otherwise it's quite strange to see
the at24c-eeprom to be "available" on qemu-system-s390x for example.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1516634853-15883-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that we have the prerequisites in target/hppa/,
implement the hardware for a PA7100LC.
This also enables build for hppa-softmmu.
Signed-off-by: Helge Deller <deller@gmx.de>
[rth: Since it is all new code, squashed all branch development
withing hw/hppa/ to a single patch.]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.
The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.
The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)
Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Add the PMU IO Module Interrupt controller device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In preperation for having an ARM and MicroBlaze ZynqMP machine let's
split out the current ARM specific config options.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
This is the final stage in correcting the naming convention with respect to
sabre, APB and PBM. It is effectively a file rename from apb.c to sabre.c
along with touching up a few constants to remove the remaining references
to APB.
Note that as part of the rename process the configuration variable
CONFIG_PCI_APB is changed to CONFIG_PCI_SABRE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Move the QOM type and macros into a new include/hw/pci-bridge/simba.h
file, and add a new CONFIG_SIMBA Makefile.objs variable which is enabled
for sparc64-softmmu builds only.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Order the CONFIG switches in ppc-softmmu.mak according to the machine
classes where they are used (embedded, Mac or PReP), so that it is
easier for the users to disable a set of switches completely if they
are not needed.
Also add the missing CONFIG_IDE_SII3112 switch to the embedded section
which was previously only added to ppcemb-softmmu.mak.
And while we're at it, also remove the CONFIG_IDE_CMD646 switch since
this controller does not seem to be used by any ppc machine in QEMU.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
qemu-softmmu-ppc64 is supposed to be a superset of qemu-softmmu-ppc.
However, instead of simply including the 32-bit config file, we've
duplicated all CONFIG_xxx settings there instead. This way, we've missed
some CONFIG switches in ppc64-softmmu.mak which were only added to the
32-bit config file (e.g. CONFIG_SUNGEM). Let's fix this problem by
including the 32-bit config file into the 64-bit config file instead
of duplicating all the CONFIG switches there.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This commit introduces a new vhost-user device for block, it uses a
chardev to connect with the backend, same with Qemu virito-blk device,
Guest OS still uses the virtio-blk frontend driver.
To use it, start QEMU with command line like this:
qemu-system-x86_64 \
-chardev socket,id=char0,path=/path/vhost.socket \
-device vhost-user-blk-pci,chardev=char0,num-queues=2, \
bootindex=2... \
Users can use different parameters for `num-queues` and `bootindex`.
Different with exist Qemu virtio-blk host device, it makes more easy
for users to implement their own I/O processing logic, such as all
user space I/O stack against hardware block device. It uses the new
vhost messages(VHOST_USER_GET_CONFIG) to get block virtio config
information from backend process.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add target aarch64_be-linux-user. This allows a qemu-aarch64_be binary
to be built that will run big-endian aarch64 binaries.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-id: 20171220212308.12614-5-michael.weiser@gmx.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a common generic PCI SATA controller that is also used in PCs
but more importantly guests running on the Sam460ex board prefer this
card and have a driver for it (unlike for other SATA controllers
already emulated).
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for the Zynq Ultrascale MPSoc Generic QSPI.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-13-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vmcoreinfo is built for all targets. However, it requires fw_cfg with
DMA operations support (write operation). Restrict vmcoreinfo exposure
to architectures that are supporting FW_CFG_DMA, that is arm-virt and
x86 only atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add OpenRISC Multicore PIC which handles inter processor interrupts
(IPI) between cores. In OpenRISC all device interrupts are routed to
each core enabling this device to be simple.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
It is used by all PPC targets; we can give the directory its own
Makefile.objs file, and include it directly from target/ppc.
target/s390 can do the same when it starts using it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The device can not be instantiated on many non-x86 and just prints
some error messages, e.g.:
$ qemu-system-ppc64 -device vmxnet3 -M g3beige
[vmxnet3][WR][vmxnet3_init_msix]: Failed to initialize MSI-X, error -95
[vmxnet3][WR][vmxnet3_pci_realize]: Failed to initialize MSI-X, configuration is inconsistent.
Since vmxnet3 is a para-virtualized device that is only useful on x86,
it should also only be enabled on the x86 targets.
