vender id/device id... in configuration space are read-only registers
which are commonly defined for all pci devices.
So move those initialization into common place.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* rth/axp-next: (26 commits)
target-alpha: Implement TLB flush primitives.
target-alpha: Use a fixed frequency for the RPCC in system mode.
target-alpha: Trap for unassigned and unaligned addresses.
target-alpha: Remap PIO space for 43-bit KSEG for EV6.
target-alpha: Implement cpu_alpha_handle_mmu_fault for system mode.
target-alpha: Implement more CALL_PAL values inline.
target-alpha: Disable interrupts properly.
target-alpha: All ISA checks to use TB->FLAGS.
target-alpha: Swap shadow registers moving to/from PALmode.
target-alpha: Implement do_interrupt for system mode.
target-alpha: Add IPRs to be used by the emulation PALcode.
target-alpha: Use kernel mmu_idx for pal_mode.
target-alpha: Add various symbolic constants.
target-alpha: Use do_restore_state for arithmetic exceptions.
target-alpha: Tidy up arithmetic exceptions.
target-alpha: Tidy exception constants.
target-alpha: Enable the alpha-softmmu target.
target-alpha: Rationalize internal processor registers.
target-alpha: Merge HW_REI and HW_RET implementations.
target-alpha: Cleanup MMU modes.
...
BM_STATUS_INT is automatically set during ide_set_irq(), there's no reason to
set it manually in addition.
There is even one case where the interrupt status bit was set, but no IRQ was
raised. This is when the PRD table was reached but there is more data to
transfer. The correct behaviour for this case is not to set BM_STATUS_INT.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a dummy legacy ISA device whose responsibility is to
deploy sgabios, an option rom for a serial graphics adapter.
The proposal is that this device is always-on when -nographics,
but can otherwise be enable in any setup when -device sga is used.
[v2: suggestions on qdev by Markus ]
[v3: cleanups and documentation, per list suggestions ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Switch no_user off and make it suppress the default VGA.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The simple backend only supports a maximum of 6 arguments. Split the
scsi_req_parsed event in two parts to cope with the limit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The multiboot info struct's 'boot_device' field has 'part1' set to 0x01, which
maps to the second primary partition. To specify the first primary partition,
'part1' should be set to 0x00, since partition numbers start from zero
according to the multiboot spec.
Signed-off-by: Arun Thomas <arun.thomas@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
After the Qdev'ification of the MPC8544DS board and PCI bus, the internal
PCI bus name changed from "pci" to "pci.0". Reflect this change in the
search for that bus.
This patch enables networking on e500 guests again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Current rpath inline function is heavily used in all system calls.
This function has a static buffer making it a non-thread safe function.
This patch introduces new thread-safe routine and makes use of it.
Signed-off-by: Venkateswararao Jujjuri "<jvrao@linux.vnet.ibm.com>
Commit 353ac78d49 moved the files
without fixing the include paths. It used a modified CFLAGS
to add hw to the include search path, but this breaks builds
where the user wants to set special CFLAGS. Long include paths
also increase compilation time.
Therefore this patch removes the special CFLAGS for virtio
and fixes the include statements by using relative include paths.
v2: Remove special CFLAGS.
v3: Update needed for latest QEMU.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
This patch move the 9p device registration into its own file
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
v9fs_complete_rename() mistakenly renames files with similar name
as we don't check if the matched name is really an offspring.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: Venkateswararao Jujjuri (JV) <jvrao@linux.vnet.ibm.com>
Thanks to Tobias Hoffmann <th55@gmx.de> for this patch.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
After NACKing a read operation, a raising SCL should not trigger a new
read from the slave. Introduce a new state which just waits for a stop
or start condition after NACK.
Signed-off-by: Marcus Comstedt <marcus@mc.pp.se>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
All you could ever achieve with it is break stuff, so removing it
should be safe.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
virtio-serial-bus needs to treat "virtconsole" devices specially. It
uses VirtIOSerialPort member is_console to recognize them. It gets
its value via property initialization. Cute hack, except it lets
users mess with it: "-device virtconsole,is_console=0" isn't plugged
into port 0 as it should.
Move the flag to VirtIOSerialPortInfo. Keep the property for backward
compatibility; its value has no effect.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
virtio_serial_init() allocates the VirtIOSerialBus dynamically, but
virtio_serial_exit() doesn't free it.
Fix by getting rid of the allocation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Instead of calling flush_queued_data when unthrottling, schedule
a bh. That way we can return immediately to the caller, and the
flush uses the same call path as a have_data for callbackee.
