This reverts commit 4c2c047469.
This commit tried to fix a problem with our usage of MMU indexes when
EL3 is AArch32, using what it described as a "more complicated
approach" where we share the same MMU index values for Secure PL1&0
and NonSecure PL1&0. In theory this should work, but the change
didn't account for (at least) two things:
(1) The design change means we need to flush the TLBs at any point
where the CPU state flips from one to the other. We already flush
the TLB when SCR.NS is changed, but we don't flush the TLB when we
take an exception from NS PL1&0 into Mon or when we return from Mon
to NS PL1&0, and the commit didn't add any code to do that.
(2) The ATS12NS* address translate instructions allow Mon code (which
is Secure) to do a stage 1+2 page table walk for NS. I thought this
was OK because do_ats_write() does a page table walk which doesn't
use the TLBs, so because it can pass both the MMU index and also an
ARMSecuritySpace argument we can tell the table walk that we want NS
stage1+2, not S. But that means that all the code within the ptw
that needs to find e.g. the regime EL cannot do so only with an
mmu_idx -- all these functions like regime_sctlr(), regime_el(), etc
would need to pass both an mmu_idx and the security_space, so they
can tell whether this is a translation regime controlled by EL1 or
EL3 (and so whether to look at SCTLR.S or SCTLR.NS, etc).
In particular, because regime_el() wasn't updated to look at the
ARMSecuritySpace it would return 1 even when the CPU was in Monitor
mode (and the controlling EL is 3). This meant that page table walks
in Monitor mode would look at the wrong SCTLR, TCR, etc and would
generally fault when they should not.
Rather than trying to make the complicated changes needed to rescue
the design of 4c2c047469, we revert it in order to instead take the
route that that commit describes as "the most straightforward" fix,
where we add new MMU indexes EL30_0, EL30_3, EL30_3_PAN to correspond
to "Secure PL1&0 at PL0", "Secure PL1&0 at PL1", and "Secure PL1&0 at
PL1 with PAN".
This revert will re-expose the "spurious alignment faults in
Secure PL0" issue #2326; we'll fix it again in the next commit.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20241101142845.1712482-2-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Now that all targets have been converted to explicitly set a NaN
propagation rule, we can remove the set of target ifdefs (which now
list every target) and clean up the references to fallback behaviour
for float_2nan_prop_none.
The "default" case in the switch will catch any remaining places
where status->float_2nan_prop_rule was not set by the target.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-22-peter.maydell@linaro.org
Set the NaN propagation rule explicitly for the float_status word
used in the rx target.
This not the architecturally correct behaviour, but since this is a
no-behaviour-change patch, we leave a TODO note to that effect.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-21-peter.maydell@linaro.org
Set the NaN propagation rule explicitly for the float_status word
used in the openrisc target.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-20-peter.maydell@linaro.org
Set the NaN propagation rule explicitly for the float_status word
used in the microblaze target.
This is probably not the architecturally correct behaviour,
but since this is a no-behaviour-change patch, we leave a
TODO note to that effect.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-19-peter.maydell@linaro.org
Although the floating point rounding mode for Microblaze is always
nearest-even, we cannot set it just once in the CPU initfn. This is
because env->fp_status is in the part of the CPU state struct that is
zeroed on reset.
Move the call to set_float_rounding_mode() into the reset fn.
(This had no guest-visible effects because it happens that the
float_round_nearest_even enum value is 0, so when the struct was
zeroed it didn't corrupt the setting.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-18-peter.maydell@linaro.org
Set the NaN propagation rule explicitly for the float_status word
used in this target.
This is a no-behaviour-change commit, so we retain the existing
behaviour of x87-style pick-largest-significand NaN propagation.
This is however not the architecturally correct handling, so we leave
a TODO note to that effect.
