`muldiv64` would overflow in cases where the final 96-bit value does not
fit in a `uint64_t`. This would result in small values that cause an
interrupt to be triggered much sooner than intended.
The overflow can be detected in most cases by checking if the new value is
smaller than the previous value. If the final result is larger than
`diff` it is either correct or it doesn't matter as it is effectively
infinite anyways.
`next` is an `uint64_t` value, but `timer_mod` takes an `int64_t`. This
resulted in high values such as `UINT64_MAX` being converted to `-1`,
which caused an immediate timer interrupt.
By limiting `next` to `INT64_MAX` no overflow will happen while the
timer will still be effectively set to "infinitely" far in the future.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/493
Signed-off-by: David Hoppenbrouwers <david@salt-inc.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210827152324.5201-1-david@salt-inc.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
It's generic enough to be used from the XIVE2 router and avoid more
duplication.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These will be shared with the XIVE2 router.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210809134547.689560-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In Arm v8.1M the VECTPENDING field in the ICSR has new behaviour: if
the register is accessed NonSecure and the highest priority pending
enabled exception (that would be returned in the VECTPENDING field)
targets Secure, then the VECTPENDING field must read 1 rather than
the exception number of the pending exception. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210723162146.5167-7-peter.maydell@linaro.org
The VECTPENDING field in the ICSR is 9 bits wide, in bits [20:12] of
the register. We were incorrectly masking it to 8 bits, so it would
report the wrong value if the pending exception was greater than 256.
Fix the bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210723162146.5167-6-peter.maydell@linaro.org
The ISCR.ISRPENDING bit is set when an external interrupt is pending.
This is true whether that external interrupt is enabled or not.
This means that we can't use 's->vectpending == 0' as a shortcut to
"ISRPENDING is zero", because s->vectpending indicates only the
highest priority pending enabled interrupt.
Remove the incorrect optimization so that if there is no pending
enabled interrupt we fall through to scanning through the whole
interrupt array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210723162146.5167-5-peter.maydell@linaro.org
Add a space in the message printed when gicr_read*/gicr_write* returns
MEMTX_ERROR in arm_gicv3_redist.c.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210706211432.31902-1-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
icv_eoir_write() and icv_dir_write() ignore invalid virtual IRQ numbers
(like LPIs). The issue is that these functions check against the number
of implemented IRQs (QEMU's default is num_irq=288) which can be lower
than the maximum virtual IRQ number (1020 - 1). The consequence is that
if a hypervisor creates an LR for an IRQ between 288 and 1020, then the
guest is unable to deactivate the resulting IRQ. Note that other
functions that deal with large IRQ numbers, like icv_iar_read, check
against 1020 and not against num_irq.
Fix the checks by using GICV3_MAXIRQ (1020) instead of the number of
implemented IRQs.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-id: 20210702233701.3369-1-ricarkol@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
move kvm files into kvm/
After the reshuffling, update MAINTAINERS accordingly.
Make use of the new directory:
target/s390x/kvm/
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707105324.23400-14-acho@suse.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In commit da6d674e50 we split the NVIC code out from the GIC.
This allowed us to specify the NVIC's default value for the num-irq
property (64) in the usual way in its property list, and we deleted
the previous hack where we updated the value in the state struct in
the instance init function. Remove a stale comment about that hack
which we forgot to delete at that time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210614161243.14211-1-peter.maydell@linaro.org
Commit 382c7160d1 ("hw/intc/arm_gicv3_cpuif: Fix EOIR write access
check logic") added an assert_not_reached() if the guest writes the EOIR
register while no interrupt is active.
It turns out some software does this: EDK2, in
GicV3ExitBootServicesEvent(), unconditionally write EOIR for all
interrupts that it manages. This now causes QEMU to abort when running
UEFI on a VM with GICv3. Although it is UNPREDICTABLE behavior and EDK2
does need fixing, the punishment seems a little harsh, especially since
icc_eoir_write() already tolerates writes of nonexistent interrupt
numbers. Display a guest error and tolerate spurious EOIR writes.
Fixes: 382c7160d1 ("hw/intc/arm_gicv3_cpuif: Fix EOIR write access check logic")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20210604130352.1887560-1-jean-philippe@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Headers should be included from the 'include/' directory,
not from the root directory.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210516205034.694788-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In icc_eoir_write() we assume that we can identify the group of the
IRQ being completed based purely on which register is being written
to and the current CPU state, and that "CPU state matches group
indicated by register" is the only necessary access check.
This isn't correct: if the CPU is not in Secure state then EOIR1 will
only complete Group 1 NS IRQs, but if the CPU is in EL3 it can
complete both Group 1 S and Group 1 NS IRQs. (The pseudocode
ICC_EOIR1_EL1 makes this clear.) We were also missing the logic to
prevent EOIR0 writes completing G0 IRQs when they should not.
Rearrange the logic to first identify the group of the current
highest priority interrupt and then look at whether we should
complete it or ignore the access based on which register was accessed
and the state of the CPU. The resulting behavioural change is:
* EL3 can now complete G1NS interrupts
* G0 interrupt completion is now ignored if the GIC
and the CPU have the security extension enabled and
the CPU is not secure
Reported-by: Chan Kim <ckim@etri.re.kr>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210510150016.24910-1-peter.maydell@linaro.org
Target unicore32 was deprecated in commit 8e4ff4a8d2, v5.2.0. See
there for rationale.
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-3-armbru@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
Update the OpenTitan interrupt layout to match the latest OpenTitan
bitstreams. This involves changing the Ibex PLIC memory layout and the
UART interrupts.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: e92b696f1809c9fa4410da2e9f23c414db5a6960.1617202791.git.alistair.francis@wdc.com
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=N0qr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210504' into staging
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The h_int_reset() function resets the XIVE interrupt controller via
device_legacy_reset(). We know that the interrupt controller does
not have a qbus of its own, so the new device_cold_reset() function
(which resets both the device and its child buses) is equivalent here
to device_legacy_reset() and we can just switch to the new API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210503151849.8766-2-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/sysbus.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210327082804.2259480-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Some compiler versions are smart enough to detect a potentially
uninitialized variable, but are not smart enough to detect that this
cannot happen due to the code flow:
../hw/intc/i8259.c: In function ‘pic_read_irq’:
../hw/intc/i8259.c:203:13: error: ‘irq2’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
203 | irq = irq2 + 8;
| ~~~~^~~~~~~~~~
Restrict irq2 variable use to the inner statement.
Fixes: 78ef2b6989 ("i8259: Reorder intack in pic_read_irq")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210318163059.3686596-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A (generic) copy of the GLUE device we already have for q800 to use with
the m68k-virt machine.