No migration change is required because bh are called from vm_stop.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The LUN field in the CDB is a historical relic. Ignore it as reserved,
which is what modern SCSI specifications actually say.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The sg driver currently has a hardcoded limit of commands it
can handle simultaneously. When this limit is reached the
driver will return -EDOM. So we need to capture this to
enable proper return values here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
scsi_req_parse() already provides for a data direction setting,
so we should be using it to check for correct direction.
And we should return the sense code 'INVALID FIELD IN CDB'
in these cases.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The get_sense callback copies existing sense information into
the provided buffer. This is required if sense information
should be transferred together with the command response.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
... and remove some SCSIDevice variables or fields that now become unused.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the common part of scsi-disk.c and scsi-generic.c to the SCSI layer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The SCSI spec has a quite detailed list of sense codes available.
It even mandates the use of specific ones for some failure cases.
The current implementation just has one type of generic error
which is actually a violation of the spec in certain cases.
This patch introduces various predefined sense codes to have the
sense code reporting more in line with the spec.
On top of Hannes's patch I fixed the reply to REQUEST SENSE commands
with DESC=0 and a small (<18) length.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This is for when the request must be dropped in the void,
but still memory should be freed. To this end, the devices
register a second callback in SCSIBusOps.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This covers the case of canceling a request's I/O and still
completing it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The code for canceling requests upon reset is already the same. Clean
it up and move it to scsi-bus.c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Currently the SCSIRequest structure is abstracted away and cannot accessed
directly from the driver. This requires the handler to do a lookup on
an abstract 'tag' which identifies the SCSIRequest structure.
With this patch the SCSIRequest structure is exposed to the driver. This
allows use to use it directly as an argument to the SCSIDeviceInfo
callback functions and remove the lookup.
A new callback function 'alloc_req' is introduced matching 'free
req'; unref'ing to free up resources after use is moved into the
scsi_command_complete callbacks.
This temporarily introduces a leak of requests that are cancelled,
when they are removed from the queue and not from the driver. This
is fixed later by introducing scsi_req_cancel. That patch in turn
depends on this one, because the argument to scsi_req_cancel is a
SCSIRequest.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
With the next patch, a device may hold SCSIRequest for an indefinite
time. Split a rather big patch, and protect against access errors,
by reference counting them.
There is some ugliness in scsi_send_command implementation due to
the need to unref the request when it fails. This will go away
with the next patches, which move the unref'ing to the devices.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
If a request is canceled after it has been completed, scsi_cancel_io
would pass a stale aiocb to bdrv_aio_cancel. Avoid this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
There are more operations than a SCSI bus can handle, besides completing
commands. One example, which this series will introduce, is cleaning up
after a request is cancelled.
More long term, a "SCSI bus" can represent the LUNs attached to a
target; in this case, while all commands will ultimately reach a logical
unit, it is the target who is in charge of answering REPORT LUNs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
This abstracts calling the command_complete callback, reducing churn
in the following patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
scsi-generic scsi_read_complete() should not -both- call the client
complete callback with SCSI_REASON_DATA -and- call
scsi_command_complete(). The former will cause the client to queue a
new read or write request, while the later will free the request data
structure, thus causing the new read or write request to use a
freed/stale structure when it completes.
This patch fixes the bug, fixing a crash with scsi-generic & RHEL5.5
installer.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This patch finally merges the EHCI host adapter aka USB 2.0 support.
Based on the ehci bits collected @ git://git.kiszka.org/qemu.git ehci
EHCI has a long out-of-tree history. Project was started by Mark
Burkley, with contributions by Niels de Vos. David S. Ahern continued
working on it. Kevin Wolf, Jan Kiszka and Vincent Palatin contributed
bugfixes.
/me (Gerd Hoffmann) picked it up where it left off, prepared the code
for merge, fixed a few bugs and added basic user docs.
Cc: David S. Ahern <daahern@cisco.com>
Cc: Jan Kiszka <jan.kiszka@web.de>
Cc: Kevin Wolf <mail@kevin-wolf.de>
Cc: Vincent Palatin <vincent.palatin_qemu@m4x.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Remove the cancel callback from the USBPacket struct, move it over
to USBDeviceInfo. Zap usb_defer_packet() which is obsolete now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a usb_handle_packet function, put it into use everywhere.
Right now it just calls dev->info->handle_packet(), that will
change in future patches though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_msd_copy_data() may cause a recursive call to
usb_msd_command_complete() which in turn may complete
the packet, setting s->packet to NULL in case it does.
