Add support for generating the ISS (Instruction Specific Syndrome)
for Data Abort exceptions taken from AArch32. These syndromes are
used by hypervisors for example to trap and emulate memory accesses.
This is the equivalent for AArch32 guests of the work done for AArch64
guests in commit aaa1f954d4.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In the ARM ldr/str decode path, rather than directly testing
"insn & (1 << 21)" and "insn & (1 << 24)", abstract these
bits out into wbit and pbit local flags. (We will want to
do more tests against them to determine whether we need to
provide syndrome information.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In BE32 mode, sub-word size watchpoints can fail to trigger because the
address of the access is adjusted in the opcode helpers before being
compared with the watchpoint registers. This patch reverses the address
adjustment before performing the comparison with the help of a new CPUClass
hook.
This version of the patch augments and tidies up comments a little.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: caaf64ffc72f6ae183015337b7afdbd4b8989cb6.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Thumb-1 code has some issues in BE32 mode (as currently implemented). In
short, since bytes are swapped within words at load time for BE32
executables, this also swaps pairs of adjacent Thumb-1 instructions.
This patch un-swaps those pairs of instructions again, both for execution,
and for disassembly. (The previous version of the patch always read four
bytes in arm_read_memory_func and then extracted the proper two bytes,
in a probably misguided attempt to match the behaviour of actual hardware
as described by e.g. the ARM9TDMI TRM, section 3.3 "Endian effects for
instruction fetches". It's less complicated to just read the correct
two bytes though.)
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: ca20462a044848000370318a8bd41dd0a4ed273f.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new "cfgend" property which selects whether the CPU resets into
big-endian mode or not. This setting affects whether we reset with
SCTLR_B (ARMv6 and earlier) or SCTLR_EE (ARMv7 and later) set.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: 11420d1c49636c1790e60578ee996e51f0f0b835.1484929304.git.julian@codesourcery.com
[PMM: use error_report_err() rather than error_report();
move the integratorcp changes to their own patch;
drop an unnecessary extra #include;
rephrase commit message accordingly;
move setting of reset_sctlr above registration of cpregs
so it actually has an effect]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Macro calls without a trailing ; look weird in C, this works as a side
effect of how QEMU_BUILD_BUG_ON is implemented. Fix this up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
stub version of MISMATCH_CHECK is empty so it's easy to misuse for
people not building kvm on arm. Use QEMU_BUILD_BUG_ON similar to the
non-stub version to make it easier to catch bugs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
For M profile (unlike A profile) the reset value of R14 is specified
as 0xffffffff. (The rationale is that this is an illegal exception
return value, so if guest code tries to return to it it will result
in a helpful exception.)
Registers r0 to r12 and the flags are architecturally UNKNOWN on
reset, so we leave those at zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-11-git-send-email-peter.maydell@linaro.org
For M profile CPUs, FAULTMASK should be 0 on reset, like PRIMASK.
QEMU stores FAULTMASK in the PSTATE F bit, so (as with PRIMASK in the
I bit) we have to clear these to undo the A profile default of 1.
Update the comment accordingly and move it so that it's closer to the
code it's referring to.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-10-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message, moved comments]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For v7M attempts to access a nonexistent coprocessor are reported
differently from plain undefined instructions (as UsageFaults of type
NOCP rather than type UNDEFINSTR). Split them out into a new
EXCP_NOCP so we can report the FSR value correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-8-git-send-email-peter.maydell@linaro.org
When we take an exception for an undefined instruction, set the
appropriate CFSR bit.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-7-git-send-email-peter.maydell@linaro.org
[PMM: tweaked commit message, comment]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CCR.STACKALIGN bit controls whether the CPU is supposed to force
8-alignment of the stack pointer on entry to the exception handler.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Message-id: 1485285380-10565-6-git-send-email-peter.maydell@linaro.org
[PMM: commit message and comment tweaks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the structure fields, VMState fields, reset code and macros for
the v7M system control registers CCR, CFSR, HFSR, DFSR, MMFAR and
BFAR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-4-git-send-email-peter.maydell@linaro.org
We only use the IS_M() macro in two places, and it's a bit of a
namespace grab to put in cpu.h. Drop it in favour of just explicitly
calling arm_feature() in the places where it was used.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-2-git-send-email-peter.maydell@linaro.org
FAULTMASK must be cleared on return from all
exceptions other than NMI.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-7-git-send-email-peter.maydell@linaro.org
The v7m CONTROL register bit 1 is SPSEL, which indicates
the stack being used. We were storing this information
not in v7m.control but in the separate v7m.other_sp
structure field. Unfortunately, the code handling reads
of the CONTROL register didn't take account of this, and
so if SPSEL was updated by an exception entry or exit then
a subsequent guest read of CONTROL would get the wrong value.
