RISC-V should also generate the SPCR in a manner similar to ARM.
Therefore, instead of replicating the code, relocate this function
to the common AML build.
Signed-off-by: Sia Jee Heng <jeeheng.sia@starfivetech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240129021440.17640-2-jeeheng.sia@starfivetech.com>
[ Changes by AF:
- Add missing Language SPCR entry
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The sun4v RTC device model added under commit a0e893039c in 2016
was unfortunately added with a license of GPL-v3-or-later, which is
not compatible with other QEMU code which has a GPL-v2-only license.
Relicense the code in the .c and the .h file to GPL-v2-or-later,
to make it compatible with the rest of QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini (for Red Hat) <pbonzini@redhat.com>
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240223161300.938542-1-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain
Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we can generate reliable clock frequencies from the RCC, remove
the hacky definition of the sysclk in the b_l475e_iot01a initialisation
code and use the correct RCC clock.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-8-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add write protections for the fields in the CR register.
PLL configuration write protections (among others) have not
been handled yet. This is planned in a future patch set.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-7-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Update the RCC state and propagate frequency changes when writing to the
RCC registers. Currently, ICSCR, CIER, the reset registers and the stop
mode registers are not implemented.
Some fields have not been implemented due to uncertainty about
how to handle them (Like the clock security system or bypassing
mecanisms).
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-6-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate the whole clock tree and using the Clock multiplexers and
the PLLs defined in the previous commits. This allows to statically
define the clock tree and easily follow the clock signal from one end to
another.
Also handle three-phase reset now that we have defined a known base
state for every object.
(Reset handling based on hw/misc/zynq_sclr.c)
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-5-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This object represents the PLLs and their channels. The PLLs allow for a
more fine-grained control of the clocks frequency.
The migration handling is based on hw/misc/zynq_sclr.c.
Three phase reset will be handled in a later commit.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Message-id: 20240303140643.81957-4-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This object is used to represent every multiplexer in the clock tree as
well as every clock output, every presecaler, frequency multiplier, etc.
This allows to use a generic approach for every component of the clock tree
(except the PLLs).
The migration handling is based on hw/misc/zynq_sclr.c.
Three phase reset will be handled in a later commit.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240303140643.81957-3-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary files to add a simple RCC implementation with just
reads from and writes to registers. Also instantiate the RCC in the
STM32L4x5_SoC. It is needed for accurate emulation of all the SoC
clocks and timers.
Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240303140643.81957-2-arnaud.minier@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds loopback for sent characters, sent BREAK,
and modem-control signals.
Loopback of send and modem-control is often used for uart
self tests in real hardware but missing from current pl011
model, resulting in self-test failures when running in QEMU.
This implementation matches what is observed in real pl011
hardware placed in loopback mode:
1. Input characters and BREAK events from serial backend
are ignored, but
2. Both TX characters and BREAK events are still sent to
serial backend, in addition to be looped back to RX.
Signed-off-by: Tong Ho <tong.ho@amd.com>
Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20240227054855.44204-1-tong.ho@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
BCM2835 has three I2C controllers. All of them share the same interrupt line.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240224191038.2409945-3-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few deficiencies in the current device model need to be noted.