The q800 one would disappear in the future as q800 uses actually the djMEMC
controller.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-4-laurent@vivier.eu>
Implement the goldfish pic device as defined in
https://android.googlesource.com/platform/external/qemu/+/master/docs/GOLDFISH-VIRTUAL-HARDWARE.TXT
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-3-laurent@vivier.eu>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'LM32' config for architecture
specific features. As CONFIG_LM32 is only used to select
peripherals, rename it CONFIG_LM32_DEVICES.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210221225626.2589247-3-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We want to be able to use the 'SH4' config for architecture
specific features. Add more fine-grained selection by adding
a CONFIG_SH_INTC selector for the SH4 interrupt controller.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-4-f4bug@amsat.org>
The userspace local APIC is basically untested and does not support many
features such as TSC deadline timer, x2APIC or PV spinlocks. On the
other hand, the PIT and IOAPIC are okay as they are not tied to
the processor and are tested with -M kernel-irqchip=split.
Therefore, deprecate the local APIC and, with it, limit
-M kernel-irqchip=off to the ISA PC machine type, which does not
have a local APIC at all.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per core ISR is a set of 32-bit registers spaced by 8 bytes.
This patch fixed calculation of it's size and also added check
of alignment at reading & writing.
Fixes: Coverity CID 1438965 and CID 1438967
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Message-Id: <20210112012527.28927-1-jiaxun.yang@flygoat.com>
[PMD: Added Coverity CID]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
ENDs allocated by OPAL for the HW thread VPs are tagged as owned by FW.
Dump the state in 'info pic'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9 systems, PHB controllers signal the XIVE interrupt controller
of a source interrupt notification using a store on a MMIO region. Add
traces for such events.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Per the ARM Generic Interrupt Controller Architecture specification
(document "ARM IHI 0048B.b (ID072613)"), the SGIINTID field is 4 bit,
not 10:
- 4.3 Distributor register descriptions
- 4.3.15 Software Generated Interrupt Register, GICD_SG
- Table 4-21 GICD_SGIR bit assignments
The Interrupt ID of the SGI to forward to the specified CPU
interfaces. The value of this field is the Interrupt ID, in
the range 0-15, for example a value of 0b0011 specifies
Interrupt ID 3.
Correct the irq mask to fix an undefined behavior (which eventually
lead to a heap-buffer-overflow, see [Buglink]):
$ echo 'writel 0x8000f00 0xff4affb0' | qemu-system-aarch64 -M virt,accel=qtest -qtest stdio
[I 1612088147.116987] OPENED
[R +0.278293] writel 0x8000f00 0xff4affb0
../hw/intc/arm_gic.c:1498:13: runtime error: index 944 out of bounds for type 'uint8_t [16][8]'
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior ../hw/intc/arm_gic.c:1498:13
This fixes a security issue when running with KVM on Arm with
kernel-irqchip=off. (The default is kernel-irqchip=on, which is
unaffected, and which is also the correct choice for performance.)
Cc: qemu-stable@nongnu.org
Fixes: CVE-2021-20221
Fixes: 9ee6e8bb85 ("ARMv7 support.")
Buglink: https://bugs.launchpad.net/qemu/+bug/1913916
Buglink: https://bugs.launchpad.net/qemu/+bug/1913917
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210131103401.217160-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Alexander reported an issue in gic_get_current_cpu() using the
fuzzer. Yet another "deref current_cpu with QTest" bug, reproducible
doing:
$ echo readb 0xf03ff000 | qemu-system-arm -M npcm750-evb,accel=qtest -qtest stdio
[I 1611849440.651452] OPENED
[R +0.242498] readb 0xf03ff000
hw/intc/arm_gic.c:63:29: runtime error: member access within null pointer of type 'CPUState' (aka 'struct CPUState')
SUMMARY: UndefinedBehaviorSanitizer: undefined-behavior hw/intc/arm_gic.c:63:29 in
AddressSanitizer:DEADLYSIGNAL
=================================================================
==3719691==ERROR: AddressSanitizer: SEGV on unknown address 0x0000000082a0 (pc 0x5618790ac882 bp 0x7ffca946f4f0 sp 0x7ffca946f4a0 T0)
==3719691==The signal is caused by a READ memory access.
#0 0x5618790ac882 in gic_get_current_cpu hw/intc/arm_gic.c:63:29
#1 0x5618790a8901 in gic_dist_readb hw/intc/arm_gic.c:955:11
#2 0x5618790a7489 in gic_dist_read hw/intc/arm_gic.c:1158:17
#3 0x56187adc573b in memory_region_read_with_attrs_accessor softmmu/memory.c:464:9
#4 0x56187ad7903a in access_with_adjusted_size softmmu/memory.c:552:18
#5 0x56187ad766d6 in memory_region_dispatch_read1 softmmu/memory.c:1426:16
#6 0x56187ad758a8 in memory_region_dispatch_read softmmu/memory.c:1449:9
#7 0x56187b09e84c in flatview_read_continue softmmu/physmem.c:2822:23
#8 0x56187b0a0115 in flatview_read softmmu/physmem.c:2862:12
#9 0x56187b09fc9e in address_space_read_full softmmu/physmem.c:2875:18
#10 0x56187aa88633 in address_space_read include/exec/memory.h:2489:18
#11 0x56187aa88633 in qtest_process_command softmmu/qtest.c:558:13
#12 0x56187aa81881 in qtest_process_inbuf softmmu/qtest.c:797:9
#13 0x56187aa80e02 in qtest_read softmmu/qtest.c:809:5
current_cpu is NULL because QTest accelerator does not use CPU.
Fix by skipping the check and returning the first CPU index when
QTest accelerator is used, similarly to commit c781a2cc42
("hw/i386/vmport: Allow QTest use without crashing").
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-id: 20210128161417.3726358-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 34d0831f38 the ppc-uic device was added, with a dcr-base
property. The intention was that the default value of dcr-base should be
the one that most of our boards need, so that in the common case they
don't need to specify a property value.
All QEMU boards with a UIC use a dcr-base of 0xc0, with the exception of
sam460ex which has four UICs and so puts them at 0xc0, 0xd0, 0xe0, 0xf0.
So 0xc0 is the obvious right choice for the default dcr-base.
The board code conversions in commits 0270d74ef8 (bamboo) and
c5ac9dc64f (virtex_ml507) assumed that default was 0xc0. Unfortunately
the actual default in 34d0831f38 was 0x30, by mistake, so the
bamboo and virtex_ml507 boards were broken as they were converted
away from ppcuic_init() (which always specifies the dcr_base property
value explicitly).
Set the default dcr-base to 0xc0 as was intended, fixing bamboo and
virtex_ml507.
