LoongArch system has iocsr address space, most iocsr registers are
per-board, however some iocsr register spaces banked for percpu such
as ipi mailbox and extioi interrupt status. For banked iocsr space,
each cpu has the same iocsr space, but separate data.
This patch changes iocsr address space per-board rather percpu,
for iocsr registers specified for cpu, MemTxAttrs.requester_id
can be parsed for the cpu. With this patches, the total address space
on board will be simple, only iocsr address space and system memory,
rather than the number of cpu and system memory.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
There are two interface pairs for MemoryRegionOps, read/write and
read_with_attrs/write_with_attrs. The later is better for ipi device
emulation since initial cpu can be parsed from attrs.requester_id.
And requester_id can be overrided for IOCSR_IPI_SEND and mail_send
function when it is to forward message to another vcpu.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231215100333.3933632-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Add kvm.c into meson.build to compile it when kvm
is configed. Meanwhile in meson.build, we set the
kvm_targets to loongarch64-softmmu when the cpu is
loongarch. And fix the compiling error when config
is enable-kvm,disable-tcg.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-10-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement loongarch kvm set vcpu interrupt interface,
when a irq is set in vcpu, we use the KVM_INTERRUPT
ioctl to set intr into kvm.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-ID: <20240105075804.1228596-9-zhaotianrui@loongson.cn>
[PMD: Split from bigger patch, part 2]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240110094152.52138-2-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
In preparation of supporting KVM in the next commit.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-ID: <20240105075804.1228596-9-zhaotianrui@loongson.cn>
[PMD: Split from bigger patch, part 1]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240110094152.52138-1-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement kvm_arch_handle_exit for loongarch. In this
function, the KVM_EXIT_LOONGARCH_IOCSR is handled,
we read or write the iocsr address space by the addr,
length and is_write argument in kvm_run.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-8-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement kvm_arch_init_vcpu interface for loongarch,
in this function, we register VM change state handler.
And when VM state changes to running, the counter value
should be put into kvm to keep consistent with kvm,
and when state change to stop, counter value should be
refreshed from kvm.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-7-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement the kvm_arch_init of loongarch, in the function, the
KVM_CAP_MP_STATE cap is checked by kvm ioctl.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-6-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement kvm_arch_get/set_registers interfaces, many regs
can be get/set in the function, such as core regs, csr regs,
fpu regs, mp state, etc.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Change-Id: Ia8fc48fe08b1768853f7729e77d37cdf270031e4
Message-Id: <20240105075804.1228596-5-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Supplement vcpu env initial when vcpu reset, including
init vcpu CSR_CPUID,CSR_TID to cpu->cpu_index. The two
regs will be used in kvm_get/set_csr_ioctl.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-4-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Define some functions in target/loongarch/kvm/kvm.c,
such as kvm_arch_put_registers, kvm_arch_get_registers
and kvm_arch_handle_exit, etc. which are needed by
kvm/kvm-all.c. Now the most functions has no content
and they will be implemented in the next patches.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Signed-off-by: xianglai li <lixianglai@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-3-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Use the scripts/update-linux-headers.sh to synchronize linux
headers from linux v6.7.0-rc8. We mainly want to add the
loongarch linux headers and then add the loongarch kvm support
based on it.