1. FIFOs are not used. All sends and receives are done directly.
2. Repeated starts are not emulated. Repeated starts can be triggered in real
hardware by sending a new read transfer request in the window time between
transfer active set of write transfer request and done bit set of the same.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240224191038.2409945-2-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix GIC settings when using --without-default-devices
* Fix USB PCAP streams on Windows
* Remove temporary files from test-util-sockets
* Fix TLS io channels sending too much data to the backend
-----BEGIN PGP SIGNATURE-----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=9JAI
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-03-01' of https://gitlab.com/thuth/qemu into staging
* Fix some bugs in the vring setup of libqos
* Fix GIC settings when using --without-default-devices
* Fix USB PCAP streams on Windows
* Remove temporary files from test-util-sockets
* Fix TLS io channels sending too much data to the backend
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmXhjBcRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWzZw/+OTSsKg6JTX0z3fjL6If+Ns/EnFiniHHI
# y1jR7fPub3ybFokgHIWrRVG+9ol+1tJuPlO5Bsx1SKFzNC8++l1iyK7E25xnmp2P
# Ry/Z0ZSWp3JWCtLm6km5pKl3wWI9p0XwfUOJbCWYM5dOsd2a4C4DSvjcwNXR7pTB
# 4AxXFj5G5UwXuffgPnBzeerm5baNweSqa/uczUY6Od+iJwmHpaSk0SJ4NIlIYvnS
# z3BH81trQAoKYZyywp0aF+jH9w3YNwD1XDp2Bcf3qSWDdokN55V13yyiSllTfUwX
# Lq3fotoLqFJL0A4m8a3TdCKMP8ReoJATSriPHJmGMgqWGTnvtRBIsx1pmMpYRB6U
# EltaKW0WXeQAad0ZYGl4odx7kQUQjdc8HTQRTevQD9g3XpZZN0o9MfTPdM2eR5h6
# xaS8UEc61YJAcmD27Ir92JGGGMLBTYz4OGLx3Rj7l7S759GQ67qih9TGcE9nqSj+
# +wAHfiOjUZnSWnp7Hq4M/TIjNh0BuyBW4oRBASaikjjQ82Hih5bPTdRu1J8lYuXC
# PhN8dLwdk0NMrnnHuFDKq/sXjDeXF3Hg0AmtVvOGiB2z2OeVSPtMxl/YgniGVTbj
# CHXDqDrBAa7i6WxAo+TtUgE20iVz5uYzGqHmxTNpq6FzIRb1uvHksbjFlin79Pkw
# eF0Dj80zxAY=
# =9JAI
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Mar 2024 08:04:39 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-03-01' of https://gitlab.com/thuth/qemu:
chardev/char-socket: Fix TLS io channels sending too much data to the backend
tests/unit/test-util-sockets: Remove temporary file after test
hw/usb/bus.c: PCAP adding 0xA in Windows version
hw/intc/Kconfig: Fix GIC settings when using "--without-default-devices"
libqos/virtio.c: fix 'avail_event' offset in qvring_init()
libqos/virtio.c: init all elems in qvring_indirect_desc_setup()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
V2: fix build error on mipsel
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZeBrwAAKCRBAov/yOSY+
33YXA/4+A5Bpe/3+mSAWZSUlluGTqUi0ILBYRMyX1RXovMx4uCRGr7PXzAf03yKS
MZzlVzTuOK69WmTm/iTdYWOxkXisC3gzxL/wm8hP4lzh4c0dHrHRsKHqq6gR3+t2
ojdZn7TefeflnNqIhxXxgxb1OETofhBNnBJ74pvqxO7XV5SWnA==
=J2Kb
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20240229' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20240229
V2: fix build error on mipsel
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZeBrwAAKCRBAov/yOSY+
# 33YXA/4+A5Bpe/3+mSAWZSUlluGTqUi0ILBYRMyX1RXovMx4uCRGr7PXzAf03yKS
# MZzlVzTuOK69WmTm/iTdYWOxkXisC3gzxL/wm8hP4lzh4c0dHrHRsKHqq6gR3+t2
# ojdZn7TefeflnNqIhxXxgxb1OETofhBNnBJ74pvqxO7XV5SWnA==
# =J2Kb
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 29 Feb 2024 11:34:24 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240229' of https://gitlab.com/gaosong/qemu:
loongarch: Change the UEFI loading mode to loongarch
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since Windows text files use CRLFs for all \n, the Windows version of QEMU
inserts a CR in the PCAP stream when a LF is encountered when using USB PCAP
files. This is due to the fact that the PCAP file is opened as TEXT instead
of BINARY.
To show an example, when using a very common protocol to USB disks, the BBB
protocol uses a 10-byte command packet. For example, the READ_CAPACITY(10)
command will have a command block length of 10 (0xA). When this 10-byte
command (part of the 31-byte CBW) is placed into the PCAP file, the Windows
file manager inserts a 0xD before the 0xA, turning the 31-byte CBW into a
32-byte CBW.
Actual CBW:
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0a 25 USBC...........%
0050 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...............
PCAP CBW
0040 55 53 42 43 01 00 00 00 08 00 00 00 80 00 0d 0a USBC............
0050 25 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 %..............
I believe simply opening the PCAP file as BINARY instead of TEXT will fix
this issue.
Resolves: https://bugs.launchpad.net/qemu/+bug/2054889
Signed-off-by: Benjamin David Lunt <benlunt@fysnet.net>
Message-ID: <000101da6823$ce1bbf80$6a533e80$@fysnet.net>
[thuth: Break long line to avoid checkpatch.pl error]
Signed-off-by: Thomas Huth <thuth@redhat.com>
When using "--without-default-devices", the ARM_GICV3_TCG and ARM_GIC_KVM
settings currently get disabled, though the arm virt machine is only of
very limited use in that case. This also causes the migration-test to
fail in such builds. Let's make sure that we always keep the GIC switches
enabled in the --without-default-devices builds, too.