Using a separate structure field doesn't really gain us
anything in efficiency, so drop this unnecessary complexity
in favour of simply storing all the bits in v7m.control.
This is a migration compatibility break for M profile
CPUs only.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-6-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message;
use deposit32(); use FIELD to define constants for
masking and shifting of CONTROL register fields
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Give an explicit error and abort when a load
from the vector table fails. Architecturally this
should HardFault (which will then immediately
fail to load the HardFault vector and go into Lockup).
Since we don't model Lockup, just report this guest
error via cpu_abort(). This is more helpful than the
previous behaviour of reading a zero, which is the
address of the reset stack pointer and not a sensible
location to jump to.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-4-git-send-email-peter.maydell@linaro.org
[PMM: expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For v7m we need to catch attempts to execute from special
addresses at 0xfffffff0 and above. Previously we did this
with the aid of a hacky special purpose lump of memory
in the address space and a check in translate.c for whether
we were translating code at those addresses.
We can implement this more cleanly using a CPU
unassigned access handler which throws the exception
if the unassigned access is for one of the special addresses.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-3-git-send-email-peter.maydell@linaro.org
[PMM:
* drop the deletion of the "don't interrupt if PC is magic"
code in arm_v7m_cpu_exec_interrupt() -- this is still
required
* don't generate an exception for unassigned accesses
which aren't to the magic address -- although doing
this is in theory correct in practice it will break
currently working guests which rely on the RAZ/WI
behaviour when they touch devices which we haven't
modelled.
* trigger EXCP_EXCEPTION_EXIT on is_exec, not !is_write
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MRS and MSR instruction handling has a number of flaws:
* unprivileged accesses should only be able to read
CONTROL and the xPSR subfields, and only write APSR
(others RAZ/WI)
* privileged access should not be able to write xPSR
subfields other than APSR
* accesses to unimplemented registers should log as
guest errors, not abort QEMU
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1484937883-1068-2-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Enable the ARM_FEATURE_EL2 bit on Cortex-A52 and
Cortex-A57, since this is all now sufficiently implemented
to work with the GICv3. We provide the usual CPU property
to disable it for backwards compatibility with the older
virt boards.
In this commit, we disable the EL2 feature on the
virt and ZynpMP boards, so there is no overall effect.
Another commit will expose a board-level property to
allow the user to enable EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-18-git-send-email-peter.maydell@linaro.org
The PSCI spec states that a CPU_ON call should cause the new
CPU to be started in the highest implemented Non-secure
exception level. We were incorrectly starting it at the
exception level of the caller, which happens to be correct
if EL2 is not implemented. Implement the correct logic
as described in the PSCI 1.0 spec section 6.4:
* if EL2 exists and SCR_EL3.HCE is set: start in EL2
* otherwise start in EL1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-17-git-send-email-peter.maydell@linaro.org
Add fields to the ARMCPU structure to allow CPU classes to
specify the configurable aspects of their GIC CPU interface.
In particular, the virtualization support allows different
values for number of list registers, priority bits and
preemption bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-6-git-send-email-peter.maydell@linaro.org
The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
The DBGVCR_EL2 system register is needed to run a 32-bit
EL1 guest under a Linux EL2 64-bit hypervisor. Its only
purpose is to provide AArch64 with access to the state of
the DBGVCR AArch32 register. Since we only have a dummy
DBGVCR, implement a corresponding dummy DBGVCR32_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To run a VM in 32-bit EL1 our AArch32 interrupt handling code
needs to be able to cope with VIRQ and VFIQ exceptions.