Signed-off-by: Tianrui Zhao <zhaotianrui@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240105075804.1228596-2-zhaotianrui@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
* Make vector whole-register move (vmv) depend on vtype register
* Fix th.dcache.cval1 priviledge check
* Don't allow write mstatus_vs without RVV
* Use hwaddr instead of target_ulong for RV32
* Fix machine IDs QOM getters\
* Fix KVM reg id sizes
* ACPI: Enable AIA, PLIC and update RHCT
* Fix the interrupts-extended property format of PLIC
* Add support for Zacas extension
* Add amocas.[w,d,q] instructions
* Document acpi parameter of virt machine
* RVA22 profiles support
* Remove group setting of KVM AIA if the machine only has 1 socket
* Add RVV CSRs to KVM
* sifive_u: Update S-mode U-Boot image build instructions
* Upgrade OpenSBI from v1.3.1 to v1.4
* pmp: Ignore writes when RW=01 and MML=0
* Assert that the CSR numbers will be correct
* Don't adjust vscause for exceptions
* Ensure mideleg is set correctly on reset
-----BEGIN PGP SIGNATURE-----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=5K9J
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20240110' of https://github.com/alistair23/qemu into staging
RISC-V PR for 9.0
* Make vector whole-register move (vmv) depend on vtype register
* Fix th.dcache.cval1 priviledge check
* Don't allow write mstatus_vs without RVV
* Use hwaddr instead of target_ulong for RV32
* Fix machine IDs QOM getters\
* Fix KVM reg id sizes
* ACPI: Enable AIA, PLIC and update RHCT
* Fix the interrupts-extended property format of PLIC
* Add support for Zacas extension
* Add amocas.[w,d,q] instructions
* Document acpi parameter of virt machine
* RVA22 profiles support
* Remove group setting of KVM AIA if the machine only has 1 socket
* Add RVV CSRs to KVM
* sifive_u: Update S-mode U-Boot image build instructions
* Upgrade OpenSBI from v1.3.1 to v1.4
* pmp: Ignore writes when RW=01 and MML=0
* Assert that the CSR numbers will be correct
* Don't adjust vscause for exceptions
* Ensure mideleg is set correctly on reset
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmWeW8kACgkQr3yVEwxT
# gBMB3BAAtpb7dC/NqDOjo/LjGf81wYUnF0KcfJUIbuHEM9S03mKJEvngV/sUhg+A
# fzsoJazijQZk2+Y02WLT/o+ppRDegb4P6n54Nn13xr024Dn2jf45+EKDLI+vtU5y
# lhwp/LH3SEo2MM/Qr0njl8+jJ7W9adhZeK6x+NFaLaQJ291xupbcwEnScdv2bPAo
# gvbM6yrfUoZ25MsQKIDGssozdGRwOD/keAT0q8C0gKDamqXBDrI80BOVhRms+uLm
# R33DXsAegPKluJTa9gfaWFI0eK34WHXRvSIjE36nZlGNNgqLAVdM2/QozMVz4cKA
# Ymz1nzqB9HeSn1pM4KCK/Y3LH89qLGWtyHYgldiDXA/wSyKajwkbXSWFOT9gPDqV
# i+5BRDvU0zIeMIt+ROqNKgx1Hry6U2aycMNsdHTmygJbGEpiTaXuES5tt+LKsyHe
# w/7a6wPd/kh9LQhXYQ4qbn7L534tWvn8zWyvKLZLxmYPcOn6SdjFbKWmk5ARky2W
# sx9ojn9ANlYaLfzQ3TMRcIhWD6n8Si3KFNiQ3353E8xkRkyfu0WHyXAy8/kIc5UT
# nScO2YD68XkdkcLF6uLUKuGiVZXFWXRY1Ttz9tvEmBckVsg6TIkoMONHeUWNP7ly
# A0bJwN5qEOk6XIYKHWwX5UzvkcfUpOb5VmuLuv3gRoNX0A7/+fc=
# =5K9J
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 10 Jan 2024 08:56:41 GMT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20240110' of https://github.com/alistair23/qemu: (65 commits)
target/riscv: Ensure mideleg is set correctly on reset
target/riscv: Don't adjust vscause for exceptions
target/riscv: Assert that the CSR numbers will be correct
target/riscv: pmp: Ignore writes when RW=01 and MML=0
roms/opensbi: Upgrade from v1.3.1 to v1.4
docs/system/riscv: sifive_u: Update S-mode U-Boot image build instructions
target/riscv/kvm: add RVV and Vector CSR regs
target/riscv/kvm: do PR_RISCV_V_SET_CONTROL during realize()
linux-headers: riscv: add ptrace.h
linux-headers: Update to Linux v6.7-rc5
target/riscv/kvm.c: remove group setting of KVM AIA if the machine only has 1 socket
target/riscv: add rva22s64 cpu
target/riscv: add RVA22S64 profile
target/riscv: add 'parent' in profile description
target/riscv: add satp_mode profile support
target/riscv/cpu.c: add riscv_cpu_is_32bit()
target/riscv/cpu.c: finalize satp_mode earlier
target/riscv: add priv ver restriction to profiles
target/riscv: implement svade
target/riscv: add 'rva22u64' CPU
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bits 10, 6, 2 and 12 of mideleg are read only 1 when the Hypervisor is
enabled. We currently only set them on accesses to mideleg, but they
aren't correctly set on reset. Let's ensure they are always the correct
value.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1617
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240108001328.280222-4-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We have been incorrectly adjusting both the interrupt and exception
cause when using the hypervisor extension and trapping to VS-mode. This
patch changes the conditional to ensure we only adjust the cause for
interrupts and not exceptions.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1708
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240108001328.280222-3-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The CSRs will always be between either CSR_MHPMCOUNTER3 and
CSR_MHPMCOUNTER31 or CSR_MHPMCOUNTER3H and CSR_MHPMCOUNTER31H.
