The AST1030 machine initialization was not respecting the Aspeed SoC
property "uart-default", which specifies which UART should be connected to
the first serial device, it was just always connecting UART5. This doesn't
change any behavior, because the default value for "uart-default" is UART5,
but it makes it possible to override this in new machine definitions using
the AST1030.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-4-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500,
AST2600, and AST1030.
This also includes the new UART interfaces added in the AST2600 and AST1030
from UART6 to UART13. The addresses and interrupt numbers for these two
later chips are identical.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and make routine aspeed_soc_get_irq() common to all SoCs. This will be
useful to share code.
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516055620.2380197-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the 'fby35-bmc' machine type based on the kernel DTS[1] and userspace
i2c setup scripts[2]. Undefined values are inherited from the AST2600-EVB.
Reference images can be found in Facebook OpenBMC Github Release assets
as "fby35.mtd". [3]
You can boot the reference images as follows (fby35 uses dual-flash):
qemu-system-arm -machine fby35-bmc \
-drive file=fby35.mtd,format=raw,if=mtd \
-drive file=fby35.mtd,format=raw,if=mtd \
-nographic
[1] 412d505325/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
[2] e2294ff5d3/meta-facebook/meta-fby35/recipes-fby35/plat-utils/files/setup-dev.sh
[3] https://github.com/facebook/openbmc/releases
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220503225925.1798324-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We had a few CPTR_* bits defined, but missed quite a few.
Complete all of the fields up to ARMv9.2.
Use FIELD_EX64 instead of manual extract32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220517054850.177016-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The traditional ptimer behaviour includes a collection of weird edge
case behaviours. In 2016 we improved the ptimer implementation to
fix these and generally make the behaviour more flexible, with
ptimers opting in to the new behaviour by passing an appropriate set
of policy flags to ptimer_init(). For backwards-compatibility, we
defined PTIMER_POLICY_DEFAULT (which sets no flags) to give the old
weird behaviour.
This turns out to be a poor choice of name, because people writing
new devices which use ptimers are misled into thinking that the
default is probably a sensible choice of flags, when in fact it is
almost always not what you want. Rename PTIMER_POLICY_DEFAULT to
PTIMER_POLICY_LEGACY and beef up the comment to more clearly say that
new devices should not be using it.
The code-change part of this commit was produced by
sed -i -e 's/PTIMER_POLICY_DEFAULT/PTIMER_POLICY_LEGACY/g' $(git grep -l PTIMER_POLICY_DEFAULT)
with the exception of a test name string change in
tests/unit/ptimer-test.c which was added manually.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220516103058.162280-1-peter.maydell@linaro.org
The virt board generates a gpio-keys node in the dtb, but it
incorrectly gives this node #size-cells and #address-cells
properties. If you dump the dtb with 'machine dumpdtb=file.dtb'
and run it through dtc, dtc will warn about this:
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the bogus properties.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-3-peter.maydell@linaro.org
In the virt board with secure=on we put two nodes in the dtb
for flash devices: one for the secure-only flash, and one
for the non-secure flash. We get the reg properties for these
correct, but in the DT node name, which by convention includes
the base address of devices, we used the wrong address. Fix it.
Spotted by dtc, which will complain
Warning (unique_unit_address): /flash@0: duplicate unit-address (also used in node /secflash@0)
if you dump the dtb from QEMU with -machine dumpdtb=file.dtb
and then decompile it with dtc.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220513131316.4081539-2-peter.maydell@linaro.org
This adds code to instantiate the slightly extended ACPI root port
description in DSDT as per the CXL 2.0 specification.
Basically a cut and paste job from the i386/pc code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-30-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As part of converting -boot to a property with a QAPI type, define
the struct and use it throughout QEMU to access boot configuration.
machine_boot_parse takes care of doing the QemuOpts->QAPI conversion by
hand, for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When CPU-to-NUMA association isn't explicitly provided by users,
the default one is given by mc->get_default_cpu_node_id(). However,
the CPU topology isn't fully considered in the default association
and this causes CPU topology broken warnings on booting Linux guest.
For example, the following warning messages are observed when the
Linux guest is booted with the following command lines.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host \
-cpu host \
-smp 6,sockets=2,cores=3,threads=1 \
-m 1024M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=128M \
-object memory-backend-ram,id=mem1,size=128M \
-object memory-backend-ram,id=mem2,size=128M \
-object memory-backend-ram,id=mem3,size=128M \
-object memory-backend-ram,id=mem4,size=128M \
-object memory-backend-ram,id=mem4,size=384M \
-numa node,nodeid=0,memdev=mem0 \
-numa node,nodeid=1,memdev=mem1 \
-numa node,nodeid=2,memdev=mem2 \
-numa node,nodeid=3,memdev=mem3 \
-numa node,nodeid=4,memdev=mem4 \
-numa node,nodeid=5,memdev=mem5
:
alternatives: patching kernel code
BUG: arch topology borken
the CLS domain not a subset of the MC domain
<the above error log repeats>
BUG: arch topology borken
the DIE domain not a subset of the NODE domain
With current implementation of mc->get_default_cpu_node_id(),
CPU#0 to CPU#5 are associated with NODE#0 to NODE#5 separately.
That's incorrect because CPU#0/1/2 should be associated with same
NUMA node because they're seated in same socket.
This fixes the issue by considering the socket ID when the default
CPU-to-NUMA association is provided in virt_possible_cpu_arch_ids().
With this applied, no more CPU topology broken warnings are seen
from the Linux guest. The 6 CPUs are associated with NODE#0/1, but
there are no CPUs associated with NODE#2/3/4/5.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-id: 20220503140304.855514-6-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, the SMP configuration isn't considered when the CPU
topology is populated. In this case, it's impossible to provide
the default CPU-to-NUMA mapping or association based on the socket
ID of the given CPU.
This takes account of SMP configuration when the CPU topology
is populated. The die ID for the given CPU isn't assigned since
it's not supported on arm/virt machine. Besides, the used SMP
configuration in qtest/numa-test/aarch64_numa_cpu() is corrcted
to avoid testing failure
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20220503140304.855514-4-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sbsa-ref machine is continuously evolving. Some of the changes we
want to make in the near future, to align with real components (e.g.
the GIC-700), will break compatibility for existing firmware.
Introduce two new properties to the DT generated on machine generation:
- machine-version-major
To be incremented when a platform change makes the machine
incompatible with existing firmware.
- machine-version-minor
To be incremented when functionality is added to the machine
without causing incompatibility with existing firmware.
to be reset to 0 when machine-version-major is incremented.
This versioning scheme is *neither*:
- A QEMU versioned machine type; a given version of QEMU will emulate
a given version of the platform.
- A reflection of level of SBSA (now SystemReady SR) support provided.
The version will increment on guest-visible functional changes only,
akin to a revision ID register found on a physical platform.
These properties are both introduced with the value 0.
(Hence, a machine where the DT is lacking these nodes is equivalent
to version 0.0.)
Signed-off-by: Leif Lindholm <quic_llindhol@quicinc.com>
Message-id: 20220505113947.75714-1-quic_llindhol@quicinc.com
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the n1 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-25-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the a76 for virt and sbsa board use.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220506180242.216785-24-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove a possible source of error by removing REGINFO_SENTINEL
and using ARRAY_SIZE (convinently hidden inside a macro) to
find the end of the set of regs being registered or modified.
The space saved by not having the extra array element reduces
the executable's .data.rel.ro section by about 9k.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move ARMCPRegInfo and all related declarations to a new
internal header, out of the public cpu.h.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220501055028.646596-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current fmc model of AST2500 EVB and AST2600 EVB can't emulate quad
mode properly so fix them using equivalent mx25l25635e and mx66u51235f
respectively.
These default settings still can be overridden using the 'fmc-model'
command line option.
Reported-by: Graeme Gregory <quic_ggregory@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220402184427.4010304-1-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The image should be supplied with ELF binary.