Message-ID: <20240221110059.152665-1-thuth@redhat.com>
Tested-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This removes a hidden use of qemu_host_page_size, hoisting
two uses of qemu_real_host_page_size to a local variable.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Helge Deller <deller@gmx.de>
The UEFI loading mode in loongarch is very different
from that in other architectures:loongarch's UEFI code
is in rom, while other architectures' UEFI code is in flash.
loongarch UEFI can be loaded as follows:
-machine virt,pflash=pflash0-format
-bios ./QEMU_EFI.fd
Other architectures load UEFI using the following methods:
-machine virt,pflash0=pflash0-format,pflash1=pflash1-format
loongarch's UEFI loading method makes qemu and libvirt incompatible
when using NVRAM, and the cost of loongarch's current loading method
far outweighs the benefits, so we decided to use the same UEFI loading
scheme as other architectures.
Cc: Andrea Bolognani <abologna@redhat.com>
Cc: maobibo@loongson.cn
Cc: Philippe Mathieu-Daudé <philmd@linaro.org>
Cc: Song Gao <gaosong@loongson.cn>
Cc: zhaotianrui@loongson.cn
Signed-off-by: Xianglai Li <lixianglai@loongson.cn>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <0bd892aa9b88e0f4cc904cb70efd0251fc1cde29.1708336919.git.lixianglai@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
- Fabiano's fixed-ram patches (1-5 only)
- Peter's cleanups on multifd tls IOC referencing
- Steve's cpr patches for vfio (migration patches only)
- Fabiano's fix on mbps stats racing with COMPLETE state
- Fabiano's fix on return path thread hang
-----BEGIN PGP SIGNATURE-----
iIcEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZd7AbhIccGV0ZXJ4QHJl
ZGhhdC5jb20ACgkQO1/MzfOr1wbg0gDyA3Vg3pIqCJ+u+hLZ+QKxY/pnu8Y5kF+E
HK2IdslQUQD+OX4ATUnl+CGMiVX9fjs1fKx0Z0Qetq8gC1YJF13yuA0=
=P2QF
-----END PGP SIGNATURE-----
Merge tag 'migration-next-pull-request' of https://gitlab.com/peterx/qemu into staging
Migration pull request
- Fabiano's fixed-ram patches (1-5 only)
- Peter's cleanups on multifd tls IOC referencing
- Steve's cpr patches for vfio (migration patches only)
- Fabiano's fix on mbps stats racing with COMPLETE state
- Fabiano's fix on return path thread hang
# -----BEGIN PGP SIGNATURE-----
#
# iIcEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZd7AbhIccGV0ZXJ4QHJl
# ZGhhdC5jb20ACgkQO1/MzfOr1wbg0gDyA3Vg3pIqCJ+u+hLZ+QKxY/pnu8Y5kF+E
# HK2IdslQUQD+OX4ATUnl+CGMiVX9fjs1fKx0Z0Qetq8gC1YJF13yuA0=
# =P2QF
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 28 Feb 2024 05:11:10 GMT
# gpg: using EDDSA key B9184DC20CC457DACF7DD1A93B5FCCCDF3ABD706
# gpg: issuer "peterx@redhat.com"
# gpg: Good signature from "Peter Xu <xzpeter@gmail.com>" [marginal]
# gpg: aka "Peter Xu <peterx@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: B918 4DC2 0CC4 57DA CF7D D1A9 3B5F CCCD F3AB D706
* tag 'migration-next-pull-request' of https://gitlab.com/peterx/qemu: (25 commits)
migration: Use migrate_has_error() in close_return_path_on_source()
migration: Join the return path thread before releasing to_dst_file
migration: Fix qmp_query_migrate mbps value
migration: options incompatible with cpr
migration: update cpr-reboot description
migration: stop vm for cpr
migration: notifier error checking
migration: refactor migrate_fd_connect failures
migration: per-mode notifiers
migration: MigrationNotifyFunc
migration: remove postcopy_after_devices
migration: MigrationEvent for notifiers
migration: convert to NotifierWithReturn
migration: remove error from notifier data
notify: pass error to notifier with return
migration/multifd: Drop unnecessary helper to destroy IOC
migration/multifd: Cleanup outgoing_args in state destroy
migration/multifd: Make multifd_channel_connect() return void
migration/multifd: Drop registered_yank
migration/multifd: Cleanup TLS iochannel referencing
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we expand the per-vCPU data for plugins we don't want to pollute
CPUState. For now this just moves the plugin_mask (renamed to
event_mask) as the memory callbacks are accessed directly by TCG
generated code.