Fixes: 34d0831f38
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210111213007.7381-1-peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
The CCR is a register most of whose bits are banked between security
states but where BFHFNMIGN is not, and we keep it in the non-secure
entry of the v7m.ccr[] array. The logic which tries to handle this
bit fails to implement the "RAZ/WI from Nonsecure if AIRCR.BFHFNMINS
is zero" requirement; correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201210201433.26262-2-peter.maydell@linaro.org
Correct the indexing into s->cpu_ctlr for vCPUs.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20201214222154.3480243-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the GRLIB_IRQMP device is used in one place (the leon3 board),
but instead of the device providing inbound gpio lines for the board
to wire up, the board code itself calls qemu_allocate_irqs() with
the handler function being a set_irq function defined in the code
for the device.
Refactor this into the standard setup of a device having input
gpio lines.
This fixes a trivial Coverity memory leak report (the leon3
board code leaks the IRQ array returned from qemu_allocate_irqs()).
Fixes: Coverity CID 1421922
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212144134.29594-2-peter.maydell@linaro.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=7Eiy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210106' into staging
ppc patch queue 2021-01-06
First pull request for 2021, which has a bunch of things accumulated
over the holidays. Includes:
* A number of cleanups to sam460ex and ppc440 code from BALATON Zoltan
* Several fixes for builds with --without-default-devices from Greg Kurz
* Fixes for some DRC reset problems from Greg Kurz
* QOM conversion of the PPC 4xx UIC devices from Peter Maydell
* Some other assorted fixes and cleanups
# gpg: Signature made Wed 06 Jan 2021 03:33:19 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210106: (22 commits)
ppc440_pcix: Fix up pci config access
ppc440_pcix: Fix register write trace event
ppc440_pcix: Improve comment for IRQ mapping
sam460ex: Remove FDT_PPC dependency from KConfig
ppc4xx: Move common dependency on serial to common option
pnv: Fix reverse dependency on PCI express root ports
ppc: Simplify reverse dependencies of POWERNV and PSERIES on XICS and XIVE
ppc: Fix build with --without-default-devices
spapr: Add drc_ prefix to the DRC realize and unrealize functions
spapr: Use spapr_drc_reset_all() at machine reset
spapr: Introduce spapr_drc_reset_all()
spapr: Fix reset of transient DR connectors
spapr: Call spapr_drc_reset() for all DRCs at CAS
spapr: Fix buffer overflow in spapr_numa_associativity_init()
spapr: Allow memory unplug to always succeed
spapr: Fix DR properties of the root node
spapr/xive: Make spapr_xive_pic_print_info() static
spapr: DRC lookup cannot fail
hw/ppc/ppc440_bamboo: Drop use of ppcuic_init()
hw/ppc/virtex_ml507: Drop use of ppcuic_init()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Have PSERIES to select XICS and XIVE, and directly check PSERIES
in hw/intc/meson.build to enable build of the XICS and XIVE sPAPR
backends, like POWERNV already does. This allows to get rid of the
intermediate XICS_SPAPR and XIVE_SPAPR.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160883057560.253005.4206568349917633920.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Linking of the qemu-system-ppc64 fails on a POWER9 host when
--without-default-devices is passed to configure:
$ ./configure --without-default-devices \
--target-list=ppc64-softmmu && make
...
libqemu-ppc64-softmmu.fa.p/hw_ppc_e500.c.o: In function `ppce500_init_mpic_kvm':
/home/greg/Work/qemu/qemu-ppc/build/../hw/ppc/e500.c:777: undefined reference to `kvm_openpic_connect_vcpu'
libqemu-ppc64-softmmu.fa.p/hw_ppc_spapr_irq.c.o: In function `spapr_irq_check':
/home/greg/Work/qemu/qemu-ppc/build/../hw/ppc/spapr_irq.c:189: undefined reference to `xics_kvm_has_broken_disconnect'
libqemu-ppc64-softmmu.fa.p/hw_intc_spapr_xive.c.o: In function `spapr_xive_post_load':
/home/greg/Work/qemu/qemu-ppc/build/../hw/intc/spapr_xive.c:530: undefined reference to `kvmppc_xive_post_load'
... and tons of other symbols belonging to the KVM backend of the
openpic, XICS and XIVE interrupt controllers.
It turns out that OPENPIC_KVM, XICS_KVM and XIVE_KVM are marked
to depend on KVM but this has no effect when minikconf runs in
allnoconfig mode. Such reverse dependencies should rather be
handled with a 'select' statement, eg.
config OPENPIC
select OPENPIC_KVM if KVM
or even better by getting rid of the intermediate _KVM config
and directly checking CONFIG_KVM in the meson.build file:
specific_ss.add(when: ['CONFIG_KVM', 'CONFIG_OPENPIC'],
if_true: files('openpic_kvm.c'))
Go for the latter with OPENPIC, XICS and XIVE.
This went unnoticed so far because CI doesn't test the build with
--without-default-devices and KVM enabled on a POWER host.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160883056791.253005.14924294027763955653.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently the PPC UIC ("Universal Interrupt Controller") is implemented
as a non-QOM device in ppc4xx_devs.c. Convert it to a proper QOM device
in hw/intc.
The ppcuic_init() function is retained for the moment with its current
interface; in subsequent commits this will be tidied up to avoid the
allocation of an irq array.
This conversion adds VMState support.
It leaves the LOG_UIC() macro as-is to maximise the extent to which
this is simply code-movement rather than a rewrite (in new code it
would be better to use tracepoints).
The default property values for dcr-base and use-vectors are set to
match those use by most of our boards with a UIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201212001537.24520-3-peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As suggested by Philippe Mathieu-Daudé, rework Loongson's liointc:
1, Move macro definitions to loongson_liointc.h;
2, Remove magic values and use macros instead;
3, Replace dead D() code by trace events.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201221110538.3186646-2-chenhuacai@kernel.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
-----BEGIN PGP SIGNATURE-----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=vGLy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2020-12-19' into staging
QAPI patches patches for 2020-12-19
# gpg: Signature made Sat 19 Dec 2020 09:40:05 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2020-12-19: (33 commits)
qobject: Make QString immutable
block: Use GString instead of QString to build filenames
keyval: Use GString to accumulate value strings
json: Use GString instead of QString to accumulate strings
migration: Replace migration's JSON writer by the general one
qobject: Factor JSON writer out of qobject_to_json()
qobject: Factor quoted_str() out of to_json()
qobject: Drop qstring_get_try_str()
qobject: Drop qobject_get_try_str()
Revert "qobject: let object_property_get_str() use new API"
block: Avoid qobject_get_try_str()
qmp: Fix tracing of non-string command IDs
qobject: Move internals to qobject-internal.h
hw/rdma: Replace QList by GQueue
Revert "qstring: add qstring_free()"
qobject: Change qobject_to_json()'s value to GString
qobject: Use GString instead of QString to accumulate JSON
qobject: Make qobject_to_json_pretty() take a pretty argument
monitor: Use GString instead of QString for output buffer
hmp: Simplify how qmp_human_monitor_command() gets output
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 8118f0950f "migration: Append JSON description of migration
stream" needs a JSON writer. The existing qobject_to_json() wasn't a
good fit, because it requires building a QObject to convert. Instead,
migration got its very own JSON writer, in commit 190c882ce2 "QJSON:
Add JSON writer". It tacitly limits numbers to int64_t, and strings
contents to characters that don't need escaping, unlike
qobject_to_json().