$ qemu-system-arm -M ast1030-evb -kernel zephyr.elf -nographic
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-9-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Guest code (u-boot) pokes at this on boot. No functionality is required
for guest code to work correctly, but it helps to document the region
being read from.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220318092211.723938-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ARM virt machine currently uses sysbus-fdt to create device tree
entries for dynamically created MMIO devices.
The RISC-V virt machine can also benefit from this, so move the code to
the core directory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-3-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Arm SMMUv3 includes an optional feature equivalent to the CPU
FEAT_BBM, which permits an OS to switch a range of memory between
"covered by a huge page" and "covered by a sequence of normal pages"
without having to engage in the traditional 'break-before-make'
dance. (This is particularly important for the SMMU, because devices
performing I/O through an SMMU are less likely to be able to cope with
the window in the sequence where an access results in a translation
fault.) The SMMU spec explicitly notes that one of the valid ways to
be a BBM level 2 compliant implementation is:
* if there are multiple entries in the TLB for an address,
choose one of them and use it, ignoring the others
Our SMMU TLB implementation (unlike our CPU TLB) does allow multiple
TLB entries for an address, because the translation table level is
part of the SMMUIOTLBKey, and so our IOTLB hashtable can include
entries for the same address where the leaf was at different levels
(i.e. both hugepage and normal page). Our TLB lookup implementation in
smmu_iotlb_lookup() will always find the entry with the lowest level
(i.e. it prefers the hugepage over the normal page) and ignore any
others. TLB invalidation correctly removes all TLB entries matching
the specified address or address range (unless the guest specifies the
leaf level explicitly, in which case it gets what it asked for). So we
can validly advertise support for BBML level 2.
Note that we still can't yet advertise ourselves as an SMMU v3.2,
because v3.2 requires support for the S2FWB feature, which we don't
yet implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220426160422.2353158-4-peter.maydell@linaro.org
Make the translation error message prettier by adding a missing space
before the parenthesis.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220427111543.124620-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Record bit in the Context Descriptor tells the SMMU to report fault
events to the event queue. Since we don't cache the Record bit at the
moment, access faults from a cached Context Descriptor are never
reported. Store the Record bit in the cached SMMUTransCfg.
Fixes: 9bde7f0674 ("hw/arm/smmuv3: Implement translate callback")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220427111543.124620-1-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It always calls the IOMMU MR translate() callback with flag=IOMMU_NONE in
memory_region_iommu_replay(). Currently, smmuv3_translate() return an
IOMMUTLBEntry with perm set to IOMMU_NONE even if the translation success,
whereas it is expected to return the actual permission set in the table
entry.
So pass the actual perm to returned IOMMUTLBEntry in the table entry.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1650094695-121918-1-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the TCG GICv4 to the virt board. For the board,
the GICv4 is very similar to the GICv3, with the only difference
being the size of the redistributor frame. The changes here are thus:
* calculating virt_redist_capacity correctly for GICv4
* changing various places which were "if GICv3" to be "if not GICv2"
* the commandline option handling
Note that using GICv4 reduces the maximum possible number of CPUs on
the virt board from 512 to 317, because we can now only fit half as
many redistributors into the redistributor regions we have defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-42-peter.maydell@linaro.org
In several places in virt.c we calculate the number of redistributors that
fit in a region of our memory map, which is the size of the region
divided by the size of a single redistributor frame. For GICv4, the
redistributor frame is a different size from that for GICv3. Abstract
out the calculation of redistributor region capacity so that we have
one place we need to change to handle GICv4 rather than several.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-41-peter.maydell@linaro.org
Everywhere we need to check which GIC version we're using, we look at
vms->gic_version and use the VIRT_GIC_VERSION_* enum values, except
in create_gic(), which copies vms->gic_version into a local 'int'
variable and makes direct comparisons against values 2 and 3.
For consistency, change this function to check the GIC version
the same way we do elsewhere. This includes not implicitly relying
on the enumeration type values happening to match the integer
'revision' values the GIC device object wants.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-40-peter.maydell@linaro.org
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/allwinner-a10.c: In function ‘aw_a10_realize’:
../hw/arm/allwinner-a10.c:135:35: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 8 [-Werror=format-overflow=]
135 | sprintf(bus, "usb-bus.%d", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-15-marcandre.lureau@redhat.com>
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/digic.c: In function ‘digic_init’:
../hw/arm/digic.c:45:54: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
45 | snprintf(name, DIGIC_TIMER_NAME_MLEN, "timer[%d]", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-14-marcandre.lureau@redhat.com>
This patch uses the defined fields to describe PWRON STRAPs for
better readability.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20220411165842.3912945-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-3-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-2-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only time we use the int_combiner_irq[] and ext_combiner_irq[]
arrays in the Exynos4210Irq struct is during realize of the SoC -- we
initialize them with the input IRQs of the combiner devices, and then
connect those to outputs of other devices in
exynos4210_init_board_irqs(). Now that the combiner objects are
easily accessible as s->int_combiner and s->ext_combiner we can make
the connections directly from one device to the other without going
via these arrays.
Since these are the only two remaining elements of Exynos4210Irq,
we can remove that struct entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-19-peter.maydell@linaro.org
Switch the creation of the combiner devices to the new-style
"embedded in state struct" approach, so we can easily refer
to the object elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-18-peter.maydell@linaro.org
At this point, the function exynos4210_init_board_irqs() splits input
IRQ lines to connect them to the input combiner, output combiner and
external GIC. The function exynos4210_combiner_get_gpioin() splits
some of the combiner input lines further to connect them to multiple
different inputs on the combiner.
Because (unlike qemu_irq_split()) the TYPE_SPLIT_IRQ device has a
configurable number of outputs, we can do all this in one place, by
making exynos4210_init_board_irqs() add extra outputs to the splitter
device when it must be connected to more than one input on each
combiner.
We do this with a new data structure, the combinermap, which is an
array each of whose elements is a list of the interrupt IDs on the
combiner which must be tied together. As we loop through each
interrupt ID, if we find that it is the first one in one of these
lists, we configure the splitter device with eonugh extra outputs and
wire them up to the other interrupt IDs in the list.
Conveniently, for all the cases where this is necessary, the
lowest-numbered interrupt ID in each group is in the range of the
external combiner, so we only need to code for this in the first of
the two loops in exynos4210_init_board_irqs().
The old code in exynos4210_combiner_get_gpioin() which is being
deleted here had several problems which don't exist in the new code
in its handling of the multi-core timer interrupts:
(1) the case labels specified bits 4 ... 8, but bit '8' doesn't
exist; these should have been 4 ... 7
(2) it used the input irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]
multiple times as the input of several different splitters,
which isn't allowed
(3) in an apparent cut-and-paste error, the cases for all the
multi-core timer inputs used "bit + 4" even though the
bit range for the case was (intended to be) 4 ... 7, which
meant it was looking at non-existent bits 8 ... 11.
None of these exist in the new code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-17-peter.maydell@linaro.org
The combiner_grp_to_gic_id[] array includes the EXT_GIC_ID_MCT_G0
and EXT_GIC_ID_MCT_G1 multiple times. This means that we will
connect multiple IRQs up to the same external GIC input, which
is not permitted. We do the same thing in the code in
exynos4210_init_board_irqs() because the conditionals selecting
an irq_id in the first loop match multiple interrupt IDs.
Overall we do this for interrupt IDs
(1, 4), (12, 4), (35, 4), (51, 4), (53, 4) for EXT_GIC_ID_MCT_G0
and
(1, 5), (12, 5), (35, 5), (51, 5), (53, 5) for EXT_GIC_ID_MCT_G1
These correspond to the cases for the multi-core timer that we are
wiring up to multiple inputs on the combiner in
exynos4210_combiner_get_gpioin(). That code already deals with all
these interrupt IDs being the same input source, so we don't need to
connect the external GIC interrupt for any of them except the first
(1, 4) and (1, 5). Remove the array entries and conditionals which
were incorrectly causing us to wire up extra lines.