These behave like IRQ and FIQ except that we don't need to try
to route them to Monitor mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYeOOmAAoJEPvQ2wlanipE3ZUH/Rsfpl23kXCMmqoXEIhWXy+h
yf8ARWCmpU6UKfwb+sH4vLegBfU56f62vVkGQ6oaaAbuyQ4SxCUlZGMO/rqY8/TE
m57aM+VfEE+bIdinAtLjFM24EVp/exMfkeutK7ItzLv7GwlrBos0J5veyCuyJ15q
pccV24jrpbJGilEeJ2GblKp3r2I3dInQGauOQhtoP3MNjHmYNSQD7noSbdN/JiTR
9H2eV700pg3ZPaSfO+CTVQN+cHjK1FC6qLi6916YZY9llnSOnDAegBYgbwE1RIBw
AULpWrezYveKy71eFhHVtGxnPeCJ8J4GVECMK0P0cdxzprIXFh1kZezyM4bxAGk=
=sboI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1' into staging
This is the same as the v3 posted except a re-base and a few extra signoffs
# gpg: Signature made Fri 13 Jan 2017 14:26:46 GMT
# gpg: using RSA key 0xFBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>"
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1:
cputlb: drop flush_global flag from tlb_flush
cpu_common_reset: wrap TCG specific code in tcg_enabled()
qom/cpu: move tlb_flush to cpu_common_reset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have never has the concept of global TLB entries which would avoid
the flush so we never actually use this flag. Drop it and make clear
that tlb_flush is the sledge-hammer it has always been.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
[DG: ppc portions]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
It is a common thing amongst the various cpu reset functions want to
flush the SoftMMU's TLB entries. This is done either by calling
tlb_flush directly or by way of a general memset of the CPU
structure (sometimes both).
This moves the tlb_flush call to the common reset function and
additionally ensures it is only done for the CONFIG_SOFTMMU case and
when tcg is enabled.
In some target cases we add an empty end_of_reset_fields structure to the
target vCPU structure so have a clear end point for any memset which
is resetting value in the structure before CPU_COMMON (where the TLB
structures are).
While this is a nice clean-up in general it is also a precursor for
changes coming to cputlb for MTTCG where the clearing of entries
can't be done arbitrarily across vCPUs. Currently the cpu_reset
function is usually called from the context of another vCPU as the
architectural power up sequence is run. By using the cputlb API
functions we can ensure the right behaviour in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
The new typename attribute on query-cpu-definitions will be used
to help management software use device-list-properties to check
which properties can be set using -cpu or -global for the CPU
model.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1479320499-29818-1-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ARM1176 CPUs have TrustZone support and can use the Vector Base
Address Register, but currently, qemu only adds VBAR support to ARMv7
CPUs. Fix this by adding a new feature ARM_FEATURE_VBAR which can used
for ARMv7 and ARM1176 CPUs.
The VBAR feature is always set for ARMv7 because some legacy boards
require it even if this is not architecturally correct.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1481810970-9692-1-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already log exception entry; add logging of the AArch64 exception
return path as well.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
We add s->be_data within do_vec_ld/st. Adding it here means that
we have the wrong bits set in SIZE for a big-endian host, leading
to g_assert_not_reached in write_vec_element and read_vec_element.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1481085020-2614-3-git-send-email-rth@twiddle.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since CPUARMState.vfp.regs is not 16 byte aligned, the ^ 8 fixup used
for a big-endian host doesn't do what's intended. Fix this by adding
in the vfp.regs offset after computing the inter-register offset.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1481085020-2614-2-git-send-email-rth@twiddle.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The value of the MVFR1 (Media and VFP Feature Register 1) register for
the Cortex-A8 appears to be incorrect (according to the TRM, DDI0344K),
with the "full denormal arithmetic" and "propagation of NaN" fields
holding both 0 instead of both 1.
I had a go tracing the history of the use of this value, and it seems
it's always just been wrong in QEMU: maybe it was derived from early
documentation, or guessed based on the use of a "VFP Lite" implementation
in the Cortex-A8.
Depending on the startup/early-boot code in use, this can manifest as
failure to perform denormal arithmetic properly: in our case, selecting
a Cortex-A8 CPU when using QEMU as an instruction-set simulator for
bare-metal GCC testing caused tests using denormal arithmetic to
fail. Problems might be masked (or not occur) when using a full OS kernel
with suitable trap handlers (I'm not sure).
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: 1481130858-31767-1-git-send-email-julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