We also leave a TODO note pointing out that all this code in the cpu
initfn (including the existing setting up of env->flags and the FPCR)
should be in a currently non-existent CPU reset function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-17-peter.maydell@linaro.org
Set the NaN propagation rule explicitly for the float_status words
used in the x86 target.
This is a no-behaviour-change commit, so we retain the existing
behaviour of using the x87-style "prefer QNaN over SNaN, then prefer
the NaN with the larger significand" for MMX and SSE. This is
however not the documented hardware behaviour, so we leave a TODO
note about what we should be doing instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-16-peter.maydell@linaro.org
Set the NaN propagation rule explicitly in xtensa_use_first_nan().
(When we convert the softfloat pickNaNMulAdd routine to also
select a NaN propagation rule at runtime, we will be able to
remove the use_first_nan flag because the propagation rules
will handle everything.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-15-peter.maydell@linaro.org
In xtensa we currently call set_use_first_nan() in a lot of
places where we want to switch the NaN-propagation handling.
We're about to change the softfloat API we use to do that,
so start by factoring all the calls out into a single
xtensa_use_first_nan() function.
The bulk of this change was done with
sed -i -e 's/set_use_first_nan(\([^,]*\),[^)]*)/xtensa_use_first_nan(env, \1)/' target/xtensa/fpu_helper.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-14-peter.maydell@linaro.org
Set the NaN propagation rule explicitly in the float_status
words we use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-13-peter.maydell@linaro.org
Currently we call cpu_put_fsr(0) in sparc_cpu_realizefn(), which
initializes various fields in the CPU struct:
* fsr_cexc_ftt
* fcc[]
* fsr_qne
* fsr
It also sets the rounding mode in env->fp_status.
This is largely pointless, because when we later reset the CPU
this will zero out all the fields up until the "end_reset_fields"
label, which includes all of these (but not fp_status!)
Move the cpu_put_fsr(env, 0) call to reset, because that expresses
the logical requirement: we want to reset FSR to 0 on every reset.
This isn't a behaviour change because the fields are all zero anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-12-peter.maydell@linaro.org
In cf_fpu_gdb_get_reg() and cf_fpu_gdb_set_reg() we use a temporary
float_status variable to pass to floatx80_to_float64() and
float64_to_floatx80(), but we don't initialize it, meaning that those
functions could access uninitialized data. Zero-init the structs.
(We don't need to set a NaN-propagation rule here because we
don't use these with a 2-argument fpu operation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-11-peter.maydell@linaro.org
Explicitly set the 2-NaN propagation rule on env->fp_status
and on the temporary fp_status that we use in frem (since
we pass that to a division operation function).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Set the 2-NaN propagation rule explicitly in env->fp_status
and env->vec_status.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-9-peter.maydell@linaro.org
Set the 2-NaN propagation rule explicitly in env->fpu_status.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-8-peter.maydell@linaro.org
Set the 2-NaN propagation rule explicitly in env->fp_status.
Really we only need to do this at CPU reset (after reset has zeroed
out most of the CPU state struct, which typically includes fp_status
fields). However target/hppa does not currently implement CPU reset
at all, so leave a TODO comment to note that this could be moved if
we ever do implement reset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-7-peter.maydell@linaro.org
Set the 2-NaN propagation rule explicitly in the float_status word we
use.
(There are a couple of places in fpu_helper.c where we create a
dummy float_status word with "float_status *s = { };", but these
are only used for calling float*_is_quiet_nan() so it doesn't
matter that we don't set a 2-NaN propagation rule there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-6-peter.maydell@linaro.org
Set the 2-NaN propagation rule explicitly in the float_status words
we use.
For active_fpu.fp_status, we do this in a new fp_reset() function
which mirrors the existing msa_reset() function in doing "first call
restore to set the fp status parts that depend on CPU state, then set
the fp status parts that are constant".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20241025141254.2141506-5-peter.maydell@linaro.org
Set the 2-NaN propagation rule explicitly in the float_status words
we use. We wrap this plus the pre-existing setting of the
tininess-before-rounding flag in a new function
arm_set_default_fp_behaviours() to avoid repetition, since we have a
lot of float_status words at this point.