So although ctr_index can't be negative, Coverity doesn't know this and
it isn't obvious to human readers either. Let's add an assert to ensure
that Coverity knows the values will be within range.
To simplify the code let's also change the RV32 adjustment.
Fixes: Coverity CID 1523910
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240108001328.280222-2-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch changes behavior on writing RW=01 to pmpcfg with MML=0.
RWX filed is form of collective WARL with the combination of
pmpcfg.RW=01 remains reserved for future standard use.
According to definition of WARL writing the CSR has no other side
effect. But current implementation change architectural state and
change system behavior. After writing we will get unreadable-unwriteble
region regardless on the previous state.
On the other side WARL said that we should read legal value and nothing
says about what we should write. Current behavior change system state
regardless of whether we read this register or not.
Fixes: ac66f2f0 ("target/riscv: pmp: Ignore writes when RW=01")
Signed-off-by: Ivan Klokov <ivan.klokov@syntacore.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231220153205.11072-1-ivan.klokov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, the documentation outlines the process for building the
S-mode U-Boot image using `make menuconfig` and manual actions within
the menuconfig UI. However, this approach is fragile due to Kconfig
options potentially changing across different releases. For example,
CONFIG_OF_PRIOR_STAGE has been replaced by CONFIG_BOARD since v2022.01
release, and CONFIG_TEXT_BASE has been moved to the 'General setup'
menu from the 'Boot options' menu in v2024.01 release.
This update aims to make the S-mode U-Boot image build instructions
future-proof. It leverages the 'config' script provided in the U-Boot
source tree to edit the .config file, followed by a `make olddefconfig`.
Validated with U-Boot v2024.01 release.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240104071523.273702-1-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add support for RVV and Vector CSR KVM regs vstart, vl and vtype.
Support for vregs[] requires KVM side changes and an extra reg (vlenb)
and will be added later.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218204321.75757-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux RISC-V vector documentation (Document/arch/riscv/vector.rst)
mandates a prctl() in order to allow an userspace thread to use the
Vector extension from the host.
This is something to be done in realize() time, after init(), when we
already decided whether we're using RVV or not. We don't have a
realize() callback for KVM yet, so add kvm_cpu_realize() and enable RVV
for the thread via PR_RISCV_V_SET_CONTROL.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218204321.75757-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
KVM vector support for RISC-V requires the linux-header ptrace.h.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218204321.75757-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We'll add a new RISC-V linux-header file, but first let's update all
headers.