This bug didn't cause any visible effects, because we only connect
up a device to the "primary" ID values (1, 4) and (1, 5), so the
extra lines would never be set to a level.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-16-peter.maydell@linaro.org
Currently for the interrupts MCT_G0 and MCT_G1 which are
the only ones in the input range of the external combiner
and which are also wired to the external GIC, we connect
them only to the internal combiner and the external GIC.
This seems likely to be a bug, as all other interrupts
which are in the input range of both combiners are
connected to both combiners. (The fact that the code in
exynos4210_combiner_get_gpioin() is also trying to wire
up these inputs on both combiners also suggests this.)
Wire these interrupts up to both combiners, like the rest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-15-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), the loop that handles IRQ lines that
are in a range that applies to the internal combiner only creates a
splitter for those interrupts which go to both the internal combiner
and to the external GIC, but it does nothing at all for the
interrupts which don't go to the external GIC, leaving the
irq_table[] array element empty for those. (This will result in
those interrupts simply being lost, not in a QEMU crash.)
I don't have a reliable datasheet for this SoC, but since we do wire
up one interrupt line in this category (the HDMI I2C device on
interrupt 16,1), this seems like it must be a bug in the existing
QEMU code. Fill in the irq_table[] entries where we're not splitting
the IRQ to both the internal combiner and the external GIC with the
IRQ line of the internal combiner. (That is, these IRQ lines go to
just one device, not multiple.)
This bug didn't have any visible guest effects because the only
implemented device that was affected was the HDMI I2C controller,
and we never connect any I2C devices to that bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-14-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), use the TYPE_SPLIT_IRQ device
instead of qemu_irq_split().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-13-peter.maydell@linaro.org
The function exynos4210_combiner_get_gpioin() currently lives in
exynos4210_combiner.c, but it isn't really part of the combiner
device itself -- it is a function that implements the wiring up of
some interrupt sources to multiple combiner inputs. Move it to live
with the other SoC-level code in exynos4210.c, along with a few
macros previously defined in exynos4210.h which are now used only
in exynos4210.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-11-peter.maydell@linaro.org
The only time we use the ext_gic_irq[] array in the Exynos4210Irq
struct is during realize of the SoC -- we initialize it with the
input IRQs of the external GIC device, and then connect those to
outputs of other devices further on in realize (including in the
exynos4210_init_board_irqs() function). Now that the ext_gic object
is easily accessible as s->ext_gic we can make the connections
directly from one device to the other without going via this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-10-peter.maydell@linaro.org
Switch the creation of the external GIC to the new-style "embedded in
state struct" approach, so we can easily refer to the object
elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-9-peter.maydell@linaro.org
The function exynos4210_init_board_irqs() currently lives in
exynos4210_gic.c, but it isn't really part of the exynos4210.gic
device -- it is a function that implements (some of) the wiring up of
interrupts between the SoC's GIC and combiner components. This means
it fits better in exynos4210.c, which is the SoC-level code. Move it
there. Similarly, exynos4210_git_irq() is used almost only in the
SoC-level code, so move it too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-8-peter.maydell@linaro.org
The exynos4210 code currently has two very similar arrays of IRQs:
* board_irqs is a field of the Exynos4210Irq struct which is filled
in by exynos4210_init_board_irqs() with the appropriate qemu_irqs
for each IRQ the board/SoC can assert
* irq_table is a set of qemu_irqs pointed to from the
Exynos4210State struct. It's allocated in exynos4210_init_irq,
and the only behaviour these irqs have is that they pass on the
level to the equivalent board_irqs[] irq
The extra indirection through irq_table is unnecessary, so coalesce
these into a single irq_table[] array as a direct field in
Exynos4210State which exynos4210_init_board_irqs() fills in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-6-peter.maydell@linaro.org
The only time we use the int_gic_irq[] array in the Exynos4210Irq
struct is in the exynos4210_realize() function: we initialize it with
the GPIO inputs of the a9mpcore device, and then a bit later on we
connect those to the outputs of the internal combiner. Now that the
a9mpcore object is easily accessible as s->a9mpcore we can make the
connection directly from one device to the other without going via
this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-5-peter.maydell@linaro.org
The exynos4210 SoC mostly creates its child devices as if it were
board code. This includes the a9mpcore object. Switch that to a
new-style "embedded in the state struct" creation, because in the
next commit we're going to want to refer to the object again further
down in the exynos4210_realize() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-4-peter.maydell@linaro.org
The Exynos4210 SoC device currently uses a custom device
"exynos4210.irq_gate" to model the OR gate that feeds each CPU's IRQ
line. We have a standard TYPE_OR_IRQ device for this now, so use
that instead.
(This is a migration compatibility break, but that is OK for this
machine type.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-2-peter.maydell@linaro.org
Connect the CRL (Clock Reset LPD) to the Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-5-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the Cortex-R5Fs of the Versal RPU (Real-time Processing Unit)
subsystem.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-3-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create an APU CPU Cluster. This is in preparation to add the RPU.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-2-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 4 TTC timers on the ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220331222017.2914409-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's not possible to provide the guest with the Security extensions
(TrustZone) when using KVM or HVF, because the hardware
virtualization extensions don't permit running EL3 guest code.
However, we weren't checking for this combination, with the result
that QEMU would assert if you tried it:
$ qemu-system-aarch64 -enable-kvm -machine virt,secure=on -cpu host -display none
Unexpected error in object_property_find_err() at ../../qom/object.c:1304:
qemu-system-aarch64: Property 'host-arm-cpu.secure-memory' not found
Aborted
Check for this combination of options and report an error, in the
same way we already do for attempts to give a KVM or HVF guest the
Virtualization or MTE extensions. Now we will report:
qemu-system-aarch64: mach-virt: KVM does not support providing Security extensions (TrustZone) to the guest CPU
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/961
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404155301.566542-1-peter.maydell@linaro.org
Convert the TARGET_WORDS_BIGENDIAN macro, similarly to what was done
with HOST_BIG_ENDIAN. The new TARGET_BIG_ENDIAN macro is either 0 or 1,
and thus should always be defined to prevent misuse.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-8-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Connect the ZynqMP APU Control device.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-7-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the ZynqMP CRF - Clock Reset FPD device.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-5-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an unimplemented SERDES (Serializer/Deserializer) area.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220316164645.2303510-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In TCG mode, if gic-version=max we always select GICv3 even if
CONFIG_ARM_GICV3_TCG is unset. We shall rather select GICv2.
This also brings the benefit of fixing qos tests errors for tests
using gic-version=max with CONFIG_ARM_GICV3_TCG unset.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220308182452.223473-3-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix for a potential memory leak
* Aspeed SMC cleanups on the definition of the number of flash devices
* New bletchley-bmc machine, AST2600 based
-----BEGIN PGP SIGNATURE-----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=5VHm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220308' into staging
aspeed queue:
* Fix for a potential memory leak
* Aspeed SMC cleanups on the definition of the number of flash devices
* New bletchley-bmc machine, AST2600 based
# gpg: Signature made Tue 08 Mar 2022 08:19:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220308:
hw: aspeed_gpio: Cleanup stray semicolon after switch
hw/arm/aspeed: add Bletchley machine type
hw/arm/aspeed: allow missing spi_model
hw/block: m25p80: Add support for w25q01jvq
aspeed/smc: Fix error log
aspeed/smc: Let the SSI core layer define the bus name
aspeed/smc: Rename 'max_peripherals' to 'cs_num_max'
aspeed/smc: Remove 'num_cs' field
aspeed: Rework aspeed_board_init_flashes() interface
aspeed/smc: Use max number of CE instead of 'num_cs'
aspeed: Fix a potential memory leak bug in write_boot_rom()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the 'bletchley-bmc' machine type based on the kernel DTS[1] and
hardware schematics available to me. The i2c model is as complete as
the current QEMU models support, but in some cases I substituted devices
that are close enough for present functionality. Strap registers are
kept the same as the AST2600-EVB until I'm able to confirm correct
values with physical hardware.