The situation with FPA11 emulation in linux-user is a little odd, and
arguably "correct" behaviour there would be to exactly match a real
Linux kernel's FPA11 emulation. However FPA11 emulation is
essentially dead at this point and so it seems better to continue
with QEMU's current behaviour and leave a comment describing the
situation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-4-peter.maydell@linaro.org
Explicitly set a 2-NaN propagation rule in the softfloat tests. In
meson.build we put -DTARGET_ARM in fpcflags, and so we should select
here the Arm propagation rule of float_2nan_prop_s_ab.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-3-peter.maydell@linaro.org
IEEE 758 does not define a fixed rule for which NaN to pick as the
result if both operands of a 2-operand operation are NaNs. As a
result different architectures have ended up with different rules for
propagating NaNs.
QEMU currently hardcodes the NaN propagation logic into the binary
because pickNaN() has an ifdef ladder for different targets. We want
to make the propagation rule instead be selectable at runtime,
because:
* this will let us have multiple targets in one QEMU binary
* the Arm FEAT_AFP architectural feature includes letting
the guest select a NaN propagation rule at runtime
* x86 specifies different propagation rules for x87 FPU ops
and for SSE ops, and specifying the rule in the float_status
would let us emulate this, instead of wrongly using the
x87 rules everywhere
In this commit we add an enum for the propagation rule, the field in
float_status, and the corresponding getters and setters. We change
pickNaN to honour this, but because all targets still leave this
field at its default 0 value, the fallback logic will pick the rule
type with the old ifdef ladder.
It's valid not to set a propagation rule if default_nan_mode is
enabled, because in that case there's no need to pick a NaN; all the
callers of pickNaN() catch this case and skip calling it. So we can
already assert that we don't get into the "no rule defined" codepath
for our four targets which always set default_nan_mode: Hexagon,
RiscV, SH4 and Tricore, and for the one target which does not have FP
at all: avr. These targets will not need to be updated to call
set_float_2nan_prop_rule().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20241025141254.2141506-2-peter.maydell@linaro.org
* Various fixes, improvements and additions for the functional test suite
* Restore the sh4eb target
* Fix the OpenBSD VM test
* Re-enable the pci-bridge device on s390x
* Minor clean-ups / fixes for the next-cube machine
-----BEGIN PGP SIGNATURE-----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=CTOw
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2024-11-04' of https://gitlab.com/thuth/qemu into staging
* Remove the redundant macOS-15 CI job
* Various fixes, improvements and additions for the functional test suite
* Restore the sh4eb target
* Fix the OpenBSD VM test
* Re-enable the pci-bridge device on s390x
* Minor clean-ups / fixes for the next-cube machine
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmcoyoQRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbVwRg/+M8RWxOW5M2GmEfAj/e1IatLS2eXek6fE