Reviewed-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-23-alex.bennee@linaro.org>
This ensures we run during a cpu_exec, which allows to call start/end
exclusive from this init hook (needed for new scoreboard API introduced
later).
async work is run before any tb is translated/executed, so we can
guarantee plugin init will be called before any other hook.
The previous change made sure that any idle/resume cb call will not be
done before initializing plugin for a given vcpu.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Message-Id: <20240213094009.150349-5-pierrick.bouvier@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-20-alex.bennee@linaro.org>
Now we know all instances of GDBFeature that is used in CPU so we can
traverse them to find XML. This removes the need for a CPU-specific
lookup function for dynamic XMLs.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231213-gdb-v17-7-777047380591@daynix.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240227144335.1196131-12-alex.bennee@linaro.org>
Define MigrationNotifyFunc to improve type safety and simplify migration
notifiers.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1708622920-68779-7-git-send-email-steven.sistare@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Passing MigrationState to notifiers is unsound because they could access
unstable migration state internals or even modify the state. Instead, pass
the minimal info needed in a new MigrationEvent struct, which could be
extended in the future if needed.
Suggested-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1708622920-68779-5-git-send-email-steven.sistare@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Change all migration notifiers to type NotifierWithReturn, so notifiers
can return an error status in a future patch. For now, pass NULL for the
notifier error parameter, and do not check the return value.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1708622920-68779-4-git-send-email-steven.sistare@oracle.com
[peterx: dropped unexpected update to roms/seabios-hppa]
Signed-off-by: Peter Xu <peterx@redhat.com>
Remove the error object from opaque data passed to notifiers.
Use the new error parameter passed to the notifier instead.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1708622920-68779-3-git-send-email-steven.sistare@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Pass an error object as the third parameter to "notifier with return"
notifiers, so clients no longer need to bundle an error object in the
opaque data. The new parameter is used in a later patch.
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/1708622920-68779-2-git-send-email-steven.sistare@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
All calls to ide_init_drive comes from ide_dev_initfn. Just pass down the
IDEDevice (IDEState is kinda obsolete and should be merged into IDEDevice).
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a fd-bootchk property to PC machine types, so that -no-fd-bootchk
returns an error if the machine does not support booting from floppies
and checking for boot signatures therein.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Add support for UART0, in preparation of AST2700 models
-----BEGIN PGP SIGNATURE-----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=gFeX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20240227' of https://github.com/legoater/qemu into staging
aspeed queue:
* Add support for UART0, in preparation of AST2700 models
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmXd2nMACgkQUaNDx8/7
# 7KErPBAAjKRmJQF9aMEgf7uqsPnJojAVumFe63NE9Gqnvy4MzgoZWfdSnLl2Ddba
# im5IfR7MYv0tzJtqCVtz7o4JwXhhDwesWALQZBM/ms48aacPSNP+7Gn141yLuCCS
# Vr8NBSIz156lSsnFGnRUArcQTDKjDp/1TLRiGcS8SDm/S4Nn++nur+T054EZgbKR
# CMWDeavgzZRb9HPepvWDwqb9qs11hq5/onCqC886dVNznxEKAVYcd0FVbSn3OfDF
# 2EPvKh+fxHlW37wcctlGPnbJK5rRvFi78yZf5utSt+mlVhyiEXjQJ6p8zBIh2w5A
# NlsmUo/UYv1F41yC/vCFRR8KJ2wO5VW7zL6UCGMV6I9hxhu/Qw+FYqWdBbAZWsOO
# GFOkFbe8zbJFXTr/W7P5upBlA7U1/B9VbRj71eu01dqT+n8OGsk8yfnWVs1SjpoD
# 89ZIhpb7lSolQmjPPxrVyfUe3/8ncTx64+CZuAZjxPh/9HA8wDXwVRPtAbIvvGaZ
# YPQ4Qmd4m6nAANAvTg2ufj19WT64XKwrQ6O3IkmGcn0BzHl08GFjru8IUp6rbduG
# m6WqulL1Ej1PrYaiw5ktpJ4Fkoy6iEFXJOWfl3oTLp2KWE5VAohyRKI00AFnHiAC
# frK+cxT4bqDtJR8QbNyJy5d3ZGZV1R6ZA0XjQ1jtb8ty2qISysw=
# =gFeX
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 27 Feb 2024 12:49:55 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20240227' of https://github.com/legoater/qemu:
aspeed: fix hardcode boot address 0
aspeed: introduce a new UART0 device name
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Our model of the bcm2835 mailbox is missing a few properties
that we need for the raspi4 kernel:
* RPI_FWREQ_GET_CLOCKS
* RPI_FWREQ_GET_THROTTLED
* RPI_FWREQ_VCHIQ_INIT
Add minimal implementations of them.
