Add FMT_* constants for the floating-point format field in opcodes and
tweak a few places to use them. Add enums for various invocations of
FOP and tweak gen_farith and its lone caller accordingly.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In the previous patch which introduced fprintf_function to
allow parameter checking by gcc some compiler warnings
remained unfixed.
These warnings are fixed here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When we signal a CpU exception for coprocessor 0, we should indicate
that it's for coprocessor 0 instead of coprocessor 1.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Running programs with the MIPS user-mode emulator fails during dynamic
loading, as floating-point instructions are not enabled in in
env->hflags. Move the code for doing so from fpu_init to cpu_reset so
the MIPS_HFLAG_{FPU,F64} setting doesn't get clobbered by cpu_reset
setting env->hflags to MIPS_HFLAG_UM.
The same end can be achieved by swapping the ordering of fpu_init and
cpu_reset in cpu_mips_init, but it seemed better to consolidate the
CONFIG_USER_ONLY code into a single location.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There's no good way to add this incrementally, so we do it all at once.
The only changes to shared code are in handle_delay_slot. We need to
flip ISAMode when doing a jump-and-exchange. We also need to set
ISAMode the low bit of the target address for jump-to-register.
Also, since we're now adding bits that can be in MIPS_HFLAG_BMASK_EXT,
make sure we use MIPS_HFLAG_BMASK_BASE in the places where we just want
basic information about a branch.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move delay slot handling to common code whose invocation can be
controlled from gen_intermediate_code_internal.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a common pattern in existing code. We'll also use it to
implement the mips16 SAVE/RESTORE instructions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's easier to implement mips16 shift instructions if we're not
examining the opcode inside gen_shift_{imm,}. So move ROTR and ROTRV
and do the special-case handling of SRL and SRLV inside decode_opc.
Likewise for their 64-bit counterparts.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Currently the ll/sc instructions use the virtual address in both
user and system mode. Use the physical address insteead in system
mode.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Depending on the CPU, CP0_LLAddr is either read-only or read-write,
and the returned value can be shifted by a variable amount of bits.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
The variable CP0_LLAddr represent the full lladdr, not the actual
register value, which is only part of this value and depends on the
CPU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Remove cpu_mips_register()
- move mmu_init(), fpu_init() and mvp_init() into cpu_mips_init()
- move the other parts in cpu_mips_init()
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Now that MAX_OP_PER_INSTR has been increased to a safer value, removed
the target-mips specific workaround.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Single-stepping branches on MIPS didn't work right, because the
generation of EXCP_DEBUG happened after the generation of the code to
exit the current TB. That is, given the code:
bne v0,v1,target
nop
...
target:
addu v0,v0,v1
1:
when you single-stepped through the NOP, execution wouldn't actually
halt until you reached the label `1'.
This patch corrects that and also changes single-stepping so that a
branch and its delay slot are executed as one instruction for the
purposes of single-stepping. This behavior is comparable to what other
MIPS tools (e.g. MIPSsim with MDI) do. GDB avoids placing breakpoints
in branch delay slots, so this change doesn't break anything on the GDB
side.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Problem: Our file sys-queue.h is a copy of the BSD file, but there are
some additions and it's not entirely compatible. Because of that, there have
been conflicts with system headers on BSD systems. Some hacks have been
introduced in the commits 15cc923584,
f40d753718,
96555a96d7 and
3990d09adf but the fixes were fragile.
Solution: Avoid the conflict entirely by renaming the functions and the
file. Revert the previous hacks.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Conditional moves off fp condition codes were using the result of
get_fp_bit to isolate and test the relevant condition code. However,
get_fp_bit returns the bit number of the condition code, not a
bitmask. (Compare the use of get_fp_bit in gen_compute_branch1, for
instance.)
Fixed by shifting a bitmask into place using the result of get_fp_bit in
the relevant functions (gen_mov{ci,cf_s,cf_d,cf_ps}).
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix botched merge of op_ldst_sc calls to match actual implementation.
Thanks to Aurelien Jarno for diagnosing this.
Signed-off-by: Paul Brook <paul@codesourcery.com>
MADD was not correctly writing to HI.