# YOCPxvc5VK5rjXzcRKNqNKP53gBkF0PRho68b3IkBI6ylDOdzdRcDYsi8CSLWbG4
# O6heGJRzn9HyIS+UShAoqoj9l7lxODcZvEJK2ueiy/Hri/Zc4TpullLhSgAPKTgn
# Ln75nd+hWwS9e0df1BSOBax2iEU/2j1yuBVCcFgFHH8K39Wqrs6Xtyay9yPjYLUg
# pHNGObikrLF47KGI5yZ22/iVgwr5yhd3KzycjbxHVccCqZSsGl2xkCBwKNlIodRO
# RMhTzUhOMi/RSjvdSbM5d2Nh4aCJ5mNzzWSUklHdYWnrMOv6uECJ0h2o0ve5L4kT
# jtTGTcLe8a+JsDs+UxeVWqqlUf4w8Vv0DRky6D6ln25hcqrOveJE++o58FHFt/AX
# jEolRU5k2tMpOSMgE3wAi5BVCttpI3Idly/IC+rntMjQOTwdKPlgfcBIqQmXI6M8
# dM6oUf9WnIr/CAt7qG6QjCONjeBmuMlZV4+v7xdqFsJpwCTyo6k3LwoHx3pTC73z
# 6x0SmpeDoTzdw6B7O1HlLNllW7hd2/5GQ5qTH+E1pKAktkOf3MQeSD6qQEMjwH7T
# e7hNUV+APgtDqpnQ0xcTL5AwNAkDGKoKBmaIp0vlwGUET55fw5N0Wb6Oo9LOgeFl
# yqi5GxIuJu4=
# =CTOw
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 04 Nov 2024 13:22:12 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-11-04' of https://gitlab.com/thuth/qemu:
tests/functional: Convert the OrangePi tests to the functional framework
tests/functional: Convert BananaPi tests to the functional framework
tests/functional: Convert the tcg_plugins test
next-cube: remove cpu parameter from next_scsi_init()
next-cube: fix up compilation when DEBUG_NEXT is enabled
hw/s390x: Re-enable the pci-bridge device on s390x
tests/functional: Fix the s390x and ppc64 tuxrun tests
tests/vm/openbsd: Remove the "Time appears wrong" workaround
tests/functional: Add a test for sh4eb
Revert "Remove the unused sh4eb target"
tests/functional: make cached asset files read-only
tests/functional: make tuxrun disk images writable
.gitlab-ci.d/cirrus: Remove the macos-15 job
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Please pull a single commit, which updates SeaBIOS-hppa
to version 17.
If comes with some important firmware and SCSI fixes and
prepares for futher development to support 64-bit HP-UX
and MPE/UX in the future.
New PDC functions & general enhancements:
- Add PDC_MODEL_GET_INSTALL_KERNEL firmware call
- Add PDC_PAT_EVENT firmware call
- Support ENTRY_IO_BOOTOUT
- Prefer memory-access over io-access of GSP serial port
- Disable LMMIO_DIRECT0 range during modification
- Small optimizations in IODC call
Fixes:
- esp-scsi: indicate acceptance of MESSAGE IN phase data
- Avoid crash when booting without SCSI controller
- Remove exec flag from hppa-firmware.img
- Fix LMMIO detection for PCI cards on Astro/Elroy
- Avoid trashing MPE IPL bootloader stack
- HP-UX 11 64-bit saves number of RAM pages in PAGE0 at 0x33c
- Fix return value of PDC_CACHE/PDC_CACHE_RET_SPID for space id hashing
- Allow PDC functions to act when called in narrow mode
- pcidevice: Use portaddr_t for io port addresses
Cleanups:
- Change default make target to "parisc"
- Clean the "out-64" directory on "make clean"
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZyfV0AAKCRD3ErUQojoP
X63XAP9sxLngebfWXdb9YI4+3N2xBpT772tQha3QYdejF0QvrAEAwpB8g8MFHHz3
QKZfvPERw2nBhjtpf+Dl9iexoKh8YQI=
=MjU+
-----END PGP SIGNATURE-----
Merge tag 'seabios-hppa-v17-pull-request' of https://github.com/hdeller/qemu-hppa into staging
SeaBIOS-hppa v17 pull request
Please pull a single commit, which updates SeaBIOS-hppa
to version 17.
If comes with some important firmware and SCSI fixes and
prepares for futher development to support 64-bit HP-UX
and MPE/UX in the future.