The previous commit factored the JSON writer out of qobject_to_json().
Replace migration's JSON writer by it.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When using -Wimplicit-fallthrough in our CFLAGS, the compiler showed warning:
hw/intc/arm_gicv3_kvm.c: In function ‘kvm_arm_gicv3_put’:
hw/intc/arm_gicv3_kvm.c:484:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP0R_EL1(1), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:485:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c:495:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP1R_EL1(2), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:496:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:498:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
kvm_gicc_access(s, ICC_AP1R_EL1(1), ncpu, ®64, true);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/intc/arm_gicv3_kvm.c:499:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c: In function ‘kvm_arm_gicv3_get’:
hw/intc/arm_gicv3_kvm.c:634:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G0][2] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:635:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:637:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G0][1] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:638:9: note: here
default:
^~~~~~~
hw/intc/arm_gicv3_kvm.c:648:39: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G1NS][2] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:649:9: note: here
case 6:
^~~~
hw/intc/arm_gicv3_kvm.c:651:39: warning: this statement may fall through [-Wimplicit-fallthrough=]
c->icc_apr[GICV3_G1NS][1] = reg64;
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~
hw/intc/arm_gicv3_kvm.c:652:9: note: here
default:
^~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20201211152426.350966-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Previously if an interrupt occured during the claim process (after the
interrupt is claimed but before it's completed) it would never be
cleared.
This patch ensures that we also clear the hidden_pending bits as well.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Jackie Ke <jackieke724@hotmail.com>
Message-id: 4e9786084a86f220689123cc8a7837af8fa071cf.1607100423.git.alistair.francis@wdc.com
The Nios2 architecture supports two different interrupt controller
options:
* The IIC (Internal Interrupt Controller) is part of the CPU itself;
it has 32 IRQ input lines and no NMI support. Interrupt status is
queried and controlled via the CPU's ipending and istatus
registers.
* The EIC (External Interrupt Controller) interface allows the CPU
to connect to an external interrupt controller. The interface
allows the interrupt controller to present a packet of information
containing:
- handler address
- interrupt level
- register set
- NMI mode
QEMU does not model an EIC currently. We do model the IIC, but its
implementation is split across code in hw/nios2/cpu_pic.c and
hw/intc/nios2_iic.c. The code in those two files has no state of its
own -- the IIC state is in the Nios2CPU state struct.
Because CPU objects now inherit (indirectly) from TYPE_DEVICE, they
can have GPIO input lines themselves, so we can implement the IIC
directly in the CPU object the same way that real hardware does.
Create named "IRQ" GPIO inputs to the Nios2 CPU object, and make the
only user of the IIC wire up directly to those instead.
Note that the old code had an "NMI" concept which was entirely unused
and also as far as I can see not architecturally correct, since only
the EIC has a concept of an NMI.
This fixes a Coverity-reported trivial memory leak of the IRQ array
allocated in nios2_cpu_pic_init().
Fixes: Coverity CID 1421916
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201129174022.26530-2-peter.maydell@linaro.org
Reviewed-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Wentong Wu <wentong.wu@intel.com>
I have been keeping those logging messages in an ugly form for
while. Make them clean !
Beware not to activate all of them, this is really verbose.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20201123163717.1368450-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Never used from the start.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-6-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR XIVE device is created by the machine in spapr_irq_init().
The latter overrides any value provided by the user with -global for
the "nr-irqs" and "nr-ends" properties with strictly positive values.
It seems reasonable to assume these properties should never be 0,
which wouldn't make much sense by the way.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20201120174646.619395-2-groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The RAS feature has a block of memory-mapped registers at offset
0x5000 within the PPB. For a "minimal RAS" implementation we provide
no error records and so the only registers that exist in the block
are ERRIIDR and ERRDEVID.
The "RAZ/WI for privileged, BusFault for nonprivileged" behaviour
of the "nvic-default" region is actually valid for minimal-RAS,
so the main benefit of providing an explicit implementation of
the register block is more accurate LOG_UNIMP messages, and a
framework for where we could add a real RAS implementation later
if necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-27-peter.maydell@linaro.org
For v8.1M the architecture mandates that CPUs must provide at
least the "minimal RAS implementation" from the Reliability,
Availability and Serviceability extension. This consists of:
* an ESB instruction which is a NOP
-- since it is in the HINT space we need only add a comment
* an RFSR register which will RAZ/WI
* a RAZ/WI AIRCR.IESB bit
-- the code which handles writes to AIRCR does not allow setting
of RES0 bits, so we already treat this as RAZ/WI; add a comment
noting that this is deliberate
* minimal implementation of the RAS register block at 0xe0005000
-- this will be in a subsequent commit
* setting the ID_PFR0.RAS field to 0b0010
-- we will do this when we add the Cortex-M55 CPU model
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-26-peter.maydell@linaro.org
In commit 077d744910 we added code to handle the v8M
requirement that returns from NMI or HardFault forcibly deactivate
those exceptions regardless of what interrupt the guest is trying to
deactivate. Unfortunately this broke the handling of the "illegal
exception return because the returning exception number is not
active" check for those cases. In the pseudocode this test is done
on the exception the guest asks to return from, but because our
implementation was doing this in armv7m_nvic_complete_irq() after the
new "deactivate NMI/HardFault regardless" code we ended up doing the
test on the VecInfo for that exception instead, which usually meant
failing to raise the illegal exception return fault.
In the case for "configurable exception targeting the opposite
security state" we detected the illegal-return case but went ahead
and deactivated the VecInfo anyway, which is wrong because that is
the VecInfo for the other security state.
Rearrange the code so that we first identify the illegal return
cases, then see if we really need to deactivate NMI or HardFault
instead, and finally do the deactivation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-25-peter.maydell@linaro.org
v8.1M introduces a new TRD flag in the CCR register, which enables
checking for stack frame integrity signatures on SG instructions.
This bit is not banked, and is always RAZ/WI to Non-secure code.