Headers for 'asm-loongarch' were added in this update.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218204321.75757-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The emulated AIA within the Linux kernel restores the HART index
of the IMSICs according to the configured AIA settings. During
this process, the group setting is used only when the machine
partitions harts into groups. It's unnecessary to set the group
configuration if the machine has only one socket, as its address
space might not contain the group shift.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231218090543.22353-2-yongxuan.wang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add a new profile CPU 'rva22s64' to work as an alias of
-cpu rv64i,rva22s64
Like the existing rva22u64 CPU already does with the RVA22U64 profile.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-27-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RVA22S64 profile consists of the following:
- all mandatory extensions of RVA22U64;
- priv spec v1.12.0;
- satp mode sv39;
- Ssccptr, a cache related named feature that we're assuming always
enable since we don't implement a cache;
- Other named features already implemented: Sstvecd, Sstvala,
Sscounterenw;
- the new Svade named feature that was recently added.
Most of the work is already done, so this patch is enough to implement
the profile.
After this patch, the 'rva22s64' user flag alone can be used with the
rva64i CPU to boot Linux:
-cpu rv64i,rva22s64=true
This is the /proc/cpuinfo with this profile enabled:
# cat /proc/cpuinfo
processor : 0
hart : 0
isa : rv64imafdc_zicbom_zicbop_zicboz_zicntr_zicsr_zifencei_zihintpause_zihpm_zfhmin_zca_zcd_zba_zbb_zbs_zkt_svinval_svpbmt
mmu : sv39
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-26-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Certain S-mode profiles, like RVA22S64 and RVA23S64, mandate all the
mandatory extensions of their respective U-mode profiles. RVA22S64
includes all mandatory extensions of RVA22U64, and the same happens with
RVA23 profiles.
Add a 'parent' field to allow profiles to enable other profiles. This
will allow us to describe S-mode profiles by specifying their parent
U-mode profile, then adding just the S-mode specific extensions.
We're naming the field 'parent' to consider the possibility of other
uses (e.g. a s-mode profile including a previous s-mode profile) in the
future.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-25-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
'satp_mode' is a requirement for supervisor profiles like RVA22S64.
User-mode/application profiles like RVA22U64 doesn't care.
Add 'satp_mode' to the profile description. If a profile requires it,
set it during cpu_set_profile(). We'll also check it during finalize()
to validate if the running config implements the profile.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-24-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Next patch will need to retrieve if a given RISCVCPU is 32 or 64 bit.
The existing helper riscv_is_32bit() (hw/riscv/boot.c) will always check
the first CPU of a given hart array, not any given CPU.
Create a helper to retrieve the info for any given CPU, not the first
CPU of the hart array. The helper is using the same 32 bit check that
riscv_cpu_satp_mode_finalize() was doing.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-23-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Profiles will need to validate satp_mode during their own finalize
methods. This will occur inside riscv_tcg_cpu_finalize_features() for
TCG. Given that satp_mode does not have any pre-req from the accelerator
finalize() method, it's safe to finalize it earlier.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-22-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some profiles, like RVA22S64, has a priv_spec requirement.
Make this requirement explicit for all profiles. We'll validate this
requirement finalize() time and, in case the user chooses an
incompatible priv_spec while activating a profile, a warning will be
shown.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-21-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
'svade' is a RVA22S64 profile requirement, a profile we're going to add
shortly. It is a named feature (i.e. not a formal extension, not defined
in riscv,isa DT at this moment) defined in [1] as:
"Page-fault exceptions are raised when a page is accessed when A bit is
clear, or written when D bit is clear.".
As far as the spec goes, 'svade' is one of the two distinct modes of
handling PTE_A and PTE_D. The other way, i.e. update PTE_A/PTE_D when
they're cleared, is defined by the 'svadu' extension. Checking
cpu_helper.c, get_physical_address(), we can verify that QEMU is
compliant with that: we will update PTE_A/PTE_D if 'svadu' is enabled,
or throw a page-fault exception if 'svadu' isn't enabled.
So, as far as we're concerned, 'svade' translates to 'svadu must be
disabled'.
We'll implement it like 'zic64b': an internal flag that profiles can
enable. The flag will not be exposed to users.