New PDC functions & general enhancements:
- Add PDC_MODEL_GET_INSTALL_KERNEL firmware call
- Add PDC_PAT_EVENT firmware call
- Support ENTRY_IO_BOOTOUT
- Prefer memory-access over io-access of GSP serial port
- Disable LMMIO_DIRECT0 range during modification
- Small optimizations in IODC call
Fixes:
- esp-scsi: indicate acceptance of MESSAGE IN phase data
- Avoid crash when booting without SCSI controller
- Remove exec flag from hppa-firmware.img
- Fix LMMIO detection for PCI cards on Astro/Elroy
- Avoid trashing MPE IPL bootloader stack
- HP-UX 11 64-bit saves number of RAM pages in PAGE0 at 0x33c
- Fix return value of PDC_CACHE/PDC_CACHE_RET_SPID for space id hashing
- Allow PDC functions to act when called in narrow mode
- pcidevice: Use portaddr_t for io port addresses
Cleanups:
- Change default make target to "parisc"
- Clean the "out-64" directory on "make clean"
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZyfV0AAKCRD3ErUQojoP
# X63XAP9sxLngebfWXdb9YI4+3N2xBpT772tQha3QYdejF0QvrAEAwpB8g8MFHHz3
# QKZfvPERw2nBhjtpf+Dl9iexoKh8YQI=
# =MjU+
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 03 Nov 2024 19:58:08 GMT
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'seabios-hppa-v17-pull-request' of https://github.com/hdeller/qemu-hppa:
target/hppa: Update SeaBIOS-hppa to version 17
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZyXbXgAKCRBAov/yOSY+
37a9BADZ7vI2idWNXdH+mLNDZNSOxfdKp6ggNgKS3S48Hi2zR72MEhwvR9dGlHDL
98agrbV7/jI9Z+0dLAxvlyl1MvXfnn2sXYgUuZp6IAaQzFBa11HBAK7UFh3sTA4A
gD4oPwl8AdJiFvDN6vNjS+dO0ls+j/YMaoLkAKLv15dlWtg4Rw==
=EZnr
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20241102' of https://gitlab.com/gaosong/qemu into staging
pull-loongarch-20241102
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZyXbXgAKCRBAov/yOSY+
# 37a9BADZ7vI2idWNXdH+mLNDZNSOxfdKp6ggNgKS3S48Hi2zR72MEhwvR9dGlHDL
# 98agrbV7/jI9Z+0dLAxvlyl1MvXfnn2sXYgUuZp6IAaQzFBa11HBAK7UFh3sTA4A
# gD4oPwl8AdJiFvDN6vNjS+dO0ls+j/YMaoLkAKLv15dlWtg4Rw==
# =EZnr
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 02 Nov 2024 07:57:18 GMT
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20241102' of https://gitlab.com/gaosong/qemu:
target/loongarch: Add steal time support on migration
hw/loongarch/boot: Use warn_report when no kernel filename
linux-headers: Update to Linux v6.12-rc5
linux-headers: loongarch: Add kvm_para.h
linux-headers: Add unistd_64.h
target/loongarch/kvm: Implement LoongArch PMU extension
target/loongarch: Implement lbt registers save/restore function
target/loongarch: Add loongson binary translation feature
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the OrangePi tests from tests/avocado/boot_linux_console.py into
a new file dedicated for OrangePi tests in the functional framework
and update the hash sums of the assets to sha256 along the way.
For the buildroot image and the Armbian image, we've got to switch to
a newer version since the old images have been removed from the server,
and the NetBSD image has been moved to the archive, so we need to update
this URL as well.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241029092440.25021-3-thuth@redhat.com>
Move the BananaPi tests from tests/avocado/boot_linux_console.py into
a new file dedicated for Banana Pi tests in the functional framework.
Update the hash sums of the assets to sha256 along the way and fix the
broken link for the buildroot image from storage.kernelci.org.
(Note: The test_arm_bpim2u_openwrt_22_03_3 test is currently broken
due to a regression in commit 4c2c047469 ("target/arm: Fix usage of MMU
indexes when EL3 is AArch32") - it works if that commit gets reverted)
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241029092440.25021-2-thuth@redhat.com>
A straight forward conversion, only the usual changes were required
here (i.e. adjustment for asset downloading, machine selection).