Adjust the code for handling CCR reads and writes to handle this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-23-peter.maydell@linaro.org
In v8.1M a REVIDR register is defined, which is at address 0xe00ecfc
and is a read-only IMPDEF register providing implementation specific
minor revision information, like the v8A REVIDR_EL1. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-19-peter.maydell@linaro.org
The FPDSCR register has a similar layout to the FPSCR. In v8.1M it
gains new fields FZ16 (if half-precision floating point is supported)
and LTPSIZE (always reads as 4). Update the reset value and the code
that handles writes to this register accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-16-peter.maydell@linaro.org
For M-profile CPUs, the range from 0xe0000000 to 0xe00fffff is the
Private Peripheral Bus range, which includes all of the memory mapped
devices and registers that are part of the CPU itself, including the
NVIC, systick timer, and debug and trace components like the Data
Watchpoint and Trace unit (DWT). Within this large region, the range
0xe000e000 to 0xe000efff is the System Control Space (NVIC, system
registers, systick) and 0xe002e000 to 0exe002efff is its Non-secure
alias.
The architecture is clear that within the SCS unimplemented registers
should be RES0 for privileged accesses and generate BusFault for
unprivileged accesses, and we currently implement this.
It is less clear about how to handle accesses to unimplemented
regions of the wider PPB. Unprivileged accesses should definitely
cause BusFaults (R_DQQS), but the behaviour of privileged accesses is
not given as a general rule. However, the register definitions of
individual registers for components like the DWT all state that they
are RES0 if the relevant component is not implemented, so the
simplest way to provide that is to provide RAZ/WI for the whole range
for privileged accesses. (The v7M Arm ARM does say that reserved
registers should be UNK/SBZP.)
Expand the container MemoryRegion that the NVIC exposes so that
it covers the whole PPB space. This means:
* moving the address that the ARMV7M device maps it to down by
0xe000 bytes
* moving the off and the offsets within the container of all the
subregions forward by 0xe000 bytes
* adding a new default MemoryRegion that covers the whole container
at a lower priority than anything else and which provides the
RAZWI/BusFault behaviour
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201119215617.29887-2-peter.maydell@linaro.org
When 'j = icu->nr_sense – 1', the 'j < icu->nr_sense' condition is true,
then 'j = icu->nr_sense', the'icu->init_sense[j]' has out-of-bounds access.
The asan showed stack:
ERROR: AddressSanitizer: heap-buffer-overflow on address 0x604000004d7d at pc 0x55852cd26a76 bp 0x7ffe39f26200 sp 0x7ffe39f261f0
READ of size 1 at 0x604000004d7d thread T0
#0 0x55852cd26a75 in rxicu_realize ../hw/intc/rx_icu.c:311
#1 0x55852cf075f7 in device_set_realized ../hw/core/qdev.c:886
#2 0x55852cd4a32f in property_set_bool ../qom/object.c:2251
#3 0x55852cd4f9bb in object_property_set ../qom/object.c:1398
#4 0x55852cd54f3f in object_property_set_qobject ../qom/qom-qobject.c:28
#5 0x55852cd4fc3f in object_property_set_bool ../qom/object.c:1465
#6 0x55852cbf0b27 in register_icu ../hw/rx/rx62n.c:156
#7 0x55852cbf12a6 in rx62n_realize ../hw/rx/rx62n.c:261
#8 0x55852cf075f7 in device_set_realized ../hw/core/qdev.c:886
#9 0x55852cd4a32f in property_set_bool ../qom/object.c:2251
#10 0x55852cd4f9bb in object_property_set ../qom/object.c:1398
#11 0x55852cd54f3f in object_property_set_qobject ../qom/qom-qobject.c:28
#12 0x55852cd4fc3f in object_property_set_bool ../qom/object.c:1465
#13 0x55852cbf1a85 in rx_gdbsim_init ../hw/rx/rx-gdbsim.c:109
#14 0x55852cd22de0 in qemu_init ../softmmu/vl.c:4380
#15 0x55852ca57088 in main ../softmmu/main.c:49
#16 0x7feefafa5d42 in __libc_start_main (/lib64/libc.so.6+0x26d42)
Add the 'ice->src[i].sense' initialize to the default value, and then
process init_sense array to identify which irqs should be level-triggered.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201111141733.2358800-1-kuhn.chenqun@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This series was largely built on the assumption that IPI numbers are
numerically equal to vCPU ids. Even if this happens to be the case
in practice with the default machine settings, this ceases to be true
if VSMT is set to a different value than the number of vCPUs per core.
This causes bogus IPI numbers to be created in KVM from a guest stand
point. This leads to unknow results in the guest, including crashes
or missing vCPUs (see BugLink) and even non-fatal oopses in current
KVM that lacks a check before accessing misconfigured HW (see [1]).
A tentative patch was sent (see [2]) but it seems too complex to be
merged in an RC. Since the original changes are essentially an
optimization, it seems safer to revert them for now. The damage is
done by commit acbdb9956f ("spapr/xive: Allocate IPIs independently
from the other sources") but the previous patches in the series are
really preparatory patches. So this reverts the whole series:
eab0a2d06e ("spapr/xive: Allocate vCPU IPIs from the vCPU contexts")
acbdb9956f ("spapr/xive: Allocate IPIs independently from the other sources")
fa94447a2c ("spapr/xive: Use kvmppc_xive_source_reset() in post_load")
235d3b1162 ("spapr/xive: Modify kvm_cpu_is_enabled() interface")
[1] https://marc.info/?l=kvm-ppc&m=160458409722959&w=4
[2] https://lists.gnu.org/archive/html/qemu-devel/2020-11/msg03626.html
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Fixes: acbdb9956f ("spapr/xive: Allocate IPIs independently from the other sources")
BugLink: https://bugs.launchpad.net/qemu/+bug/1900241
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <160554086275.1325084.12110142252189044646.stgit@bahia.lan>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023122913.19561-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201016145346.27167-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If an interrupt occurs between when we claim and complete an interrupt
we currently drop the interrupt in ibex_plic_irqs_set_pending(). This
somewhat matches hardware that also ignore the interrupt between the
claim and complete process.
In the case of hardware though the physical interrupt line will still
be asserted after we have completed the interrupt. This means we will
still act on the interrupt after the complete process. In QEMU we don't
and instead we drop the interrupt as it is never recorded.
This patch changed the behaviour of the Ibex PLIC so that we save all
interrupts that occur while we are between claiming and completing an
interrupt so that we can act on them after the completition process.
This fixes interrupts being dropped when running Tock on OpenTitain in
QEMU.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: e7bcf98c6925b1e6e7828e7c3f85293a09a65b12.1605136387.git.alistair.francis@wdc.com
After claiming the interrupt by reading the claim register we want to
clear the register to make sure the interrupt doesn't appear at the next
read.