[1] https://github.com/riscv/riscv-profiles/blob/main/profiles.adoc
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-20-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This CPU was suggested by Alistair [1] and others during the profile
design discussions. It consists of the bare 'rv64i' CPU with rva22u64
enabled by default, like an alias of '-cpu rv64i,rva22u64=true'.
Users now have an even easier way of consuming this user-mode profile by
doing '-cpu rva22u64'. Extensions can be enabled/disabled at will on top
of it.
We can boot Linux with this "user-mode" CPU by doing:
-cpu rva22u64,sv39=true,s=true,zifencei=true
[1] https://lore.kernel.org/qemu-riscv/CAKmqyKP7xzZ9Sx=-Lbx2Ob0qCfB7Z+JO944FQ2TQ+49mqo0q_Q@mail.gmail.com/
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-19-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Expose all profile flags for all CPUs when executing
query-cpu-model-expansion. This will allow callers to quickly determine
if a certain profile is implemented by a given CPU. This includes vendor
CPUs - the fact that they don't have profile user flags doesn't mean
that they don't implement the profile.
After this change it's possible to quickly determine if our stock CPUs
implement the existing rva22u64 profile. Here's a few examples:
$ ./build/qemu-system-riscv64 -S -M virt -display none
-qmp tcp:localhost:1234,server,wait=off
$ ./scripts/qmp/qmp-shell localhost:1234
Welcome to the QMP low-level shell!
Connected to QEMU 8.1.50
- As expected, the 'max' CPU implements the rva22u64 profile.
(QEMU) query-cpu-model-expansion type=full model={"name":"max"}
{"return": {"model":
{"name": "rv64", "props": {... "rva22u64": true, ...}}}}
- rv64 is missing "zba", "zbb", "zbs", "zkt" and "zfhmin":
query-cpu-model-expansion type=full model={"name":"rv64"}
{"return": {"model":
{"name": "rv64", "props": {... "rva22u64": false, ...}}}}
query-cpu-model-expansion type=full model={"name":"rv64",
"props":{"zba":true,"zbb":true,"zbs":true,"zkt":true,"zfhmin":true}}
{"return": {"model":
{"name": "rv64", "props": {... "rva22u64": true, ...}}}}
We have no vendor CPUs that supports rva22u64 (veyron-v1 is the closest
- it is missing just 'zkt').
In short, aside from the 'max' CPU, we have no CPUs that supports
rva22u64 by default.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-18-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Enabling a profile and then disabling some of its mandatory extensions
is a valid use. It can be useful for debugging and testing. But the
common expected use of enabling a profile is to enable all its mandatory
extensions.
Add an user warning when mandatory extensions from an enabled profile
are disabled in the command line. We're also going to disable the
profile flag in this case since the profile must include all the
mandatory extensions. This flag can be exposed by QMP to indicate the
actual profile state after the CPU is realized.
After this patch, this will throw warnings:
-cpu rv64,rva22u64=true,zihintpause=false,zicbom=false,zicboz=false
qemu-system-riscv64: warning: Profile rva22u64 mandates disabled extension zihintpause
qemu-system-riscv64: warning: Profile rva22u64 mandates disabled extension zicbom
qemu-system-riscv64: warning: Profile rva22u64 mandates disabled extension zicboz
Note that the following will NOT throw warnings because the profile is
being enabled last, hence all its mandatory extensions will be enabled:
-cpu rv64,zihintpause=false,zicbom=false,zicboz=false,rva22u64=true
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-17-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RVG behaves like a profile: a single flag enables a set of bits. Right
now we're considering user choice when handling RVG and zicsr/zifencei
and ignoring user choice on MISA bits.
We'll add user warnings for profiles when the user disables its
mandatory extensions in the next patch. We'll do the same thing with RVG
now to keep consistency between RVG and profile handling.
First and foremost, create a new RVG only helper to avoid clogging
riscv_cpu_validate_set_extensions(). We do not want to annoy users with
RVG warnings like we did in the past (see 9b9741c38f), thus we'll only
warn if RVG was user set and the user disabled a RVG extension in the
command line.