Recheck s->packet before calling usb_packet_complete()
to fix the double call.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make the linux usb host passthrough code use the usb_generic_handle_packet()
function, rather then the curent DYI code. This removes 200 lines of almost
identical code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This allows using the generic usb_generic_handle_packet function from
device code which does ASYNC control requests (such as the linux host
pass through code).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
UHCI host controller status register indicates error and
an interrupt is triggered on BABBLE and STALL errors.
Signed-off-by: Jan Vesely <jano.vesely@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is used for some devices that have multiple interfaces that form a logic
device. An example is Video Class, which has a Control interface and a
Streaming interface. There can be additional interfaces on the same (physical)
devices (e.g. a microphone), and Interface Association Descriptor handles this
case.
Signed-off-by: Brad Hards <bradh@frogmouth.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Previously we relied on the .bNumInterfaces, but that won't always be
accurate after the introduction of grouped interfaces.
Signed-off-by: Brad Hards <bradh@frogmouth.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* 'ppc-next' of git://repo.or.cz/qemu/agraf:
Fix a bug in mtsr/mtsrin emulation on ppc64
pSeries: Clean up write-only variables
w32: Fix compilation and replace non-portable usage of ulong
The SDIO specification introduces new commands 52 and 53.
Handle as illegal command but do not complain on stderr,
as SDIO-aware OSes (including Linux) may legitimately use
these in their probing for presence of an SDIO card.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Remove a duplicate #include of sysbus.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
If pic_irq is greater than 7, the irq level is always 0 on 32bits.
Signed-off-by: TeLeMan <geleman@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
A few pieces of the pSeries emulation code have variables which are set
but never used, which causes warnings on gcc 4.6. This patch removes
these instances.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
the s390 memory detection has a 16bit field that specifies the amount of
increments. This patch adopts the memory size to always fit into that
scheme. This also fixes virtio detection for these guests, since the
descriptor page is located after the main memory.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The s390x virtio bus keeps management information on virtio after the top
of the guest's RAM. We need to be able to tell the guest the size of its
RAM (without virtio stuff), but also be able to trap when the guest accesses
RAM outside of its scope (including virtio stuff).
So we need a variable telling us the size of the virtio stuff, so we can
calculate the highest available RAM address from that.
While at it, also increase the maximum number of virtio pages, so we play
along well with more recent kernels that spawn a ridiculous number of virtio
console adapters.
Signed-off-by: Alexander Graf <agraf@suse.de>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch makes qemu ignore unplug requests from the guest for pci
devices which are tagged as non-hotpluggable. Trouble spot is the
piix4 chipset with the ISA bridge. Requests to unplug that one will
make it go away together with all ISA bus devices, which are not
prepared to be unplugged and thus don't cleanup, leaving active
qemu timers behind in free'ed memory.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. Unlike
DriveInfo, BlockDriverState should be about the host part only.
One of the remaining guest bits there is the "type hint". -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.
Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A "scsi-disk" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "scsi-hd" and "scsi-cd" to model disk vs. CD in
the guest part.
Keep scsi-disk for backward compatibility.
Don't copy scsi-disk property removable to scsi-cd. It's not used and
always zero(!) there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
cppcheck report:
hw/xen_disk.c:309: style:
Variable 'len' is assigned a value that is never used
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix regression of 667bb59: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The commit 667bb59d23
uses d->ahci.mem before it is initialized by
ahci_init(). Fix this by calling ahci_init() first thing
so that it's safe to use all fields in the ahci state struct.
Reported-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Tested-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* 'ppc-next' of git://repo.or.cz/qemu/agraf:
PPC: Qdev'ify e500 pci
PPC MPC7544DS: Use new TLB helper function
PPC: Implement e500 (FSL) MMU
PPC: Add another 64 bits to instruction feature mask
PPC: Add GS MSR definition
PPC: Make MPC8544DS emulation work w/o KVM
PPC: Make MPC8544DS obey -cpu switch
Fix off-by-one error in sizing pSeries hcall table
ppc64: Fix out-of-tree builds
kvm: ppc: warn user on PAGE_SIZE mismatch
kvm: ppc: detect old headers
monitor: add PPC BookE SPRs
kvm: ppc: fixes for KVM_SET_SREGS on init
ppc64: Don't try to build sPAPR RTAS on Darwin
Place pseries vty devices at addresses more similar to existing machines
Make pSeries 'model' property more closely resemble real hardware
pseries: Increase maximum CPUs to 256
The e500 PCI controller isn't qdev'ified yet. This leads to severe issues
when running with -drive.
To be able to use a virtio disk with an e500 VM, let's convert the PCI
controller over to qdev.