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Message-id: 20240226000259.2752893-40-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: improved commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds RPi4B device tree modifications:
- disable pcie, rng200, thermal sensor and genet devices
(they're going to be re-enabled in the following commits)
- create additional memory region in device tree
if RAM amount exceeds VC base address.
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-12-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-11-sergey.kambalin@auriga.com
[PMM: Change name to 'raspi4b', not 'raspi4b-2g']
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pre-setup for raspberry pi 4 introduction
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-4-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pre setup for BCM2838 introduction
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240226000259.2752893-2-sergey.kambalin@auriga.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the reset of the sysbus (and thus all devices and buses anywhere
on the qbus tree) from qemu_register_reset() to qemu_register_resettable().
This is a behaviour change: because qemu_register_resettable() is
aware of three-phase reset, this now means that:
* 'enter' phase reset methods of devices and buses are called
before any legacy reset callbacks registered with qemu_register_reset()
* 'exit' phase reset methods of devices and buses are called
after any legacy qemu_register_reset() callbacks
Put another way, a qemu_register_reset() callback is now correctly
ordered in the 'hold' phase along with any other 'hold' phase methods.
The motivation for doing this is that we will now be able to resolve
some reset-ordering issues using the three-phase mechanism, because
the 'exit' phase is always after the 'hold' phase, even when the
'hold' phase function was registered with qemu_register_reset().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240220160622.114437-10-peter.maydell@linaro.org
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reimplement qemu_register_reset() via qemu_register_resettable().
We define a new LegacyReset object which implements Resettable and
defines its reset hold phase method to call a QEMUResetHandler
function. When qemu_register_reset() is called, we create a new
LegacyReset object and add it to the simulation_reset
ResettableContainer. When qemu_unregister_reset() is called, we find
the LegacyReset object in the container and remove it.
This implementation of qemu_unregister_reset() means we'll end up
scanning the ResetContainer's list of child objects twice, once
to find the LegacyReset object, and once in g_ptr_array_remove().
In theory we could avoid this by having the ResettableContainer
interface include a resettable_container_remove_with_equal_func()
that took a callback method so that we could use
g_ptr_array_find_with_equal_func() and g_ptr_array_remove_index().
But we don't expect qemu_unregister_reset() to be called frequently
or in hot paths, and we expect the simulation_reset container to
usually not have many children.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240220160622.114437-9-peter.maydell@linaro.org
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Implement new functions qemu_register_resettable() and
qemu_unregister_resettable(). These are intended to be
three-phase-reset aware equivalents of the old qemu_register_reset()
and qemu_unregister_reset(). Instead of passing in a function
pointer and opaque, you register any QOM object that implements the
Resettable interface.
The implementation is simple: we have a single global instance of a
ResettableContainer, which we reset in qemu_devices_reset(), and
the Resettable objects passed to qemu_register_resettable() are
added to it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240220160622.114437-8-peter.maydell@linaro.org
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Implement a ResetContainer. This is a subclass of Object, and it
implements the Resettable interface. The container holds a list of
arbitrary other objects which implement Resettable, and when the
container is reset, all the objects it contains are also reset.
This will allow us to have a 3-phase-reset equivalent of the old
qemu_register_reset() API: we will have a single "simulation reset"
top level ResetContainer, and objects in it are the equivalent of the
old QEMUResetHandler functions.
The qemu_register_reset() API manages its list of callbacks using a
QTAILQ, but here we use a GPtrArray for our list of Resettable
children: we expect the "remove" operation (which will need to do an
iteration through the list) to be fairly uncommon, and we get simpler
code with fewer memory allocations.