For every RVG MISA bit (IMAFD), zicsr and zifencei, the logic then
becomes:
- if enabled, do nothing;
- if disabled and not user set, enable it;
- if disabled and user set, throw a warning that it's a RVG mandatory
extension.
This same logic will be used for profiles in the next patch.
Note that this is a behavior change, where we would error out if the
user disabled either zicsr or zifencei. As long as users are explicitly
disabling things in the command line we'll let them have a go at it, at
least in this step. We'll error out later in the validation if needed.
Other notable changes from the previous RVG code:
- use riscv_cpu_write_misa_bit() instead of manually updating both
env->misa_ext and env->misa_ext_mask;
- set zicsr and zifencei directly. We're already checking if they
were user set and priv version will never fail for these
extensions, making cpu_cfg_ext_auto_update() redundant.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-16-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previous patches added several g_hash_table_insert() patterns. Add two
helpers, one for each user hash, to make the code cleaner.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-15-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The profile support is handling multi-letter extensions only. Let's add
support for MISA bits as well.
We'll go through every known MISA bit. If the profile doesn't declare
the bit as mandatory, ignore it. Otherwise, set the bit in env->misa_ext
and env->misa_ext_mask.
Now that we're setting profile MISA bits, one can use the rv64i CPU to boot
Linux using the following options:
-cpu rv64i,rva22u64=true,rv39=true,s=true,zifencei=true
In the near future, when rva22s64 (where, 's', 'zifencei' and sv39 are
mandatory), is implemented, rv64i will be able to boot Linux loading
rva22s64 and no additional flags.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-14-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We have two instances of the setting/clearing a MISA bit from
env->misa_ext and env->misa_ext_mask pattern. And the next patch will
end up adding one more.
Create a helper to avoid code repetition.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231218125334.37184-13-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We already track user choice for multi-letter extensions because we
needed to honor user choice when enabling/disabling extensions during
realize(). We refrained from adding the same mechanism for MISA
extensions since we didn't need it.
Profile support requires tne need to check for user choice for MISA
extensions, so let's add the corresponding hash now. It works like the
existing multi-letter hash (multi_ext_user_opts) but tracking MISA bits
options in the cpu_set_misa_ext_cfg() callback.
Note that we can't re-use the same hash from multi-letter extensions
because that hash uses cpu->cfg offsets as keys, while for MISA
extensions we're using MISA bits as keys.
After adding the user hash in cpu_set_misa_ext_cfg(), setting default
values with object_property_set_bool() in add_misa_properties() will end
up marking the user choice hash with them. Set the default value
manually to avoid it.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231218125334.37184-12-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The TCG emulation implements all the extensions described in the
RVA22U64 profile, both mandatory and optional. The mandatory extensions
will be enabled via the profile flag. We'll leave the optional
extensions to be enabled by hand.
Given that this is the first profile we're implementing in TCG we'll
need some ground work first:
- all profiles declared in riscv_profiles[] will be exposed to users.
TCG is the main accelerator we're considering when adding profile
support in QEMU, so for now it's safe to assume that all profiles in
riscv_profiles[] will be relevant to TCG;
- we'll not support user profile settings for vendor CPUs. The flags
will still be exposed but users won't be able to change them;
- profile support, albeit available for all non-vendor CPUs, will be
based on top of the new 'rv64i' CPU. Setting a profile to 'true' means
enable all mandatory extensions of this profile, setting it to 'false'
will disable all mandatory profile extensions of the CPU, which will
obliterate preset defaults. This is not a problem for a bare CPU like
rv64i but it can allow for silly scenarios when using other CPUs. E.g.
an user can do "-cpu rv64,rva22u64=false" and have a bunch of default
rv64 extensions disabled. The recommended way of using profiles is the
rv64i CPU, but users are free to experiment.
For now we'll handle multi-letter extensions only. MISA extensions need
additional steps that we'll take care later. At this point we can boot a
Linux buildroot using rva22u64 using the following options:
-cpu rv64i,rva22u64=true,sv39=true,g=true,c=true,s=true
Note that being an usermode/application profile we still need to
explicitly set 's=true' to enable Supervisor mode to boot Linux.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-11-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
KVM does not have the means to support enabling the rva22u64 profile.