Reviewed-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have some nice helpers that can find us a TLB entry, let's
use that on the machine initialization code, so we don't need to know
about the internals of the TLB array.
Signed-off-by: Alexander Graf <agraf@suse.de>
The MPC8544DS board emulation was only used with KVM so far, so some
parts of the code didn't provide proper values for non-KVM execution.
This patch makes the machine work without KVM enabled. To actually use
this, you also need proper e500v2 MMU emulation.
Signed-off-by: Alexander Graf <agraf@suse.de>
The MPC8544DS board emulation code ignored the user defined -cpu switch.
This patch enables it to only provide a sane default, not force an e500v2
CPU inside.
Signed-off-by: Alexander Graf <agraf@suse.de>
The pSeries machine uses two tables to look up guest hcalls for emulation.
One of these is exactly one entry too small to hold all the hcalls it needs
to, leading to memory corruption.
This patch fixes the bug, and while we're at it, make both tables 'static'
since they're never used from other modules.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Read them via KVM_GET_SREGS in kvm_arch_get_registers(),
and display them in "info registers".
Also get CR and PID from the existing KVM_GET_REGS.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the qemu pseries machine numbers its virtual serial devices
from 0. However, existing pSeries machines running pHyp number them from
0x30000000.
In theory these indices are arbitrary, since everything necessary for the
kernel to find them is advertised in the device tree. However the debian
installer, at least, incorrectly looks for a device named vty@30... to
determine whether to use the hypervisor console.
Therefore this patch moves the numbers we use to match the existing pHyp
practice, in order to workaround broken userspace apps of this type.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, the qemu emulated pseries machine puts
"qemu,emulated-pSeries-LPAR" in the device tree's root level 'model'
property. Unfortunately this confuses some installers and ybin, which
expect this to start with "IBM" on pSeries machines. This patch addresses
this problem, making the property more closely resemble the pattern of
existing real hardware.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The original pSeries machine was limited to 32 CPUs, more or less
arbitrarily. Particularly when we get SMT KVM guests it will be
pretty easy to exceed this. Therefore, raise the max number of CPUs
in a pseries machine guest to 256.
Signed-off-by: Anton Blanchard <anton@au1.ibm.com>
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Prototype without "inline" keyword breaks the build with some gcc
versions. Noticed by Alexander Graf.
Fix this by removing the inline keywork everywhere. Some functions
can't be inlined anyway as the are referenced using function pointers.
Beside that gcc does a pretty good job on auto-inlining these days.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The 'sense' field in the HBA status structure is misnamed, as it
actually carries the SCSI status. Rename it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-trivial@nongnu.org
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
cppcheck report:
hw/ac97.c:1004: style:
Variable 'written' is assigned a value that is never used
hw/ac97.c:1072: style:
Variable 'written' is assigned a value that is never used
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The code changed here is an unused data type name (evt_flush_occurred).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Prevent a deadlock caused by leaving a map cache bucket locked by the
preceding qemu_get_ram_ptr() call.
Signed-off-By: John Baboval <john.baboval@virtualcomputer.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
On IA32 host or IA32 PAE host, at present, generally, we can't create
an HVM guest with more than 2G memory, because generally it's almost
impossible for Qemu to find a large enough and consecutive virtual
address space to map an HVM guest's whole physical address space.
The attached patch fixes this issue using dynamic mapping based on
little blocks of memory.
Each call to qemu_get_ram_ptr makes a call to qemu_map_cache with the
lock option, so mapcache will not unmap these ram_ptr.
Blocks that do not belong to the RAM, but usually to a device ROM or to
a framebuffer, are handled in a separate function. So the whole RAMBlock
can be map.
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Every set_irq call makes a Xen hypercall.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch introduces Xen specific call in piix_pci.
The specific part for Xen is in write_config, set_irq and get_pirq.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is because there is not synchronisation of the vcpu register
between Xen and QEMU, so vmport can't work properly.
This patch introduces no_vmport parameter to pc_basic_device_init.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Introduce the Xen FV (Fully Virtualized) machine to Qemu, some more Xen
specific call will be added in further patches.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch moves above_4g_mem_size and below_4g_mem_size calculation in
the caller of pc_memory_init (pc_init1). And the prototype of
pc_memory_init is changed because there is no need anymore to have
variable pointer and the ram_size parameter.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The xenpv machine use the common init function.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch updates the libxenctrl calls in Qemu to use the new interface,
otherwise Qemu wouldn't be able to build against new versions of the
library.