This has been tested with an openbmc image built from [2] plus a kernel
patch[3] for the SPI flash module.
1. https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts?id=a8c729e966c4e9d033242d948b0e53c2a62d32e2
2. b9432b980d
3. 25b566b9a9
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg : increased number of FMC devices to 2 to match Linux dts ]
Message-Id: <20220305000656.1944589-2-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generally all BMCs will use the fmc_model to hold their own flash
and most will have a spi_model to hold the managed system's flash,
but not all systems do. Add a simple NULL check to allow a system
to set the spi_model as NULL to indicate it should not be instantiated.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Message-Id: <20220305000656.1944589-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used anymore.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the allocation of the flash devices uses the number of
slave selects configured in the SoC realize routine. It is simpler to
use directly the number of FMC devices defined in the machine class
and 1 for spi devices (which is what the SoC does in the back of the
machine).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A memory chunk is allocated with g_new0() and assigned to the variable
'storage'. However, if the branch takes true, there will be only an
error report but not a free operation for 'storage' before function
returns. As a result, a memory leak bug is triggered.
Use g_autofree to fix the issue.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
[ clg: reworked the commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is a Linux kernel bug present until v5.12 that prevents
booting with FEAT_LPA2 enabled. As a workaround for TCG,
disable this feature for machine versions prior to 7.0.
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
When we're using KVM, the PSCI implementation is provided by the
kernel, but QEMU has to tell the guest about it via the device tree.
Currently we look at the KVM_CAP_ARM_PSCI_0_2 capability to determine
if the kernel is providing at least PSCI 0.2, but if the kernel
provides a newer version than that we will still only tell the guest
it has PSCI 0.2. (This is fairly harmless; it just means the guest
won't use newer parts of the PSCI API.)
The kernel exposes the specific PSCI version it is implementing via
the ONE_REG API; use this to report in the dtb that the PSCI
implementation is 1.0-compatible if appropriate. (The device tree
binding currently only distinguishes "pre-0.2", "0.2-compatible" and
"1.0-compatible".)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220224134655.1207865-1-peter.maydell@linaro.org
Support the latest PSCI on TCG and HVF. A 64-bit function called from
AArch32 now returns NOT_SUPPORTED, which is necessary to adhere to SMC
Calling Convention 1.0. It is still not compliant with SMCCC 1.3 since
they do not implement mandatory functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-id: 20220213035753.34577-1-akihiko.odaki@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: update MISMATCH_CHECK checks on PSCI_VERSION macros to match]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AN547 application note URL has changed: update our comment
accordingly. (Rev B is still downloadable from the old URL,
but there is a new Rev C of the document now.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220221094144.426191-1-peter.maydell@linaro.org
With these interfaces missing, TFM would delegate peripherals 0, 1,
2, 3 and 8, and qemu would ignore the delegation of interface 8, as
it thought interface 4 was eth & USB.
This patch corrects this behavior and allows TFM to delegate the
eth & USB peripheral to NS mode.
(The old QEMU behaviour was based on revision B of the AN547
appnote; revision C corrects this error in the documentation,
and this commit brings QEMU in to line with how the FPGA
image really behaves.)
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
Message-id: 20220210210227.3203883-1-jimmy.brisson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added commit message note clarifying that the old behaviour
was a docs issue, not because there were two different versions
of the FPGA image]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmIbOjkACgkQUaNDx8/7
7KHl4w//QySSZtdkk0fLIHg6q4aSeehLZWro5JVRs+ZGtmM6ixi95RNQwEyiM3g6
fHbkgsE3YHh3rnX5KckTPwMq+LctLSebrUtOvHQyTcHckCjwn90Vyaw7hSBROeGz
8Yieb6qda2kEnX61yGlE80go3WDuA2kyRw2bvHOhT5Vzsb2Xq8xflziFv+gHH4NT
Hf/AiCSh6uCILT0JyhZF4Swzip+jDGytryPdBThBtptShyscCgIKb9GqVTVHbWXi
dCe+eDDPUm7npOfP5RmHE249tz+SwS+YejTShewt0FALzglxu/GZI3UNEg0Ays+0
E7uWeSFrgQE5lZvht3Z7Duc0GCGQxYkVwhUtr2e/9dLUIRTrcdj/55h/VgeaSzR5
3RXtbwNAaumE0JdgKXFwmBuPNRNzZa89hrBcvswkcVXtlB2hsWlWLniKJHbafNHk
vOMABrEeWCZYT794J0yFrunCUFPCNUXpPYJJdRBeIktiHzRGJYHraX7i/aJ5ltse
VaDVbEdHaB11H8Y2cQJtjda/zM84DaqGQj9EkQPCRe7w3bnWQLSJ1qcahszV0P+Z
y+DkoFRr3LKVE9dIS/N4gwIBWk5AymqSqAVizQ61rq8ZetUNdgTT12EC39djhATi
OfudYiQKc33gvYOLLFSST2tiv/NK/GfIGc2Ag1qME30NYnam50Q=
=0F2M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220227' into staging
aspeed queue:
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
# gpg: Signature made Sun 27 Feb 2022 08:45:45 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220227:
aspeed/sdmc: Add trace events
aspeed/smc: Add an address mask on segment registers
aspeed: Introduce a create_pca9552() helper
aspeed: rainier: Add strap values taken from hardware
aspeed: rainier: Add i2c LED devices
ast2600: Add Secure Boot Controller model
arm: Remove swift-bmc machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This unifies the way we create the pca9552 devices on the different boards.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This helps quieten booting the current Rainier kernel.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Just a stub that indicates the system has booted in secure boot mode.
Used for testing the driver:
https://lore.kernel.org/all/20211019080608.283324-1-joel@jms.id.au/
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Fixed typo
- Adjusted Copyright dates ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It was scheduled for removal in 7.0.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the BMC attached to the OpenBMC Mori board.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Chris Rauer <crauer@google.com>
Reviewed-by: Ilkyun Choi <ikchoi@google.com>
Message-id: 20220208233104.284425-1-venture@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "hardware version" machinery (qemu_set_hw_version(),
qemu_hw_version(), and the QEMU_HW_VERSION define) is used by fewer
than 10 files. Move it out from osdep.h into a new
qemu/hw-version.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-6-peter.maydell@linaro.org
In the armv7m object, handle clock inputs that aren't connected.
This is always an error for 'cpuclk'. For 'refclk' it is OK for this
to be disconnected, but we need to handle it by not trying to connect
a sourceless-clock to the systick device.
This fixes a bug where on the mps2-an521 and similar boards (which
do not have a refclk) the systick device incorrectly reset with
SYST_CSR.CLKSOURCE 0 ("use refclk") rather than 1 ("use CPU clock").
Cc: qemu-stable@nongnu.org
Reported-by: Richard Petri <git@rpls.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208171643.3486277-1-peter.maydell@linaro.org
For arm boards with an i2c bus which a user could reasonably
want to plug arbitrary devices, add 'imply I2C_DEVICES' to the
Kconfig stanza.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20220208155911.3408455-3-peter.maydell@linaro.org
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We currently miss a bunch of register resets in the device reset
function. This sometimes prevents the guest from rebooting after
a system_reset (with virtio-blk-pci). For instance, we may get
the following errors:
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid read at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
smmuv3-iommu-memory-region-0-0 translation failed for iova=0x13a9d2000(SMMU_EVT_C_BAD_STE)
Invalid write at addr 0x13A9D2000, size 2, region '(null)', reason: rejected
invalid STE
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220202111602.627429-1-eric.auger@redhat.com
Fixes: 10a83cb988 ("hw/arm/smmuv3: Skeleton")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Always call arm_load_kernel() regardless of kernel_filename being
set. This is needed because arm_load_kernel() sets up reset for
the CPUs.