Since there is currently no listed owner in MAINTAINERS for the
existing reset-related source files, create a new section for
them, and add these new files there also.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20240220160622.114437-7-peter.maydell@linaro.org
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
This property allows users to change flash model on command line as
below.
ex: "-M xlnx-versal-virt,ospi-flash=mt35xu02gbba"
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Message-id: 20240220091721.82954-3-sai.pavan.boddu@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add Micro 2Gb OSPI flash part with sfdp data.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20240220091721.82954-2-sai.pavan.boddu@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The PL031 allows you to read RTCLR, which is meant to give you the last
value written. PL031State has an lr field which is used when reading
from RTCLR, and is present in the VM migration state, but we never
actually update it, so it always reads as its initial 0 value.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240222000341.1562443-1-jrtc27@jrtc27.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The OSPI DMA reads flash data through the OSPI linear address space (the
iomem_dac region), because of this the reentrancy guard introduced in
commit a2e1753b ("memory: prevent dma-reentracy issues") is disabled for
the memory region.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@amd.com>
Message-id: 20240219105637.65052-1-sai.pavan.boddu@amd.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few watchdog devices use qemu_system_reset_request(). This is not ideal since
behaviour of watchdog-expiry can't be changed by QMP using `watchdog_action`.
As stated in BiteSizedTasks wiki page, instead of using qemu_system_reset_request()
to reset when a watchdog timer expires, let watchdog_perform_action() decide
what to do.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2124
Signed-off-by: Abhiram Tilak <atp.exp@gmail.com>
Message-id: 20240216192612.30838-5-atp.exp@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A few watchdog devices use qemu_system_reset_request(). This is not ideal since
behaviour of watchdog-expiry can't be changed by QMP using `watchdog_action`.
As stated in BiteSizedTasks wiki page, instead of using qemu_system_reset_request()
to reset when a watchdog timer expires, let watchdog_perform_action() decide
what to do.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2124
Signed-off-by: Abhiram Tilak <atp.exp@gmail.com>
Message-id: 20240216192612.30838-4-atp.exp@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no point in checking do we have PCIe if first thing after check
is adding PCIe card without checking.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240215153311.186772-1-marcin.juszkiewicz@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the previous design of ASPEED SOCs QEMU model, it set the boot
address at "0" which was the hardcode setting for ast10x0, ast2600,
ast2500 and ast2400.
According to the design of ast2700, it has a bootmcu(riscv-32) which
is used for executing SPL and initialize DRAM and copy u-boot image
from SPI/Flash to DRAM at address 0x400000000 at SPL boot stage.
Then, CPUs(cortex-a35) execute u-boot, kernel and rofs.
Currently, qemu not support emulate two CPU architectures
at the same machine. Therefore, qemu will only support
to emulate CPU(cortex-a35) side for ast2700 and the boot
address is "0x4 00000000".
Fixed hardcode boot address "0" for future models using
a different mapping address.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Aspeed datasheet refers to the UART controllers
as UART1 - UART13 for the ast10x0, ast2600, ast2500
and ast2400 SoCs and the Aspeed ast2700 introduces an UART0
and the UART controllers as UART0 - UART12.
To keep the naming in the QEMU models
in sync with the datasheet, let's introduce a new UART0 device name
and do the required adjustements.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - Kept original assert() in aspeed_soc_uart_set_chr()
- Fixed 'i' range in connect_serial_hds_to_uarts() loop ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rename "internal.h" as "ide-internal.h", and include
it via its relative local path, instead of absolute
to the project root path.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240226080632.9596-4-philmd@linaro.org>
Remove last two includes of hw/ide/intarnal.h outside of hw/ide and
replace them with newly added public header to allow moving internal.h
into hw/ide to really stop exposing it.
Fixes: a11f439a0e (hw/ide: Stop exposing internal.h to non-IDE files)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240223142633.933694E6004@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Use ahci_ide_create_devs() instead of open-coding it.
Not accessing AHCIDevice internals anymore allows to
remove "hw/ide/ahci_internal.h" (which isn't really a
public header).
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240226080632.9596-2-philmd@linaro.org>
Both the piix and the q35 machines introduce an rtc_state variable and defer the
initialization of the X86MachineState::rtc attribute to pc_cmos_init(). Resolve
this complication which makes pc_cmos_init() do what it says on the tin.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240224135851.100361-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PCMachineClass introduces the attribute into the class hierarchy and sets it to
true. There is no sub class overriding the attribute. Commit 30d2a17b46
"hw/i386: Remove the deprecated machines 0.12 up to 0.15" removed the last
overrides of this attribute. The attribute is now unneeded and can be removed.