Message-ID: <20241023051754.813412-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The parameter is not used.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-ID: <20241023085852.1061031-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
These were accidentally introduced by my last series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-ID: <20241023085852.1061031-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Commit e779e5c05a ("hw/pci-bridge: Add a Kconfig switch for the
normal PCI bridge") added a config switch for the pci-bridge, so
that the device is not included in the s390x target anymore (since
the pci-bridge is not really useful on s390x).
However, it seems like libvirt is still adding pci-bridge devices
automatically to the guests' XML definitions (when adding a PCI
device to a non-zero PCI bus), so these guests are now broken due
to the missing pci-bridge in the QEMU binary.
To avoid disruption of the users, let's re-enable the pci-bridge
device on s390x for the time being.
Message-ID: <20241024130405.62134-1-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
I forgot to add the tests to the meson.build file and looks
like I even managed to somehow mix up the hashsums in the
ppc64 test!
Message-ID: <20241023141919.930689-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Seems like the server now reports the right time again, so we have
to drop the workaround to get the installer working again.
Message-ID: <20241023072414.827732-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Now that we are aware of binaries that are available for sh4eb,
we should make sure that there are no regressions with this
target and test it regularly in our CI.
Message-ID: <20241024082735.42324-3-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This reverts commit 73ceb12960.
The "r2d" machine can work in big endian mode, see:
https://lore.kernel.org/qemu-devel/d6755445-1060-48a8-82b6-2f392c21f9b9@landley.net/
So the reasoning for removing sh4eb was wrong.
Message-ID: <20241024082735.42324-2-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Rob Landley <rob@landley.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This ensures that if a functional test runs QEMU with a writable
disk pointing to a cached asset, an error will be reported, rather
than silently modifying the cache file.
As an example, tweaking test_sbsaref.py to set snapshot=off,
results in a clear error:
Command: ./build/qemu-system-aarch64 ...snip... -drive file=/var/home/berrange/.cache/qemu/download/44cdbae275ef1bb6dab1d5fbb59473d4f741e1c8ea8a80fd9e906b531d6ad461,format=raw,snapshot=off -cpu max,pauth=off
Output: qemu-system-aarch64: Could not open '/var/home/berrange/.cache/qemu/download/44cdbae275ef1bb6dab1d5fbb59473d4f741e1c8ea8a80fd9e906b531d6ad461': Permission denied
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241025092659.2312118-3-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The zstd command will preserve the input archive permissions on the
output file. So when we decompress the readonly cached image, the
resulting per-test run private disk image will also be readonly.
We need it to be writable, so make it so.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241025092659.2312118-2-berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Cirrus-CI stopped providing the possibility to run macOS 15 jobs.
Quoting https://cirrus-ci.org/guide/macOS/ :
"Cirrus CI Cloud only allows ghcr.io/cirruslabs/macos-runner:sonoma image ..."
If you still try to run a Sequoia image, it gets automatically "upgraded"
to Sonoma instead. So the macos-15 job in the QEMU CI now does not
make sense anymore, thus let's remove it.
Message-ID: <20241021124722.139348-1-thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
v2:
- Patch "migration: Move cpu-throttle.c from system to migration",
fix build on MacOS, and subject spelling
NOTE: checkpatch.pl could report a false positive on this branch:
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#21:
{include/sysemu => migration}/cpu-throttle.h | 0
That's covered by "F: migration/" entry.