We check libxenctrl version in configure, from Xen 3.3.0 to Xen
unstable.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
And put braces for blocks with a single statement.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this new field, we can specified which accelerator use to run the
machine, if the accelerator is not already specified by either a
configuration file or the command line options.
Currently, the only use will be made in the xenfv machine.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The general control register is a byte register.
Add support for byte reads.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MDI control is a 32 bit register, but may be read or written using
8 or 16 bit access. Data is latched when the MSB is written.
Add support for byte/word read/write access.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pointer is a 32 bit register, but may be written using 8 or 16 bit writes.
Add support for byte/word writes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
port is a 32 bit register, but may be written using 8 or 16 bit writes.
Add support for byte/word writes.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Like other Intel devices, e100 (eepro100) uses little endian byte order.
This patch was tested with these combinations:
i386 host, i386 + mipsel guests (le-le)
mipsel host, i386 guest (le-le)
i386 host, mips + ppc guests (le-be)
mips host, i386 guest (be-le)
mips and mipsel hosts were emulated machines.
v2:
Use prefix for new functions. Add the same prefix to stl_le_phys.
Fix alignment of mem (needed for word/dword reads/writes).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU sends frames smaller than 60 bytes to ethernet nics.
Such frames are rejected by real NICs and their emulations.
To avoid this behaviour, other NIC emulations pad received
frames. This patch enables this workaround for eepro100, too.
All related code is marked with CONFIG_PAD_RECEIVED_FRAMES,
so we can drop this in case QEMU's networking code is
ever changed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cppcheck reports that 'packet' is unused.
It was only used to calculate the size of the preceding data.
Removing it saves a lot of stack space (local variable rx).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When DEBUG_EEPRO100 was enabled, unsupported writes were logged twice.
Now logging in eepro100_write1 and eepro100_write2 is similar to the
logging in eepro100_write4 (which already was correct).
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Initialize scsi_len with zero when starting a new request, so any
stuff leftover from the previous request is cleared out. This may
happen in case the data returned by the scsi command doesn't fit
into the buffer provided by the guest.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Windows allows control transfers to pass up to 4k of data, so raise our
control buffer size to 4k. For control out transfers the usb core code copies
the control request data to a buffer before calling the device's handle_control
callback. Add a check for overflowing the buffer before copying the data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We don't use qemu internals from spice server context any more.
Thus we don't also need to grab the iothread mutex from spice
server context. And we don't have to temporarely release the
lock to avoid deadlocks. Drop all the calls.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch moves the displaystate callback calls for setting the cursor
and the mouse pointer from spice server to qemu (iothread) context.
This allows us to simplify locking.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch moves the creation of spice screen updates from the spice
server context to qemu iothread context (display refresh timer to be
exact). This way we avoid accessing qemu internals (display surface)
from spice thread context which in turn allows us to simplify locking.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
After the re-org of the atapi code, it might not be intuitive for a
reader of the code to understand why we're inserting a 'media not
present' state between cd changes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds support for Milkymist's minimal Ethernet MAC v2. It
superseds minimac1.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Prevent timers from firing right after starting.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
After enabling the framebuffer, ensure that the console is resized.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
kvmclock presence can be signalled by two different flags. So for
device creation, we have to test for both.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The virtio serial specification requres that the values in the config
space are encoded in native endian of the guest.
The qemu virtio-serial code did not do conversion to the guest endian
format what caused problems when host and guest use different format.
This patch corrects the qemu side, correctly doing host-native <->
guest-native conversions when accessing the config space. This won't
break any setups that aren't already broken, and fixes the case
of different host and guest endianness.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
So far we set IRR for edge IRQs even if the pin is masked. If the guest
later on unmasks and switches the pin to level-triggered mode, irr will
remain set, causing an IRQ storm. The point is that setting IRR is not
correct in this case according to the spec, and avoiding this resolves
the issue.
Reported-and-tested-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The nwnames field in TWALK message is assumed to be >=0 and <= MAXWELEM
which is defined as macro P9_MAXWELEM (16) in virtio-9p.h as per 9p2000
RFC. Appropriate changes are required in V9fsWalkState and v9fs_walk.
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
This patch removes the addition of null char in symlink file
which is being appended to file in case of mapped security model.