Fixes: 30d2a17b46 "hw/i386: Remove the deprecated machines 0.12 up to 0.15"
Cc: Thomas Huth <thuth@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240224135851.100361-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
There is no advantage in having these local variables which 1/ needlessly have
different identifiers in both machines and 2/ which are redundant to pcms->bus
which is almost as short.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240224135851.100361-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The attribute is of type PCIBus; reflect that in the name. It will also make the
next change more intuitive.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240224135851.100361-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
"hw/acpi/acpi.h" is implicitly included. Include it
explicitly to avoid the following error when refactoring
headers:
hw/i386/pc_q35.c:209:43: error: use of undeclared identifier 'ACPI_PM_PROP_ACPI_PCIHP_BRIDGE'
ACPI_PM_PROP_ACPI_PCIHP_BRIDGE,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240226090600.31952-3-philmd@linaro.org>
Prefer the QDev API over the low level QOM one.
No logical change intended.
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240215142035.73331-4-philmd@linaro.org>
Rather than taking a QOM name which has to be resolved, let's pass the parent
directly as pointer. This simplifies the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-ID: <20240224135851.100361-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
numcntl is one byte and so is max_vfs. Using cpu_to_le16 on big endian
hosts results in numcntl being set to 0.
Fix by dropping the endian conversion.
Fixes: 99f48ae7ae ("hw/nvme: Add support for Secondary Controller List")
Reported-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im@samsung.com>
Message-ID: <20240222-fix-sriov-numcntl-v1-1-d60bea5e72d0@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Because USB_EHCI_SYSBUS selects USB_EHCI, there is no need to include
hcd-ehci.c explicitly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-11-pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Split the sysbus version to a separate file so that it is not
included in PCI-only machines, and adjust Kconfig for machines
that do need sysbus-ohci. The copyrights are based on the
time and employer of balrog and Paul Brook's contributions.
While adjusting the SM501 dependency, move it to the right place
instead of keeping it in the R4D machine.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-10-pbonzini@redhat.com>
[PMD: Rename some functions using 'ohci_sysbus_' prefix]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Inline the sole remaining use, which is for the -usbdevice command line.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-9-pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
With --without-default-devices it is possible to build a binary that
does not include any USB host controller and therefore that does not
include the code guarded by CONFIG_USB. While the simpler creation
functions such as usb_create_simple can be inlined, this is not true
of usb_bus_find(). Remove it, replacing it with a search of the single
USB bus on the machine.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-8-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
With --without-default-devices it should not be required to have
devices in the binary that are removed by -nodefaults. It should be
therefore possible to build a binary that does not include any USB
host controller or any of the code guarded by CONFIG_USB. While the
simpler creation functions such as usb_create_simple can be inlined,
this is not true of usb_bus_find(). Remove it, replacing it with a
search of the single USB bus on the machine.
With this change, it is possible to change "select USB_OHCI_PCI" into
an "imply" directive.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-7-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
With --without-default-devices it is possible to build a binary that
does not include any USB host controller and therefore that does not
include the code guarded by CONFIG_USB. While the simpler creation
functions such as usb_create_simple can be inlined, this is not true
of usb_bus_find(). Remove it, replacing it with a search of the single
USB bus on the machine.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-6-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Once the Kconfig for hw/mips is cleaned up, it will be possible to build a
binary that does not include any USB host controller and therefore that
does not include the code guarded by CONFIG_USB. While the simpler
creation functions such as usb_create_simple can be inlined, this is not
true of usb_bus_find(). Remove it, replacing it with a search of the
single USB bus created by loongson3_virt_devices_init().
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240223124406.234509-5-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
usb_bus_find() is always used with argument -1; it can be replaced with
a search of the single USB bus on the machine.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240223124406.234509-4-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
usb_bus_find() is always used with argument -1; it can be replaced with
a search of the single USB bus on the machine.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20240223124406.234509-3-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
object_resolve_type_unambiguous provides a useful functionality, that
is currently emulated for example by usb_bus_find(). Move it to core
code and add error reporting for increased generality.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240223124406.234509-2-pbonzini@redhat.com>
[PMD: Fixed style]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The nubus-virtio-mmio device is a Nubus card that contains a set of 32 virtio-mmio
devices and a goldfish PIC similar to the m68k virt machine that can be plugged
into the m68k q800 machine.