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Smartfusion2 SoC has hardened Microcontroller subsystem
and flash based FPGA fabric. This patch adds support for
Microcontroller subsystem in the SoC.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-5-f4bug@amsat.org
[PMD: drop cpu_model to directly use cpu type, check m3clk non null]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable it by default for the sparc64-softmmu configuration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Using $(and ...) is dangerous here: It only works as long as the first
argument is set to 'y' or completely unset. It does not work if the
first argument is set to 'n' for example. Let's use the "land" make
function instead which has been written explicitely for this purpose.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1505759538-15365-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds a simplistic emulation of the Sun GEM ethernet controller
found in Apple ASICs.
Currently we only support the Apple UniNorth 1.x variant, but the
other Apple or Sun variants should mostly be a matter of adding
PCI IDs options.
We have a very primitive emulation of a single Broadcom 5201 PHY
which is supported by the MacOS driver.
This model brings out-of-the-box networking to MacOS 9, and all
versions of OS X I tried with the mac99 platform.
Further improvements from Mark:
- Remove sungem.h file, moving constants into sungem.c as required
- Switch to using tracepoints for debugging
- Split register blocks into separate memory regions
- Use arrays in SunGEMState to hold register values
- Add state-saving support
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
VIRTIO_PCI should properly depend on CONFIG_PCI.
With this change, we can switch off pci for s390x by removing
'CONFIG_PCI=y' from the default config.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Learn to compile out vhost-user (net, scsi & upcoming users). Keep it
enabled by default on non-win32, that is assumed to be POSIX. Fail if
trying to enable it on win32.
When trying to make a vhost-user netdev, it gives the following error:
-netdev vhost-user,id=foo,chardev=chr-test: Parameter 'type' expects a netdev backend type
And similar error with the HMP/QMP monitors.
While at it, rename CONFIG_VHOST_NET_TEST CONFIG_VHOST_USER_NET_TEST
since it's a vhost-user specific variable.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rather than relying on everywhere that cares about whether the host
supports ivshmem using CONFIG_EVENTFD, make configure set an explicit
CONFIG_IVSHMEM.
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500021225-4118-3-git-send-email-peter.maydell@linaro.org
[PMM: split out from another patch, add commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current CONFIG_IVSHMEM is confusing, because it looks like it's a
flag for "do we have ivshmem support?", but actually it's a flag for
"is the ivshmem PCI device being compiled?" (and implicitly "do we
have ivshmem support?" is tested with CONFIG_EVENTFD).
Rename it to CONFIG_IVSHMEM_DEVICE to clear this confusion up;
shortly we will add a new CONFIG_IVSHMEM which really does indicate
whether the host can support ivshmem.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1500021225-4118-2-git-send-email-peter.maydell@linaro.org
Implement a model of the Serial Communication Controller (SCC) found
in MPS2 FPGA images.
The primary purpose of this device is to communicate with the
Motherboard Configuration Controller (MCC) which is located on
the MPS board itself, outside the FPGA image. This is used
for programming the MPS clock generators. The SCC also has
some basic ID registers and an output for the board LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-7-git-send-email-peter.maydell@linaro.org
Implement a model of the simple timer device found in the CMSDK.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-5-git-send-email-peter.maydell@linaro.org
Implement a model of the simple "APB UART" provided in
the Cortex-M System Design Kit (CMSDK).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500029487-14822-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Model the ARM MPS2/MPS2+ FPGA based development board.
The MPS2 and MPS2+ dev boards are FPGA based (the 2+ has a bigger
FPGA but is otherwise the same as the 2). Since the CPU itself
and most of the devices are in the FPGA, the details of the board
as seen by the guest depend significantly on the FPGA image.
We model the following FPGA images:
"mps2_an385" -- Cortex-M3 as documented in ARM Application Note AN385
"mps2_an511" -- Cortex-M3 'DesignStart' as documented in AN511
They are fairly similar but differ in the details for some
peripherals.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500029487-14822-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
This commit introduces a vhost-user device for SCSI. This is based
on the existing vhost-scsi implementation, but done over vhost-user
instead. It also uses a chardev to connect to the backend. Unlike
vhost-scsi (today), VMs using vhost-user-scsi can be live migrated.
To use it, start Qemu with a command line equivalent to:
qemu-system-x86_64 \
-chardev socket,id=vus0,path=/tmp/vus.sock \
-device vhost-user-scsi-pci,chardev=vus0,bus=pci.0,addr=...
A separate commit presents a sample application linked with libiscsi to
provide a backend for vhost-user-scsi.