This matches the documentation for the claim register as when an interrupt
is claimed by a target the relevant bit of IP is cleared (which we already
do): https://docs.opentitan.org/hw/ip/rv_plic/doc/index.html
This also matches the current hardware.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 68d4575deef2559b7a747f3bda193fcf43af4558.1604629928.git.alistair.francis@wdc.com
According to the loongson spec
(http://www.loongson.cn/uploadfile/cpu/3B1500/Loongson_3B1500_cpu_user_1.pdf)
and the macro definition(#define R_PERCORE_ISR(x) (0x40 + 0x8 * x)), we know
that the ISR size per CORE is 8, so here we need to divide
(addr - R_PERCORE_ISR(0)) by 8, not 4.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <5FA12391.8090400@huawei.com>
[PMD: Shortened subject]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add sifive_plic vmstate for supporting sifive_plic migration.
Current vmstate framework only supports one structure parameter
as num field to describe variable length arrays, so introduce
num_enables.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Yipeng Yin <yinyipeng1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201026115530.304-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
In gicv3_init_cpuif() we copy the ARMCPU gicv3_maintenance_interrupt
into the GICv3CPUState struct's maintenance_irq field. This will
only work if the board happens to have already wired up the CPU
maintenance IRQ before the GIC was realized. Unfortunately this is
not the case for the 'virt' board, and so the value that gets copied
is NULL (since a qemu_irq is really a pointer to an IRQState struct
under the hood). The effect is that the CPU interface code never
actually raises the maintenance interrupt line.
Instead, since the GICv3CPUState has a pointer to the CPUState, make
the dereference at the point where we want to raise the interrupt, to
avoid an implicit requirement on board code to wire things up in a
particular order.
Reported-by: Jose Martins <josemartins90@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201009153904.28529-1-peter.maydell@linaro.org
Reviewed-by: Luc Michel <luc@lmichel.fr>
Since sifive_plic.h is used by hw/intc/sifive_plic.c,
it has to be in the public include directory. Move it.
Fixes: 84fcf3c151 ("hw/riscv: Move sifive_plic model to hw/intc")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1602578033-68384-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The IRQ values are defined few lines earlier, use them instead of
the magic numbers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-3-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add trace events for GPU and CPU IRQs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201017180731.1165871-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
M-profile CPUs only implement the ID registers as guest-visible if
the CPU implements the Main Extension (all our current CPUs except
the Cortex-M0 do).
Currently we handle this by having the Cortex-M0 leave the ID
register values in the ARMCPU struct as zero, but this conflicts with
our design decision to make QEMU behaviour be keyed off ID register
fields wherever possible.
Explicitly code the ID registers in the NVIC to return 0 if the Main
Extension is not implemented, so we can make the M0 model set the
ARMCPU struct fields to obtain the correct behaviour without those
values becoming guest-visible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-4-peter.maydell@linaro.org
Move the id_pfr0 and id_pfr1 fields into the ARMISARegisters
sub-struct. We're going to want id_pfr1 for an isar_features
check, and moving both at the same time avoids an odd
inconsistency.
Changes other than the ones to cpu.h and kvm64.c made
automatically with:
perl -p -i -e 's/cpu->id_pfr/cpu->isar.id_pfr/' target/arm/*.c hw/intc/armv7m_nvic.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200910173855.4068-3-peter.maydell@linaro.org
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This makes the code consistent with the rest of QOM code in QEMU,
and will make automated conversion to type declaration macros
simpler.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200824215936.2961951-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Separate run of the TypeCheckMacro converter using the --force
flag, for the cases where typedefs weren't found in the same
header nor in typedefs.h.
Generated initially using:
$ ./scripts/codeconverter/converter.py --force -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')
Then each case was manually reviewed, and a comment was added
indicating what's unusual about those type checking
macros/functions. Despite not following the usual pattern, the
changes in this patch were found to be safe.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200831210740.126168-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When QEMU switches to the XIVE interrupt mode, it creates all the
guest interrupts at the level of the KVM device. These interrupts are
backed by real HW interrupts from the IPI interrupt pool of the XIVE
controller.
Currently, this is done from the QEMU main thread, which results in
allocating all interrupts from the chip on which QEMU is running. IPIs
are not distributed across the system and the load is not well
balanced across the interrupt controllers.
Change the vCPU IPI allocation to run from the vCPU context. The
associated XIVE IPI interrupt will be allocated on the chip on which
the vCPU is running and improve distribution of the IPIs in the system.
When the vCPUs are pinned, this will make the IPI local to the chip of
the vCPU. It will reduce rerouting between interrupt controllers and
gives better performance.
Device interrupts are still treated the same. To improve placement, we
would need some information on the chip owning the virtual source or
the HW source in case of a passthrough device but this reuires
changes in PAPR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820134547.2355743-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The vCPU IPIs are now allocated in kvmppc_xive_cpu_connect() when the
vCPU connects to the KVM device and not when all the sources are reset
in kvmppc_xive_source_reset()
This requires extra care for hotplug vCPUs and VM restore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820134547.2355743-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is doing an extra loop but should be equivalent.
It also differentiate the reset of the sources from the restore of the
sources configuration. This will help in allocating the vCPU IPIs
independently.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820134547.2355743-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use to check if a vCPU IPI has been created.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820134547.2355743-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9, the KVM XIVE device uses priority 7 for the escalation
interrupts. On POWER10, the host can use a reduced set of priorities
and KVM will configure the escalation priority to a lower number. In
any case, the guest is allowed to use priorities in a single range :
[ 0 .. (maxprio - 1) ].