Without this patch, the extra null char causes LTP testcase lstat03
to fail and hence this fix is required.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
LCREATE function packs address of iounit in the pdu, fix that to send
actual iounit itself.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Acked-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
If we don't have default acl, removexattr on default acl
should return 0
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Now that we start adding more files related to 9pfs
it make sense to move them to a separate directory
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Commit 5145b3d1cc revealed a bug in the lazy ROMD switch-back logic, but
resolved it by breaking that feature. This approach addresses the issue
by switching back to ROMD after a certain amount of read accesses
without further unlock sequences.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
* 'for-anthony' of git://repo.or.cz/qemu/kevin:
Remove obsolete 'enabled' variable from progress state
Add dd-style SIGUSR1 progress reporting
qed: Fix consistency check on 32-bit hosts
ide/atapi: Introduce CHECK_READY flag for commands
ide/atapi: Replace bdrv_get_geometry calls by s->nb_sectors
ide/atapi: Use table instead of switch for commands
ide/atapi: Factor commands out
ide: Split atapi.c out
Improve accuracy of block migration bandwidth calculation
atapi: Add 'medium ready' to 'medium not ready' transition on cd change
qemu-img: allow rebase to a NULL backing file when unsafe
Compilation for Windows needs a different declaration for the
printf format attribute, so use the macro which was defined for
this purpose.
Cc: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Some commands are supposed to report a Not Ready Condition (i.e. they require
a medium to be present in order to execute successfully). Instead of
duplicating the check in each command implementation, let's add a flag and
check it before calling the command.
This patch only converts existing checks, it does not introduce new checks for
any of the other commands that can/should report a Not Ready Condition.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The disk size can only change when the medium is changed, and the change
callback takes care of updating s->nb_sectors in this case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In preparation for a table of function pointers, factor each command out from
ide_atapi_cmd() into its own function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 Table F.1 lists errors that can be thrown for the TEST_UNIT_READY
command. Going from medium not ready to medium ready states is
communicated by throwing an error.
This adds the missing 'tray opened' event that we fail to report to
guests. After doing this, older Linux guests properly revalidate a disc
on the change command. HSM violation errors, which caused Linux guests
to do a soft-reset of the link, also go away:
ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
sr 1:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0
res 01/60:00:00:00:00/00:00:00:00:00/a0 Emask 0x3 (HSM violation)
ata2.00: status: { ERR }
ata2: soft resetting link
ata2.00: configured for MWDMA2
ata2: EH complete
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Trace events cannot use %s in their format strings because trace
backends vary in how they can deference pointers (if at all). Recording
const char * values is not meaningful if their contents are not recorded
too.
Change grlib trace events that rely on strings so that they communicate
similar information without using strings.
A follow-up patch explains this limitation and updates docs/tracing.txt.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
gcc can check the format string for correctness even when debugging output is
not enabled.
Have to make sure arguments are always available. They are optimized out if
unneeded.
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Removes double (( )) to make DEBUG_PRINT compatible with real function calls.
Change the name to DPRINTF to be consistent with other DPRINTF macros
throughout qemu.
Include the "RTL8139: " prefix in the macro. This changes some debug output
slightly since the prefix wasn't present on all lines.
Part of the change was done using the "coccinelle" tool with the following
small semantic match:
@@ expression E; @@
- DEBUG_PRINT((E))
+ DPRINTF(E)
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Prevents a compilation failure when DEBUG_RTL8139 is defined:
CC libhw32/rtl8139.o
cc1: warnings being treated as errors
hw/rtl8139.c: In function ‘rtl8139_cplus_transmit_one’:
hw/rtl8139.c:1960: error: format ‘%8lx’ expects type ‘long unsigned int’, but argument 5 has type ‘target_phys_addr_t’
make[1]: *** [rtl8139.o] Error 1
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It was a half conversion. Finish it.
enabled can only get values of 0, 1 or 2, was declared as an int but
sent as an unint8_t, change its type.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Newer kernels are large enough that they can overlap the address
where qemu places the initrd. Move the initrd up so that there is
enough space for the kernel again.
Unfortunately it's not possible to automatically determine the
size of the kernel if it is compressed, so this is the best we
can do.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add very basic implementation of collie PDA emulation. The system lacks
LoCoMo and graphics/sound emulation. Linux kernel boots up to mounting
rootfs (theoretically it can be provided in pflash images).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Basic implementation of DEC/Intel SA-1100/SA-1110 chips emulation.
Implemented:
- IRQs
- GPIO
- PPC
- RTC
- UARTs (no IrDA/etc.)
- OST reused from pxa25x
Everything else is TODO (esp. PM/idle/sleep!) - see the todo in the
hw/strongarm.c
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For emulation (and migration) we need to know about the guest's storage keys.
These are separate from actual RAM contents, so we need to allocate them in
parallel to RAM.