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Message-Id: <1488479153-21203-4-git-send-email-felipe@nutanix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Largely inspired by the TMP105 temperature sensor, here is a model for
the TMP42{1,2,3} temperature sensors.
Specs can be found here :
http://www.ti.com/lit/gpn/tmp421
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1496739230-32109-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
We use the IOMMU_TYPE1 of VFIO to realize the subchannels
passthrough, implement a vfio based subchannels passthrough
driver called "vfio-ccw".
Support qemu parameters in the style of:
"-device vfio-ccw,sysfsdev=$mdev_file_path,devno=xx.x.xxxx'
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Xiao Feng Ren <renxiaof@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170517004813.58227-8-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Mark 3270 as non-migratable for the experimental stage. Enable
the 3270 device so that we can use x3270 client to operate the guest.
Run qemu with the arguments:
-chardev socket,id=char3270_0,host=0.0.0.0,port=23,nowait,server,tn3270 \
-device x-terminal3270,chardev=char3270_0,devno=fe.0.000a,id=terminal3270_0 \
There are some restrictions for the first stage: We don't support SSL
connections, multiple client connections and client resizing. Only
tested with the x3270 client.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Yang Chen <bjcyang@linux.vnet.ibm.com>
Reviewed-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Here's a respind of my first pull request for qemu-2.10, consisting of
assorted patches which have accumulated while qemu-2.9 stabilized.
Highlights are:
* Rework / cleanup of the XICS interrupt controller
* Substantial improvement to the 'powernv' machine type
- Includes an MMIO XICS version
* POWER9 support improvements
- POWER9 guests with KVM
- Partial support for POWER9 guests with TCG
* IOMMU and VFIO improvements
* Assorted minor changes
There are several IPMI patches here that aren't usually in my area of
maintenance, but there isn't a regular maintainer and these patches
are for the benefit of the powernv machine type.
This pull request supersedes my 2017-04-26 pull request. This new set
fixes a bug in one of the aforementioned IPMI patches which caused
clang sanitizer failures (and may have crashed on some libc / host
versions).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZAEUCAAoJEGw4ysog2bOS8O4P/01ruoUftX9JCkvqJjReMCjX
h52ygdzkoa24ekc95wjNz9uVjzRavx1AVmd3wty3Po9oPiY7Or8CmvnMoCi2g4Vj
cl2YjneAnaDuv7ud0HObOptfjtJxiNZr1la+gC+z3rIk0CdJ/XmH8Aiw5OhwimnC
2NLL8vxkvIPgjHGJQ4r2YxX6qjhiwBL39DE1YpIKJ1aonh7tgXbrytR34owEphFp
BOQLC0Sk0+GzI9LPlHTe54nQLantFkgzdZYIIA6GX8owtX3Nul/bp3YahdgiPLC1
NOSAyf7CO5+AISWsqrojncd4pTWuCSUfqoRdhSSGrpj3DeFtdiFEtmr8W1NTj+MZ
J9MP/UGQXgI0uLgvhqA41zzy/4OapIWdMczYRwVH8Fb0pFVklhuSQIE1R6V/6L7Q
Gajs6SWczCw0zVyflHXryRdaEyx67gL1Nl0NWgUuSJBt0sdOU9Rh89oNPssJcioy
ZIKCXl5W5uh8xHiFnCnMqbk6YOw15FufiQajideL03QEMztw42ZiejpZObK+yMpA
TnxUsH2p/naQbh5wn4Z+0IUQ6KubX+XstNy/p45aKujvkGHq/L5vI2JNUujIa8EL
x5vTY/zfaSh1k2J1HLm7LvwYnZTS8Mc/TKHKWOV1iGrG+4u89SiuyQq20SqXgNmE
L2SHTJjDxdUDmBWBKCRi
=Nnid
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.10-20170426' into staging
ppc patch queue 2017-04-26
Here's a respind of my first pull request for qemu-2.10, consisting of
assorted patches which have accumulated while qemu-2.9 stabilized.
Highlights are:
* Rework / cleanup of the XICS interrupt controller
* Substantial improvement to the 'powernv' machine type
- Includes an MMIO XICS version
* POWER9 support improvements
- POWER9 guests with KVM
- Partial support for POWER9 guests with TCG
* IOMMU and VFIO improvements
* Assorted minor changes
There are several IPMI patches here that aren't usually in my area of
maintenance, but there isn't a regular maintainer and these patches
are for the benefit of the powernv machine type.