Fixes: 6f16da53ff (hw/arm: versal: Add a virtual Xilinx Versal board)
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20220130110313.4045351-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're using PSCI emulation, we add a /psci node to the device tree
we pass to the guest. At the moment, if the dtb already has a /psci
node in it, we retain it, rather than replacing it. (This behaviour
was added in commit c39770cd63 in 2018.)
This is a problem if the existing node doesn't match our PSCI
emulation. In particular, it might specify the wrong method (HVC vs
SMC), or wrong function IDs for cpu_suspend/cpu_off/etc, in which
case the guest will not get the behaviour it wants when it makes PSCI
calls.
An example of this is trying to boot the highbank or midway board
models using the device tree supplied in the kernel sources: this
device tree includes a /psci node that specifies function IDs that
don't match the (PSCI 0.2 compliant) IDs that QEMU uses. The dtb
cpu_suspend function ID happens to match the PSCI 0.2 cpu_off ID, so
the guest hangs after booting when the kernel tries to idle the CPU
and instead it gets turned off.
Instead of retaining an existing /psci node, delete it entirely
and replace it with a node whose properties match QEMU's PSCI
emulation behaviour. This matches the way we handle /memory nodes,
where we also delete any existing nodes and write in ones that
match the way QEMU is going to behave.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-17-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
The highbank and midway board code includes boot-stub code for
handling secondary CPU boot which keeps the secondaries in a pen
until the primary writes to a known location with the address they
should jump to.
This code is never used, because the boards enable QEMU's PSCI
emulation, so secondary CPUs are kept powered off until the PSCI call
which turns them on, and then start execution from the address given
by the guest in that PSCI call. Delete the unreachable code.
(The code was wrong for midway in any case -- on the Cortex-A15 the
GIC CPU interface registers are at a different offset from PERIPHBASE
compared to the Cortex-A9, and the code baked-in the offsets for
highbank's A9.)
Note that this commit implicitly depends on the preceding "Don't
write secondary boot stub if using PSCI" commit -- the default
secondary-boot stub code overlaps with one of the highbank-specific
bootcode rom blobs, so we must suppress the secondary-boot
stub code entirely, not merely replace the highbank-specific
version with the default.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-15-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Now that we have dealt with the one special case (highbank) that needed
to set both psci_conduit and secure_board_setup, we don't need to
allow that combination any more. It doesn't make sense in general,
so use an assertion to ensure we don't add new boards that do it
by accident without thinking through the consequences.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-13-peter.maydell@linaro.org
Guest code on highbank may make non-PSCI SMC calls in order to
enable/disable the L2x0 cache controller (see the Linux kernel's
arch/arm/mach-highbank/highbank.c highbank_l2c310_write_sec()
function). The ABI for this is documented in kernel commit
8e56130dcb as being borrowed from the OMAP44xx ROM. The OMAP44xx TRM
documents this function ID as having no return value and potentially
trashing all guest registers except SP and PC. For QEMU's purposes
(where our L2x0 model is a stub and enabling or disabling it doesn't
affect the guest behaviour) a simple "do nothing" SMC is fine.
We currently implement this NOP behaviour using a little bit of
Secure code we run before jumping to the guest kernel, which is
written by arm_write_secure_board_setup_dummy_smc(). The code sets
up a set of Secure vectors where the SMC entry point returns without
doing anything.
Now that the PSCI SMC emulation handles all SMC calls (setting r0 to
an error code if the input r0 function identifier is not recognized),
we can use that default behaviour as sufficient for the highbank
cache controller call. (Because the guest code assumes r0 has no
interesting value on exit it doesn't matter that we set it to the
error code). We can therefore delete the highbank board code that
sets secure_board_setup to true and writes the secure-code bootstub.
(Note that because the OMAP44xx ABI puts function-identifiers in
r12 and PSCI uses r0, we only avoid a clash because Linux's code
happens to put the function-identifier in both registers. But this
is true also when the kernel is running on real firmware that
implements both ABIs as far as I can see.)
This change fixes in passing booting on the 'midway' board model,
which has been completely broken since we added support for Hyp
mode to the Cortex-A15 CPU. When we did that boot.c was made to
start running the guest code in Hyp mode; this includes the
board_setup hook, which instantly UNDEFs because the NSACR is
not accessible from Hyp. (Put another way, we never made the
secure_board_setup hook support cope with Hyp mode.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-12-peter.maydell@linaro.org
Change the highbank/midway boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit and start-powered-off
properties on the CPU objects in the board code, and instead set the
psci_conduit field in the arm_boot_info struct to tell the common
boot loader code that we'd like PSCI if the guest is starting at an
EL that it makes sense with (in which case it will set these
properties).
This means that when running guest code at EL3, all the cores
will start execution at once on poweron. This matches the
real hardware behaviour. (A brief description of the hardware
boot process is in the u-boot documentation for these boards:
https://u-boot.readthedocs.io/en/latest/board/highbank/highbank.html#boot-process
-- in theory one might run the 'a9boot'/'a15boot' secure monitor
code in QEMU, though we probably don't emulate enough for that.)
This affects the highbank and midway boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-10-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the virt board code, set the arm_boot_info psci_conduit
field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel or to the generic loader. (EL3 guest code started
via -bios or -pflash was already being run with PSCI emulation
disabled.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-9-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Change the Xilinx ZynqMP-based board xlnx-zcu102 to use the new
boot.c functionality to allow us to enable psci-conduit only if
the guest is being booted in EL1 or EL2, so that if the user runs
guest EL3 firmware code our PSCI emulation doesn't get in its
way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
Note that this means that EL3 guest code will have no way
to power on secondary cores, because we don't model any
kind of power controller that does that on this SoC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-7-peter.maydell@linaro.org
Change the allwinner-h3 based board to use the new boot.c
functionality to allow us to enable psci-conduit only if the guest is
being booted in EL1 or EL2, so that if the user runs guest EL3
firmware code our PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes sense
with.
This affects the orangepi-pc board.
This commit leaves the secondary CPUs in the powered-down state if
the guest is booting at EL3, which is the same behaviour as before
this commit. The secondaries can no longer be started by that EL3
code making a PSCI call but can still be started via the CPU
Configuration Module registers (which we model in
hw/misc/allwinner-cpucfg.c).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-6-peter.maydell@linaro.org
Change the iMX-SoC based boards to use the new boot.c functionality
to allow us to enable psci-conduit only if the guest is being booted
in EL1 or EL2, so that if the user runs guest EL3 firmware code our
PSCI emulation doesn't get in its way.
To do this we stop setting the psci-conduit property on the CPU
objects in the SoC code, and instead set the psci_conduit field in
the arm_boot_info struct to tell the common boot loader code that
we'd like PSCI if the guest is starting at an EL that it makes
sense with.
This affects the mcimx6ul-evk and mcimx7d-sabre boards.
Note that for the mcimx7d board, this means that when running guest
code at EL3 there is currently no way to power on the secondary CPUs,
because we do not currently have a model of the system reset
controller module which should be used to do that for the imx7 SoC,
only for the imx6 SoC. (Previously EL3 code which knew it was
running on QEMU could use a PSCI call to do this.) This doesn't
affect the imx6ul-evk board because it is uniprocessor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220127154639.2090164-5-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Address should be 0x1E631000 and not 0x1E641000 as initially introduced.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/838
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Suggested-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220126083520.4135713-1-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect Micron Xccela mt35xu01g flashes to the OSPI flash memory
controller.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-10-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the OSPI flash memory controller model (including the source and
destination DMA).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-8-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an orgate and 'or' the interrupts from the BBRAM and RTC models.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-3-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In commit d5093d9615 we added a VMStateDescription to
the TYPE_ARMV7M object, to handle migration of its Clocks.