Changelog:
- Peter's cleanup patch on migrate_fd_cleanup()
- Peter's cleanup patch to introduce thread name macros
- Hanna's error path fix for vmstate subsection save()s
- Hyman's auto converge enhancement on background dirty sync
- Peter's additional tracepoints for save state entries
- Thomas's build fix for OpenBSD in dirtyrate.c
- Peter's deprecation of query-migrationthreads command
- Peter's cleanup/fixes from the "export misc.h" series
- Maciej's two small patches from multifd+vfio series
-----BEGIN PGP SIGNATURE-----
iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZyTbVRIccGV0ZXJ4QHJl
ZGhhdC5jb20ACgkQO1/MzfOr1wan3wD+L4TVNDc34Hy4mvWu7u1lCOePX0GBdUEc
oEeBGblwbrcBAIR8d+5z9O5YcWH1coozG1aUC4qCtSHHk5TGbJk4/UUD
=XB5Q
-----END PGP SIGNATURE-----
Merge tag 'migration-20241030-pull-request' of https://gitlab.com/peterx/qemu into staging
Migration pull request for softfreeze
v2:
- Patch "migration: Move cpu-throttle.c from system to migration",
fix build on MacOS, and subject spelling
NOTE: checkpatch.pl could report a false positive on this branch:
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#21:
{include/sysemu => migration}/cpu-throttle.h | 0
That's covered by "F: migration/" entry.
Changelog:
- Peter's cleanup patch on migrate_fd_cleanup()
- Peter's cleanup patch to introduce thread name macros
- Hanna's error path fix for vmstate subsection save()s
- Hyman's auto converge enhancement on background dirty sync
- Peter's additional tracepoints for save state entries
- Thomas's build fix for OpenBSD in dirtyrate.c
- Peter's deprecation of query-migrationthreads command
- Peter's cleanup/fixes from the "export misc.h" series
- Maciej's two small patches from multifd+vfio series
# -----BEGIN PGP SIGNATURE-----
#
# iIgEABYKADAWIQS5GE3CDMRX2s990ak7X8zN86vXBgUCZyTbVRIccGV0ZXJ4QHJl
# ZGhhdC5jb20ACgkQO1/MzfOr1wan3wD+L4TVNDc34Hy4mvWu7u1lCOePX0GBdUEc
# oEeBGblwbrcBAIR8d+5z9O5YcWH1coozG1aUC4qCtSHHk5TGbJk4/UUD
# =XB5Q
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Nov 2024 13:44:53 GMT
# gpg: using EDDSA key B9184DC20CC457DACF7DD1A93B5FCCCDF3ABD706
# gpg: issuer "peterx@redhat.com"
# gpg: Good signature from "Peter Xu <xzpeter@gmail.com>" [marginal]
# gpg: aka "Peter Xu <peterx@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: B918 4DC2 0CC4 57DA CF7D D1A9 3B5F CCCD F3AB D706
* tag 'migration-20241030-pull-request' of https://gitlab.com/peterx/qemu:
migration/multifd: Zero p->flags before starting filling a packet
migration/ram: Add load start trace event
migration: Drop migration_is_idle()
migration: Drop migration_is_setup_or_active()
migration: Unexport ram_mig_init()
migration: Unexport dirty_bitmap_mig_init()
migration: Take migration object refcount earlier for threads
migration: Deprecate query-migrationthreads command
migration/dirtyrate: Silence warning about strcpy() on OpenBSD
tests/migration: Add case for periodic ramblock dirty sync
migration: Support periodic RAMBlock dirty bitmap sync
migration: Remove "rs" parameter in migration_bitmap_sync_precopy
migration: Move cpu-throttle.c from system to migration
migration: Stop CPU throttling conditionally
accel/tcg/icount-common: Remove the reference to the unused header file
migration: Ensure vmstate_save() sets errp
migration: Put thread names together with macros
migration: Cleanup migrate_fd_cleanup() on accessing to_dst_file
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is SeaBIOS for the hppa architecture v17.
If comes with some important firmware and SCSI fixes and
prepares for futher development to support 64-bit HP-UX
and MPE/UX in the future.