This pull request supersedes my 2017-04-26 pull request. This new set
fixes a bug in one of the aforementioned IPMI patches which caused
clang sanitizer failures (and may have crashed on some libc / host
versions).
# gpg: Signature made Wed 26 Apr 2017 07:58:10 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.10-20170426: (48 commits)
MAINTAINERS: Remove myself from e500
target/ppc: Style fixes
e500,book3s: mfspr 259: Register mapped/aliased SPRG3 user read
target/ppc: Flush TLB on write to PIDR
spapr-cpu-core: Release ICPState object during CPU unrealization
ppc/pnv: generate an OEM SEL event on shutdown
ppc/pnv: add initial IPMI sensors for the BMC simulator
ppc/pnv: populate device tree for IPMI BT devices
ppc/pnv: populate device tree for serial devices
ppc/pnv: populate device tree for RTC devices
ppc/pnv: scan ISA bus to populate device tree
ppc/pnv: enable only one LPC bus
ppc/pnv: Add support for POWER8+ LPC Controller
spapr: remove the 'nr_servers' field from the machine
target/ppc: Fix size of struct PPCElfPrstatus
ipmi: introduce an ipmi_bmc_gen_event() API
ipmi: introduce an ipmi_bmc_sdr_find() API
ipmi: provide support for FRUs
ipmi: use a file to load SDRs
ppc: add IPMI support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OfeB
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini/tags/xen-20170421-v2-tag' into staging
Xen 2017/04/21 + fix
# gpg: Signature made Tue 25 Apr 2017 19:10:37 BST
# gpg: using RSA key 0x894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# gpg: aka "Stefano Stabellini <sstabellini@kernel.org>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini/tags/xen-20170421-v2-tag: (21 commits)
move xen-mapcache.c to hw/i386/xen/
move xen-hvm.c to hw/i386/xen/
move xen-common.c to hw/xen/
add xen-9p-backend to MAINTAINERS under Xen
xen/9pfs: build and register Xen 9pfs backend
xen/9pfs: send responses back to the frontend
xen/9pfs: implement in/out_iov_from_pdu and vmarshal/vunmarshal
xen/9pfs: receive requests from the frontend
xen/9pfs: connect to the frontend
xen/9pfs: introduce Xen 9pfs backend
9p: introduce a type for the 9p header
xen: import ring.h from xen
configure: use pkg-config for obtaining xen version
xen: additionally restrict xenforeignmemory operations
xen: use libxendevice model to restrict operations
xen: use 5 digit xen versions
xen: use libxendevicemodel when available
configure: detect presence of libxendevicemodel
xen: create wrappers for all other uses of xc_hvm_XXX() functions
xen: rename xen_modified_memory() to xen_hvm_modified_memory()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
OpenPOWER systems use a BT device to communicate with the BMC.
Provide support for it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJY/zFbAAoJEO8Ells5jWIR7LgH/A6lWkODVSKihnibRH82J9oe
rTsDdLgAGAMAur++tmNorPadZyMe/2+Cu0VsiIv591ldILruN6+jJydBzFtWFYE5
JQKa2VSTDu6bHPhr/UpRnWLhGzaJogklJR6YLkonDJznb1UnnTwEZ8c8+XD4gWLo
byo/dYF1yMnpVxSak/FkmCmwxc2K7s7P+r4FWO2CgAgY28F+/qERWJMbl1iUevQP
E1PC/XXEvhMdxi+6oYmWACdbW9/KwC5KKVELsQWYU1DcpQ7rWXCtA/mtKxvX+ePw
7CUK9ldeFXHE8uWVDnh3cWUL65Q8OtZarjMbrnN7xzcQDhMysStvVNS4QckN6/I=
=PEvc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 25 Apr 2017 12:22:03 BST
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
COLO-compare: Optimize tcp compare trace event
COLO-compare: Optimize tcp compare for option field
slirp: add a fake NC-SI backend
aspeed: add a FTGMAC100 nic
net/ftgmac100: add a 'aspeed' property
net: add FTGMAC100 support
hw/net: add MII definitions
colo-compare: Fix old packet check bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is not used by default on any emulated machine yet but it is
still useful to have it compiled so it can be added from the command
line for clients that can use it (e.g. MorphOS has no driver for any
other emulated video cards but can output via SM501)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: bf305f36dcde152668cf12438ef983cd09ed2d3f.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FTGMAC100 device is an Ethernet controller with DMA function that
can be found on Aspeed SoCs (which include NCSI).