However a cut-and-paste error meant we used the wrong struct
name in the VMSTATE_CLOCK() macro arguments. The result was
that attempting a 'savevm' might result in an assertion
failure.
Cc: qemu-stable@nongnu.org
Buglink: https://gitlab.com/qemu-project/qemu/-/issues/803
Fixes: d5093d9615
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120151609.433555-1-peter.maydell@linaro.org
Now that the devices present in the extended memory map are checked
against the available PA space and disabled when they don't fit,
there is no need to keep the same checks against highmem, as
highmem really is a shortcut for the PA space being 32bit.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-id: 20220114140741.1358263-7-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to only keep the highmem devices that actually fit in
the PA range, check their location against the range and update
highest_gpa if they fit. If they don't, mark them as disabled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-6-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The highmem attribute is nothing but another way to express the
PA range of a VM. To support HW that has a smaller PA range then
what QEMU assumes, pass this PA range to the virt_set_memmap()
function, allowing it to correctly exclude highmem devices
if they are outside of the PA range.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-5-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Even when the VM is configured with highmem=off, the highest_gpa
field includes devices that are above the 4GiB limit.
Similarily, nothing seem to check that the memory is within
the limit set by the highmem=off option.
This leads to failures in virt_kvm_type() on systems that have
a crippled IPA range, as the reported IPA space is larger than
what it should be.
Instead, honor the user-specified limit to only use the devices
at the lowest end of the spectrum, and fail if we have memory
crossing the 4GiB limit.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Message-id: 20220114140741.1358263-4-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe region
using highmem_ecam, let's add a control for the highmem GICv3
redistributor region.
Similarily to highmem_ecam, these redistributors are disabled when
highmem is off.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-3-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Just like we can control the enablement of the highmem PCIe ECAM
region using highmem_ecam, let's add a control for the highmem
PCIe MMIO region.
Similarily to highmem_ecam, this region is disabled when highmem
is off.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220114140741.1358263-2-maz@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This supports virtio-mem-pci device on "virt" platform, by simply
following the implementation on x86.
* This implements the hotplug handlers to support virtio-mem-pci
device hot-add, while the hot-remove isn't supported as we have
on x86.
* The block size is 512MB on ARM64 instead of 128MB on x86.
* It has been passing the tests with various combinations like 64KB
and 4KB page sizes on host and guest, different memory device
backends like normal, transparent huge page and HugeTLB, plus
migration.
Co-developed-by: David Hildenbrand <david@redhat.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-id: 20220111063329.74447-3-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support one cluster level between core and physical package in the
cpu-map of Arm/virt devicetree. This is also consistent with Linux
Doc "Documentation/devicetree/bindings/cpu/cpu-topology.txt".
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220107083232.16256-3-wangyanan55@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM64 machines like Kunpeng Family Server Chips have a level
of hardware topology in which a group of CPU cores share L3
cache tag or L2 cache. For example, Kunpeng 920 typically
has 6 or 8 clusters in each NUMA node (also represent range
of CPU die), and each cluster has 4 CPU cores. All clusters
share L3 cache data, but CPU cores in each cluster share a
local L3 tag.
Running a guest kernel with Cluster-Aware Scheduling on the
Hosts which have physical clusters, if we can design a vCPU
topology with cluster level for guest kernel and then have
a dedicated vCPU pinning, the guest will gain scheduling
performance improvement from cache affinity of CPU cluster.
So let's enable the support for this new parameter on ARM
virt machines. After this patch, we can define a 4-level
CPU hierarchy like: cpus=*,maxcpus=*,sockets=*,clusters=*,
cores=*,threads=*.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20220107083232.16256-2-wangyanan55@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 network device is hidden in the Musicpal
machine. Move it into a new unit file under the hw/net/ directory.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are going to move this code, so fix its style first to avoid:
ERROR: spaces required around that '/' (ctx:VxV)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell 88W8618 is a system-on-chip with an ARM core.
We implement its audio codecs and network interface.
Homogeneous SoC Kconfig are usually defined in the hw/$ARCH
directory. Move it there.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220107184429.423572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generally a guest needs an external source of randomness to properly
enable things like address space randomisation. However in a trusted
boot environment where the firmware will cryptographically verify
components having random data in the DTB will cause verification to
fail. Add a control knob so we can prevent this being added to the
system DTB.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20220105135009.1584676-22-alex.bennee@linaro.org>
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHY2zEPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpCiEH/jv5tHUffDdGz5M2pN7FTWPQ9UAMQZXbn5AS
PPVutOI/B+ILYBuNjYLvMGeq6ymG4/0DM940/jkQwCWD4ku1OG0ReM5T5klUR8lY
df5y1SCDv3Yoq0vxpQCnssKqbgm8Kf9tnAFjni7Lvbu3oo6DCq77m6MWEapLoEUu
IkM+l60NKmHAClnE6RF4KobLa5srIlDTho1iBXH5S39CRF1LvP9NgnYzl7nqiEkq
ZYQEqkKO5XGxZji9banZPJD2kxt1iL7s24QI6OJG2Lz8Hf86b0Yo7XJpmw4ShP9h
Vl1SL3m/HhHSMBuXOb7w/EkCm59b7whXCmoyYBF/GqaxtZkvVnM=
=4VIN
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pci,pc: features,fixes,cleanups
New virtio mem options.
A vhost-user cleanup.
Control over smbios entry point type.
Config interrupt support for vdpa.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 07 Jan 2022 04:30:41 PM PST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (55 commits)
tests: acpi: Add updated TPM related tables
acpi: tpm: Add missing device identification objects
tests: acpi: prepare for updated TPM related tables
virtio/vhost-vsock: don't double close vhostfd, remove redundant cleanup
hw/scsi/vhost-scsi: don't double close vhostfd on error
hw/scsi/vhost-scsi: don't leak vqs on error
docs: reSTify virtio-balloon-stats documentation and move to docs/interop
hw/i386/pc: Add missing property descriptions
acpihp: simplify acpi_pcihp_disable_root_bus
tests: acpi: SLIC: update expected blobs
tests: acpi: add SLIC table test
tests: acpi: whitelist expected blobs before changing them
acpi: fix QEMU crash when started with SLIC table
intel-iommu: correctly check passthrough during translation
virtio-mem: Set "unplugged-inaccessible=auto" for the 7.0 machine on x86
virtio-mem: Support VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
linux-headers: sync VIRTIO_MEM_F_UNPLUGGED_INACCESSIBLE
MAINTAINERS: Add a separate entry for acpi/VIOT tables
virtio: signal after wrapping packed used_idx
virtio-mem: Support "prealloc=on" option
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add missing TPM device identification objects _STR and _UID. They will
appear as files 'description' and 'uid' under Linux sysfs.
Following inspection of sysfs entries for hardware TPMs we chose
uid '1'.
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Ani Sinha <ani@anisinha.ca>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/708
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Shannon Zhao <shannon.zhaosl@gmail.com>
Message-id: 20211223022310.575496-3-stefanb@linux.ibm.com
Message-Id: <20220104175806.872996-3-stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Add the four lm75s behind the mux on bus 13.
Tested by booting the firmware:
lm75 42-0048: hwmon0: sensor 'lm75'
lm75 43-0049: supply vs not found, using dummy regulator
lm75 43-0049: hwmon1: sensor 'lm75'
lm75 44-0048: supply vs not found, using dummy regulator
lm75 44-0048: hwmon2: sensor 'lm75'
lm75 45-0049: supply vs not found, using dummy regulator
lm75 45-0049: hwmon3: sensor 'lm75'
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220102215844.2888833-5-venture@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AST2600 Display Port MCU introduces 0x18000000~0x1803FFFF as it's memory
and io address. If guest machine try to access DPMCU memory, it will
cause a fatal error.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20211210083034.726610-1-troy_lee@aspeedtech.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the enums to match the naming style used by QAPI, and to
use "32" and "64" instead of "20" and "31". This will allow us
to more easily move the enum to the QAPI schema later.