MSUB/MSUBU are specified as `HI||LO - product', not `product - HI||LO'.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This reverts commit r7127, r7132 is a better fix for that.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7133 c046a42c-6fe2-441c-8c8c-71466251a162
There is no need to exit the tb after a call to helper_raise_exception
as it already calls cpu_loop_exit().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7132 c046a42c-6fe2-441c-8c8c-71466251a162
check_*() functions may in fine call generate_exception(), which ends
by a call to tcg_gen_exit_tb(). As a consequence, we have to make sure
that no TCG temp variables are crossing a check_*() function.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7127 c046a42c-6fe2-441c-8c8c-71466251a162
Use a consistent naming of arguments and TCG variables across the whole
file, the same as in tcg/tcg-op.h:
- arg1, arg2, ... for arguments
- t0, t1, t2, ... for variables
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7106 c046a42c-6fe2-441c-8c8c-71466251a162
CPU state should also be saved for helpers that in fine call
cpu_unlink_tb(). Reported by Stefan Weil.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7096 c046a42c-6fe2-441c-8c8c-71466251a162
This replaces a compile time option for some targets and adds
this feature to targets which did not have a compile time option.
Add monitor command to enable or disable single step mode.
Modify monitor command "info status" to display single step mode.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@7004 c046a42c-6fe2-441c-8c8c-71466251a162
TCG does not allow the same memory location to be aliased in two
different global registers, fpu_fpr32 and fpu_fpr64.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6915 c046a42c-6fe2-441c-8c8c-71466251a162
Original idea&code by Kevin Wolf, split-up in two patches and added more
archs.
This patch introduces a flag to log CPU resets. Useful for tracing
unexpected resets (such as those triggered by x86 triple faults).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6452 c046a42c-6fe2-441c-8c8c-71466251a162
These are references to 'loglevel' that aren't on a simple 'if (loglevel &
X) qemu_log()' statement.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6340 c046a42c-6fe2-441c-8c8c-71466251a162
This is a large patch that changes all occurrences of logfile/loglevel
global variables to use the new qemu_log*() macros.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6338 c046a42c-6fe2-441c-8c8c-71466251a162
Use macros to avoid #ifdefs on debugging code.
This patch doesn't try to merge logging macros from different files,
but just unify the debugging code #ifdefs onto a macro on each file. A
further cleanup can unify the debugging macros on a common header, later
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6332 c046a42c-6fe2-441c-8c8c-71466251a162
Optimize gpr accesses when it is known at translation time that gpr != 0.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6307 c046a42c-6fe2-441c-8c8c-71466251a162
Replace runtime checks on env->user_mode_only by compile time
checks on CONFIG_USER_ONLY.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6276 c046a42c-6fe2-441c-8c8c-71466251a162
The attached patch updates the FSF address in the GPL/LGPL boilerplate
in most GPL/LGPLed files, and also in COPYING.LIB.
Signed-off-by: Stuart Brady <stuart.brady@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6162 c046a42c-6fe2-441c-8c8c-71466251a162
This switches cpu_break/watchpoint_* to TAILQ wrappers, simplifying the
code and also fixing a use after release issue in
cpu_break/watchpoint_remove_all.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5799 c046a42c-6fe2-441c-8c8c-71466251a162
This patch prepares the QEMU cpu_watchpoint/breakpoint API to allow the
succeeding enhancements this series comes with.
First of all, it overcomes MAX_BREAKPOINTS/MAX_WATCHPOINTS by switching
to dynamically allocated data structures that are kept in linked lists.
This also allows to return a stable reference to the related objects,
required for later introduced x86 debug register support.
Breakpoints and watchpoints are stored with their full information set
and an additional flag field that makes them easily extensible for use
beyond pure guest debugging.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5738 c046a42c-6fe2-441c-8c8c-71466251a162
Set t0 to 0 for unimplemented mfc0/dmfc0 instructions. This fixes a tcg
internal error while booting mips linux.
Noticed by Julia Longtin.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@5723 c046a42c-6fe2-441c-8c8c-71466251a162