There are currently a number of drivers under development that can be used in
conjunction with this device to provide accelerated and/or additional hypervisor
services to 68k Classic MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20240111102954.449462-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Declaration ROM binary images can be any arbitrary size, however if a host ROM
memory region is not aligned to qemu_target_page_size() then we fail the
"assert(!(iotlb & ~TARGET_PAGE_MASK))" check in tlb_set_page_full().
Ensure that the host ROM memory region is aligned to qemu_target_page_size()
and adjust the offset at which the Declaration ROM image is loaded, since Nubus
ROM images are unusual in that they are aligned to the end of the slot address
space.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20240111102954.449462-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
sysbus_address_space() is not more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240216153517.49422-7-philmd@linaro.org>
sysbus_address_space(...) is a simple wrapper to
get_system_memory(). Use it in place, since KVM
VAPIC doesn't distinct address spaces.
Rename the 'as' variable as 'mr' since it is a
MemoryRegion type, not an AddressSpace one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240216153517.49422-6-philmd@linaro.org>
Add the Exynos4210fimdState::'framebuffer-memory' property. Have
the board set it. We don't need to call sysbus_address_space()
anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-5-philmd@linaro.org>
We want to set another qdev property (a link) for the FIMD
device, we can not use sysbus_create_varargs() which only
passes sysbus base address and IRQs as arguments. Inline
it so we can set the link property in the next commit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240216153517.49422-4-philmd@linaro.org>
Add the PL110::'framebuffer-memory' property. Have the different
ARM boards set it. We don't need to call sysbus_address_space()
anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-3-philmd@linaro.org>
We want to set another qdev property (a link) for the pl110
and pl111 devices, we can not use sysbus_create_simple() which
only passes sysbus base address and IRQs as arguments. Inline
it so we can set the link property in the next commit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240226173805.289-2-philmd@linaro.org>
One of the functions of the ChipTOD is to transfer TOD to the Core
(aka PC - Pervasive Core) timebase facility.
The ChipTOD can be programmed with a target address to send the TOD
value to. The hardware implementation seems to perform this by
sending the TOD value to a SCOM address.
This implementation grabs the core directly and manipulates the
timebase facility state in the core. This is a hack, but it works
enough for now. A better implementation would implement the transfer
to the PnvCore xscom register and drive the timebase state machine
from there.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Wire the ChipTOD model to powernv9 and powernv10 machines.
Suggested-by-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The ChipTOD (for Time-Of-Day) is a chip pervasive facility in IBM POWER
(powernv) processors that keeps a time of day clock.
In particular for this model are facilities that initialise and start
the time of day clock, and that synchronise that clock to cores on the
chip, and to other chips. In this way, all cores on all chips can
synchronise timebase (TB).
This model implements functionality sufficient to run the skiboot
chiptod synchronisation procedure (with the following core timebase
state machine implementation). It does not modify the TB in the cores
where the real hardware would, because the QEMU ppc timebase
implementation is always synchronised acros all cores.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This part of the patchset connects the nest1 chiplet model to p10 chip.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The N1 chiplet handle the high speed i/o traffic over PCIe and others.
The N1 chiplet consists of PowerBus Fabric controller,
nest Memory Management Unit, chiplet control unit and more.
This commit creates a N1 chiplet model and initialize and realize the
pervasive chiplet model where chiplet control registers are implemented.
This commit also implement the read/write method for the powerbus scom
registers
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
A POWER10 chip is divided into logical units called chiplets. Chiplets
are broadly divided into "core chiplets" (with the processor cores) and
"nest chiplets" (with everything else). Each chiplet has an attachment
to the pervasive bus (PIB) and with chiplet-specific registers. All nest
chiplets have a common basic set of registers and This model will provide
the registers functionality for common registers of nest chiplet (Pervasive
Chiplet, PB Chiplet, PCI Chiplets, MC Chiplet, PAU Chiplets)
This commit implement the read/write functions of chiplet control registers.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tests the following for both P9 and P10:
- I2C master POR status
- I2C master status after immediate reset
Tests the following for powernv10-ranier only:
- Config pca9552 hotplug device pins as inputs then
Read the INPUT0/1 registers to verify all pins are high
- Connected GPIO pin tests of P10 PCA9552 device. Tests
output of pins 0-4 affect input of pins 5-9 respectively.
- PCA9554 GPIO pins test. Tests input and ouput functionality.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