About the naming choice: "SMBIOS 2.1 entry point"/"SMBIOS 3.0
entry point" and "32-bit entry point"/"64-bit entry point" are
synonymous in the SMBIOS specification. However, the phrases
"32-bit entry point" and "64-bit entry point" are used more often.
The new names also avoid confusion between the entry point format
and the actual SMBIOS version reported in the entry point
structure. For example: currently the 32-bit entry point
actually report SMBIOS 2.8 support, not 2.1.
Based on portions of a patch submitted by Daniel P. Berrangé.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-2-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 7.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211217143948.289995-1-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
The aspeed machines connects backends with drive_get_next() in several
counting loops, one of them in a helper function, and a conditional.
Change it to use drive_get() directly. This makes the unit numbers
explicit in the code.
Cc: "Cédric Le Goater" <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-13-armbru@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-zcu102" connects backends with drive_get_next() in two
counting loops, one of them in a helper function. Change it to use
drive_get() directly. This makes the unit numbers explicit in the
code.
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-12-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-zcu102" connects backends with drive_get_next() in
several counting loops. Change it to use drive_get() directly. This
makes the unit numbers explicit in the code.
Cc: Alistair Francis <alistair@alistair23.me>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-11-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To propagate errors to the caller of the pre_plug callback, use the
object_poperty_set*() functions directly instead of the qdev_prop_set*()
helpers.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-5-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We do not support instantiating multiple IOMMUs. Before adding a
virtio-iommu, check that no other IOMMU is present. This will detect
both "iommu=smmuv3" machine parameter and another virtio-iommu instance.
Fixes: 70e89132c9 ("hw/arm/virt: Add the virtio-iommu device tree mappings")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-4-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio-iommu is now supported with ACPI VIOT as well as device tree.
Remove the restriction that prevents from instantiating a virtio-iommu
device under ACPI.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-3-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a virtio-iommu is instantiated, describe it using the ACPI VIOT
table.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20211210170415.583179-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A lot of C files in hw/arm include qemu-common.h when they don't
need anything from it. Drop the include lines.
omap1.c, pxa2xx.c and strongarm.c retain the include because they
use it for the prototype of qemu_get_timedate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Message-id: 20211129200510.1233037-5-peter.maydell@linaro.org
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "xlnx-versal-virt" connects backends with drive_get_next() in
a counting loop. Change it to use drive_get() directly. This makes
the unit numbers explicit in the code.
Cc: Alistair Francis <alistair@alistair23.me>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-9-armbru@redhat.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "mcimx7d-sabre" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-8-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "mcimx6ul-evk" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-7-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "imx25-pdk" connects backends with drive_get_next() in a
counting loop. Change it to use drive_get() directly. This makes the
unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-6-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
The versatile and vexpress machines ("versatileab", "versatilepb",
"vexpress-a9", "vexpress-a15") connect just one or two backends of a
type with drive_get_next(). Change them to use drive_get() directly.
This makes the unit numbers explicit in the code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-5-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
Machine "quanta-gbs-bmc" connects just one backend with
drive_get_next(), but with a helper function. Change it to use
drive_get() directly. This makes the unit numbers explicit in the
code.
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Tyrone Ting <kfting@nuvoton.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-4-armbru@redhat.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
A number of machines connect just one backend with drive_get_next().
Change them to use drive_get() directly. This makes the (zero) unit
number explicit in the code.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Cc: Niek Linnenbank <nieklinnenbank@gmail.com>
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-3-armbru@redhat.com>
ssi_sd_realize() creates an "sd-card" device. This is inappropriate,
and marked FIXME.
Move it to the boards that create these devices. Prior art: commit
eb4f566bbb for device "generic-sdhci", and commit 26c607b86b for
device "pl181".
The device remains not user-creatable, because its users should (and
do) wire up its GPIO chip-select line.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The virt machine has properties to enable MTE and Nested Virtualization
support. However, its check to ensure the backing accel implementation
supports it today only looks for KVM and bails out if it finds it.
Extend the checks to HVF as well as it does not support either today.
This will cause QEMU to print a useful error message rather than
silently ignoring the attempt by the user to enable either MTE or
the Virtualization extensions.
Reported-by: saar amar <saaramar5@gmail.com>
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20211123122859.22452-1-agraf@csgraf.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit d8fb7d0969 ("vl: switch -M parsing to keyval"), machine
parameter definitions cannot use underscores, because keyval_dashify()
transforms them to dashes and the parser doesn't find the parameter.
This affects option default_bus_bypass_iommu which was introduced in the
same release:
$ qemu-system-aarch64 -M virt,default_bus_bypass_iommu=on
qemu-system-aarch64: Property 'virt-6.1-machine.default-bus-bypass-iommu' not found
Rename the parameter to "default-bus-bypass-iommu". Passing
"default_bus_bypass_iommu" is still valid since the underscore are
transformed automatically.
Fixes: 6d7a85483a ("hw/arm/virt: Add default_bus_bypass_iommu machine option")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211026093733.2144161-1-jean-philippe@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* New fp5280g2-bmc board (John)
* Small cleanup in Aspeed SMC model (Cedric)
-----BEGIN PGP SIGNATURE-----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=qbBN
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/clg/tags/pull-aspeed-20211022' into staging
Aspeed patches :
* New fp5280g2-bmc board (John)
* Small cleanup in Aspeed SMC model (Cedric)
# gpg: Signature made Fri 22 Oct 2021 12:55:18 AM PDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/clg/tags/pull-aspeed-20211022:
speed/sdhci: Add trace events
aspeed/smc: Use a container for the flash mmio address space
aspeed: Add support for the fp5280g2-bmc board
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The fp5280g2-bmc is supported by OpenBMC, It's
based on the following device tree
https://github.com/openbmc/linux/blob/dev-5.10/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
Signed-off-by: John Wang <wangzhiqiang02@inspur.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211014064548.934799-1-wangzhiqiang02@inspur.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generate the Processor Properties Topology Table (PPTT) for ARM
virt machines supporting it (>= 6.2).
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20211020142125.7516-8-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Support device tree CPU topology descriptions.
In accordance with the Devicetree Specification, the Linux Doc
"arm/cpus.yaml" requires that cpus and cpu nodes in the DT are
present. And we have already met the requirement by generating
/cpus/cpu@* nodes for members within ms->smp.cpus. Accordingly,
we should also create subnodes in cpu-map for the present cpus,
each of which relates to an unique cpu node.
The Linux Doc "cpu/cpu-topology.txt" states that the hierarchy
of CPUs in a SMP system is defined through four entities and
they are socket/cluster/core/thread. It is also required that
a socket node's child nodes must be one or more cluster nodes.
Given that currently we are only provided with information of
socket/core/thread, we assume there is one cluster child node
in each socket node when creating cpu-map.
Co-developed-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211020142125.7516-4-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
On existing older machine types, without cpu topology described
in ACPI or DT, the guest will populate one by default. With the
topology described, it will read the information and set up its
topology as instructed, but that may not be the same as what was
getting used by default. It's possible that an user application
has a dependency on the default topology and if the default one
gets changed it will probably behave differently.
Based on above consideration we'd better only describe topology
information to the guest on 6.2 and later machine types.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20211020142125.7516-2-wangyanan55@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
ARM SBBR specification mandates DBG2 table (Debug Port Table 2)
since v1.0 (ARM DEN0044F 8.3.1.7 DBG2).
The DBG2 table allows to describe one or more debug ports.
Generate an DBG2 table featuring a single debug port, the PL011.
The DBG2 specification can be found at
"Microsoft Debug Port Table 2 (DBG2)"
https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/acpi-debug-port-table?redirectedfrom=MSDN
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20211019080037.930641-3-eric.auger@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The empty NUMA node, where no memory resides, are allowed. For
example, the following command line specifies two empty NUMA nodes.