It is fully compliant with IEEE 802.3 specification for 10/100 Mbps
Ethernet and IEEE 802.3z specification for 1000 Mbps Ethernet and
includes Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) interfaces. It adopts an
AHB bus interface and integrates a link list DMA engine with direct
M-Bus accesses for transmitting and receiving packets. It has
independent TX/RX fifos, supports half and full duplex (1000 Mbps mode
only supports full duplex), flow control for full duplex and
backpressure for half duplex.
The FTGMAC100 also implements IP, TCP, UDP checksum offloads and
supports IEEE 802.1Q VLAN tag insertion and removal. It offers
high-priority transmit queue for QoS and CoS applications
This model is backed with a RealTek 8211E PHY which is the chip found
on the AST2500 EVB. It is complete enough to satisfy two different
Linux drivers and a U-Boot driver. Not supported features are :
- IEEE 802.1Q VLAN
- High Priority Transmit Queue
- Wake-On-LAN functions
The code is based on the Coldfire Fast Ethernet Controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This implements the VM Generation ID feature by passing a 128-bit
GUID to the guest via a fw_cfg blob.
Any time the GUID changes, an ACPI notify event is sent to the guest
The user interface is a simple device with one parameter:
- guid (string, must be "auto" or in UUID format
xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx)
Signed-off-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The NVIC is a core v7M device that exists for all v7M CPUs;
put it under a CONFIG_ARM_V7M rather than hiding it under
CONFIG_STELLARIS.
(We'll use CONFIG_ARM_V7M for the SysTick device too
when we split it out of the NVIC.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-9-git-send-email-peter.maydell@linaro.org
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
This reverts commit d3473e147a.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Both devices seem to be specific to the ARM platform. It's confusing
for the users if they show up on other target architectures, too
(e.g. when the user runs QEMU with "-device ?" to get a list of
supported devices). Thus let's introduce proper configuration switches
so that the devices are only compiled and included when they are
really required.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently, the code to handle the legacy ISA bus is always included in
qemu. However there are lots of platforms that don't include ISA legacy
devies, and quite a few that have never used ISA legacy devices at all.
This patch allows the ISA bus code to be disabled in the configuration for
platforms where it doesn't make sense.
For now, the default configs are adjusted to include ISA on all platforms
including PCI: anything with PCI can at least in principle add an i82378
PCI->ISA bridge. Also, CONFIG_IDE_CORE which is already in pci.mak
requires ISA support.
We also explicitly enable ISA on some other non-PCI platforms which include
ISA devices: moxie, sparc and unicore32. We may want to pare this down in
future.
The platforms that will lose ISA by default are: cris, lm32, microblazeel,
microblaze, openrisc, s390x, tricore, xtensaeb, xtensa. As far as I can
tell none of these ever used ISA.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
At present, the core device model code for 8250-like serial ports
(serial.c) and the code for serial ports attached to ISA-style legacy IO
(serial-isa.c) are both controlled by the CONFIG_SERIAL variable.
There are lots and lots of embedded platforms that have 8250-like serial
ports but have never had anything resembling ISA legacy IO. Therefore,
split serial-isa into its own CONFIG_SERIAL_ISA option so it can be
disabled for platforms where it's not appropriate.
For now, I enabled CONFIG_SERIAL_ISA in every default-config where
CONFIG_SERIAL is enabled, excepting microblaze, or32, and xtensa. As best
as I can tell, those platforms never used legacy ISA, and also don't
include PCI support (which would allow connection of a PCI->ISA bridge
and/or a southbridge including legacy ISA serial ports).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'base' PCI Express Root Port includes
the common code to be re-used for all
Root Ports implementations. Most of the code
was taken from the current implementation
of Intel's IOH 3420 Root Port.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCI Expander Bridge (PXB) device is essentially a hack to allow
different PCIe devices to be assigned to different NUMA nodes on x86. Each
PXB is sort-of a separate PCI host bridge, except that its config space
is shared with the config space of the main PCI host bridge, rather than
being independent.
This is only necessary if the platform doesn't (easily) allow truly
independent PCI host bridges. AFAIK that's just x86.
This patch makes it possible to configure PXB out of the build, and adjusts
the default configs so it's only included on x86 targets.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