Introduce a 'hv-prio' property to represent the escalation priority
number and use it to compute the "ibm,plat-res-int-priorities"
property defining the priority ranges reserved by the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200819130843.2230799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clang static code analyzer show warning:
hw/intc/exynos4210_combiner.c:231:9: warning: Value stored to 'val' is never read
val = s->reg_set[offset >> 2];
The default register return value should be return 'val'.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200827110311.164316-10-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1594631126-36631-1-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Here's my first pull request for qemu-5.2, which has quite a few
accumulated things. Highlights are:
* Preliminary support for POWER10 (Power ISA 3.1) instruction emulation
* Add documentation on the (very confusing) pseries NUMA configuration
* Fix some bugs handling edge cases with XICS, XIVE and kernel_irqchip
* Fix icount for a number of POWER registers
* Many cleanups to error handling in XIVE code
* Validate size of -prom-env data
-----BEGIN PGP SIGNATURE-----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=L9Wi
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20200818' into staging
ppc patch queue 2020-08-18
Here's my first pull request for qemu-5.2, which has quite a few
accumulated things. Highlights are:
* Preliminary support for POWER10 (Power ISA 3.1) instruction emulation
* Add documentation on the (very confusing) pseries NUMA configuration
* Fix some bugs handling edge cases with XICS, XIVE and kernel_irqchip
* Fix icount for a number of POWER registers
* Many cleanups to error handling in XIVE code
* Validate size of -prom-env data
# gpg: Signature made Tue 18 Aug 2020 05:18:36 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20200818: (40 commits)
spapr/xive: Use xive_source_esb_len()
nvram: Exit QEMU if NVRAM cannot contain all -prom-env data
spapr/xive: Simplify error handling of kvmppc_xive_cpu_synchronize_state()
ppc/xive: Simplify error handling in xive_tctx_realize()
spapr/xive: Simplify error handling in kvmppc_xive_connect()
ppc/xive: Fix error handling in vmstate_xive_tctx_*() callbacks
spapr/xive: Fix error handling in kvmppc_xive_post_load()
spapr/kvm: Fix error handling in kvmppc_xive_pre_save()
spapr/xive: Rework error handling of kvmppc_xive_set_source_config()
spapr/xive: Rework error handling in kvmppc_xive_get_queues()
spapr/xive: Rework error handling of kvmppc_xive_[gs]et_queue_config()
spapr/xive: Rework error handling of kvmppc_xive_cpu_[gs]et_state()
spapr/xive: Rework error handling of kvmppc_xive_mmap()
spapr/xive: Rework error handling of kvmppc_xive_source_reset()
spapr/xive: Rework error handling of kvmppc_xive_cpu_connect()
spapr: Simplify error handling in spapr_phb_realize()
spapr/xive: Convert KVM device fd checks to assert()
ppc/xive: Introduce dedicated kvm_irqchip_in_kernel() wrappers
ppc/xive: Rework setup of XiveSource::esb_mmio
target/ppc: Integrate icount to purr, vtb, and tbu40
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch follows what commit aa4d30f661 "riscv: plic: Honour source
priorities" does and ensures that the highest priority interrupt will be
serviced first.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <a697ca8a31eff8eb18a88e09a28206063cf85d48.1595655188.git.alistair.francis@wdc.com>
Once an interrupt has been claimed, but before it has been compelted we
shouldn't receive any more pending interrupts. This patche keeps track
of this to ensure that we don't see any more interrupts until it is
completed.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <394c3f070615ff2b4fab61a1cf9cb48c122913b7.1595655188.git.alistair.francis@wdc.com>
After a claim or a priority change we need to update the pending
interrupts. This is based on the same patch for the SiFive PLIC:
5576582280 "riscv: plic: Add a couple of mising
sifive_plic_update calls"
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cc: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <0693aa700a4c67c49b3f1c973a82b257fdb7198d.1595655188.git.alistair.francis@wdc.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that kvmppc_xive_cpu_get_state() returns negative on error, use that
and get rid of the temporary Error object and error_propagate().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707852916.1489912.8376334685349668124.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that kvmppc_xive_cpu_connect() returns a negative errno on failure,
use that and get rid of the local_err boilerplate.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707852234.1489912.16410314514265848075.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that all these functions return a negative errno on failure, check
that and get rid of the local_err boilerplate.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707851537.1489912.1030839306195472651.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that kvmppc_xive_cpu_get_state() and kvmppc_xive_cpu_set_state()
return negative errnos on failures, use that instead local_err because
it is the recommended practice. Also return that instead of -1 since
vmstate expects negative errnos.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707850840.1489912.14912810818646455474.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that all these functions return a negative errno on failure, check
that because it is preferred to local_err. And most of all, propagate it
because vmstate expects negative errnos.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707850148.1489912.18355118622296682631.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that kvmppc_xive_get_queues() returns a negative errno on failure, check
with that because it is preferred to local_err. And most of all, propagate
it because vmstate expects negative errnos.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707849455.1489912.6034461176847728064.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvm_device_access() returns a negative errno on failure, convert
kvmppc_xive_set_source_config() to use it for error checking. This allows
to get rid of the local_err boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707848764.1489912.17078842252160674523.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvmppc_xive_get_queue_config() has a return value, convert
kvmppc_xive_get_queues() to use it for error checking. This allows
to get rid of the local_err boiler plate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707848069.1489912.14879208798696134531.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvm_device_access() returns a negative errno on failure, convert
kvmppc_xive_get_queue_config() and kvmppc_xive_set_queue_config() to
use it for error checking. This allows to get rid of the local_err
boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707847357.1489912.2032291280645236480.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
kvm_set_one_reg() returns a negative errno on failure, use that instead
of errno. Also propagate it to callers so they can use it to check
for failures and hopefully get rid of their local_err boilerplate.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707846665.1489912.14267225652103441921.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Callers currently check failures of kvmppc_xive_mmap() through the
@errp argument, which isn't a recommanded practice. It is preferred
to use a return value when possible.
Since NULL isn't an invalid address in theory, it seems better to
return MAP_FAILED and to teach callers to handle it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707845972.1489912.719896767746375765.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since kvmppc_xive_source_reset_one() has a return value, convert
kvmppc_xive_source_reset() to use it for error checking. This
allows to get rid of the local_err boiler plate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707845245.1489912.9151822670764690034.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use error_setg_errno() instead of error_setg(strerror()). While here,
use -ret instead of errno since kvm_vcpu_enable_cap() returns a negative
errno on failure.
Use ERRP_GUARD() to ensure that errp can be passed to error_append_hint(),
and get rid of the local_err boilerplate.
Propagate the return value so that callers may use it as well to check
failures.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159707844549.1489912.4862921680328017645.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All callers guard these functions with an xive_in_kernel() helper. Make
it clear that they are only to be called when the KVM XIVE device exists.
Note that the check on xive is dropped in kvmppc_xive_disconnect(). It
really cannot be NULL since it comes from set_active_intc() which only
passes pointers to allocated objects.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <159679994169.876294.11026653581505077112.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Calls to the KVM XIVE device are guarded by kvm_irqchip_in_kernel(). This
ensures that QEMU won't try to use the device if KVM is disabled or if
an in-kernel irqchip isn't required.
When using ic-mode=dual with the pseries machine, we have two possible
interrupt controllers: XIVE and XICS. The kvm_irqchip_in_kernel() helper
will return true as soon as any of the KVM device is created. It might
lure QEMU to think that the other one is also around, while it is not.