The main reasons are:
- we're missing support for some mandatory rva22u64 extensions in the
KVM module;
- we can't make promises about enabling a profile since it all depends
on host support in the end.
We'll revisit this decision in the future if needed. For now mark the
'rva22u64' profile as unavailable when running a KVM CPU:
$ qemu-system-riscv64 -machine virt,accel=kvm -cpu rv64,rva22u64=true
qemu-system-riscv64: can't apply global rv64-riscv-cpu.rva22u64=true:
'rva22u64' is not available with KVM
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231218125334.37184-10-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The rva22U64 profile, described in:
https://github.com/riscv/riscv-profiles/blob/main/profiles.adoc#rva22-profiles
Contains a set of CPU extensions aimed for 64-bit userspace
applications. Enabling this set to be enabled via a single user flag
makes it convenient to enable a predictable set of features for the CPU,
giving users more predicability when running/testing their workloads.
QEMU implements all possible extensions of this profile. All the so
called 'synthetic extensions' described in the profile that are cache
related are ignored/assumed enabled (Za64rs, Zic64b, Ziccif, Ziccrse,
Ziccamoa, Zicclsm) since we do not implement a cache model.
An abstraction called RISCVCPUProfile is created to store the profile.
'ext_offsets' contains mandatory extensions that QEMU supports. Same
thing with the 'misa_ext' mask. Optional extensions must be enabled
manually in the command line if desired.
The design here is to use the common target/riscv/cpu.c file to store
the profile declaration and export it to the accelerator files. Each
accelerator is then responsible to expose it (or not) to users and how
to enable the extensions.
Next patches will implement the profile for TCG and KVM.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20231218125334.37184-9-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Named features (zic64b the sole example at this moment) aren't expose to
users, thus we need another way to expose them.
Go through each named feature, get its boolean value, do the needed
conversions (bool to qbool, qbool to QObject) and add it to output dict.
Another adjustment is needed: named features are evaluated during
finalize(), so riscv_cpu_finalize_features() needs to be mandatory
regardless of whether we have an input dict or not. Otherwise zic64b
will always return 'false', which is incorrect: the default values of
cache blocksizes ([cbom/cbop/cboz]_blocksize) are set to 64, satisfying
the conditions for zic64b.
Here's an API usage example after this patch:
$ ./build/qemu-system-riscv64 -S -M virt -display none
-qmp tcp:localhost:1234,server,wait=off
$ ./scripts/qmp/qmp-shell localhost:1234
Welcome to the QMP low-level shell!
Connected to QEMU 8.1.50
(QEMU) query-cpu-model-expansion type=full model={"name":"rv64"}
{"return": {"model":
{"name": "rv64", "props": {... "zic64b": true, ...}}}}
zic64b is set to 'true', as expected, since all cache sizes are 64
bytes by default.
If we change one of the cache blocksizes, zic64b is returned as 'false':
(QEMU) query-cpu-model-expansion type=full model={"name":"rv64","props":{"cbom_blocksize":128}}
{"return": {"model":
{"name": "rv64", "props": {... "zic64b": false, ...}}}}
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-8-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
zic64b is defined in the RVA22U64 profile [1] as a named feature for
"Cache blocks must be 64 bytes in size, naturally aligned in the address
space". It's a fantasy name for 64 bytes cache blocks. The RVA22U64
profile mandates this feature, meaning that applications using this
profile expects 64 bytes cache blocks.
To make the upcoming RVA22U64 implementation complete, we'll zic64b as
a 'named feature', not a regular extension. This means that:
- it won't be exposed to users;
- it won't be written in riscv,isa.
This will be extended to other named extensions in the future, so we're
creating some common boilerplate for them as well.
zic64b is default to 'true' since we're already using 64 bytes blocks.
If any cache block size (cbo{m,p,z}_blocksize) is changed to something
different than 64, zic64b is set to 'false'.
