This adds a reset opcode for sifive_test device to trigger a system
reset for testing purpose.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present when "-bios image" is supplied, we just use the straight
path without searching for the configured data directories. Like
"-bios default", we add the same logic so that "-L" actually works.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a helper routine for finding firmware. It is currently
used only for "-bios default" case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The correct property name is clock-names, not clocks-names.
Without this patch, the Ethernet driver fails to instantiate with
the following error.
macb 100900fc.ethernet: failed to get macb_clk (-2)
macb: probe of 100900fc.ethernet failed with error -2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The riscv uart needs valid clocks. This requires a refereence
to the clock node. Since the SOC clock is not emulated by qemu,
add a reference to a fixed clock instead. The clock-frequency
entry in the uart node does not seem to be necessary, so drop it.
In addition to a reference to the clock, the driver also needs
an aliases entry for the serial node. Add it as well.
Without this patch, the serial driver fails to instantiate with
the following error message.
sifive-serial 10013000.uart: unable to find controller clock
sifive-serial: probe of 10013000.uart failed with error -2
when trying to boot Linux.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add support for loading initrd with "-initrd <filename>"
to the sifive_u machine. This lets us boot into Linux without
disk drive.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Extract all the functions that are not PC-machine specific into
the (arch-specific) fw_cfg.c file. This will allow other X86-machine
to reuse these functions.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-16-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the pc_build_feature_control_file() function has been
refactored to not depend of PC specific types, rename it to a
more generic name.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-15-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let the pc_build_feature_control_file() function take a generic MachineState
argument.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-14-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the FWCfgState object by argument, this will
allow us to remove the PCMachineState argument later.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-13-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the pc_build_smbios() function has been refactored to not
depend of PC specific types, rename it to a more generic name.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-12-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let the pc_build_smbios() function take a generic MachineState
argument.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-11-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the FWCfgState object by argument, this will
allow us to remove the PCMachineState argument later.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-10-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the previous commit we removed the last access to PCMachineState.
Replace it with a generic MachineState argument and use it to retrieve
the CPUArchIdList.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the CPUArchIdList array by argument, this will
allow us to remove the PCMachineState argument later.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-8-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the apic_id_limit value by argument, this will
allow us to remove the PCMachineState argument later.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-7-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The boot_cpus is used once. Pass it by argument, this will
allow us to remove the PCMachineState argument later.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-6-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The bochs_bios_init() function is not restricted to the Bochs
BIOS and is useful to other BIOS.
Since it is not specific to the PC machine, and can be reused
by other machines of the X86 architecture, rename it as
fw_cfg_arch_create().
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-5-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The address_space_memory variable is used once.
Use it in place and remove the argument.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-3-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To be able to extract the e820* code out of this file (in the next
patch), access e820_entries with its correct helper.
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190818225414.22590-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes a possible integer overflow when we calculate
the total size of ELF segments loaded.
Reported-by: Coverity (CID 1405299)
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190910124828.39794-1-sgarzare@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CONFIG_ACPI_PCI is a hard requirement of acpi-build.c, which is built
unconditionally for x86 target. Putting it in default-configs/ suggests
that it can be easily disabled, which isn't true.
Relocate the symbol with the other acpi-build.c requirements, under
'config PC'. This is similar to what is done for the arm 'virt' machine
type and CONFIG_ACPI_PCI
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Message-Id: <e73e6edff68fd30d69c6a1d02c9ef9192f773c63.1568049871.git.crobinso@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The APB frequency can be calculated directly when needed from the
HPLL_PARAM and CLK_SEL register values. This removes useless state in
the model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-11-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
and use a class AspeedSCUClass to define each SoC characteristics.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-10-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the missing checksum calculation on normal DMA transfer.
According to the datasheet this is how the SMC should behave.
Verified on AST1250 that the hardware matches the behaviour.
Signed-off-by: Christian Svensson <bluecmd@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Emulate read errors in the DMA Checksum Register for high frequencies
and optimistic settings of the Read Timing Compensation Register. This
will help in tuning the SPI timing calibration algorithm. Errors are
only injected when the property "inject_failure" is set to true as
suggested by Philippe.
The values below are those to expect from the first flash device of
the FMC controller of a palmetto-bmc machine.
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing calibration, the SPI clock rate in the CE0 Control Register
and the read delay cycles in the Read Timing Compensation Register are
set using bit[11:4] of the DMA Control Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190904070506.1052-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The FMC controller on the Aspeed SoCs support DMA to access the flash
modules. It can operate in a normal mode, to copy to or from the flash
module mapping window, or in a checksum calculation mode, to evaluate
the best clock settings for reads.
The model introduces two custom address spaces for DMAs: one for the
AHB window of the FMC flash devices and one for the DRAM. The latter
is populated using a "dram" link set from the machine with the RAM
container region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190904070506.1052-6-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are no QEMU Aspeed machines using the SoCs "ast2400-a0" or
"ast2400".
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-4-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GPIO pins are arranged in groups of 8 pins labeled A,B,..,Y,Z,AA,AB,AC.
(Note that the ast2400 controller only goes up to group AB).
A set has four groups (except set AC which only has one) and is
referred to by the groups it is composed of (eg ABCD,EFGH,...,YZAAAB).
Each set is accessed and controlled by a bank of 14 registers.
These registers operate on a per pin level where each bit in the register
corresponds to a pin, except for the command source registers. The command
source registers operate on a per group level where bits 24, 16, 8 and 0
correspond to each group in the set.
eg. registers for set ABCD:
|D7...D0|C7...C0|B7...B0|A7...A0| <- GPIOs
|31...24|23...16|15....8|7.....0| <- bit position
Note that there are a couple of groups that only have 4 pins.