This is exactly what happens with ic-mode=dual at machine init when
claiming IRQ numbers, which must be done on all possible IRQ backends,
eg. RTAS event sources or the PHB0 LSI table : only the KVM XICS device
is active but we end up calling kvmppc_xive_source_reset_one() anyway,
which fails. This doesn't cause any trouble because of another bug :
kvmppc_xive_source_reset_one() lacks an error_setg() and callers don't
see the failure.
Most of the other kvmppc_xive_* functions have similar xive->fd
checks to filter out the case when KVM XIVE isn't active. It
might look safer to have idempotent functions but it doesn't
really help to understand what's going on when debugging.
Since we already have all the kvm_irqchip_in_kernel() in place,
also have the callers to check xive->fd as well before calling
KVM XIVE specific code. This is straight-forward for the spapr
specific XIVE code. Some more care is needed for the platform
agnostic XIVE code since it cannot access xive->fd directly.
Introduce new in_kernel() methods in some base XIVE classes
for this purpose and implement them only in spapr.
In all cases, we still need to call kvm_irqchip_in_kernel() so that
compilers can optimize the kvmppc_xive_* calls away when CONFIG_KVM
isn't defined, thus avoiding the need for stubs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159679993438.876294.7285654331498605426.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Depending on whether XIVE is emultated or backed with a KVM XIVE device,
the ESB MMIOs of a XIVE source point to an I/O memory region or a mapped
memory region.
This is currently handled by checking kvm_irqchip_in_kernel() returns
false in xive_source_realize(). This is a bit awkward as we usually
need to do extra things when we're using the in-kernel backend, not
less. But most important, we can do better: turn the existing "xive.esb"
memory region into a plain container, introduce an "xive.esb-emulated"
I/O subregion and rename the existing "xive.esb" subregion in the KVM
code to "xive.esb-kvm". Since "xive.esb-kvm" is added with overlap
and a higher priority, it prevails over "xive.esb-emulated" (ie.
a guest using KVM XIVE will interact with "xive.esb-kvm" instead of
the default "xive.esb-emulated" region.
While here, consolidate the computation of the MMIO region size in
a common helper.
Suggested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159679992680.876294.7520540158586170894.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since this function begins with:
/* The KVM XIVE device is not in use */
if (!xive || xive->fd == -1) {
return;
}
we obviously don't need to check xive->fd again.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159673297296.766512.14780055521619233656.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If the creation of the KVM XIVE device fails for some reasons, the
negative errno ends up in xive->fd, but the rest of the code assumes
that xive->fd either contains an open fd, ie. positive value, or -1.
This doesn't cause any misbehavior except kvmppc_xive_disconnect()
that will try to close(xive->fd) during rollback and likely be
rewarded with an EBADF.
Only set xive->fd with a open fd.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <159673296585.766512.15404407281299745442.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fix some typos in comments about code modeling coalescing points in the
XIVE routing engine (IVRE).
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Message-Id: <1595461434-27725-1-git-send-email-gromero@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The NVIC provides an outbound qemu_irq "SYSRESETREQ" which it signals
when the guest sets the SYSRESETREQ bit in the AIRCR register. This
matches the hardware design (where the CPU has a signal of this name
and it is up to the SoC to connect that up to an actual reset
mechanism), but in QEMU it mostly results in duplicated code in SoC
objects and bugs where SoC model implementors forget to wire up the
SYSRESETREQ line.
Provide a default behaviour for the case where SYSRESETREQ is not
actually connected to anything: use qemu_system_reset_request() to
perform a system reset. This will allow us to remove the
implementations of SYSRESETREQ handling from the boards where that's
exactly what it does, and also fixes the bugs in the board models
which forgot to wire up the signal:
* microbit
* mps2-an385
* mps2-an505
* mps2-an511
* mps2-an521
* musca-a
* musca-b1
* netduino
* netduinoplus2
We still allow the board to wire up the signal if it needs to, in case
we need to model more complicated reset controller logic or to model
buggy SoC hardware which forgot to wire up the line itself. But
defaulting to "reset the system" is more often going to be correct
than defaulting to "do nothing".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200728103744.6909-3-peter.maydell@linaro.org
This is helpful when debugging stuck guest timers.
As we need apic_get_current_count for that, and it is really not
emulation specific, move it to apic_common.c and export it. Fix its
style at this chance as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <e00e2896-ca5b-a929-de7a-8e5762f0c1c2@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When migrate_add_blocker(blocker, &errp) is followed by
error_propagate(errp, err), we can often just as well do
migrate_add_blocker(..., errp).
Do that with this Coccinelle script:
@@
expression blocker, err, errp;
expression ret;
@@
- ret = migrate_add_blocker(blocker, &err);
- if (err) {
+ ret = migrate_add_blocker(blocker, errp);
+ if (ret < 0) {
... when != err;
- error_propagate(errp, err);
...
}
@@
expression blocker, err, errp;
@@
- migrate_add_blocker(blocker, &err);
- if (err) {
+ if (migrate_add_blocker(blocker, errp) < 0) {
... when != err;
- error_propagate(errp, err);
...
}
Double-check @err is not used afterwards. Dereferencing it would be
use after free, but checking whether it's null would be legitimate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-43-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. The previous two commits did that for sufficiently simple
cases with Coccinelle. Do it for several more manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-37-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. The previous commit did that with a Coccinelle script I
consider fairly trustworthy. This commit uses the same script with
the matching of return taken out, i.e. we convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
}
to
if (!foo(..., errp)) {
...
...
}
This is unsound: @err could still be read between afterwards. I don't
know how to express "no read of @err without an intervening write" in
Coccinelle. Instead, I manually double-checked for uses of @err.
Suboptimal line breaks tweaked manually. qdev_realize() simplified
further to placate scripts/checkpatch.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-36-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
Loongson-3 has an integrated liointc (Local I/O Interrupt Controller).
It is similar to Goldfish interrupt controller, but more powerful (e.g.,
it can route external interrupt to multi-cores).
Documents about Loongson-3's liointc:
1, https://wiki.godson.ac.cn/ip_block:liointc;
2, The "I/O中断" section of Loongson-3's user mannual, part 1.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Message-Id: <1592995531-32600-3-git-send-email-chenhc@lemote.com>
This implementation supported only ICUa.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-15-ysato@users.sourceforge.jp>
[PMD: Fill VMStateField for migration, cover files in MAINTAINERS]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Ibex core contains a PLIC that although similar to the RISC-V spec
is not RISC-V spec compliant.
This patch implements a Ibex PLIC in a somewhat generic way.
As the current RISC-V PLIC needs tidying up, my hope is that as the Ibex
PLIC move towards spec compliance this PLIC implementation can be
updated until it can replace the current PLIC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
These are init/realize pairs produced by the previous commit's
Coccinelle script where the argument test doesn't quite match. They
need even more careful review.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-50-armbru@redhat.com>