Our profile implementation will then be able to check the current state
of zic64b and take the appropriate action (e.g. throw a warning).
[1] https://github.com/riscv/riscv-profiles/releases/download/v1.0/profiles.pdf
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-7-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
QEMU already implements zicbom (Cache Block Management Operations) and
zicboz (Cache Block Zero Operations). Commit 59cb29d6a5 ("target/riscv:
add Zicbop cbo.prefetch{i, r, m} placeholder") added placeholders for
what would be the instructions for zicbop (Cache Block Prefetch
Operations), which are now no-ops.
The RVA22U64 profile mandates zicbop, which means that applications that
run with this profile might expect zicbop to be present in the riscv,isa
DT and might behave badly if it's absent.
Adding zicbop as an extension will make our future RVA22U64
implementation more in line with what userspace expects and, if/when
cache block prefetch operations became relevant to QEMU, we already have
the extension flag to turn then on/off as needed.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We don't have any form of a 'bare bones' CPU. rv64, our default CPUs,
comes with a lot of defaults. This is fine for most regular uses but
it's not suitable when more control of what is actually loaded in the
CPU is required.
A bare-bones CPU would be annoying to deal with if not by profile
support, a way to load a multitude of extensions with a single flag.
Profile support is going to be implemented shortly, so let's add a CPU
for it.
The new 'rv64i' CPU will have only RVI loaded. It is inspired in the
profile specification that dictates, for RVA22U64 [1]:
"RVA22U64 Mandatory Base
RV64I is the mandatory base ISA for RVA22U64"
And so it seems that RV64I is the mandatory base ISA for all profiles
listed in [1], making it an ideal CPU to use with profile support.
rv64i is a CPU of type TYPE_RISCV_BARE_CPU. It has a mix of features
from pre-existent CPUs:
- it allows extensions to be enabled, like generic CPUs;
- it will not inherit extension defaults, like vendor CPUs.
This is the minimum extension set to boot OpenSBI and buildroot using
rv64i:
./build/qemu-system-riscv64 -nographic -M virt \
-cpu rv64i,sv39=true,g=true,c=true,s=true,u=true
Our minimal riscv,isa in this case will be:
# cat /proc/device-tree/cpus/cpu@0/riscv,isa
rv64imafdc_zicntr_zicsr_zifencei_zihpm_zca_zcd#
[1] https://github.com/riscv/riscv-profiles/blob/main/profiles.adoc
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We'll add a new bare CPU type that won't have any default priv_ver. This
means that the CPU will default to priv_ver = 0, i.e. 1.10.0.
At the same we'll allow these CPUs to enable extensions at will, but
then, if the extension has a priv_ver newer than 1.10, we'll end up
disabling it. Users will then need to manually set priv_ver to something
other than 1.10 to enable the extensions they want, which is not ideal.
Change the setter() of extensions to allow user enabled extensions to
bump the priv_ver of the CPU. This will make it convenient for users to
enable extensions for CPUs that doesn't set a default priv_ver.
This change does not affect any existing CPU: vendor CPUs does not allow
extensions to be enabled, and generic CPUs are already set to priv_ver
LATEST.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Our current logic in get/setters of MISA and multi-letter extensions
works because we have only 2 CPU types, generic and vendor, and by using
"!generic" we're implying that we're talking about vendor CPUs. When adding
a third CPU type this logic will break so let's handle it beforehand.
In set_misa_ext_cfg() and set_multi_ext_cfg(), check for "vendor" cpu instead
of "not generic". The "generic CPU" checks remaining are from
riscv_cpu_add_misa_properties() and cpu_add_multi_ext_prop() before
applying default values for the extensions.
This leaves us with:
- vendor CPUs will not allow extension enablement, all other CPUs will;
- generic CPUs will inherit default values for extensions, all others
won't.
And now we can add a new, third CPU type, that will allow extensions to
be enabled and will not inherit defaults, without changing the existing
logic.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231218125334.37184-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