With this, QEMU fails to boot because of the conflicting device-tree
node names, as the following error message indicates.
/home/gavin/sandbox/qemu.main/build/qemu-system-aarch64 \
-accel kvm -machine virt,gic-version=host \
-cpu host -smp 4,sockets=2,cores=2,threads=1 \
-m 1024M,slots=16,maxmem=64G \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-numa node,nodeid=0,cpus=0-1,memdev=mem0 \
-numa node,nodeid=1,cpus=2-3,memdev=mem1 \
-numa node,nodeid=2 \
-numa node,nodeid=3
:
qemu-system-aarch64: FDT: Failed to create subnode /memory@80000000: FDT_ERR_EXISTS
As specified by linux device-tree binding document, the device-tree
nodes for these empty NUMA nodes shouldn't be generated. However,
the corresponding NUMA node IDs should be included in the distance
map. The memory hotplug through device-tree on ARM64 isn't existing
so far and it's not necessary to require the user to provide a distance
map. Furthermore, the default distance map Linux generates may even be
sufficient. So this simply skips populating the device-tree nodes for
these empty NUMA nodes to avoid the error, so that QEMU can be started
successfully.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20211015124246.23073-1-gshan@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Upgrade the IORT table from B to E.b specification
revision (ARM DEN 0049E.b).
The SMMUv3 and root complex node have additional
fields. Also unique IORT node identifiers are
introduced: they are generated in sequential order.
They are not cross-referenced though.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20211014115643.756977-3-eric.auger@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
DeviceState.id is a pointer to a string that is stored in the QemuOpts
object DeviceState.opts and freed together with it. We want to create
devices without going through QemuOpts in the future, so make this a
separately allocated string.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211008133442.141332-9-kwolf@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AspeedSMCFlash::size is only used to compute the initial size of the
boot_rom region. Not very useful, so directly call memory_region_size()
instead.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no need to keep a reference of the flash qdev in the AspeedSMCFlash
state: the SPI bus takes ownership and will release its resources. Remove
AspeedSMCFlash::flash.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The characteristics of the Aspeed controllers are described in a
AspeedSMCController structure which is redundant with the
AspeedSMCClass. Move all attributes under the class and adapt the code
to use class attributes instead.
This is a large change but it is functionally equivalent.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-33-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
PS:
Spec is Microsoft hosted, however 1.02 is no where to be found
(MS lists only the current revision) and the current revision is 1.07,
so bring comments in line with 1.07 as this is the only available spec.
There is no content change between originally implemented 1.02
(using QEMU code as reference) and 1.07. The only change is renaming
'Reserved2' field to 'Language', with the same 0 value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-32-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
implicit cast to structure uint8_t member didn't raise error when
assigning value from incorrect enum, but when using build_append_gas()
(next patch) it will error out with (clang):
implicit conversion from enumeration type 'AmlRegionSpace'
to different enumeration type 'AmlAddressSpace'
fix cast error by using correct AML_AS_SYSTEM_MEMORY enum
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-31-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building IORT table use endian agnostic build_append_int_noprefix()
API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210924122802.1455362-30-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-29-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-28-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building MADT table for arm/x86 and use endian agnostic
build_append_int_noprefix() API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-26-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-22-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian conversions
when building SRAT tables for arm/x86 and use endian agnostic
build_append_int_noprefix() API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-18-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
While at it switch to build_append_int_noprefix() to build
table entries (which also removes some manual offset
calculations)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-17-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we have a common structure SMPCompatProps used to store information
about SMP compatibility stuff, so we can also move smp_prefer_sockets
there for cleaner code.
No functional change intended.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-15-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the real SMP hardware topology world, it's much more likely that
we have high cores-per-socket counts and few sockets totally. While
the current preference of sockets over cores in smp parsing results
in a virtual cpu topology with low cores-per-sockets counts and a
large number of sockets, which is just contrary to the real world.
Given that it is better to make the virtual cpu topology be more
reflective of the real world and also for the sake of compatibility,
we start to prefer cores over sockets over threads in smp parsing
since machine type 6.2 for different arches.
In this patch, a boolean "smp_prefer_sockets" is added, and we only
enable the old preference on older machines and enable the new one
since type 6.2 for all arches by using the machine compat mechanism.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210929025816.21076-10-wangyanan55@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Linux spi-imx driver does not work on QEMU. The reason is that the
state of m25p80 loops in STATE_READING_DATA state after receiving
RDSR command, the new command is ignored. Before sending a new command,
CS line should be pulled high to make the state of m25p80 back to IDLE.
Currently the SPI flash CS line is connected to the SPI controller, but
on the real board, it's connected to GPIO3_19. This matches the ecspi1
device node in the board dts.
ecspi1 node in imx6qdl-sabrelite.dtsi:
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash: m25p80@0 {
compatible = "sst,sst25vf016b", "jedec,spi-nor";
spi-max-frequency = <20000000>;
reg = <0>;
};
};
Should connect the SSI_GPIO_CS to GPIO3_19 when adding a spi-nor to
spi1 on sabrelite machine.
Verified this patch on Linux v5.14.
Logs:
# echo "01234567899876543210" > test
# mtd_debug erase /dev/mtd0 0x0 0x1000
Erased 4096 bytes from address 0x00000000 in flash
# mtd_debug write /dev/mtdblock0 0x0 20 test
Copied 20 bytes from test to address 0x00000000 in flash
# mtd_debug read /dev/mtdblock0 0x0 20 test_out
Copied 20 bytes from address 0x00000000 in flash to test_out
# cat test_out
01234567899876543210#
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210927142825.491-1-xchengl.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for ZynqMP eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=3,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 768 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-9-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Xilinx ZynqMP Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=2,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-8-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal eFUSE one-time field-programmable
bit array.
The command argument:
-drive if=pflash,index=1,...
Can be used to optionally connect the bit array to a
backend storage, such that field-programmed values
in one invocation can be made available to next
invocation.
The backend storage must be a seekable binary file, and
its size must be 3072 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-7-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for Versal Battery-Backed RAM (BBRAM)
The command argument:
-drive if=pflash,index=0,...
Can be used to optionally connect the bbram to a backend
storage, such that field-programmed values in one
invocation can be made available to next invocation.
The backend storage must be a seekable binary file, and
its size must be 36 bytes or larger. A file with all
binary 0's is a 'blank'.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Message-id: 20210917052400.1249094-6-tong.ho@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 SoC uses Cortex-A7 cores which support virtualization.
However, today we are configuring QEMU to use HVC as PSCI conduit.
That means HVC calls get trapped into QEMU instead of the guest's own
emulated CPU and thus break the guest's ability to execute virtualization.
Fix this by moving to SMC as conduit, freeing up HYP completely to the VM.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Message-id: 20210920203931.66527-1-agraf@csgraf.de
Fixes: 740dafc0ba ("hw/arm: add Allwinner H3 System-on-Chip")
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The various MPS2 boards implemented in mps2.c have multiple I2C
buses: a bus dedicated to the audio configuration, one for the LCD
touchscreen controller, and two which are connected to the external
Shield expansion connector. Mark the buses which are used only for
board-internal devices as 'full' so that if the user creates i2c
devices on the commandline without specifying a bus name then they
will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-5-peter.maydell@linaro.org
The various MPS2 boards have multiple I2C buses: typically a bus
dedicated to the audio configuration, one for the LCD touchscreen
controller, one for a DDR4 EEPROM, and two which are connected to the
external Shield expansion connector. Mark the buses which are used
only for board-internal devices as 'full' so that if the user creates
i2c devices on the commandline without specifying a bus name then
they will be connected to the I2C controller used for the Shield
connector, where guest software will expect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210903151435.22379-4-peter.maydell@linaro.org