While touching the file, this patch also adjusts the hypercall function
to a new syntax that aligns better with tcg emulated code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The KVM interrupt injection path is non-generic for now. So we need to push
knowledge of how to inject a device interrupt using KVM into the actual device
code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We need to add some more logic to the CPU description to leverage emulation
of an s390x CPU. This patch adds all the required helpers, fields in CPUState
and constant definitions required for user and system emulation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If the memory size given on the command line is equal to the
maximum size of memory defined by the hardware, there is no
"empty slot" after physical memory.
The following command
qemu-system-sparc -m 256
raised an assertion:
exec.c:2614: cpu_register_physical_memory_offset: Assertion `size' failed
This can be fixed either at the caller side (don't call empty_slot_init)
or in empty_slot_init (do nothing) when size == 0. The second solution
was choosen here because it is more robust.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Implement the 'media' sub-command of the GET_EVENT_STATUS_NOTIFICATION
command. This helps us report tray open, tray closed, no media, media
present states to the guest.
Newer Linux kernels (2.6.38+) rely on this command to revalidate discs
after media change.
This patch also sends out tray open/closed status to the guest driver
when requested e.g. via the CDROM_DRIVE_STATUS ioctl (thanks Markus).
Without such notification, the guest and qemu's tray open/close status
was frequently out of sync, causing installers like Anaconda detecting
no disc instead of tray open, confusing them terribly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle GET_EVENT_STATUS_NOTIFICATION's No Event Available response in a
generic way so that future additions to the code to handle other
response types is easier.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of using magic numbers, use structs that are more descriptive of
the fields being used.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This makes the code more readable.
Also, there's a block like:
if () {
...
} else {
...
}
Split that into
if () {
...
return;
}
...
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After a media change, the only commands allowed from the guest were
REQUEST_SENSE and INQUIRY. The guest may also issue
GET_EVENT_STATUS_NOTIFICATION commands to get media
changed notification.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Table 629 of the MMC-5 spec mentions two different error conditions when
a CDROM eject is requested: a) while a disc is inserted and b) while a
disc is not inserted.
Ensure we return the appropriate error for the present condition of the
drive and disc status.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drivers are free to lock drives without any media present. Such a
condition should not result in an error condition.
See Table 341 in MMC-5 spec for details.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using cpu_physical_memory_read, cpu_physical_memory_write and ldub_phys
improves readability and allows removing some type casts.
lduw_phys and ldl_phys were not used because both require aligned
addresses. Therefore it is not possible to simply replace existing
calls by one of these functions.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Remove a write-only variable, spotted by GCC 4.6.0:
/src/qemu/hw/ppc.c: In function 'power7_set_irq':
/src/qemu/hw/ppc.c:255:9: error: variable 'cur_level' set but not used [-Werror=unused-but-set-variable]
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The feature bitmap in the s390 virtio machine is little endian. To
address for that, we need to bswap the values after reading them out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The proper way to signal that a sysbus devices need no MMIO region is to
pass -1 to sysbus_create_simple.
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out ACPI GPE logic. Later it will be used by ICH9 ACPI.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On Mon, 4 Apr 2011 20:15:30 +0200, Aurelien Jarno <aurelien@aurel32.net> wrote:
> Is it really safe ignoring write to this register? If yes, it's probably
> a good idea to explain why in a comment. In any case, if supporting this
> register is easy to do, it would be the best option.
I think it is safe. Please see an updated comment below.
And though implementing this register might be possible, I suppose it
is not worth to supporting FrameTooLong detection, for now at least.
Thank you for comments.
>8---------------------------------------------------------------------
From: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Date: Tue, 5 Apr 2011 23:12:07 +0900
Subject: [PATCH] lan9118: Ignore write to MAC_VLAN1 register
Since linux 2.6.38, smsc911x driver writes to VLAN1 registger.
Since this register only affects FrameTooLong detection, ignoring
write to this register should be safe.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out ACPI PM1_CNT logic. This will be used by ich9 acpi.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out ACPI PM1a EVT logic.
Later this will be used by ich9 acpi.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
factor out PM_TMR logic. Later This will be used by ich9 acpi.
Also fixes the same bug in vt82c686.c that was fixed by the following
commits.
> commit 055479feab
> Author: aliguori <aliguori@c046a42c-6fe2-441c-8c8c-71466251a162>
> Date: Wed Jan 21 16:31:20 2009 +0000
>
> Always return latest pmsts instead of the old one (Xiantao Zhang)
>
> It may lead to the issue when booting windows guests with acpi=1
> if return the old pmsts.
>
> Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
> Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Huacai Chen <zltjiangshi@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When checking pfl->rom_mode for when to lazily reenter ROMD mode,
the value was check was the opposite of what it should have been.