There are two ways that this model deviates from the behaviour of the
actual controller:
(1) The only control source driving the GPIO pins in the model is the ARM
model (as there currently aren't models for the LPC or Coprocessor).
(2) None of the registers in the model are reset tolerant (needs
integration with the watchdog).
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-2-clg@kaod.org
[clg: fixed missing header files
made use of HWADDR_PRIx to fix compilation on windows ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
New feature:
UUID validation check from Yury Kotov
plus a bunch of fixes.
-----BEGIN PGP SIGNATURE-----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=W+5Q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20190912a' into staging
Migration pull 2019-09-12
New feature:
UUID validation check from Yury Kotov
plus a bunch of fixes.
# gpg: Signature made Thu 12 Sep 2019 14:48:28 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20190912a:
migration: fix one typo in comment of function migration_total_bytes()
migration/qemu-file: fix potential buf waste for extra buf_index adjustment
migration/qemu-file: remove check on writev_buffer in qemu_put_compression_data
migration: Fix postcopy bw for recovery
tests/migration: Add a test for validate-uuid capability
tests/libqtest: Allow setting expected exit status
migration: Add validate-uuid capability
qemu-file: Rework old qemu_fflush comment
migration: register_savevm_live doesn't need dev
hw/net/vmxnet3: Fix leftover unregister_savevm
migration: cleanup check on ops in savevm.handlers iterations
migration: multifd_send_thread always post p->sem_sync when error happen
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the MIPS CPU implementation uses the new
do_transaction_failed hook, we can remove the old code that handled
the do_unassigned_access hook.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20190802160458.25681-4-peter.maydell@linaro.org>
The MIPS Jazz ('magnum' and 'pica61') boards have some code which
overrides the CPU's do_unassigned_access hook, so they can intercept
it and not raise exceptions on data accesses to invalid addresses,
only for instruction fetches.
We want to switch MIPS over to using the do_transaction_failed
hook instead, so add an intercept for that as well, and make
the board code install whichever hook the CPU is actually using.
Once we've changed the CPU implementation we can remove the
redundant code for the old hook.
Note: I am suspicious that the behaviour as implemented here may not
be what the hardware really does. It was added in commit
54e755588c to restore the behaviour that was broken by
commit c658b94f6e. But prior to commit c658b94f6e
every MIPS board generated exceptions for instruction access to
invalid addresses but not for data accesses; and other boards,
notably Malta, were fixed by making all invalid accesses behave as
reads-as-zero (see the call to empty_slot_init() in
mips_malta_init()). Hardware that raises exceptions for instruction
access and not data access seems to me to be an unlikely design, and
it's possible that the right way to emulate this is to make the Jazz
boards do what we did with Malta (or some variation of that).
Nonetheless, since I don't have access to real hardware to test
against I have taken the approach of "make QEMU continue to behave
the same way it did before this commit". I have updated the comment
to correct the parts that are no longer accurate and note that
the hardware might behave differently.
The test case for the need for the hook-hijacking is in
https://bugs.launchpad.net/qemu/+bug/1245924 That BIOS will boot OK
either with this overriding of both hooks, or with a simple "global
memory region to ignore bad accesses of all types", so it doesn't
provide evidence either way, unfortunately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20190802160458.25681-2-peter.maydell@linaro.org>
Commit 78dd48df3 removed the last caller of register_savevm_live for an
instantiable device (rather than a single system wide device);
so trim out the parameter.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822115433.12070-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 78dd48df3 reworked vmxnet3's live migration but left a straggling
unregister_savevm call. Remove it, although it doesn't seem to have
any bad effect.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822111218.12079-1-dgilbert@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Most of the code in hw/misc/ does not directly depend on CPU-specific
code. Mark it as "common" so that the code can be shared between e.g.
qemu-system-arm and qemu-system-aarch64, or between the various mips
flavours, instead of recompiling it for each and every target again
and again.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190902162638.28142-1-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
The NeXTcube uses a normal 8530 serial controller, so we can simply use
our normal "escc" device here.
While we're at it, also add a boot-serial-test for the next-cube machine,
now that the serial output works.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-6-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
On Sparc and PowerMac, the bit 0 of the address selects the register
type (control or data) and bit 1 selects the channel (B or A).
On m68k Macintosh and NeXTcube, the bit 0 selects the channel and
bit 1 the register type.
This patch introduces a new parameter (bit_swap) to the device interface
to indicate bits usage must be swapped between registers and channels.
For the moment all the machines use the bit 0, but this change will be
needed to emulate the Quadra 800 or NeXTcube machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
[thh: added NeXTcube to the patch description]
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-5-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
It is still quite incomplete (no SCSI, no floppy emulation, no network,
etc.), but the firmware already shows up the debug monitor prompt in the
framebuffer display, so at least the very basics are already working.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-cube.c
and altered quite a bit to fit the latest interface and coding conventions
of the current QEMU.
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-4-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
It is likely still quite incomplete (e.g. mouse and interrupts are not
implemented yet), but it is good enough for keyboard input at the firmware
monitor.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-kbd.c
and altered to fit the latest interface of the current QEMU (e.g. to use
memory_region_init_io() instead of cpu_register_physical_memory()).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-3-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
The NeXTcube uses a linear framebuffer with 4 greyscale colors and
a fixed resolution of 1120 * 832.
This code has been taken from Bryce Lanham's GSoC 2011 NeXT branch at
https://github.com/blanham/qemu-NeXT/blob/next-cube/hw/next-fb.c
and altered to fit the latest interface of the current QEMU (e.g.
the device has been "qdev"-ified etc.).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190831074519.32613-2-huth@tuxfamily.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