New PDC functions & general enhancements:
- Add PDC_MODEL_GET_INSTALL_KERNEL firmware call
- Add PDC_PAT_EVENT firmware call
- Support ENTRY_IO_BOOTOUT
- Prefer memory-access over io-access of GSP serial port
- Disable LMMIO_DIRECT0 range during modification
- Small optimizations in IODC call
Fixes:
- esp-scsi: indicate acceptance of MESSAGE IN phase data
- Avoid crash when booting without SCSI controller
- Remove exec flag from hppa-firmware.img
- Fix LMMIO detection for PCI cards on Astro/Elroy
- Avoid trashing MPE IPL bootloader stack
- HP-UX 11 64-bit saves number of RAM pages in PAGE0 at 0x33c
- Fix return value of PDC_CACHE/PDC_CACHE_RET_SPID for space id hashing
- Allow PDC functions to act when called in narrow mode
- pcidevice: Use portaddr_t for io port addresses
Cleanups:
- Change default make target to "parisc"
- Clean the "out-64" directory on "make clean"
Signed-off-by: Helge Deller <deller@gmx.de>
With pv steal time supported, VM machine needs get physical address
of each vcpu and notify new host during migration. Here two
functions kvm_get_stealtime/kvm_set_stealtime, and guest steal time
physical address is only updated on KVM_PUT_FULL_STATE stage.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240930064040.753929-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
When we run “qemu-system-loongarch64 -qmp stdio -vnc none -S”,
we get an error message “Need kernel filename” and then we can't use qmp cmd to query some information.
So, we just throw a warning and then the cpus starts running from address VIRT_FLASH0_BASE.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20241030012359.4040817-1-gaosong@loongson.cn>
update linux-headers to v6.12-rc5. Pass to compile on aarch64, arm,
loongarch64, x86_64, i386, riscv64,riscv32 softmmu and linux-user.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-4-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
KVM LBT supports on LoongArch depends on the linux-header file
kvm_para.h, add header file kvm_para.h here.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
since 6.11, unistd.h includes header file unistd_64.h directly on
some platforms, here add unistd_64.h on these platforms. Affected
platforms are ARM64, LoongArch64 and Riscv. Otherwise there will
be compiling error such as:
linux-headers/asm/unistd.h:3:10: fatal error: asm/unistd_64.h: No such file or directory
#include <asm/unistd_64.h>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Acked-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20241028023809.1554405-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Implement PMU extension for LoongArch kvm mode. Use OnOffAuto type
variable pmu to check the PMU feature. If the PMU Feature is not supported
with KVM host, it reports error if there is pmu=on command line.
If there is no any command line about pmu parameter, it checks whether
KVM host supports the PMU Feature and set the corresponding value in cpucfg.
This patch is based on lbt patch located at
https://lore.kernel.org/qemu-devel/20240904061859.86615-1-maobibo@loongson.cn
Co-developed-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240918082315.2345034-1-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Six registers scr0 - scr3, eflags and ftop are added in percpu vmstate.
And two functions kvm_loongarch_get_lbt/kvm_loongarch_put_lbt are added
to save/restore lbt registers.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240929070405.235200-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Loongson Binary Translation (LBT) is used to accelerate binary
translation, which contains 4 scratch registers (scr0 to scr3), x86/ARM
eflags (eflags) and x87 fpu stack pointer (ftop).
Now LBT feature is added in kvm mode, not supported in TCG mode since
it is not emulated. Feature variable lbt is added with OnOffAuto type,
If lbt feature is not supported with KVM host, it reports error if there
is lbt=on command line.
If there is no any command line about lbt parameter, it checks whether
KVM host supports lbt feature and set the corresponding value in cpucfg.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240929070405.235200-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
This way there aren't stale flags there.
p->flags can't contain SYNC to be sent at the next RAM packet since syncs
are now handled separately in multifd_send_thread.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Link: https://lore.kernel.org/r/1c96b6cdb797e6f035eb1a4ad9bfc24f4c7f5df8.1730203967.git.maciej.szmigiero@oracle.com
Signed-off-by: Peter Xu <peterx@redhat.com>