This prevent the part from returning to ROMD mode after a write
was made to the CFI rom region.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Quote filename in error message to spot possible whitespace character in
the filename and make error message more meaningful.
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
At present, the 'pseries' machine creates a flattened device tree in the
machine->init function to pass to either the guest kernel or to firmware.
However, the machine->init function runs before processing of -device
command line options, which means that the device tree so created will
be (incorrectly) missing devices specified that way.
Supplying a correct device tree is, in any case, part of the required
platform entry conditions. Therefore, this patch moves the creation and
loading of the device tree from machine->init to a reset callback. The
setup of entry point address and initial register state moves with it,
which leads to a slight cleanup.
This is not, alas, quite enough to make a fully working reset for pseries.
For that we would need to reload the firmware images, which on this
machine are loaded into RAM. It's a step in the right direction, though.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the pseries machine init code builds up an array, envs, of
CPUState pointers for all the cpus in the system. This is kind of
pointless, given the generic code already has a perfectly good linked list
of the cpus.
In addition, there are a number of places which assume that the cpu's
cpu_index field is equal to its index in this array. This is true in
practice, because cpu_index values are just assigned sequentially, but
it's conceptually incorrect and may not always be true.
Therefore, this patch abolishes the envs array, and explicitly uses the
generic cpu linked list and cpu_index values throughout.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
cppcheck reports this error:
hw/spapr_vscsi.c:274: error: Uninitialized variable: rc
If llen == 0, rc was indeed used without being initialized.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This will deadlock when the I/O thread is used, since the
CPU thread is blocked waiting for qemu_system_ready.
The synchronization is unnecessary since this is before
cpu_synchronize_all_post_init().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Like all block drivers virtio-blk should not allow small than block size
granularity access. But given that the protocol specifies a
byte unit length field we currently accept such requests, which cause
qemu to abort() in lower layers. Add checks to the main read and
write handlers to catch them early.
Reported-by: Conor Murphy <conor_murphy_virt@hotmail.com>
Tested-by: Conor Murphy <conor_murphy_virt@hotmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The specification for the virtio balloon device requres that the values
in the config space be encoded little-endian. This differs from most
virtio things, where guest-native endian is the norm.
Currently, the qemu virtio-balloon code correctly makes the conversion
on get_config(), but doesn't on set_config for the 'actual' field. The
kernel driver, on the other hand, correctly converts when setting the
actual field, but does not convert when reading the config space. The
upshot is that virtio-balloon will only work correctly if both host and
guest are LE, making all the conversions nops.
This patch corrects the qemu side, correctly doing host-native <-> LE
conversions when accessing the config space. This won't break any setups
that aren't already broken, and fixes the case of BE host, LE guest.
Fixing the BE guest case will require kernel fixes as well.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The 9p code already contains an attempt at the necessary endian
conversions, but it's broken.
The code which does conversion from host to guest does it correctly
and this code was copied to the function which does guest to host
conversion. However the copied code hasn't been correctly updated, so
it first endian converts some garbage on the stack and then overwrites
it with a field from incoming packet without conversion.
The patch fixes the mistakes.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Compiling with the DEBUG macro causes leaves hw/spapr_llan.c with an
unused variable, which is treated as an error in the qemu build.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
In previous life qdev_init_nofail() used to call hw_error() which
did register dump and other scary things. Now it calls
error_report() and does a regular exit(1). Fix the comment
to match reality.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
While looking at David Gibson's build-fix for hw/usb-ccid.c, I noticed a spello
in a comment on the following (unchanged) line.
Signed-off-by: Brad Hards <bradh@frogmouth.net>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
We need to keep DIR register unchanged across migration, but currently it
depends on the media_changed flags from block layer. Since we do not
save/restore it and the bdrv_open() called in dest node may set the
media_changed flag when trying to open floppy image, guest driver may think the
floppy have changed after migration. To fix this, a new filed media_changed in
FDrive strcutre was introduced in order to save and restore the it from block
layer through pre_save/post_load callbacks.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
factor out ide initialization to call drive_get(IF_IDE)
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Bug fix: routines 'ioreq_runio_qemu_sync' and 'ioreq_runio_qemu_aio'
won't call 'ioreq_unmap' or 'ioreq_finish' on errors, leaving ioreq in
the blkdev->inflight list and a leak.
Signed-off-by: Feiran Zheng <famcool@gmail.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is similar to pci_register_bar(), but automatically registers a single
memory region spanning the entire BAR.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cirrus VGA (at least) calls register memory region
with the same values again and again. The
registration in vhost-net slows this a lot,
optimize by checking that the same data is already registered.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
